18 GAUGE BRAD NAILER
MODEL G6045/G6046/G6047
INSTRUCTION MANUAL
Model G6047
Model G6046
Nailer With Case
Model G6045 not shown
COPYRIGHT © OCTOBER, 2001 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN TAIWAN
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions For Power Tools
10. USE PROPER EXTENSION CORD
15. MAINTAIN TOOLS WITH CARE.
Keep tools sharp and clean for best
and safest performance. Follow
instructions for lubricating and
changing accessories.
for the tool. Make sure your extension
cord is in good condition. Conductor
size should be in accordance with the
chart below. The amperage rating
should be listed on the motor or tool
nameplate. An undersized cord will
cause a drop in line voltage resulting
in loss of power and overheating.
Your extension cord must also con-
tain a ground wire and plug pin.
Always repair or replace extension
cords if they become damaged.
16. DISCONNECT TOOLS before ser-
vicing and changing accessories.
17. REDUCE THE RISK OF UNINTEN-
TIONAL STARTING. Make sure
switch is in off position before plug-
ging in.
18. USE
THE
RECOMMENDED
Consult the
ACCESSORIES.
owner’s manual for recommended
accessories. The use of improper
accessories may cause risk of injury.
Minimum Gauge for Extension Cords
AMP
RATING
0-6
LENGTH
50ft
16
25ft
18
18
16
14
12
10
100ft
16
14
14
12
19. CHECK DAMAGED PARTS. Before
further use of the tool, a guard or
other part that is damaged should be
carefully checked to determine that it
will operate properly and perform its
intended function. Check for align-
ment of moving parts, binding of
moving parts, breakage of parts,
mounting, and any other conditions
that may affect its operation. A guard
or other part that is damaged should
be properly repaired or replaced.
7-10
16
16
12
12
11-12
13-16
17-20
21-30
10
No
10
11. WEAR PROPER APPAREL. Do not
wear loose clothing, gloves, neckties,
rings, bracelets, or other jewelry
which may get caught in moving
parts. Non-slip footwear is recom-
mended. Wear protective hair cover-
ing to contain long hair.
20. NEVER LEAVE TOOL RUNNING
UNATTENDED. Turn the power off,
and do not leave tool until it comes to
a complete stop.
12. ALWAYS USE SAFETY GLASSES.
Also use face or dust mask if cutting
operation is dusty. Everyday eye-
glasses only have impact resistant
lenses, they are NOT safety glasses.
21. NEVER ALLOW UNTRAINED
USERS TO RUN THIS TOOL
WHILE UNSUPERVISED.
13. SECURE WORK. Use clamps or a
vise to hold work when practical. it is
safer than using your hand and frees
both hands to operate tool.
22. IF YOU ARE UNSURE OF THE
INTENDED OPERATION, STOP
USING THE TOOL. Seek formal
training or research books or maga-
zines that specialize in power tools.
14. DO NOT OVERREACH. Keep proper
footing and balance at all times.
-2-
G6045/G6046/G6047 18 Gauge Brad Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Nailer Safety
In addition to the rules stated in the previ-
ous section, and those in the warning
boxes throughout this manual, please
observe the following safety tips for your
new nailer:
1. READ THIS ENTIRE MANUAL
BEFORE OPERATING THE NAIL-
ER.
2. ALWAYS DISCONNECT AIR FROM
THE NAILER WHENEVER SERVIC-
ING OR INSTALLING NAILS. During
maintenance, a nailer connected to
air may fire accidentally, causing seri-
ous personal injury.
3. DO NOT PLACE HANDS NEAR
NAIL POINT OF ENTRY. Nail can
deflect and tear through the surface
of the workpiece, puncturing your
hand or fingers.
Operating this nailer can propel
objects into the air, causing immedi-
ate eye damage. To protect yourself,
always wear American National
Standards Institute (ANSI) approved
safety glasses or goggles when oper-
ating this equipment. In addition, this
nailer discharges at 85-90 decibels.
To protect your hearing, always wear
ANSI approved ear protection when
operating this nailer.
4. NEVER CONNECT THE NAILER TO
PRESSURIZED
OXYGEN
OR
OTHER COMBUSTIBLE GASES AS
A POWER SOURCE. Only use fil-
tered, lubricated, and regulated com-
pressed air.
