Fuzzy Computerized Automatic
Washing Machine
User's manual
This manual is for
HWM8000
Please read this manual
carefully before using.
Retain it for future reference.
0030805704B
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of the parts
Top lid A
Cool water valve
Warm water valve
Back faceplate
Top lid B
Drier outlet
cover
Detergent box
Control panel
Level meter
Power line
Inner tub
Cabinet handle
Lint filter(Installed by user)
hanging hole
for the drain
hose
Filter cover
Drain hose
Control panel
film
back cover
Front control
board
Front fixed
foot
Adjustable foot
seam
Pulsator
Cabinet
Adjustable foot
Rear fixed foot
Meaning and description of the symbols
Contents marked with that symbol are related
to the safety of the product and the personal
safety of the users. Please operate in strict
conformity to the contents, otherwise it may
cause damageof the machine or injure the
personal safety of the user.
Warning sign
Contents marked with that symbol are actions
forbidden to perform. Performing of those
actions may result in damage of the machine
or injure the personal safety of the user.
Forbidding sign
Please check if the power receptacle has good earthing condition
before using to guarantee your safety.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety precautions
In normal usage of thewashing machine,
Please insert the power cord into special
receptacle with rated voltage.Be sure to
use single-phase three pins receptacle.
The earthing terminal must be earthed
reliably.If possible,please adopt electric
leakage protector.
the power plug shall be ready to be pulled
or plugged with hand. Be sure to pull the
plug off and close the water faucet in
following cases: power failure, delivering
the machine, setting the machine idle or
cleaning the machine. Do not plug
or pull the power plug with wet hand.
Do not bend, stretch, twist, bind the power cord by force,
or reform it. Do not press or clamp it with heavy items. If the
power cord and power plug are bad, or the receptacle is loose,
be sure tohave it replacedby the techniciansof our specialshop
or our agent, or the after-sale service department for the sake
of avoiding any risk. Keep the prong of the power plug clean.
If dust isfound on thepower plug, pleasewipe it offwith dry cloth.
In case the washing machineis installed on
ground with carpet,be careful notto block the
ventilation hole withcarpet.
Do not use water with temperature
higher than 50 inside the tub.
The ventilation
holes at the
bottom
Do not set the machine at dampplace
like the bathroom.Never wash itwith water.
Do not put wet laundries on the control
panel coating.
Do notwash water-proof laundries like
the raincoat, bike covers,down textiles etc.
to avoid abnormalvibrations in spinning and
damaging the laundries.
Do not letthe machine shareone receptacle withother
electric appliances. Ifthe power plugis damaged, orthe
plugging into thereceptacle is loose,do not useit any
more.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety precautions
Do not put hand intothe rotating tub. It is
dangerous even ifthe rotation speedis slow.
Take special care of thechildren. Keep
children away from the washing machine
to avoid themclimbing on it.
Do not decompose, repairor alter
the machine byyourself.
Do not put any hot or heavy items
(such as thekettle with hotwater) on the
washing machine.
Do notwash laundrieswith volatile
materials (such asthinner, petroletc.).
Keep themachine away from direct
sunlight and heatsource like theheater.
The handicappedor childrenshall not
use the machinewithout care.
To protect your laundries and washing
machine, please take out all of the coins,
buttons, sand, hairpin and other foreign
materials before washing.
Toprevent the lintin the tubfrom blocking
the cascade outlet and influencing the
cascade effect, please keep the lint filter
in good condition, and install it to proper
position during washing. If the lint filter is
lost or damaged, please contact the local
after-sale service department of our
company.
Please check if the water faucet is open, and if
the connection of the water inlet pipe is proper.
It is suggested to use foamless washing powder.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual, which is very
important for you to operate the machine safely and properly.
Install the bottom plate
After opening the package, please lean the
washing machine gently down on soft items
(like towel cloth, blanket, etc.). Install the
bottom plate to the bottom of the machine
Back
Front
with eight screws by
a
cross screwdriver,
then lift the machine up gently. See to the
figure:
Soft item
Bottom plate
Screw
Adjust the installation position
The largest allowable slope of the shank base
of the machine is 2 . The slanting or rough
ground will result in unstable running or
stoppage of the machine. Please adjust it with
following methods:
Confirm it's horizontal:
Air bubble
If the bulb of the level meter at the balance display
position is inside the standard circle, it indicates that
the machine is horizontal. Otherwise you need to
adjust the adjustable leg of the machine.
