MODEL T10051
12" BENCH SHEAR
INSTRUCTIONS
1. Overloading this tool can cause injury
from flying parts if the tool breaks. Do
not exceed the tool capacities.
2. NEvER operate the bench shear with-
out the plastic safety guard in place.
4. Always chamfer and de-burr sharp
sheet metal edges before bending in
the bench hand brake. Sharp edges on
sheet metal can result in severe cuts.
5. NEvER place your hands between the
blades of the shear.
6. Always wear leather gloves and
approved safety glasses when using
this machine.
7. Inspect the bench shear for any cracked
components or loose fasteners. Correct
any problems before use. Loose hard-
ware or cracks could result in sudden,
unexpected movements during use.
8. DO NOT allow children to play with the
bench shear.
Figure 1. Model T10051.
Specifications
Maximum Cut Length..................................... 12"
Cutting Capacities (Thickness):
Steel ...................................................0.020"
Aluminum............................................0.050"
Brass .................................................. 0.025"
Weight .......................................................28 lbs.
9. If at any time you are experiencing
difficulties performing the intended
operation, STOp using the tool and
contact our Technical Support at (570)
546-9663, or ask a qualified expert how
the operation should be performed.
Damage to your eyes and hands could result
from using this tool without proper protec-
tive gear. Always wear safety glasses and
heavy gloves when operating this machine.
If you need help with your new item, call our Tech
Support at: (570) 546-9663.
CopyrighT © oCToBer, 2008 By grizzLy induSTriAL, inC.
WARNINg: NO pORTION OF THIS MANUAL MAy BE REpRODUCED IN ANy SHApE
OR FORM WITHOUT THE WRITTEN AppROvAL OF gRIzzLy INDUSTRIAL, INC.
#jB11263 prinTed in ChinA
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
1. Mark your workpiece along the line that you
Cleaning
Cleaning the Model T10051 is relatively easy.
periodically wipe down the machine to remove
dust and oil. Treat all unpainted surfaces with a
non-staining lubricant after cleaning.
want to shear.
2. Align the mark you made in Step 1 with the
shear blades.
Lubrication (Figure 6)
Lubricating the Model T10051 consists of applying
oil to the pivoting and sliding surfaces.
Injury to your hands and fingers could result
from improper use of this tool. Never place
your hand in the path of the blade while
using this tool and never use the tool with-
out the safety guard in place.
To lubricate the model T10051:
1. Apply 3-4 drops of oil to the areas indicated
in Figure 6 so that oil will penetrate between
the sliding surfaces. raise and lower the
handle several times to disperse the oil.
NOTICE
2. Wipe any excess oil from these areas to pre-
If you have never used this type of machine
or equipment before, we strongly recom-
mend that you read books, trade magazines,
or get formal training before beginning any
projects. Regardless of the content in this
section, grizzly Industrial will not be held
liable for accidents caused by lack of train-
ing.
vent dust and grime build-up.
3. use your left hand to hold the workpiece
steady on the tool base while you lower the
handle with your right hand to produce the
cut. do not reach around the blade with your
right hand to hold the workpiece.
Work Stop
The Model T10051 is equipped with a work stop
that allows you to create identical cuts in multiple
workpieces.
Figure 6. Lubrication locations (left side shown).
To use the work stop:
1. Mark your workpiece along the line that you
want to shear.
2. Align the mark you made in Step 1 with the
shear blades.
3. Slide the work stop against the workpiece
and tighten the work stop knob.
4. For the following cuts, place the workpiece on
the tool base so that it rests against the work
stop, then proceed with the cut.
-3-
T10051 14" portable Benchtop Brake
Download from Www.Somanuals.com. All Manuals Search And Download.
3. use a ball head 3mm hex wrench to adjust
the blade adjustment screws to fine-tune the
position of the fixed blade (Figure 8).
Blade Adjustments
The fixed (lower) blade on the Model T10051 is
adjustable to allow for different materials and to
compensate for wear to the blades. The blade
position is factory set and only needs to be adjust-
ed if there is excessive binding between the fixed
and moving blade or if a gap exists between the
blades that causes the workpiece to bend, rather
than shear between the blades.
—Turning the blade adjustment screw clock-
wise will move the fixed blade outward,
towards the moving blade.
—Turning the blade adjustment screw coun-
terclockwise will move the fixed blade
inward, away from the moving blade.
