IMPORTS, INC.
POWER FEEDER
MODEL G1778
INSTRUCTIONAL MANUAL
GRIZZLY IMPORTS, INC.
COPYRIGHT © 1993 BY GRIZZLY IMPORTS, INC. TX3 601207 93
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM
WITHOUT THE WRITTEN CONSENT OF GRIZZLY IMPORTS, INC.
REVISED OCTOBER, 1994
DISCONTINUED MACHINE MANUAL DISCLAIMER
THE INFORMATION IN THIS MANUAL REPRESENTS THE LAST CONFIGURATION OF THE MACHINE BEFORE IT WAS DISCONTINUED.
MACHINE CONFIGURATIONS MAY HAVE CHANGED AS PRODUCT IMPROVEMENTS WERE INCORPORATED. IF YOU OWN AN EARLIER VER-
SION OF THE MACHINE, THIS MANUAL MAY NOT EXACTLY DEPICT YOUR MACHINE . CONTACT CUSTOMER SERVICE IF YOU HAVE ANY
QUESTIONS ABOUT DIFFERENCES. PREVIOUS VERSIONS ARE NOT AVAILABLE ONLINE.
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
PAGE
I.
INTRODUCTION ......................................................................................................1
COMMENTARY........................................................................................................1
SAFETY RULES FOR ALL TOOLS........................................................................2
UNPACKING ............................................................................................................4
PIECE INVENTORY ................................................................................................4
CLEAN-UP BEFORE ASSEMBLY ..........................................................................5
ELECTRICAL SERVICE REQUIREMENTS ............................................................5
II.
III.
IV.
V.
VI.
VII.
VIII. ASSEMBLY ..............................................................................................................6
IX.
ADJUSTMENTS ......................................................................................................8
A. ROLLER PLACEMENT ............................................................................................8
B. FEED RATES ........................................................................................................10
GEARING ..............................................................................................................10
X.
XI.
MAINTENANCE......................................................................................................11
A. GEARBOX..............................................................................................................11
B. ROLLERS ..............................................................................................................11
C. CHAIN AND GEARS ..............................................................................................11
XII.
CLOSURE ..............................................................................................................11
XIII. MACHINE DATA ....................................................................................................12
XIV. WARRANTY AND RETURNS................................................................................13
XV.
PARTS LISTS AND DIAGRAMS ..........................................................................14
A. GEARBOX DIAGRAM ............................................................................................14
B. PARTS LIST – GEARBOX DIAGRAM ..................................................................15
C. COLUMN DIAGRAM ..............................................................................................16
D. PARTS LIST – COLUMN DIAGRAM ....................................................................16
E. MOTOR DIAGRAM ................................................................................................17
F. PARTS LIST – MOTOR DIAGRAM........................................................................17
COPYRIGHT © 1993 BY GRIZZLY IMPORTS, INC. TX3 601207 93
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM
WITHOUT THE WRITTEN CONSENT OF GRIZZLY IMPORTS, INC.
REVISED OCTOBER, 1994
Download from Www.Somanuals.com. All Manuals Search And Download.
I. INTRODUCTION
We are proud to offer the Model G1778 Power Feeder. The Model G1778 is part of a growing Grizzly
family of fine woodworking machinery. When used according to the guidelines set forth in this man-
ual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to
customer satisfaction.
The Model G1778 is intended for use in a home workshop or small professional shop. Its heavy-duty
1
/4
H.P. motor, combined with versatile reduction gearing and spring activated rollers, provide plenty
of power and traction even on large workpieces.
We are also pleased to provide this instructional manual with the Model G1778 Power Feeder. This
manual was written to guide you through assembly, review safety considerations and cover general
operating procedures. If you have any constructive criticisms or comments you feel we should
include in our next printing, please write us at the address below.
Manager, Technical Documentation
Grizzly Industrial, Inc.
P.O. Box 2069
Bellingham, WA 98227
Finally, we stand behind our machines. We have two excellent regional service departments at your
disposal, should the need arise. If you have any service questions or parts requests, please call or
write us at the appropriate location listed below.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone:(570) 546-9663
Fax:(800) 438-5901
E-Mail: [email protected]
II. COMMENTARY
To operate this, or any power tool, safely and efficiently, it is essential to become as familiar with its
characteristics as possible. Take as much time as necessary to become acquainted with the Model
G1778 Power Feeder. The time you invest before you begin to use this machine will be time well
spent. If you do not understand something, do not operate this machine.