Suitable
Not suitable
Standard circle
Adjust theadjustable leg:
1.Totwist the adjustableleg, please firstlift up the
leg side slightly, loosen theadjustable nut, and
then twist theleg.
Adjustable nut
Fasten
Adjustable leg
Loosen
High
2.After adjustment, fastenthe nut.
Low
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Install the lint filter
After opening the package, please takeout the lint
filter from the document bag, install it to the filter cover
of inner tub. See to thefigure.
Inner tub
Lint filter
How to change the direction of the drain hose
1.Dismount the back cover of the washing machine.
2.Lay down the washing machine gently with the front
side facing the ground. Use cross screwdriver to
loosen the eight screws. Take off the bottom plate.
4.Dismount the protecting cover of the drain outlet at the
other side as indicated in Figure 3.
5.Extend the drain hose out of the other side. Fix the drain
hose onto the cabinet with the drain hose rack. Set the
drain hose nut on, and fasten the nut to the direction
indicated in the figure, as per Figure 4.
back
bottom plate
drain outlet
protecting
cover
front
soft item
fasten
3.Put down the outer drain hose. Twist the drain hose nut
counterclockwise to take it off as indicated in Figure 1.
Take off the drain hose rack. Put the drain hose into
the cabinet as indicated in Figure 2.
Figure 3
Figure 4
6.Install the protecting cover of the drain outlet to the other
side, as indicated in Figure 5.
Loosen
Figure 5
Outer
drain hose
7.Install the bottom plate (method the same as stated
above). Lift up the washing
machine gently.
Drain hose nut
Drain hose rack
drain hose nut
Figure 2
Page 4
Figure 1
Usage of the drain hose
The drain hose shall drain smoothly
4.If extra drain hose is needed, please
1.The height of the drain hose shall be
less than 10cm, or the drainage will not
be smooth, and cost such long time that
make separate purchase. The inner
diameter of the extra hose shall not
less than 30mm, and the length shall
not exceed 1.5m.
the machine may stop at mid way.
2.Do not ramp or press the drain hose.
3.If the drain hose is too long, cut it at mid
point. Tomake smooth drainage, cut the
front end of the hose slantingly.
f the extra hose is too long, cut it either
at point A or B.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Install the water inlet hose
Install the water inlet pipe
Water faucet, suitable
water faucet, not suitable
It is required that the front end shall be longer than 10mm.
The outlet end surface of the faucet shall be flat and smooth. If not, please file it smooth to avoid leakage.
Connection between the water inlet hose jointer and the water faucet
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
2 Loosen the four screws of the water inlet hose jointer till the water faucet can be accessed. Then set the water inlet hose
jointer on the faucet. See to Figure 2. If the faucet is too large and the jointer cannot be set on, please loosen the four
screws and take out the bush inside the jointer. See to Figure 3.
Water inlet hose jointer
Screw
Slider
Nameplate
Bushing
Screw knife
Lock level
Water inlet hose
Figure 1
Figure 2
Figure 3
3 Fasten the four screws of the water inlet hose jointer evenly. See to Figure 4.
4 Take off the nameplate.Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
Remark: .Before installation, the threading is 4mm above the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut..
About 4mm after twisting
About above 2mm after twisting
Screw nut
Figure 4
Figure 5
Figure 6
Connection between the water inlet hose and the washing machine
1 Do not takeoff the waterabsorption cushion. Pleasecheck
Water inlet
hose nut
if the cushion isdropped or damaged eachtime before using.
If it happens so,please duly contact ourafter-sale service
department.
2 Set the nutof the water inlethose on the waterinlet valve jointer.
3 Fasten the nut.Swing it gently toconfirm if it's fastenedwell.
Water inlet valvejointer Water absorption cushion.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection between the water inlet hose jointer and the water inlet hose
1 Push downthe slider. Plug the waterinlet hose into the jointer.
The water inlet
hose jointer
Slider
Locking level
2 Hang thelock lever onto the jointer. Release
the slider till a click sound is heard.
Check the connection between the water inlet hose jointer and the
water faucet
1.Swing the hosegently to checkif it isfastened stably.
