MODEL G0664
HEAVY DUTY METAL CUTTING
BANDSAW w/ROLLERS
OWNER'S MANUAL
Copyright © May, 2008 By grizzly industrial, inC.
WARNING: NO pORTION Of THIS MANUAL MAY BE REpRODUCED IN ANY SHApE
OR fORM WITHOUT THE WRITTEN AppROVAL Of GRIzzLY INDUSTRIAL, INC.
#JB10466 printed in taiWan
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
INTRODUCTION............................................... 4
SECTION 5: ACCESSORIES......................... 39
Foreword........................................................ 4
Contact info.................................................... 4
Functional overview ...................................... 4
identification................................................... 5
Machine data sheet ...................................... 6
SECTION 6: MAINTENANCE......................... 41
schedule...................................................... 41
Cleaning....................................................... 41
lubrication ................................................... 41
hydraulic system......................................... 42
SECTION 1: SAfETY....................................... 8
safety instructions for Machinery .................. 8
additional safety
SECTION 7: SERVICE ................................... 43
troubleshooting ........................................... 43
Blade Change .............................................. 46
Blade guides ............................................... 47
Wheel Brush ................................................ 48
squaring Blade ............................................ 49
swivel stops ................................................ 50
Feed stop .................................................... 51
limit switches.............................................. 51
instructions for Bandsaws............................ 10
SECTION 2: CIRCUIT REQUIREMENTS ...... 11
220V operation............................................ 11
SECTION 3: SETUp ....................................... 12
setup safety ................................................ 12
items needed for setup............................... 12
unpacking.................................................... 12
inventory ...................................................... 13
hardware recognition Chart ....................... 14
Clean up...................................................... 15
site Considerations...................................... 15
Moving & placing......................................... 16
Mounting to shop Floor ............................... 17
leveling Feet ............................................... 18
leveling Machine......................................... 18
roller table assembly................................. 19
required adjustments.................................. 20
test run ...................................................... 21
recommended adjustments........................ 22
SECTION 8: WIRING...................................... 52
electrical safety instructions........................ 52
Wiring overview........................................... 53
Control Box Wiring diagram........................ 54
Components Wiring diagram....................... 55
SECTION 9: Hydraulics................................. 57
hydraulic system diagram .......................... 57
hydraulic Components................................. 58
SECTION 10: pARTS..................................... 59
Main parts Breakdown................................. 59
Main parts list............................................. 60
Main parts list (Continued)......................... 61
roller stand parts Breakdown & list .......... 61
Base Breakdown.......................................... 63
labels Breakdown and list.......................... 64
SECTION 4: OpERATIONS ........................... 23
operation safety.......................................... 23
Basic Controls.............................................. 24
Control panel ............................................... 25
Cutting angle ............................................... 26
Coolant Catch tray...................................... 27
Blade guide position ................................... 27
Workstop...................................................... 28
Vise.............................................................. 28
Cutting Fluid system.................................... 30
Cutting Fluid tips ........................................ 31
Blade selection............................................ 32
setting Feed rate........................................ 33
Blade speed ................................................ 34
Chip inspection Chart .................................. 35
Blade tensioning ......................................... 36
Blade Care & Break-in................................. 36
Blade Breakage ........................................... 37
Workpiece inspection................................... 37
operation tips ............................................. 38
WARRANTY AND RETURNS ........................ 67
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
functional Overview
foreword
We are proud to offer the Model g0664 heavy
duty Metal Cutting Bandsaw w/rollers. this
machine is part of a growing grizzly family of fine
metalworking machinery. When used according
to the guidelines set forth in this manual, you can
expect years of trouble-free, enjoyable operation
and proof of grizzly’s commitment to customer
satisfaction.
a horizontal metal cutting bandsaw is used to
make straight cuts in metal workpieces.
the Model g0664 heavy duty Metal Cutting
Bandsaw with rollers features a 21⁄2 hp motor,
hydraulic upfeed and downfeed, a vise with
hydraulic clamping, two blade speeds, variable
speed downfeed, cutting angles from -45˚ to 60˚,
a blade coolant system, infeed and outfeed roller
tables, and laser light cut alignment.
the specifications, drawings, and photographs
illustrated in this manual represent the Model
g0664 when the manual was prepared. however,
owing to grizzly’s policy of continuous improve-
ment, changes may be made at any time with no
obligation on the part of grizzly. For your conve-
nience, we always keep current grizzly manuals
any updates to your machine will be reflected
in these manuals as soon as they are complete.
Visit our site often to check for the latest updates
to this manual!
to make cuts, the operator first adjusts the blade
to the desired cutting angle, then raises the blade
and opens the vise. a workpiece is placed onto
the table and the vise is manually closed to within
1
⁄4" of the workpiece. the vise close button is
pressed to hydraulically clamp the workpiece into
the vise. if needed for the operation, the blade
coolant pump is started and the blade is turned
on. the blade is hydraulically lowered into the
workpiece by pressing the blade down button.
the feed speed is adjusted with the feed speed
knob on the control panel.
Contact Info
When the cut is complete, the blade automati-
cally stops and returns to the top of its travel. the
workpiece is released from the vise by pressing
the vise open button.
We stand behind our machines. if you have any
service questions, parts requests or general ques-
tions about the machine, please call or write us at
the location listed below.
long workpieces can be supported by the infeed
and outfeed roller tables.
grizzly industrial, inc.
1203 lycoming Mall Circle
Muncy, pa 17756
phone: (570) 546-9663
Fax: (800) 438-5901
e-Mail: techsupport@grizzly.com
if you have any comments regarding this manual,
please write to us at the address below:
grizzly industrial, inc.
technical documentation Manager
p.o. Box 2069
C
/
o
Bellingham, Wa 98227-2069
email: manuals@grizzly.com
-4-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification
e
d
C
F
g
B
i
a
h
M
J
K
l
figure 2. g0664 Machine identification.
A. Blade tension handwheel
B. Cutting Fluid Flow Valve
C. Cut alignment laser
D. Bandsaw Motor
E. Control panel
f. Machine on/oFF switch
G. Feed pressure adjust spring
H. saw Control ram
I. infeed/outfeed tables
J. Main support Cabinet
K. headstock swivel lock lever
L. Cabinet
M. Vise handwheel
-5-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Machine Data Sheet
MACHINE DATA
SHEET
8jhidbZgꢀHZgk^XZꢀꢁ/ꢀꢂ*,%ꢃꢀ*)+".++(ꢀ™ꢀIdꢀDgYZgꢀ8Vaa/ꢀꢂ-%%ꢃꢀ*'("),,,ꢀ™ꢀ;Vmꢀꢁ/ꢀꢂ-%%ꢃꢀ)(-"*.%&
MODEL G0664
HEAVY DUTY METAL CUTTING BANDSAW
Product Dimensions:
CZiꢀLZ^\]iꢀꢀ####################################################################################################################### &%&'ꢀaWh#ꢀ ꢀꢂGdaaZgꢀIVWaZh/ꢀ&,+ꢀaWh#ꢃ
AZc\i]$L^Yi]$=Z^\]iꢀꢀ####################################################################################################### &%+ꢄꢀmꢀ,)ꢄꢀmꢀ+'&$'ꢄꢀꢂl$ꢀGdaaZgꢀIVWaZhꢃ
;ddiꢀEg^ciꢀꢂAZc\i]$L^Yi]ꢃꢀ##################################################################################################### &%%ꢄꢀmꢀ*(&$'ꢄꢀꢂHiVcYꢀ'-ꢅꢄꢀmꢀ*(ꢅꢄꢃ
Shipping Dimensions:
IneZꢀ############################################################################################################################### LddYꢀHaViꢀ8gViZꢀꢂ&ꢀd[ꢀ'ꢃ!ꢀ7dmꢀꢂ'ꢀd[ꢀ'ꢃꢀ
8dciZciꢀ######################################################################################################################### BVX]^cZꢀꢂ&ꢀd[ꢀ'ꢃ!ꢀGdaaZgꢀIVWaZhꢀꢂ'ꢀd[ꢀ'ꢃ
LZ^\]iꢀ#########################################################################################################################################################&%,-ꢀaWh#ꢀ ꢀ&-*ꢀaWh#ꢀ
AZc\i]$L^Yi]$=Z^\]iꢀ######################################################################################-+ꢄꢀmꢀ('ꢅꢄꢀmꢀ)*ꢄꢀꢂ&ꢀd[ꢀ'ꢃ!ꢀ-'ꢄꢀmꢀ(-ꢄꢀmꢀ&*ꢄꢀꢂ'ꢀd[ꢀ'ꢃ
Electrical:
Hl^iX]ꢀ##############################################################################################################################################8dcigdaꢀ7dmꢀdcꢀHl^c\ꢀ7VhZꢀ
Hl^iX]ꢀKdaiV\Zꢀ################################################################################################################################################################### ''%K
8dgYꢀAZc\i]ꢀ##########################################################################################################################################################################+ꢀ[i#
8dgYꢀ<Vj\Zꢀ#################################################################################################################################################################&)ꢀ\Vj\Z
GZXdbbZcYZYꢀ8^gXj^iꢀH^oZꢀ############################################################################################################################################&'ꢀVbe
>cXajYZYꢀEaj\ꢀ######################################################################################################################################################################### Cd
GZXdbbZcYZYꢀEaj\ꢀ##########################################################################################################################################################&*"&*
Motors:
Main
IneZꢀ##########################################################################################################################################################I:;8ꢀ>cYjXi^dc
=dghZedlZgꢀ############################################################################################################################################################'#*ꢀ=E
KdaiV\Zꢀ##################################################################################################################################################################### ''%K
EgZl^gZYꢀ################################################################################################################################################################### ''%K
E]VhZꢀ###################################################################################################################################################################### I]gZZ
6behꢀ################################################################################################################################################################# ,#+)$+#+6
HeZZYꢀ######################################################################################################################################################()*%$&,'*ꢀGEB
8nXaZꢀ######################################################################################################################################################################## +%ꢀ=o
CjbWZgꢀD[ꢀHeZZYhꢀ##########################################################################################################################################################'
EdlZgꢀIgVch[Zgꢀ#########################################################################################################################################<ZVgꢀ7dmꢀ9g^kZ
7ZVg^c\hꢀ#####################################################################################################################################H]^ZaYZYꢀVcYꢀAjWg^XViZY
Hydraulic Motor
IneZꢀ##########################################################################################################################################################I:;8ꢀ>cYjXi^dc
=dghZedlZgꢀ##############################################################################################################################################################ꢅꢀ=E
KdaiV\Zꢀ##################################################################################################################################################################### ''%K
EgZl^gZYꢀ################################################################################################################################################################### ''%K
E]VhZꢀ###################################################################################################################################################################### I]gZZ
6behꢀ############################################################################################################################################################################ '6
HeZZYꢀ###############################################################################################################################################################&,'*ꢀGEB
8nXaZꢀ######################################################################################################################################################################## +%ꢀ=o
-6-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Coolant Pump Motor
IneZꢀ##########################################################################################################################################################I:;8ꢀ>cYjXi^dc
EdlZgꢀ######################################################################################################################################################################## *(L
KdaiV\Zꢀ##################################################################################################################################################################### ''%K
6behꢀ######################################################################################################################################################################### %#(6
HeZZYꢀ###############################################################################################################################################################()*%ꢀGEB
8nXaZꢀ######################################################################################################################################################################## +%ꢀ=o
Main Specifications:
Operation Information
7aVYZꢀHeZZYꢀ###############################################################################################################################################&+%!ꢀ('%ꢀ;EB
HiVcYVgYꢀ7aVYZꢀH^oZꢀ##################################################################################################################################&&¿&+ꢁꢀmꢀ&(%&&¿&+ꢁ
B^iZgꢀ6c\aZꢀ########################################################################################################################################## G^\]iꢀ)*•!ꢀAZ[iꢀ+%•
Cutting Capacities
6c\aZꢀ8jihꢀ########################################################################################################################################### G^\]iꢀ)*•!ꢀAZ[iꢀ+%•
K^hZꢀ?Vlꢀ9Zei]ꢀ######################################################################################################################################################## &%ꢂꢁ
K^hZꢀ?Vlꢀ=Z^\]iꢀ########################################################################################################################################################## +ꢃꢁ
.%•ꢀGdjcYꢀBVm#ꢀ8VeVX^inꢀ#########################################################################################################################################&&,¿-
ꢁ
.%•ꢀHfjVgZꢀBVm#ꢀ8VeVX^inꢀ################################################################################################################################# &%ꢁꢀmꢀ&%ꢁ
.%•ꢀGZXiVc\jaVgꢀBVm#ꢀ8VeVX^inꢀ############################################################################################################################ &(ꢁꢀmꢀ-ꢁ
)*•ꢀGdjcYꢀBVm#ꢀ8VeVX^inꢀ########################################################################################################################################### &%ꢁ
)*•ꢀHfjVgZꢀBVm#ꢀ8VeVX^inꢀ#################################################################################################################################### .ꢁꢀmꢀꢀ.ꢁ
)*•ꢀGZXiVc\jaVgꢀBVm#ꢀ8VeVX^inꢀ######################################################################################################################### ,ꢄꢁꢀmꢀ&%ꢁ
(%•ꢀGdjcYꢀBVm#ꢀ8VeVX^inꢀ############################################################################################################################################# ,ꢁ
(%•ꢀHfjVgZꢀBVm#ꢀ8VeVX^inꢀ############################################################################################################################### +ꢄꢁꢀmꢀ+ꢄꢁꢀ
(%•ꢀGZXiVc\jaVgꢀBVm#ꢀ8VeVX^inꢀ######################################################################################################################## +ꢄꢁꢀmꢀ+ꢄꢁꢀ
ꢀ
Construction
IVWaZꢀ8dchigjXi^dcꢀ#############################################################################################################################################8Vhiꢀ>gdc
L]ZZaꢀ8dchigjXi^dcꢀJeeZgꢀ#################################################################################################################################8Vhiꢀ>gdc
L]ZZaꢀ8dchigjXi^dcꢀAdlZgꢀ#################################################################################################################################8Vhiꢀ>gdc
7dYnꢀ8dchigjXi^dcꢀ##############################################################################################################################################8Vhiꢀ>gdc
7VhZꢀ8dchigjXi^dcꢀ##############################################################################################################################################8Vhiꢀ>gdc
HiVcYꢀ8dchigjXi^dcꢀ######################################################################################################################################;dgbZYꢀHiZZa
L]ZZaꢀ8dkZgꢀ8dchigjXi^dcꢀ################################################################################################################### EgZ";dgbZYꢀHiZZa
EV^ciꢀ########################################################################################################################################################EdlYZgꢀ8dVi^c\
Other
7aVYZꢀ<j^YZhꢀJeeZgꢀVcYꢀAdlZgꢀ#################################################################################### Ijc\hiZcꢀ8VgW^YZꢀI^eeZYꢀ<j^YZꢀ
8ddaVciꢀ8VeVX^inꢀ##################################################################################################################################################'ꢄꢀ<Va#
Other Specifications:
8djcignꢀD[ꢀDg^\^cꢀ############################################################################################################################################################ IV^lVc
LVggVcinꢀ###########################################################################################################################################################################&ꢀNZVg
HZg^VaꢀCjbWZgꢀAdXVi^dcꢀ#################################################################################################################################### <g^ooanꢀ>9ꢀAVWZa
6hhZbWanꢀI^bZꢀ#########################################################################################################################################################(%ꢀb^cjiZh
Features:
IldꢀHeZZYh
6Y_jhiVWaZꢀ=nYgVja^Xꢀ9dlc[ZZYꢀVcYꢀFj^X`ꢀA^[iꢀHnhiZb
6jidbVi^XꢀH]ji"d[[
7aVYZꢀIZch^dcꢀ>cY^XVidg
6Y_jhi^c\ꢀHeg^c\ꢀ;dgꢀHbddi]ꢀ9dlc[ZZY
8dcigdaꢀEVcZa
(.ꢁAꢀmꢀ&-ꢁLꢀ;gdciꢀꢅꢀGZVgꢀGdaaZgꢀIVWaZh
AVhZgꢀ<j^YZ
-7-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
3%#4)/. ꢄꢈ 3!&%49
&OR 9OUR /WN 3AFETYꢇ 2EAD )NSTRUCTION
-ANUAL "EFORE /PERATING THIS -ACHINE
4HE PURPOSE OF SAFETY SYMBOLS IS TO ATTRACT YOUR ATTENTION TO POSSIBLE HAZARDOUS CONDITIONSꢁ 4HIS
MANUAL USES A SERIES OF SYMBOLS AND SIGNAL WORDS INTENDED TO CONVEY THE LEVEL OF IMPORTANCE
OF THE SAFETY MESSAGESꢁ 4HE PROGRESSION OF SYMBOLS IS DESCRIBED BELOWꢁ 2EMEMBER THAT SAFETY
MESSAGES BY THEMSELVES DO NOT ELIMINATE DANGER AND ARE NOT A SUBSTITUTE FOR PROPER ACCIDENT
PREVENTION MEASURESꢁ
)NDICATES AN IMMINENTLY HAZARDOUS SITUATION WHICHꢇ IF NOT AVOIDEDꢇ
7),, RESULT IN DEATH OR SERIOUS INJURYꢁ
)NDICATES A POTENTIALLY HAZARDOUS SITUATION WHICHꢇ IF NOT AVOIDEDꢇ
#/5,$ RESULT IN DEATH OR SERIOUS INJURYꢁ
)NDICATES A POTENTIALLY HAZARDOUS SITUATION WHICHꢇ IF NOT AVOIDEDꢇ
-!9 RESULT IN MINOR OR MODERATE INJURYꢁ )T MAY ALSO BE USED TO ALERT
AGAINST UNSAFE PRACTICESꢁ
4HIS SYMBOL IS USED TO ALERT THE USER TO USEFUL INFORMATION ABOUT
PROPER OPERATION OF THE MACHINEꢁ
./4)#%
Safety Instructions for Machinery
3AFETY )NSTRUCTIONS FOR -ACHINERY
ꢄꢁ 2%!$ 4(% %.4)2% -!.5!, "%&/2%
34!24).' -!#().%29ꢁ BVX]^cZgnꢀegZh"
Zcihꢀ hZg^djhꢀ ^c_jgnꢀ ]VoVgYhꢀ idꢀ jcigV^cZYꢀ
jhZgh#ꢀ
ꢀꢁ !,7!93 53% (%!2).' 02/4%#4)/.
