MODEL G0675
10" JOINTER/PLANER
COMBO MACHINE
OWNER'S MANUAL
COPYRIGHT © NOVEMBER, 2008 BY GRIZZLY INDUSTRIAL, INC., REVISED SEPTEMBER, 2013 (ST)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BL11208 PRINTED IN CHINA
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
SECTION 6: MAINTENANCE......................... 32
INTRODUCTION............................................... 2
Manual Accuracy ........................................... 2
Contact Info.................................................... 2
Functional Overview ...................................... 2
Identification................................................... 3
Machine Data Sheet ...................................... 4
Schedule...................................................... 32
Cleaning....................................................... 32
Belts............................................................. 32
Lubrication ................................................... 34
SECTION 7: SERVICE ................................... 37
Troubleshooting ........................................... 37
Jointer Table Parallelism ............................. 39
Inspecting Knives......................................... 42
Adjusting/Replacing Knives ......................... 43
Setting Fence Stops .................................... 44
Spring Tension............................................. 46
Replacing Feed Rollers ............................... 47
Chain Tension.............................................. 48
Planer Table Parallelism.............................. 49
Anti-Kickback Fingers.................................. 51
SECTION 1: SAFETY....................................... 6
Safety Instructions for Machinery .................. 6
Additional Safety Instructions for Jointers ..... 8
Additional Safety Instructions for Planers...... 9
SECTION 2: CIRCUIT REQUIREMENTS ...... 10
220V Operation............................................ 10
SECTION 3: SETUP ....................................... 11
Items Needed for Setup............................... 11
Unpacking.................................................... 11
Inventory ...................................................... 12
Clean Up...................................................... 12
Site Considerations...................................... 13
Moving & Placing Base Unit ........................ 13
Mounting to Shop Floor ............................... 14
Assembly ..................................................... 15
Dust Collection............................................. 16
Setting Outfeed Table Height ...................... 17
Test Run ...................................................... 18
Recommended Adjustments........................ 19
Belt Break-In................................................ 19
SECTION 8: WIRING...................................... 52
Wiring Safety Instructions............................ 52
Wiring Overview........................................... 53
ON/OFF Switch Assembly Wiring................ 54
Components Wiring ..................................... 55
SECTION 9: PARTS....................................... 56
Table Breakdown......................................... 56
Motor Assembly Breakdown........................ 57
Frame Breakdown........................................ 58
Fence Assembly Breakdown ....................... 59
Feed Gear Assembly Breakdown................ 60
Cutterhead-Feed Rollers Breakdown .......... 62
Access Panels Breakdown .......................... 63
Base Breakdown.......................................... 64
Planer Table Breakdown ............................. 65
Labels and Cosmetic Parts.......................... 66
SECTION 4: OPERATIONS ........................... 20
Basic Jointer Controls.................................. 20
Basic Planer Controls .................................. 22
Jointer-Planer Conversion ........................... 22
Stock Inspection and Requirements............ 24
Squaring Stock............................................. 25
Surface Planing............................................ 26
Edge Jointing............................................... 28
Bevel Cutting................................................ 29
Thickness Planer Operation ........................ 30
WARRANTY AND RETURNS ........................ 69
SECTION 5: ACCESSORIES......................... 31
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Manual Accuracy
Functional Overview
We are proud to offer this manual with your new
machine! We've made every effort to be exact
with the instructions, specifications, drawings, and
photographs of the machine we used when writ-
ing this manual. However, sometimes errors do
happen and we apologize for them.
This jointer/planer can flatten the face or edge of
rough and warped stock, and reduce the thick-
ness of workpieces.
This jointer/planer shares a single cutterhead,
which features two steel knives that remove the
bottom face of the workpiece in jointer mode or
the top surface of the workpiece in planer mode.
Also, owing to our policy of continuous improve-
ment, your machine may not exactly match
the manual. If you find this to be the case, and
the difference between the manual and machine
leaves you in doubt, immediately call our techni-
cal support for updates or clarification.
The key features of the jointer are the outfeed and
infeed tables and fence, and the main features of
the planer are the planing table and the powered
feed rollers.
For your convenience, we always keep current
Grizzly manuals and most updates available on
your machine will be reflected in these documents
as soon as they are complete. Visit our site often
to check for the latest updates!
To square up a piece of rough stock, the infeed
table is lowered a desired amount. The stock is
placed firmly on the jointer infeed table and against
the fence. While using the fence as a guide, the
workpiece is moved over the cutterhead, where the
knives make numerous shallow cuts that “shave”
off the surface of the workpiece. The workpiece
is received by the outfeed table, which along
with the fence, continue to guide the workpiece
across a flat plane until it completely passes the
cutterhead. This process is repeated a number of
times to yield the desired cut.
Contact Info
We stand behind our machines. If you have any
service questions, parts requests or general ques-
tions about the machine, please call or write us at
the location listed below.
After the machine is converted to planer mode,
the operator adjusts the table height according
to the stock thickness and the desired depth of
cut. The face of the previously squared-up stock
is placed on the table, the workpiece is pushed
into the machine, where the infeed roller grabs
it and draws it into the cutterhead knives. The
powered outfeed roller pulls the workpiece out of
the cutterhead and delivers it to the outfeed table.
This process is repeated until the board is smooth
on one side. The board can be flipped over again
and planed on the other side until it is smooth, or it
can be edge joined after the machine is converted
back to a jointer.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
If you have any comments regarding this manual,
please write to us at the address below:
Grizzly Industrial, Inc.
Technical Documentation Manager
P.O. Box 2069
C
/
O
Bellingham, WA 98227-2069
Email: [email protected]
-2-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification
C
B
P
A
D
O
E
X
Y
F
Q
N
R
S
W
M
L
G
T
V
U
H
K
I
J
Figure 1. G0675 identification.
A. Fence
B. Fence Height Lock Knob
C. Fence Tilt Lock
M. Planer Table
N. Rear Access Panel
O. Outfeed Table Lock Arm
D. Blade Guard Lock Knob
E. Blade Guard
F. Infeed Table
P. Dust Chute Assembly (Planer Operations)
Q. Dust Chute Lock
R. Outfeed Table Lock
G. Fence Lock Lever
H. Infeed Table Adjustment Lever
I. Base
S. Planer Table Height Indicator
T. Planer Table Height Scale
U. On/Off Switch
J. Foot
V. 4" Dust Port (Jointer Operations)
W. Blade Guard Arm Lock Lever
X. Blade Guard Arm Adjustment Knob
Y. Outfeed Table
K. Front Access Panel
L. Planer Table Height Handwheel
-3-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Machine Data Sheet
mACHINe dATA
SHeeT
Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901
model G0675
JoINTeR/PlANeR ComBINATIoN mACHINe
Product Dimensions:
Weight .............................................................................................................................................................317 lbs.
Length/Width/Height ............................................................................................................................46" x 27" x 38"
Foot Print (Length/Width)...............................................................................................................................26" x 22"
Shipping Dimensions:
Carton #1
Type ................................................................................................................................................Wood Crate
Content..................................................................................................................................................Machine
Weight....................................................................................................................................................348 lbs.
Length/Width/Height.................................................................................................................. 44" x 25" x 25"
Carton #2
Type .................................................................................................................................................. Cardboard
Content....................................................................................................................................................... Base
Weight......................................................................................................................................................30 lbs.
Length/Width/Height.................................................................................................................... 29" x 14" x 7"
Electrical:
Switch................................................................................................................................................... On/Off Buttons
Switch Voltage .....................................................................................................................................................220V
Recommended Cord Gauge........................................................................................................................ 14 Gauge
Recommended Breaker Size................................................................................................................................ 15A
Plug............................................................................................................................................................NEMA 6-15
Motors:
Main
Type .................................................................................................................TEFC Capacitor Start Induction
Horsepower............................................................................................................................................. 2.5 HP
Voltage.......................................................................................................................................................220V
Phase....................................................................................................................................................... Single
Amps...........................................................................................................................................................9.9A
Speed................................................................................................................................................ 3400 RPM
Cycle .........................................................................................................................................................60 Hz
Number Of Speeds .......................................................................................................................................... 1
Power Transfer ................................................................................................................................ Poly V-Belt
Bearings...................................................................................................................... Shielded and Lubricated
Main Specifications:
Fence Information
Fence Length............................................................................................................................................357/16"
Fence Height................................................................................................................................................57/8
"
Fence Stops...............................................................................................................................45 and 90 deg.
Cutting Capacities (Jointer)
Bevel Jointing .....................................................................................................................................0-45 deg.
Maximum Width of Cut ..............................................................................................................................101/4
"
"
Maximum Depth of Cut..................................................................................................................................1/8
Number of Cuts Per Minute ..................................................................................................................... 13000
-4-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Cutting Capacities (Planer)
Maximum Width of Cut ................................................................................................................................93/4
"
Maximum Depth of Cut Planing Full Width...................................................................................................3/16"
Number of Cuts Per Minute ..................................................................................................................... 13000
Number of Feed Speeds.................................................................................................................................. 1
Feed Speed ...........................................................................................................................................16 FPM
Minimum Stock Length ........................................................................................................................... 1113/16"
Maximum Stock Thickness ..........................................................................................................................81/4
"
Knife Information (Jointer)
Number of Knives ............................................................................................................................................ 2
Knife Type...................................................................................................................................................HSS
Knife Length...............................................................................................................................................101/4
"
Knife Width.................................................................................................................................................. 11/16"
Knife Thickness..............................................................................................................................................1/8
Knife Adjustment............................................................................................................................Jack Screws
"
Cutterhead Information
Cutterhead Type ..........................................................................................................................2 HSS Knives
Cutterhead Diameter...................................................................................................................................29/32"
Cutterhead Speed............................................................................................................................. 6500 RPM
Table Information (Jointer)
Table Length........................................................................................................................................... 4015/16"
Table Width................................................................................................................................................121/2
Floor To Table Height................................................................................................................................333/4
"
"
Table Information (Planer)
Table Length..............................................................................................................................................231/8
Table Width..................................................................................................................................................93/4
Table Thickness...........................................................................................................................................11/2
"
"
"
Floor To Table Height.............................................................................................................................23"-30"
Construction
Body Assembly Construction..........................................................................................................Sheet Metal
Cutterhead Assembly Construction ........................................................................................................... Steel
Infeed Roller Construction ........................................................................ Steel w/Vulcanized Rubber Coating
Outfeed Roller Construction...................................................................... Steel w/Vulcanized Rubber Coating
Jointer Table Construction...................................................................................................................Cast Iron
Paint.......................................................................................................................................... Powder Coated
Other Infomation
Dust Port Size.................................................................................................................................................4"
Number of Dust Ports ...................................................................................................................................... 1
Measurement Scale (Jointer)....................................................................................................................... mm
Measurement Scale (Planer) ....................................................................................................................... mm
Other Specifications:
Country Of Origin................................................................................................................................................China
Warranty.............................................................................................................................................................1 Year
Serial Number Location ...............................................................................................ID Label on Front of the Stand
Features:
Quick release fence
Flip up outfeed table and change lever simplify jointer-planer conversion
Vulcanized rubber feed rollers (planer mode)
Heavy duty cast iron infeed and outfeed tables, easily and accurately adjustable
Cutterhead guard adjustable for workpiece height
Dust hood position adjustable for jointer or planer conversion
-5-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SAFETY
For Your Own Safety, Read Instruction
Manual Before Operating this Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This
manual uses a series of symbols and signal words intended to convey the level of importance
of the safety messages. The progression of symbols is described below. Remember that safety
messages by themselves do not eliminate danger and are not a substitute for proper accident
prevention measures.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
This symbol is used to alert the user to useful information about
proper operation of the machine.