The ideal blade adjustment will vary depending on
the material and dimensions of your workpiece.
Above all, make sure the fixed blade is parallel
with the moving blade and contacts it evenly along
the entire width.
To adjust the blade:
1. remove the blade guard.
2. Loosen, but do not remove the four blade cap
screws (Figure 7).
Blade Adjustment
Screw
Blade Cap
Fixed Blade
Screws
Figure 8. Adjustment screw.
4. once the fixed blade is set parallel to the
moving blade, tighten the four blade cap
screws, then re-install the blade guard.
5. Test the performance of the shear on a scrap
workpiece.
Blade Adjustment
—if the results are satisfactory, no further
adjustment is necessary.
Screws
Figure 7. Blade adjustment.
—if the results are not satisfactory, repeat
Steps 1–5 until the results meet your stan-
dards.
-4-
T10051 14" portable Benchtop Brake
Download from Www.Somanuals.com. All Manuals Search And Download.
T10051 parts Breakdown
&*
*&
*%
))
,
+
&-
')
)%
)'
&.
'%
'&
'(
(,
&)
''
-
),
)&
.
)*
)+
*
)(
(-
'-
(*
(*
(
'*
)-
&+
)
((
()
'+
&%
(.
',
'
'.
(&
(%
&,
&,
(%
('
).
).
(+
Labels
&
&&
&'
&%&
&(
&%'
-5-
T10051 14" portable Benchtop Brake
Download from Www.Somanuals.com. All Manuals Search And Download.
T10051 parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
PT10051001
TABLE
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
101
102
PB126M
HEX BOLT M8-1.25 X 40
LOCK NUT M8-1.25
2
PT10051002
PT10051003
PT10051004
PT10051005
PT10051006
PT10051007
PT10051008
PT10051009
PT10051010
PT10051011
PT10051012
PT10051013
PT10051014
PT10051015
PT10051016
PT10051017
PT10051018
PB26M
FIXED BLADE BASE
MOVING BLADE BASE
MOVING BLADE
PLN04M
3
PFH43M
FLAT HD SCR M6-1 X 10
SET SCREW M10-1.5 X 16
BUTTON HD CAP SCR M5-.8 X 16
PHLP HD SCR M5-.8 X 10
LOCK NUT M10-1.5
4
PSS75M
5
BLADE BRACE
PSBS16M
PS09M
6
JOINTING PLATE (LEFT)
JOINTING PLATE (RIGHT)
FASTEN PLATE 1
FASTEN PLATE 2
BLADE PIVOT PLATE
TABLE STOP
7
PLN05M
8
PT10051035
PFH43M
BUTTON HD CAP SCR M5-.8 X 5
FLAT HD SCR M6-1 X 10
HANDLE SPACER
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
PT10051037
PT10051038
PT10051039
PW04M
BRACKET SPACER
TABLE GAUGE
PIVOT SPACER
LEG
FLAT WASHER 10MM
FLAT WASHER 6MM
WORK STOP ROD
BLADE GUARD
PW03M
HANDLE
PT10051042
PT10051043
PT10051044
PB126M
FIXED BLADE
SPECIAL BOLT M10-1.5 X 30
KNOB M8-1.25 X 25
L-BRACKET
BUTTON HD CAP SCR M10-1.5 X 40
HEX BOLT M8-1.25 X 30
LOCK NUT M10-1.5
LOCK NUT M8-1.25
LOCK NUT M6-1
HEX BOLT M8-1.25 X 40
BLADE SPACER
PT10051046
PW01M
PLN05M
FLAT WASHER 8MM
FLAT WASHER 8MM
FLAT WASHER 5MM
HANDLE GRIP
PLN04M
PW01M
PLN03M
PW02M
PT10051023
PSB38M
SPECIAL BOLT M6-1 X 16
CAP SCREW M5-.8 X 25
HEX BOLT M6-1 X 20
HEX BOLT M10-1.5 X 40
LOCK NUT M10-1.5
PT10051050
PT10051051
PT10051101
PT10051102
WORK STOP
PB08M
BLADE DANGER LABEL
BLADE GUARD WARNING LABEL
PB31M
PLN05M
Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine
MUST maintain the original location and readability of the labels on the machine. If any label is
removed or becomes unreadable, REpLACE that label before using the machine again. Contact
-6-
T10051 14" portable Benchtop Brake
Download from Www.Somanuals.com. All Manuals Search And Download.
|