7(%. /0%2!4).' -!#().%29ꢁꢀ
BVX]^cZgnꢀ cd^hZꢀ XVcꢀ XVjhZꢀ eZgbVcZciꢀ
]ZVg^c\ꢀadhh#ꢀ
ꢂꢁ 7%!2 02/0%2 !00!2%,ꢁꢀ 9Dꢀ CDIꢀ
lZVgꢀaddhZꢀXadi]^c\!ꢀ\adkZh!ꢀcZX`i^Zh!ꢀg^c\h!ꢀ
dgꢀ_ZlZagnꢀi]ViꢀXVcꢀXViX]ꢀ^cꢀbdk^c\ꢀeVgih#ꢀ
LZVgꢀ egdiZXi^kZꢀ ]V^gꢀ XdkZg^c\ꢀ idꢀ XdciV^cꢀ
adc\ꢀ]V^gꢀVcYꢀlZVgꢀcdc"ha^eꢀ[ddilZVg#
ꢅꢁ !,7!93 53% !.3) !002/6%$
3!&%49 ',!33%3 7(%. /0%2!4).'
-!#().%29ꢁ :kZgnYVnꢀ ZnZ\aVhhZhꢀ dcanꢀ
]VkZꢀ ^beVXiꢀ gZh^hiVciꢀ aZchZh·i]Znꢀ VgZꢀ
CDIꢀhV[Zinꢀ\aVhhZh#
ꢃꢁ .%6%2 /0%2!4% -!#().%29 7(%.
4)2%$ /2 5.$%2 4(% ).&,5%.#% /&
$25'3 /2 !,#/(/,ꢁ 7ZꢀbZciVaanꢀVaZgiꢀ
ViꢀVaaꢀi^bZhꢀl]Zcꢀgjcc^c\ꢀbVX]^cZgn#
ꢆꢁ !,7!93 7%!2 ! .)/3( !002/6%$
2%30)2!4/2 7(%. /0%2!4).'
-!#().%29 4(!4 02/$5#%3 $534ꢁꢀ
BdhiꢀineZhꢀd[ꢀYjhiꢀꢁlddY!ꢀbZiVa!ꢀZiX#ꢂꢀXVcꢀ
XVjhZꢀhZkZgZꢀgZhe^gVidgnꢀ^aacZhhZh#
-8-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
3AFETY )NSTRUCTIONS FOR -ACHINERY
ꢀꢁ /.,9 !,,/7 42!).%$ !.$ 02/0ꢂ
ꢅꢀꢁ 2%-/6% !$*534).' +%93 !.$
%2,9 350%26)3%$ 0%23/..%, 4/
/0%2!4% -!#().%29ꢁꢀ BV`Zꢀ hjgZꢀ
deZgVi^dcꢀ^chigjXi^dchꢀVgZꢀhV[ZꢀVcYꢀXaZVganꢀ
jcYZghiddY#
72%.#(%3ꢁꢀBV`ZꢀVꢀ]VW^iꢀd[ꢀX]ZX`^c\ꢀ[dgꢀ
`ZnhꢀVcYꢀVY_jhi^c\ꢀlgZcX]ZhꢀWZ[dgZꢀijgc"
^c\ꢀbVX]^cZgnꢀ/.#
ꢅꢃꢁ #(%#+ &/2 $!-!'%$ 0!243
"%&/2% 53).' -!#().%29ꢁꢀ8]ZX`ꢀ[dgꢀ
W^cY^c\ꢀdgꢀb^hVa^\cZYꢀeVgih!ꢀWgd`ZcꢀeVgih!ꢀ
addhZꢀWdaih!ꢀVcYꢀVcnꢀdi]ZgꢀXdcY^i^dchꢀi]Viꢀ
bVnꢀ^beV^gꢀbVX]^cZꢀdeZgVi^dc#ꢀGZeV^gꢀdgꢀ
gZeaVXZꢀYVbV\ZYꢀeVgihꢀWZ[dgZꢀdeZgVi^dc#
ꢃꢁ +%%0 #(),$2%. !.$ 6)3)4/23 !7!9ꢁ
@ZZeꢀ Vaaꢀ X]^aYgZcꢀ VcYꢀ k^h^idghꢀ Vꢀ hV[Zꢀ Y^h"
iVcXZꢀ[gdbꢀi]Zꢀldg`ꢀVgZV#
ꢄꢁ -!+% 7/2+3(/0 #(),$02//&ꢁꢀJhZꢀ
eVYadX`h!ꢀ bVhiZgꢀ hl^iX]Zh!ꢀ VcYꢀ gZbdkZꢀ
hiVgiꢀhl^iX]ꢀ`Znh#
ꢅꢄꢁ 53% 2%#/--%.$%$ !##%33/2)%3ꢁꢀ
GZ[Zgꢀidꢀi]Zꢀ^chigjXi^dcꢀbVcjVaꢀ[dgꢀgZXdb"
bZcYZYꢀ VXXZhhdg^Zh#ꢀ >begdeZgꢀ VXXZhhd"
g^Zhꢀ^cXgZVhZꢀg^h`ꢀd[ꢀ^c_jgn#
ꢅꢆꢁ .%6%2 ,%!6% 7(%. -!#().% )3
25..).'ꢁ IjgcꢀedlZgꢀ/&&ꢀVcYꢀVaadlꢀVaaꢀ
bdk^c\ꢀeVgihꢀidꢀXdbZꢀidꢀVꢀXdbeaZiZꢀhideꢀ
WZ[dgZꢀaZVk^c\ꢀbVX]^cZꢀjcViiZcYZY#
ꢇꢆꢁ $/ ./4 &/2#% -!#().%29ꢁꢀ Ldg`ꢀ Viꢀ
i]ZꢀheZZYꢀ[dgꢀl]^X]ꢀi]ZꢀbVX]^cZꢀdgꢀVXXZh"
hdgnꢀlVhꢀYZh^\cZY#
ꢅꢅꢁ $/ ./4 53% ). $!.'%2/53
%.6)2/.-%.43ꢁ 9Dꢀ CDIꢀ jhZꢀ bVX]^c"
Zgnꢀ^cꢀYVbe!ꢀlZiꢀadXVi^dch!ꢀdgꢀl]ZgZꢀVcnꢀ
[aVbbVWaZꢀdgꢀcdm^djhꢀ[jbZhꢀbVnꢀZm^hi#ꢀ
ꢇꢅꢁ 3%#52% 7/2+0)%#%ꢁꢀ JhZꢀ XaVbehꢀ dgꢀ
Vꢀk^hZꢀidꢀ]daYꢀi]Zꢀldg`e^ZXZꢀl]ZcꢀegVXi^"
XVa#ꢀ 6ꢀ hZXjgZYꢀ ldg`e^ZXZꢀ egdiZXihꢀ ndjgꢀ
]VcYhꢀVcYꢀ[gZZhꢀWdi]ꢀ]VcYhꢀidꢀdeZgViZꢀi]Zꢀ
bVX]^cZ#
ꢅꢇꢁ +%%0 7/2+ !2%! #,%!. !.$ 7%,,
,)'(4%$ꢁ 8ajiiZgꢀVcYꢀYVg`ꢀh]VYdlhꢀbVnꢀ
XVjhZꢀVXX^YZcih#
ꢇꢇꢁ $/ ./4 /6%22%!#(ꢁꢀBV^ciV^cꢀhiVW^a^inꢀ
VcYꢀWVaVcXZꢀViꢀVaaꢀi^bZh#
ꢅꢈꢁ 53% ! '2/5.$%$ %84%.3)/. #/2$
2!4%$&/24(%-!#().%!-0%2!'%ꢁ
<gdjcYZYꢀXdgYhꢀb^c^b^oZꢀh]dX`ꢀ]VoVgYh#
JcYZgh^oZYꢀ XdgYhꢀ XgZViZꢀ ZmXZhh^kZꢀ ]ZVi#ꢀ
6alVnhꢀgZeaVXZꢀYVbV\ZYꢀZmiZch^dcꢀXdgYh#
ꢇꢈꢁ -!.9
-!#().%3
#!.
%*%#4
7/2+0)%#%3 4/7!2$ /0%2!4/2ꢁ
@cdlꢀVcYꢀVkd^YꢀXdcY^i^dchꢀi]ViꢀXVjhZꢀi]Zꢀ
ldg`e^ZXZꢀidꢀꢁ`^X`WVX`#ꢁ
ꢅꢉꢁ !,7!93 $)3#/..%#4 &2/- 0/7%2
ꢇꢉꢁ !,7!93 ,/#+ -/"),% "!3%3
3/52#%
"%&/2%
3%26)#).'
ꢌ)& 53%$
"%&/2% /0%2!4).'
-!#().%29#ꢀBV`ZꢀhjgZꢀhl^iX]ꢀ^hꢀ^cꢀD;;
ꢀ
-!#().%29#
edh^i^dcꢀWZ[dgZꢀgZXdccZXi^c\#
ꢇꢊꢁ #%24!). $534 -!9 "% (!:!2$/53ꢀ
idꢀ i]Zꢀ gZhe^gVidgnꢀ hnhiZbhꢀ d[ꢀ eZdeaZꢀ VcYꢀ
Vc^bVah!ꢀZheZX^Vaanꢀ[^cZꢀYjhi#ꢀ7ZꢀVlVgZꢀd[ꢀ
i]Zꢀ ineZꢀ d[ꢀ Yjhiꢀ ndjꢀ VgZꢀ ZmedhZYꢀ idꢀ VcYꢀ
ValVnhꢀlZVgꢀVꢀgZhe^gVidgꢀYZh^\cZYꢀidꢀ[^aiZgꢀ
i]ViꢀineZꢀd[ꢀYjhi#
ꢅꢊꢁ -!).4!). -!#().%29 7)4( #!2%ꢁꢀ
@ZZeꢀWaVYZhꢀh]VgeꢀVcYꢀXaZVcꢀ[dgꢀWZhiꢀVcYꢀ
hV[ZhiꢀeZg[dgbVcXZ#ꢀ;daadlꢀ^chigjXi^dchꢀ[dgꢀ
ajWg^XVi^c\ꢀVcYꢀX]Vc\^c\ꢀVXXZhhdg^Zh#
ꢅꢋꢁ -!+% 352% '5!2$3 !2% ). 0,!#%
!.$ 7/2+ #/22%#4,9 "%&/2%
53).' -!#().%29ꢁ
-9-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety Instructions for Bandsaws
8. fIRE HAzARD. use eXtreMe Caution
if cutting magnesium. using the wrong cut-
ting fluid will lead to chip fire and possible
explosion.
1. BLADE CONDITION. do not operate with
dull, cracked or badly worn blade. inspect
blades for cracks and missing teeth before
each use.
9. CUTTING fLUID SAfETY. always follow
manufacturer’s cutting fluid safety instruc-
tions. pay particular attention to contact,
contamination, inhalation, storage and dis-
posal warnings. spilled cutting fluid cre-
ates a slipping and toxicity hazard.
2. HAND pLACEMENT. never position fin-
gers or thumbs in line with the cut. hands
could be crushed in vise or by falling
machine components, or cut by the blade.
3. ENTANGLEMENT HAzARDS. do not
operate this bandsaw without blade guard
in place. otherwise, loose clothing, jewelry,
long hair and work gloves can be drawn
into working parts.
10. ATTENTION TO WORK AREA. never
leave a machine running and unattended.
pay attention to the actions of others in the
area to avoid unintended accidents.
4. BLADE REpLACEMENT. When replacing
blades, make sure teeth face toward the
workpiece. Wear gloves to protect hands
and safety glasses to protect eyes.
11. MAINTENANCE/SERVICE. all inspec-
tions, adjustments, and maintenance are
to be done with the machine OFF and the
power disconnected to the machine. Wait
for all moving parts to come to a complete
stop.
5. WORKpIECE HANDLING. always sup-
port the workpiece with table, vise, or other
support fixture. Flag long pieces to avoid a
tripping hazard. never hold the workpiece
with your hands during a cut.
12. HEARING pROTECTION & HAzARDS.
noise generated by blade and workpiece
vibration, material handling, and power
transmission can cause permanent hear-
ing loss over time and interfere with com-
munication and audible signals. always
wear hearing protection.
6. LOSS Of STABILITY. unsupported
workpieces may jeopardize machine sta-
bility and cause the machine to tip and fall,
which could cause serious injury.
13. HOT SURfACES. due to friction, the
workpiece, chips, and some machine com-
ponents can be hot enough to burn you.
7. pOWERINTERRUpTION. unplug machine
after power interruption. Machines without
magnetic switches can start up after power
is restored.
No list of safety guidelines can be complete.
Every shop environment is different. Always
consider safety first, as it applies to your
individual working conditions. Use this and
other machinery with caution and respect.
failure to do so could result in serious per-
sonal injury, damage to equipment, or poor
work results.
Like all machinery there is potential danger
when operating this machine. Accidents are
frequently caused by lack of familiarity or
failure to pay attention. Use this machine
with respect and caution to decrease the
risk of operator injury. If normal safety pre-
cautions are overlooked or ignored, serious
personal injury may occur.
-10-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: CIRCUIT REQUIREMENTS
power Connection Device
220V Operation
the type of plug required to connect your machine
to power depends on the type of service you cur-
rently have or plan to install. We recommend
using the plug shown in figure 3.
Serious personal injury could occur if you
connect the machine to power before com-
pleting the setup process. DO NOT connect
<gdjcYZY
DjiaZiꢀ7dm
the machine to the power until instructed
later in this manual.
8jggZci
8Vggn^c\
7aVYZh
Electrocution or fire could
result if machine is not
<gdjcY^c\ꢀE^c
grounded and installed in
compliance with electrical
codes. Compliance MUST
be verified by a qualified
electrician!
figure 3. neMa 15-15 plug and outlet.
Extension Cords
using extension cords may reduce the life of the
motor. instead, place the machine near a power
source. if you must use an extension cord:
full Load Amperage Draw
this machine draws the following amps under
maximum load:
•
•
•
use at least a 14 gauge cord that does not
exceed 50 feet in length!
amp draw.............................................. 10 amps
the extension cord must also have a ground
wire and plug pin.
power Supply Circuit Requirements
a qualified electrician Must size cords over
50 feet long to prevent motor damage.
you Must connect your machine to a grounded
circuit that is rated for the amperage given below.
never replace a circuit breaker on an existing cir-
cuit with one of higher amperage without consult-
ing a qualified electrician to ensure compliance
with wiring codes. If you are unsure about the
wiring codes in your area or you plan to con-
nect your machine to a shared circuit, consult
a qualified electrician.