NOTICE
Safety Instructions for Machinery
OWNER’S MANUAL. Read and understand
this owner’s manual BEFORE using machine.
Untrained users can be seriously hurt.
WEARING PROPER APPAREL. Do not wear
clothing, apparel, or jewelry that can become
entangled in moving parts. Always tie back or
cover long hair. Wear non-slip footwear to avoid
accidental slips which could cause a loss of
workpiece control.
EYE PROTECTION. Always wear ANSI-
approved safety glasses or a face shield when
operating or observing machinery. to reduce
the risk of eye injury or blindness from fly-
ing particles Everyday eyeglasses are not
approved safety glasses.
HEARING PROTECTION. Always wear hear-
ing protection when operating or observiing loud
machinery. Extended exposure to this noise
without hearing protection can cause permanent
hearing loss.
HAzARDOUS DUST. Dust created while using
machinery may cause cancer, birth defects,
or long-term respiratory damage. Be aware of
dust hazards associated with each workpiece
material, and always wear a NIOSH-approved
respirator to reduce your risk.
MENTAL ALERTNESS. Be mentally alert when
running machinery. Never operate under the
influence of drugs or alcohol, when tired, or when
distracted.
-6-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions for Machinery
DISCONNECTING POWER SUPPLY. Always
APPROVED OPERATION. Untrained operators
can be seriously hurt by machinery. Only allow
trained or properly supervised people to use
machine. When machine is not being used, dis-
connect power, remove switch keys, or lock-out
machine to prevent unauthorized use—especially
around children. Make workshop kid proof!
disconnect machine from power supply before
servicing, adjusting, or changing cutting tools
(bits, blades, cutters, etc.). Make sure switch is
in OFF position before reconnecting to avoid an
unexpected or unintentional start.
INTENDED USE. Only use the machine for its
intended purpose and only use recommended
accessories. Never stand on machine, modify
it for an alternative use, or outfit it with non-
approved accessories.
CHILDREN & BYSTANDERS. Keep children
and bystanders a safe distance away from work
area. Stop using machine if children or bystand-
ers become a distraction.
STABLE MACHINE. Unexpected movement
during operations greatly increases the risk of
injury and loss of control. Verify machines are
stable/secure and mobile bases (if used) are
locked before starting.
FEED DIRECTION. Unless otherwise noted, feed
work against the rotation of blades or cutters.
Feeding in the same direction of rotation may pull
your hand into the cut.
SECURING WORKPIECE. When required, use
clamps or vises to secure workpiece. A secured
workpiece protects hands and frees both of them
to operate the machine.
FORCINGMACHINERY.Donotforcemachine.
It will do the job safer and better at the rate for
which it was designed.
UNATTENDED OPERATION. Never leave
machine running while unattended. Turn machine
Off and ensure all moving parts completely stop
before walking away.
GUARDS & COVERS. Guards and covers can
protect you from accidental contact with mov-
ing parts or flying debris. Make sure they are
properly installed, undamaged, and working
correctly before using machine.
MAINTENANCE & INSPECTION. A machine that
is not properly maintained may operate unpre-
dictably. Follow all maintenance instructions and
lubrication schedules to keep machine in good
working condition. Regularly inspect machine for
loose bolts, alignment of critical parts, binding, or
any other conditions that may affect safe opera-
tion. Always repair or replace damaged or mis-
adjusted parts before operating machine.
REMOVING TOOLS. Never leave adjustment
tools, chuck keys, wrenches, etc. in or on
machine—especially near moving parts. Verify
removal before starting!
AWKWARD POSITIONS. Keep proper foot-
ing and balance at all times when operating
machine. Do not overreach! Avoid awkward
hand positions that make workpiece control dif-
ficult or increase the risk of accidental injury.
EXPERIENCING DIFFICULTIES. If at any time
you are experiencing difficulties performing the
intended operation, stop using the machine!
Contact our Technical Support Department at
(570) 546-9663.
DANGEROUS ENVIRONMENTS. Do not use
machinery in wet locations, cluttered areas,
around flammables, or in poorly-lit areas. Keep
work area clean, dry, and well lighted to mini-
mize risk of injury.
-7-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety Instructions for Jointers
7. CUTTING LIMITATIONS. The jointer may
kick out a workpiece at the operator or be
damaged if pushed beyond these limits.
1. JOINTER KICKBACK. "Kickback" is when
the workpiece is thrown off the jointer table
by the force of the cutterhead. Always use
push blocks and safety glasses to reduce
the likelihood of injury from “kickback.” If
you do not understand what kickback is,
or how it occurs, DO NOT operate this
machine.
•
•
•
Maximum Depth of Cut......................1⁄8
"
"
Maximum Width of Cut .................. 101⁄4
Minimum Length ............................... 12"
8. JOINTING WITH THE GRAIN. Jointing against
the grain or jointing end grain is dangerous
and could produce chatter or excessive chip-
out. Always joint with the grain.
2. CUTTERHEAD ALIGNMENT. Keep the top
edge of the outfeed table aligned with the
cutterhead knife at top dead center (TDC)
to avoid kickback and personal injuries.
9. KEEPING GUARDS IN PLACE. All opera-
tions must be performed with the cutterhead
guard in place.
3. PUSH BLOCKS. Always use push blocks
whenever surface planing. Never pass your
hands directly over the cutterhead without a
push block.
10. PROPER CUTTING. When cutting, always
keep the workpiece moving toward the outfeed
table until the workpiece has passed com-
pletely over the cutterhead. Never back the
work toward the infeed table.
4. WORKPIECE SUPPORT. Supporting the
workpiece adequately at all times while
cutting is crucial for making safe cuts and
avoiding injury. Never attempt to make a cut
with an unstable workpiece.
11. USING GOOD STOCK. Jointing safety begins
with your lumber. Inspect your stock carefully
before you feed it over the cutterhead. Never
joint a board that has loose knots, nails, or
staples. If you have any doubts about the sta-
bility or structural integrity of your stock, DO
NOT joint it!
5. KICKBACK ZONE. The "kickback zone"
is the path directly through the end of the
infeed table. Never stand or allow others to
stand in this area during operation.
6. MAXIMUM CUTTING DEPTH. The maxi-
1
mum cutting depth for one pass is ⁄8".
Never attempt any single cut deeper than
this!
Like all machines there is danger associated
with this machine. Accidents are frequently
caused by lack of familiarity or failure to pay
attention. Use this machine with respect
and caution to lessen the possibility of
operator injury. If normal safety precautions
are overlooked or ignored, serious personal
injury may occur.
No list of safety guidelines can be complete.
Every shop environment is different. Always
consider safety first, as it applies to your
individual working conditions. Use this and
other machinery with caution and respect.
Failure to do so could result in serious per-
sonal injury, damage to equipment, or poor
work results.
-8-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety Instructions for Planers
1. KICKBACK."Kickback"iswhentheworkpiece
is thrown off the planer table by the force of
the cutterhead. If you do not understand
what kickback is, or how it occurs, DO NOT
operate this machine.
8. CUTTING LIMITATIONS. The planer may
kick out a workpiece at the operator or be
damaged if pushed beyond these limits.
•
•
•
•
Maximum Depth of Cut.....................3⁄16"
Maximum Width of Cut ..................927⁄32"
Minimum Board Length..................... 12"
Maximum Board Thickness ............. 81⁄4
"
2. REACHING INSIDE PLANER. Never reach
inside the planer or remove covers when the
planer is connected to power.
9. CLEAN STOCK. Only plane clean stock.
Planing stock with nails, staples, or imbed-
ded stone will damage your knives and may
cause a fire hazard if the dust collector cap-
tures sparks or hot particles that have con-
tacted the knives. Always thoroughly inspect
and prepare stock to avoid these hazards.
3. INFEED CLEARANCE SAFETY. The infeed
roller is designed to pull material into the
cutterhead. Always keep hands, clothing,
and long hair away from the infeed roller dur-
ing operation to prevent serious injury.
4. BODY POSITION WHILE OPERATING. The
workpiece may kick out during operation.
To avoid getting hit, stand to the side of the
planer during the entire operation.
10. REMOVING JAMMED WORKPIECES. To
avoid serious injury, always stop the plan-
er and disconnect power before removing
jammed workpieces.
5. PLANING CORRECT MATERIAL. Only
plane natural wood stock with this planer.
DO NOT plane MDF, plywood, laminates, or
other synthetic products.
11. DULL/DAMAGED KNIVES. The planer may
kick out a workpiece at the operator or give
poor finish results if it is operated with dull or
damaged knives.
6. GRAIN DIRECTION. Planing across the
grain is hard on the planer and may cause
the workpiece to kick out. Always plane in
the same direction or at a slight angle with
the wood grain.
12. UNPLUGGING DURING ADJUSTMENTS.
When connected to power, the planer can
be accidentally turned ON. Always discon-
nect power when servicing or adjusting the
components of the planer.
7. LOOKING INSIDE PLANER. Wood chips
fly around inside the planer at a high rate
of speed. DO NOT look inside the planer or
remove guards/covers when the planer is
connected to power or during operation.
13. WORKPIECE CLEARANCE. Always verify
workpiece has enough room to exit the plan-
er before starting.
-9-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: CIRCUIT REQUIREMENTS
Power Connection Device
220V Operation
The Model G0675 comes with a 6-15 plug, similar
to Figure 2 to connect the machine to power.
GROUNDED
Serious personal injury could occur if you
6-15 RECEPTACLE
connect the machine to power before com-
Current Carrying Prongs
pleting the setup process. DO NOT connect
the machine to the power until instructed
later in this manual.
6-15 PLUG
Grounding Prong
Electrocution or fire could
result if machine is not
grounded and installed in
compliance with electrical
codes. Compliance MUST
be verified by a qualified
electrician!
Figure 2. NEMA 6-15 plug and receptacle.
Extension Cords
Using extension cords may reduce the life of the
motor. Instead, place the machine near a power
source. If you must use an extension cord:
Full Load Amperage Draw
This machine draws the following amps under
maximum load:
•
•
•
Use at least a 14 gauge cord that does not
exceed 50 feet in length!
The extension cord must also have a ground
wire and plug pin.
Amp Draw.............................................9.9 Amps
A qualified electrician MUST size cords over
50 feet long to prevent motor damage.
Power Supply Circuit Requirements
The power supply circuit for your machine MUST
be grounded and rated for the amperage given
below. Never replace a circuit breaker on an exist-
ing circuit with one of higher amperage without
consulting a qualified electrician to ensure compli-
ance with wiring codes. If you are unsure about
the wiring codes in your area or you plan to
connect your machine to a shared circuit, con-
sult a qualified electrician.
Minimum Circuit Size............................. 15 Amps
-10-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: SETUP
Items Needed for
This machine presents
serious injury hazards
to untrained users. Read
through this entire manu-
al to become familiar with
the controls and opera-
tions before starting the
machine!
