HP Hewlett Packard Power Supply R5500 User Manual

Overview

The ERM consists of two battery packs in a 3U chassis. The

ERM connects directly to a UPS R5500 or to another ERM. Up

to two ERM units can be connected.

HP UPS R5500 ERM

Installation Instructions

At the HP recommended 80 percent load, one ERM extends

the available UPS runtime up to 30 minutes.

For more information about any of the topics covered in this

document, see the UPS user guide located on the

documentation CD or HP website

(http://www.hp.com/go/rackandpower).

Precautions

WARNING: A risk of personal injury from

electric shock and hazardous energy levels

exists. The installation of options and routine

maintenance and service of this product

must be performed by individuals who are

knowledgeable about the procedures,

precautions, and hazards associated with AC

power products.

This symbol indicates that the ERM

exceeds the recommended weight for

one individual to handle safely.

75 kg

WARNING: To reduce the risk of

167 lb

personal injury or damage to the

equipment, observe local occupational

health and safety requirements and

guidelines for manual material

handling.

CAUTION: Always plan the rack installation so that

the heaviest item is on the bottom of the rack. Install

the heaviest item first, and continue to populate the

rack from the bottom to the top.

ERM kit contents

•

Important Safety Information guide

This document

Warranty information

Rails, with mounting hardware for square- and

round-holed racks

•

ERM

Front bezel

Rear mounting brackets, plates, and

associated hardware

June 2006 (Third Edition)

Part Number 351641-003

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Insert screws through the rack into the mounting rail and

5. Tighten the hex nuts.

the front of each mounting bracket.

3. Install cage nuts or clip nuts into the rear of the rack.

Preparing the rails for

integrated shipping

If the unit is to be shipped in an HP 9000 or

10000 series rack:

1. Remove the hex nuts, flat washers, and lock washers

from the mounting rail.

2. Install the rail reinforcement plates and tighten using the

hex nuts with captive washers included in the kit, instead

of the nuts included with the rail.

3. Install the rear mounting brackets using hex nuts. Wait

until the unit is installed and the brackets are adjusted

before tightening the nuts.

4. Insert screws through the mounting rail into the cage nuts

or clip nuts.

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Install the mounting ears on the chassis using the

Powering down the UPS

screws provided.

1. Shut down all load devices.

2. Press the Standby button to take the UPS out of Operate

mode. Power to the load receptacles ceases.

3. Disconnect the UPS from utility power.

4. Wait at least 60 seconds for the UPS internal circuitry

to discharge.

Switching off the ERM

circuit breaker

WARNING: To prevent personal injury from

electric shock or damage to the equipment,

verify that the circuit breaker is in the

Off position.

4. With one person on each side, lift the chassis to rail

level and slide the chassis on the mounting rails.

5. Attach the chassis to the rack using the supplied screws.

6. If using the rear mounting brackets, be sure that the

bracket tabs are fully inserted into the rear panel cutouts,

then tighten the brackets.

Attaching the ERM front bezel

Installing the ERM

Before installing the ERM, review and observe all warnings in

"Precautions (on page 1)."

WARNING: Uneven mechanical loading in

the rack may cause a hazardous condition.

CAUTION: Always plan the rack installation so that

the heaviest item is on the bottom of the rack. Install

the heaviest item first, and continue to populate the

rack from the bottom to the top.

1. Install the mounting rails ("Installing the mounting rails"

on page 2).

2. With one person on each side of the carton, lift the

chassis and lower it to the floor in front of the rack.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the ERM to the UPS

Configuring the UPS

After the ERMs are installed, place the UPS in Configure

mode, and use the UPS front panel controls and LED

indicators to configure the UPS for the number of attached

ERMs. Other UPS parameters that can also be configured

are the nominal utility voltage level and Site Wiring

Fault detection.

In Configure mode, the LED front panel display changes

function to enable modification of the UPS parameters. Each

LED is associated with a different parameter.

Available Parameter

settings

Associated Explanation (when LED is

LED

illuminated)

Nominal

Voltage

Setting

200/208

Nom

General

Alarm

(red)

Nominal utility voltage

level is set to 200/208

VAC (factory default for

326529-D71)

NOTE: To install a second ERM, plug the cable from

the second ERM into the socket at the rear of the first

ERM. Up to two ERM units can be connected.