Minimum Circuit size............................. 15 amps
-11-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: SETUp
Setup Safety
Items Needed for
Setup
the following items are needed to complete the
setup process, but are not included with your
machine:
This machine presents
serious injury hazards
to untrained users. Read
through this entire manu-
al to become familiar with
the controls and opera-
tions before starting the
machine!
Description
Qty
•
•
•
•
assistant..................................................... 1
safety glasses (for each person)........1 pair
Mounting hardware (optional) .... as needed
power lifting equipment
(rated for at least 1200 lbs.) ...................... 1
lifting straps and hooks
•
(rated for at least 1200 lbs.) ...... as needed
Wear safety glasses dur-
ing the entire setup pro-
cess!
Unpacking
the Model g0664 was carefully packed when it
left our warehouse. if you discover the machine
is damaged after you have signed for delivery,
please immediately call Customer Service at
(570) 546-9663 for advise.
The Model G0664 is
an extremely heavy
machine. Serious per-
sonal injury may occur if
safe moving methods are
not followed. To be safe,
you will need assistance
and power equipment
when moving the ship-
ping crate and remov-
ing the machine from the
crate.
save the containers and all packing materials for
possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
When you are completely satisfied with the condi-
tion of your shipment, you should inventory the
contents.
CUTTING HAzARD!
Blades are sharp! put
on heavy leather gloves
when handling a blade
or making adjustments
near a blade or cutter!
-12-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Inventory
d
C
the following is a description of the main compo-
nents shipped with your machine. lay the compo-
nents out to inventory them.
B
e
Note: If you can't find an item on this list, check
the mounting location on the machine or examine
the packaging materials carefully. Occasionally
we pre-install certain components for shipping
purposes.
F
Machine Inventory: (figure 4)
Qty
figure 4. inventory.
A. Bandsaw (not shown)................................. 1
B. Coolant Catch tray..................................... 1
C. Work stop rod........................................... 1
D. Work stop................................................... 1
E. hex Bolts M16-2 x 50 (leveling feet)........... 4
f. hex nuts M16-2 (leveling feet) ................... 4
g
h
J
Roller Table Inventory: (figure 5)
Qty
G. Coolant reservoir Cover............................ 1
H. roller tables............................................... 2
I. lower legs................................................. 8
J. leg assemblies.......................................... 4
K. Foot assemblies......................................... 8
L. hex nuts M8-1.25..................................... 16
M. Flat Washers 8mm ................................... 16
N. hex Bolts M8-1.25 x 16 ............................ 16
O. Button head Cap screws M6-1 x 10
n
K
i
M
l
figure 5. roller table inventory.
(Coolant reservoir Cover)(not shown)...... 4
if any nonproprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
SUffOCATION HAzARD!
Immediately discard all plas-
tic bags and packing materi-
als to eliminate choking/suf-
focation hazards for children
and animals.
-13-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Recognition Chart
-14-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Clean Up
Site Considerations
the unpainted surfaces are coated with a waxy
oil to prevent corrosion during shipment. remove
this protective coating with a solvent cleaner or
degreaser, such as shown in figure 6. For thor-
ough cleaning, some parts must be removed.
for optimum performance, clean all moving
parts or sliding contact surfaces. avoid chlo-
rine-based solvents, such as acetone or brake
parts cleaner that may damage painted surfac-
es. always follow the manufacturer’s instructions
when using any type of cleaning product.
floor Load
refer to the Machine Data Sheet for the weight
and footprint specifications of your machine.
some residential floors may require additional
reinforcement to support both the machine and
operator.
placement Location
Consider existing and anticipated needs, size of
material to be processed through each machine,
and space for auxiliary stands, work tables or
other machinery when establishing a location for
your new machine. see figure 7 for the minimum
working clearances.
Gasoline and petroleum
products have low flash
points and can explode
or cause fire if used to
clean machinery. DO
NOT use these products
to clean the machinery.
52"
Many cleaning solvents
are toxic if inhaled.
Minimize your risk by only
using these products in a
well ventilated area.
106"
74"
G2544—Solvent Cleaner & Degreaser
a great product for removing the waxy shipping
grease from your machine during clean up.
figure 7. Minimum working clearances.
Children and visitors may be
seriously injured if unsuper-
vised around this machine.
Lock entrances to the shop
or disable start switch or
power connection to prevent
unsupervised use.
figure 6. Cleaner/degreaser available from
grizzly.
-15-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Moving & placing
The Model G0664 is a
heavy machine. Serious
personal injury may
occur if safe moving
methods are not used. To
be safe, get assistance
and use power equip-
ment to move the ship-
ping crate and remove
the machine from the
crate.
the base of the Model g0664 contains four lift-
ing points to allow the machine to be moved into
position.
To move the machine:
1. remove the four lag screws that mount the
machine to the pallet at the base of the ship-
ping crate.
2. insert round steel bars through the lifting
holes and attach lifting hooks and straps to
the bars as shown in figure 8.
3. lift the machine just high enough to clear the
pallet, then move it to its final location. have
an assistant stabilize the machine while mov-
ing.
—if you plan to use the leveling feet rather
than mounting the machine to the floor, set
the machine on blocks at least 4" above
the ground before putting it in the final
location, then proceed to Leveling feet on
page 18.
4. re-install the coolant reservoir cover/catch
tray.
figure 8. g0664 lifting points.
-16-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Machine Mounts
Mounting to Shop
using machine mounts, shown in figure 10, gives
the advantage of fast leveling and vibration reduc-
tion. the large size of the foot pads distributes
the weight of the machine to reduce strain on the
floor.
floor
although not required, we recommend that you
mount your new machine to the floor. Because
this is an optional step and floor materials may
vary, floor mounting hardware is not included.
generally, you can either bolt your machine to
the floor or mount it on machine mounts. Both
options are described below. Whichever option
you choose, it is necessary to level your machine
with a precision level.
Bolting to Concrete floors
lag shield anchors with lag bolts and anchor
studs (figure 9) are two popular methods for
anchoring an object to a concrete floor. We sug-
gest you research the many options and methods
for mounting your machine and choose the best
that fits your specific application.
figure 10. Machine mount example.
NOTICE
We strongly recommend securing your
machine to the floor if it is hardwired to the
power source to avoid conduit damage from
accidental machine movement. Consult with
your electrician to ensure compliance with
local codes.
NOTICE
Anchor studs are stronger and more per-
manent alternatives to lag shield anchors;
however, they will stick out of the floor,
which may cause a tripping hazard if you
decide to move your machine.
anchor stud
lag shield & lag Bolt
figure 9. typical fasteners for mounting to
concrete floors.
-17-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Leveling feet
Machine Leveling
each corner of the Model g0664 base has a foot
with a threaded hole that can be used to level the
machine.
Whether you mount the machine to the shop floor,
use machine mounts, or use the leveling feet, the
Model g0664 must be leveled before use.
To install the leveling feet:
To level the machine:
1. place the machine on blocks at least 4"
above the ground so that each threaded hole
can be accessed from underneath.
1. using a level placed on the vise table as a
guide, level the machine by adjusting one
side up or down as needed, using shims,
machine mounts, or the leveling feet. Be sure
to adjust each side in small, equal increments
as one adjustment also affects the other
side.
2. insert one M16-2 x 50 hex bolt with an M16-2
hex nut into each of the feet, as shown in
figure 11.
2. once the machine is level in one direction,
rotate the level 90˚ and check again for
level.
3. again adjust the machine as needed. Be sure
to use small, equal increments on each side.
4. re-check for level in both the left-to-right and
front-to-rear directions. re-adjust if neces-
sary.
hex nut
5. once the machine is level, secure the mount-
ing hardware as necessary, depending on
the mounting method you have chosen.
hex Bolt
figure 11. Leveling feet.
3. lift the machine, remove the blocks, then
place the machine into its final location.
4. proceed to Leveling Machine.
-18-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
3. attach a leg assembly to the under-side
of each end of both roller tables with four
M8-1.25 x 16 hex bolts, four 8mm flat wash-
ers, and four M8-1.25 hex nuts (figures 14
–15).
Roller Table
Assembly
the Model g0664 comes with two auxiliary roller
tables to support long workpieces during opera-
tion.
leg assembly
roller table
To assemble the roller tables:
1. insert one lower leg into the upper leg assem-
bly, as shown in figure 12. tighten one of
the cap screws to temporarily hold the leg in
place. repeat for the other seven legs.
lower leg
figure 14. Placing legs on roller table.
leg assembly
roller table
upper leg assembly
figure 12. lower leg attachment.
2. thread one foot assembly into one of the
lower legs, as shown in figure 13. repeat for
the other seven feet.
x4
figure 15. Attaching legs to roller table.
Foot assembly
lower leg
figure 13. Foot attachment.
g0664 heavy duty Metal-Cutting Bandsaw
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Flip the completed roller tables onto their feet
and place them on either side of the saw, as
shown in figure 16.
Required
Adjustments
to ensure your safety and to prevent damage to
the machine, you must adjust the blade tension
before the Test Run.
Blade tension (page 36) is not set at the factory
to prevent unnecessary stress on the blade dur-
ing shipping. if the Test Run is performed without
first properly tensioning the blade, the blade may
come off, resulting in personal injury or damage to
the blade or machine.
to properly tension the blade, turn the blade ten-
sion handwheel until the blade tension gauge
reads between 25,000 and 28,000 psi (page
36).
figure 16. Positioning roller tables.
5. place a long straightedge across the saw
table and roller tables and adjust the legs so
that the roller tables are even with the saw
table.
6. tighten all (16) leg cap screws.
Coolant Reservoir
Cover/Catch Tray
attach the coolant reservoir cover/catch tray to the
machine with the four M6-1 x 10 button head cap
screws (figure 17).
screws
reservoir Cover tray
figure 17. Coolant reservoir cover/catch tray.
-20-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Test Run
Before starting the saw, make sure you
have performed the preceding assembly
and adjustment instructions, and you have
read through the rest of the manual and
are familiar with the various functions and
safety features on this machine. failure to
follow this warning could result in serious
personal injury or even death!
once the assembly is complete, test run your
machine to make sure it runs properly and is
ready for regular operation.
the test run consists of verifying the following: 1)
the motor powers up and runs correctly, 2) the
stop button safety feature works correctly, and 3)
the motor turns the correct direction (machine is
not wired out of phase).
To test run the machine:
if, during the test run, you cannot easily locate
the source of an unusual noise or vibration, stop
using the machine immediately, then review
Troubleshooting on page 43.
1. Make sure you understand the safety instruc-
tions at the beginning of the manual and the
machine is setup properly.
2. Make sure all tools and objects used during
setup are cleared away from the machine.
if you still cannot remedy a problem, contact our
tech support at (570) 546-9663 for assistance.
3. Make sure that you verify the Required
Adjustments listed on page pB.
refer to the diagram below during the test run
procedure.
4. Fill the cutting fluid reservoir with cutting fluid
(page 30) if you have not already. do not
run the pump without cutting fluid or you will
damage it.
HI6C9ꢀ7N
A
B
F
D
H
K
C
G
5. Connect the machine to the power source.
HIDE
HI6GI
6. push the safety stop button ( , K) in, then
11ꢀ>
twist it clockwise so it pops out. When the
stop button pops out, the switch is reset
and ready for operation (see figure 19).
E
I
D;;
M
ADL
=><=
HIDE
J
L
%
&
)
.
+
34/0 "UTTON
figure 19. resetting the switch.
-
,
'
(
*
figure 18. Control panel.
-21-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
7. turn the main ON/Off switch (M) ON.
—investigate and correct strange or unusual
noises or vibrations before operating the
machine further. always stop the machine
and disconnect it from power before inves-
tigating or correcting potential problems.
D;;
ADL
=><=
8. turn the blade speed switch ( , i) to the
"low" position.
11ꢀ>
9. press the standby button ( , F). you should
HIDE
16. press the stop ( , K) button to stop the
hear the hydraulic motor (located in the
machine.
machine base) turn on.
17. Without resetting the switch, press the
10. Verify that the power is not connected out of
phase by checking that the hydraulic motor is
turning the correct direction, using the criteria
below:
11ꢀ>
standby button (
, F), the vise close button
HI6GI
(
, g), then the start button (
, e). the
machine should not start.
—if the machine does not start, the safety
stop button safety feature is working cor-
rectly.
—if the raise bow button (
, d) raises the
bow when pressed, the machine is wired
in phase.
—if the machine does start (with the stop
button pushed in), immediately disconnect
power to the machine. the safety stop
button safety feature is not working correct-
ly. this safety feature must work properly
before proceeding with regular operations.
Call tech support for help.
—if the raise bow button (
, d) makes an
audible click but does not move the saw
bow, the machine is wired out of phase.
stop the machine, disconnect the machine
from power, then swap any two of the three
power wires that connect to the machine.
11. Check the function of the saw bow hydraulics
by pressing the raise bow button (
, d)
and the lower bow button ( , h).
Recommended
Adjustments
12. Check the function of the vise hydraulics by
pressing the vise open button ( , C) and the
vise close button ( , g).
For your convenience, the adjustments listed
below have been performed at the factory.
13. Check the function of the cutting fluid pump
by turning the cutting fluid pump switch
(
, B) left and right.
Because of the many variables involved with ship-
ping, however, we recommend that you at least
verify the following adjustments to ensure the best
possible results from your new machine before
putting it into use.
14. With the blade in the upmost position, press
the vise close ( , g) button.
Note: As a safety precaution, the saw motor
will not start unless the vise close button is
pressed first.
factory adjustments that should be verified:
•
Blade tension (not set at factory. refer to
page 36).
15. start the blade movement by pressing the
HI6GI
start button (
, e) while keeping your
HIDE
finger near the safety stop button ( , K).
•
•
Feed stop (refer to page 51).
—When operating correctly, the machine
runs smoothly with little or no vibration or
rubbing noises.
limit switches (refer to page 51).
-22-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: OpERATIONS
Operation Safety
To reduce the risk of
serious injury when using
this machine, read and
understand this entire
manual before beginning
any operations.
Loose hair, clothing, or
jewelry could get caught
in machinery and cause
serious personal injury.
Keep these items away
from moving parts at all
times to reduce this risk.
NOTICE
Damage to your eyes could result from using
this machine without proper protective gear.
Always wear safety glasses or a face shield
when operating this machine.
If you have never used this type of machine
or equipment before, WE STRONGLY REC-
OMMEND that you read books, trade maga-
zines, or get formal training before begin-
ning any projects. Regardless of the con-
tent in this section, Grizzly Industrial will
not be held liable for accidents caused by
lack of training.
-23-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Vise Handwheel: opens/closes the vise.
Basic Controls
Vise Quick Release: releases the vise to
allow rapid opening/closing without using the
handwheel.
use the descriptions and figures below to become
familiar with the basic controls of your machine.
Vise position Lock: locks the vise in position to
prevent lateral movement during use.
Blade Tension Gauge: displays the current
blade tension.
Blade Tension Handwheel: tensions the blade
during use and releases tension for storage or
replacement.
Vise handwheel
Blade Guide Lock Handle: locks/releases the
upper blade guide.
Blade tension gauge
Blade tension handwheel
Vise Quick release
Vise position lock
figure 22. Vise controls.
Blade guide lock handle
figure 20. Blade controls.
Saw Angle Scale: indicates the current angle of
cut.
Saw Angle Lock: locks the saw angle in position
to prevent movement during use.
saw angle scale
saw angle lock
figure 21. Saw angle controls.
-24-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Control panel
d
h
K
C
B
a
e
F
g
M
i
J
l
figure 23. G0664 control panel.
H. Lower Bow Button (
): hydraulically
A. power Indicator Light: indicates the main
power to the machine is turned ON.
lowers the saw blade at the rate determined
by the downfeed knob (l).
B. Cutting fluid Switch (
): turns the cut-
D;;
ADL
=><=
I. Blade Speed Switch ( ): Controls the
speed of the blade (LOW/OFF/HIGH).
ting fluid pump to Manual/OFF/Auto.