5. NEVER USE GASOLINE OR
OTHER FLAMMABLE LIQUIDS TO
CLEAN THE NAILER. Vapors in the
tool will ignite by a spark and cause
the tool to explode.
6. DO NOT CARRY THE NAILER BY
ANY OTHER PART THAN THE
HANDLE, and do not carry the nailer
by the air hose.
7. DO NOT KEEP THE TRIGGER
PULLED ON THE SAFETY YOKE
MECHANISM WHEN CARRYING
OR HOLDING THE TOOL.
Never point this nailer at yourself or
another person! Always pay attention
to the direction this nailer is pointed.
Use this tool with respect and caution
to lessen the possibility of operator or
bystander injury. Ignoring this warn-
ing may result in serious personal
injury.
8. DO NOT USE A CHECK VALVE OR
ANY OTHER FITTING THAT
ALLOWS AIR TO REMAIN IN THE
TOOL.
-3-
G6045/G6046/G6047 18 Gauge Brad Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Most importantly, we stand behind our
Commentary
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
We are proud to offer the Grizzly Model
G6045/G6046/G6047 18 Gauge Brad
Nailer. This model is part of a growing
Grizzly family of fine power tools. When
used according to the guidelines set forth
in this manual, you can expect years of
trouble-free, enjoyable operation and
proof of Grizzly’s commitment to customer
satisfaction.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Pennsdale, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
This model features 360˚ adjustable
exhaust, a convenient side-loading maga-
zine, a safety trigger and a durable plastic
carrying case.
We are pleased to provide this manual
with the Model G6045/G6046/G6047. It
was written to encourage safety consider-
ations and guide you through general
operating procedures and maintenance.
This manual represents our effort to pro-
duce the best documentation possible.
The specifications, details, and pho-
tographs in this manual represent the
Model G6045/G6046/G6047 as supplied
when the manual was prepared. However,
owing to Grizzly’s policy of continuous
improvement, changes may be made at
any time with no obligation on the part of
Grizzly. If you have any comments regard-
ing this manual, please write to us at the
address below:
Read the manual before assembly
and operation. Become familiar with
this tool, its safety instructions, and
its operation before beginning any
work. Serious personal injury may
result if safety or operational infor-
mation is not understood or followed.
Grizzly Industrial, Inc.
Technical Documentation
P.O. Box 2069
C
/O
Bellingham, WA 98227-2069
-4-
G6045/G6046/G6047 18 Gauge Brad Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
Compressed Air System
Safety Yoke Mechanism
The Models G6045 & G6046 are designed
to be operated at 60-100 psi. The Model
G6047 is designed to be operated at 70-
110 psi. Do not exceed the maximum
operating pressure for your model.
A safety yoke mechanism (bump fire) on
the nose of the nailer acts as a secondary
safety device. When the trigger is pressed,
the nailer will not fire until the safety yoke
mechanism is depressed.
Before using your new nailer, install the
included ⁄8" quick connect fitting. Install a
female 3⁄8" fitting on the air hose. Regulate
the air pressure on your air compressor to
barely over the minimum psi for your
model.
Before you use your nailer for the first time,
check the safety yoke mechanism to
ensure proper function. To do this:
3
1. Make sure the nailer is disconnect-
ed from the air supply!
2. Make sure the magazine is empty and
contains no nails.
3. Make sure the trigger and the safety
yoke mechanism move up and down
without sticking.
4. Connect the nailer to the air supply.
5. Without pressing the trigger,
depress the safety yoke mechanism
against a scrap piece of wood that is
clean and free of any knots, nails, or
other foreign objects. If the nailer
does not fire, then the safety yoke
mechanism is working correctly. If the
nailer does fire when you do this,
immediately disconnect the nailer
from the air supply and call our cus-
tomer service for help.
Many pneumatic tools benefit from an in-
line filter/lubricator/regulator unit. This
attachment is connected by hoses
between the air compressor and the nailer.
Using this unit protects your tool from dam-
aging water build-up, allows you to adjust
and maintain constant air pressure to your
tool, and saves you the inconvenience of
having to manually lubricate your tool
every time you use it. Check the current
Grizzly catalog for availability of this unit. If
you plan on installing a filter/lubricator/reg-
ulator unit in your compressed air system,
always follow the connection instructions
that come with the unit.
Similarly if the nailer fires when the trigger
is pulled, without the safety yoke mecha-
nism being depressed, then the nailer is
not working properly.