Setup
The following items are needed to complete the
setup process, but are not included with your
machine:
Description
Qty
•
•
•
•
•
•
•
•
•
Safety Glasses for Each Person ................ 1
Power Lifting Equipment ............................ 1
Dust Collection System.............................. 1
4" Dust Hose (length as needed)............... 1
4" Hose Clamp ........................................... 1
Shop Rags and Cleaning Solvent ...... Varies
Wrench 16mm ............................................ 1
Precision Level ........................................... 1
Lifting Help/Assistant.................................. 1
Wear safety glasses dur-
ing the entire setup pro-
cess!
This machine and its com-
ponents are very heavy.
Get lifting help or use
power lifting equipment
such as a forklift to move
heavy items.
Unpacking
Your machine was carefully packaged for safe
transportation. Remove the packaging materials
from around your machine and inspect it. If you
discover the machine is damaged, please imme-
diately call Customer Service at (570) 546-9663
for advice.
Save the containers and all packing materials for
possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
When you are completely satisfied with the condi-
tion of your shipment, inventory the contents.
-11-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Inventory
Clean Up
The following is a description of the main compo-
nents shipped with your machine. Lay the compo-
nents out to inventory them.
The unpainted surfaces are coated with a waxy
oil to prevent corrosion during shipment. Remove
this protective coating with a solvent cleaner or
degreaser, such as shown in Figure 4. For thor-
ough cleaning, some parts must be removed.
For optimum performance, clean all moving
parts or sliding contact surfaces. Avoid chlo-
rine-based solvents, such as acetone or brake
parts cleaner that may damage painted surfac-
es. Always follow the manufacturer’s instructions
when using any type of cleaning product.
Note: If you can't find an item on this list, check
the mounting location on the machine or examine
the packaging materials carefully. Occasionally
we pre-install certain components for shipping
purposes.
Box 1: (Figure 3)
Qty
A. Jointer/Planer Unit (not shown) .................. 1
B. Fence Assembly......................................... 1
C. Blade Guard Arm Assembly....................... 1
D. Blade Guard ............................................... 1
E. Blade Adjustment Gauge ........................... 1
F. Dust Port .................................................... 1
G. Hex Wrench 5mm....................................... 1
H. Wrench 8/10mm ......................................... 1
Gasoline and petroleum
products have low flash
points and can explode
or cause fire if used to
clean machinery. DO
NOT use these products
to clean the machinery.
C
D
E
B
Many cleaning solvents
are toxic if inhaled.
Minimize your risk by only
using these products in a
well ventilated area.
F
G
G2544—Solvent Cleaner & Degreaser
H9692—Orange Power Degreaser
H
Great products for removing shipping grease.
Figure 3. G0675 inventory.
If any nonproprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
SUFFOCATION HAZARD!
Immediately discard all plas-
tic bags and packing materi-
als to eliminate choking/suf-
focation hazards for children
and animals.
Figure 4. Cleaner/degreasers available from
Grizzly.
-12-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Site Considerations
Moving & Placing
Base Unit
Floor Load
Refer to the Machine Data Sheet for the weight
and footprint specifications of your machine.
Some residential floors may require additional
reinforcement to support both the machine and
operator.
The Model G0675 is a
heavy machine. Serious
personal injury may occur
if safe moving methods
are not used. To be safe,
get assistance and use
power equipment to move
the shipping crate and
remove the machine from
the crate.
Placement Location
Consider existing and anticipated needs, size of
material to be processed through each machine,
and space for auxiliary stands, work tables or
other machinery when establishing a location for
your new machine. See Figure 5 for the minimum
working clearances.
Use a forklift to lift the jointer/planer just enough
to clear the shipping pallet and floor obstacles,
then move it to a suitable location, as shown in
Figure 6.
220V
15A
4" Dust
Collection Port
50"
Jointer Mode
220V
15A
4" Dust
Collection Port
Figure 6. Lifting model G0675 with a forklift.
43½"
Planer Mode
If you are unsure how to lift this machine, consult
a qualified professional.
Figure 5. Minimum working clearances.
Place a level on the table and level the machine
front-to-back and side-to-side by adjusting the
height of the feet. Raise or lower each rubber
foot by turning the hex nut above each foot with a
16mm wrench, then tighten the top locking nut.
Children and visitors may be
seriously injured if unsuper-
vised around this machine.
Lock entrances to the shop
or disable start switch or
power connection to prevent
unsupervised use.
If you have trouble adjusting the feet, unlatch the
top from the base and, with the help of an assis-
tant, set it aside. Adjust the feet, level the base,
secure the hex nuts, then reinstall the top with the
assistant's help.
-13-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Bolting to Concrete Floors
Mounting to Shop
Floor
Lag shield anchors with lag bolts (Figure 9) and
anchor studs are two popular methods for anchor-
ing an object to a concrete floor. We suggest
you research the many options and methods for
mounting your machine and choose the best that
fits your specific application.
Although not required, we recommend that you
mount your new machine to the floor. Because
this is an optional step and floor materials may
vary, floor mounting hardware is not included.
NOTICE
To mount the base to the floor:
Anchor studs are stronger and more per-
manent alternatives to lag shield anchors;
however, they will stick out of the floor,
which may cause a tripping hazard if you
decide to move your machine.
1. Unlatch the machine top from the base at
both ends (Figure 7).
Anchor Stud
Lag Bolt & Lag Shield Anchor
Figure 7. Location of latches.
Figure 9. Typical fasteners for mounting to
2. With the help of an assistant set the machine
concrete floors.
top aside.
3. Remove the rubber feet and install 10mm or
3
⁄8" bolts through the mounting holes (Figure
8) .
Figure 8. Base mounting holes.
4. Level the base with a precision level and
shims, as needed.
5. Set the machine top back on the base and
secure the latches.
-14-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip: Try tightening one cap screw several turns,
Assembly
then repeat with other until both are tight.
3. Loosen the guard lock knob, slide the blade
guard into the bracket, then tighten the lock
knob (see Figure 12).
This section covers how to setup your machine
for jointing operations. Once you have completed
the assembly and Test Run (Page 18), you can
convert the machine for planer operation (refer to
Page 22).
To assemble the machine:
Guard Lock
Knob
1. Pull up on the fence lock lever, then place the
fence assembly onto the table fence rail, as
shown in Figure 10.
Blade Guard
Fence Rail
Bracket
Figure 12. Blade guard installed.
To raise the blade guard, turn the height
adjustment knob counterclockwise (Figure
11); to lower the blade guard, turn the knob
clockwise.
Handle
Bracket
Lock
Lever
4. Loosen the thumb screw on the dust hood
assembly, insert the dust port into the dust
hood assembly, then tighten the thumb screw
(see Figure 13). Make sure the fingers on the
dust hood slide all the way into the grooves
on the port.
Figure 10. Fence installed.
2. Engage the blade guard lever, align the cap
screws on the arm with the mounting holes
on the outfeed table, then tighten the screws
(see detail in Figure 11).
Guard
Guard
Lever
Arm
Height
Knob
Thumb
Screw
Dust Port
Dust Hood
Assembly
Figure 13. Installing dust port.
Figure 11. Blade guard arm installed.
-15-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Dust Collection
DO NOT operate the Model G0675 with-
out an adequate dust collection system.
This machine creates substantial amounts
of wood dust while operating. Failure to use
a dust collection system can result in long-
term respiratory illness.
Recommended CFM at Dust Port: 400 CFM
Do not confuse this CFM recommendation with
the rating of the dust collector. To determine the
CFM at the dust port, you must consider these
variables: (1) CFM rating of the dust collector,
(2) hose type and length between the dust col-
lector and the machine, (3) number of branches
or wyes, and (4) amount of other open lines
throughout the system. Explaining how to cal-
culate these variables is beyond the scope of
this manual. Consult an expert or purchase a
good dust collection "how-to" book.
Figure 15. Dust hose attached to dust port setup
for planer operations.
Refer to the instructions on Page 22 (Planer
Operations Setup) for setting up the dust
chute for planer operations.
2. Tug the hose to make sure it does not come
off.
Note: A tight fit is necessary for proper per-
formance.
To connect a dust collection hose:
1. Fit the 4" dust hose over the dust port when
it is correctly positioned for jointer operation
(Figure 14) or planer operation (Figure 15),
and secure in place with a hose clamp.
Figure 14. Dust hose attached to dust port set-
up for jointer operations.
-16-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Rotate the cutterhead pulley until one of the
knives is at top dead center (TDC), as shown
in Figure 17.
Setting Outfeed
Table Height
Top Dead
Center
The outfeed table height MUST be level with the
knives when they are at top-dead-center. If the
outfeed table is set too low, the workpiece will be
tapered. If the outfeed table is set too high, the
workpiece will hit the edge of the outfeed table
during operation, increasing the chance of kick-
back.
Figure 17. Cutterhead knife at top-dead-center.
To set the outfeed table height:
7. When the outfeed table is correctly set, the
knife will just touch the gauge when the knife
is at its highest point of rotation (Figure 18).
When the cutterhead pulley is rotated, the
1. DISCONNECT THE JOINTER/PLANER
FROM THE POWER SOURCE!
1
2. Move the blade guard out of the way or
gauge should move ⁄8" toward the infeed
remove it.
table and the inward mark should be directly
over the edge of the outfeed table ( Figure
18).
3. Secure the outfeed table with the outfeed
table lock.
Inward Mark
4. Remove the front access panel (see
Replacing Flat Drive Belt, Steps 3-4 on
Page 33) to access the cutterhead pulley.
1
5. Place the knife setting gauge on the front of
the outfeed table so the gauge extends over
the cutterhead and the outward mark is at the
edge of the outfeed table (Figure 16).
⁄8
"
Outfeed
Infeed
Outward Mark
Figure 18. Knife gauge positioned over
cutterhead knife.
—If your outfeed table is correctly set, no
adjustments are necessary.
Outfeed
Infeed
—If the knife lifts the gauge off the table or
the table is below the gauge, continue to
Checking Outfeed Table Parallelism on
Page 39 in the SERVICE section.
Figure 16. Knife gauge positioned over
cutterhead knife.
8. Reinstall the front access panel and blade
guard.
-17-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
—If the cutterhead does not rotate, the
cutterhead safety switch is working cor-
rectly. Continue to Step 10.
Test Run
Once the assembly is complete, test run your
machine to make sure it runs properly.
— If the cutterhead rotates, immediately stop
the machine and DISCONNECT THE
JOINTER/PLANER FROM THE POWER
SOURCE! The safety switch is not work-
ing correctly. This safety feature must work
properly before proceeding with regular
operations. Call Tech Support for help.
The test run consists of verifying the following: 1)
The motor powers up and runs correctly, and 2)
the cutterhead safety switch works correctly.
If, during the test run, you cannot easily locate
the source of an unusual noise or vibration, stop
using the machine immediately, then review the
Troubleshooting on Page 37.
10. Set the machine up for planer operations.
Refer to Planer Operation Setup, Steps 1-5
on Page 22, for detailed instructions.
If you still cannot remedy a problem, contact our
Tech Support at (570) 546-9663 for assistance.
11. Swing the dust chute assembly clockwise
over the cutterhead and rest the catch lever
on the infeed table, as shown in Figure 19.
To test run the machine:
1. Make sure you have read the safety instruc-
tions at the beginning of the manual and you
have performed the assembly instructions.