C. Vise Open Button ( ): hydraulically
3
J. Laser Light ON/Off Switch ( ): turns the
laser alignment function ON/OFF.
opens the vise approximately ⁄8" to release
workpieces between cuts.
HIDE
K. Safety STOp Button ( ): When pressed,
D. Raise Bow Button (
): hydraulically
turns OFF saw motor, hydraulic motor, and
cutting fluid motor. does not Cut poWer
to MaChine! to reset, turn the button
clockwise until it pops back out.
raises the saw blade. Will continue raising the
blade until the upper limit switch is reached or
the button is released.
HI6GI
E. Saw Motor Start Button (
): turns the
%
&
.
'
-
,
(
L. Blade Downfeed Knob ( ): Controls
saw motor ON/OFF.
)
+
*
the rate at which the blade feeds into the
workpiece.
11ꢀ>
f. Standby Button (
): powers control panel
and readies all functions for use. Must be
pressed after safety stop button is reset.
M. ON/Off Switch: turns machine ON/OFF.
G. Vise Close Button ( ): hydraulically closes
3
the vise approximately ⁄8". Must be activated
before saw motor will turn ON.
-25-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
3. locate the 0° stop bracket and swivel it out
of the way, as shown in figure 25. this will
allow the bow to rotate past 0°.
Cutting Angle
your bandsaw has a locking turret with a range of
-45° to 60°.
To set the cutting angle between 0° and 60°:
1. raise the bow high enough to clear the vise
and press the emergency stop button to pre-
vent accidental startup.
2. loosen the saw angle lock lever, rotate the
saw bow to the desired angle, as indicated by
the scale, then re-tighten the swivel lock lever
(figure 24).
0° stop Bracket
figure 25. 0° stop bracket.
4. loosen the vise position lock lever and slide
the vise assembly to the right side of the saw
table (figure 26).
scale
saw angle lock lever
figure 24. saw angle lock lever.
To set the cutting angle between 0° and -45°:
1. raise the bow high enough to clear the vise
and press the emergency stop button to pre-
vent accidental startup.
Vise position lock lever
figure 26. positioning Vise.
2. loosen the saw angle lock lever, and rotate
the bow to approximately 45°.
5. rotate the saw bow to the desired angle, as
indicated by the scale, then re-tighten the
swivel lock lever. Make sure the vise is clear
of the path of the saw before proceeding.
-26-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Coolant Catch Tray Blade Guide position
use the coolant catch tray to reduce cutting fluid
lost at the end of a workpiece or when cutting at
steep angles. the catch tray fits over the lip of the
base as illustrated in figure 27.
the blade guide supports the blade during opera-
tion and the attached blade guard protects the
operator from the exposed portion of the blade.
therefore, proper positioning is important for
accurate and safe operations.
To position the blade guide:
8ViX]ꢀIgVn
1. place the workpiece in the vise and clamp it
in position.
BVX]^cZꢀ7VhZ
Catch tray
2. lower the saw bow until the blade is just
above the workpiece.
3. disConneCt BandsaW FroM poWer!
upper Blade guide
figure 27. Catch tray installation.
Blade guide lock lever
figure 28. Blade guide and lock lever.
4. loosen the blade guide lock lever,
5. slide the blade guide as close to the workpiece
as possible, making sure the blade guide will
not contact the workpiece during operation.
6. tighten the blade guide lock lever.
-27-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Workstop
Vise
the Model g0664 has an adjustable workstop
that is easy to install and use.
the Model g0664 vise is hydraulically assisted.
once the vise jaws are manually positioned close
to the workpiece, the vise open/close buttons
can be used to quickly and easily release and re-
clamp the workpiece hydraulically during repeti-
tive operations.
To install the workstop:
1. thread the workstop rod into the base and
tighten.
To use the vise:
2. slide the workstop onto the rod.
1. raise the bow (
).
lock
hex Bolt
2. press the vise open button ( ).
Jam nut
Knob
3. insert the workpiece between the jaws.
4. use the handwheel (figure 30) to move the
1
jaws to within ⁄4" of the workpiece.
Workpiece
handwheel
Workstop rod
set screw
Workstop
figure 29. Workstop assembly.
3. Measure the distance from the blade to the
workstop, slide the workstop to the needed
position, then tighten the set screw.
Note: Fine adjustments can be made by
loosening the jam nut, adjusting the hex bolt
as needed, then re-tightening the jam nut.
figure 30. Vise options and controls.
5. use the vise close button ( ) to clamp the
workpiece. Between cuts, use the open vise
button ( ) to release and reposition/reload
a new workpiece.
Note: As a safety precaution, the vise close
button (
) must be pressed before the saw
motor will start.
-28-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
6. use the chart shown in figure 31 as a guide
to quickly position the workpiece between
the vise jaws correctly and to avoid slipping
during a cut. do not Cut steel that
is staCKed or Bundled. one or more
workpieces will slip and damage the saw
blade.
Always turn the saw OFF and allow the blade
to come to a complete stop before using the
vise! failure to follow this caution may lead
to injury.
./4
2%#/--%.$%$
2%#/--%.$%$
figure 31. Vise clamping options.
-29-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Wearing gloves, use a rag to remove any
chips and foreign material that may have
fallen inside the reservoir during shipping and
machine use.
Cutting fluid System
4. Fill the reservoir with your chosen cutting fluid
solution and replace the reservoir cover.
fIRE HAzARD! DO NOT
cut magnesium when
using oil-water solutions
as a cutting fluid! Only use
a cutting fluid intended for
magnesium. The water in
the solution may cause a
magnesium-chip fire.
5. turn the cutting fluid pump switch (
) to
the low pressure position ( ), and adjust the
valves on the cutting fluid hoses to control the
flow of cutting fluid (see figure 33).
Note: Too much flow at the fluid nozzle will
make a mess and can make the work area
unsafe; and not enough fluid at the cut will
overheat the blade, causing the blade teeth
to load up and break.
this bandsaw has a built-in cutting fluid system
that extends the life of your bandsaw blades
by lowering the temperature of the blade and
workpiece.
Fluid nozzle
Valve
the cutting fluid pump has two modes controlled
by the switch on the control panel. the low-pres-
sure setting ( ) is used to supply cutting fluid
directly to the blade through the fluid nozzles. the
high-pressure setting ( ) is used to supply high
pressure to the auxiliary sprayer for rinsing metal
chips into the reservoir.
see Cutting fluid Tips on page 31 for additional
information regarding selection and use.
To use the cutting fluid system:
figure 33. Cutting fluid control valve.
1. disConneCt BandsaW FroM poWer!
2. remove the screws and the reservoir cover
tray (figure 32).
NOTICE
NEVER operate the pump with the reservoir
below the low mark or you will over-heat the
pump and void your warranty!
screws
6. Monitor the cutting fluid level frequently to
keep the system working properly. do not
let the cutting fluid pump run dry.
reservoir Cover tray
drain plug
figure 32. Cutting fluid system reservoir and
cover.
-30-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the selections below to choose the appro-
priate cutting fluids:
Cutting fluid Tips
•
For cutting low alloy, low carbon, and gen-
eral-purpose category metals with a bi-metal
blade—use a water soluble cutting fluid.
pOISON & BIOLOGICAL
HAzARD! Use the proper
•
For cutting stainless steels, high carbon, and
high alloy metals, brass, copper and mild
steels—use "neat Cutting oil" (commonly
undiluted mineral oils) that have extreme
pressure additives (ep additives).
personal
protection
equipment when handling
cutting fluid and dispose
by following federal, state,
and fluid manufacturer
requirements to properly
dispose of cutting fluid.
•
For cutting cast iron, cutting fluid is not rec-
ommended.
Remember: too much flow at the cutting fluid
nozzle will make a mess and can make the work
area unsafe; and not enough fluid at the cut will
overheat the blade, causing the blade teeth to
load up and break.
While simple in concept and function, many
issues must be taken into account to find and use
the correct cutting fluid. For example, you must
consider the workpiece type and hardness, its
shape, the blade feed rate, blade tpi, the tooth
type, and blade type, and cutting speed. always
follow all product warnings and contact the fluid
manufacturer for unanswered questions.
-31-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade pitch (TpI)
Blade Selection
the chart below is a basic starting point for choos-
ing teeth per inch (tpi) for variable tooth pitch
blades and standard raker set bi-metal blades/
hss blades. however, for exact specifications of
bandsaw blades that are correct for your opera-
tion, contact the blade manufacturer.
selecting the right blade for the cut requires a
knowledge of various blade characteristics.
Blade Terminology
To select the correct blade pitch:
a
1. Measure the material thickness. this mea-
surement is the length of cut taken from
where the tooth enters the workpiece, sweeps
through, and exits the workpiece.
B
C
2. refer to the "Material Width/diameter" row of
the blade selection chart in figure 35, and
read across to find the workpiece thickness
you need to cut.
d
e
F
h
Material Width/
diameter
g
i
bb
*%
^cX]
'
figure 34. Bandsaw blade terminology.
Material shapes
*$-
)$+
(
A. Kerf: the width of cut made by the blade dur-
ing cutting.
($)
'$(
,*
)
*
+
,
-
.
&%
&&
&'
&(
&)
&*
&+
&,
&-
&%%
&*%
'%%
B. Tooth Set: the distance each tooth is bent
left or right from the blade edge.
($)
'$(
Blade pitch
Chart
'*%
(%%
C. Gauge: the thickness of the blade (not
including the tooth set).
&#)$
'#*
D. Blade Width: the widest point of the blade
measured from the tip of the tooth to the back
edge of the blade.
(*%
)%%
)*%
&#*$
#-
ideal Blade teeth
per inch (tpi)
E. Tooth Rake: the angle of the tooth face
from a line perpendicular to the length of the
blade.
&.
figure 35. general guidelines for blade selection
and speed chart.
f. Gullet Depth: the distance from the tooth tip
to the bottom of the curved area (gullet).
3. refer to the "Material shapes" row and find
the shape of the material to be cut.
G. Tooth pitch: the distance between tooth
tips.
4. in the applicable row, read across to the right
and find the box where the row and column
intersect. listed in the box is the minimum
tpi recommended for the variable tooth pitch
blades.
H. Blade Back: the distance between the bot-
tom of the gullet and the back edge of the
blade.
I. TpI: the number of teeth per inch measured
from gullet to gullet.
-32-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Length
Setting feed Rate
Measured by the blade circumference, blade
lengths are usually unique to the brand of your
bandsaw and the distance between the wheels.
the Model g0664 uses a 129"–131" blade.
Feed rate is the speed at which the bow lowers
and the saw blade cuts through a workpiece. the
feed rate dial adjusts the feed rate. if a lubricant is
used while cutting, the feed rate can be increased
by approximately 15%.
Blade Width
Measured from the back of the blade to the tip of
the blade tooth (the widest point), blade width is
often the first consideration given to blade selec-
tion. Blade width dictates the largest and smallest
curve that can be cut, as well as how accurately
it can cut a straight line—generally the wider the
blade, the straighter it will cut. the Model g0664
uses a 11⁄16" wide blade.
To set the feed rate:
1. raise the bow to the upmost position by
pressing the raise bow button (
).
%
&
.
'
(
-
,
2. set the feed rate dial (
) to the desired feed
)
+
*
rate; 0 (fully clockwise) is the slowest and 9
(fully counterclockwise) is the fastest (figure
36).
Feed rate dial
figure 36. Feed rate dial.
3. proceed with cutting operations.
4. observe the metal chips produced by the cut
and refer to Chip Inspection Chart on page
35 for information on how to adjust your feed
rate for optimum cutting performance.
-33-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Speed
Blade Speed
NOTICE
DO NOT change motor speed during a cut
as this may overload a series of engaged
blade teeth, resulting in damage to the
blade and possible blade breakage.
the Model g0664 has a two-speed control with
settings of 160 and 320 feet per minute (FpM).
the speed is controlled by a rotary switch and
can be switched while the motor is operating. the
speed should not be switched during a cut.
the table shown in figure 37 is a sampling of
speed rates for various materials. use these as a
guideline, and use the cutting fluid system on your
bandsaw to get the most life from your blades.
BViZg^Vaꢀ
8deeZgꢀ
6aadnhꢀ
6aadnꢀ6HIBꢀCjbWZgꢀ
7aVYZꢀHeZZYꢀ
BViZg^Va
C^X`aZ
8]gdbZ
BdanWYZcjb -+)%
6aadnh :.(&%
6aadnꢀ6HIBꢀCjbWZg
7aVYZꢀHeZZY
&,(!.('ꢀ
((%!(+*ꢀ
+'(!+')ꢀ
'(%!'+%!','ꢀ
'-%!'+)!+('!+**ꢀ
&%&!&%'!&&%!&''!&,'ꢀ
&,*&!&-'!''%!*&%ꢀ
+'*!ꢀ,%+!ꢀ,&*!ꢀ.()ꢀ
+(%ꢀ
=^ꢀ
=^ꢀ
=^ꢀ
Adꢀ
Adꢀ
Adꢀ
Adꢀ
Adꢀ
Adꢀ
Adꢀ
=^ꢀ
=^ꢀ
=^ꢀ
=^ꢀ
=^ꢀ
=^ꢀ
=^ꢀ
=^ꢀ
=^ꢀ
=^ꢀ
Adꢀ
Adꢀ
Adꢀ
Adꢀ
-+&*!ꢀ-+'%!ꢀ-+''
)()%!ꢀ:)()%!ꢀ-+(%
=^
Ad
Ad
Ad
Ad
Ad
Ad
Ad
Ad
Ad
Ad
Ad
Ad
Ad
Ad
Ad
Ad
Ad
Ad
Ad
IddaꢀHiZZah 6"+
6"'
6"&%
9"'
="&&!="&'!="&(
)'%
)(%
)&%!*%'
)&)
)(&
))%8
(%)!ꢀ(')
(%)A
-&&ꢀ
&&&,ꢀ
&&(,ꢀ
HiV^caZhh
HiZZah
8VgWdcꢀ
HiZZahꢀ
&&)&!&&))ꢀ
&&)&ꢀ=^\]ꢀHigZhhꢀ
&%(%ꢀ
&%%-!&%&*!&%'%!&%'*ꢀ
&%(*ꢀ
&%&-!&%'&!&%''ꢀ
&%'+!&*&(ꢀ
6(+ꢀꢁH=6E:Hꢂ!&%)%ꢀ
&%)'!&*)&ꢀ
&%))!&%)*ꢀ
&%+%ꢀ
(),
(&+!ꢀ(&+A
)&+
&%.*ꢀ
figure 37. Material speed table.
-34-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
chip inspection chart
Chip Inspection Chart
the best method of evaluating the performance of your cutting operation is to inspect the chips that are
formed. refer to the chart below for chip inspection guidelines.
Chip
Appearance
Chip
Description
Chip
Color
Blade
Speed
feed
Rate
feed
pressure
Additional
Actions
thin & Curled
silver
Good
Good
Good
hard, thick &
short
Brown or Blue decrease
Brown or Blue decrease
decrease decrease
decrease decrease
hard, strong &
thick
hard, strong & silver or light
decrease decrease Check Blade
Good
increase
Good
thick
Brown
slightly
slightly
pitch
Check Blade
pitch
hard & thin
silver
decrease decrease
straight & thin
powdery
silver
silver
silver
increase
increase
increase
increase
decrease
Good
Curled tight &
thin
Check Blade
pitch
decrease decrease
figure 38. Chip inspection chart.
-35-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Tensioning
Blade Tensioning
Blade Care &
Break-In
NOTICE
Blade Care
To prolong blade life, release the tension on
the blade if the machine will be idle for an
extended period of time.
a bandsaw blade is a delicate piece of steel that
is subjected to tremendous strain. you can obtain
longer use from a bandsaw blade if you give it fair
treatment and always use the appropriate feed
rate for your operation.
proper blade tension reduces the risk of blade
breakage and improves cutting performance.
Be sure to select blades with the proper width, set,
type, and pitch for each application. the wrong
choice of blades will often produce unnecessary
heat and will shorten the life of your blade.
Note: The most accurate way to check blade ten-
sion is to use the Model H5408 Blade Tensioning
Gauge (see Accessories on Page 39).
to tension the blade, turn the blade tension
handwheel until the blade tension gauge reads
between 25,000 and 28,000 psi.
a clean blade will perform much better than a dirty
blade. dirty or gummed up blades pass through
the cutting material with much more resistance
than clean blades. this extra resistance also
causes unnecessary heat.
