model t23084
5" pneumatic angle grinder
instruction manual
Copyright © DECEMBEr, 2010 By grizzly inDustrial, inC.
Warning: no portion of this manual may be reproduced in any shape
or form Without the Written approval of grizzly industrial, inc.
#ts13540 printED in China
Download from Www.Somanuals.com. All Manuals Search And Download.
safety
for your own safety read instruction manual
before operating this equipment
the purpose of safety symbols is to attract your attention to possible hazardous
conditions. this manual uses a series of symbols and signal words which
are intended to convey the level of importance of the safety messages. the
progression of symbols is described below. remember that safety messages by
themselves do not eliminate danger and are not a substitute for proper accident
prevention measures.
indicates an imminently hazardous situation which,
if not avoided, Will result in death or serious injury.
indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury.
indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury.
it may also be used to alert against unsafe practices.
this symbol is used to alert the user to useful
NOTICE
information about proper operation of the equipment.
safety instructions for pneumatic tools
1. read this manual. this tool may
cause personal injury if used incor-
rectly. this manual contains proper
safety and operating instructions that
must be followed to reduce this risk.
2. Wear eye protection. this
tool may throw small fragments dur-
ing operation, which may cause seri-
ous eye injury. always wear ansi
approved safety glasses or face shield
to reduce your risk from this hazard.
3. Wear a respirator. this tool
may produce fine dust during oper-
ation, which can cause respiratory
injury if inhaled. always wear a respi-
rator niosh approved for the type of
material being processed.
4. Wear hearing protection.
operating this tool for prolonged time
periods may damage your hearing.
your risk depends on length and fre-
quency of use. to reduce your risk of
this hazard, wear hearing protection.
5. maintain safety guards. your
tool may be equipped with safety
guards or other structural compo-
nents designed to reduce the risk of
injury during operation. never modify
or operate this tool with any guards or
components removed or damaged.
6. Keep children aWay. prevent
children from injury by keeping them
away from this tool. Disconnect and
lock the tool away when not in use.
t23084 (Mfg since 11/10)
-1-
Download from Www.Somanuals.com. All Manuals Search And Download.
7. avoid entanglements. Do not
wear loose clothing, gloves, neck-
ties, rings, bracelets, or other jewel-
ry, which may get caught in moving
parts, when operating this tool. Wear
a protective hair covering to contain
long hair.
8. use correct air pressure.
Exceeding the maximum psi rating
of this tool may cause unpredictable
operation or bursting.
9. disconnect air pressure
before servicing, changing accesso-
ries, or moving to another location.
never leave this tool unattended
when connected to air.
10. secure tooling. always verify
tooling is secure before operation.
11. sharp surfaces. Do not
place hands near the tooling sur-
faces when in operation.
12. remove adJusting Keys and
Wrenches after use. these
tools become dangerous projectiles
if left on the tool when it is started.
13. avoid flammables. Do not use
this tool around any flammables that
may be ignited by sparks.
14. secure WorK. use clamps or a
vise to hold work when practical. it is
safer than using your hand and frees
both hands to operate tool.
15. maintain tools With care.
Keep tools lubricated and clean
for best and safest performance.
Follow instructions for lubricating
and changing accessories.
16. do not force tool. it will do
the job better and safer at the rate
for which it was designed.
17. checK for damaged parts
before using. Check for bind-
ing and alignment of parts, broken
parts, part mounting, loose bolts,
and any other conditions that may
affect operation. repair or replace
damaged parts before operating.
18. use good lighting. Keep work
area well lighted. Dark work areas
increase risk of accidental injury.
19. avoid
unintentional
operation. always disconnect air
when not in use, and do not carry
tool with hand on trigger.
20. use
the
recommended
accessories. Consult owner’s
manual for recommended acces-
sories. using improper accessories
may increase the risk of injury.
21. never alloW untrained
users to use this tool While
unsupervised.
22. if you are unsure of the
intended operation, stop
using tool. seek formal training
or research books or magazines that
specialize in pneumatic tools.