If either of these two conditions develop
after you have used your nailer for a peri-
od of time, check the lubrication of these
mechanisms.
Exceeding the maximum permissible
operating pressure may cause the
nailer to explode, blowing metal frag-
ments in all directions. To protect
yourself from serious personal injury,
DO NOT allow your air compressor to
exceed the recommended pressure
when connected to this nailer!
The safety yoke is
a
mechanical
device that can fail. Never rely on the
safety yoke mechanism as an excuse
to point the nailer at yourself or any
bystanders. Serious injury may occur.
-5-
G6045/G6046/G6047 18 Gauge Brad Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Operating Nailer
Loading Nailer
To load your nailer:
If you have not read the safety instruc-
tions in this manual, do not operate the
nailer.
1. Disconnect the air supply from the
nailer!
2. Flip the magazine latch in the direc-
tion shown in Figure 1.
Before you operate your nailer, place one
drop of the included oil into the quick con-
nect fitting where the nailer connects to the
air supply. Fire the EMPTY nailer 3-4 times
before beginning, so oil does not come out
onto the project during regular operation.
To operate your nailer:
1. Connect the air supply to the quick
connect fitting.
2. Test the loaded nailer for proper brad
penetration. Hold the nailer perpen-
dicular to the surface of a piece of
clean scrap wood that is thick enough
for the length of brad nails you have
loaded. Depress the safety yoke
mechanism on your workpiece.
3. Before pressing the trigger, make
sure your free hand is positioned out
of the way of a potential path of a brad
nail in case of deflection. (Deflection
is caused when grain irregularities,
knots or foreign objects inside the
wood cause the nail to change its
path, resulting in the nail puncturing
the surface of the workpiece as
shown in Figure 3.)
Figure 1. Releasing magazine latch.
3. Pull back the magazine cover until it
stops.
4. Point the nailer down and insert a
stick of brad nails into the magazine
as shown in Figure 2. Make sure that
the pointed ends of the nails rest in
the slot at the bottom of the magazine.
Figure 2. Loading brad nails into nailer.
5. Push the magazine cover forward
until the magazine latch locks in
place.
Figure 3. Example of brad nail deflection.
-6-
G6045/G6046/G6047 18 Gauge Brad Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
Besides damaging your workpiece,
deflection can cause injury if your free
hand is securing the workpiece in the
location that the nail deflects.
Cleaning Nailer
4. Press the trigger. If the brad nail drove
into the wood far enough, continue
with your intended operations. If the
brad nail either went too far or not far
enough, then adjust the air pressure.
More air pressure will make the brad
nail go deeper and less air pressure
will decrease the brad nail penetra-
tion.
Oiling Nailer
Never use use gasoline or other flam-
mable liquids to clean this tool.
Vapors in the tool may ignite, causing
the tool to explode. Ignoring this
warning may lead to serious personal
injury or even death!
Special oil has been included with your
new Grizzly nailer to help maintain its use-
ful life. Place one drop of oil in the nailer air
inlet (as shown in Figure 4) before every
use. Wipe off any excess oil near the nail-
er exhaust to avoid dust build-up. When
the oil that was included with the nailer has
been completely used, replace with Grizzly
Model G2820 pnuematic tool oil.
Use a good solvent to clean the nose
assembly of the nailer. Always be sure that
the nailer is dry before using it again.
Do not allow dust, chips, sand, etc. into the
air connectors or into the body of the nail-
er; this may result in leaks and damage to
the nailer and the air couplings.
Another option to manual oiling would be
to install a lubricator in your air compressor
line. If your air compressor line already has
a lubricator, then regular lubrication of your
nailer will not be necessary. Just make
sure there is always oil in the lubricator.
As mentioned before, the best option is to
install a filter/lubricator/regulator unit such
as the Grizzly Model H2333 in your air line.
Figure 4. Lubricating nailer via air inlet.
-7-
G6045/G6046/G6047 18 Gauge Brad Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Replace the driver guide cover and
snap the quick release latch back into
operating position.
Clearing Jammed Nails
The most frequent situation with any type
of nailer is a nail jam. A jammed nail must
be cleared before using the nailer again.
The two places where a nail can get
jammed are the magazine and the dis-
charge area.
Quick Release Latch
Driver Guide Cover
Figure 5. Removing guide cover.