Blade Break-In
the sharp teeth tips and edges of a new blade are
extremely sharp, and cutting at full feed rate may
cause fracturing of the beveled edges of the teeth
and premature blade wear.
To properly break-in a new Grizzly blade:
1. Choose the correct speed for the blade and
material of the operation.
2. reduce the feed pressure by half for the first
50–100 in2 of material cut.
3. to avoid twisting the blade when cutting,
adjust the feed pressure when the total width
of the blade is in the cut.
4. use the Chip Inspection Chart on page 35
to check the blade efficiency.
-36-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Breakage
Workpiece
Inspection
Many conditions may cause a bandsaw blade to
break. Blade breakage is unavoidable, in some
cases, since it is the natural result of the peculiar
stresses that bandsaw blades must endure. Blade
breakage is also due to avoidable circumstances.
avoidable blade breakage is most often the result
of poor care or judgement on the part of the
operator when mounting or adjusting the blade or
support guides.
some metal workpieces are not safe to cut with a
metal cutting bandsaw; instead, a different tool or
machine should be used.
Before cutting, inspect the material for any of
the following conditions and take the neces-
sary precautions:
•
Small or Thin Workpieces: small or thin
workpieces may be damaged during cut-
ting—avoid cutting these workpieces if possi-
ble. if you must cut a small or thin workpiece,
attach it to or clamp it between larger scrap
pieces that will both support the workpiece
through the cut. some thin sheet metals will
not withstand the forces from this bandsaw
during cutting; instead, use a shear, nibblers,
or sheet metal nippers to cut these pieces.
The most common causes of blade breakage
are:
•
Faulty alignment or adjustment of the blade
guides.
•
•
•
•
Feeding the blade too fast.
dull or damaged teeth.
over-tensioned blade.
•
Unstable Workpieces: Workpieces that can-
not be properly supported or stabilized with
the vise should not be cut on this bandsaw.
examples are chains, cables, workpieces
with internal or built-in moving or rotating
parts, etc.
top blade guide assembly set too high above
the workpiece. adjust the top blade guide
assembly so that there is approximately ½"
between the bottom of the assembly and the
workpiece.
•
•
Material Hardness: always factor in the hard-
ness of the metal before cutting it. hardened
metals will take longer to cut, may require
lubrication, and may require a different type
of blade in order to efficiently cut them.
•
•
•
•
using a blade with a lumpy or improperly fin-
ished braze or weld.
Continuously running the bandsaw when not
in use.
Tanks, Cylinders, Containers, Valves, Etc:
Cutting into containers that are pressur-
ized or contain gasses or liquids can cause
explosions, fires, caustic burns, or machine
damage. avoid cutting any of these types of
containers unless you have verified that the
container is empty and it can be properly sup-
ported during a cut.
leaving the blade tensioned when not in
use.
using the wrong pitch (tpi) for the workpiece
thickness. the general rule of thumb is to
have at least two teeth in contact with the
workpiece at all times during cutting.
•
Magnesium: pure magnesium burns eas-
ily. Cutting magnesium with a dull blade can
create enough friction to ignite the small
magnesium chips. avoid cutting magnesium
if possible.
-37-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Chips should be curled and silvery. if the
chips are thin and powder like, increase your
feed rate.
Operation Tips
the following tips will help you safely and effec-
tively operate your bandsaw and get the maxi-
mum life out of your saw blades.
•
•
Burned chips indicate a need to reduce your
blade speed.
Wait until the blade has completely stopped
before removing the workpiece from the vise,
and avoid touching the cut end—it could be
very hot!
NOTICE
Loosen blade tension at the end of each day
to prolong blade life.
•
•
•
support long pieces so they won't fall when
cut, and flag the ends to alert passers-by of
potential danger.
Tips for horizontal cutting:
•
use the work stop to quickly and accurately
cut multiple pieces of stock to the same
length.
adjust the blade guides as close as possible
to the workpiece to minimize side-to-side
blade movement.
•
•
•
Clamp the material in the vise jaws to ensure
a straight cut through the material.
use cutting fluid when possible to increase
blade life.
let the blade reach full speed before engag-
ing the workpiece.
never start a cut with the blade in contact
with the workpiece and do not start a cut on
a sharp edge.
-38-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
aCCessories
SECTION 5: ACCESSORIES
H5405—Lenox® Lube Tube™
T20534—3-4 TpI Variable pitch Blade
T20535—4-6 TpI Variable pitch Blade
T20536—5-8 TpI Variable pitch Blade
T20537—6-10 TpI Variable pitch Blade
T20538—8-12 TpI Variable pitch Blade
replacement blades for the Model g0664 heavy-
duty Metal Cutting Bandsaw. 1293⁄8" length.
lenox® lube tube™ is a stick lubricant designed
to prevent heat buildup. apply it directly to the
blade to improve overall blade life and productiv-
ity. Can be used on ferrous and non-ferrous met-
als. Biodegradeable, non-toxic, and non-staining
14.5 oz tube.
figure 39. Blades.
figure 41. lenox® lube tube™.
H5408—Blade Tensioning Gauge
the Blade tensioning gauge ensures long blade
life, reduced blade breakage, and straight cutting
by indicating correct tension. a precision dial indi-
cator provides you with a direct readout in psi.
T20677—Acculube Metalworking Lubricant
(for Medium to Heavy-Duty Machining)
this environmentally safe, non-toxic, all natu-
ral cutting fluid is idea for drilling and tapping,
machining, and sawing. it is recommended for all
ferrous metals. Made from renewable resources!
figure 40. h5408 Blade tensioning gauge.
-39-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
G5618—Deburring Tool with Two Blades
G5619—Extra Aluminum Blades
G5620—Extra Brass and Cast Iron Blade
the quickest tool for smoothing freshly machined
metal edges. Comes with two blades—one for
steel/aluminum and one for brass/cast iron.
G9256—6" Dial Caliper
G9257—8" Dial Caliper
G9258—12" Dial Caliper
these traditional dial calipers are accurate to
0.001" and can measure outside surfaces, inside
surfaces, and heights/depths. Features stainless
steel, shock resistant construction and a dust
proof display.
figure 42. g5618 deburring tool.
figure 44. grizzly® dial Calipers.
T20501—face Shield, 4" Crown, Clear
T20502—face Shield, 7" Crown, Clear
T20448—Economy Clear Safety Glasses
T20452—"Kirova" Anti-Reflective Glasses
T20456—"Dakura" Clear Safety Glasses
H0736—Shop fox® Safety Glasses
these glasses meet ansi z87.1-2003 specifica-
tions. Buy extras for visitors or employees. you
can't be too careful with shop safety!
G5562—SLIpIT® 1 Qt. Gel
G5563—SLIpIT® 12 oz Spray
used on cast iron table surfaces and other
unpainted metal surfaces to reduce sliding friction
and hangups. this product also reduces rust and
prevents resin build-up.
T20448
T20452
T20501
T20456
figure 43. our most popular eye protection.
H0736
figure 45. slipit® gel and spray.
-40-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: MAINTENANCE
Lubrication
Always disconnect power
to the machine before
all bearings and the gearbox on the Model g0664
performing maintenance.
are lubricated and sealed for life. no further atten-
failure to do this may
tion is needed unless damage occurs.
result in serious person-
al injury.
To lubricate the bandsaw:
1. lubricate the blade tensioner leadscrew
Schedule
(figure 46) with multi-purpose grease, and
apply a coat of high-quality metal protectant
such as slipit® on page 40 to all unpro-
For optimum performance from your machine,
follow this maintenance schedule and refer to any
specific instructions given in this section.
tected cast iron surfaces.
Blade tensioner lead screw
After first 50 hours:
•
Change hydraulic fluid.
Daily Check:
•
•
•
•
•
•
loose mounting bolts.
damaged or worn saw blade.
Worn or damaged wires.
proper blade tension.
hydraulic/cutting fluid level.
Clean and wipe down machine.
Monthly Check:
•
lubricate vise and blade tensioner leadscrew.
figure 46. lubrication point.
Six-Month Check:
•
Change hydraulic fluid.
2. lubricate the leadscrew as needed with multi-
purpose grease by applying a thin layer along
the leadscrew surface (see figure 47).
Annual Check:
•
replace cutting fluid and clean out tank. if
the saw is used heavily, clean the tank and
replace the cutting fluid at shorter intervals.
Cleaning
Cleaning the Model g0664 is relatively easy. after
using your bandsaw, clean excess chips by vacu-
uming or sweeping them up.
Vise
lead
if using water based cutting fluid, wipe down and
lubricate areas where the liquid may collect and
cause corrosion.
screw
figure 47. Vise leadscrew lubrication area.
-41-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
4. remove the tank vent cap.
Hydraulic System
5. Clean the tank vent with mineral spirits and
let air dry.
Checking Hydraulic fluid
6. Clean the tank screen with mineral spirits and
blow dry with compressed air.
1. Check the fluid level gauge located on the
side of the tank. (figure 48). the fluid level
indicator should be above half.
7. inspect the screen and tank vent for any
holes and replace if any damage exists.
—if the fluid level is low, add until it is full.
8. open the tank by removing the hex bolts that
secure the lid.
9. Wipe out as much residual fluid and contami-
nants from the tank as possible. We highly
recommend that the tank be cleaned out with
a pressure washer or steam cleaner and fully
dried with compressed air for best results.
Fluid level
indicator
10. reinstall the tank lid and screen.
11. replace the drain plug, then fill the tank with
15 liters of iso 15 or equivalent fluid, then
reinstall the tank vent cap.
Fluid level
gauge
figure 48. Hydraulic fluid tank gauge.
tank Vent Cap
tank screen
2. inspect for burnt-smelling or tan-colored,
water-contaminated hydraulic fluid. if the fluid
is contaminated, clean the tank filter/strainer,
flush the system, and replace the fluid.
Changing Hydraulic fluid (figure 49)
tank lid
drain plug
Always wear safety gog-
gles when servicing the
hydraulic system.
figure 49. Hydraulic fluid tank.
Hydraulic fluid Type
Qty
iso 15 or equivalent...................................... 15l
1. disConneCt BandsaW FroM poWer!
2. unbolt and remove the tank, then place it on
blocks high enough to get a 3 gallon drain
pan under it.
3. remove the drain plug and allow the tank to
empty into the drain pan.
-42-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
service
SECTION 7: SERVICE
review the troubleshooting and procedures in this section to fix or adjust your machine if a problem devel-
ops. if you need replacement parts or you are unsure of your repair skills, then feel free to call our technical
support at (570) 546-9663.
Troubleshooting
Motor & Electrical
SYMpTOM
pOSSIBLE CAUSE
CORRECTIVE ACTION
Machine does not start or a 1. safety stop button pressed.
1. twist safety stop button until it pops out.
breaker trips.
2. Machine is wired out of phase (only 2. ensure correct size for machine load;
if this is the first time the machine is
run).
replace weak breaker.
3. Wall fuse/circuit breaker is blown/ 3. Check for broken wires or disconnected/corroded
tripped.
connections, and repair/replace as necessary.
4. Wiring is open/has high resistance. 4. test for good contacts; correct the wiring.
5. plug/receptacle is at fault or wired 5. Correct wiring.
incorrectly.
6. Motor connection wired incorrectly. 6. Correct motor wiring connections.
7. power supply is at fault/switched 7. ensure hot lines have correct voltage on all legs and
OFF.
main power supply is switched ON.
8. replace faulty on/oFF switch.
9. test/repair/replace.
8. Motor on/oFF switch is at fault.
9. Motor is at fault.
Machine stalls or is over- 1. Wrong blade for the workpiece 1. use blade with correct properties for your type of cut-
loaded
material.
ting.
2. Wrong workpiece material.
2. use metal with correct properties for your type of cut-
ting.
3. Feed rate/cutting speed too fast for 3. decrease feed rate/cutting speed.
task.
4. Blade is slipping on wheels.
5. incorrect power supply voltage.
6. Motor bearings are at fault.
4. adjust blade guides and tension.
5. ensure hot lines have correct voltage on all legs.
6. test by rotating shaft; rotational grinding/loose shaft
requires bearing replacement.
7. plug/receptacle is at fault.
7. test for good contacts; correct the wiring.
8. Motor connection is wired incor- 8. Correct motor wiring connections.
rectly.
9. Motor has overheated.
10. Motor is at fault.
9. Clean off motor, let cool, and reduce workload.
10. test/repair/replace.
Machine has vibration or 1. Motor fan is rubbing on fan cover.
noisy operation.
1. replace dented fan cover; replace loose/damaged
fan.
2. Blade is at fault.
2. replace/resharpen blade.
3. rebuild gearbox for bad gear(s)/bearing(s).
4. Change blade.
3. Worm gear is at fault.
4. Wrong blade for material.
5. speed is set too slow.
5. adjust speed as required.
-43-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Bandsaw Operations
SYMpTOM
pOSSIBLE CAUSE
CORRECTIVE ACTION
Machine is loud when
cutting or bogs down in
the cut.
1. excessive feed rate or blade
speed.
1. refer to Setting feed Rate on page 33,
or Blade Speed on page 34 and adjust as
required.
2. refer to Blade Selection on page 32 and adjust as
required.
2. the blade tpi is too great, or the
material is too coarse.
Blades break often.
1. Blade is not tensioned correctly.
1. Check to see that blade is not excessively tight or
too loose.
2. the workpiece is loose in the vise. 2. Clamp the workpiece tighter, or use a jig to hold the
workpiece.
3. the feed or cut speed is wrong.
3. refer to Setting feed Rate on page 33, or Blade
Speed on page 34, and adjust as required.
4. refer to Blade Selection on page 32, and adjust
as required.
4. the blade tpi is too great, or the
material is too coarse.
5. the blade is rubbing on the wheel 5. refer to Squaring Blade on page 49, and adjust
flange.
as required.
6. the bandsaw started with the
blade resting on the workpiece.
7. the guide bearings are
misaligned, or the blade is rubbing
on the wheel flange.
6. start bandsaw and then slowly lower the headstock
by Setting feed Rate on page 33.
7. refer to Squaring Blade on page 49, or Blade
Guides on page 47, and adjust as required.
8. the blade is too thick, or the
blades are of low quality.
8. use a higher quality blade.
Blade dulls prematurely.
1. the cutting speed is too fast.
1. refer to Blade Speed on page 34, and adjust as
required.
2. the blade tpi is too coarse.
2. refer to Blade Selection on page 34, and adjust
as required.
3. the blade feed pressure is too
light.
3. refer to Setting feed Rate on page 33, and adjust
as required.
4. the workpiece has hard spots,
welds, or scale.
4. increase the feed pressure, and reduce the cutting
speed.
5. the blade is twisted.
6. the blade is slipping on the
wheels.
5. replace the blade.
6. refer to Blade Tension on page 36, and adjust as
required.
Blade wears on one side.
1. the blade guides are worn.
1. refer to Blade Guides on page 47 and replace or
adjust.
2. the blade guide slide bracket is
loose.
2. tighten the blade guide bracket.
3. the wheels are out of alignment.
3. refer to Squaring Blade on page 49, and adjust
as required.
teeth are ripping from the 1. the feed pressure is too heavy
1. refer to Blade Selection on page 34 and decrease
the feed pressure. refer to Setting feed Rate on
page 33, and adjust as required.
blade.
and the blade speed is too slow; or
the blade tpi is too coarse for the
workpiece.
2. the workpiece is vibrating in the
vise.
2. re-clamp the workpiece in the vise, and use a jig if
required.
3. the blade gullets are loading up
with chips.
3. use a coarser-tooth blade.
the cuts are crooked.
1. the feed pressure is too high.
1. refer to Setting feed Rate on page 33, and adjust
as required.
2. the guide bearings are out of
adjustment, or too far away from
the workpiece.
2. refer to Blade Guides on page 47 and replace or
adjust.
3. the blade tension is low.
3. refer to Blade Tension on page 36, and adjust as
required.
4. the blade is dull.
4. refer to Blade Change on page 46 and replace
the blade.
5. the blade speed is wrong.
5. refer to Blade Speed on page 34, and adjust as
required.