220 Nom

230 Nom

Battery

(red)

Nominal utility voltage

level is set to 220 VAC

Battery

Nominal utility voltage

Fault (red) level is set to 230 VAC

(factory default for

Switching on the ERM circuit breaker

326529-B31)

240 Nom

Site

Wiring

Fault (red)

Nominal utility voltage

level is set to 240 VAC

Wiring

Fault

Setting

Wiring Fault Utility

(green)

Audible alarm sounds

when ground is missing or

line and neutral

connections are reversed

ERM

Setting

0 ERMs

1 ERM

2 ERMs

0% to

UPS is configured for no

25% load attached ERMs (factory

(green)

default)

26% to

50% load attached ERM

(green)

UPS is configured for 1

51% to

UPS is configured for 2

75% load attached ERMs

(green)

Charging the ERM batteries

Connect the UPS to a grounded utility power outlet. When the

UPS is plugged in, it automatically enters Standby mode and

begins charging the ERM batteries. With the UPS in Standby

mode, allow the ERM batteries to charge for at least 24 hours

before putting the UPS into service.

To change the UPS configuration parameters:

1. Place the UPS in Configure mode.

The LEDs associated with the currently configured

parameters illuminate. A flashing green cursor indicates

where you are in the configuration process as you scroll

through the available settings.

CAUTION: To ensure maximum runtime, be sure to

configure the UPS for the number of installed ERMs

using the UPS front panel controls.

2. To change the nominal voltage, press the On button to

advance the cursor to the LED associated with the

appropriate nominal voltage parameter. The selected

voltage configuration LED flashes.

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Press the Standby button to select the nominal voltage

configuration. The LED associated with the old input

voltage parameter turns off, and the LED associated with

the new input voltage parameter illuminates solid green.

UPS front panel LED indicators

NOTE: Only one nominal utility voltage can be

configured. When setting voltage configuration

parameters, selecting an On value for any one

parameter automatically sets the other possibilities

to Off.

4. To enable the Wiring Fault parameter, press the On

button to advance the cursor to the Utility LED, then press

the Standby button. The LED illuminates solid green.

This parameter is disabled by default, and should only

be enabled for line-to-neutral connections. Enabling this

feature for line-to-line power sources causes a

false alarm.

The front panel is shown with the bezel removed.

5. To configure the UPS for the number of connected ERMs,

press the On button to advance the cursor to the load

LED associated with the number of ERMs attached to

the UPS.

Item

LED description

Overload

76% to 100% load

51% to 75% load (2 ERMs)

26% to 50% load (1 ERM)

0% to 25% load (0 ERMs)

General Alarm

6. Press the Standby button to select the appropriate ERM

configuration. The associated LED illuminates

solid green.

7. To save the configuration settings and exit Configure

mode, press the Test/Alarm Reset button.

On Battery

NOTE: Configure mode times out after 2 minutes. If

the Test/Alarm Reset button has not been pressed, any

new selections are not saved.

Battery Fault

Site Wiring Fault

Utility

UPS front panel controls

Configure Mode On

For more information, see "LED and audible alarm

troubleshooting" in the user guide.

Legal notice

The information contained herein is subject to change without notice. The only

warranties for HP products and services are set forth in the express warranty

statements accompanying such products and services. Nothing herein should

be construed as constituting an additional warranty. HP shall not be liable for

technical or editorial errors or omissions contained herein.

The front panel is shown with the bezel removed.

Item Description

Function

On button

Powers up the UPS

Places the UPS in Standby mode

Standby button

Test/Alarm Reset

button

•

Silences UPS alarms

Tests the LEDs

Configure button

Places the UPS in Configure mode

Download from Www.Somanuals.com. All Manuals Search And Download.

Grizzly Power Hammer T10165 User Manual
Haier Washer HWM8000 User Manual
Hamilton Beach Cooktop Meal Maker User Manual
Healthrider Treadmill HRTL77105 User Manual
Hotpoint Electric Pressure Cooker 5TCG User Manual
HP Hewlett Packard PDAs Smartphones h4000 User Manual
Humax Car Satellite TV System LUG 17DS User Manual
Humminbird Fish Finder Wide Portrait User Manual
Hunter Fan Thermostat 47300A User Manual
IBM Laptop S30 User Manual