HP 4x Speed
CD–ROM Disk Drive
User’s Guide
R
Workstation Systems Group
Order No. A1658–90669
Edition E0895
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Preface
Audience .
Safety and Regulatory Statem.ent.s .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
v.ii .
. v.ii .
.vii.i
.vii.i
. i.x .
. ix.
. x .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Installation Notice.
Related Manuals.
Revision Histor.y .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Problems, Questions and Suggest.ion.s .
Documentation Conventions.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Chapter 1
Preparing for Installation
General Description.
Major Features of the CD-ROM. .Dri.ve .
CD-ROM Drive Environmemtal Requirem.en.ts .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.1-.2 .
.
.
.
. 1-. 3 .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1.-4.
.
.
.
.
.
.
.
.
CD-ROM Drive Physical Specificati.on.s
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.1-.5 .
.
.
.
.
Preparing to Install the CD-ROM. .Dri.ve .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1. -.6 .
.
.
.
.
.
Tools Required.
Verifying Kit Conten. ts .
Set the SCSI-2 Add.res.s .
.
.
.
.
.
.
.
.
.
.
.
.
.
. 1-. 6.
. 1.-6.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 1-. 7.
. 1.-8.
. 1.-1.0 .
1. -.13 .
. 1.-1.5 .
1.-1. 6 .
.
.
.
.
Address Jumpers.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Prepare the Syste.m .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
SingleĆEnded SCSIĆ2 Bus Configuration Cons.tra.ints.
SCSIĆ2 Bus Termination Guide.lin.es .
Power Off the Workstation and any Pe.rip.her.als.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Chapter 2
Using your CD–ROM Drive
Your CD-ROM Drive Configurat.ion.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.2-.2 .
.
.
.
SCSI ID and Device File Information for H.P-.UX. .9.0.5 .
SCSI ID and Device File Information for H.P-.UX. .10.0 .
.
.
.
.
.
.
.
.
.
.
. 2.-2.
. 2.-2.
.
.
.
.
.
.
.
.
Controls and Features of the CD-RO.M . D.riv.e .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 2.-3.
2. -.5 .
2.-5.
. 2.-6.
.
.
.
.
.
.
Using the CD-ROM D.riv.e .
Media Description.
Disc Tray Descripti.on.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Loading
a
CD-ROM Disc in
a
HorizontallyMoun.ted. .Dri.ve.
.
.
.
.
.
.
.
.
.
.
.
.2-.7 .
. 2-. 8 .
.
.
Unloading
Loading
a
a
CD-ROM Disc in
CD-ROM Disc in
CD-ROM Disc in
a
HorizontallyMoun.ted. .Dri.ve.
Vertically Mou. nt.ed . D.riv.e .
.
.
.
.
.
.
.
.
a
a
.
.
.
.
.
.
.
.
. 2-. 9.
. 2-. 10.
.
Unloading
Mounting
a
Vertically Mou. nt.ed . D.riv.e .
.
.
.
.
a
CD-ROM .Dis.c .
CD-ROM D. is.c .
Reading the Busy L.igh.t .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 2.-1.1 .
.
.
.
Unmounting
a
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 2-. 12.
.2-.14.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Chapter 3
Maintenance and Troubleshooting
Caring for the CD-ROM .Dis.cs.
Troubleshooting .
Check the Address Settings for Single-Ende.d .Dr.ive.s .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.3-.2 .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
3. -3.
.
.
.
.3-.3 .
.
.
.
.
.
.
.
.
.
.
.
.
.
Check the Hardware Installa.tion.
Recheck the Address Sett.ing.s .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
3.-6.
.3-.7 .
.3-.8 .
. 3.-1.2 .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Verify the System Operation using Suppo. rtW. av. e .
Removal And Replacement Proced.ure.s .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Field Replaceable Un.its.
Power Off the Sy.stem.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
3. -.12 .
. 3-. 12.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Removing and Replacing the CD-ROM. D. riv. e .
.
.
.
.
.
.
.
.
.
.
.
.3-.12.
.
.
.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Appendix
A
Safety and Regulatory Statements
Emissions Regulations.
Federal Communications Commission (FC. C.)
Canadian Department of Communications (C. D.C).
Emissions Regulations Complian.ce.
Acoustics .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.A-. 2 .
.
.
.
.
.
.
.
.
.
.
. A.-2.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. A.-2.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. A. -.3 .
.A-. 3 .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Regulation On Noise Declaration For Machines -3. GSGV
Electrostatic Discharge (ESD) Precaut.ion.s .
LASERTURVALLISUUS .
Laser Safety Statement (For U.S.A.. O. nl.y) .
IEC 825 Class Laser . L.abe.ls .
Warnings and Cautio.ns .
A-3
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. A-. 5.
. A. -.4 .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. A-. 5.
. A.-6.
1
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. .
. A.-7.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Appendix B SCSI Connector Pinout
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Figures
1-1. HP 4x Speed CD-ROM .Dri.ve.
1-2. HP 4x Speed CD-ROM Physical Specif.ica.tion. s .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.1-.2 .
. 1-. 2 .
.
.
.
.
.
.
.
.
.
.
.
.
.
. 1.-9.
.
.
.
1-3. SCSI-2 Address Settin.gs .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
2-1. CD-ROM Drive Controls and Fea.tur.es.
2-2. CD-ROM Disc Tr.ay.
2-3. Placing the CD-ROM Disc in the Disc Tray (Horizo. nt.aL. M. ou.nt).
2-4. Removing the CD-ROM Disc in the Disc Tray (Horizo.nta.L . M.ou.nt).
.
.
.
.
.
.
.
.
.
.
.
.
.
. 2.-3.
2. -.6 .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.2-.7 .
2. -8
.
.
.
. 2.-9.
.
2-5. Inserting
2-6. Removing
a
CD-ROM Disc (Vertical .Mo.un.t) .
.
.
.
.
.
.
.
.
.
CD-ROM Disc from the Disc Tray (V.ert.ica.l .Mo.un.t) .
.
.
.
.
.
2-10
a
.
.
.
.
Table
1-1. . Single-Ended SCSI-2 Bus Configuration Constraints (pe.r .bu.s) .
