OWNER’S MANUAL
LE42H330
LE46H330
LE55H330
LD42K3
LED-LCD TELEVISION
Please READ this manual carefully before
operating your TV, and retain it for future
reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning
Warning
WARNING
RISK ELECTRIC SHOCK
DO NOT OPEN
!
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
*To avoid electric hazards, it is strongly suggested that the back cover not be opened, as there is no any
accessory inside the casing.
*lf necessary, please contact authorized after-sales services.
*A lighting flash mark in a triangle: A potentially hazardous situation, which, if not avoided, could result in
serious injury by high voltage.
*An exclamation mark in a triangle: Major part or accessory of which technical specifications must be followed if
it is to be replaced.
WARNING: To avoid fire or electric hazards, never place your television receiver in an area with heavy
moisture. Attention should be paid to avoid accidental scratches or impacts onto the screen.
CAUTION:
CAUTION:
Please read this manual carefully before using your television and keep this manual in a
good place for future reference.
To achieve the best performance of your television, read this User’s Manual carefully and
properly store it for future reference.
Information of screen displays and figures in the User’s Manual may vary due to technical
innovations.
Unauthorized disassembly of this product is prohibited.
LED -LCD television Owner’s Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Important Safety Instructions
4
LED -LCD television Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
LED -LCD television Owner’s Manual
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Panel Control
Introduction
- This is a simplified representation of front panel.
- Here shown may be somewhat different from your TV.
Panel Control
LD42K3
LE42H330/LE46H330/LE55H330
Press this key to open/close signal source
options menu.
TV/AV
1
Press to adjust the volume. In the MENU screen,
VOL +/-
POWER
2
3
these buttons serve as right/left buttons.
Press to turn on and off the TV.
Press to scan through channels. To scan quickly
through channels, press and hold down either
+/- . In the MENU screen, these buttons serve
as up/down buttons.
Menu display. Press to access the on-screen
menu display.
CH +/-
MENU
4
5
6
LED -LCD television Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Panel Control
Remote Control
Battery loading
ꢂ
ꢁ
ꢀ
1. Slide open the cover of the battery compartment on
the back of the remote controller.
2. Load two 7# (AAA) alkaline batteries in the
compartment, (plus and minus poles to respective mark)
3. Replace the cover of the battery compartment.
Precautions
As strong light may interfere the signals, change your
position to operate the remote controller if the television
cannot be turned on or off as you expect.
Make sure that two AAA alkaline batteries are loaded.
The batteries must be of the same type. The batteries
must be located properly. The batteries are not
rechargeable.
Keep the remote controller away from heat source or
humid area to ensure effective performance of the
remote controller.
Make sure that there is no obstacle between the remote
controller and television set.
8
LED -LCD television Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection Options
Connection Options
Back panel connections
LD42K3
LE42H330/LE46H330/LE55H330
Connect a video cable from a computer to this
jack.
PC/DVI Audio Connect the audio L/R cables from a computer
Connect cable pr antenna signal to the TV, either
directly or through your cable box.
PC Video In
1
2
3
4
5
6
8
ANT In
.
SPDIF
W/A
Digital Audio Optical output.
9
0
In
to this jack.
For the smart comtroller.
Component
Video In
Connect a component video device to these
jacks.
Connect a USB flash drive to view videos,images
USB jack
LAN
A
B
C
D
or listen music
.
Component
Audio In
Connect the audio L/R cables from the
component video signal source to these jacks.
Connect to the internet (No available).
Connect the S-VIDEO cable from an external signal
source to this jack.
Connect a HDMI device to receive digital audio
and uncompressed digital video.
S-VIDEO IN
Headphone
HDMI1-3 In
AV OUT
Headphone audio output terminal
.
Connect the audio L/R and video cables to your
other video equipment.
AV1 In
Connect the video signal from a video device.
7
LED -LCD television Owner’s Manual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Function
Remote Control Function
- The remote control cannot be operated unless the batteries are properly loaded.
- When using the remote control, aim it at the remote control sensor on the TV.
Function introduction
Press this key to start TV from standby mode, press it again to return to standby
mode.
Press this key for quick switching of streaming media.
Refer to the Functional Description on Page 20.
Press this key to open/close signal source options menu.
Press this key for quick switching of MO-Car.
1
POWER
2
3
4
5
USB
H. LOCK
SOURCE
DSMB
Press this key to freeze the image. Press it again to return to normal screen. (Note:
Do not display a still picture for a long time to prevent the screen from burns.).
Press this key to select the screen display proportion.
Press this key to mute the sound, press it again to activate the sound. The sound
may be activated by turning the TV on again or increasing the volume.
These keys are used to select a channel.
6
7
8
9
STILL
ARC
MUTE
0-9
0
A
Press this key to return to the previous TV program(only work in the TV mode).
Used to adjust the volume when the screen menu is closed.
Used to select a TV channel when the screen options menu is closed, specifically,
press P˜ to decrease the channel and press P™ to increase the channel..
Press this key continuously to select the sound mode.
Q. VIEW
VOL+ /-
B
CH+/-
C
D
E
Sound Mode
Picture Mode
TV.MENU
Press this key continuously to select the picture mode.
Press this key to display or exit the main menu.
Press this key to display the Special Function Menu (it functions when special
modules are inserted).
F
G
D.MENU
THUMBSTICK (Up/ Allows you to navigate the on-screen menus and adjust the system settings to
Down/Left/Right) your preference.
H
I
OK
EXIT
Press this key to confirm the selection.
Clears all on-screen displays and returns to TV viewing from any menu.
Control the USB System.
ꢀ
Backward
ꢁ
Forward
Play/Pause BACK: Back REC: no available
J
K
USB
ZOOM: Press to magnify/minify an image D.CALL: Press to display program
information.
Display on/off.
TV.CALL
L
M
N
O
P
Q
R
S
T
U
No available.