To clear a jammed nail from the discharge
area on the Model G6046:
1. Disconnect the nailer from the air
supply! Remove all brad nails from
the magazine.
Always disconnect air from nailer
whenever clearing a jammed nail!
2. Loosen the 2 cap screws that secure
the driver guide cover to the driver
guide on the nose assembly. Slide the
driver guide cover toward the nose
and pull it over the 2 cap screws. See
Figure 6 to identify these parts.
3. The jammed nail should now be visi-
ble; remove it with needle nose pliers.
4. Install the guide cover and check the
safety yoke mechanism for proper
operation (following the same instruc-
tions as mentioned in the Safety sec-
tion).
To clear a jammed nail from the magazine:
1. Disconnect the nailer from the air
supply!
2. Open the magazine cover and pull the
magazine all the way back.
3. Locate and remove the jammed brad
nail with a pair of needle nose pliers.
Close the magazine cover so it latch-
es.
To clear a jammed nail from the discharge
area with the Model G6045/G6047:
1. Disconnect the nailer from the air
supply!
Guide Cover
Cap Screws
2. Remove all of the brad nails from the
magazine.
3. Flip up the quick release latch that is
located on top of the nailer nose
assembly as shown in Figure 5.
4. Remove the driver guide cover.
5. The jammed nail should now be visi-
ble; remove it from the discharge area
with needle nose pliers.
Figure 6. Removing guide cover.
-8-
G6045/G6046/G6047 18 Gauge Brad Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Pistons/O-Rings
If you use your nailer day in and day out,
Grizzly offers repair pistons as cheap
insurance against wasted down time and
lost profits in the event that a piston or pis-
ton shaft becomes worn out. To replace a
piston:
Figure 7. Removing rear cap.
6. Remove the guide cover from the
nose assembly by loosening the 2 cap
screws.
7. Watch the nose assembly and push
the top of the piston with your finger.
You will see the piston shaft slide
along the guide.
8. Push the piston shaft back inside the
nailer until you can grip the piston
head and remove it from the cylinder.
9. Place a new O-ring on the new piston
and apply a thin film of the proper
lubricating oil on the O-ring.
10. Insert the new piston in the cylinder.
Make sure that the grooves on the
piston shaft line up with those on the
guide. The new piston should easily
slide into the cylinder. Do not force
the piston into the cylinder! If the
piston is not easily inserted, double-
check the alignment of the piston
shaft with the grooves on the guide.
11. After the piston is inserted correctly,
replace the guide cover and tighten
the 2 cap screws. Replace the rear
cap assembly and tighten the 4 cap
screws.
Always disconnect air from nailer
whenever servicing! During mainte-
nance, a nailer connected to air may
fire accidentally, causing serious
personal injury!
1. Disconnect the nailer from the air
supply!
2. Remove all nails from the magazine
cartridge.
3. Remove the 4 cap screws on the back
of the nailer, near the exhaust port.
4. Remove the rear cap as shown in
Figure 7.
5. The top of the piston should now be
visible inside the cylinder, which is
housed in the back of the nailer.
12. For more assistance, or to install a
complete O-ring set, refer to the
appropriate breakdown diagram in the
back of this manual.