2-1. CD-ROM Drive Operating Controls and F.eat.ure. s .
B-1 . SCSI Connector Pinouts.
.
.
.
.
. 1-. 1.3 .
.2-.4 .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. B-. 1.
.
.
.
.
.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
The HP 4x Speed CD–ROM Disc Drive User’s Guide describes how to install, configure,
and use the HP 4x Speed CD–ROM Disc Drive with an HP 9000 Series 700 workstation.
We’ve organized this guide as follows:
Chapter 1
Chapter 2
Chapter 3
Describes the preparation procedures for installing the CD–ROM Disc
Drive into the system.
Describes the installation procedures for the CD–ROM Disc Drive and
how to verify the CD–ROM Disc Drive installation.
Describes what to do if you experience problems when attempting to use
the CD–ROM Disc Drive. It also explains how to check the installation of
the new CD–ROM Disc Drive.
Audience
This guide is intended for use by anyone familiar with the HP 9000 Series 700 Owner’s
Guide who wants to install and configure the CD–ROM Drive.
Safety and Regulatory Statements
See Appendix A in the back of this manual for the safety and regulatory statements that
apply to the HP 4x Speed CD–ROM Disc Drive.
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Installation Notice
Products designated in the applicable Hewlett-Packard price list as customer-installable
can be installed by computer-knowledgeable customers who carefully read and follow the
instructions provided. Customers who elect to have the product installed by our field
personnel are charged the applicable field installation charge, as covered under the
standard terms and conditions. For more information, please contact your local sales
representative.
Related Manuals
For more information, refer to the following documents:
•
•
•
•
•
•
The Owner’s Guide that came with your system
HP-UX Installing Peripherals: HP 9000 Series 700 (B2355–90006)
Using Your HP Workstation (A2615–90003)
HP Visual User Environment User’s Guide (B1171–90061)
System Administration Tasks HP 9000 Series 700 Computers (B2355–90040)
Using HP-UX (B2910–90001)
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Revision History
The revision history for each edition of the manual is listed below:
Edition
E0895
Revision History
First Printing.
Problems, Questions, and Suggestions
If you have any questions or problems with our hardware, software, or documentation,
please contact either your HP Response Center or your local HP representative.
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Documentation Conventions
Unless otherwise noted in the text, this guide uses the following symbolic conventions:
literal values
Bold words or characters in formats and command descriptions
represent commands that you must use literally. Pathnames are
also in bold.
user-supplied
values
Italic words or characters in formats and command descriptions
represent values that you must supply. Italics are also used in
text for emphasis.
screen display
Information that the system displays appears in this typeface.
Return
A rectangle with rounded corners and a key label denotes a key on
your keyboard. (In this manual we refer to the Return key. On
your keyboard the key may be labeled either Return or Enter.)
This symbol indicates the end of a chapter or part of this guide.
x
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Preparing for Installation
This document describes the HP 4x Speed CD–ROM drive, and its installation, operation
and maintenance.
This chapter introduces the CD–ROM drive and contains the following information:
•
•
•
•
General description of the CD–ROM drive
Major features of the CD–ROM drive
Preparing to install the CD–ROM drive
Power off the workstation and any peripherals.
1–1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
General Description
The HP 4x Speed CD–ROM drive is a random access, read–only, mass storage device
that uses removable CD–ROM discs. The drive contains a semiconductor laser for
reading data optically, and includes an embedded controller with a SCSI interface.
The CD–ROM drive supports the ISO 9660 and High Sierra format standards. You can
access information from the drive like any other disk drive, however, you may not write
to the drive.
Figure 1–1. HP 4x Speed CD–ROM Drive
1–2
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Major Features of the CD–ROM Drive
The CD–ROM drive offers the following features:
•
•
•
•
•
•
•
•
•
•
•
•
•
12cm/8cm discs
600 kB sustained transfer rate
Supports 1X, 2X or 4X rotational modes
190 ms random access time
150 ms random seek time
Built–in SCSI-2 controller
Electric Load/Eject tray
Emergency Eject
Remote SCSI ID jumper block
Horizontal or vertical physical orientation
Software Volume Control (L/R channel independent)
Snap–on bezel
Continuous rotary volume control for headphones
1–3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
CD–ROM Drive Environmental Requirements
The CD–ROM drive has the following environmental requirements:
•
Temperature
Operating
5 deg. C to 50 deg. C
(41 deg. F to 122 deg. F)
–10 deg. C to 60 deg. C
(14 deg. F to 140 deg. F)
Non–Operating
•
•
Altitude
Operating
Non–Operating
3000 m (10000 ft.)
12000 m (40,000 ft.)
Humidity
Operating @ 22 deg. C
Non–Operating @ 60 deg. C
8% to 80 %RH (Non–Condensing)
5% to 95 %RH (Non–Condensing)
1–4
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
CD–ROM Drive Physical Specifications
The following illustration describes the physical specifications of the CD–ROM drive.
Audio Out
SCSI ID
Mode Select
Terminator Socket
SCSI
Connector
TOP
Power
REAR
LEFT AND RIGHT SIDES
4–M3 (TAP)
4.3 cm
19.6 cm
4–M3 (TAP)
12 Location
Mounting Screws
BOTTOM
14.95 cm
Figure 1–2. HP 4x Speed CD–ROM Physical Specifications
1–5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Preparing to Install the CD–ROM Drive
The following information is provided to prepare the CD–ROM for installation.
Tools Required
The following tools are needed to install the CD–ROM drive:
•
•
#2 Phillips screwdriver
Small needle–nose pliers
Verifying Kit Contents
Verify that the kit contains one of each of the following:
•
•
•
•
•
•
CD–ROM drive (drive P/N A4325–60001)
Set of 4 screws (M4x6)
Power adapter cable
SCSI I/O cable
Static strap
HP 4x Speed CD–ROM Disk Drive User’s Guide (A1658–90669)
NOTICE: If any contents of your kit are missing, contact your sales
representative.
Minimum Requirements
Minimum requirement for the HP–UX operating system is level 9.03 for the HP 4x
Speed CD–ROM drive.