TIMESHIFT
VOD
AUDIO
PAGE+
GUIDE
TV/FM
INFO
PAGE-
CH.LIST
FAV
No available.
No available.
No available.
No available.
No available.
No available.
No available.
No available.
Press this key to display the favorite program list menu.
V
No available.
STOCK
W
X
Y
Z
[
\
Displaying the sleep time.
No available.
No available.
No available.
No available.
SLEEP
INTERACTION
Fn
DDS
BUSINESS
GAME
No available.
LED -LCD television Owner’s Manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
External Equipment Connections
External Equipment Connections
Antenna Connection
- Antenna or Cable Service without a Cable Box Connections.
- For optimum picture quality, adjust antenna direction if needed.
Note:
* It is recommended that you'd better use 757 coaxial cable to remove
the disturbance caused by airwave.
* Don't bind antenna cable and electric wire together.
ꢀ
ꢀ
ꢀ
To improve picture quality in a poor signal area,
purchase and install a signal amplifier.
If the antenna needs to be split for two Tv’s, install a
"2-WaySignal Splitter" in the connections.
AT.
If the antenna is not installed properly, contact your
dealer for assistance.
Note
❏ All cables shown are not included with the TV.
10 LED -LCD television Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
External Equipment Connections
select the source, press the OK button to confirm.
Choose Your Connection
There are several ways to connect your television,
depending on the components you want to connect
and the quality of the signal you want to achieve. The
following are examples of someways to connect your TV.
Take LE42H330 as an example, Choose the connection
which is best for you.
External AV Source Setup
How to connect
•
•
Connect the audio and video cables from the
external equipment’s output jacks to the TV input
jacks, as shown in the figure.
VCR Connection
To avoid picture noise (interference), leave an adequate
distance between the VCR and TV.
When connecting the TV to external equipment,
match the jack colors (Video = yellow, Audio Left =
white, and Audio Right = red).
How to use
Connection Option 1
A
Select the input source with using the SOURCE
button on the remote control.
Set VCR output switch to channel 3 or 4 and then tune
the TV to the same channel number.
B
C
D
Press button to select the desired source.
/
ꢂꢃ
Connection Option 2
Press OK button to confirm.
A
Connect the audio and video cables from the VCR’s
output jacks to the TV input jacks, as shown in the
figure. When connecting the TV to VCR, match the
jack colors (Video = yellow, Audio Left = white, and
Audio Right = red).
Operate the corresponding external equipment.
Connecting a DVD player
B
C
Insert a video tape into the VCR and press PLAY on
the VCR. (Refer to the VCR owner’s manual.)
How to connect
A
Connect the DVD video outputs (Y, Pb/Cb, Pr/Cr)
to the COMPONENT (Y, Pb/Cb, Pr/Cr) input jacks on
the TV and connect the DVD audio outputs to the
Select the input source with using the SOURCE button
on the remote control, and then press
/
ꢂꢃ
button to
LED -LCD television Owner’s Manual 11
Download from Www.Somanuals.com. All Manuals Search And Download.
External Equipment Connections
AUDIO jacks on the TV’as shown in the figure.
C
Press Play button on external equipment for
program play.
/
How to use
A
B
Turn on the DVD player, insert a DVD.
Use the SOURCE button on the remote control,and
PC Setup
then press
mode, press the OK button to confirm.
/
button to to select COMPONENT
ꢂꢃ
How to connect
C
D
Press Play button on external equipment for
program play.
A
B
Use the TV’s PC IN port for video connections.
Refer to the DVD player’s manual for operating
instructions.
Then, make the corresponding audio connection. If
using a sound card, adjust the PC sound as required.
HDMI or DVI Setup
How to use
A
B
Turn on the PC and the TV.
To watch digitally broadcast programs, purchase and
connect a digital set-top box.
Turn on the display by pressing the POWER button
on the TV’s remote control.
How to connect
C
D
Use SOURCE on the remote control to select PC source.
•
Use the TV’s COMPONENT (Y, Pb/Cb, Pr/Cr) INPUT
jacks, VGA or HDMI port for video connections,
depending on your set-top box connections
available. Then, make the corresponding audio
connections.
Check the image on your TV. There may be noise
associated with the resolution, vertical pattern,
contrast or brightness in PC mode. If noise is
present, change the PC mode to another resolution,
change the refresh rate to another rate or adjust the
brightness and contrast on the menu until the picture
is clear. If the refresh rate of the PC graphic card
can not be changed, change the PC graphic card or
consult the manufacturer of the PC graphic card.
How to use
A
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
B
Use SOURCE on the remote contralto select PC or
HDMI (Y, Pb/Cb, Pr/Cr) mode.
12 LED -LCD television Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
External Equipment Connections
Note
❏ Component, PC, HDMI input sources cannot be
used for Monitor out.
❏ When connecting with external audio equipments,
such as amplifiers or speakers, please turn the TV
speakers off.
Power source
TO USE AC POWER SOURCE
Use the AC polarized line cord provided for operation on
AC. Insert the AC cord plug into a standard polarized AC
outlet.
Note
❏ Avoid keeping a fixed image on the TV’s screen for
along period of Time. The fixed image may become
permanently imprinted on the screen.
❏ The synchronization input form for Horizontal and
Vertical frequencies is separate.
❏ To obtain the best picture, do not play the USB,
YPbPr, HDMI or PC source at the same time.
Monitor Out Setup
The TV has a special signal output capability which
allows you to hook up a second TV or monitor.
Note
❏ Never connect the AC line cord plug to other than
the specified voltage. Use the attached power cord
only.
Connect the second TV or monitor to the TV’s AV OUT
by the tie line. See the Operating Manual of the second
TV or monitor for further details regarding that device’s
input settings.
❏ If the polarized AC cord does not fit into a non
polarized AC outlet, do not attempt to file or cut
the blade. It is the user’s responsibility to have an
electrician replace the obsolete outlet.
