14.4V CORDLESS JIG SAW
MODEL H0601
INSTRUCTION MANUAL
Copyright © 2000 By Grizzly Industrial, Inc.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM
WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN CHINA
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous
conditions. This manual uses a series of symbols and signal words which are
intended to convey the level of importance of the safety messages. The progres-
sion of symbols is described below. Remember that safety messages by them-
selves do not eliminate danger and are not a substitute for proper accident pre-
vention measures.
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.
This symbol is used to alert the user to useful information
NOTICE
about proper operation of the equipment.
Safety Instructions For Power Tools
1. KEEP ALL SAFETY DEVICES IN
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors
should be kept a safe distance from
work area.
PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of check-
ing to see that keys and adjusting
wrenches are removed from tool
before turning on.
6. MAKE WORK SHOP CHILD
PROOF with padlocks, master
switches, or by removing starter
keys.
3. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite
accidents.
7. DON’T FORCE TOOL. It will do the
job better and safer at the rate for
which it was designed.
4. DON’T USE IN DANGEROUS
ENVIRONMENT. Don’t use power
tools in damp or wet locations, or
where any flammable or noxious
fumes may exist. Keep work area
well lighted.
8. USE RIGHT TOOL. Don’t force tool
or attachment to do a job for which it
was not designed.
-1-
H0601 14.4V Cordless Jig Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions For Power Tools
9. USE PROPER EXTENSION CORD
13. DON’T OVERREACH. Keep prop-
for the charger. Make sure your
extension cord is in good condition.
Conductor size should be in accor-
dance with the chart below. The
amperage rating should be listed on
the motor or tool nameplate. An
undersized cord will cause a drop in
line voltage resulting in loss of power
and overheating. Your extension
cord must also contain a ground wire
and plug pin. Always repair or
replace extension cords if they
become damaged.
er footing and balance at all times.
14. MAINTAIN TOOLS WITH CARE.
Keep tools sharp and clean for
best and safest performance.
Follow instructions for lubricating
and changing accessories.
15. DISCONNECT TOOLS before ser-
vicing and changing accessories,
such as blades, bits, cutters, and
the like.
16. REDUCE THE RISK OF UNIN-
TENTIONAL STARTING. Make
sure switch is in off position before
plugging in.
Minimum Gauge for Extension Cords
17. USE RECOMMENDED ACCES-
SORIES. Consult the owner’s
manual for recommended acces-
sories. The use of improper acces-
sories may cause risk of injury.
AMP
RATING
0-6
LENGTH
50ft
16
25ft
18
18
16
14
12
10
100ft
16
14
14
12
7-10
16
16
12
12
11-12
13-16
17-20
21-30
18. CHECK DAMAGED PARTS.
Before further use of the tool, a
guard or other part that is dam-
aged should be carefully checked
to determine that it will operate
properly and perform its intended
function. Check for alignment of
moving parts, binding of moving
parts, breakage of parts, mount-
ing, and any other conditions that
may affect its operation. A guard or
other part that is damaged should
be properly repaired or replaced.
10
No
10
10. WEAR PROPER APPAREL. Do not
wear loose clothing, gloves, neck-
ties, rings, bracelets, or other jewel-
ry which may get caught in moving
parts. Non-slip footwear is recom-
mended. Wear protective hair cover-
ing to contain long hair.
11. ALWAYS USE SAFETY GLASSES.
Also use face or dust mask if cutting
operation is dusty. Everyday eye-
glasses only have impact resistant
lenses, they are NOT safety glass-
es.
19. NEVER LEAVE TOOL RUNNING
UNATTENDED. TURN POWER
OFF. Don’t leave tool until it comes
to a complete stop.
12. SECURE WORK. Use clamps or a
vise to hold work when practical. It’s
safer than using your hand and frees
both hands to operate tool.
-2-
H0601 14.4V Cordless Jig Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
CHARGING SAFETY
1. READ ALL INSTRUCTIONS and
explosion.
warnings on the battery and charg-
er before charging the battery.
7. IF CHARGER LIGHT FAILS TO
COME ON check the incoming
power supply. If power source is
okay, then the fuse inside the
2. CHARGE ONLY USING THE SUP-
PLIED CHARGER AND BAT-
TERY. Do not use with other batter-
ies, chargers or cordless equip-
ment.
charger
needs
replacement.
Charger should be serviced by a
qualified electrical technician only.
3. DO NOT EXPOSE BATTERY OR
CHARGER TO WET OR RAINY
CONDITIONS. Moisture greatly
increases the risk of a shock haz-
ard.