NOTICE: You must use software patch PHSS_5764 under HP–UX 9.03, 9.05
and 9.07 to run SupportWave successfully
.
1–6
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Set the SCSI–2 Address
The CD–ROM drive must have a unique SCSI–2 target address. The CD–ROM drive’s
jumpers are set, at the factory, to the SCSI–2 default address of 2 as shown in Figure 1–3.
You must also ensure that the operating mode jumpers are set for correct drive operation.
We ship the drive with the operating mode jumpers set to operate correctly with your
system. We recommend you keep the default address if possible.
CAUTION: SCSI–2 disk drives are susceptible to mechanical and electrostatic
shock. When handling the disk drives, always wear the static–
grounding wrist strap that came in the CD–ROM drive kit. Always
handle the CD–ROM drive carefully.
Electrostatic charges can damage CD–ROM drives. To prevent
such damage from occurring, observe the following precautions
during unpacking and installation:
•
•
Stand on a static–free mat.
Wear a static strap to ensure that any accumulated electrostatic charge
discharges from your body to ground.
•
•
Connect all equipment together, including the static–free mat, static
strap, routing nodes, and peripheral units.
Keep uninstalled CD–ROM drives in their protective antistatic bags.
Use the following instructions to set the SCSI–2 address jumpers on your drive:
1–7
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Address Jumpers
To set the drive’s address, use the SCSI–2 address jumpers. Perform the following steps
to set the drive’s address:
1. Attach the static–grounding wrist strap by following the instructions on the package
that contains the strap. Attach one end of the strap to the system chassis.
2. Locate the address jumpers on the rear of the CD–ROM drive, as shown in
Figure 1–3.
3. Set the drive’s SCSI–2 target address to an address that’s not used by another
SCSI–2 device. Use jumpers, as shown in Figure 1–3; use needlenose pliers to set
the jumpers.
NOTICE: Do not use SCSI–2 address 7 because the system’s SCSI–2
controller uses address 7 by default. We advise that you do not use
SCSI–2 address 6 because the root disk drive uses it.
Ensure that the SCSI–2 terminators are removed.
1–8
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
SCSI–2 Terminators
(must be removed)
Jumpers
Jumpers
Target
ID
Target
ID
0
1
4
5
6
2
Default
Default
for /root
(NOT recommended for CD–ROM drive)
3
Figure 1–3. SCSI–2 Address Settings
1–9
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Prepare the System
Perform the following steps to prepare the system for the CD–ROM drive installation:
1. Determine the existing SCSI–2 address settings currently in use on your system.
Before installing the drive, determine which SCSI–2 ID address settings are already
being used on your system by completing the following substeps:
2. If you are using HP–UX 9.05, enter the following at the prompt:
RETURN
/etc/ioscan –d scsi
After a few moments the ioscan utility lists all of the SCSI I/O devices it could find.
If there is a SCSI CD–ROM drive in the list, that listing appears similar to the fol-
lowing:
H/W Path Description
Status
====================================
2.0.1.2.0 scsi
ok(nnnnnnnn)
If you are using HP–UX 10.0, enter the following at the prompt:
RETURN
/usr/sbin/ioscan –d sdisk
1–10
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
After a few moments the ioscan utility lists all of the SCSI I/O devices it could find.
The list appears similar to the following:
H/W Path
Class
Description
============================================
bc
8
bc
I/O Adapter
8/0
ext_bus
target
GSC built–in Fast/Wide SCSI Interface
8/0.0
8/0.0.0
8/0.5
disk
target
disk
QUANTUM LPS1080WD
8/0.5.0
8/0.6
DEC
DEC
DSP3210SW
target
disk
8/0.6.0
8/12
DSP3210SW
ba
Core I/O Adapter
Built–in SCSI
8/12/5
8/12/5.2
8/12/5.2.0
8/12/5.4
8/12/5.4.0
8/12/5.6
8/12/5.6.0
10
ext_bus
target
disk.
TOSHIBA CD–ROM XM–4101TA
SEAGATE ST3600N
target
disk.
target
disk
MICROP 2112
bc
I/O Adapter
10/12
ext_bus
target
disk
GSC add–on Fast/Wide SCSI Interface
10/12.4
10/12.4.0
SEAGATE ST31200W
If ioscan does not see your CD–ROM drive it returns the following message:
ioscan: No hardware found
If you receive this message, go to Chapter 3, “Maintenance and Troubleshooting.”
1–11
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
3. Shut down the system.
If you are running HP–UX under HP VUE, shut down your system by performing
the shutdown procedure described in your Owner’s Guide which came with your
workstation.
If you are running HP–UX without HP VUE, shut down your system by typing the
following command:
RETURN
#/etc/shutdown –h
You must have superuser privileges to use the /etc/shutdown command. If you do
not have superuser privileges, contact your system administrator.
If your workstation is part of a cluster, refer to the Managing Clusters of HP 9000
Computers manual for instructions on shutting down.
1–12
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Single-Ended SCSI-2 Bus Configuration Constraints
For the single-ended SCSI-2 bus, HP-UX supports only one of each type of removable-
media disk drive (i.e., floppy disk, CD-ROM, or magneto-optical drives) and two of the
same type tape devices (i.e., 4-mm DDS tape drives or 9-track tape drives), per SCSI bus.
You may connect no more than seven SCSI-2 devices to each single-ended SCSI-2 bus.
Table 1–1 shows the configuration constraints for each single-ended SCSI-2 device type.
You may connect no more than seven SCSI-2 device IDs to each single-ended SCSI-2
bus. Some SCSI-2 devices use more than one SCSI-2 drive address. Each address must
be accounted for in the maximum number of SCSI-2 devices allowed.
CAUTION: Do not connect single-ended SCSI-2 devices to a differential
SCSI-2 bus or differential SCSI-2 devices to a single-ended SCSI-2
bus. Connecting a SCSI-2 device to the wrong SCSI-2 bus can
cause system failure.