❏ If you cause a static discharge when touching the
unit and the unit fails to function, simply unplug
the unit from the AC outlet and plug it back in. The
unit should return to normal operation. Polarized
AC Cord Plug.
LED -LCD television Owner’s Manual 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Receiving and Playing Operations
Choose the Input source
Basic Receiving and
Change the picture source so you can watch your TV,
VCR, Cable , or any other devices that are connected to
your TV.
Playing Operations
Playing Operations
A
B
Press SOURCE button to enter the Input Source
menu and then use button to select the
desired items (ATV/DTV, AV1, AV2, Component, PC,
HDMI1, HDMI2, HDMI3).
/
ꢂꢃ
Switching ON/OFF the TV set
In the manual, the OSD (on screen display) may be
different from your TV’s because it is just an example to
help you with the TV operation.
Press OK button to confirm .
Switching ON/OFF the TV set
Picture Menu
A
First, connect power cord correctly and the power
indicator will light.
The TV menu gives you an overview of the menus you
can select.
B
C
Press POWER on the remote control again.
If you want to exchange to standing by status,
Note
please press down POWER on the remote control
❏ Depending on the input signal, one or more menu
items may not be selectable.
D
Disconnect the power supply or unplug the
television if it is intended to completely cease the
television performance.
How to select picture mode
Choose the Menu Language
The picture mode provides the pre-defined images
settings: Standard, Mild, User, Dynamic and EyeGuard
.
When you adjust your set for the first time, you must
select the language which will be used for displaying
menus and indications.
press
picture mode repeatly. Standard, Mild, User, Dynamic
and EyeGuard
button on the remote control to select the
A
B
Press MENU and
/
to select Function menu.
ꢅ
ꢄ
.
Press
/
button to select language option and
ꢂꢃ
then press OK to confirm.
C
D
Select a particular language by pressing
repeatedly.
/
ꢂꢃ
How to customize your own picture status
When you satisfied with your choice, press MENU to
return to normal viewing.
A
Press MENU button and then use
select Picture menu.
/
button to
ꢅ
ꢄ
Back light LED Four...
B
C
Press
/
button to select the desired items.,
ꢂꢃ
Surround
press OK to enter its submenu.
Prog...
DTV Manu...
Intelligent
Mode
Net
Upgrade
Press button to adjust the setting.
/
ꢂꢃ
Chinese
14 LED -LCD television Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Receiving and Playing Operations
range of 2500K~15000K from warm color to cold
color, afterwards press
benchmark is selected for adjustment, the original
adjustment data will be automatically cleared.
/
to adjust; if a different
ꢅ
ꢄ
LED
Four_DIM
Back light
Reset
Contrast
Brightness Color
Sharpness Tint
Back light
LED
Four_DIM
Palette
Prog...
DTV Manu.
Picture
Intelligent
Mode
Cool2
+50
Sound
Cool1
Channel
Standard
0
Warm1
Function
-50
Warm2
Adjust
User
Timer
Contrast
%$&.
029(
2.
MENU
OK
This will adjust the intensity of bright parts in the
picture but keep the dark parts unchanged.
Reset
Brightness
Press
/
ꢂꢃ
to select OK or Cancel..
This will adjust the light output of the complete
picture, which will mainly affect the darker areas of
the picture.
Sound menu
Color
This will adjust the saturation level of the colors to suit
your personal preference.
How to select sound mode
A
Press MENU button and then use
select Sound menu.
/
button to
ꢅ
Sharpness
ꢄ
This will adjust the sharpness of fine details in the
picture.
B
Press OK button and then use
/
ꢂꢃ
button to
select Digital tone Mode.
Note
❏ The picture options can only be adjusted in the
Back light LED Four.
User mode. The other picture modes are preset.
Tint
Prog...
Allows you to select the color mix (Tint) of the picture.
DTV Manu.
Net
Upgrade
Intelligent
Mode
Back light
Press /
ꢂꢃ
button to adjust the Backlight.
LED Four_DIM
Select the LED Fore-drive_DIM Demo or LED Fore-
drive_DIM Calibration, Press OK to set.(It's not
availabe for LD42K3)
C
Press
/
button to select the option Standard,
ꢅ
ꢄ
Music, Movie and User.
• You can also press S.MODE button on the remote
control repeatly to select the sound mode you
want. Standard, Music, Movie and User.
Palette:
Press
/
to select the Palette option, and then
ꢂꢃ
press OK to enter its submenu, and finally press
/
to select a toner pattern from six patterns
ꢅ
ꢄ
(Cool2, Cool1, Standard, Warm1, Warm2, User) to your
color preference. Normally, the Standard mode is
selected.
How to Customize your own sound
status
If the User mode is selected, press
/
to enter
ꢂꢃ
the palette menu, (as shown in the below figure),
and then press to select a benchmark in the
A
Press MENU button and then use
select Sound menu.
/
button to
ꢅ
ꢄ
/
ꢂꢃ
LED -LCD television Owner’s Manual 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Receiving and Playing Operations
B
C
Press
/
ꢂꢃ
button to select the desired items,
Return to factory default settings.
press OK to enter its submenu.
Press
/
ꢂꢃ
button to adjust the setting.
Channel menu
Display channel menu by pressing SOURCE button then
Volume
use
item.
/
ꢂꢃ
button to select the source of ATV or DTV
Press
/
ꢂꢃ
to adjust the volume of TV set.
Balance
A
B
Press MENU button and then use
select Channel menu.
/
button to
ꢅ
ꢄ
This will adjust the output of the right and left
speakers to obtain the best stereo reproduction for
your listening position.
Press button to select the desired items,
/
ꢂꢃ
press OK to enter its submenu.
The intermediate value is 0. When indication value of
balance is greater than 0,sound of the right is stronger
than the left. when indication value of balance is less
than 0,the left sound is stronger than the right sound.