The specifications, drawings and photographs illustrated in this manual represent the Model G1778,
as supplied when the manual was prepared. However, owing to Grizzly’s policy of continuous
improvement, changes to the Model G1778 may be made at any time with no obligation on the part
of Grizzly.
- 1 -
Download from Www.Somanuals.com. All Manuals Search And Download.
The information in this manual has been obtained from sources believed to be reliable and as up-to-
date as possible. We have focused primarily on the proper assembly and adjustment of your power
feeder – as well as some basic information on using the power feeder on specific machines. We
have also included some important safety measures which we believe to be essential to this
machine’s operation. While most safety measures are generally universal, Grizzly cautions that each
workshop is different and safety rules should be considered as they apply to your individual situa-
tion.
The primary function of the Model G1778 is to provide automated material handling capabilities for
your shaper or table saw. Feed speed is controlled by interchangeable gear systems which allow
you to customize the motor-to-drive wheel ratio – giving you six possible speeds to choose from,
ranging from 16 to 52 feet-per-minute (FPM).
We recommend that your keep a current copy of the Grizzly catalog for complete information regard-
ing Grizzly warranty and return policy. Should you need additional technical information relating to
this machine, parts, or general assistance, please contact the appropriate regional service depart-
ment.
We also believe that additional information sources are very important to help you realize the full
potential of your woodworking equipment. Trade journals, woodworking magazines, woodworking
clubs and your local library all excellent sources of information.
III. SAFETY RULES FOR ALL TOOLS
WARNING! As with all power tools, there is a certain amount of inherent danger associated with the
Model G1778 Power Feeder. Using the tool with respect and caution will considerably lessen the
possibility of mechanical damage or operator injury. However, if normal safety precautions are over-
looked or ignored, injury to the operator or others in the area is possible.
There are certain applications for which this tool was designed. We strongly emphasize that this tool
should never be modified and/or used for any application other than that for which it was designed.
If you are confused about any aspect of this machine, do not use it until you have resolved any
questions you might have. The following are important safety rules for all tools:
1. KNOW YOUR POWER TOOL. Read the owner’s manual carefully. Learn the tool’s applications
and limitations, as well as its particular hazards.
2. KEEP GUARDS AND INSERTS IN PLACE and in working order.
3. GROUND ALL TOOLS. If the tool is equipped with a three-prong plug, it should be plugged into
a three-hole grounded outlet. If an adapter is used to accommodate a two-prong receptacle, the
adapter plug must be attached to a known ground. Never remove the grounding prong.
4. REMOVE ADJUSTING KEYS AND WRENCHES. Make it a habit to check that keys and adjust-
ing wrenches are removed from the machine before turning it on.
5. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
6. AVOID DANGEROUS ENVIRONMENTS. Do not use power tools in damp or wet locations or
expose them to rain. Keep your work area well lighted.
- 2 -
Download from Www.Somanuals.com. All Manuals Search And Download.
7. KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe dis-
tance away from your work area.
8. MAKE WORKSHOP CHILD-PROOF with padlocks, master switches, or by removing starter
keys.
9. DO NOT FORCE TOOL. Tools work better and more safely when they are allowed to work at
their own speed.
10. USE THE RIGHT TOOL. Do not use a tool or an attachment to do a job it wasn’t intended for.
11. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, or jewelry that might
get caught in moving parts. Non-slip footwear is also recommended. Wear a hat or other pro-
tective head wear if your hair is long.
12. USE SAFETY GLASSES AND EAR PROTECTION. Also use a dust mask whenever operating
the power feeder.
13. SECURE YOUR WORK. Use clamps or a fixture to hold your work. It is safer than using your
hands and frees up both hands for operating the tool.
14. DO NOT OVERREACH. Keep proper footing and balance at all times.
15. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp and clean for best and safest per-
formance. Follow instructions for lubricating and changing accessories.
16. DISCONNECT TOOLS FROM POWER before servicing and when changing accessories, such
as spindles and inserts.