1–13
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Table 1–1. Single-Ended SCSI-2 Bus Configuration Constraints (per bus)
Maximum Number of Each
Type of Device Allowed
Single-Ended SCSI-2 Devices
Hard Disk Drives
7
1
1
2
2
1
1
Floppy Disk Drives
CD-ROM Drives
4-mm DDS Tape Drives
9-Track Tape Drives
650-MB Magneto-Optical Drives
Magneto-Optical Autochangers (see notice below)
8-mm Cartridge Tape Subsystem
8 Serial Port Terminal Server
2
1
Maximum Number of SCSI-2 Devices (per bus)
7
NOTICE: Magneto-Optical Autochangers use more than one SCSI-2
drive address. Each address must be accounted for in the
maximum number of SCSI-2 devices allowed.
1–14
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
SCSI-2 Bus Termination Guidelines
There are certain guidelines to follow when terminating a SCSI-2 bus. These guidelines
are:
CAUTION: Unless the SCSI-2 bus is properly terminated, the bus will not
operate. Terminators provide impedance matching on SCSI-2 bus
signal lines.
•
The last device connected to the SCSI-2 bus must be terminated with a SCSI-2
terminator. Use a Hewlett-Packard K2291 50-pin low-density bail-lock active
terminator or a Hewlett-Packard C2904A high-density thumbscrew active
terminator to terminate the last SCSI-2 option device.
•
Any termination on other devices on the bus must be removed. This includes
external termination plugged into a SCSI-2 receptacle on the device, or internal
resistor packs. (Refer to peripheral device or system configuration manuals for
termination information).
1–15
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Power Off the Workstation and any Peripherals
To power off the workstation and any peripherals, perform the following steps:
1. Power off the workstation, using the power switch on the front of the workstation.
CAUTION: Do not power off your workstation without first shutting down
HP–UX. Powering off with HP–UX still running could damage the
data on the disks associated with your workstation.
If you are already at the boot–administration level (the level used to check the SCSI–2
IDs), you do not need to shut down before powering off.
If you accidentally rebooted HP–UX while determining the address settings, see “Prepare
the System,” earlier in this chapter, for instructions on shutting down HP–UX.
2. Disconnect the power cord from the rear of the workstation and the wall outlet.
3. Power off any external peripherals attached to your workstation, and unplug their
power cables from the wall outlet.
You are now ready to begin the hardware installation of your new CD–ROM drive. The
step–by–step instructions for installing the drive are found in your Owners Guide.
1–16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Using Your CD–ROM Drive
This chapter provides the following information on using your CD–ROM drive:
•
•
•
Your CD–ROM drive configuration
Controls and features of the CD–ROM drive
Using the CD–ROM drive
NOTICES: The CD–ROM drive is a read–only device. You may access files
stored on a CD–ROM disc, but you cannot write to a CD–ROM
disc.
All instructions in this chapter assume your CD–ROM drive SCSI
ID is set to 2 – the default ID set by the factory.
All SCSI devices can use the scsi device driver.
To verify HP–UX system operation, see your System’s Owners Guide
For more information on checking or reconfiguring the kernel for a device driver or file,
see the System Administration Tasks Manual: HP 9000 Series 700 Computers.
2–1
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD–ROM Drive
Your CD–ROM Drive Configuration
Your HP–UX operating system comes with preconfigured device files and drivers. If you
use these preconfigured device files and drivers, you won’t need to configure your
CD–ROM drive with the operating system.
SCSI ID and Device File Information for HP–UX 9.05
The defauilt device files for the CD–ROM drive are in the /dev/dsk or /dev/rdsk
directories. The underlined number located in the sixth position in the device file name
indicates the SCSI address used in the file. For example, the device file c201d2s0 located
in /dev/dsk was created for SCSI address 2.
SCSI ID and Device File Information for HP–UX 10.0
Default device file names for the CD–ROM is shown below.
Device
Device File Name
CD–ROM drive
/dev/[r]dsk/c#t#d#
where
c# identifies the bus address of the SCSI interface card
t# identifies the target address of the SCSI disk
d# identifies the SCSI lun address (0, except for disk arrays)
Device file names for CD_ROM drives at HP–UX 10.0 depend on the naming
conventions of the system on which you are installing.
To create your own device files, you must reconfigure your drive with the operating
system. You can use either the System Administration Manager (SAM) or HP–UX
commands to set up the kernel and device files. With each, you must perform the
following steps:
1. Check the kernel for a device driver. If the device driver is not there, you must create
one and then reconfigure the kernel.
2. Create the appropriate device files.
3. Add a CD–ROM file system (cdfs).
2–2
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD–ROM Drive
Controls and Features of the CD–ROM Drive
Figure 2–1 shows the operating controls and features of the CD–ROM drive. Table 2–1
describes each of these controls and features.
CD–ROM Disc
Loading Tray
Emergency Eject
Headphone
Jack
Volume Control
Busy Indicator
Load/Eject Button
Figure 2–1. CD–ROM Drive Controls and Features
2–3
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD–ROM Drive
Table 2–1. CD–ROM Drive Operating Controls and Features
Control/Feature
Purpose
Eject Button
Press the Eject Button to eject the disc tray. When the drive is in
use, you must unmount the disc before ejecting it. Refer to the
subsection “Unmounting a CD–ROM disc” for instructions on
umounting a disc.
Busy Indicator
The Busy Indicator lights during a data access operation and
blinks during a data transfer. The indicator stays out when there is
one of the following:
•
•
•
Defective disc
Disc insertion error (for example, an upside–down disc)
No disc present
Disc Loading Tray
Emergency Eject
Tray for loading the disc. Eject the disc tray to insert or remove a
disc. The tray does not open if the drive power is off.
By inserting the end of a paper clip, you can eject the disc tray if
the workstation does not have power.
2–4
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD–ROM Drive
Using the CD–ROM Drive
This section provides the following information about using the CD–ROM drive:
Media description
Disc tray description
•
•
•
•
•
Loading and unloading the CD–ROM disc
Mounting and unmounting a CD–ROM disc
Reading the drive’s busy light
Media Description
CD–ROM discs are identical to audio compact discs (CDs), except that they store
computer data. CD–ROM discs are 120 mm (4.7 in.) in diameter, and use one data
surface with a capacity of 600 megabytes.