Back light LED Four...
Prog...
DTV Manu...
Digital tone
This select the modes for sound reproduction dependent
on the broadcast signals or signals from external inputs
received.
Intelligent
Mode
Net
Upgrade
Select the mode of sound (User/Standard/Music/Movie).
If the User mode is selected, press
a benchmark in the range of 50~15K from bass to
/
to select
ꢂꢃ
treble, afterwards press to adjust, if a different
/
ꢅ
ꢄ
benchmark is selected for adjustment, the original
adjustment data will be automatically cleared.
Programme Edit
Back light LED Four..
You can add a label to a channel to make it easier to find.
A
Press MENU button and then use
select Channel menu.
/
button to
ꢅ
ꢄ
Manual Search
option, and finally
to select the Search
ꢂ/ꢃto start manual search. Upon finding a
Press
press
/
ꢅ
ꢄ
program, the search will automatically stop, and the
program will be stored onto the current channel.
Surroud
You may stop the search by pressing OK or MENU
.
The surround sound feature expands the audio
listening field wider and deeper to create exceptional
sound quality from the TV’s speakers.
Fine Tune
Press
then press
/
to select the Fine Tune option, and
ꢂ/ꢃto start UP or DOWN fine tuning
ꢅ
ꢄ
AVL (Automatic Volume Limit)
until obtaining a relatively good picture effect. The
fine tuning function is for the purpose of improving
picture effect through fine tuning when that of a
certain program is not good enough. Normally, the
optimal picture effect can be obtained without fine
tuning when watching TV programs, and fine tuning
is to meet the need of adjusting a certain program.
This will reduces the differences in volume level
among broadcasters.
MAXX Bass
To adjust the super bass. Press
bass off, low , high or Medium.
/
ꢂꢃ
to select super
Reset
16 LED -LCD television Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Receiving and Playing Operations
screen.
Back light LED Four...
Intelligent
Mode
Net
Upgrade
Color system
All channels now available will be automatically preset in
order .After the search has finished, the first program
Press
and then press
system.
The TV is designed with three systems for your
choice, i.e. Auto, PAL , SECAM and NTSC. Generally,
the system is set as Auto and it is not necessary to
make an adjustment. The system is normally set as
Auto during auto search.
/
to select the Color Systems option,
ꢅ
ꢄ
to select correct color
ꢂ/ꢃ
number will display on the screen. This search
automatically adds only the active channels in your area
to the TV's memory.
It deletes any channels on which there is no broadcast or
a poor signal.
Sound system
The channels found are automatically saved.
The TV is designed with four systems for your
choice, i.e. DK, M, BG and I. Generally, it is not
necessary to adjust the system. The system is
normally set as BG during auto search.
Prog. Exchange
A
Press MENU on the remote control unit or MENU on
the TV’s front panel to display main menu, and then
Skip
press
/
to select Channel menu.
When the skip is set ON, the channel will be
skipped when pressing CH ˜ or CH ™ and only can
be selected by pressing 0-9 numerical keys.
ꢅ
ꢄ
B
C
Press
to select the Prog. Exchange option,
ꢂ/ꢃ
and then press OK to enter its submenu.
If you want to recover the skipped channel
Press to select the To Channel option, and
then press
/
ꢅ
ꢄ
/
ꢂꢃ
to set the found to be exchanged to.
1. Use Direct-digit Choosing button to select the
number of the channel to be recovered.
2. Do the above steps again.
3. Press
to set Skip as Off.
ꢂ/ꢃ
Auto Tuning
A
B
C
Press MENU button and then use
select Channel menu.
/
button to
ꢅ
ꢄ
D
After adjusting the current channel and the found to
be exchanged to, press to move the cursor
to the Exchange option, and then press OK to start
exchange and exchange the program on current
channel to the channel you set for exchange.
Press
button to select Auto Tuning, then
ꢂ/ꢃ
/
ꢅ
ꢄ
press OK to enter its submenu.
Press button to select OK, press OK button
/
ꢂꢃ
to start to scan. Press MENU button to return to the
previous menu, press EXIT button to EXIT the menu
LED -LCD television Owner’s Manual 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Receiving and Playing Operations
MEMC
Function Menu
Press
/
to set ON, Demo1,Demo2 or OFF, the
ꢂꢃ
moving picture will be better when MEMC is on
function.
Function Menu Set
DSM
Press
DEMO3.
/
ꢂꢃ
to select DEMO OFF, DEMO1,DEMO2,
A
Press MENU on the remote control unit or MENU
on the TV’s front panel to display the main menu, and
Intelligent Mode
Press
then press
/
to select the Function menu.
ꢅ
ꢄ
/
to set ON /OFF/Demo, if you select ON,
ꢂꢃ
B
Press
/
to select the option to be adjusted,
ꢂꢃ
the TV set will be in the intelligent mode, if there is
no one in front of the TV for about 20 minutes, the
TV power saving state, 10 minutes latter, the TV set
automatically stand by, When people return in front
of the TV, the TV set automatically turn.(This function
is not available for LD42K3)
and then press
/
ꢂꢃ
to adjust it.
Language
Two languages (i.e. Simplified Chinese and English)
are available for your choice.
Back light LED Four...
OPC
Surround
• Press
/
to select the OPC , then press
/
to
ꢂꢃ
ꢂꢃ
Prog...
DTV Manu...
select Uesr/Dynamic/Daylight/ Normnal/Night.
• Press to select the Adjust , then press
to set 0-10.
Intelligent
Mode
Net
Upgrade
/
/
ꢂꢃ
ꢅ
ꢄ
Chinese
• Press
adjusted, and then press
OFF.
/
to select theDynamic Contral to be
ꢅ
ꢄ
/
ꢂꢃ
to select ON or
Back light LED Four...