-44-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Hydraulic System Troubleshooting
SYMpTOM
pOSSIBLE CAUSE
CORRECTIVE ACTION
<<
hydraulics aren't function- 1. Machine is not in "standby Mode". 1. press the standby ( i) button.
ing.
2. hydraulic fluid level is low.
2. Check/fill hydraulic fluid level.
3. Wire machine in phase.
3. Machine is wired out of phase.
4. hydraulic pump motor wiring con- 4. Check/correct pump motor wiring.
nection is incorrect.
5. hydraulic system is leaking.
6. hydraulic pump is faulty.
7. Control panel wiring is faulty.
5. test for leaks/repair.
6. test/repair/replace.
7. Check that hydraulic pump motor is running and that
solenoids are activating (indicated by red led in sole-
noid plug).
Vise doesn't open/close.
1. Vise valve solenoids are faulty.
1. test/repair/replace.
2. Vise valve solenoids connections 2. Check solenoid plugs.
are bad.
3. Vise hydraulic system is leaking.
4. Vise ram is faulty.
3. test for leaks/repair.
4. test/repair/replace.
5. Control panel wiring is faulty.
5. Check that hydraulic pump motor is running and that
solenoids are activating (indicated by red led in sole-
noid plug).
saw bow doesn't raise/ 1. saw bow valve solenoids are 1. test/repair/replace.
lower.
faulty.
2. saw bow valve solenoids connec- 2. Check solenoid plugs.
tions are bad.
3. saw bow hydraulic system is leak- 3. test for leaks/repair.
ing.
4. saw bow ram is faulty.
4. test/repair/replace.
5. Control panel wiring is faulty.
5. Check that hydraulic pump motor is running and that
solenoids are activating (indicated by red led in sole-
noid plug).
-45-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Change
Change the blade when it becomes dull, damaged,
or when you are using materials that require a
blade of a certain type or tooth count.
CUTTING HAzARD!
Blades are sharp! put
on heavy leather gloves
when handling a blade
or making adjustments
near a blade or cutter!
figure 51. guards and wire brush wheel
removed.
6. loosen the blade tension handwheel and slip
the blade off of the wheels.
To change the blade on the bandsaw:
1. raise the bow enough so that the wheel
access cover can be opened.
7. install the new blade through both blade
guide assemblies and around the bottom
wheel.
2. disConneCt BandsaW FroM poWer!
8. have an assistant hold the blade on the bottom
wheel while you position it on the top wheel.
3. open the wheel access cover to expose the
blade and wheels (figure 50).
9. adjust the blade so the back of the blade is
against the shoulder of the wheels. slightly
tighten the blade tension handwheel if neces-
sary to hold the blade in place (figure 52).
Wheel access Cover
Blade
Wheel shoulder
Wheels
Blade
figure 50. Wheel access cover.
4. Fully extend the blade guide to reduce the
twisting force on the blade.
figure 52. Blade installed on wheels.
5. remove both of the blade guide guards and
the wheel brush from the bandsaw (figure
51).
10. reinstall the wheel brush, the blade guide
guards, and close the wheel access cover.
11. adjust the blade tension to 25,000 to 28,000
psi (page 36).
-46-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
5. loosen the blade guide cap screw that holds
the blade guide in position (figure 54).
Blade Guides
the blade guides have a basic factory adjustment,
but due to shipping, storage, and wear, we recom-
mend that you re-adjust the blade guides yourself
to ensure the cuts will to be your standards.
Cap screw
set screw
CUTTING HAzARD!
Blades are sharp! put
on heavy leather gloves
when handling a blade
or making adjustments
near a blade or cutter!
figure 54. Blade guide.
To adjust the blade guides:
6. loosen the set screw. this set screw controls
the inward and outward positioning of the
blade guide.
1. Make sure the blade is oiled, tensioned, and
tracking correctly.
Note: Because the blade guides must hold
the blade perpendicular to the table and at
an angle to the wheel surface, there will be
constant pressure between the blade and the
guides. The goal is to get the guides close
enough together to hold the blade straight
but not so tight so that they create excessive
friction.
2. raise the bow to the upmost position.
3. disConneCt BandsaW FroM poWer!
4. extend the blade guide as far as possible and
lock it in place (figure 53).
7. gently tighten the set screw until the blade is
just pressed flat between the blade guides.
do not force the set screw into the blade
guide.
1
8. Back the set screw out ⁄4 turn to prevent
pinching the blade.
9. tighten the blade guide cap screw.
10. loosen the blade guide assembly cap
screws.
Blade guide
figure 53. Blade guide extended.
11. adjust the blade guide assembly vertically so
that the back of the blade is just next to, but
not touching the rear blade guide, then tight-
en the blade guide assembly cap screws.
12. repeat this process for the lower blade guide
assembly.
-47-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Wheel Brush
phillip head screws
the Model g0664 is equipped with a wire wheel
brush to clean metal chips from the blade, reduc-
ing wear to the blade and machine. With use, the
wheel will wear requiring adjustment and eventual
replacement.
To adjust/replace the wheel brush:
1. raise the bow to the upmost position to allow
the best access to the wheel brush.
Wheel Brush
figure 55. Wheel brush.
2. disConneCt BandsaW FroM poWer!
4. adjust the brush so that the blade extends
3. support the wheel brush so it doesn't fall,
then loosen the two phillip head screws that
secure the wheel brush (figure 55).
1
approximately ⁄8" into the brush bristles.
—if the brush cannot be adjusted to this spec-
ification due to wear, it must be replaced.
remove the old wheel brush and position
a new one as outlined in Step 4.
5. tighten the phillip head screws to secure the
wheel brush.
-48-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade
—if the blade is square, no further adjust-
ments are necessary.
Squaring Blade
—if the blade is not square, continue with
Step 5 below.
the blade-to-table squareness is factory set.
however, due to shipping and storage we recom-
mend that you check the blade alignment yourself
to ensure the cuts will be to your standards.
5. extend the blade guide as far as possible.
Note: Perform the following step on both the
upper and lower blade guides at the same
time to maintain even force on the blade with
each blade guide.
To square the blade:
1. disConneCt BandsaW FroM poWer!
2. Make sure the blade is oiled, tensioned, and
tracking correctly, and that the guides and
stops are set.
6. loosen the two cap screws on each blade
guide assembly, then alternately adjust the
four 4mm set screws to tilt the blade guide
assembly and the blade square to the table.
3. adjust the cutting angle to 0° as indicated by
the scale.
set screws
set screws
Cap screws
Blade guide
assembly
figure 56. Bow and headstock moved to zero.
figure 58. upper blade guide adjustment.
4. place a quality square on the table and the
side of the blade (figure 57) to verify the
blade is square with the table.
set screw
square
Cap screw
figure 59. lower blade guide adjustment.
7. snug the cap screws to hold the new blade
guide setting.
table
Blade
figure 57. Checking blade squareness to vise.
-49-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Move the headstock to 60°.
Swivel Stops
6. read the scale. the bandsaw blade should
be at 60°.
the blade swivel stops are factory set. however,
due to shipping and storage we recommend that
you check the 0°, -45° and the 60° stops yourself
—if the headstock is not at 60°, adjust the
stop (figure 62) so it will line up with the
60° mark.
to ensure the cuts will to be your standards. Note:
1
The accuracy range for the scale is
⁄2° degree.
To adjust the swivel stops:
60° stop Bolt
1. Make sure the blade is oiled, tensioned, and
tracking correctly, and that the guides are
set.
2. disConneCt BandsaW FroM poWer!
3. raise the bow, move and lock the headstock
to 0° (figure 60), then lower the bow.
60° stop Bolt location
figure 62. 60° swivel stop.
7. Move and the headstock to -45°.
8. read the scale. the bandsaw blade should
be at -45°.
—if the headstock is not at -45°, adjust the
stop (figure 63) so it will line up with the
-45° mark.
0° Mark
figure 60. Bow and headstock moved to zero.
4. observe the scale, and if the headstock is not
at 0°, adjust the zero stop (figure 61) so it will
line up with the mark.
zero stop
45° stop Bolt
figure 63. 45° swivel stop.
9. go to Squaring Blade on page 49 to make
sure the cuts will be perpendicular to the
table.
figure 61. zero degree swivel stop.
-50-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
auto stop
3. loosen the auto stop knob, adjust the posi-
tion of the auto stop so it depresses the upper
limit switch button, then re-tighten the auto
stop knob. the saw bow will now automati-
cally stop when raised to this level (figure
65).
feed Stop
it may be necessary to adjust the feed stop before
making blade adjustments. the blade should
never rest on or rub on any part of the vise assem-
bly or table.
To adjust the feed stop bolt:
adjust the feed stop bolt and jam nut (figure 64),
so the bandsaw blade teeth are just below the
vise table surface when the cut is complete.
Feed auto stop
upper limit
switch
figure 65. Feed auto stop.
4. Connect the machine to power and lower the
saw bow until it contacts the feed stop bolt
(figure 64).
Jam nut
Feed stop Bolt
5. disConneCt BandsaW FroM poWer!
figure 64. Feed stop bolt.
6. adjust the lower limit switch so that the button
is depressed against the saw bow pivot base
(figure 66).
Limit Switches
the upper travel auto stop can be adjusted to
limit saw bow travel to match the height of the
workpiece. this speeds up repetitive cuts by
eliminating unnecessary saw bow travel.
saw Bow pivot Base
the lower limit switch should only be adjusted
if the blade is not passing entirely through the
workpiece or is cutting into the vise table.
To set the upper travel auto stop and lower
limit switch:
lower limit switch
figure 66. limit switch.
1. raise the saw bow to the highest level
required to provide adequate clearance for
your workpiece.
7. Connect the machine to power and test the
limit stops. if they do not stop the motion of
the saw bow at the positions desired, repeat
Steps 1– 6, fine tuning as necessary.
2. disConneCt BandsaW FroM poWer!
-51-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 8: WIRING
Electrical Safety Instructions
1. pRINTED INfORMATION. the electrical
4. CIRCUIT REQUIREMENTS. you Must fol-
low the CIRCUIT REQUIREMENTS section
on page 11. If you are unsure about the
wiring codes in your area or you plan to
connect your machine to a shared cir-
cuit, consult a qualified electrician.
information included in this section is current
at the time of printing. however, in the spirit
of improvement, we may make changes to
the electrical system of future machines.
study the photos and diagrams in this
section carefully. if you notice differences
between your machine and these diagrams,
call technical support at (570) 546-9663 for
assistance.
5. MOTOR WIRING. the motor wiring shown
in these diagrams are current at the time of
printing, but it may not match your machine.
always use the wiring diagram inside the
motor junction box.
2. SHOCK HAzARD. disconnect power from
the machine before servicing electrical com-
ponents. touching electrified parts will result
in personal injury including but not limited to
severe burns, electrocution, or death.
6. EXpERIENCING DIffICULTIES. if at any
time you are experiencing difficulties under-
standing the information included in this
section, contact our technical support at
(570) 546-9663.
3. GROUNDED CIRCUIT. electrocution or fire
could result if the machine is not grounded
and installed in compliance with electrical
codes. Compliance Must be verified by a
qualified electrician.
NOTICE
The photos and diagrams included in this
sectionarebestviewedincolor.Youcanview
electrical safety instructions
-52-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Overview
&
)
+
'
Control Box
see diagrams on page 54 and
&
images in figures 73–76 on page 56.
*
,
(
Z
Laser Light
see diagram on page 55 and
image in figure 68.
V
W
X
'
(
)
*
Hydraulic pump (Inside Stand)
see diagram on page 55 and
image in figure 67.
Saw Motor
see diagram on page 55 and
image in figure 69.
220 VAC
15-15 PLUG
Recommended
Coolant pump
see diagram on page 55 and
image in figure 71.
Y
WIRING HARNESS KEY
[
V
AVhZgꢀA^\]iꢀ=VgcZhh
Limit Switches
see diagram on page 55 and
image in figure 70.
+
,
=nYgVja^XꢀEjbeꢀ=VgcZhh
HVlꢀBdidgꢀ=VgcZhh
W
X
\
8ddaVciꢀEjbeꢀ=VgcZhh
EdlZgꢀ8dgY
Y
Z
JeeZgꢀA^b^iꢀHl^iX]ꢀ=VgcZhh
AdlZgꢀA^b^iꢀHli^X]ꢀ=VgcZhh
K^hZꢀDeZcꢀHdadcd^Yꢀ8dgY
K^hZꢀ8adhZꢀHdadcd^Yꢀ8dgY
HVlꢀJeꢀHdadcd^Yꢀ8dgY
HVlꢀ9dlcꢀHdadcd^Yꢀ8dgY
[
\
]
^
]
^
_
Solenoid Valves (Inside Stand)
see diagram on page 55 and
image in figure 72.
_
`
`
READ ELECTRICAL SAFETY
ON PAGE 52!
-53-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
diagram
Control Box Wiring Diagram
8dcigdaꢀ7dmꢀ
8dcigdaꢀEVcZa
(figure 73 on
page 56)
<gdjcY
"
&
>ccZgꢀEVcZa
"
(figure 75
on page 56)
&%
*
&(
*
&*
,
'(
&)
'
'
&
)
(
)
'
HVl
Je
K^hZ
&(
')
+
+ A& A' A( &&
-
M&ꢀꢀ M'
&%
,
'
( DeZc &
*
'(
*
,
&A& (A' *A( &(C% 6& &A&
*A( &(C% 6&
&A& (A' *A( &(C% 6&
(A'
8jii^c\
;aj^Y
DC$D;;
>cY^XVidg
A^\]i
&+
')
*
&,
*(C%
*)C%
+&C8
*(C%
*)C%
+&C8
+'C8
8dciVXidg
8"%+9&%
A6&@C&&
A6&@C&&
+'C8
)
'I& )I' +I( &)C% 6'
'I& )I' +I( &)C% 6' 'I& )I' +I( &)C% 6'
&'
8dcigda
HiVcYWn
&
.#+
BdidgꢀDc
J' K'
'( J(K( L( ) '( ')
&%#+
IZhi
*
&-
=
6
-
&&#*
Hide
GZhZi
*
)
+
*
-
AG,@%(&+
&&
'
)
K^hZ
'*
8&( 8&)
8&( 8&)
8&( 8&)
& 8adhZ(
G
H
HVl
9dlc
ꢀꢀꢀꢀꢀꢀꢀ
I
&,
&*
G
(
&
G
+
+
(
V
)
*
'
'
*
'(
L(
J(
H
K(
H
W
X
:bZg"
\ZcXn
Hide
I
)
+
I
)
AVhZg
A^\]i
DC$D;;
*
&
)
(
&
'
ꢀꢀꢀꢀꢀꢀꢀ
&-
&,
&-
&,
'(
Bdidgꢀ=^\]$D;;$Adl
Hl^iX]ꢀ+%%Kꢀ'*6
(
K'
A'
J'
Y
Z
&% &)
&' '& &+ '& ''
'&
+
'( '( '( '( '( '(
'% && &( '%
A&
A(
-
&*
.
&. *
*
*
*
&( '%
A& '( &
A(
% '(% )%%
% ')
ꢀA8:ꢀIgVch[dgbZg
A8E"I7HB
&
'
)
'
)
&
(
A&
A&
A(
&.
A'
A'
&) &+ &-
*
*
'
[
*
&&
A(
(
''
'( '( '( '( '' &.
(
\
*
BV^cꢀEdlZgꢀHl^iX]
+%%Kꢀ'*6
'(
'(
'(
'(
'( '( '( '( '' &.
]
^
&-
&+
&& &) &+ &-
*
*
_
&)
&&
`
8dcigdaꢀ7dmꢀH^YZꢀEVcZa
8dcigdaꢀ7dmꢀ7diidbꢀEVcZa
(figure 76 on page 56)
(figure 74 on page 56)
-54-
READ ELECTRICAL SAFETY
ON PAGE 52!
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Components
Components Wiring Diagram
=nYgVja^XꢀEjbeꢀBdidg
(
(figure 67)
K'
L'
J'
J&J*
K&K*
L(
L&
L*
figure 67. Hydraulic pump motor.
J(
K(
AVhZg
A^\]i
(figure 68)
'
figure 69. 220V saw motor.
figure 68. laser light.