17. USE RECOMMENDED ACCESSORIES. Consult the current catalog for recommended acces-
sories. The use of improper accessories may be hazardous.
18. AVOID ACCIDENTAL STARTING. Make sure the switch is in the “OFF” position before plug-
ging in the cord.
19. NEVER STAND OR LEAN ON TOOL. Serious injury could occur if the tool is tipped or if the
abrasive surfaces are accidentally contacted.
20. CHECK DAMAGED PARTS. Before further use of the tool, any part or guard that is damaged
should be promptly repaired or replaced. Do not operate the machine until you are certain it is
in perfect running condition. Failure to follow this precaution could result in further mechanical
damage and operator injury.
21. DIRECTION OF FEED. Always feed your work against the direction of the sanding spindle.
Workpieces fed in the same direction as the spindle travel could be forced out of your control.
22. NEVER LEAVE THE TOOL RUNNING UNATTENDED - TURN POWER OFF. Do not leave the
tool until it comes to a full stop.
23. DRUGS, ALCOHOL, MEDICATION. Do not operate the tool under the influence of drugs, alco-
hol, or any medication. Never operate machinery when overly fatigued.
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
IV. UNPACKING
The Model G1778 Power Feeder is shipped from the factory in two heavy-duty cardboard packages.
Find a clear work area to open the packages and inventory their contents. Use particular care, when
unpacking the boxes, to inspect all of the parts for damage incurred during shipping.
If you find the machine is damaged after you’ve signed for delivery and the truck and driver are
already gone, you will need to file a freight claim with the carrier. Save the containers and all pack-
ing materials for inspection by the carrier or their agent. Without the packing materials, filing a freight
claim can be difficult. If you need advice regarding this situation, please call us.
CAUTION: The shipping weight of the Model G1778 Power Feeder is a hefty 86 pounds. DO NOT
over-exert yourself while unpacking or moving the shipping boxes.
V. PARTS INVENTORY
Once the Model G1778 components are unpacked from their containers, take a moment to verify
that all the necessary parts have been included. You should have:
•
•
•
•
•
•
Power Feed Unit
2 Angular Joints
Vertical Column Assembly
Horizontal Column
Leadscrew Assembly
Parts Bag
LEAD
SCREW
VERTICAL
COLUMN
ASSEMBLY
HORIZONTAL
COLUMN
ANGULAR
JOINTS
POWER
FEEDER
UNIT
TOOLS
(PARTS BAG)
BASE
GEARS
(PARTS BAG)
Figure 1
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
VI. CLEAN-UP
All of the unpainted surfaces on this machine – and a few of the painted ones – are coated with a
rust preventative oil. The coating can be removed with paint thinner (mineral spirits) and a good sup-
ply of paper towels.
DO NOT use gasoline, lacquer thinner, acetone, or other highly-flammable solvents to remove the
coating. The possibility of flash fire or explosion is far greater and they don’t work much better than
mineral sprits anyway. Don’t use chlorinated solvents, such as perchloroethelene; they will lift the
paint and ruin the Power Feeder’s finish. While you are cleaning the Power Feeder, please pay
attention to the following rules:
1. Work only in a well-ventilated area.
2. Make sure there are no sources of open flame in your work area, such as pilot lights or wood-
stoves.
3. DO NOT smoke while you’re working.
4. Dispose of soiled towels in a proper manner to avoid fire and environmental damage.
VII. ELECTRICAL SERVICE REQUIREMENTS
The Model G1778 is wired for 110/120V, single phase operation; it cannot be operated on 220/240V.
The 1/4 H.P., 1720 R.P.M. motor draws 3.8 amps. This is not a large load. However, if you operate
the power feeder on a circuit that is already close to capacity, it could overload that circuit. If an
unusual load does not exist and a power failure still occurs, have the circuit inspected by a qualified
electrician.
This equipment must be grounded. The Model G1778 is equipped with a grounded cord and plug.
Please ensure that the outlet and circuit you select is wired for 110/120V and is properly grounded.
If the circuit isn’t grounded, it will be necessary to run a separate 12 AWG copper wire from the out-
let to a known ground. If adding a new circuit, please ensure that the circuit is connected to the
grounding terminal in your electrical service panel. Under no circumstances should the grounding
pin be removed from the three pronged plug.