Contrast
Brightness
Color
Sharpness Tint
Reset
Picture
Palette
OPC
Sound Volume
OPC Mode
Adjust
<
<
<
User
10
>
>
>
Menu Timeout
Programe. A
Channel
Dynamic Control
Off
Auto..
Eye Guard
Mode
Net
Upgrade
Language M
The option is for adjusting the menu display time.
Press to set the desired time (5-30s).
/
ꢂꢃ
Function
ꢀ
Image Po.. Horizont
Wertical.
Clock
Phase
Reset
Adjust
Picture Optimize
Current..
Off Time
Off Time On Channel Remind T.. Remind C..
Timer
• Press
/
to select the Picture Optimize option.
ꢅ
ꢄ
%$&.
029(
MENU
OK 2.
• Press OK to enter the submenu.
• Press to select theDCDI/Color
Management /Background to be adjusted, and
then press to select ON or OFF.
• Press
and then press
High/ Off.
/
ꢅ
ꢄ
Eye guard Mode
• Press
/
to select the Eye guard Mode option.
• Press OK to enter the submenu.
to select the Power E.G.Mode , then press
to select Standard/Eye Guard/Curtain.
to select the Change Ch.E.GI/
Watching E.G/Watching E.G.Delay to be adjusted,
and then press to select ON or OFF.
/
ꢂꢃ
ꢂꢃ
/
to select the DNR to be adjusted,
ꢅ
ꢄ
• Press
/
/
ꢂꢃ
to select Low/Middle/
ꢅ
ꢄ
/
ꢂꢃ
• Press
/
ꢅ
ꢄ
Note The Background function is not available for LD42K3.
/
ꢂꢃ
Back light LED Four...
Contrast
Brightness
Color
Sharpness Tint
Reset
Picture
Palette
Eye GuardMode
Sound Volume
PowerOn E.G.Mode
Change Ch.E.G
Watching E.G
<
<
<
<
Standard
>
>
>
Programe. A
Channel
On
Off
Eye Guard
Mode
Net
Upgrade
Language M
Watching E.G.Delay
Off
>
Function
ꢀ
Image Po.. Horizont
Wertical.
Auto..
Clock
Phase
Reset
Adjust
Current..
Off Time
Off Time On Channel Remind T.. Remind C..
Timer
%$&.
029(
MENU
OK 2.
18 LED -LCD television Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Receiving and Playing Operations
Time Menu
Net Upgrade
Press
/
to select OK or Cancel to upgrade the TV
ꢂꢃ
A
Press MENU button and then use
select Time menu.
/
button to
ꢅ
ꢄ
set by internet and flash.
B
Press
/
to select the desired option, press OK
ꢅ
ꢄ
Adjust Menu
to enter its submenu.
The TV can be used as a display, and you may adjust
relevant settings. Press SOURCE to switch the signal
input to PC mode.
A
Press MENU to display the screen main menu, and
then press to select the Adjust menu as
shown in the below figure.
/
ꢅ
ꢄ
ꢀ
ꢀ
Current Time: The current time is calculated from the
moment upon turning the TV on. At first, check whether
the time indicated on the TV's clock is consistent with the
standard time of your time zone; if not, adjust the clock as
follows:
• Press MENU on the remote control unit or MENU
on the TV’s front panel to display the main menu,
B
C
Press
Press
/
ꢂꢃ
to select the option to be adjusted.
to adjust it.
and then press
afterwards press
option, press OK to enter the submenu.
/
to select the Timer menu,
to select the Current Time
/
ꢂꢃ
ꢅ
ꢄ
/
ꢂꢃ
Image Position
This is used to adjusting H-Position and V-Position.
• Press
/
ꢂꢃ
to set hour and minute.
• Press
/
to adjust the time.
ꢅ
ꢄ
Horizontal-Size
•
After finishing time setting, press OK or MENU to
Press
/
ꢂꢃ
to adjust it(0---100).
confirm.
Vertical-Size
Press
/
ꢂꢃ
to adjust it(0---100).
Off Time/On Time: Set a time for the TV to
turn off or on.This function allows the TV to
automatically turn on or enter standby mode
upon reaching the preset time.
Auto Adjust
Vertical and Horizontal position of picture can be
adjusted in this item.
• Press OK to enter the setting screen, and then
Clock
press
press
/
to select ON or OFF, if you select ON,
to set hour and minute. ON indicates
ꢅ
ꢄ
This is used for adjusting the phase of pixel clock in PC
mode.
/
ꢂꢃ
the On/Off Time function is enabled while OFF
indicates the function is disabled.
• .After finishing time setting, press OK or MENU to
confirm.
Phase
This is used for adjusting H Position and V Position as
well as relative parameters in PC modes.
Reset
Note
Return to factory default settings.
After setting the On/Off Time function, if the TV is AC
off or forcible DC off, the function will be automatically
LED -LCD television Owner’s Manual 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Receiving and Playing Operations
cleared.
Lock Set
On channel: This function is used in combination with
the On/Off Time function. When the TV turns on upon
reaching the On time, it automatically enters the preset
channel.
Change Password
OK
off
Tuning Lock
Preset Source
Preset Prog
Source Lock
Child Lock
off
off
• Press OK first and then press
Channel or OFF.
/
ꢂꢃ
to set the On
OK
off
Max Volume
Power On Volume
Unlock
100
off
OK
Remind Time/Remind channel: The remind time and
remind channel functions allow the TV to automatically
enter the preset channel at preset time. If the TV is AC off
or forcible DC off, the preset time will be cleared.
Change Password
After entering the Lock Set menu, press
• Press MENU on the remote control unit or MENU
on the TV's front panel to display the main menu,
/
to
ꢅ
ꢄ
select the Change Password option, and then press
OK to display the Change Password menu, afterwards
enter a new 4-digit password by pressing numerical
keys and repeat entering this password once again.
If the user does not want to change the password in
halfway, he may press MENU to exit from this menu.
and then press
afterwards press
Time option.