2. Make sure all tools and objects used during
setup are cleared away from the machine.
3. Push the outfeed table lock lever down.
4. Connect the machine to the power source.
Figure 19. Dust chute catch disengaged.
12. Turn the machine ON.
5. Open the switch cover and press the green
ON button to turn the machine ON.
6. Listen to and watch for abnormal noises or
actions. The machine should run smoothly
with little or no vibration or rubbing noises.
—If the cutterhead does not rotate, the
cutterhead safety switch is working cor-
rectly. The test run is complete.
—Investigate and correct strange or unusual
noises or vibrations before operating the
machine further. Always disconnect the
machine from power when investigating or
correcting potential problems.
—If the cutterhead rotates, immediately stop
the machine and DISCONNECT THE
JOINTER/PLANER FROM THE POWER
SOURCE! The safety switch is not work-
ing correctly. This safety feature must work
properly before proceeding with regular
operations. Call Tech Support for help.
7. Turn the machine OFF.
8. Move the fence all the way back and com-
pletely cover the cutterhead with the blade
guard.
13. To finish setting up the machine for planer
operation, push the dust chute down until
you hear a "click," indicating the dust chute is
locked, then connect the dust hose.
9. Disengage the outfeed table lock lever, lift the
outfeed table up about an inch or until you
hear a "click" then turn the machine ON.
14. To convert the machine to a jointer, follow the
Jointer Operation Setup on Page 23.
-18-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Recommended
Adjustments
Belt Break-In
The final step in the setup process must be done
after approximately three hours of operation.
During this first three hours, the belts will stretch
and seat into the pulley grooves. After this, you
must re-tension the belts to avoid slippage and
burn out. Refer to Page 32 when you are ready to
perform this important adjustment.
For your convenience, the adjustments listed
below have been performed at the factory and
no further setup is required to operate your
machine.
However, because of the many variables involved
with shipping and storage, some of these adjust-
ments may need to be repeated to ensure opti-
mum cutting results. Keep this in mind as you
start to use your new jointer/planer.
Note: Pulleys and belts can get hot. This is a nor-
mal condition. Allow them to cool before making
adjustments.
Step-by-step instructions for these adjust-
ments can be found in SECTION 7: SERVICE
ADJUSTMENTS.
Factory adjustments that should be verified:
1. Cutterhead Knife Height (Page 42)
2. Fence Stop Accuracy (Page 44)
3. Feed Roller Spring Tension (Page 46)
4. Jointer-Table Parallelism (Page 39)
-19-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: OPERATIONS
Basic Jointer
To reduce the risk of
serious injury when using
this machine, read and
Controls
understand this entire
This section covers the controls used during
manual before beginning
routine jointer operations. To use the machine
any operations.
as a planer, you must perform a conversion (see
Jointer-Planer Conversion on Page 22).
ON/OFF Button (Figure 20): Starts or stops
motor when pushed in.
Damage to your eyes, lungs, and ears could
result from using this machine without
proper protective gear. Always wear safety
glasses, a respirator, and hearing protection
when operating this machine.
On
Button
Off Button
Loose hair, clothing, or
jewelry could get caught
in machinery and cause
serious personal injury.
Keep these items away
from moving parts at all
times to reduce this risk.
Figure 20. ON/OFF button locations.
Table Movement: Raise or lower the infeed table
adjustment lever (Figure 21) to control how much
stock is removed by the cutterhead.
Fence Lock
Scale
NOTICE
If you have never used this type of machine
or equipment before, WE STRONGLY REC-
OMMEND that you read books, trade maga-
zines, or get formal training before begin-
ning any projects. Regardless of the con-
tent in this section, Grizzly Industrial will
not be held liable for accidents caused by
lack of training.
Outfeed Table
Lock
Infeed Table
Adjustment
Lever
Figure 21. Fence and table height controls.
-20-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
To unlock the outfeed table, raise the outfeed
table lock lever. To lock the outfeed table, lower
the outfeed table, then engage the lock lever.
Fence Movement: The fence lock keeps the
fence in position (Figure 21). To move the fence,
loosen the fence lock, slide the fence to the
desired position, then secure the lock.
Fence Tilting: The tilt locks (Figure 22) secure
the fence at any position in the available range.
Fence stops set the fence at 90° or 45° outward.
The tilt locks must be tightened before cutting.
See Page 44 for more detail on setting the fence
stops.
Bevel
Figure 23. Fence bevel flush with table at 45°.
Blade Guard: To position the blade guard over
the cutterhead (Figure 24), loosen the lock knob,
reposition the guard, then tighten the lock knob.
Place the guard as close as possible to the
cutterhead during operations to reduce the risk of
serious injury from cutterhead contact—while also
allowing adequate clearance for workpieces.
Fence Height
Knobs
Angle Scale
Lock Knob
Tilt
Locks
Adjustment
Knob
Figure 22. Fence tilt controls.
To move the fence to 45° outward, loosen the tilt
locks and fence height knobs, move the blade
guard away from the fence several inches, and
move the fence bevel flush against the table (see
Figure 23). Verify the angle with a 45° square,
then tighten the height knobs and tilt locks.
Lock Lever
Figure 24. Blade guard controls.
To return the fence to the 90° position, loosen the
tilt locks and height knobs, raise the fence to 90°.
Check the fence angle with a 90° square, making
sure the fence and table are flush, then tighten the
height knobs and tilt locks.
Blade Guard Arm: To adjust the blade guard
height, turn the adjustment knob (see Figure 24)
clockwise to lower and counterclockwise to raise
the blade guard. To move the bracket and blade
guard out of the way, disengage the lock lever,
then rotate the bracket assembly away from the
outfeed table.
-21-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Planer
Controls
Jointer-Planer
Conversion
This section covers the controls used during rou-
tine planer operations.
The Model G0675 is ready for jointer operations
after it is setup. To use the machine as a planer,
you must perform a conversion.
See Page 20 for a description of the ON/OFF
switch.
Planer Operation Setup
Table Height Handwheel: To raise or lower the
planer table, rotate the table height handwheel
(Figure 25).
1. DISCONNECT THE JOINTER/PLANER
FROM THE POWER SOURCE!
Table Height Scale: Read the depth-of-cut from
the inch scale.
2. Loosen the fence lock lever, then remove the
fence.
3. Engage the blade guard lock knob and blade
guard arm lock lever (see Figure 24 on Page
21).
4. Disengage the outfeed table lock lever, and
raise the table up all the way so the pin seats
into the groove on the lock arm (Figure 26).
Table Height
Scale
Table Height
Handwheel
Figure 25. Planer table control locations.
Figure 26. Outfeed table lock arm.
Serious personal injury could occur if you
place your fingers between the table and
base or between pivot points. Your hands
could be pinched or crushed!
5. Remove the dust hose from the jointer dust
port, then remove the dust port.
6. Use the table height handwheel to lower the
planer table to approximately the 6" mark.
-22-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Swing the dust chute assembly clockwise
over the cutterhead, then push it down onto
the infeed table until you hear a "click"—this
indicates that the lock lever (Figure 27) has
secured the infeed table. The lever must
engage the infeed table for the planer to
operate.
Jointer Operation Setup
1. Reverse Steps 2–8 in the previous subsec-
tion. You must push the catch lever back to
release the dust port.
2. While holding the outfeed table up, push
the lock arm pin out to fold the lock arm in
and lower the outfeed table most of the way
(Figure 26). When the table is close to the
frame, raise the outfeed table lock lever,
lower the table the rest of the way, then push
the lever down to secure the outfeed table.
Dust Port
Thumb Knob
3. Re-install the fence.
Lock
Lever
Figure 27. Dust chute secured.
The dust chute must be secured during
planer operations or the machine will not
operate. If the machine DOES operate when
the dust chute lock is disengaged, immedi-
ately DISCONNECT THE JOINTER/PLANER
FROM POWER and call Technical Support.
8. Install the dust port onto the dust chute with
the thumb knob, as shown in Figure 27, then
install the dust hose with a hose clamp.
-23-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Stock Inspection
and Requirements
CORRECT
Here are some rules to follow when choos-
ing stock for the jointer/planer:
With Grain
INCORRECT
•
DO NOT joint or surface plane stock that
contains knots. Injury to the operator or
damage to the workpiece can occur if the
knots become dislodged during the cutting
operation.
Against Grain
Figure 29. Correct and incorrect grain alignment
•
•
DO NOT joint or surface plane against the
grain direction. Cutting against the grain
increases the likelihood of stock kickback, as
well as tear-out on the workpiece.
to cutterhead (planer).
•
Remove foreign objects from the stock.
Make sure that any stock you process with
the jointer/planer is clean and free of any dirt,
nails, staples, tiny rocks or any other foreign
objects, which if they hit the knives and are
drawn into the dust collector, may cause a
fire hazard. The particles may also damage
the knives. Wood stacked on a concrete floor
can have small pieces of stone or concrete
pressed into the surface.
Jointing and surface planing with the
grain produces a better finish and is safer
for the operator. Cutting with the grain is
described as feeding the stock so the grain
points down and toward you on the jointer
(Figure 28) or away from you on the planer
(Figure 29), as viewed from the edge.
Note: If the grain changes direction along the
edge of the board, decrease the cutting depth
and make additional passes.
•
•
Only process natural wood fiber through
your jointer/planer. Never joint MDF, par-
ticle board, plywood, laminates or other syn-
thetically made materials.
CORRECT
Make sure all stock is sufficiently dried
before jointing or planing. Wood with a
moisture content over 20% will cause unnec-
essary wear on the knives and poor cutting
results. Excess moisture can also hasten rust
and corrosion.
With Grain
INCORRECT
•
•
Scrape all glue off of boards before plan-
ing.
Keep your work area clear.
Against Grain
Figure 28. Correct and incorrect grain alignment
to cutterhead (jointer).
-24-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Jointer Specific Rules:
Squaring Stock
•
Make sure your workpiece exceeds
the minimum dimension requirements
(Figures 30 & 31) before edge jointing or
surface planing, or it may break or kick
back during the operation!
Squaring stock involves four steps performed
in the order below:
1. Surface Plane on the Jointer—The con-
cave face of the workpiece is surface planed
flat with a jointer.
12" Min.
12" Min.
1
1" Min.
⁄2" Min.
1
⁄2" Min.
1" Min.
2. Surface Plane on the Thickness Planer—
The opposite face of the workpiece is surface
planed flat with a thickness planer.
Figure 30. Minimum dimensions for edge jointing
and surface planing (jointer).
Thickness Planer Specific Rules:
•
Use the full width of the planer. Alternate
between the left, the right, and the middle
when feeding narrow lumber into the planer.
Your knives will remain sharp much longer.
Previously
Surface
Planed Face
3. Edge Joint on the Jointer—The concave
edge of the workpiece is jointed flat with a
jointer.
12" Min.
1
⁄4" Min.
1" Min.
Figure 31. Minimum dimensions for surface
4. Rip Cut on a Table Saw—The jointed edge
of the workpiece is placed against a table
saw fence and the opposite edge cut off.
planing (thickness planer).
Previously
Jointed Edge
-25-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Adjust the blade guard for the workpiece
Surface Planing
thickness.