8. DO NOT ATTEMPT TO MODIFY
THE CHARGER PLUG. Modifying
the plug will result in a safety haz-
ard and will void the warranty.
9. CHARGER IS DESIGNED TO
OPERATE AT 110-120 VOLTS.
Never try to plug into any circuit that
is not 110-120 volts. Never modify
or change the plug that is attached
to the charger unit to attempt to
plug into 220 volt. This can cause
serious electrical damage to the
unit, possible fire or explosion.
4. DO NOT TOUCH BATTERY
POLES with any conductive materi-
als. Touching any two poles at the
same time causes a short condition
and can cause sparks, electrical
shock or fire.
5. DO NOT STORE BATTERY WITH
CONDUCTIVE
MATERIALS.
Storing the battery in a box of
screws or nails can cause shorting
across the battery poles.
6. DO NOT THROW BATTERY IN
FIRE. Combustion of some of the
batteries’ component materials can
cause toxic fumes and possible
Never leave a battery unattend-
ed while charging. While charg-
ing will make the battery and
charging unit warm, if it
becomes hot to the touch, dis-
connect the charger immediate-
ly. There is a possibility of fire
hazard. Have the battery and
charging unit checked by a qual-
ified electrical service techni-
cian.
BATTERY MUST BE RECYCLED
OR DISPOSED OF PROPERLY.
Consult your local Yellow Pages direc-
tory under the category “Recycling” to
locate a battery recycler in your area.
-3-
H0601 14.4V Cordless Jig Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Most importantly, we stand behind our
Commentary
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
We are proud to offer the Grizzly Model
H0601 Cordless Jig Saw. The Model
H0601 is part of a growing Grizzly family
of fine power tools. When used according
to the guidelines set forth in this manual,
you can expect years of trouble-free,
enjoyable operation and proof of Grizzly’s
commitment to customer satisfaction.
Grizzly Industrial, Inc.
2406 Reach Road
Williamsport, PA 17701
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
The Model H0601 14.4V Cordless Jig Saw
contains a powerful motor that delivers a
speed of 2900 SPM. The saw has four set-
tings for blade orbit for cutting into differ-
ent materials, and a footplate that can be
angled for bevel cuts.
To operate this, or any power tool,
safely and efficiently, it is essential to
become as familiar with its characteris-
tics as possible. The time you invest
before you begin to use your Model
H0601 will be time well spent. DO NOT
operate this machine until you are
competely familiar with the contents of
this manual. Make sure you read and
understand all of the safety proce-
dures. If you do not understand some-
thing, DO NOT operate the machine.
We are pleased to provide this manual
with the Model H0601. It was written to
encourage safety considerations and
guide you through general operating pro-
cedures and maintenance. It represents
our effort to produce the best documenta-
tion possible.
The specifications, details, and pho-
tographs in this manual represent the
Model H0601 as supplied when the manu-
al was prepared. However, owing to
Grizzly’s policy of continuous improve-
ment, changes may be made at any time
with no obligation on the part of Grizzly. If
you have any comments regarding this
manual, please write to us at the address
below:
Operating this equipment has the
potential to propel debris into the air
which can cause eye injury. Always
wear safety glasses or goggles when
operating equipment. Be certain the
safety glasses you wear meet the
appropriate standards of the
Grizzly Industrial, Inc.
Technical Documentation
P.O. Box 2069
C
/O
American
National
Standards
Bellingham, WA 98227-2069
Institute (ANSI).
-4-
H0601 14.4V Cordless Jig Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU START
The battery in your new cordless power
Control Location
tool will not be fully charged when you
receive it. Follow the instructions below to
charge your battery.
Refer to Figure 1 for the location of the key
components and controls of the machine.
These controls are called out later in the
manual for their specific use when operat-
ing the saw. Become familiar with the con-
trols and all of the adjustments and set-
tings before operating the Jig Saw.
Battery charging with the standard
charger :
1. Plug the power cord for the charger
into the 110/120V outlet.
2. Insert the battery into the charger.
The battery fits into the oval recess in
only one way. Do not force the bat-
tery. Insert until it locks into place.
Specifications
Speed: 2900 SPM
3. The red LED light on the charging unit
will come on when the battery begins
its charging cycle.
Motor Type: Universal Brush Motor
Motor Power: 14.4V
Blade Orbit: 4 Settings
4. Charge battery for 3-5 hours for a full
charge from a fully depleted condi-
tion. The red LED will not go off until
the battery is removed from the
charger base.