/
to select the Timer menu,
to select the Remind
ꢅ
ꢄ
/
ꢂꢃ
• Press OK to enter the setting screen, and then
press
press
press
/
to select ON or OFF, if you select ON,
to set hour and minute, and then
to adjust time.
ꢅ
ꢄ
/
ꢂꢃ
ꢄ
Note
/
ꢅ
• After finishing time setting, press OK or MENU to
The initial password is 0000, and the password setting
will not be changed after executing the Unlock
option.
confirm
• Press
/
to select the Remind Channel
ꢂꢃ
option, and press OK first and then press
/
ꢂꢃ
Tuning Lock
to set the found
.
Press
then press
/
to select the Tuning Lock option, and
ꢅ
ꢄ
/
to set ON or OFF.
ꢂꢃ
Lock Setup
The television has the function of security default lock.
Password needs to be entered when the program lock
mode is to be set.
(If set ON, the Tuning Menu is not available in TV
mode. To make any operation related to the Tuning
Menu, it need to enter the Lock Set menu to set
Tuning Lock OFF or execute the Unlock option.)
Preset Source Setting
Preset Source may be set as Off, TV, AV,Component,
HDMI, PC and USB. When the Preset Source is set as
TV, after entering the Preset Channel menu, press
How to use the password function
/
to select the preset channel, and the channel
Press H. LOCK, the TV screen will display Enter Password
to prompt the user to enter password by pressing
corresponding numerical keys; if the password is correct,
the user enters the Lock Set menu; if incorrect, the user is
required to enter a password again.
ꢂꢃ
will be forcibly switched to the preset one upon
turning the TV on; when the Preset Source is set as
other signal sources, the TV will be forcibly switched to
the preset source upon turning on. For example, when
the Preset Source is set as YPbPr/YCbCr, the TV will be
switched to YPbPr/YCbCr upon turning on; when set as
OFF, the preset function will be closed.
If there is no operation for a few seconds, the display will
automatically disappear.
The Lock Set menu is as follows:
Preset Prog
Only when the Preset Source is set as TV can the
Preset Channel option be available. Press
select preset channels from 0-255.
/
ꢂꢃ
to
20 LED -LCD television Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Receiving and Playing Operations
Source Lock
This function is used to prohibit watching a program
from various external inputs, e.g. AV and PC, etc. Press
To watch a 3D TV
/
to select a certain option, and then press OK
ꢅ
ꢄ
to enter the submenu, press
/
to set an external
ꢂꢃ
If the TV is currently in the 2D
input lock ON or OFF. If an external input lock is set
ON, after entering this mode, the screen will display
blue background with muting and a prompt Source
Lock; during Source Lock prompt, Source Lock will
remain if there is no other display on the screen. To
watch a program from a locked external input, just
enter Source Lock submenu to set corresponding
status as OFF or execute the Unlock option in the Lock
Set menu.
mode:
Stand-by switch
Child Lock Setting
Press
press
/
to select the Child Lock option, and then
to set ON or OFF. If set ON, this control
ꢅ
ꢄ
/
ꢂꢃ
key will not respond, and the screen will display Child
Lock when the key is pressed; if no other operation is
made, the display will automatically disappear later.
To resume Child Lock function, just enter the Lock Set
menu to set Child Lock OFF or execute the Unlock
option.
Max Volume Setting
Press
then press
/
to select the Max Volume option, and
ꢅ
ꢄ
/
to freely adjust the max volume
ꢂꢃ
within the range of 0~100. After finishing the setting,
the max volume in the Volume menu will not exceed
the preset max volume; for example, if the preset
max volume is 30, the volume in the Volume menu
can not be increased any longer upon reaching 30;
if the preset max volume is less than the value in the
Volume menu, the latter will decrease along with the
decrease of preset max volume.
3D switch key
Power on Volume
Press
and then press
within the range of 0~100.
/
to select the Power on Volume option,
ꢅ
ꢄ
/
to freely adjust the volume
ꢂꢃ
Unlock Setting
Press
/
to select the Unlock option, and then
ꢅ
ꢄ
press OK to clear all the lock settings, namely set all
the lock setting options as OFF; the Preset Channel
is set as OFF and max volume returns to 100 (except
password).
A
Press the 3D switch key on the remote control
to call out the prompt menu. (See Fig. 1 below)
Advanced function
LED -LCD television Owner’s Manual 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Receiving and Playing Operations
Streaming Media Playing
System
Note
❏ The diagrams in the following section are
schematic and only for your reference. Please see
the actual product if necessary.
B
Press
/
to select the “Confirm”option, you will
ꢂꢃ
enter the interface for selecting a corresponding 3D
mode. (See Fig. 2 below)
A
Supported file formats:
• Picture: . JPEG; PNG; BMP;
*
• Music: . Mp3(8-320kbps; WMA(32-192kbps);
*
AAC(16-576kbps)
• Movie:
MPEG4: . avi files in accordance with Div*4. x/5. x
*
Protocol;
MPEG2: some . mpeg files;
*
MPEG1: . dat and some . mpeg files;
RealVideo
*
*
If the TV is currently in the 3D
mode:
• Text: . Txt.
*
Note
❏ Due to the particularity of file coding, some files
may be unable to be read.
A
Press the 3D switch key on the remote control to call
out the prompt menu. (See Fig. 3 below)
B
Supported equipment:
B
Press
exit.
/
ꢂꢃ
keys to exit the 3D mode or cancel the
Support the equipment that supports Mass Storage
Protocol and whose file system is FAT/NTFS/FAT16/
FAT32, such as some USB disks, mobile hard disks,
card readers, MP3 players and digital cameras.
If USB equipment could not be identified due
to unsupported file system, please format the
equipment to the above-mentioned file system;
Note
❏ When you watch a 3D TV program, please wear
and turn on 3D glasses.