2.After installation, openthe faucet tocheck if itleaks water.
3.Do not bendthe hose byforce.
4.Each time beforeusing, please checkif the connection
between the waterinlet hose jointerand the waterfaucet,
and the installation of the waterinlet hoseis firm, so as
to avoid droppingowing to improperinstallation.
Dismount the water inlet hose
1 Close the water faucet.
2 Press the lock lever and push down theslider. Thenpull off the
water inlet hose. If the machine is used more than once every
week, the waterinlet hose jointer can remain on the faucet to
avoid damaging the fastening screws.
Lock level
Slider
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Preparation before washing
Preparation before washing
1 Connect the water inlet hose. Open the water faucet.
2 Confirm that the washing machine is earthed reliably.
Then plug thepower plug into the receptacle. The
earthing terminal shall not link to gas pipeline and
faucet water pipeline.
3 Put downthe drain hose.
4.Slanting or uneven ground may result in unstable
working or abnormal noise. Please make the machine
stand horizontally.
Pay attention to the followings before washing
Check
if C l e a r t h e Tie the long The quantity of
When the pulsator
the laundries pocket. Take strips; fasten the laundries is running ,the
have special out the coins, the buttons; shall not be too buttons of the
requirement sand, hairpins close zippers. large. Stretch laundries may
on washing etc.
and loosen the cause noise. For
laundries before t h e s a k e o f
putting them in discretion, please
the tub.
put the laundries
with buttons into
other laundries.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put the laundries difficult to absorb water into water with hand.
d. For thelaundries with heavy soil, please first remove the dirt like mudor dust.
For the parts with heavy soil, please apply detergent on them in advance, which
can make it easier to remove the soil.
e. For thelaundries that may get lint ball and those with long fur, turn it over before
putting in.
f. Do notput the laundries polluted by chemicals into the washing machine directly.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Put in the laundries
The capacity of washing and spinning refer to the
largest weight of the standard laundries under dry
condition that can be washed or spinned in one
cycle. Washing quantityfor one cycle shall be
less than the rated capacity.
The thickness, size and type of the cloth will
influence the actual washing capacity.It is
feasible to put in suitable amount of laundries and
the laundries can be tumbled normally in washing
for one cycle.
In using water with high temperature, please pay
attention to the washing temperature limit stated
on the label of the laundries.
3 Add the detergent and softener
Inlet for concentrated washing
powder and detergent
Put the washing powder and softener into the detergent
box directly as indicated in the left figure.
After that, please close the detergent box. Refer to the
following table for the usage of the detergent: The
standard dosage of the detergent and the water
quantity
Softener inlet
Detergent box
How to use the washing powder
How to use the softener
When you use softener, the softener must be lower
than the underside of water cap.
Please often wash the detergent box, because
softener may curdle easily.
Direct dissolved in the machine
1.Fill in small quantity of water.
(Select water level 1)
2.Add the powder. Run for 30 seconds to
dissolve it completely.
3.Put in the laundries. Select suitable
water level.
The instant dissolving of the washing
powder:
How to use the whitener
Fill water to decided level. Dilute
the whitener with container. Pour
it slowly into the washing tub.
Avoid using whitener on laundries
with color or pattern as they are
prone to lose color.
The whitener shall not touch the
laundries directly.
Refer to the user's manual for the
usage and quantity of the whitener.
For powder whitener, please dissolve
it before use.
1. Prepare warm water of 30 and
container.
2. Add the powder into the container
while stirring to fully dissolve it.
The powder is more prone to pollute the
laundries than the detergent. Therefore
please use it with proper quantity.
It is suggested not to use high sudsing
detergent.
Washing powder with poor quality or long
time storage may be caked. Please pay
attention to cleaning the detergent box in time.
a
9
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Use the operation buttons
a Description of the function of the operation buttons
button
WATER INLET
Mode and meaning of the indicator
In starting the machine,it is set toCOOL
WATER automatically
Push the button toselect one from thethree
modes of COOLWATER only, both WARM
WATER andCOOL WATER, or hot wateronly.
Note that the watertemperature inside the
Flash: indicating the running mode
On: indicating the mode about to run
Flash rapidly: indicating abnormal situation
tub shall not exceed50
.