—If the workpiece is less than or equal to 3"
thick, adjust the guard so it touches the
fence and is just above the workpiece—
allowing the workpiece to move freely (see
Figure 33). Tighten the blade guard lock
knob.
The purpose of surface planing on the jointer is
to make one flat face on a piece of stock (see
Figures 32–34) to prepare it for thickness planing
on the planer.
NOTICE
If you are not experienced with a jointer,
set the depth of cut to 0", and practice
feeding the workpiece across the tables as
described. This procedure will better pre-
pare you for the actual operation.
Figure 33. Surface planing board less than 3"
thick.
—If the workpiece is greater than 3" thick,
adjust the blade guard 3⁄8" to 1⁄2" away from
the workpiece (see Figure 34), lower the
3
guard to its lowest position (about ⁄4" over
the cutterhead) then tighten the blade
guard lock knob.
Figure 32. Illustration of surface planing results.
To surface plane on the jointer:
3
⁄
8"-1⁄2
"
1. Read and understand SECTION 1: SAFETY,
beginning on Page 6.
2. Make sure your stock has been inspected
for dangerous conditions as described in the
Stock Inspection & Requirements instruc-
tions, beginning on Page 24.
3. Set the cutting depth for your operation. (We
suggest 1⁄32" for surface planing, using a more
shallow depth for hard wood species or for
wide stock.)
Figure 34. Surface planing stock greater than 3"
4. Make sure your fence is set to 90˚.
thick.
-26-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: If your leading hand (with push block)
gets within 4" of the cutterhead, lift it up and
over the cutterhead, and place the push
block on the portion of the workpiece that is
on the outfeed table. Now, focus your pres-
sure on the outfeed end of the workpiece
while feeding, and repeat the same action
with your trailing hand when it gets within 4"
of the cutterhead. To keep your hands safe,
DO NOT let them get closer than 4" from the
cutterhead when it is moving!
Failure to use push blocks when surface
planing may result in cutterhead contact,
which will cause serious personal injury.
Always use push blocks to protect your
hands when surface planing on the jointer.
6. If your workpiece is cupped (warped), place
it so the concave side is face down on the
surface of the infeed table.
9. Repeat Step 8 until the entire surface is flat.
7. Start the jointer.
8. With a push block in each hand, press the
workpiece against the table and fence with
firm pressure, and feed the workpiece over
the cutterhead.
-27-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
To edge joint on the jointer:
Edge Jointing
1. Read and understand SECTION 1: SAFETY,
beginning on Page 6.
The purpose of edge jointing is to produce a fin-
ished, flat-edged surface (see Figures 35 & 36)
that is suitable for joinery or finishing. It is also a
necessary step when squaring rough or warped
stock.
2. Make sure your stock has been inspected
for dangerous conditions as described in the
Stock Inspection & Requirements instruc-
tions, beginning on Page 24.
3. Set the cutting depth for your operation. (We
1
1
suggest between ⁄16" and ⁄8" for edge joint-
ing, using a more shallow depth for hard
wood species or for wide stock.)
NOTICE
If you are not experienced with a jointer,
set the depth of cut to 0", and practice
feeding the workpiece across the tables as
described below. This procedure will better
prepare you for the actual operation.
4. Make sure the fence is set to 90˚, adjust
3
1
the blade guard ⁄8" to ⁄2" away from the
workpiece (see Figure 35), then tighten the
blade guard lock knob.
3
⁄
8"-1⁄2
"
5. If your workpiece is cupped (warped), place
it so the concave side is face down on the
surface of the infeed table.
6. Start the jointer.
7. Press the workpiece against the table and
fence with firm pressure. Use your trailing
hand to guide the workpiece through the cut,
and feed the workpiece over the cutterhead.
Note: If your leading hand gets within 4"
of the cutterhead, lift it up and over the
cutterhead, and place it on the portion of
the workpiece that is over the outfeed table.
Now, focus your pressure on the outfeed end
of the workpiece while feeding, and repeat
the same action with your trailing hand when
it gets within 4" of the cutterhead. To keep
your hands safe, DO NOT let them get closer
than 4" from the cutterhead when it is mov-
ing!
Figure 35. Edge jointing operation.
8. Repeat Step 7 until the entire edge is flat.
Figure 36. Illustration of edge jointing results.
-28-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
To bevel cut on the jointer:
Bevel Cutting
1. Read and understand SECTION 1: SAFETY,
beginning on Page 6.
The purpose of bevel cutting is to cut a specific
angle into the edge of a workpiece (see Figures
37 & 38).
2. Make sure your stock has been inspected
for dangerous conditions as described in the
Stock Inspection & Requirements instruc-
tions, beginning on Page 24.
The Model G0675 has preset fence stops at 45˚
outward and 90˚. If your situation requires a dif-
ferent angle, the preset fence stops can be easily
adjusted for your needs.
3. Set the cutting depth for your operation. (We
1
1
suggest between ⁄16" and ⁄8" for bevel cut-
ting, using a more shallow depth for hard
wood species or for wide stock.)
NOTICE
4. Make sure your fence is set to the angle of
If you are not experienced with a jointer,
set the depth of cut to 0", and practice
feeding the workpiece across the tables as
described below. This procedure will better
prepare you for the actual operation.
3
your desired cut, adjust the blade guard ⁄8
"
1
to ⁄2" away from the workpiece (see Figure
37), then tighten the blade guard lock knob.
5. If your workpiece is cupped (warped), place
it so the concave side is face down on the
surface of the infeed table.
3
⁄
8"-1⁄2
"
6. Start the jointer.
7. With a push block in your leading hand, press
the workpiece against the table and fence
with firm pressure, and feed the workpiece
over the cutterhead.
Note: If your leading hand gets within 4"
of the cutterhead, lift it up and over the
cutterhead, and place the push block on
the portion of the workpiece that is on the
outfeed table. Now, focus your pressure on
the outfeed end of the workpiece while feed-
ing, and repeat the same action with your
trailing hand when it gets within 4" of the
cutterhead. To keep your hands safe, DO
NOT let them get closer than 4" from the
cutterhead when it is moving!
Figure 37. Bevel cutting operation.
8. Repeat Step 7 until the angled cut is satis-
factory to your needs.
Figure 38. Illustration of bevel cutting results.
-29-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
—If the cut is too heavy and bogs down the
planer, turn the planer OFF immediately,
allow it to come to a complete stop, remove
the workpiece, and repeat Steps 3–5.
Thickness Planer
Operation
6. Support the workpiece as it leaves the outfeed
The Model G0675 planer table moves approxi-
mately ⁄16" with one full turn of the handwheel.
end of the planer to reduce snipe.
1
Each graduated mark on the table height
handwheel represents 0.001" movement.
7. Measure your workpiece thickness and adjust
the table height as necessary to take a lighter
or heavier pass, depending on your needs.
For most wood types, 1⁄16" per pass is a good
cutting depth.
To use the planer:
1. Put on safety glasses.
Note: Any time you switch directions with the
table height handwheel, there will be a small
amount of backlash—so the first crank of the
handwheel after switching directions will be
2. Unless your workpiece is very flat, surface
plane the workpiece on the jointer until it is
flat—having the face flat will ensure that it
sits flat on the planer table during operation.
1
slightly less than ⁄16". However, as long as
you move the handwheel in the same direc-
tion during operation, backlash will not be a
factor.
3. Adjust the table height to slightly lower than
your workpiece height to ensure the first
cut is as light as possible (approximately
1⁄32"–1⁄16") .
4. Start the planer.
5. Place the flat side of the board down on the
table (on the left side, facing the front of the
machine), and feed the workpiece through
the planer—in the opposite direction as when
jointing (see Figure 39). Make sure not to
stand directly in front or behind the workpiece
to avoid kickback injury.
Figure 39. Planer operation.
-30-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
SECTION 5: ACCESSORIES
G5562—SLIPIT® 1 Qt. Gel
G9643—8" Precision Straightedge
G9644—12" Precision Straightedge
H2675—16" Precision Straightedge
Idealforaligningyouroutfeedbedtothecutterhead
and calibrating your depth scale. These grade
00 heavy-duty stainless steel straightedges are
manufactured to DIN874 standards for profes-
sional results in set-up and inspection work.
G5563—SLIPIT® 12 oz Spray
G2871—Boeshield® T-9 12 oz Spray
G2870—Boeshield® T-9 4 oz Spray
H3788—G96® Gun Treatment 12 oz Spray
H3789—G96® Gun Treatment 4.5 oz Spray
Figure 40. Recommended products for protect-
ing unpainted cast iron/steel parts on machinery.
Figure 42. Straightedges.
G1738—Rotacator™ Precision Planer Tool
The Rotacator is a dial indicator on a magnetic
base and is designed for quickly and accurately
setting the critical tolerances needed when adjust-
ing any planer, so that nasty surprises such as
non-parallel and chattered cuts can be eliminated.
A great setup tool for other machines! Accurate to
0.001". Indicator rotates 360˚.
T20501—Face Shield Crown Protector 4"
T20502—Face Shield Crown Protector 7"
T20503—Face Shield Window
T20451—"Kirova" Clear Safety Glasses
T20452—"Kirova" Anti-Reflective Glasses
H7194—Bifocal Safety Glasses 1.5
H7195—Bifocal Safety Glasses 2.0
H7196—Bifocal Safety Glasses 2.5
T20502
T20452
T20503
T20451
H7194
Figure 41. Rotacator™ Precision Planer Tool.
Figure 43. Our most popular eye protection.
-31-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: MAINTENANCE
Note: This maintenance schedule is based on
average usage. Adjust the maintenance schedule
to match your usage to keep your jointer/planer
running smoothly and to protect your investment.
Always disconnect power
to the machine before
performing maintenance.
Failure to do this may
result in serious person-
al injury.
Cleaning
Vacuum excess wood chips and sawdust, and
wipe off the remaining dust with a dry cloth—this
ensures moisture from wood dust does not remain
on bare metal surfaces. Treat all unpainted cast
Schedule
For optimum performance from your machine, fol-
low this maintenance schedule and refer to any
specific instructions given in this section.
iron and steel with a non-staining lubricant after
cleaning. We recommend products like SLIPIT®,
G96® Gun Treatment, or Boeshield® T-9 (see
Page 31 for more details).
First 3–5 Hours of Operation
•
Re-tension belts.
•
Lubricate elevation lead screws (Page 35).
Belts
Daily Check:
•
Clean unpainted cast iron parts of jointer and
V-belt and flat belt removal and replacement
involves removing the belts, rolling them off of
the pulleys, replacing them with new belts, then
re-tensioning them.
planer tables.
Clean cutterhead.
•
Every 20 Hours of Operation
Lubricate elevation lead screws (Page 35).
•
Always replace the belts simultaneously, or belt
tension may not be even among the belts and
may cause premature belt failure.
Every 40 Hours of Operation
•
Check and re-tension belts (on this page).
Lubricate cogwheels (Page 35).
•
After the first three hours of operation, re-tension
the belts, as they will stretch and seat during this
time. Then check and re-tension if necessary
after 40 operating hours.
Monthly Check:
•
Lubricate feed roller chain and feed roller
sprockets (Page 35).
•
•
Lubricate fence (Page 34).
Lubricate outfeed table lock arm and pivot
points (Page 36).
Clean/vacuum dust inside planer cabinet.
Lubricate blade guard arm (Page 35).