2–5
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD–ROM Drive
Disc Tray Description
This CD–ROM drive is mounted either horizontally or vertically. The disc tray has three
disc holders which are used when the CD ROM drive is mounted vertically. The three
disc holders are spring loaded to hold the disc in place. When the drive is mounted
horizontally, the three disc holders are not used and are held out of the way by the three
disc holder retainers. (see Figure 2–2)
Disc Holder Retainer
DIsc Holder
DIsc Holder B
Disc Holder Retainer
A
Disc Holder C
Disc Holder Retainer
Figure 2–2. CD–ROM Disc Tray
2–6
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD–ROM Drive
Loading a CD–ROM Disc in a Horizontally Mounted Drive
This CD–ROM drive has an automatic loading/ejecting feature. To load a disc in the
CD–ROM drive, follow these steps:
1. Check that the workstation is powered on.
2. To open the Disc Tray, press and release the Load/Eject button on the CD–ROM
drive.
3. Ensure the disc holders are held away from disc by the disc holder retainers.
4. Hold the disc by the edges with the label side up and place it in the Disc Tray as
shown in Figure 2–3.
5. To close the Disc Tray, push the front of the disc tray gently towards the drive until
it closes by itself or press the Load/Eject button.
Figure 2–3. Placing the CD–ROM Disc in the Disc Tray (Horizontal Mount)
2–7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD–ROM Drive
Unloading a CD–ROM Disc in a Horizontally Mounted Drive
Perform the following steps to unload a disc from the CD–ROM drive:
1. Press the eject button to eject the disc tray from the drive. If the drive is in use, you
must unmount the disc to eject the disc tray. The emergency eject feature allows you
to eject the disc tray if the normal procedure fails. See Table 2–1.
NOTICE: You must unmount the disc before ejecting it from the drive. Refer
to the subsection, “Unmounting a CD–ROM Disc,” for instructions
on unmounting a disc.
2. Wait until the drive has fully ejected the disc tray, then remove the disc from the tray
as shown in Figure 2–4. Be careful to touch only the edges of the disc.
Figure 2–4. Removing the CD–ROM Disc From the Disc Tray (Horizontal Mount)
3. To close the Disc Tray, push the front of the disc tray gently towards the drive until
it closes by itself.
2–8
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD–ROM Drive
Loading a CD–ROM Disc in a Vertically Mounted Drive
1. Hold the disc with the label side to the left and place the edge of the disc onto disc
holders A and B as shown in Figure 2–5.
2. Press down gently against the spring tension of disc holders A and B and swing the
top of the disc in until it is held by disc holder C.
3. To close the Disc Tray, push the front of the disc tray gently towards the drive until
it closes by itself.
Disc Holder
A
Disc Holder C
Disc Holder B
Figure 2–5. Inserting a CD–ROM Disc (Vertical Mount)
2–9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD–ROM Drive
Unloading a CD–ROM Disc in a Vertically Mounted Drive
1. Press the eject button to eject the disc tray from the drive. If the drive is in use, you
must you must unmount the disc to eject the disc tray. The emergency eject feature
allows you to eject the disc tray if the normal procedure fails. See Table 2–1.
NOTICE: You must unmount the disc before ejecting it from the drive. Refer
to the subsection, “Unmounting a CD–ROM Disc,” for instructions
on unmounting a disc.
2. Press down gently against the spring tension of disc holders A and B and swing the
top of the disc away from disc holder C, as shown in Figure 2–6
3. Remove the disc from disc holders A and B.
4. To close the Disc Tray, push the front of the disc tray gently towards the drive until
it closes by itself or press the Load/Eject button.
Disc Holder
A
Disc Holder C
Disc Holder B
Figure 2–6. Removing a CD–ROM Disc from the Disc Tray (Vertical Mount)
2–10
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD–ROM Drive
Mounting a CD–ROM Disc
To access your CD–ROM drive, you must mount a CD–ROM disc every time you insert
it into the drive.
CAUTION: Failure to mount a disc may cause a system error condition and
may also require rebooting the system.
Perform the following steps to mount a disc:
1. Insert the CD–ROM disc into the disc tray, as described in “Inserting and Removing
CD–ROM Discs Into and From the Disc Tray,” earlier in this chapter.
2. Load the disc tray into the drive, as described in “Loading a CD–ROM Disc Tray,”
earlier in this chapter.
3. Using the mkdir command, create a mount directory (for example, /cdrom) to
define where to access the CD–ROM file system, as shown:
Return
mkdir /cdrom
4. Mount the CD–ROM disc every time you insert it into the drive. The mount
command uses the following syntax:
mount sfname directory –options
where
sfname is the name of the block device file associated with the drive
containing the file system to be mounted.
directory is the mount point directory in the existing file system where
the file system is to be mounted.
options are any restrictions specified by the user.
2–11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD–ROM Drive
Mount all CD–ROM discs using the mount command with –t cdfs options. The
following example uses the preconfigured block device file /dev/dsk/c201d2s0 for
the CD–ROM drive, set for default SCSI address 2, and /cdrom as the mount direc-
tory. The device
Using HP–UX 9.05
Return
/etc/mount /dev/dsk/c201d2s0 /cdrom –t cdfs
Using HP–UX 10.0
Return
/etc/mount /dev/dsk/c#t#d# /cdrom –t cdfs
c# identifies the bus address of the SCSI interface card
t# identifies the target address of the SCSI disk
d# identifies the SCSI lun address (0, except for disk arrays)
Device file names for CD_ROM drives at HP–UX 10.0 depend on the naming conven-
tions of the system on which you are installing.
5. Now you can access the CD–ROM disc as you would any other mounted file
system. Enter the following command to change your working directory to the
CD–ROM disc:
Return
cd /cdrom
Unmounting a CD–ROM Disc
You must unmount the CD–ROM disc before you eject it from the drive.
CAUTION: You must unmount the CD–ROM disc every time you unload it
from the drive. Failure to unmount a disc can cause a system error
condition and may also require rebooting the system.
NOTICE: Before you unmount a CD–ROM disc, make sure that your work-
ing directory is set to a directory other than the one under which
the disc was mounted.