Cool water No requirement on water temperature
BALANCE DISPLAY
If the hot water temperature is too high
and needs to be mixed with cool water
Cool water
Warm water
If the bulbof the levelmeter is inside the standard circle, it indicates
that the machine is horizontal.
When the temperature of hot water is
suitable, or when you need to improve
the water temperature inside the tub
Warm water
BALANCE DISPLAY
STRONG
COOL
WATER
WATER
CURRENT
INLET
LEVEL
button
TER LEVEL
WA
Select the fuzzy program. After clothdetection, the water
level will be setto one out of4, 6, 8, and10.
If there's water inside the tub, themachine cannot detect
the cloth and willdisplay water level 6
If wet laundries areput in, it maydisplay water level 10
You canalso set water level by self.After the machine is
started, it will notdetect the cloth.
If quick program isselected, the water level will be setto 2
automatically. When level is reached, itwill perform
washing while filling water. The2 water level indicator is
on, and the 4water level indicator is flashing. When the“4”
water level is reached,it will stop fillingwater. 2 level
indicator is off,and 4 level indicatoris on. It willperform
normal washing.
CURRENT button
When the washing machine starts running, it
will set the currentautomatically.
You canselect current by selfaccording to the
actual requirement.
Please do not selectstrong current under low
water level to avoidsplashing and vibration.
In FASTand GENTLE programs, thewashing
machine will set thecurrent automatically,and
the users cannot selectcurrent in that case.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
START/PAUSE button
Digitron
After the power isswitched on, push itto start
the machine
During sensing, it displays --
During operation ofprograms, it displays the
remained time (minute)
During working, push itto pause working.
During pause, push itto resume working.
During reserve procedure, it displays the
remained reserve time (in hour)
In case of abnormal phenomenon, itdisplays
the abnormal symbol (see to Page16)
POWER ON/OFF button
Push the On/Offbutton to switchon the power.
When the poweris on, push it again to switch
off the power.
FUZZY
SOAK
WASH
RINSE
SPIN
STANDARD
NIGHT
POWER
ON/OFF
SURPLUS
GENTLE
FAST
RESERVE
HOURS LATER
START
PAUSE
SELECT
PROGRAM
RESERVE
SELECT button
Push it to select one or more programs from SOAK
WASH RINSE and SPIN
RESERVE button
PROGRAM button
The following four programsare available for your
option
Push the buttonto select washingfinishing time
between 2-24 hours.
When the RESERVEfunction is activated, the
RESERVE and TIMEREMAIN indicators areon.
The other indicatorsare off.
Standard Common washing
Night
Low noise washing during night
Gentle
FAST
Washing the woolen textiles or underwear
10-minute quick washing of laundries with light soil
Push the RESERVEbutton to displaythe reserve
mode.
Remarks: Push theOn/Off button toswitch on thepower. Ifthe washing machineis idle for5 minutes, itwill
automatically switch offthe power.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
b Steps of using the operation buttons and description of each step.
BALANCE DISPLAY
FUZZY
STRONG
SOAK
WASH
RINSE
SPIN
STANDARD
NIGHT
POWER
ON/OFF
COOL
MIN
SURPLUS
WARM
GENTLE
FAST
RESERVE
HOURS LATER
SOFT
START
PAUSE
WATER
INLET
WATER
LEVEL
SELECT
PROGRAM
CURRENT
RESERVE
POWER
ON/OFF
1 Push the POWER ON/OFF button to switch on the power.
2 Push the program button to select suitable automatic program.
After switching onthe power, the machine willset standard programautomatically. To select otherautomatic program,
push the PROGRAMbutton till the relative indicator is on.
Refer to thePROGRAM button onPage 11for the selection.
Page 11
For instance: selectQUICK program forlaundries with smallquantity and lightsoil.
FUZZY
STANDARD
In selecting the standard and night programs, the
machine will execute fuzzy program to select
NIGHT
water level and wash time according to the cloth
and weight ofthe laundries. Thefull procedure is
controlled automatically.
PROGRAM
GENTLE
FAST
SELECT
3 Push the select button to select suitable procedure.
After switching on the power, the washingmachine will set to WASH-SPIN procedure
automatically. Itis the common procedure. To select other procedures, push theSELECT button to
select one or more procedures fromSOAK, WASH, RINSEAND SPIN. Refer to PROCEDURE
SELECTION METHOD tomake selection.