23. be aWare of hose location.
hoses can easily become a tripping
hazard when laid across the floor in
a disorganized fashion.
24. do not use under the
influence of drugs or
alcohol, or When tired.
like all machinery there is potential danger when operating
this machine. accidents are frequently caused by lack of
familiarity or failure to pay attention. use this machine with
respect and caution to lessen the possibility of operator
injury. if normal safety precautions are overlooked or ignored,
serious personal injury may occur.
-2-
t23084 (Mfg since 11/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Specifications
Foreword
The
specifications,
details,
and
Arbor Speed .........Variable 0–11,000 RPM
Arbor Size..........................................5⁄8"-11
Grinding Wheel Diameter........................5"
photographs in this manual represent
the Model T23084 as supplied when the
manual was prepared. However, owing to
Grizzly’s policy of continuous improvement,
changes may be made at any time with no
obligation on the part of Grizzly.
Grinding Wheel Bore.............................. 7⁄8
"
Grinding Wheel Type.............................. 27
Air Inlet ...........................................1⁄4" NPT
Average Air Consumption ............... 6 CFM
Maximum Air Pressure.................... 90 PSI
Weight ................................................4 lbs.
If you have any comments regarding this
manual, please write to us at the following
address:
Inventory
Grizzly Industrial, Inc.
C/O Technical Documentation
P.O. Box 2069
Bellingham, WA 98227-2069
E-Mail: [email protected]
B
A
Most importantly, we stand behind our
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
D
C
E
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Figure 1. Model T23084 Inventory.
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
Description
Qty
A. Handle................................................ 1
B. Angle Grinder Assembly w/Wheel ..... 1
C. Quick Disconnect Coupler ................. 1
D. Arbor Wrench..................................... 1
E. Flange Spanner Wrench.................... 1
Nolistofsafetyguidelinesiscomplete,
because every work environment is
different. Always consider safety first
and use common sense. Failure to
use this tool with caution and respect
could result in serious personal
injury.
Assembly
Thread the handle into the housing, as
shown in Figure 1 above.
T23084 (Mfg Since 11/10)
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
operations
to change the grinding wheel:
1. DisConnECt grinDEr FroM air!
2. position the arbor wrench on the arbor
flats behind the inner arbor flange (see
figure 2).
arbor Wrench
read the manual before operation.
become familiar with this tool, its
safety instructions, and its operation
before beginning any work. serious
personal injury may result if safety
or operational information is not
understood or followed.
Flange spanner
Wrench
figure 2. loosening the outer arbor
flange.
changing grinding Wheels
the Model t23084 uses type 27, 5"
7
grinding wheels with a ⁄8" bore. see the
3. insert the prongs of the flange span-
ner wrench into the holes on the outer
arbor flange, then rotate the flange
counterclockwise to unthread it from
the arbor.
a complete listing of available grinding
wheels.
4. remove the grinding wheel.
an incorrect size or type of grinding
wheel will not work properly with
this grinder and could fly apart
and cause operator injury. always
5. use the wrenches to make sure the
inner arbor flange is tight, then slide the
replacement grinding wheel onto the
arbor.
make sure to install only type 27, 5"
7
grinding wheels with a
this grinder.
⁄8" bore on
6. Make sure the protruding lip of the outer
arbor flange is seated into the grinding
wheel bore, then use the wrenches to
fully tighten the flange and secure the
grinding wheel.
-4-
t23084 (Mfg since 11/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
eye inJury
hazard!
lung/ear inJury
hazard!
Wear protective
equipment when
using this tool.
Wear protective
equipment when
using this tool.
accidental start
hazard!
disconnect before
service or tool
changes.
using grinder
always test the grinder on a scrap piece
of material similar to the workpiece to
determine the ideal setup.
air pressure
hazard!
never exceed max
psi rating for tool.
to use the grinder:
1. Make sure the workpiece is securely
held in a vise or a similar device that
will ensure the workpiece does not
unexpectedly move during operation.
daily maintenance
the angle grinder Must have 4-5 drops
of pnmtl rty oped into
the air inlet port before and after each
use. in addition, add oil after 1–2 hours
of continuous use or install an in-line
filter, lubricator, and regulator, as shown
in figure 3.