2–12
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD–ROM Drive
Use the following procedure to unmount a CD–ROM disc:
1. Unmount the disc by entering the following:
Using HP–UX 9.05
Return
/etc/umount /dev/dsk/c201d2s0
Using HP–UX 10.0
Return
/etc/umount /dev/dsk/c#t#d#
2. Press the eject button on the CD–ROM drive.
3. Remove the disc from the drive.
2–13
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD–ROM Drive
Reading the Busy Light
The CD–ROM busy light shows the status of the drive during self test and during activity
with the host system.
The CD–ROM drive performs a self test when one of the following happens:
•
•
You insert a disc into the drive.
You turn on the drive with a disc already loaded.
For the self test, the busy light operates in the following sequence:
1. Light On – The busy light goes on when the disc loads into the drive.
2. Light Flashing – The light flashes 12 times while a read test is performed on the
disc.
3. Light Off – The light goes off when the self test is complete.
The busy light goes off when one of the following conditions exist:
•
•
•
•
•
Defective disc
Disc insertion error (for example, an upside–down disc)
No disc present
A CD–ROM drive power failure exists.
The drive is idle on the SCSI bus.
The busy light flashes at 3.2 second intervals when cleaning is required for either the disc
or optics.
The busy light flashes at 1.6 second intervals when playing an audio track.
The busy light stays on during normal activity with the system.
2–14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Maintenance and Troubleshooting
This chapter provides the following information on maintenance and troubleshooting
your CD–ROM drive:
•
•
•
Caring for CD–ROM discs
Troubleshooting
Removal and Replacement Procedures
3–1
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for the CD–ROM Discs
Use the following guidelines to help care for your CD–ROM discs.
•
Use CD–ROM discs in a clean environment to prevent dust particles from
scratching disc surfaces.
•
•
Store CD–ROM discs in a cool, dry place to prevent moisture and heat damage.
If the CD–ROM disc is dirty, wipe it with a soft cloth. Don’t try to clean the
surface of a CD–ROM disc with cleaning solvents, as some cleaning solvents
may damage the disc.
3–2
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you have trouble with any of these procedures for using your CD–ROM drive, see
your System Owners Guide
This chapter explains what to do if you experience problems during the configuration
process. It also explains how to run the Support Tool Manager or the Extended Self Test
to verify your system.
If you are experiencing difficulty booting the system, reconfiguring HP–UX, or using the
CD–ROM drive, complete each of the following tasks, in the order they are presented,
until you discover and correct the problem:
•
•
•
•
Check the address settings of any single–ended SCSI–2 devices.
Check that you have installed the hardware correctly.
Recheck the device list.
Run verification tests.
Check the Address Settings for Single–Ended Drives
Check the address settings of each single–ended SCSI–2 device on the bus. Make sure
that no device has the same address setting of another. If you find two devices with the
same address, change one of the devices to a different, unused address setting. To check
the address settings for each single–ended SCSI–2 device, type the following in a
terminal window or HP–UX command line:
If you are using HP–UX 9.0x, enter the following at the prompt:
RETURN
/etc/ioscan
3–3
Download from Www.Somanuals.com. All Manuals Search And Download.
A screen similar to the following appears:
H/W Path
Description
Status
====================================
1.0.0
2.0.1
graphics
scsi
ok(0x577)
ok(0x7071)
ok(0x202)
ok(0x7072)
ok(0x7073)
ok(0x7075)
ok(0x7075)
ok(0x7074)
ok(0x707c)
ok(0x101)
2.0.1.2.0 disk
2.0.2
2.0.3
2.0.4
2.0.5
2.0.6
2.0.7
lan
hil
serial
serial
parallel
scsi
2.0.7.6.0 disk
Look under the H/W Path heading for device paths beginning with the sequence 2.0.1.
The sequence 2.0.1 denotes single–ended scsi controller. The number following 2.0.1 is
the address setting for a single–ended device on that controller. For example, the listing
2.0.1.2.0 in the sample device list tells us that there is a single–ended device currently
using address 2.
3–4
Download from Www.Somanuals.com. All Manuals Search And Download.
If you are using HP–UX 10.0, enter the following at the prompt:
RETURN
/usr/sbin/ioscan –d sdisk
After a few moments the ioscan utility lists all of the SCSI I/O devices it could find.
The list appears similar to the following:
H/W Path
Class
Description
============================================
bc
8
bc
I/O Adapter
8/0
ext_bus
target
GSC built–in Fast/Wide SCSI Interface
8/0.0
8/0.0.0
8/0.5
disk
target
disk
QUANTUM LPS1080WD
8/0.5.0
8/0.6
DEC
DEC
DSP3210SW
target
disk
8/0.6.0
8/12
DSP3210SW
ba
Core I/O Adapter
Built–in SCSI
8/12/5
8/12/5.2
8/12/5.2.0
8/12/5.4
8/12/5.4.0
8/12/5.6
8/12/5.6.0
10
ext_bus
target
disk.
TOSHIBA CD–ROM XM–4101TA
SEAGATE ST3600N
target
disk.
target
disk
MICROP 2112
bc
I/O Adapter
10/12
ext_bus
target
disk
GSC add–on Fast/Wide SCSI Interface
10/12.4
10/12.4.0
SEAGATE ST31200W
3–5
Download from Www.Somanuals.com. All Manuals Search And Download.
Check the Hardware Installation
Perform the following steps to check the hardware installation:
CAUTION: The CD–ROM drive is susceptible to mechanical and electrostatic
shock. When handling the drive, always wear the static strap that
came in the CD–ROM drive kit. Always handle the drive carefully.
1. Check that the SCSI–2 terminator is connected to the single–ended SCSI–2 port on
the rear I/O panel of the system unit (if there are no external SCSI–2 devices), or
that the last external single–ended SCSI–2 device is terminated.
2. Attach the static–grounding wrist strap by following the instructions on the package
that contains the strap.
3. Shut down HP–UX.
NOTICE: If you are already at the boot administration level, you do not need
to shut down; skip this step and go on to Step 4.
If you are running HP–UX under HP VUE, shut down your system by performing
the shutdown procedure described in your Owner’s Guide which came with your
workstation.