Page 13
Attention
Even there's no water in thetub, a certain period
is required before spin starting.
Do not usethe SOAK programfor the woolen
textiles.
Separate the laundriesthat are notcolorfast from
other laundries in washing.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Procedure selection method
Times of pushing the
SELECT button
Contents (the lightedindicators
indicate the programs about to run)
Selected procedure
Applicable circumstance
When the common laundriesneed
washing, rinsing and spinning.
WASH - SPIN
SOAK WASH RINSE SPIN
SOAK WASH RINSE SPIN
SOAK WASH RINSE SPIN
WASH
(the washing liquid
remains in the tub)
Repeat using the washingliquid
When prevent the laundriesfrom
corrugating, and the laundriesdo not
need spinning
WASH - RINSE
(the rinsing liquid
remains in the tub)
When the laundries need rinsing
And spinning after manual washing
SOAK WASH RINSE SPIN
SOAK WASH RINSE SPIN
RINSE - SPIN
Spin
(spin after drain)
When the laundries needonly
spinning after manual washing (first
drain then spin)
The laundries are verydirty, orthe
sleeves and collars ofthe shirt are
very dirty.First soak then wash.
SOAK WASH RINSE SPIN
SOAK - SPIN
Push the SELECTbutton for 6 times, and it will resume the initial mode. It will circulate in that sequence.
The SOAK procedurecan work in cooperation with automatic programs like standard and night. Thereis
intermittent pulsator stirring during soak.
4 Push the WATER INLET button to select water inlet mode
After the poweris switched on, the washing machinewill set toCOOL WATER inlet modeautomatically. To
select WARM WATER onlyor both COOL WATER and WARM WATER, pushthe WATER INLET buttonto make
selection. See toWATER INLET in Page10 for details.
Page 10
WATER
LEVEL
5 Push the WATER LEVEL button to select suitable water level
After the power isswitched on, the washingmachine will execute fuzzyprogram automatically to detectthe cloth. After
defection, it can setthe water level automatically. To select other waterlevel, push the WATER LEVELbutton to set the
water level. Refer to WATER LEVELin Page 10 forselection.
Page 10
Page 9
6 Push the CURRENT button to select suitable water current
After the power isswitched on, the washingmachine can set thecurrent automatically according tothe laundries. If you
need to select currentby yourself, please pushthe CURRENT button.
Page 10
Refer to CURRENTin Page 10 fordetails.
RESERVE
7 Push the RESERVE button to select suitable reserve wash program
After the poweris switched on, the reserve program is set to off mode automatically. If you need to set thewashing
procedure to be finished at reserved time, please push the RESERVE buttonto set the reserve wash program. Refer to
RESERVE BUTTON inPage 11for selection.
Reserve time from 2 to 24 hours
Confirm the operation ofreserve program
When the RESERVE function is activated, the indicator of the program you have set will be
off. The RESERVE (HOUR) and TIME REMAIN indicators will be on. During reserve
procedure, you can push the RESERVE button to display the reserve mode.
To change the running program or cancel the reserve setting, you need to switch off the
power and make new selection.
The washing will be finished after 18 hours.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
START
PAUSE
8 Push the START/PAUSE button
5 Close the top lid.
6 Finish washing.
It beeps to indicatethe
finishing of washing
If you open the top lid, the machine will stop working before spinning.
The power will be switched off automatically after the finishing of the washing.
7 Disposal After Washing
Please take offthe detergent box and wash it with water
1.How to takeit off: Pullit upwards slantingly and gently.
2.How to install: Put it in from the top slantingly, thenpush
it in to theright position.
Lint filter:
1.Pull it up todismount.
2.Push it down toinstall it.
3.After washing, clean thefilter screen
Dismount
Install
Dismount and install
Clean
The filter screen islikely to be blockedby foreign
materials and influence water inlet. Please clean it
with brush frequently.
If the cabinet isdirty, wipeit with wet softcloth
Do not washwith water directly.
Wipe with neutral detergent.
Do not wipewith thinner, petrol, alcohol, etc.
Alcohol
Petrol
er
inn
Th
1.After washing, close the water faucet. (If desired, dismount the water inlet hose).