❏ If the signal currently detected in the HDMI
channel is one of 3D signals specified in the
Specification HDMI1.4a, selecting the “Confirm”
option will make the TV directly switch to a
corresponding 3D mode, so the above Fig. 2 will
not appear and you needn’t choose a 3D mode.
C
The external card reader supports most of the digital
cards in the current market; the types of digital cards
that can be read are relevant to the performance
of selected card reader; you may attach standard
mobile hard disks (working voltage 5.0V, working
current not higher than 500mA); during media
playing, do not pull out storage media, otherwise it
may cause system halt, damage the files in storage
media or damage USB equipment; sometimes, the
TV may halt due to overhigh information error rate,
in which case you should restart the system; there
are a lot of nonstandard USB mobile equipment
in the market, they may not be identified when
connected to the streaming media playing system;
the above phenomena may also occur on computers
and are not the TV’s fault.
❏ In the 3D mode, the TV screen display menu can
still be called out and displayed normally.
❏ The TV doesn’t memorize the setting of 3D mode,
so it will be in the 2D mode when you turn it on
again after turning it off.
❏ In the USB mode, there are various modes of 3D
video sources. With USB signals, the 3D switch key
functions only when playing a video (film). The TV
will exit the 3D mode when playing ends or when
you manually exit the 3D mode.
D
To achieve smooth playing, ensure the following:
Advanced function
22 LED -LCD television Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Receiving and Playing Operations
• The file code rate should be lower than 300KB/S;
• Due to the limitation of USB signal transmission
distance, it is recommended not to use USB patch
cord, in case of using the cord, make sure that its
length is not over 1m;
• Use high-speed USB equipment in conformity
with USB2.0 Interface Standard; if USB equipment
in conformity with USB1.1 Interface Standard is
used, the playing may be unsmooth.
E
Although many movie files are with such postfixes as
avi and mpeg, actually there are several formats in the
files; however, the TV can only play some files in avi
and mpeg formats. Some files with the postfix "dat"
are not movie files, but data files commonly used in
computers, and they can not be played as movies.
Operating Method of Streaming
Media Menu
A
Press
/
to scroll through main menu or
ꢅ
ꢄ
submenu and select your desired option.
Start/Exit Streaming Media Playing
System
B
C
Press OK to confirm your selection.
Press REV/FWD to achieve the FF (fast forward) and
FB (fast back) of the movie or music being played.
A
Press USB on the remote control unit to select the
streaming media function. press
zmplayer, press OK to enter.
/
ꢂꢃ
to select
D
E
F
G
Press PLAY/PAUSE to pause playing, and press it
again or press OK to continue playing.
B
C
Insert USB equipment into corresponding USB
interface 2s after starting the system.
Press ZOOM to magnify pictures; in zoom mode,
press
/
ꢂꢃ
and
/
to move the picture.
ꢅ
ꢄ
After entering the system menu, press
/
on
ꢂꢃ
Press OK to display and press EXIT to exit the screen
the remote control unit to select the required USB
equipment, and then press on the remote
display information while playing.
/
ꢅ
ꢄ
Press BACK to stop playing, or return to the previous
menu, and press BACK repeatedly to return to the
main menu.
control unit to select the required file.
Playing a Picture
A
After entering USB main interface, press
select a harddisk partition, and then press
select the Picture option.
/
ꢂꢃ
to
to
/
ꢅ
ꢄ
D
E
Press OK to enter the selected file.
To exit the streaming media playing system and
watch a TV program, you must return to the
streaming media main menu at first (to protect
equipment), and then press SOURCE to select TV or
directly press USB to return to the TV mode.
B
Press OK to confirm the selection and enter the
picture playing interface.
LED -LCD television Owner’s Manual 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Receiving and Playing Operations
Press to change page, and press
D
To exit playing, just press BACK repeatedly.
C
/
/
to
ꢂꢃ
ꢂꢃ
select the picture you want to play, and then press
OK to enter the playing display interface.
Note
• Press ZOOM to magnify the picture, and then
❏ The menu display varies with the number and
names of files in your equipment.
press
• Press
• Press
/
/
/
to move the picture.
ꢂꢃ
ꢅ
ꢄ
/
to select the last or next picture.
to rotate the picture.
ꢂꢃ
/
ꢅ
ꢄ
Playing Music
A
After entering USB main interface, press
select a harddisk partition, and then press
select the Music option.
/
ꢄ
to
ꢂꢃ
/
to
to
ꢅ
PLAY/PAUSE
B
C
Press OK to confirm the selection and press
play the music of your choice.
FWD
D
To exit playing, just press BACK repeatedly.
REV
PLAY/PAUSE
Press
to control the muDsi.CcALL
you currently enjoy. In music playing, press
button to Switch Play mode of 3: repeat single
Playing a Movie
A
After entering USB main interface, press
select a harddisk partition, and then press
select the "Movie" option.
/
ꢄ
to
ꢂꢃ
/
ǃrepeat randomly
ǃrepeat all
to
ꢅ
D
To exit music playing, just press BACK repeatedly.
B
C
Press OK to confirm the selection and enter the
movie playing interface.
Press
/
to change page, and press
/
to
ꢂꢃ
ꢅ
ꢄ
select the movie you want to play, and then press
Text
OK to enter the playing display interface.
• Press
/
ꢂꢃ
to select the last or next movie.
A
After entering USB main interface, press
select a harddisk partition, and then press
select the Text option.
/
ꢄ
to
ꢂꢃ
/
to
ꢅ
B
C
Press OK to confirm the selection and enter the text
playing interface.
Press
/
/
/
to select the text you want
ꢂꢃ
ꢅ
ꢄ
to read, and then press OK to play the text reading
interface. Press to change page, and press
/
ꢅ
ꢄ
BACK to exit the reading interface.
24 LED -LCD television Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance / Troubleshooting
Note
Maintenance
❏ The red button on the control can doing some
delete. Text playback support TXT format.
