BENCH GRINDER PEDESTAL STAND
Model 42986
ASSEMBLY AND OPERATING INSTRUCTIONS
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2000 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein
may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within
this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from
the product described herein. Tools required for assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 10l
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Using
Before using any tool, any part that appears damaged should be carefully checked to
determine that it will operate properly and perform its intended function.
Make sure all Nuts and Bolts are tight.
Use only Bench Grinders that are fully compatible with the Bench Grinder Pedestal Stand. The Bench Grinder
Pedestal Stand fits most Harbor Freight Tool Bench Grinders, but you should always check for sure before using.
Use of the Pedestal Stand is for use with bench grinders only.
Assembly
Your Pedestal Stand will require assembly prior to use. It is important that you read the entire manual to
become familiar with the unit BEFORE you set up the Stand. Before assembling your Stand, be sure that
you have all parts described in the Parts List and Parts Diagram on the last pages of this manual.
Set out all parts on a clear work surface prior to assembly.
Warning:
Use only bench grinders that are fully compatible with the Bench Grinder Pedestal
Stand. Using bench grinders which do not fit this stand may result in harm or serious
injury to the operator. The Bench Grinder Pedestal Stand fits most Harbor Freight
Tool Bench Grinders, but you should always check for sure before using.
Use the Pedestal Stand for bench grinders only.
Step 1)
Mount the Base (3) to a heavy-duty block of wood which is larger than the Pedestal Stand
Base, or into cement for safety and stability. A rubber mat should be placed between
the Base (#3) and the mounting surface to reduce vibration. The Mounting Holes on
the Base (3) are 3/8” in diameter. Insert appropriate screws (not included) through the
Base (3) and into a flat and secure surface. The mounting surface must be able to
support the weight of the Stand as well as the Grinder and work pieces during use.
Step 2)
Step 3)
Insert the Column (#2) into the hole in the Base (3). Insert a Bolt (4) into each
hole in the Base (3) and tighten them firmly against the Column (2).
Slide the Work Table (1) into place on top of the Column (2). Thread one Bolt (4) through
each hole in the WorkTable. Tighten the Bolts (4) until they are firmly against the Column.
Step 4)
Step 5)
Make certain that all Bolts (4) are tightly in place and that the Stand is secure.
Secure the bench grinder to the Work Table (#1) with six appropriate
size bolts, washers and nuts (not included).
Step 6)
Make sure that the Pedestal Stand and the bench grinder are secure before using.
SKU 42986
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
UNPACK AND CHECK CONTENTS
When unpacking your Bench Grinder Pedestal Stand, check to make sure the following parts are included.
If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353.
Part
Description
Work Table
Column
Quantity
1
2
3
4
1
1
1
4
Base
Bolt M8 x 24
Note: Some parts are listed and shown for illustration purposes only
and are not available individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURERAND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES
THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Page 4
For technical questions, please call 1-800-444-3353.
SKU 42986
Download from Www.Somanuals.com. All Manuals Search And Download.
|