V
)
W
&
)
)
*
&
'
X
'
(
*
+
(
+
Y
''%K
HVlꢀBdidg
Idꢀ8dcigdaꢀ7dmꢀ
K'
J'
*
(figure 69)
Z
220 VAC
3-Phase
<gdjcY
<gdjcY
8ddaVciꢀEjbe
(figure 71)
=di
=di
=di
15-15 PLUG
(as recommended)
figure 70. Limit switch.
figure 71. Coolant pump motor.
[
\
+
]
,
K^hZ
')
'(
')
'(
9H<"'%'"C"%'
K^hZꢀꢀHdaZcd^Y
K^hZ
8adhZ
DeZc
^
_
9H<"(8'"C"%'
HVlꢀHdaZcd^Y
HVl
Je
HVl
9dlc
`
AdlZg
A^b^iꢀHl^iX]
(figure 70)
JeeZg
A^b^iꢀHl^iX]
(figure 72)
figure 72.
READ ELECTRICAL SAFETY
ON PAGE 52!
-55-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Control Box Electrical Components
figure 73. Control panel wiring.
figure 75. Inner panel wiring.
figure 74. Bottom panel wiring.
figure 76. Side panel wiring.
-56-
READ ELECTRICAL SAFETY
ON PAGE 52!
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 9: Hydraulics
Hydraulic System Diagram
X
W ꢁ>ch^YZꢀ8dcigdaꢀ7dmꢂꢀ
W
HVlꢀ7dl
8na^cYZg
X
V ꢁ>ch^YZꢀK^hZꢂ
JhZg
9dlc[ZZY
(figure 82*)
6Y_jhiꢀ@cdW
(ꢀfigure 80*)
V
K^hZꢀ8aVbe
K^hZ
8na^cYZg
(figure 81*)
Y
ꢁ>ch^YZꢀHiVcYꢂ
*see figures
on page 58
KVakZꢀBVc^[daYꢀ
ꢁcdc"hZgk^XZVWaZꢂ
(figure 79*)
G:6GꢀD;ꢀ
B6C>;DA9
ꢁEdh^i^dcꢀd[ꢀ[^ii^c\h
bdY^[^ZYꢀ[dgꢀXaVg^inꢂ
;^mZYꢀ9dlc[ZZY
6Y_jhiꢀ@cdWꢀ
K^hZꢀ8aVbe^c\
EgZhhjgZꢀKVakZ
(figure 79*)
K^hZ
HdaZcd^Y
(figure 78*)
(%`\$Xbꢃ
)',ꢀEH>ꢀ
EgZhhjgZ
<Vj\ZꢀꢁDcꢀIdeꢀd[ꢀBVc^[daYꢂ
(figure 79*)
K^hZ
8adhZ
K^hZ
DeZc
&¿'ꢀ=Eꢀ=nYgVja^XꢀEjbeꢀ
Bdidgꢀ(ꢀꢀfꢀꢀiꢀgꢀꢀuꢀꢀꢀrꢀeꢀꢀꢀꢀ7ꢀꢀ7ꢀꢀ*)
HVlꢀ7dl
HdaZcd^Yꢀ
(figure 78*)
7dl
7dl
GV^hZ
AdlZg
WARNING!
POISON HAZARD!
Fluid leaks may be
at extremely high
pressure. Hydraulic
Fluid injected into
the body is a medical
emergency.
B
Y
I]^hꢀXdbedcZciꢀVahdꢀ]Vhꢀ
ZaZXig^XVaꢀXdccZXi^dch#ꢀ
HZZꢀWiringꢀdcꢀPage ??.?
=nYgVja^Xꢀ;aj^YꢀIVc`
(figure 77*)
-57-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Hydraulic Components
figure 77. Hydraulic fluid tank.
figure 80. Downfeed adjust knob.
figure 78. Solenoids.
figure 81. Vise cylinder.
figure 79. Manifold overhead view.
figure 82. Saw bow cylinder.
-58-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10: pARTS
Main parts Breakdown
-59-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
60
61
62
63
64
65
66
67
68
69
P0664060
P0664061
P0664062
P0664063
PLW04M
PSB31M
P0664066
PRP58M
PSS09M
P0664069
DRIVE WHEEL FRAME
IDLER WHEEL FRAME
ANCHOR BLOCK
104-1 P0664104-1
104-2 P0664104-2
104-3 PB29M
BRUSH SUPPORT
BRUSH
HEX BOLT M6-1 X 30
FLAT WASHER 6MM
HEX NUT M6-1
GIB
104-4 PW03M
104-5 PN01M
104-6 PW02M
104-7 PS05M
LOCK WASHER 8MM
CAP SCREW M8-1.25 X 25
BLADE TENSION BAR
ROLL PIN 6 X 45
FLAT WASHER 5MM
PHLP HD SCR M5-.8 X 8
BLADE ADJUST STICK
KNOB M6-1 X 15
105
106
107
108
109
110
114
115
116
117
118
120
121
125
126
127
128
129
130
131
132
133
134
135
137
138
139
140
141
142
P0664105
P0664106
P0664107
PW06M
SET SCREW M8-1.25 X 20
LIMIT SWITCH
FIX BLOCK
69-1 P0664069-1
69-2 PW02M
69-3 PS05M
69-4 PS51M
SWITCH BRACKET
FLAT WASHER 5MM
PHLP HD SCR M5-.8 X 8
PHLP HD SCR M4-.7 X 30
MAIN PIVOT SHAFT
EXT RETAINING RING 45MM
BEARING SPACER
FLAT WASHER 12MM
HANDLE
P0664109
PSB13M
CAP SCREW M8-1.25 X 30
BALL BEARING 51203
SPECIAL WASHER
BLADE TENSION WHEEL
BLADE TENSION HANDLE
BLADE TENSION SCALE
CONNECTING TUBE
HANDLE CAP
P0664114
P0664115
P0664116
P0664117
P0664118
P0664120
P0664121
P0664125
P0664126
P0664127
P0664128
P0664129
P0664130
P0664131
P0664132
P0664133
P0664134
P0664135
PRP08M
70
71
72
73
74
75
76
77
80
81
82
83
84
85
86
P0664070
PR56M
P0664072
PORG070
P0664074
P0664075
P0664076
P0664077
P0664080
PSB36M
PSB13M
PSS64M
P0664084
PSB63M
P0664086
O-RING 69.4 X 3.1 G70
BALL BEARING 32009J
MAIN PIVOT SPACER
DUST SHIELD
IDLER WHEEL
SPECIAL NUT M45-1.5
BLADE GUIDE BLOCK
CAP SCREW M12-1.75 X 25
CAP SCREW M8-1.25 X 30
SET SCREW M6-1 X 15
RELEASE BLOCK
IDLER WHEEL SHAFT
DUST COVER
BALL BEARING 32007J
SPECIAL NUT M35-1.5
DRIVE WHEEL
DRIVE GEAR SHAFT
DRIVE GEAR KEY
SHAFT BUSHING
CAP SCREW M12-1.75 X 60
BLADE GUARD REAR
BUTTON HD CAP SCR M5-.8 X 12
FLAT WASHER 6MM
CAP SCREW M6-1 X 15
UPPER STOP BRACKET
STOP KNOB
86-1 P0664086-1
87 PW03M
87-1 PSB28M
89 P0664089
BALL BEARING 6307ZZ
BLADE 4/6T VP HSS
ROLL PIN 6 X 30
PLW05M
PSB131M
P0664140
PS11M
LOCK WASHER 12MM
CAP SCREW M12-1.75 X 45
BLADE COVER
89-1 P0664089-1
89-2 P0664089-2
89-3 PB29M
STOP BLOCK
HEX BOLT M6-1 X 30
FLAT WASHER 6MM
BLADE GUIDE UPPER
BLADE GUIDE LOWER
HOSE VALVE
PHLP HD SCR M6-1 X 16
BLADE COVER LATCH
HOOK
89-4 PW03M
P0664142
90
91
92
93
94
95
96
97
98
99
100
P0664090
P0664091
P0664092
P0664093
P0664094
P0664095
PSB11M
PSB28M
PW03M
142-1 P0664142-1
143
160
161
162
163
164
165
PS19M
PHLP HD SCR M5-.8 X 6
SPRING BRACKET
CAP SCREW M10-1.5 X 35
SPRING BRACKET
CAP SCREW M8-1.25 X 25
RAM ASSEMBLY
P0664160
PSB84M
P0664162
PSB31M
P0664164
P0664165
BLADE GUIDE BACK
BLADE GUIDE LEFT
BLADE GUIDE RIGHT
CAP SCREW M8-1.25 X 16
CAP SCREW M6-1 X 15
FLAT WASHER 6MM
CAP SCREW M6-1 X 15
BLADE GUARD
EXTENSION SPRING
BUSHING
165-1 P0664165-1
PSB28M
P0664100
166
167
168
170
171
172
200
P0664166
P0664167
P0664168
P0664170
PW01M
BEARING
SPRING TENSION LEADSCREW
SPRING TENSION KNOB
RAM PIN
102-1 P0664102-1
102-2 P0664102-2
102-3 PW02M
102-4 PS05M
BRACKET
LASER LIGHT
FLAT WASHER 5MM
PHLP HD SCR M5-.8 X 8
PHLP HD SCR M5-.8 X 8
FLAT WASHER 8MM
CAP SCREW M8-1.25 X 15
GEAR BOX
PSB100M
P0664200
102-5 PS05M
-60-
G0664 Heavy Duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Main parts List (Continued)
REF PART #
201 P0664201
DESCRIPTION
MOTOR 2.5 HP 220V 3-PH
SAW MOTOR FAN
REF PART #
DESCRIPTION
MICRO CONTROL BLOCK
HOSE CLAMP
248-3 P0664248-3
248-4 P0664248-4
248-5 P0664248-5
248-6 P0664248-6
248-7 P0664248-7
248-8 PSB07M
201-1 P0664201-1
201-2 P0664201-2
201-3 P0664201-3
SAW MOTOR FAN COVER
SAW MOTOR JUNCTION BOX
KEY 8 X 7 X 40
NET TUBE
3 WAY VALVE
202
204
205
206
207
208
209
210
211
P0664202
PLW04M
PSB31M
PW04M
HOSE FITTING
LOCK WASHER 8MM
CAP SCREW M6-1 X 30
PU TUBE SHORT
CAP SCREW M8-1.25 X 25
FLAT WASHER 10MM
CAP SCREW M10-1.5 X 25
DRIVE SHAFT WASHER
CAP SCREW M10-1.5 X 20
REDUCER COVER
248-9 P0664248-9
248-10 P0664248-10 PU TUBE LONG
PSB64M
P0664208
PSB61M
P0664210
PSB100M
250-1 P0664250-1
250-2 PLW03M
250-3 PSB28M
250-4 PS51M
POWER CUTTING BRACKET
LOCK WASHER 6MM
CAP SCREW M6-1 X 15
PHLP HD SCR M4-.7 X 30
CAP SCREW M8-1.25 X 15
Roller Stand parts Breakdown & List
506
505
507
508
510
509
501
508
509
502
511
510
512
511
512
513
503
514
515
516
504
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
501
502
503
504
505
506
507
508
G0664501
G0664502
G0664503
G0664504
G0664505
G0664506
P6003
TABLE RAIL
509
510
511
512
513
514
515
516
PN09M
HEX NUT M12-1.75
HEX BOLT M8-1.25 X 16
FLAT WASHER 8MM
HEX NUT M8-1.25
LEG ASSEMBLY
LOWER LEG
PB03M
PW01M
PN03M
ADJUSTABLE FOOT
ROLLER SHAFT
ROLLER
PSB11M
PN13M
CAP SCREW M8-1.25 X 16
HEX NUT M16-2
BALL BEARING 6003ZZ
FLAT WASHER 12MM
G0664515
PSS03M
FOOT STUD
PW06M
SET SCREW M6-1 X 8
-61-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Base parts Breakdown
-62-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Base Breakdown
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
P0664001
P0664002
P0664003
P0664004
P0664005
P0664006
P0664007
P0664008
P0664009
P0664010
PSB36M
SAW SWIVEL BASE
VISE BACK PLATE RIGHT
VISE BACK PLATE LEFT
VISE JAW RIGHT
36
37
38
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
P0664036
P0664037
PSS06M
P0664040
P0664041
PFH11M
PSS25M
P0664044
PW08M
HANDLE SHAFT
2
HANDLE
3
SET SCREW M8-1.25 X 16
VISE JAW BRACKET FRONT
VISE PLATE
4
5
VISE JAW LEFT
6
SAW SWIVEL
FLAT HD SCR M8-1.25 X 15
SET SCREW M6-1 X 20
LEADSCREW
7
SPECIAL NUT M30-1.5
SHAFT
8
9
BALL BEARING 35 X 52 X 4
SPECIAL NUT M35-1.5
CAP SCREW M12-1.75 X 25
SET SCREW M12-1.75 X 20
SET SCREW M6-1 X 10
WORK STOP ROD
LOCK KNOB
FLAT WASHER 16MM
HANDWHEEL
10
11
12
P0664046
PRP05M
P0664048
PW01M
ROLL PIN 5 X 30
PSS77M
CYLINDER
13-2 PSS01M
13-3 P0664013-3
13-4 P0664013-4
13-5 PLW03M
13-6 P0664013-6
13-7 P0664013-7
13-8 PN02M
FLAT WASHER 8MM
CAP SCREW M8-1.25 X 30
SET SCREW M8-1.25 X 16
ACCESSORY BRACKET
FLAT WASHER 10MM
CAP SCREW M10-1.5 X 30
HEX NUT M12-1.75
CAP SCREW M12-1.75 X 50
CONTROL BOX ASSEMBLY
CONTROL PANEL LABEL
FEED SPEED LABEL
FLAT WASHER 8MM
CAP SCREW M8-1.25 X 25
BRACKET
PSB13M
PSS06M
P0664052
PW04M
LOCK WASHER 6MM
WORK STOP BRACKET
WORK STOP
PSB72M
PN09M
HEX NUT M10-1.5
13-9 PB32M
HEX BOLT M10-1.5 X 25
PIVOT BEARING COVER
CAP SCREW M6-1 X 15
STAND