If you are running HP–UX without HP VUE, shut down your system by typing the
following command:
RETURN
#/etc/shutdown –h
You must have superuser privileges to use the /etc/shutdown command. If you do
not have superuser privileges, contact your system administrator.
If your workstation is part of a cluster, refer to the Managing Clusters of HP 9000
Computers manual for instructions on shutting down.
4. Power off the workstation, using the power switch on the front of the workstation.
3–6
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION: Do not power off your workstation without first shutting down
HP–UX. Powering off with HP–UX still running could damage
the data on the disks associated with your workstation.
5. Remove the drive and check the jumpers, as described in Removal and Replacement
Procedures at the end of this chapter.
6. Replace the drive.
7. Check the cable connections of your CD–ROM drive. Make sure that the connectors
are aligned and seated correctly.
8. Recheck the device list (see the next section).
Recheck the Address Settings
Check the address settings again to see if the drive is now listed (see the “Check the
Address Settings” section, earlier in this chapter).
If the CD–ROM drive and all other SCSI–2 devices available to you before you installed
the CD–ROM drive are now listed, run the system verification test for your software
version, as explained in the next sections.
If the CD–ROM drive is still not listed, or one of the SCSI–2 devices available to you
before you installed the CD–ROM drive is still not listed, contact your service
representative.
3–7
Download from Www.Somanuals.com. All Manuals Search And Download.
Verify the System Operation using SupportWave
HP–UX uses a diagnostics product called SupportWave. SupportWave contains the
Support Tools Manager so that you can verify your system operation.
You can access the Support Tools Manager while in a terminal window. If you are using
HP–VUE as your interface, you can also access the Support Tools Manager through the
sys_admin directory.
NOTICE: You must use software patch PHSS_5764 under HP–UX 9.03, 9.05
and 9.07 to run SupportWave successfully
.
Three interfaces are available with the Support Tools Manager: a command line interface
(accessed through the cstm command), a menu–driven interface (accessed through the
mstm command), and the graphical user interface (accessed through the xstm
command).
For more information on SupportWave user interfaces, see the online man pages by
entering the following at a command line prompt:
RETURN
# man cstm
RETURN
# man mstm
RETURN
# man xstm
3–8
Download from Www.Somanuals.com. All Manuals Search And Download.
To run SupportWave from either HP VUE or the HP–UX command line shell, perform
the following steps:
1. To invoke the command line interface, in a terminal window or command line shell,
type the following at the #prompt:
RETURN
# cstm
The following screen appears:
********************************************************************
******
******
******
******
******
******
******
******
******
******
******
******
******
******
******
******
******
******
******
******
******
******
******
******
SUPPORT TOOLS MANAGER
Command Line Interface
Version A.00.12
Part Number B2478–10002
(C) Copyright Hewlett Packard Co. 1991, 1992
All Rights Reserved
********************************************************************
Please wait. System mapping in progress . . .
Please type HELP or ? to list available commands.
CSTM>
3–9
Download from Www.Somanuals.com. All Manuals Search And Download.
2. To verify the system operation, type the following at the CSTM> prompt:
RETURN
CSTM>verify all
Messages that are similar to the following appear:
Verification has started on device (CPU).
Verification has started on device (FPU).
Verification has started on device (0/0/0).
Verification has started on device (2/0/1.5.0).
Verification has started on device (2/0/1.6.0).
Verification has started on device (2/0/2).
CSTM>Message from (0/0/0):
This graphics test displays a number of graphics images on the screen of
the graphics device being tested. If an X server is not currently running on that display,
X Windows will be started and run for the duration of the test. The Starbase shared
library (/usr/lib/libsb.sl) should be present to run this test.
CAUTION: This test will fail if any portion of the test window is modified
or overlaid in any way.
NOTE: If a VUE login screen is currently displayed on the monitor, the test
will wait until someone logs in the HP VUE on the graphics monitor to release the lock.
The test stops if the Screen Saver times out, it runs again once the Screen is activated.
WARNING: Do not run this exerciser with any other operation.
(Type ’R’ for Ready, Type ’S’ for Skip) [R] >>
3–10
Download from Www.Somanuals.com. All Manuals Search And Download.
3. When you see the >> prompt shown above, type the following:
RETURN
R
The following messages and a graphics test window appear:
Verification of (2/0/1.5.0) has completed. Result status – (Success).
Verification of (2/0/1.6.0) has completed. Result status – (Success).
Verification of (CPU) has completed. Result status – (Success).
Verification of (FPU) has completed. Result status – (Success).
Verification of (2/0/2) has completed. Result status – (Success).
Verification of (0/0/0) has completed. Result status – (Success).
RETURN
4. To return the CSTM>prompt, press
.
5. To exit the Support Tools Manager, enter the following:
RETURN
CSTM> exit
If any tests failed, further diagnosis is necessary by qualified service personnel.
3–11
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal and Replacement Procedures
The Removal and Replacement Procedures for the CD–ROM Drive follow.
CAUTION: Electrostatic charges can damage the integrated circuits on printed
circuit boards. To prevent such damage from occurring, follow
proper ESD precautions
Field Replaceable Units
The following components are authorized for field replacement.
Description
CD–ROM Drive
Part Number
A4325–60001
Power Off the System
Before performing the Removal and Replacement Procedures, observe the following
precautions:
1. Please refer to your system’s Owner’s Guide for the procedures to power off the
system.
2. Unplug the system unit power cord and the power cords of any peripheral devices
from the power source.
3. Unplug the system unit power cord from the back of the system unit.
WARNING: Failure to properly shut down and remove power from the system
may create a personal hazard, or may result in hardware damage or
data corruption.
Removing and Replacing the CD–ROM Drive
To open your system, remove and reinstall the CD–ROM drive, refer to your system
Owners Guide. Pre–installation information is found in Chapter 1 of this document.