A 15 amp fuse or circuit breaker should be used when fusing the power feeder. Circuits rated any
higher are not adequate to protect the motor from power surges.
If you find it necessary to use an extension cord with the Model G1778, make sure the cord is rated
Hard Service (grade S) or better. Cords up to 50 feet should contain 14 AWG wire. The extension
cord must also contain a ground wire and plug pin. Always repair or replace extension cords when
they become worn or damaged.
CAUTION: In this section we have covered some basic electrical requirements for the safe opera-
tion of your G1778 Power Feeder. As with the safety rules in the preceding section, these require-
ments are not necessarily comprehensive. Be sure your electrical configuration complies with local
and state codes. If you have questions about your specific situation, feel free to call our service tech-
nicians.
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
VIII. ASSEMBLY
Most of the power feeder has been assembled at the factory. The remaining assembly requirements
should not take a large amount of time. Take a moment to examine the parts diagrams at the back
of this manual to familiarize yourself with the various parts.
Horizontal/Vertical
Handwheels
Vertical Column
Motor
Horizontal Column
Column Bracket
Horizontal/Vertical
Leadscrews
Angle Brackets
Roller
Assembly
Base
Figure 2
While the Model G1778 Power Feeder looks somewhat complicated at first, the assembly process
is really quite simple.
Start the assembly process by attaching the horizontal column, the vertical column and the hori-
zontal leadscrew. Begin by removing the base from the vertical column assembly. The base can be
removed by loosening the clamping lever attached to the side of the base. The next several steps
of the procedure are probably most easily accomplished by laying all of the parts out on a table or
workbench.
The first step of assembly requires attaching the horizontal column to the vertical column. Begin by
loosening the clamping lever on the column bracket. The horizontal column should slip easily
through the column bracket. The column must be inserted so the guide notch goes through the
bracket. Keep in mind that the notch must line up with the guide bolt on the column bracket. If you
find that you are still having trouble inserting the horizontal column into the bracket, you may need
to loosen the guide bolt.
After the horizontal column is attached to the vertical column, attach the horizontal leadscrew. See
Figure 3. The leadscrew is attached to the column bracket by screwing it into the threaded opening
just below the horizontal column. After the leadscrew has been threaded through the bracket, attach
the column cap to the end of the horizontal column.
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Three setscrews hold the column cap to the horizontal column. You will need to loosen those
setscrews to properly seat the column cap on the column. Two of the setscrews are seen in Figure
3. At this point, attach the handles to the handwheels with a 12mm open end wrench.
2.75"
3/8" (Through Bolt)
"F" Bit (Tapped)
Figure 4
Figure 3
Once the first three components are attached, snug up the guide bolt on the column bracket. The
bolt should be tight enough to keep the horizontal column from twisting in the bracket, yet loose
enough to allow for smooth column movement. Tighten the bolt in small increments and turn the
horizontal handwheel to test movement. Once you’ve found proper adjustment, you can tighten the
clamping lever.
Now that the columns are properly attached, let’s turn our attention to the power feeder’s base.
Depending on what machine you intend to install the Model G1778 on, locate the point on your
machine’s table where installation will not affect movement of fences or other moving parts. The
base should be mounted as close to the actual work area as possible, without interfering with
machine operation. The shorter the amount of distance between the base and the rollers, the less
likely the power feeder will torque out of its desired position. You might consider mounting the base
on a stable piece of hardwood with the mounting bolts countersunk in the bottom of the wood. You
can temporarily mount the power feeder on your table with clamps to find the base location that best
suits your needs.
Using the base as your template, locate the best mounting point. Mark the outside perimeter of the
base and the locations of the four bolt holes on your table. Measure the distances of the four mount-
ing holes from the edges of the table with a tape measure or yardstick and compare those mea-
surements with the bottom of the table. Make sure the mounting holes will not align with cast braces
on the underside of the table. The proper drilling pattern, as shown in Figure 4, features 4 holes at
3
23/4" distance. The holes should be drilled at /8" if you intend to attach the base to the table with
through bolts. If you intend to drill and tap holes for your mounting bolts, use an “F” drill bit in con-
junction with a 5/16-18 tap. When you are satisfied you have properly located the base, drill through
your table and attach the base with the fasteners you have chosen for your application.