2.Do not storewater in thewashing machine for a long period. Drain the watercompletely
after each using.
3.Be sure topull off thepower plug beforemaintenance.
4.Hang up thepower cord anddrain hose.
5.Wipe off thewater drops onthe surface of the machine and inside the tub. Open the toplid
for some time (about 1 hour), then close the top lid.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble-shooting Answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns
sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special
maintenance department or after-sale service department of our company. Do not repair it by yourself.
Phenomenon
Reason
Howto solve
It rings after startingthe Reserve
function. The digitron displaysE0.
The top lid isopened.
Close the top lid.
Clean the foreign material.Push
the start button again.
The drainage cannot work, or is too slow.
The digitron displays E1 and it rings.
Is the drain hoseblocked?
After washing and rinsing,it stops
running during spinning.The
digitron displays E2 andit rings.
The top lid isnot closed.
Close the top lid.
The safety switch acts, and the
spinning cannot work (after twice
automatic imbalance revising). The
digitron displays E3 and it rings.
Reorder the laundries. Closethe top lid.
Set the washing machinehorizontally and
then open and closethe top lid once.
Are the laundries putslantingly?
Is the machine slanting?
The water inlet doesnot work, or is
too slow (cannot reach the water
level after about 15minutes). The
digitron displays E4 andit rings.
Open the water faucet. Push the
Start/Pause button again.
Clean the water inletvalve then push the
Start/Pause button again.
Is the water faucetopened, or is there
water supply failure?
Is the water inletvalve blocked?
The temperature is higher
than 75 C.
The water temperature is too high.
The digital tube displays E5, and rings.
After cooling. Press theStar/Pause knob.
Clear the foreign material.
Is there foreign materialblocking
the spray outlet?
The cascade current ispoor or
there's no cascade current.
Please use it whenthere's power supply.
Insert the power plugtightly.
Fill water to thepreset position.
Is there power failure?
Is the power pluginserted tightly?
Is the water levelreached preset
position?
Not wash
The machine
does not act.
Insert the power plugtightly.
Close the top lid.
Set the laundries flat.
Adjust the machine tobe even
Remove the foreign materials.
Reorder the laundries andclose the top lid.
Is the power pluginserted tightly?
Is the top lidclosed reliably?
Are the laundries setflat?
Is the machine slanting?
Are there any foreignmaterials?
Are the laundries putslantingly in
spinning?
Not spin
There's abnormal sound inside
the machine
Is the screw ofthe water inlet hose
jointer loose?
Fasten the screw ofthe jointer properly.
The water faucet leakswater
Is the screw ofthe water inlet hose
jointer twisted awry?
Is the power plug plugged tightly?
Is the water faucet opened?
Are the POWER ON/OFF and
Plug the power plugtightly.
Open the water faucet.
Push the power ON/OFFbutton and
START/PAUSEbutton.
No water inlet.
START/PAUSE buttons pushed down?
Common phenomena
Phenomena
Explanation
The spinning isintermittent when it starts.
It is to balancethe laundries to avoidslanting.
The cloth sensor isdetecting the cloth. Itwill start
adding water after about48 seconds.
The wash procedurepauses.
The program issetting the drain time.A certain
period is needed beforeit starts spinning.
Push the SPINbutton, but itdoesn't act.
The pulsator pauses during water filling in washing and rinsing.
It is to avoidsplashing during water filling.
It is the waterremained in the machineduring the
ex-factory performance inspection.
There may besome water flowing outof the drain
hose in the firstuse of the machine.
It is to soakthe laundries more completely.
In adding water,the pulsator performs stirringslightly
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Packing list
Name
User's manual
Quantity
One piece
The end connecting to
the washing machine
Jointer connecting
the water inlet hose
to the water faucet
Two pieces
The end connecting to
the water inlet hose jointer
Bottom plate
One piece
Tapping screws
Lint filter
Eight pieces
One piece
One set
Fuzzy computerized automatic
washing machine
Specification
1/23L, 2/30L, 3/34L, 4/40L, 5/44L,
6/49L, 7/53L, 8/57L, 9/61L, 10/66L
Water level/Water quantity (about)
Injection pressure
0.03MPa-0.78MPa
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|