Stroke Length: 1"
Blade: Universal Style Mounting, 3" - 5"
Blade Guide: Grooved Roller Bearing
Footplate: Adjustable from +45˚ to -45˚
Trigger Saftey Button
On/Off Trigger
Blade
Plunger
13⁄8" Dust Port
Orbit Selector
Blade Locking
Screw
Footplate
Fig 1. Location of controls.
-5-
H0601 14.4V Cordless Jig Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
BLADE SELECTION
Always select the correct saw blade for the
3. The number of teeth per inch
(T.P.I.) affects the smoothness
and speed of the cut. A wood cut-
ting blade for general purpose will
usually have 6-10 T.P.I., a metal
cutting will have 12-20 T.P.I.
Another factor is the tooth style
and how the teeth are set (the
amount the tooth is bent away
from the plane of the blade). Most
blade manufacturer’s provide
guidelines on their packaging for
the types of materials and speeds
to use for a particular blade style.
Review their guidelines carefully
before choosing a blade for a par-
ticular project.
material being cut. The resulting cut will be
cleaner and more accurate, and there will
be less stress on the machine. This Jig
Saw can be used to cut wood, metal or
plastics depending upon the type of blade
selected. The blades used must be of the
universal style mount. Grizzly offers a vari-
ety of blade styles in the current catalog.
A few points to remember in making your
blade selection:
1. The overall blade length will affect
the thickness of material which
can be cut. Most jig saw blades
range in length from 3" to 5".
2. The width of the blade (measured
from the tip of one of the teeth to
the back edge) affects how tight of
a curve can be cut. A 3⁄16" wide
blade will cut a tighter circle than a
3⁄8" wide one.
Figure 2 shows the range of blades for
wood and metal cutting available from
Grizzly.
Figure 2. Variety of wood and metal cutting blades.
H0601 14.4V Cordless Jig Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
-6-
OPERATIONS
Footplate Adjustment
The footplate can be adjusted for cutting at
90˚ to the surface as well as any angle
from 45˚. To be certain the footplate is
cutting at precisely 90˚, it is useful to check
the blade squareness to the footplate with
the use of a small machinist’s square (See
Figure 4).
Turn the switch off and remove the
battery from the Jig Saw before
attempting blade installation or any
adjustments. Serious injury may
occur if the unit should be acciden-
tally started while installing the blade.
Changing Blades
To adjust to another angle, use the sup-
plied Allen® Wrench to loosen the bolt
holding the footplate. Slide the plate for-
ward slightly to disengage it from the
notch, and tilt it to the desired angle. At the
45˚ points there are notches which posi-
tion the plate. By pushing the plate back
when near 45˚, the notches will lock the
plate in position. If an angle between 90˚
and 45˚ is desired, set the angle and leave
the plate in the forward position, and tight-
en the bolt.
Make sure the Orbit Selector switch is in
Position III. Take the blade and turn it so the
teeth are facing the side of the footplate,
and insert the mount end into the plunger.
See Figure 3. Twist the blade 90˚ so the
teeth are now pointing forward, then pull it
down slightly. Make certain the blade is
positioned in the groove of the roller which
backs up the blade.
Insert the Allen® wrench included with this
Jig Saw into the blade locking screw.
Tighten the screw while making sure the
blade stays in the roller groove. To remove
the blade, reverse the process described
above.
Fig 4. Checking blade squareness.
Fig 3. Inserting blade into plunger.
-7-
H0601 14.4V Cordless Jig Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
ORBITAL ACTION
straight up and down. This is good for
There are four settings for orbital action of
the blade, controlled by a lever switch. The
effect of the settings is shown in Figure 5
below. When set on Position III the blade
oscillates forward in the stroke, which is
helpful when cutting wood or soft materi-
als. The Position 0 setting eliminates all
forward oscillation and the blade strokes
materials with a strong cutting resistance
such as metals and where a very clean cut
edge is desired.
Changes in the orbital movement can be
made with the motor turned on.
Fig 5. Orbital movement settings and typical materials for each selection.
H0601 14.4V Cordless Jig Saw
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING TIPS AND MAINTENANCE
Operating Guides and Tips
Maintenance
Avoid overloading the jig saw. Do not
apply excessive pressure to the tool
while using. If the speed drops
abnormally, decrease pressure
immediately.
Your cordless power tool will give you hun-
dreds of hours of operation time before
ever needing service. The electrical com-
ponents of this cordless saw are not user
serviceable. Repair should always be
undertaken by a qualified electrical repair
technician.
Ensure the safety of the workplace.
Clear the work area of all parts and
debris that may cause injury by flying
objects. Securely fix the object to be
worked on in a vise or otherwise
clamp to avoid injury. Do not attempt
to hold workpiece by hand.