PSB73M
P0664057
14
P0664014
14-1 PSB28M
15-1 P0664015-1
15-2 P0664015-2
15-3 P0664015-3
16-1 P0664016-1
16-2 P0664016-2
16-3 P0664016-3
16-4 P0664016-4
17-1 PB09M
57-1 P0664057-1
57-2 P0664057-2
FLUID COLLECT PLATE
COOLANT CATCH TRAY
STAND LEG RIGHT
STAND LEG LEFT
58
59
78
PW01M
PSB31M
P0664078
78-1 PSB28M
78-2 PS51M
78-3 PW03M
CAP SCREW M6-1 X 15
PHLP HD SCR M4-.7 X 30
FLAT WASHER 6MM
COOLING PUMP ASSEMBLY
LOCK WASHER 6MM
CAP SCREW M6-1 X 15
MACHINE FLUID HOSE
HOSE CLAMP
STAND MIDDLE PANEL
STAND FRONT PANEL
HEX BOLT M8-1.25 X 20
FLAT WASHER 8MM
HEX NUT M8-1.25
240
241
242
P0664240
PLW03M
PSB28M
17-2 PW01M
17-3 PN03M
17-4 PN13M
HEX NUT M16-2
245-1 P0664245-1
245-2 P0664245-2
245-3 P0664245-3
245-4 P0664245-4
245-5 P0664245-5
245-6 P0664245-6
245-7 P0664245-7
245-8 P0664245-8
17-5 PSB122M
18-1 PSB14M
18-2 PW01M
CAP SCREW M16-2 X 50
CAP SCREW M8-1.25 X 20
FLAT WASHER 8MM
HEX NUT M8-1.25
SPRAYER FLUID HOSE
SPRAYER
18-3 PN03M
ELBOW
19-1 PW03M
FLAT WASHER 6MM
CAP SCREW M6-1 X 15
SET SCREW M10-1.5 X 40
FLAT WASHER 10MM
HEX NUT M10-1.5
MANIFOLD
19-2 PSB28M
19-3 P0664019-3
19-4 PW04M
CONNECTOR
HOSE CLAMP
246
350
P0664246
P0664350
GREASE FITTING
19-5 PN02M
HYDRAULIC UNIT
21
22
30
31
32
33
34
35
P0664021
P0664022
P0664030
P0664031
P0664032
P0664033
P0664034
P0664035
PIVOT LOCK SHAFT
PIVOT LOCK HANDLE
VISE TABLE
350-1 P0664350-1
350-2 P0664350-2
350-3 P0664350-3
350-4 P0664350-4
350-5 P0664350-5
HYDRAULIC VALVE SET
MOTOR 1/2 HP 220V 3-PH
PUMP MOTOR FAN
PUMP MOTOR FAN COVER
PUMP MOTOR JUNCTION BOX
HOSE W/TUBE FITTING
HOSE W/TUBE FITTING
HEX BOLT M6-1 X 20
COMPRESSION SPRING
RACK SHAFT
GEAR SHAFT
351
352
353
P0664351
P0664352
P0664353
SHAFT BUSHING
HANDLE
-63-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
Labels Breakdown and List
405
404
406
403
402
407
401
410
409
408
REF PART #
DESCRIPTION
MACHINE ID LABEL
REF PART #
DESCRIPTION
ELECTRICITY LABEL
401
402
403
404
405
P0664401
P0664402
P0664403
P0664404
PLABEL-12A
406
PLABEL-14
PPAINT-11
PPAINT-1
G8589
WEAR SAFETY GLASSES LABEL
MODEL NUMBER LABEL
DISCONNECT LABEL
407
408
409
410
GRIZZLY PUTTY TOUCH UP PAINT
GRIZZLY GREEN TOUCH UP PAINT
GRIZZLY NAMEPLATE-LARGE
BLADE DANGER LABEL
READ MANUAL LABEL
P0664410
Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine
MUST maintain the original location and readability of the labels on the machine. If any label is
removed or becomes unreadable, REpLACE that label before using the machine again. Contact
-64-
g0664 heavy duty Metal-Cutting Bandsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
7!22!.49 #!2$
CVbZꢀTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTT ꢀ
HigZZiꢀTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTT
8^inꢀ TTTTTTTTTTTTTTTTTTTTTTT HiViZꢀTTTTTTTTTTTTTTTTTTTTTTTTT O^eꢀ TTTTTTTTTTTTTTTTTTTTT
E]dcZꢀꢁꢀTTTTTTTTTTTTTTTTTTTT :bV^aꢀ TTTTTTTTTTTTTTTTTTTTTTTT >ckd^XZꢀꢁꢀTTTTTTTTTTTTTTTTT
BdYZaꢀꢁꢀTTTTTTTTTTTTTTTTTTTT DgYZgꢀꢁꢀTTTTTTTTTTTTTTTTTTTTTTT HZg^VaꢀꢁꢀTTTTTTTTTTTTTTTTTT
4HE FOLLOWING INFORMATION IS GIVEN ON A VOLUNTARY BASISꢀ )T WILL BE USED FOR MARKETING PURPOSES TO HELP US DEVELOP
BETTER PRODUCTS AND SERVICESꢀ /F COURSEꢀ ALL INFORMATION IS STRICTLY CONFIDENTIALꢁ
ꢀꢁꢀ =dlꢀY^YꢀndjꢀaZVgcꢀVWdjiꢀjh4
ꢀ
ꢀTTTT 6YkZgi^hZbZciꢀ
ꢀ TTTT ;g^ZcYꢀ
ꢀ TTTT LZWh^iZꢀ
ꢀTTTT 8ViVad\
ꢀTTTT Di]Zg/
ꢀ
ꢀTTTT 8VgYꢀ9ZX`ꢀ
ꢂꢁꢀ L]^X]ꢀd[ꢀi]Zꢀ[daadl^c\ꢀbV\Vo^cZhꢀYdꢀndjꢀhjWhXg^WZꢀid4
TTTT 8VW^cZiꢀBV`Zg
TTTT ;Vb^anꢀ=VcYnbVc
TTTT =VcYꢀAdVYZg
TTTT EdejaVgꢀBZX]Vc^Xh
TTTT EdejaVgꢀHX^ZcXZ
TTTT EdejaVgꢀLddYldg`^c\
TTTT EgVXi^XVaꢀ=dbZdlcZg
TTTT EgZX^h^dcꢀH]ddiZg
TTTT Egd_ZXihꢀ^cꢀBZiVa
TTTT G8ꢀBdYZaZg
TTTT IdYVn»hꢀ=dbZdlcZg
TTTT LddY
TTTT LddYZcꢀ7dVi
TTTT LddYh]deꢀCZlh
TTTT LddYhb^i]
TTTT =VcYn
TTTT =dbZꢀH]deꢀBVX]^c^hi
TTTT ?djgcVaꢀd[ꢀA^\]iꢀ8dci#
TTTT A^kZꢀHiZVb
TTTT BdYZaꢀ6^geaVcZꢀCZlh
TTTT BdYZaiZX
TTTT LddYldg`
TTTT LddYldg`ZgꢀLZhi
TTTT LddYldg`Zg»hꢀ?djgcVa
TTTT Di]Zg/
TTTT G^ÄZ
TTTT H]deꢀCdiZh
TTTT DaYꢀ=djhZꢀ?djgcVa
TTTT H]di\jcꢀCZlh
ꢃꢁꢀ L]Viꢀ^hꢀndjgꢀVccjVaꢀ]djhZ]daYꢀ^cXdbZ4
ꢀ
ꢀTTTT ꢂ'%!%%%"ꢂ'.!%%%ꢀ
ꢀ TTTT ꢂ(%!%%%"ꢂ(.!%%%ꢀ
ꢀTTTT ꢂ)%!%%%"ꢂ).!%%%
ꢀTTTT ꢂ,%!%%%
ꢀ
ꢀTTTT ꢂ*%!%%%"ꢂ*.!%%%ꢀ
ꢀ TTTT ꢂ+%!%%%"ꢂ+.!%%%ꢀ
ꢄꢁꢀ L]Viꢀ^hꢀndjgꢀV\Zꢀ\gdje4
ꢀ
ꢀTTTT '%"'.ꢀ
ꢀ TTTT (%"(.ꢀ
ꢀ TTTT +%"+.ꢀ
ꢀTTTT )%").
ꢀTTTT ,%
ꢀ
ꢀTTTT *%"*.ꢀ
ꢅꢁꢀ =dlꢀadc\ꢀ]VkZꢀndjꢀWZZcꢀVꢀlddYldg`Zg$bZiValdg`Zg4
ꢀTTTT %"'ꢀNZVghꢀ ꢀTTTT '"-ꢀNZVghꢀ ꢀTTTT -"'%ꢀNZVghꢀꢀ
ꢀ
ꢀ TTTT'% ꢀNZVgh
ꢆꢁꢀ =dlꢀbVcnꢀd[ꢀndjgꢀbVX]^cZhꢀdgꢀiddahꢀVgZꢀ<g^ooan4
ꢀTTTT %"'ꢀ ꢀTTTT ("*ꢀ
ꢀ
ꢀTTTT +".ꢀ
ꢀ TTTT&%
ꢀTTTTTCd
ꢀTTTTTCd
ꢇꢁꢀ 9dꢀndjꢀi]^c`ꢀndjgꢀbVX]^cZꢀgZegZhZcihꢀVꢀ\ddYꢀkVajZ4ꢀ
ꢈꢁꢀ LdjaYꢀndjꢀgZXdbbZcYꢀ<g^ooanꢀ>cYjhig^VaꢀidꢀVꢀ[g^ZcY4ꢀ
ꢀTTTTTNZhꢀ
ꢀTTTTTNZhꢀ
ꢉꢁꢀ LdjaYꢀndjꢀVaadlꢀjhꢀidꢀjhZꢀndjgꢀcVbZꢀVhꢀVꢀgZ[ZgZcXZꢀ[dgꢀ<g^ooanꢀXjhidbZghꢀ^cꢀndjgꢀVgZV4
.OTEꢊ 7E NEVER USE NAMES MORE THAN ꢁ TIMESꢀꢀ ꢀTTTTTNZhꢀ ꢀTTTTTCd
ꢀ
ꢀꢋꢁꢀ 8dbbZcih/ ?????????????????????????????????????????????????????????????????????
?????????????????????????????????????????????????????????????????????????????????
?????????????????????????????????????????????????????????????????????????????????
?????????????????????????????????????????????????????????????????????????????????
Download from Www.Somanuals.com. All Manuals Search And Download.
;DA9ꢀ6ADC<ꢀ9DII:9ꢀA>C:
EaVXZ
HiVbe
=ZgZ
'2)::,9 ).$5342)!,ꢀ ).#ꢁ
0ꢁ/ꢁ "/8 ꢂꢃꢄꢅ
"%,,).'(!-ꢀ 7! ꢅꢆꢂꢂꢇꢈꢂꢃꢄꢅ
;DA9ꢀ6ADC<ꢀ9DII:9ꢀA>C:
HZcYꢀVꢀ<g^ooanꢀ8ViVad\ꢀidꢀVꢀ[g^ZcY/
CVbZTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTT
HigZZiTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTT
8^inTTTTTTTTTTTTTTHiViZTTTTTTO^eTTTTTT
I6E:ꢀ6ADC<ꢀ:9<:H""EA:6H:ꢀ9DꢀCDIꢀHI6EA:
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
7!22!.49 !.$ 2%452.3
<g^ooanꢀ>cYjhig^Va!ꢀ>cX#ꢀlVggVcihꢀZkZgnꢀegdYjXiꢀ^iꢀhZaahꢀ[dgꢀVꢀeZg^dYꢀd[ꢀꢀ YEARꢀidꢀi]Zꢀdg^\^cVaꢀejgX]VhZgꢀ[gdbꢀ
i]ZꢀYViZꢀd[ꢀejgX]VhZ#ꢀI]^hꢀlVggVcinꢀYdZhꢀcdiꢀVeeanꢀidꢀYZ[ZXihꢀYjZꢀY^gZXianꢀdgꢀ^cY^gZXianꢀidꢀb^hjhZ!ꢀVWjhZ!ꢀ
cZ\a^\ZcXZ!ꢀVXX^YZcih!ꢀgZeV^ghꢀdgꢀVaiZgVi^dchꢀdgꢀaVX`ꢀd[ꢀbV^ciZcVcXZ#ꢀI]^hꢀ^hꢀ<g^ooan»hꢀhdaZꢀlg^iiZcꢀlVggVcinꢀ
VcYꢀVcnꢀVcYꢀVaaꢀlVggVci^Zhꢀi]ViꢀbVnꢀWZꢀ^bea^ZYꢀWnꢀaVl!ꢀ^cXajY^c\ꢀVcnꢀbZgX]VciVW^a^inꢀdgꢀ[^icZhh!ꢀ[dgꢀVcnꢀeVg"
i^XjaVgꢀejgedhZ!ꢀVgZꢀ]ZgZWnꢀa^b^iZYꢀidꢀi]ZꢀYjgVi^dcꢀd[ꢀi]^hꢀlg^iiZcꢀlVggVcin#ꢀLZꢀYdꢀcdiꢀlVggVciꢀdgꢀgZegZhZciꢀ
i]Viꢀi]ZꢀbZgX]VcY^hZꢀXdbea^Zhꢀl^i]ꢀi]Zꢀegdk^h^dchꢀd[ꢀVcnꢀaVlꢀdgꢀVXihꢀjcaZhhꢀi]ZꢀbVcj[VXijgZgꢀhdꢀlVggVcih#ꢀ
>cꢀcdꢀZkZciꢀh]Vaaꢀ<g^ooan»hꢀa^VW^a^inꢀjcYZgꢀi]^hꢀlVggVcinꢀZmXZZYꢀi]ZꢀejgX]VhZꢀeg^XZꢀeV^Yꢀ[dgꢀi]ZꢀegdYjXiꢀVcYꢀ
VcnꢀaZ\VaꢀVXi^dchꢀWgdj\]iꢀV\V^chiꢀ<g^ooanꢀh]VaaꢀWZꢀig^ZYꢀ^cꢀi]ZꢀHiViZꢀd[ꢀLVh]^c\idc!ꢀ8djcinꢀd[ꢀL]ViXdb#
LZꢀh]Vaaꢀ^cꢀcdꢀZkZciꢀWZꢀa^VWaZꢀ[dgꢀYZVi]!ꢀ^c_jg^ZhꢀidꢀeZghdchꢀdgꢀegdeZginꢀdgꢀ[dgꢀ^cX^YZciVa!ꢀXdci^c\Zci!ꢀheZX^Va!ꢀ
dgꢀXdchZfjZci^VaꢀYVbV\ZhꢀVg^h^c\ꢀ[gdbꢀi]ZꢀjhZꢀd[ꢀdjgꢀegdYjXih#
IdꢀiV`ZꢀVYkVciV\Zꢀd[ꢀi]^hꢀlVggVcin!ꢀXdciVXiꢀjhꢀWnꢀbV^aꢀdgꢀe]dcZꢀVcYꢀ\^kZꢀjhꢀVaaꢀi]ZꢀYZiV^ah#ꢀLZꢀl^aaꢀi]Zcꢀ
^hhjZꢀndjꢀVꢀ¸GZijgcꢀCjbWZg!»»ꢀl]^X]ꢀbjhiꢀWZꢀXaZVganꢀedhiZYꢀdcꢀi]Zꢀdjih^YZꢀVhꢀlZaaꢀVhꢀi]Zꢀ^ch^YZꢀd[ꢀi]Zꢀ
XVgidc#ꢀLZꢀl^aaꢀcdiꢀVXXZeiꢀVcnꢀ^iZbꢀWVX`ꢀl^i]djiꢀi]^hꢀcjbWZg#ꢀEgdd[ꢀd[ꢀejgX]VhZꢀbjhiꢀVXXdbeVcnꢀi]Zꢀ
bZgX]VcY^hZ#ꢀ
I]ZꢀbVcj[VXijgZghꢀgZhZgkZꢀi]Zꢀg^\]iꢀidꢀX]Vc\ZꢀheZX^[^XVi^dchꢀViꢀVcnꢀi^bZꢀWZXVjhZꢀi]ZnꢀXdchiVcianꢀhig^kZꢀidꢀ
VX]^ZkZꢀWZiiZgꢀfjVa^inꢀZfj^ebZci#ꢀLZꢀbV`ZꢀZkZgnꢀZ[[dgiꢀidꢀZchjgZꢀi]ViꢀdjgꢀegdYjXihꢀbZZiꢀ]^\]ꢀfjVa^inꢀVcYꢀ
YjgVW^a^inꢀhiVcYVgYhꢀVcYꢀlZꢀ]deZꢀndjꢀcZkZgꢀcZZYꢀidꢀjhZꢀi]^hꢀlVggVcin#
EaZVhZꢀ[ZZaꢀ[gZZꢀidꢀlg^iZꢀdgꢀXVaaꢀjhꢀ^[ꢀndjꢀ]VkZꢀVcnꢀfjZhi^dchꢀVWdjiꢀi]ZꢀbVX]^cZꢀdgꢀi]ZꢀbVcjVa#ꢀ
I]Vc`ꢀndjꢀV\V^cꢀ[dgꢀndjgꢀWjh^cZhhꢀVcYꢀXdci^cjZYꢀhjeedgi#ꢀLZꢀ]deZꢀidꢀhZgkZꢀndjꢀV\V^cꢀhddc#
Download from Www.Somanuals.com. All Manuals Search And Download.
"UY $IRECT AND 3AVE WITH 'RIZZLY® n 4RUSTEDꢀ 0ROVEN AND A 'REAT 6ALUEꢁ
6ISIT /UR 7EBSITE 4ODAY !ND $ISCOVER
7HY 'RIZZLY® )S 4HE )NDUSTRY ,EADERꢀ
s 3%#52% /2$%2).'
s /2$%23 3()00%$ 7)4(). ꢃꢄ (/523
s %ꢂ-!), 2%30/.3% 7)4(). /.% (/52
ꢂ/2ꢂ
#ALL 4ODAY &OR !
&2%%
&ULL #OLOR #ATALOG
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Graco Crib 9415 User Manual
Graco Electric Heater 309524L User Manual
Grizzly Nail Gun G6045 User Manual
Honeywell Marine Instruments KMA 29 User Manual
Honeywell Video Gaming Accessories TrueSTEAM User Manual
Hotpoint Refrigerator FF200DP User Manual
Hotpoint Washer WmAQL 721 User Manual
HP Hewlett Packard Network Cables 8505A User Manual
HTC PDAs Smartphones PDA Phone User Manual
Huey Chiao Bluetooth Headset HCB38 User Manual