Tools Needed
Wrenches 10 & 13mm..................................1 Ea
Hex Wrenches 5 & 6mm ..............................1 Ea
Qty
•
•
Replacing Flat Drive Belt
1. DISCONNECT THE JOINTER/PLANER
Semi-Anually
Lubricate table height chain and planer
handwheel linkage (Page 36).
•
FROM THE POWER SOURCE!
2. Raise the planer table to about the 6" mark.
Annually
•
Lubricate table height chain and planer
handwheel (Page 36).
-32-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Remove the four cap screws (Figure 44)
inside the cabinet on the fence side, then
remove the rear access panel.
6. Squeeze the flat belt in the middle to remove
tension, then tighten the locking nut nearby to
hold the drive pulley.
7. Remove the flat belt and install the new flat
drive belt onto the pulleys.
8. Loosen the locking nut to lower the drive pul-
ley.
Cap Screws
9. Tighten both locking nuts and push the flat
belt in the center to check belt tension.
The belt is correctly tensioned when there
is approximately ⁄2" deflection when the flat
Front View
1
Rear View
drive belt is pushed with moderate pres-
sure, as shown in Figure 47. Continue to
Adjusting /Replacing Feed Cylinder Belts.
Figure 44. Location of rear access panel screws.
4. Repeat Step 3 to remove the front access
panel.
Pulley
5. Loosen the locking nuts on both sides of the
machine, as shown in Figures 45 & 46.
1
⁄
2
"
Flat Drive Belt
Deflection
Pulley
Motor
Pulley
Locking Nut
Figure 47. Checking belt tension.
Figure 45. Location of locking nut on rear of
—If there is more than 1⁄2" deflection when the
flat belt is pushed with moderate pressure,
loosen the locking nuts, adjust the motor
pulley downward, then tighten the locking
nuts. Continue to Adjusting/Replacing
Feed Cylinder Belts.
machine.
Adjusting/Replacing Feed Belts
Locking Nut
1. DISCONNECT THE JOINTER/PLANER
FROM THE POWER SOURCE!
2. Raise the planer table to the 3" mark, remove
the four cap screws that secure the front
access panel, then remove the panel.
Figure 46. Location of locking nut on front of
machine.
-33-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Loosen the four cap screws on the wheel
bracket, and one cap screw on the infeed belt
wheel (see Figure 48), then raise the infeed
belt wheel.
Lubrication
An essential step for lubrication is cleaning the
components before lubricating them.
Wheel Bracket
This idea is critical because dust and chips build
up on lubricated components and make the
components hard to move. Simply adding more
grease to the components with built-up grime on
them will not yield smooth moving components.
Infeed
Belt
Wheel
Flat Belt
Clean the components in this section with an oil/
grease soluble cleaner, such as mineral spirits.
The following are the main components that need
to be lubricated:
V-belt
•
•
•
•
Fence (on this page)
Blade Guard Arm (Page 35)
Leadscrews (Page 35)
Feed Roller Chain, Sprocket and Cogwheels
(Page 35)
Outfeed Table (Page 36)
Table Height Chain (Page 36)
Planer Table Handwheel (Page 36)
Figure 48. Cap screw locations.
4. Remove the flat belt and V-belt, install a new
flat belt and V-belt in the same manner that
you removed them.
•
•
•
5. Push the wheel bracket (see Figure 48)
down and tighten the four cap screws, then
push the infeed belt wheel down and tighten
the cap screw loosened in Step 3.
Schedules are based on average use. Adjust
lubrication according to your level of use.
6. Check the tension of each belt.
Fence
1
—If there is approximately ⁄2" deflection
Clean away any built up grime and debris with
a rag and mineral spirits, then place 1-2 drops
of light machine oil on the pivot points shown in
Figure 49 once a month. Move the fence through
its full range of motion to distribute the oil.
when the flat belt or V-belt is pushed with
moderate pressure, the belts are correctly
tensioned.
—If there is more than 1⁄2" deflection when the
flat belt or V-belt is pushed with moderate
pressure, repeat Steps 3–5, then check
the tension again.
7. Re-install the front and rear access panels
with the cap screws you removed earlier.
Figure 49. Fence lubrication locations.
-34-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Guard Arm
Clean away any built up grime and debris with a
rag and mineral spirits, then place 1-2 drops of
light machine oil on the points shown in Figure
50 once a month.
Figure 52. Additional leadscrew lubrication
locations.
Feed Roller Chain, Sprocket and
Cogwheels
Inspect the feed roller chain and feed roller
sprockets monthly. Thoroughly clean debris and
grime with a rag and mineral spirits, then use a
brush or rag to apply a thin coat of multi-purpose
grease when needed, as shown in Figure 53.
Remove the front panel to access.
Figure 50. Blade guard arm lubrication locations.
Leadscrews
Lubricate the cogwheels with a thin coat of multi-
purpose grease every 40 operating hours.
Clean away debris and built-up grime on the lead-
screws with a rag and mineral spirits, then apply a
thin coat of SAE 10-30W oil with a clean rag to the
four leadscrews in the locations shown in Figures
51–52 after the first five hours and then every 20
hours. Move the planer table through its full range
of motion to distribute the lubricant.
Feed
Roller
Chain
Sprocket
Cogwheels
Figure 53. Feed roller chain, sprocket, and
cogwheel lubrication locations.
Figure 51. Leadscrew-planer table lubrication
locations.
-35-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
To access the table height chain and planer table
handwheel linkage, remove the fence, front and
rear access panels, blade guard arm assembly,
and rear fence rail. With the help of an assis-
tant, lift the machine off the base, then turn the
machine over and place it upside down on blocks,
carpet, or cardboard (see Figure 56).
Outfeed Table
Clean debris and grime from the outfeed table
lock arm and pivot points, then apply 1-2 drops
of light machine oil to the components shown in
Figure 54 once a month.
Figure 54. Outfeed table lubrication points.
Figure 56. Machine turned over for access to
Table Height Chain & Planer
Handwheel
table height chain.
Inspect the table height chain (see Figure 55)
every six months to a year. Clean away debris and
built-up grime on the chain with a rag and mineral
spirits, then apply a thin coat of multi-purpose
grease. Lubricate the planer table handwheel link-
age with light machine oil as needed.
After lubricating the chain and handwheel mecha-
nism, make sure the outfeed table is locked, then
reverse the prior steps to reassemble the jointer/
planer.
Handwheel
Linkage
Table Height
Chain
Figure 55. Table height chain and handwheel
linkage.
-36-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7: SERVICE
Review the troubleshooting and procedures in this section to fix or adjust your machine if a problem devel-
ops. If you need replacement parts or you are unsure of your repair skills, then feel free to call our Technical
Support at (570) 546-9663.
Troubleshooting
Symptom
Possible Cause
Possible Solution
Machine does not
start or a breaker
trips.
1. Blown fuse.
1. Replace fuse/ensure no shorts.
2. Ensure power supply is on/has correct voltage.
3. Test for good contacts; correct the wiring.
4. Test/replace if faulty.
2. Power supply switched OFF or at fault.
3. Plug/receptacle at fault/wired wrong.
4. Start capacitor at fault.
5. Wall circuit breaker tripped.
6. Wiring open/has high resistance.
7. Motor ON/OFF switch at fault.
8. Motor at fault.
5. Ensure circuit size is correct/replace weak breaker.
6. Check/fix broken, disconnected, or corroded wires.
7. Replace switch.
8. Test/repair/replace.
9. Dust chute lock not engaged on infeed table 9. Engage the dust chute lock (planer); lock the outfeed
(planer operation); outfeed table unlocked
and raised up (jointer operation).
table down (jointer).
Machine stalls or is 1. Feed rate/cutting speed too fast.
underpowered.
1. Decrease feed rate/cutting speed.
2. Workpiece material not suitable for 2. Only cut wood/ensure moisture is below 20%.
machine.
3. Machine undersized for task.
4. Belt(s) slipping.
3. Use correct blade/reduce feed rate or depth of cut.
4. Tension/replace belt(s); ensure pulleys are aligned.
5. Wire motor correctly.
5. Motor wired incorrectly.
6. Plug/receptacle at fault.
7. Pulley/sprocket slipping on shaft.
8. Motor bearings at fault.
9. Machine undersized for task.
10. Motor overheated.
6. Test for good contacts/correct wiring.
7. Replace loose pulley/shaft.
8. Test/repair/replace.
9. Use sharp knives; reduce feed rate/depth of cut.
10. Clean motor, let cool, and reduce workload.
11. Test/repair/replace.
11. Motor at fault.
Machine has
vibration or noisy
operation.
1. Motor or component loose.
1. Inspect/replace damaged bolts/nuts, and re-tighten
with thread locking fluid.
2. Knives/gibs at fault.
2. Resharpen/replace knives; set knife alignment/
height correctly.
3. Blade at fault.
3. Replace warped/bent blade; resharpen dull blade.
4. Inspect/replace belts with a new matched set.
5. Realign/replace shaft, pulley, setscrew, and key.
6. Tighten/replace.
4. Belts worn or loose.
5. Pulley loose.
6. Motor mount loose/broken.
7. Machine incorrectly mounted.
8. Motor fan rubbing on fan cover.
9. Motor bearings at fault.
7. Tighten mounting bolts; relocate/shim machine.
8. Fix/replace fan cover; replace loose/damaged fan.
9. Test by rotating shaft; rotational grinding/loose shaft
requires bearing replacement.
10. Cutterhead bearings at fault.
10. Replace bearing(s)/realign cutterhead.
-37-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Possible Cause
Possible Solution
1. Table lock lever engaged when table is 1. Disengage table lock lever, lower table, then engage
Outfeed table does
not lock.
being closed.
lever.
1. Table lock arm stuck.
1. Push lock arm pin out; lubricate as needed.
Outfeed table will
not close.
Excessive
snipe 1. Operator pushing down on trailing end of 1. Lift up on the trailing end of the workpiece as it
(gouge in the end
of the board that is
uneven with the rest
of the cut).
workpiece.
enters and leaves the planer.
2. Workpiece is not supported as it leaves the 2. Support the workpiece as it leaves the outfeed end
planer.
of the planer.
Workpiece stops/ 1. Taking too heavy of a cut.
1. Take a lighter cut.
slows in the middle
of the cut.
2. Pitch and glue build up on planer 2. Clean the internal cutterhead components with a
components.
pitch/resin dissolving solvent.
Workpiece feeds 1. Rubber lining on rubber feed rollers has 1. Replace feed rollers (Page 47).
erratically.
eroded excessively.
Chipping (consistent 1. Knots or conflicting grain direction in wood. 1. Inspect workpiece for knots and grain direction; only
pattern).
use clean stock.
2. Nicked or chipped knife.
3. Taking too deep of a cut.
2. Replace the knife (Page 43).
3. Take a smaller depth of cut. (Always reduce cutting
depth when surface planing or working with hard
woods.)
Fuzzy grain.
1. Wood may have high moisture content or 1. Check moisture content and allow to dry if moisture
surface wetness.
2. Dull knives.
is too high.
2. Replace the knives (Page 43).
Long lines or ridges 1. Nicked or chipped knives.
that run along the
1. Replace knives (Page 43).
length of the board
Uneven knife marks, 1. Knives not adjusted at even heights in the 1. Adjust the knives so they are set up evenly in the
wavy
surface,
cutterhead.
cutterhead (Page 43).
or chatter marks
across the face of
the board.