Keep the saw free from dirt and grease.
Always store it in a dry place, preferably in
the case that is supplied.
The battery will require periodic recharg-
ing, and eventually replacement after it has
exceeded its recharge life (approximately
800-1000 recharge cycles). You will notice
extended charging times or shortened
operation time as the battery experiences
more cycles. Battery must be recycled or
disposed or properly. Refer to the Grizzly
catalog for replacement batteries.
Inspect the tool before use. Run the tool
free of the workpiece before using to
ensure all parts are running smooth-
ly and there are no abnormal sounds
or sparks. If any defect is found,
have unit serviced.
Know your work site. Take care to make
sure the material being worked on is
not supporting another structure, or
that there are no obstructions.
Before cutting into walls, check for
wires, other electrical hazards, gas
lines or plumbing which may be hid-
den in the wall space.
Disassembly and improper reassembly
of this device can result in electrical
shock danger. Always have this device
serviced by a qualified electrical repair
technician. Serious injury will result.
-9-
H0601 14.4V Cordless Jig Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main-
tenance. This is Grizzly’s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are here-
by limited to the duration of this written warranty. We do not warrant or represent that the
merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, con-
tingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Number’’, which must be clearly posted on the outside as
well as the inside of the carton. We will not accept any item back without this number. Proof
of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they con-
stantly strive to achieve better quality equipment. We make every effort to ensure that our
products meet high quality and durability standards and we hope you never need to use this
warranty.
Please feel free to write or call us if you have any questions about the machine or the man-
ual.
Grizzly Industrial, Inc.
2406 Reach Road
Williamsport, PA 17701
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
Thank you again for your business and continued support. We hope to serve you again
soon.
-10-
H0601 14.4V Cordless Jig Saw
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name__________________________________________________________
Street__________________________________________________________
City____________________State________Zip_________
Phone Number____________E-Mail___________________FAX____________
MODEL # H0601 14.4V Cordless Jig Saw
Order#______________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help
us develop better products and services. Of course, all information is strictly confidential.
9. How many of the machines checked above are
Grizzly? ____________
1. How did you learn about us?
___Advertisement
___Friend
___Catalog
___World Wide Web
___Other__________________________
___Card Deck
10. Which portable/hand held power tools do you own?
Check all that apply.
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
2. What is your annual household income?
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
___Miter Saw
___Other_________________________________
3. What is your age group?
___20-29
11. What machines/supplies would you like Grizzly
Industrial to carry?
___50-59
___60-69
___70 +
___30-39
___40-49
___12" Table Saw
___12" Jointer
___Radial Arm Saw
___Panel Saw
___Lumber
___Brass Hardware
4. How long have you been a woodworker?
___Paint & Finishing Supplies
___Contractor’s Supplies
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
___Combination Planer/Jointer
___Other_________________________________
5. How would you rank your woodworking skills?
___Simple
___Advanced
___Intermediate
___Master Craftsman
12. What new accessories would you like Grizzly
Industrial to carry?
6. What stationary woodworking tools do you own?
Check all that apply.
___Builders Hardware
___Fasteners
___Hand Tools
___Air Compressor
___Band Saw
___Panel Saw
___Planer
___Wood Components
___Other_________________________________
___Drill Press
___Power Feeder
___Radial Arm Saw
___Shaper
___Jointer
___Lathe
___Drum Sander
___Dust Collector
___Spindle Sander
___Table Saw
13. What other companies do you purchase your tools
and supplies from?
_________________________________________
_________________________________________
_________________________________________
___Mortiser
___Wide Belt Sander
___Horiz.Boring Machine
___Vacuum Veneer Press
14. Do you think your purchase represents good value?
___Other______________________________
___Yes
___No
7. How many of your woodworking machines are
Grizzly? _____________
15. Would you recommend Grizzly to a friend?
___Yes ___No
8. Which benchtop tools do you own? Check all
that apply.
16. Would you allow us to use your name as a refer-
ence for Grizzly customers in your area? Note: We
never use names more than three times.
___1"x42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
___Yes
___No
___8" Table Saw
___Scroll Saw
___Spindle/Belt Sander ___Mini Jointer
___10"-12"Thickness Planer
___8" - 10" Bandsaw
___Disc/Belt Sander
17.Comments:________________________________
_________________________________________
_________________________________________
_________________________________________
___Other______________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
Send a Grizzly Catalog to a friend:
Name________________________________
Street________________________________
City______________State______Zip_______
FOLD ALONG DOTTED LINE
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
|