Once the holes are drilled and the base is mounted with appropriate hardware, loosen the clamp-
ing lever on the base and attach the column assembly. Tighten the clamping lever when the
columns are in place.
The next step is to attach the angular joints to the motor and roller assembly and attach that entire
unit to the outboard end of the horizontal column. To begin, connect the two angular joints. The 45°
joint is fitted with a threaded knob which is inserted into the 90° joint. Tighten the locking lever on
the 90° joint with the two joints aligned as shown in Figure 5. Attach the motor and roller assembly
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
to the angled joints. The roller casing mounts in an identical fashion as described for the angle joints.
Attach the knob on the roller casing to the 45° angle joint and tighten the locking lever.
Once the motor and roller assembly is attached to the angle joints, attach the entire unit to the col-
umn assembly. The column clamp may need to be spread slightly to attach it to the horizontal col-
umn. Use extreme care when spreading the clamp. Too much force could break the casting.
Leading
Wheel
Trailing
Wheel
Figure 6
Figure 5
It’s essential, for proper power feeder operation, that the feed rollers be parallel to the machine’s
table. To adjust the power feeder, lower the horizontal column using the handwheel at the top of the
vertical column, until the rollers contact the table. If the rollers touch unevenly, loosen the locking
lever on the 45° angular joint and continue to lower the horizontal column until all of the rollers are
touching the table evenly. Re-tighten the locking lever.
IX. ADJUSTMENTS
The effectiveness of your Model G1778 Power Feeder depends on proper placement of the rollers
and the speed at which they turn. In this section, we will look at the the adjustments that will opti-
mize power feeder performance.
A. ROLLER PLACEMENT
If you look at the rollers, as shown in Figure 6, you will notice that the gap between the leading and
middle roller is larger than that between the middle and trailing roller. That arrangement allows you
to place the rollers so the first wheel is slightly ahead of your cutting tool, while the middle and third
wheels are behind. Thus, the rollers feed your workpiece into, through and past the cutting surface
without contact between the wheels and cutter. Positioning the roller assembly this way not only pro-
vides a consistent application of power to the workpiece, it also acts to keep your hands away from
cutting surfaces.
To position the rollers correctly:
1. Raise the horizontal column so the rollers are just above the table.
2. Swing the motor and roller assembly so the rollers are just slightly away from the cutter, with
the leading roller slightly forward of the cutting surface.
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Turn the feed rollers so they are angled just slightly toward the fence. The leading wheel should
be just about 1/4" closer to the fence than the trailing wheel.
1
1
4. Set the wheel height between /16" and /8" below the height of the material you intend to mill.
The wheels, when properly adjusted, will put consistent downward pressure on your workpiece.
See Figure 7.
Figure 8
Figure 7
The power feeder can also be set to support your work against a fence, as shown in Figure 8. As
with the previous arrangement, the rollers should be slightly angled to hold the workpiece against
your cutting surface. This arrangement is ideal for milling edges and when using the power feeder
with a jointer. When using the power feeder this way, it is essential to make sure that the fence is
fastened tightly in place. As before, you will want to set the distance between the rollers and (in this
case) the fence about 1/16" to 1/8" under the thickness of the material to be milled. When used on its
side, you will want to adjust the rollers so the leading wheel is about 1/4" closer to the table than the
trailing wheel.
There are three important factors to consider when using the power feeder with a table saw; pinch-
ing, binding and blade height. If you are ripping boards 4" or wider, place the power feeder between
the fence and blade with the rollers turned slightly toward the fence. If you are ripping materials less
than 4", set the rollers as close as possible to the fence. It is important, in this case, that you don’t
set the rollers so the waste side of your material binds or pinches the blade. The rollers should be
angled with no more than 1/8" of variation between the leading and trailing wheels.
IMPORTANT: It is essential, when ripping narrow materials, that the blade height on your table saw
be at, or just slightly below the bottom of your rollers. See Figure 9. If the material you are cutting
requires you to place the saw blade directly below you rollers, set your saw blade slightly below the
full thickness of your workpiece.