Maintenance
Early malfunctions can be prevented. Careful and regular
cleaning can extend the amount of time you will have
your new TV. Be sure to turn the power off and unplug
the power cord before you begin any cleaning.
Cleaning the Screen
A
Here’s a great way to keep the dust off your screen
for a while. Wet a soft cloth in a mixture of lukewarm
water and a little fabric softener or dish washing
detergent. Wring the cloth until it’s almost dry, and
then use it to wipe the screen.
D
To exit the Text mode, just press BACK repeatedly.
Settings
B
Make sure the excess water is off the screen, and
then let it air-dry before you turn on your TV.
A
After entering USB main interface, press
/
ꢅ
to
ꢄ
select the Settings option.
Cleaning the Cabinet
B
Press OK to confirm the selection and enter the
settings selection interface, and then press
to select the required options.
/
ꢄ
ꢅ
To remove dirt or dust, wipe the cabinet with a soft, dry,
lint-free cloth. Please be sure not to use a wet cloth.
Extended Absence
If you expect to leave your TV dormant for a long time
(such as a vacation), it’s a good idea to unplug the power
cord to protect against possible damage from lightning
or power surges.
Troubleshooting
For the sake of time and cost, it is strongly
recommended that you checkout the problem by
yourself according to the instructions listed hereunder
before contacting the after-sales service for technical
assistance.
Photo Slide Time
Set the scan speed of pictures to be scanned in slide
form.
There are three options (Middle/Slow/fast). Press
/
ꢂꢃ
to select the desired option.
Movie Subtitle
Press
/
ꢂꢃ
to select "ON" or "OFF".
Problem
Possible remedies
LED -LCD television Owner’s Manual 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification
sound might be produced. These phenomena
might happen in the area 1,500 meters above the
sea level. This is resulted from difference between
air pressures inside and outside the display. This is
not a defect covered by the limited warranty.
Turn onthe power supply; Properly
plug theTV setto the powersocket;
Check to see if the power cable of other
appliance is plugged in the TV set. Make
sure that the power cable of the TV set
is properly connected.
No
picture,
no sound
Problem
Possible remedies
Specification
Basic specification and parameter
Good
picture,
no sound
Depress the volume button;
Check out theaudio frequency input signals.
Check to see if the remote controller
display receiving window are blocked
by other objects and if batteries are
properly loaded.
Power
~ 150-240V 50/60Hz
Failure of
remote
controller
Color System PAL, SECAM
Stand-by
D/K, B/G, I
Designate the item of color from the
Picture menu and depress the volume
button; Keep the display and VCR
Consumption
No color,
Video Input
USB,AV, Component, HDMI or PC,
weak color separate a reasonable space; Activate
or poor
picture
some functions to store picture
brightness; Make sure that the display
and signal source are available and
turned on.
Operating temperature range:
+5°C - +35°C Operating
humidity range: 20%-80%
Storage Temperature:
-15°C~+45°C
Storage Humidity: 5%-90%,
non-condensing
Excessive
brightness
or darkness
Adjust brightness or contrast.
Environmental
condition
Picture
too big or
small
If the storage temperature is
lower than 0 °C, please first
lays the machine aside after
in the operating temperature
environment carries on restores
2 hours, then electrifies the use
again, protects your television
not to receive the damage.
Adjust the setup of sizes.
One
speaker
failure
Balance the sound in the menu.
Slight
sound
from
It is a normal phenomenon.
display
Owner’s manual x1
Remote Control
Alkaline battery
x1
x2
Accessories
(This is only available for certain
Note
models,please refer to actual products.)
❏ Do not leave the television with static picture in an
extended period as it may result in residual image
on your television screen.
Product main size (contain stand)
Note
Power
Net
MODEL
Net Size(LxWxH)
Consumption
Weight
❏ Production of the screen requires high and precision
technologies. However, there might be some
dank or bright (red, blue or green) spots, or some
anomalistic stripes or spots. This is not defect. If the
TV set is used in an area 2,400 meters above the sea
level where the air pressure is below 750hpa, the
picture on the screen maybe affected and a muffled
LE42H330
LE46H330
LE55H330
LD42K3
110W
130W
160W
120W
1012x41x622mm
1107x55x733mm
1308x55x845mm
1021x290x704mm
15.7Kg
18.2Kg
25Kg
18.2Kg
26 LED -LCD television Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Format
1
2
3
4
480i/480p
576i/576p
720p
60
Note
❏ Design and specifications are subject to change
without notice. The dimension in this manual is a
50
50/60
50/60
approximation.
1080i/1080p
Format
Recommendatory HDTV/
SDTV(YP P /YC C ) format
b r
b r
Sequence
Number
Refresh
Frequency (Hz)
Format
1
2
3
4
480i/480p
576i/576p
720p
60
50
50/60
50/60
1080i/1080p
Recommendation PC connection
input format
sequence
number
H-Frequency
(KHz)
V-Frequency
(Hz)
Format
1
2
640*480@60Hz
800*600@60Hz
31.5
60
60
37.88
1024*768@60Hz
(Recommendatory)
3
48.36
60
Recommendation DVI connection
input format
Sequence
Resolution
Refresh Frequency (Hz)
Number
1
2
3
640*480
800*600
1024*768
60
60
60
Recommendation HDMI
connection input format
Sequence
Number
Format
Refresh Frequency (Hz)
LED -LCD television Owner’s Manual 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification
28 LED -LCD television Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Format
LED -LCD television Owner’s Manual 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification
30 LED -LCD television Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Format
LED -LCD television Owner’s Manual 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification
Specification / Format
32 LED -LCD television Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Format
LED -LCD television Owner’s Manual 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification
34 LED -LCD television Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Format
LED -LCD television Owner’s Manual 35
Download from Www.Somanuals.com. All Manuals Search And Download.
|