2. attach the grinder to an air supply set
at no more than 90 psi.
3. hold the grinder securely, turn the
grinder ON by depressing the trigger,
then ease the grinding wheel against
the workpiece with a light, but steady,
pressure.
these procedures should be done after
each use:
note: The pressure applied to the trig-
ger varies the grinder speed.
•
Wipe the grinding housing with a dry
cloth, or blow off the dust and debris
with compressed air.
4. to turn the grinder OFF, release the
trigger.
•
Check for damage to grinding wheels,
hoses, housing, or other accessories.
note: To avoid accidental start up,
disconnect the grinder from the air sup-
ply when it is not in use. Replace the
protective cap over the air inlet port to
keep dust or debris out of the internal
components.
Quick
Connector
Quick
Connector
Lubricator
Regulator
Your
Tool
Air
Compressor
Quick
Coupler
Quick
Coupler
Air Hose
Filter
figure 3. installed filter lubricator
regulator.
t23084 (Mfg since 11/10)
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
parts
44
22
28
1
49
27
26
25
35
3
23
2
24
22
21
4
6
5
7
33
8
36
9
34
20
37
10
11
12
46
45
47
48
32
13
30
43
31
14
16
38
40
39
41
15
19
29
17
18
42
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
2
3
4
5
6
7
8
9
PT23084001 MAIN HOUSING
26 PT23084026 ROTOR
PS79M
PHLP HD SCR M3-.5 X 8
27 PT23084027 ROTOR BLADE
PT23084003 AIR OUTLET PLATE
28 PT23084028 ROTOR CYLINDER REAR CAP
29 PT23084029 HOUSING COUPLER
30 PT23084030 COUPLER NUT
PS68M
PHLP HD SCR M6-1 X 10
PT23084005 HANDLE
PT23084006 O-RING 12.5MM
31 PT23084031 REAR HOUSING
P626ZZ
PR45M
BALL BEARING 626ZZ
INT RETAINING RING 10MM
32 PT23084032 VALVE CAP BRASS
33 PT23084033 TRIGGER
PT23084009 O-RING 10MM
34 PT23084034 TRIGGER LOCK
10 PT23084010 BEVEL GEAR
11 P6206ZZ BALL BEARING 6206ZZ
35 PT23084035 TORSION SPRING
36 PT23084036 ROLL PIN 3 X 1.8
37 PT23084037 ROLL PIN 4 X 2.8
38 PT23084038 VALVE STEM
12 PT23084012 WOODRUFF KEY 12.6 X 3 X 4.5
13 PT23084013 ARBOR 9/16-12
14 PT23084014 HOUSING GASKET
39 PT23084039 VALVE CAP RUBBER
40 PT23084040 COMPRESSION SPRING
41 PT23084041 O-RING 11MM
15 PT23084015 INNER ARBOR FLANGE
16 PT23084016 GRINDING WHEEL GUARD
17 PLW01M
18 PCAP50M
LOCK WASHER 5MM
42 PT23084042 BUSHING BRASS
43 PT23086001 AIR INLET PORT 1/4" NPT
44 PT23084044 GRIP RUBBER
CAP SCREW M5-.8 X 10
19 PT23084019 OUTER ARBOR FLANGE
20 PT23084020 BEVEL GEAR
45 PT23084045 FLANGE SPANNER WRENCH
46 PT23084046 ARBOR WRENCH
47 PT23086037 QUICK DISCONNECT 1/4" NPT
48 PT23083038 PROTECTIVE AIR INLET CAP
49 PT23084049 GRIZZLY LOGO LABEL
21 P6201ZZ
22 P608ZZ
BALL BEARING 6201ZZ
BALL BEARING 608ZZ
23 PT23084023 ROTOR CYLINDER FRONT CAP
24 PT23084024 ROTOR CYLINDER
25 PCAP80M
CAP SCREW M3-.5 X 8
-6-
t23084 (Mfg since 11/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
|