Figure 9
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
B. FEED RATES
The optimum feed rate for the Model G1778 Power Feed will vary depending on a number of fac-
tors, including; the thickness of the material to be cut, the hardness of the workpiece, the speed of
the cutting tool and the configuration of the cutting tool (number of teeth, shape of cutter, etc.
Generally, the following rules can be followed with a good level of success.
•
•
•
•
The thicker the material to be cut, the slower the feed rate.
The harder the material, the slower the feed rate.
The faster the cutter speed, the faster the feed rate.
The greater the number of teeth or cutting surfaces, the faster the feed rate.
X. GEARING
The Model G1778 Power Feed gearbox allows you to tailor your feed rate to match individual pro-
jects. Feed rates range from 16 to 52 feet-per-minute. See Figure 11. To change gears:
1. Remove the gearbox cover by unscrewing the knurled knob on the front of the power head.
2. Determine the speed you desire, based on your material and cutter configuration.
3. Locate the desired feed rate on the chart shown in Figure 11.
4. Remove the hex nuts which hold the drive gears in place. See Figure 10.
5. Remove the existing gears and replace with the new gears.
6. Replace the hex nuts and attach the drive gear cover.
Hex Nuts
Figure 10
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
XI. MAINTENANCE
A. GEARBOX
The internal gearbox holds 65cc of SAE 30W gear oil. The oil should be drained and replaced after
every 500 hours of operation. A drain plug at the bottom of the gearbox provides access for removal
of old oil. Re-fill to within 3/4" of the filler plug.
B. ROLLERS
Each of the three roller wheels is fitted with a grease fitting. Lubricate after every 200 hours of use.
C. CHAINS AND GEARS
Lubricate drive gears and chains with grease after every 200 hours of operation. Clean and lubri-
cate all the machined surfaces with light machine oil.
XII. CLOSURE
The following pages contain machine specifications, parts lists, parts diagrams and warranty and
return information for your Model G1778 Power Feeder.
Feel free to write or call us if you have questions. Our service staff will be glad to help you if you
need parts or service assistance. If you have questions or comments about this manual, please
write to our Bellingham, Washington location.
Thank you for your purchase. We sincerely appreciate your business and look forward to serving
you again.
FEED RATE
16
19
26
30
26
43
30
52
32
FEET/MIN
18
24
20
26
32
30
24
20
18
Figure 11
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
XIII. MACHINE DATA
GRIZZLY MODEL G1778 POWER FEEDER
Overall Dimensions:
Height ................................................................................................................................24"
Overall Length....................................................................................................................30"
Overall Width......................................................................................................................14"
Shipping Weight............................................................................................................85 lbs.
Net Weight ....................................................................................................................80 lbs.
Construction:
Columns ..........................................................................................................................Steel
Supports ....................................................................................................................Cast Iron
Housing............................................................................................................Cast Aluminum
Wheels (3) 11/8" x 31/8"..................................................................................Synthetic Rubber
Motor:
Type ......................................................................................TEFC Capacitor Start Induction
Horsepower ..................................................................................................................1/4 H.P.
Phase Type/Voltage..................................................................................Single Phase/110V
Cycle/RPM ..............................................................................................60 Hertz/1720 RPM
Switch ..........................................................................................................Forward/Reverse
Bearings ..............................................................................Shielded and Lubricated-For-Life
Features:
•
•
•
•
Spring Tension Rollers
Heavy-Duty Gear Reduction
Universal Positioning with Locking Handles
Six Feed Speeds
Specifications, while deemed accurate, are subject to change without notice.
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
XIV. WARRANTY AND RETURNS
LIMITED WARRANTY
Grizzly Imports, Inc. warrants every product it sells for a period of one year on all parts and one year
on all electric motors to the original purchaser from the date of purchase. This warranty does not
apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alter-
ations or lack of maintenance. This is Grizzly’s sole written warranty for any and all warranties that
may be implied by law, including any merchantability or fitness, for any particular purpose, are here-
by limited to the duration of this written warranty. We do not warrant or represent that the merchan-
dise complies with the provisions of any law or acts unless the manufacturer so warrants. In no event
shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and any
legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent,
special, or consequential damages arising from the use of our products.