-9-
G6045/G6046/G6047 18 Gauge Brad Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
G6045 PART BREAKDOWN
-10-
G6045/G6046/G6047 18 Gauge Brad Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
01 P6045001 CAP SCREW
02 P6045002 LOCK WASHER
03 P6045003 CAP
42 P6045042 CAP SCREW
43 P6045043 LOCK WASHER
44 P6045044 DRIVER GUIDE CVR
45 P6045045 SET PLATE
46 P6045046 CAP SCREW
47 P6045047 DRIVER GUIDE
48 P6045048 MAGAZINE COVER
49 P6045049 SETSCREW
50 P6045050 MAGAZINE
51 P6045051 CAP SCREW
52 P6045052 TAIL COVER
53 P6045053 PUSHER
04 P6045004 SEAL
05 P6045005 SPRING
06 P6045006 O-RING
07 P6045007 CAP SEAL
08 P6045008 PISTON HEAD VALVE
08A P604500A PISTON HEAD ASSY
09 P6045009 O-RING
10 P6045010 STOPPER
11 P6045011 O-RING
12 P6045012 COLLAR
54 P6045054 SPRING
13 P6045013 O-RING
55 P6045055 NAIL GUIDE LINER
56 P6045056 LOCK WASHER
57 P6045057 CAP SCREW
58 P6045058 SHAFT
14A P6045014A DRIVER ASSEMBLY
18 P6045018 O-RING
19 P6045019 CYLINDER
19A P6045019A COLLAR
59 P6045059 STOPPER
60 P6045060 TORSION SPRING
61 P6045061 BRACKET
20 P6045020 BUMPER
21 P6045021 O-RING
22 P6045022 O-RING
62 P6045062 RETAINING RING
63 P6045063 CAP SCREW
64 P6045064 CAP SCREW
65 P6045065 LOCK NUT
66 P6045066 COVER
23 P6045023 BODY
24 P6045024 RETAINING RING
25 P6045025 JOINT GUIDE
26 P6045026 SPRING
27 P6045027 GUIDE SAFETY LVR
31 P6045031 SAFETY YOKE
32 P6045032 STEPPED PIN
33 P6045033 O-RING
67 P6045067 AIR PLUG
68 P6045068 O-RING
71 P6045071 LOCK NUT
72 P6045072 SPRING
34 P6045034 TRGR VALVE HEAD
35 P6045035 TRGR VALVE STEM
36 P6045036 O-RING
74 P6045074 EXHAUST COVER
75 P6045075 CAP SCREW
76 PRP50M
ROLL PIN 3 X 18
37 P6045037 O-RING
77 P6045077 RUBBER INLET PLUG
500 P6045500 PISTON/O-RING SET*
501 P6045501 CARRYING CASE*
502 P6045502 O-RING SET*
38 P6045038 TRGR VALVE GUIDE
39 P6045039 SPRING
40A P6045040A TRIGGER ASSEMBLY
41A P6045041A LATCH
* These items are not shown in the illustration.
-11-
G6045/G6046/G6047 18 Gauge Brad Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
G6046 PART BREAKDOWN
-12-
G6045/G6046/G6047 18 Gauge Brad Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
REF PART #
DESCRIPTION
REF PART #
41 P6045041
DESCRIPTION
01 P6046001 CAP SCREW
02 P6046002 LOCK WASHER
03 P6046003 CAP
42 P6046042 CAP SCREW
43 P6046043 LOCK WASHER
44 P6046044 DRIVER GUIDE CVR
45 P6046045 SET PLATE
46 P6046046 CAP SCREW
47 P6046047 DRIVER GUIDE
48 P6046048 MAGAZINE COVER
49 P6046049 SETSCREW
50 P6046050 MAGAZINE
51 P6046051 CAP SCREW
52 P6046052 TAIL COVER
53 P6046053 PUSHER
04 P6046004 SEAL
05 P6046005 SPRING
06 P6046006 O-RING
07 P6046007 CAP SEAL
08 P6046008 PISTON HEAD VALVE
08A P604600A PISTON HEAD ASSY
09 P6046009 O-RING
10 P6046010 STOPPER
11 P6046011 O-RING
12 P6046012 COLLAR
13 P6046013 O-RING
54 P6046054 SPRING
14A P6046014A DRIVER ASSEMBLY
18 P6046018 O-RING
55 P6046055 NAIL GUIDE LINER
56 P6046056 LOCK WASHER
57 P6046057 CAP SCREW
58 P6046058 SHAFT
19 P6046019 CYLINDER
19A P6046019A COLLAR
20 P6046020 BUMPER
21 P6046021 O-RING
59 P6046059 STOPPER
60 P6046060 TORSION SPRING
61 P6046061 BRACKET
22 P6046022 O-RING
23 P6046023 BODY
62 P6046062 RETAINING RING
63 P6046063 CAP SCREW
64 P6046064 CAP SCREW
65 P6046065 LOCK NUT
66 P6046066 COVER
24 P6046024 E-RING
25 P6046025 JOINT GUIDE
26 P6046026 SPRING
27 P6046027 GUIDE SAFETY LVR
31 P6045031 SAFETY YOKE
32 P6046032 STEPPED PIN
33 P6046033 O-RING
67 P6046067 AIR PLUG
68 P6046068 O-RING
71 P6046071 LOCK NUT
72 P6046072 SPRING
34 P6046034 TRGR VALVE HEAD
35 P6046035 TRGR VALVE STEM
36 P6046036 O-RING
74 P6046074 EXHAUST COVER
75 P6046075 CAP SCREW
77 P6046077 RUBBER INLET PLUG
500 P6046500 PISTON/O-RING SET*
501 P6046501 CARRYING CASE*
502 P6046502 O-RING SET*
37 P6046037 O-RING
38 P6046038 TRGR VALVE GUIDE
39 P6046039 SPRING
40A P6046040A TRIGGER ASSEMBLY
* These items are not shown in the illustration.