3–12
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
A
Safety and Regulatory Statements
This appendix contains the following safety and regulatory statements:
•
•
•
•
•
•
Emissions regulations
Emissions regulations compliance
Acoustics
Electrostatic discharge precautions
Laser Safety Statement
Warnings and cautions
A–1
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and Regulatory Statements
Emissions Regulations
Federal Communications Commission (FCC)
The Federal Communications Commission of the U.S. government regulates the radio
frequency energy emanated by computing devices through published regulations. These
regulations specify the limits of radio frequency emission to protect radio and television
reception. All HP Apollo nodes and peripherals have been tested and comply with these
limits. The FCC regulations also require that computing devices used in the U.S. display
the agency’s label and that the related documentation include the following statement:
NOTICE: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commer-
cial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to ra-
dio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
Canadian Department of Communications (CDC)
This digital apparatus does not exceed the Class A limits for radio noise emissions from
digital apparatus as set out in the Radio Interference Requirements of the Canadian De-
partment of Communications.
A–2
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and Regulatory Statements
Emissions Regulations Compliance
Any third-party I/O device installed in HP Apollo system(s) must be in accordance with
the requirements set forth in the preceding Emissions Regulations statements. In the
event that a third-party noncompliant I/O device is installed, the customer assumes all
responsibility and liability arising therefrom.
Acoustics
Regulation On Noise Declaration For Machines –3. GSGV
Lpa <70dB
Lpa <70dB
operator position
normal operation
per ISO 7779
am Arbeitsplatz
normaler Betrieb
nach DIN 45635 T.19
A–3
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and Regulatory Statements
Electrostatic Discharge (ESD) Precautions
Electrostatic charges can damage the integrated circuits on printed circuit boards. To pre-
vent such damage from occurring, observe the following precautions during board un-
packing and installation:
•
•
Stand on a static-free mat.
Wear a static strap to ensure that any accumulated electrostatic charge is dis-
charged from your body to ground.
•
Connect all equipment together, including the static-free mat, static strap, routing
nodes, and peripheral units.
•
•
Keep uninstalled printed circuit boards in their protective antistatic bags.
Handle printed circuit boards by their edges, once you have removed them from
their protective antistatic bags.
A–4
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and Regulatory Statements
LASERTURVALLISUUS LOUKAN 1 LASERLAITE KLASS 1 LASER
APPARAT
HP 4x Speed CD–ROM–lukulaite sisältää laitteensisäisen CD–ROM–yksikön, joka on
laserlaite.
Kyseinen CD–ROM–yksikkö on käyttäjän kannalta turvallinen luokan 1 laserlaite. Nor-
maalissa käytössä yksikön suojakotelo estää lasersäteen pääsyn laitteen ulkopuolelle.
CD–ROM–yksikön on tyyppihyväksynyt Suomessa laserturvallisuuden osalta Työminis-
teriön työsuojeluosasto. Laitteen turvallisuusluokka on määritetty valtioneuvoston
päätöksen N:o 472/1985 ja standardin SFS–EN 60825 (1992) mukaisesti.
Tiedot CD–ROM–yksikössä käytettävän laserdiodin säteilyominaisuuksista:
Aallonpituus 790 nm
Teho
Luokan 1 laser
1,1 µW
Laser Safety Statement (For U.S.A. Only)
The CD ROM mass–storage system is certified as a Class–1 laser product under the U.S.
Department of Health and Human services (DHHS) Radiation Performance Standard ac-
cording to the Radiation Control for Health and Safety Act of 1968.
This means that the mass–storage system does not produce hazardous laser radiation. Be-
cause laser light emitted inside the mass–storage system is completely confined within
protective housings and external covers, the laser beam cannot escape from the machine
during any phase of user operation.
A–5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and Regulatory Statements
IEC 825 Class 1
Laser Labels
CLASS 1 LASER PRODUCT
LASER KLASSE 1
A–6
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and Regulatory Statements
Warnings and Cautions
WARNING:
Removing device cover may expose sharp edges in equipment chassis. To avoid injury,
use care when installing customer add-on devices.
WARNUNG:
Das Entfernen der Geräteabdeckung legt die scharfen Kanten im Inneren des Gerätes
frei. Um Verietzungen zu vermeiden, seien Sie vorsichtig beim Einbau von
zusätzlichen Bauteilen, die vom Kunden selber eingebaut werden können.
AVERTISSEMENT:
Des bords tranchants du châssis de l’équipement peuvent être exposés quand le cache
de l’unité n’est pas en place. Pour éviter des blessures, faire très attention lors de
l’installation de modules supplémentaires par le client.
WARNING:
Disconnect power plug from wall outlet or source power before moving or removing the
device, or installing add-on components.
WARNUNG:
Entfernen Sie die Stromzuführung von der Steckdose oder der Stromquelle bevor Sie
das Gerät bewegen, abbauen, oder zusätzliche Bauteile installieren.
AVERTISSEMENT:
Débrancher la fiche de la prise de courant ou de la source d’alimentation électrique
avant de déplacer ou de retirer l’unité, ou avant d’installer des modules supplémentaires.
CAUTION:
System power cord must be plugged into an accessible dedicated ac mains receptacle.
VORSICHT:
Das System-Netzanschlußkabel muß an eine zugängliche spezielle Wechselstrom–
Hauptzuführungssteckdose angeschlossen werden.
ATTENTION:
Le fil d’alimentation électrique du système doit être branché dans une prise de courant
c.a. spécialisée accessible.
A–7
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
B
SCSI Connector Pinouts
This appendix provides a table listing the pinouts for the SCSI Connector on the CD–ROM
drive.
Table B–1. SCSI Connector Pinouts
PIN
1
2
SIGNAL
GND
DB(0)
PIN
26
27
SIGNAL
TERMPWR
GND
3
4
GND
DB(1)
28
29
GND
GND
5
6
7
8
GND
DB(2)
GND
DB(3)
GND
DB(4)
GND
DB(5)
GND
DB(6)
GND
DB(7)
GND
DB(P)
GND
GND
GND
GND
GND
GND
OPEN
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
GND
GND
–ATN
GND
GND
GND
–BSY
GND
–ACK
GND
–RST
GND
–MSG
GND
–SEL
GND
–C/D
GND
–REQ
GND
–I/O
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
B–1
Download from Www.Somanuals.com. All Manuals Search And Download.
Order Number: A1658–90669
Edition E0895
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|