2. Worn cutterhead bearings.
2. Replace cutterhead bearings.
Glossy
(Planer)
surface. 1. Knives are dull.
1. Replace the knives (Page 43).
2. Cutting depth too shallow.
2. Increase the depth of cut.
Chip Marks
(inconsistent
pattern). (Planer)
1. Chips aren't being properly expelled from 1. Use a dust collection system.
the cutterhead.
Board
edge
is 1. Board not held with even pressure on infeed 1. Hold board with even pressure as it moves over the
concave or convex
and outfeed table during cut.
2. Board started too uneven.
cutterhead.
after
jointing.
2. Take partial cuts to remove the extreme high spots
before doing a full pass.
(Jointer)
3. Board has excessive bow or twist along its 3. Surface plane one face so there is a good surface to
length.
position against the fence.
4. Insufficient number of passes.
4. It may take 3 to 5 passes to achieve a perfect edge,
depending on starting condition of board and depth
of cut.
-38-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Tools Needed
Qty
Jointer Table
Parallelism
Straightedge ...................................................... 1
Hex Wrench 5mm ............................................. 1
Wrench 13mm ................................................... 1
Feeler Gauge Set.............................................. 1
Assistant............................................................ 1
The tables of your jointer MUST be parallel with
the cutterhead and each other (see Figure 57) to
reduce the risk of workpiece kickback and to help
ensure good cutting results.
Checking Outfeed Table Parallelism
The outfeed table is preset by the factory parallel
with the cutterhead. However, it is critical to check
this setting.
To check outfeed table parallelism:
1. DISCONNECT THE JOINTER/PLANER
FROM THE POWER SOURCE!
2. Remove the blade guard arm assembly.
Black Lines Represent
Straightedge Positions
From Overhead View
3. Place the straightedge on the back of the
outfeed table so it hangs over the cutterhead
as shown in Figure 58.
Figure 57. Illustration of table parallelism
concept.
Black Lines Represent
Straightedge Positions
From Overhead View
Adjusting the tables parallel with each other is
a complex and precise task that may take more
than an hour to complete.
Back
Due to the complex nature of this task, we rec-
ommend that you double check the current table
positions to make sure that they really need to be
adjusted before starting.
Front
Note: Typically, a tolerance of 0.005" in parallel-
ism between the tables is considered acceptable.
Figure 58. Straightedge positions for verifying if
the outfeed table is parallel with the cutterhead.
When adjusting table parallelism, you must do
the following: 1) properly adjust the outfeed
table height and parallelism in relation to the
cutterhead, and 2) adjust the infeed table parallel
to the outfeed table, and 3) adjust the knives to
bring the outfeed table surface and cutting edges
of the knives to the same height.
4. Try to fit a 0.060" feeler gauge (or combina-
tion of feeler gauges) between the cutterhead
body and the bottom of the straightedge
(Figure 59).
Note: Rotate the cutterhead to make sure the
knives do not interfere with proper measure-
ment.
-39-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: The back side of the outfeed table is
factory set approximately 0.060" from the
cutterhead. The back side of the outfeed
table is not adjustable, so any adjustments to
parallelism must be made on the front of the
outfeed table.
Correcting Outfeed Table to
Cutterhead Parallelism
This procedure involves loosening the outfeed
table support blocks and adjusting their height to
raise or lower the front of the outfeed table until it
is parallel with the cutterhead.
To correct outfeed table parallelism:
1. Loosen the cap screws on both outfeed table
support blocks (see Figure 60).
0.060"
Straightedge
Outfeed Table
Feeler Gauge
Support Blocks
Figure 59. Using feeler gauge to check outfeed
table-cutterhead height.
Cap Screw
5. Place the straightedge on the front side of the
outfeed table so it hangs over the cutterhead,
as shown in Figure 59, then try to fit a
feeler gauge or combination of feeler gauges
between the cutterhead and bottom of the
straightedge.
Figure 60. Location of front outfeed table
support blocks.
2. Fit the 0.060" feeler gauge (or combination
of feeler gauges) onto the front side of the
cutterhead, then place the straightedge on
the front of the outfeed table and over the
feeler gauge.
—If the feeler gauge slides with slight resis-
tance between the ruler and cutterhead
and no gaps appear between the straight-
edge and the table, then the outfeed table
is already parallel with the cutterhead. Go
to Checking Infeed Table Parallelism on
Page 41.
3. While an assistant holds the feeler gauge and
straightedge, adjust the height of each sup-
port block until no gaps appear between the
straightedge and the table.
—If the feeler gauge does not fit between the
ruler and cutterhead, or if there is a gap
between the straightedge and the table,
the outfeed table is not parallel with the
cutterhead. Correct the outfeed table paral-
lelism, then correct the infeed table paral-
lelism. Continue to Correcting Outfeed
Table to Cutterhead Parallelism.
4. Tighten the cap screws on the suport blocks
to secure the adjustment.
5. Using the straightedge and the 0.060" feeler
gauge, verify again that no gaps appear
between the table and the straightedge.
6. Repeat Steps 1–5 until the front outfeed table
parallelism is correct, then repeat Checking
Outfeed Table Parallelism on Page 39 to
ensure the outfeed table height above the
cutterhead is equal across the table.
7. Continue to Checking Infeed Table
Parallelism on Page 41.
-40-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
—If the straightedge sits flat against both
the infeed and outfeed table, then the
tables are parallel. Continue to Inspecting
Knives on Page 42.
Checking Infeed Table Parallelism
1. Follow all the steps for checking the outfeed
table parallelism to first make sure that the
outfeed table is parallel with the cutterhead.
—If the straightedge does not sit flat against
both the infeed and outfeed table in
any of the positions, then continue to
the Adjusting Infeed Table Parallelism
instructions.
2. Place the straightedge halfway across the
infeed table and halfway over the outfeed
table, and adjust the infeed table even with
the outfeed table, as shown in Figure 61.
Adjusting Infeed Table Parallelism
Straightedge
1. Perform the "Checking/Adjusting Table
Parallelism" procedure on Page 39, including
making any necessary adjustments so the
cutterhead and outfeed table are parallel.
Outfeed Table
Infeed Table
2. Place the straightedge halfway across the
infeed table and halfway over the outfeed
table, and adjust the infeed table even with
the outfeed table, as shown in Figure 61.
Figure 61. Infeed and outfeed tables set evenly.
—If a knife touches the straightedge, turn the
cutterhead so the knives do not interfere.
3. Place the straightedge in one of the positions
shown in Figure 62.
3. Place the straightedge in the positions shown
in Figure 62. In each position, the straight-
edge should sit flat against both the outfeed
table and the infeed table—you should not
see any gaps between the bottom of the
straightedge and the infeed table.
—If the front of the infeed table is higher or
lower than the outfeed table, or if the rear
of the infeed table is higher or lower than
the outfeed table, continue to Step 4.
—If the straightedge sits flat against both
the infeed and outfeed table, then the
tables are parallel. Continue to Inspecting
Knives on Page 42.
Black Lines Represent
Straightedge Positions
from Overhead View
Figure 62. Straightedge positions for checking
infeed/outfeed table parallelism.
-41-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Loosen the eight hex bolts and flange nuts
on both sides of the infeed table, as shown in
Figures 63 and 64.
Inspecting Knives
Tools Needed:
Qty
Knife Setting Gauge .......................................... 1
Straightedge ...................................................... 1
The height of the knives can be inspected with the
included knife setting gauge.
Inspecting the height of the knives ensures that
they are set evenly with the outfeed table at their
highest point in the cutterhead rotation.
To inspect the knives with the knife setting
gauge:
Figure 63. Location of infeed table adjustment
bolts, front view.
1. DISCONNECT THE JOINTER/PLANER
FROM THE POWER SOURCE!
2. Perform Steps 2–7 in Setting Outfeed Table
Height on Page 17.
—If the top of the knife just touches the bottom
of the gauge when it is at the highest point
of rotation on both sides of the cutterhead,
then that knife is set correctly. (Repeat this
inspection with the other knife.)
—If the top of the knife does not touch the
bottom of the gauge as described, then
reset that knife. Continue to Adjusting/
Replacing Knives on Page 43 ( Repeat
this inspection with the other knife before
resetting.)
Figure 64. Locations of the infeed table
adjustment bolts.
5. While an assistant holds the straightedge
over both tables, lift or lower the infeed table,
then tighten the hex bolts and nuts as needed
so there is little to no visible gap between the
bottom of the straightedge and the top of the
infeed table.
3. REPLACE the front access panel and the
blade guard assembly!
6. Continue adjusting the infeed table until it
is parallel with the outfeed table in each of
the positions shown in Figure 62. Some trial
and error and a good deal of patience will
be needed to successfully accomplish this
adjustment.
Tip: Tighten the front and rear bolts finger
tight and tap the table up or down. This will
help dial in the adjustment.
7. Once the infeed and outfeed tables are par-
allel with each other, proceed to Inspecting
Knives.
-42-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
The Model G0675 comes with jack screws for
cutterhead adjustments (see Figure 66).
Adjusting/Replacing
Knives
Loosen
Knife
Tighten
Tools Needed:
Qty
Straightedge ...................................................... 1
Hex Wrench 5mm.............................................. 1
Wrench 8 mm.................................................... 1
Setting the knives correctly is crucial to the proper
operation of the jointer/planer and is very impor-
tant in keeping the knives sharp. If one knife is
higher than the others, it will do the majority of the
work, and thus, dull much faster than the others.
Jack
Screw
Gib Bolt
Gib
Knife Setting Gauge Method: The gauge is
placed on the outfeed table over the cutterhead,
as shown in Figure 65, and the knife heights
are set to just touch the gauge. The knife setting
gauge makes it easy to ensure that the knives
project out of the cutterhead evenly.
Figure 66. Cutterhead profile diagram.
To set or replace the knives:
1. DISCONNECT THE JOINTER/PLANER
FROM THE POWER SOURCE!
2. Remove the blade guard and fence from the
table.
3. Remove the rear access panel to expose the
cutterhead pulley.
Outfeed
Infeed
4. Rotate the cutterhead pulley to give you good
access to one of the cutterhead knives.
5. Loosen the cutterhead gib bolts, starting in
the middle and alternating back-and-forth
until all of the gib bolts are loose but not fall-
ing out.
Figure 65. Using knife setting gauge to set knife
height.
—If this is the first time you are setting the
knives, or if you are replacing them, remove
a gib and knife from the cutterhead. Clean
the gib and clean inside the cutterhead slot
to remove all pitch or sawdust. Coat the
knife and gib with a metal protectant (Page
31).