-13-
G6045/G6046/G6047 18 Gauge Brad Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
G6047 PART BREAKDOWN
-14-
G6045/G6046/G6047 18 Gauge Brad Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
01 P6047001 CAP SCREW
02 P6047002 LOCK WASHER
03 P6047003 CAP
42 P6047042 CAP SCREW
43 P6047043 LOCK WASHER
44 P6047044 DRIVER GUIDE CVR
45 P6047045 SET PLATE
46 P6047046 CAP SCREW
47 P6047047 DRIVER GUIDE
48 P6047048 MAGAZINE COVER
49 P6047049 SETSCREW
50 P6047050 MAGAZINE
51 P6047051 CAP SCREW
52 P6047052 TAIL COVER
53 P6047053 PUSHER
04 P6047004 SEAL
05 P6047005 SPRING
06 P6047006 O-RING
07 P6047007 CAP SEAL
08 P6047008 PISTON HEAD VALVE
08A P604700A PISTON HEAD ASSY
09 P6047009 O-RING
10 P6047010 STOPPER
11 P6047011 O-RING
12 P6047012 COLLAR
54 P6047054 SPRING
13 P6047013 O-RING
55 P6047055 NAIL GUIDE LINER
56 P6047056 LOCK WASHER
57 P6047057 CAP SCREW
58 P6047058 SHAFT
14A P6047014A DRIVER ASSEMBLY
18 P6047018 O-RING
19 P6047019 CYLINDER
19A P6047019A COLLAR
59 P6047059 STOPPER
60 P6047060 TORSION SPRING
61 P6047061 BRACKET
20 P6047020 BUMPER
21 P6047021 O-RING
22 P6047022 O-RING
62 P6047062 RETAINING RING
63 P6047063 CAP SCREW
64 P6047064 CAP SCREW
65 P6047065 LOCK NUT
66 P6047066 COVER
23 P6047023 BODY
24 P6047024 RETAINING RING
25 P6047025 JOINT GUIDE
26 P6047026 SPRING
27 P6047027 GUIDE SAFETY LVR
31 P6047031 SAFETY YOKE
32 P6047032 STEPPED PIN
33 P6047033 O-RING
67 P6047067 AIR PLUG
68 P6047068 O-RING
71 P6047071 LOCK NUT
72 P6047072 SPRING
34 P6047034 TRGR VALVE HEAD
35 P6047035 TRGR VALVE STEM
36 P6047036 O-RING
74 P6047074 EXHAUST COVER
75 P6047075 CAP SCREW
76 PRP50M
ROLL PIN 3 X 18
37 P6047037 O-RING
77 P6047077 RUBBER INLET PLUG
500 P6047500 PISTON/O-RING SET*
501 P6047501 CARRYING CASE*
502 P6047502 O-RING SET*
38 P6047038 TRGR VALVE GUIDE
39 P6047039 SPRING
40A P6047040A TRIGGER ASSEMBLY
41A P6047041 LATCH
* These items are not shown in the illustration.
-15-
G6045/G6046/G6047 18 Gauge Brad Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
CAUSE
PROBLEM
ACTION
1. O-rings in trigger valve
housing are damaged.
1. O-rings must be replaced
Air leaking at trigger valve
area.
&
operation of safety
yoke must be checked.
1. Loose screws in housing.
2. Damaged O-ring.
3. Damaged bumper.
1. Tighten screws.
2. Replace O-ring.
3. Replace bumper.
Air leaking between hous-
ing and hose.
1. Damaged seal.
1. Air leaks.
1. Replace damaged seals.
Air leaking between hous-
ing and cap assembly.
1. Tighten screws and fit-
tings.
Tool skips nails while dis-
charging.
2. Dirt in nose.
2. Clean nose.
3. Dirt or damage prevents
nails from moving freely in
magazine.
3. Clean magazine and
inspect/repair damage.
4. Inadequate air flow to tool.
4. Check fitting, air hose,
and air compressor.