To take advantage of this warranty, the product or part must be returned to either our Bellingham or
Williamsport warehouse, freight pre-paid. Proof of purchase must accompany the merchandise. The
manufacturers reserve the right to change specifications at any time as they continually strive to
achieve better quality equipment.
We make every effort to ensure that our products meet high quality and durability standards and we
hope you never need to use this warranty.
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
XV. PARTS LISTS AND DIAGRAMS
A. GEARBOX DIAGRAM
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
B. PARTS LIST – GEARBOX DIAGRAM
Ref. # Part #
Description
Cap Screw M5-0.8x20
Lock Washer 5mm
Wheel
Ref. # Part #
Description
Gear 20T
024
024
024
025
026
027
028
029
030
031
032
001 PSB15M
P1778024B
P1778024C
P1778024D
P1778025
P1778026
P1778027
P1778028
P1778029
P1778030
PR17M
PLW01M
P1778003
P1778004
P1778005
P1778006
P1778007
P1778008
P1778009
P1778010
P1778011
PLW04M
PN03M
Gear 30T
002
003
004
005
006
007
008
009
110
011
012
013
014
015
016
017
018
019
020
021
022
023
024
024
Gear 32T
Screw M4-0.7x25mm
Cover
Knob
Cover
Chain
Retaining Ring 5mm
Retaining Ring 15mm
Chain
Grease Fitting
Shaft
Bushing
Sprocket
Sprocket
Retaining Ring
Sprocket
Roller Stand
Lock Washer 8mm
Nut M8-1.25mm
Oil Plug 5/8"-18
Case
P1778032
033 P1778033
034 P1778034
035 P1778035
036 P1778036
037 P1778037
038 P1778038
Collar
Gear 24T
P1778014
P1778015
P1778016
P1778017
PK06M
Chain
Spring
Bushing
Bushing
Worm Gear
Key 5x5x10mm
Bushing
Bush Tube
Key 5x5x30mm
Shaft
PK12M
039
040
041
042
043
044
045
046
P1778019
P1778020
P1778021
PSB33M
P1778040
P1778041
P1778042
PSS04M
PN03M
O-Ring
Oil Plug Gasket
Shaft
Cover
Cap Screw M5-0.8x12
Seal 17x32x8mm
Gear 26T
Setscrew M6-1.0x12mm
Nut M10-1.5mm
P1778023
P1778024
P1778024A
PW06
Washer 1/4
"
Gear 18T
PB10M
Screw M6-1.0x25mm
- 15 -
Download from Www.Somanuals.com. All Manuals Search And Download.
C. COLUMN DIAGRAM
D. PARTS LIST – COLUMN DIAGRAM
Ref. # Part #
Description
Ref. # Part #
Description
101 P1778101
102 PN03M
Base
112
113
114
115
116
117
118
119
120
121
P1778112
PSS04M
PSS14M
PB24M
Handle
Nut M8-1.25mm
Column
Setscrew M6-1.0x12mm
Setscrew M8-1.25x12mm
Bolt M12-1.75x45mm
103 P1778103
104 P1778104
105 P1778105
106 P1778106
107 PB20M
Leadscrew
Bracket
PW01
Flat Washer 1/2
"
Bolt
PN05M
Nut M16-1.5mm
Lock Handle
Bolt M8-1.25x35mm
Flat Washer 8mm
Lock Handle
Column Cap
Handwheel
P1778118
P1778119
P1778120
PW01M
108 PW01M
109 P1778109
110 P1778110
111 P1778111
Angular Joint
Angular Joint
Flat Washer 8mm
- 16 -
Download from Www.Somanuals.com. All Manuals Search And Download.
E. MOTOR DIAGRAM
F. PARTS LIST – MOTOR DIAGRAM
Ref. # Part #
Description
Ref. # Part #
Description
201 P1778201
202 P1778202
203 P1778203
204 P1778204
205 P1778205
206 P1778206
207 P1778207
Motor
208
209
210
211
212
213
P1778208
P1778109
P1778110
P1778111
P1778212
P1778213
Screw M4.5-0.75x13mm
Cord
Switch Half
Switch
Capacitor
O-Ring
Switch Cover
Handle
Screw M3.5-0.6x13mm
Wire Clamp
Strain Relief
Grease Gun
- 17 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|