5. Replace piston O-ring.
Lubricate.
5. Worn O-ring on piston or
lack of lubrication.
6. Damaged O-rings on trigger
valve.
6. Replace trigger valve O-
rings.
7. Worn bumper.
8. Cap seal leaking.
7. Replace bumper.
8. Replace cap seal.
1. Nailer is not sufficiently lubri-
cated.
2. Broken spring in cap
assembly.
1. Lubricate nailer.
2. Replace spring.
Tool runs slowly or has a
loss of power.
3. Exhaust port in cap is
blocked.
3. Replace damaged inter-
nal parts.
1. Nails are the wrong size.
2. Nails are bent.
3. Magazine or nose screws
are loose.
1. Use correct nails.
2. Use undamaged nails
3. Tighten magazine and
nose screws.
Fasteners frequently jam
the nailer.
4. Driver or driver guide are
worn or damaged.
4. Replace worn or dam-
aged parts.
1. Nail is jammed in maga-
zine or discharge area.
1. Clear nailer magazine or
discharge area.
Nailer does not fire.
2. Piston shaft is damaged.
3. Air pressure too low.
2. Replace piston shaft.
3. Check/increase air pres-
sure.
-16-
G6045/G6046/G6047 18 Gauge Brad Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main-
tenance. This is Grizzly’s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are here-
by limited to the duration of this written warranty. We do not warrant or represent that the
merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, con-
tingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Number,” which must be clearly posted on the outside as
well as the inside of the carton. We will not accept any item back without this number. Proof
of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they con-
stantly strive to achieve better quality equipment. We make every effort to ensure that our
products meet high quality and durability standards and we hope you never need to use this
warranty.
Please feel free to write or call us if you have any questions about the machine or the man-
ual.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Pennsdale, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
Thank you again for your business and continued support. We hope to serve you again
soon!
-17-
G6045/G6046/G6047 18 Gauge Brad Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name__________________________________________________________
Street__________________________________________________________
City____________________State________Zip_________
Phone Number____________E-Mail___________________FAX____________
Model #___________________________ Order #_______________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help
us develop better products and services. Of course, all information is strictly confidential.
9. How many of the machines checked above are
Grizzly? ____________
1. How did you learn about us?
___Advertisement
___Friend
___Catalog
___World Wide Web
___Other__________________________
___Card Deck
10. Which portable/hand held power tools do you own?
Check all that apply.
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
2. What is your annual household income?
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
___Miter Saw
___Other_________________________________
3. What is your age group?
___20-29
11. What machines/supplies would you like Grizzly
Industrial to carry?
___50-59
___60-69
___70 +
___30-39
___40-49
________________________________________
________________________________________
________________________________________
________________________________________
4. How long have you been a woodworker?
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
12. What new accessories would you like Grizzly
Industrial to carry?
5. How would you rank your woodworking skills?
________________________________________
________________________________________
________________________________________
________________________________________
___Simple
___Advanced
___Intermediate
___Master Craftsman
6. What stationary woodworking tools do you own?
Check all that apply.
13. What other companies do you purchase your tools
and supplies from?
___Air Compressor
___Band Saw
___Panel Saw
___Planer
_________________________________________
_________________________________________
_________________________________________
___Drill Press
___Power Feeder
___Radial Arm Saw
___Shaper
___Jointer
___Lathe
___Drum Sander
___Dust Collector
___Spindle Sander
___Table Saw
14. Do you think your purchase represents good value?
___Yes
___No
___Mortiser
___Wide Belt Sander
___Horiz.Boring Machine
___Vacuum Veneer Press
___Other______________________________
15. Would you recommend Grizzly to a friend?
___Yes ___No
16. Would you allow us to use your name as a refer-
ence for Grizzly customers in your area? Note: We
never use names more than three times.
7. How many of your woodworking machines are
Grizzly? _____________
___Yes
___No
8. Which benchtop tools do you own? Check all
that apply.
17.Comments:________________________________
_________________________________________
_________________________________________
_________________________________________
___1"x42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
___8" Table Saw
___Scroll Saw
___8" - 10" Bandsaw
___Disc/Belt Sander
___Spindle/Belt Sander ___Mini Jointer
___10"-12"Thickness Planer
___Other______________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
Send a Grizzly Catalog to a friend:
Name________________________________
Street________________________________
City______________State______Zip_______
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
|