-43-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
6.ꢀ Edh^i^dcꢀ i]Zꢀ `c^[Zꢀ \Vj\Zꢀ dkZgꢀ i]Zꢀ `c^[Zꢀ Vhꢀ
h]dlcꢀ^cꢀFigure 65ꢀVcYꢀaddhZcꢀi]Zꢀ\^WꢀWdaihꢀ
jci^aꢀi]Zꢀ`c^[Zꢀ^hꢀXdbeaZiZanꢀaddhZ#
Setting Fence Stops
I]Zꢀ[ZcXZꢀhidehꢀh^bea^[nꢀi]ZꢀiVh`ꢀd[ꢀVY_jhi^c\ꢀi]Zꢀ
[ZcXZꢀidꢀ)*ßꢀVcYꢀ.%ß#ꢀꢀ
7.ꢀ Jh^c\ꢀ Vꢀ *bbꢀ ]Zmꢀ lgZcX]!ꢀ gdiViZꢀ i]Zꢀ _VX`ꢀ
hXgZlhꢀ ꢂFigure 67ꢃꢀ ^cꢀ i]Zꢀ VXXZhhꢀ ]daZhꢀ idꢀ
gV^hZꢀdgꢀadlZgꢀi]Zꢀ`c^[Z#ꢀL]Zcꢀi]Zꢀ`c^[Zꢀ^hꢀhZiꢀ
XdggZXian!ꢀ^iꢀl^aaꢀWVgZanꢀidjX]ꢀi]ZꢀWdiidbꢀZY\Zꢀ
d[ꢀi]Zꢀ`c^[ZꢀhZii^c\ꢀ\Vj\ZꢀdcꢀWdi]ꢀh^YZhꢀd[ꢀi]Zꢀ
XjiiZg]ZVYꢀl]Zcꢀ^iꢀ^hꢀgdiViZYꢀWVX`ꢀVcYꢀ[dgi]#ꢀ
Hcj\ꢀi]Zꢀ\^WꢀWdaihꢀi^\]iꢀZcdj\]ꢀidꢀ_jhiꢀ]daYꢀ
i]Zꢀ`c^[Zꢀ^cꢀeaVXZ#ꢀGZeZViꢀSteps 5-7ꢀl^i]ꢀi]Zꢀ
gZbV^c^c\ꢀ`c^[Z#
Tools Needed
Qty
)*•ꢀHfjVgZꢀ######################################################## &
.%•ꢀHfjVgZꢀ######################################################## &
Ha^Y^c\ꢀ7ZkZaꢀ###################################################### &
=ZmꢀLgZcX]ꢀ(bbꢀ############################################## &
=ZmꢀLgZcX]ꢀ,bbꢀ############################################## &
GZ[ZgꢀidꢀFigures 69-70ꢀidꢀ^YZci^[nꢀi]Zꢀ.%ßꢀVcYꢀ)*ßꢀ
[ZcXZꢀhideꢀXdbedcZcih#
.%ßꢀ;ZcXZꢀ
AdX`ꢀCji
Figure 67.ꢀ?VX`ꢀhXgZlꢀVXXZhhꢀ]daZ#
8.ꢀ GdiViZꢀ i]Zꢀ XjiiZg]ZVYꢀ idꢀ i]Zꢀ [^ghiꢀ `c^[Zꢀ ndjꢀ
VY_jhiZY#ꢀ Ha^\]ianꢀ i^\]iZcꢀ Vaaꢀ i]Zꢀ \^Wꢀ Wdaih!ꢀ
hiVgi^c\ꢀViꢀi]Zꢀb^YYaZꢀVcYꢀldg`^c\ꢀndjgꢀlVnꢀidꢀ
i]ZꢀZcYhꢀWnꢀVaiZgcVi^c\ꢀaZ[iꢀVcYꢀg^\]iꢀꢂFigure
68ꢃ#ꢀGZeZViꢀi]^hꢀhiZeꢀdcꢀi]ZꢀgZbV^c^c\ꢀ`c^[Z#
)*ßꢀHideꢀHXgZl
Figure 69.ꢀ.%˚ꢀadX`ꢀcjiꢀVcYꢀ)*ßꢀhideꢀhXgZl#
)ꢀ
*ꢀ
(ꢀ
&ꢀ
'ꢀ
Figure 68.ꢀ<^WꢀWdaiꢀi^\]iZc^c\ꢀhZfjZcXZ#
.%ßꢀHideꢀ
)*ßꢀAdX`ꢀ
Cji
HXgZl
9.ꢀ GZeZViꢀ Step 8!ꢀ Wjiꢀ [^cVaꢀ i^\]iZcꢀ ZVX]ꢀ \^Wꢀ
Wdai#
10.ꢀ GZeaVXZꢀi]ZꢀgZVgꢀVXXZhhꢀeVcZa!ꢀWaVYZꢀ\jVgY!ꢀ
VcYꢀ[ZcXZ#
6c\aZYꢀ7gVX`Zi
Figure 70#ꢀ.%˚ꢀhideꢀhXgZlꢀVcYꢀ)*ßꢀadX`ꢀcji#
"))"
<%+,*ꢀ&%ꢁꢀ?d^ciZg$EaVcZgꢀ8dbWdꢀBVX]^cZ
Download from Www.Somanuals.com. All Manuals Search And Download.
To set the 90˚ fence stop:
3. Using a 45° square, adjust the fence to the
45° outward position (Figure 72).
1. Loosen the 90˚ lock nut (Figure 69) and stop
screw (Figure 70), and loosen the fence tilt
locks.
2. Using a 90˚ square, adjust the fence to the
90˚ position, as shown in Figure 71.
Figure 72. Adjusting fence 45˚ outward.
4. Secure the 45° stop screw and lock nut
against the angled bracket, then tighten the
lock nut.
Figure 71. Adjusting fence to 90˚.
3. Adjust the 90˚ stop screw until it contacts the
angled bracket on the fence, then tighten the
lock nut.
To set the 45˚ fence stop:
1. Loosen the 45˚ lock nut (Figure 70) and stop
screw (Figure 69), then loosen the fence tilt
locks.
2. Move the blade guard out of the way, loosen
the fence height lock knobs, then slide the
fence down until it is flush with the table.
-45-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Locate the hex nuts and springs on both
sides of the feed rollers, as shown in Figure
73.
Spring Tension
Feed roller spring tension must be adjusted so
that feed roller pressure is uniform for planer
operation. Roller spring tension will vary, depend-
ing on the type of wood you plane. This is usually
determined from trial-and-error.
5. Adjust the hex nuts so they are at the recom-
mended factory setting—1⁄2" (13mm) from the
bottom of the feed roller bolts (see Figure
74).
Generally speaking, less spring tension is more
forgiving on workpieces. Therefore, if you primar-
ily plane milled lumber with relatively consistent
surfaces, you can get away with having less
spring tension. If you mainly plane rough lumber
with inconsistent surface heights, more spring
tension is a must to keep the workpiece feeding
through the planer without stopping.
Spring
Hex Nut
1
⁄2"
Bolt
If workpieces regularly stop feeding during opera-
tion, it may be a sign of weak spring tension.
Figure 74. Recommended chain tension setting.
Tools Needed:
Hex Wrench 5mm.............................................. 1
Wrench 10mm ................................................... 1
Qty
6. Remove the hex wrench, move the tensioner
back to re-tension the chain, the re-install the
front and rear panels with the cap screws you
removed earlier.
To adjust feed roller spring tension:
7. Run a test board through the planer.
1. DISCONNECT THE JOINTER/PLANER
FROM THE POWER SOURCE!
—If the workpiece slips when you feed it,
repeat Steps 1-4, then turn the hex nuts 1⁄2
to 1 turn clockwise to increase spring ten-
sion. Continue to Step 8.
2. Set up the machine for planer operations,
remove the cap screws that secure the front
and back access panels to the frame (see
Figure 44 on Page 33), then remove the
panels.
—If the workpiece is abruptly grabbed when
initially fed into the planer, repeat Steps
1
1-4, then turn the hex nuts ⁄2 to 1 turn
3. Move the chain tensioner away from the
chain and place a 5mm hex wrench into the
hole in the frame, as shown in Figure 73, to
hold the tensioner and de-tension the chain.
counterclockwise to decrease spring ten-
sion. Continue to Step 8.
—If the workpiece feeds smoothly, the spring
tension is correct.
8. Repeat Steps 6-7, and continue adjusting the
spring tension until it is right for the type of
wood you are planing.
Hex Wrench
Tensioner
Hex
Nut
Springs
Figure 73. Location of adjustments nuts (front
panel removed for access).
-46-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Loosen the four cap screws on the wheel
bracket, and one cap screw on the infeed belt
wheel, raise the infeed wheel and roll the flat
belt off (see Figure 76).
Replacing Feed
Rollers
After long term use of the jointer/planer the rubber
coating on the feed rollers may wear, resulting in
workpieces feeding erratically. When this hap-
pens, replace both the front and rear feed rollers
as a set.
Wheel Bracket
Infeed
Belt
Wheel
Sprocket
Wheel
Tools Needed:
Qty
Hex Wrench 4mm.............................................. 1
Wrench 13mm ................................................... 1
Wrench 10mm ................................................... 1
Cap
Screws
To replace the front and rear feed rollers:
Figure 76. Wheel bracket cap screws.
1. DISCONNECT THE JOINTER/PLANER
FROM THE POWER SOURCE!
6. Remove the hex nuts and springs (see
Figure 73 on Page 46) from both sides of the
front and rear feed rollers.
2. Remove the eight cap screws that secure
the front and rear access panels to the frame
(see Figure 44 on Page 33), then remove the
panels.
7. While rotating the lower sprocket wheel clock-
wise, walk the chain off of the front feed roller
sprocket (Figure 77), then remove the chain
from both feed roller sprockets.
3. Remove the four special bolts and washers
that secure the infeed table to the frame, then
remove the infeed table (see Figure 75).
Bolts
Front Feed Roller
Sprocket
Figure 75. Location of bolts that secure infeed
Figure 77. Removing feed roller chain.
table.
8. Raise the outfeed table and engage the lock
4. Move the chain tensioner away from the
chain and place a 5mm hex wrench into the
hole in the frame, as shown in Figure 73 on
Page 46, to hold the chain tensioner and
keep the chain detensioned.
arm.
9. Remove the front and rear feed rollers, then
install the new feed rollers.
10. Close and lock the outfeed table.
-47-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Place the chain back onto the feed roller
sprockets, rolling it on in the same manner
that you removed it in Step 7.
NOTICE
During the next step, DO NOT let the chain
fall off the sprockets—returning it to its
proper location without changing the table
adjustments can be very difficult.
12. Re-install the springs and hex nuts onto both
sides of the new feed rollers, tightening the
1
nuts until they are ⁄2" (13mm) from the bot-
tom of the bolts, as shown in Figure 74 on
Page 46.
3. Loosen the two lock nuts on the idler sprocket
(Figure 78 and 79) and move the sprocket
behind the chain to tighten it.
13. Remove the hex wrench to re-tension the
chain.
14. Re-install the flat belt, making sure that it is
seated into the infeed wheel grooves, then
secure the cap screws on the wheel bracket
and the infeed belt wheel.
15. Check the flat belt tension (refer to Page 33,
Step 6).
Lock Nut
16. Re-install the infeed table with the bolts and
washers you removed earlier, and reinstall
the side panels with the cap screws.
Figure 78. Top idler sprocket lock nut (viewed
from planer table infeed side).
Chain Tension
The chain drive transfers movement from the
handwheel to elevate the headstock. The chain
drive can be adjusted to remove slack if the chain
stretches over time or is loosened during table
leveling procedures.
This procedure will require you to remove the
jointer/planer assembly from the base to adjust
the chain tension.
Lock Nut
(Hidden by
Sprocket)
Idler Sprocket
Tools Needed:
Qty
Figure 79. Underside of table and idler sprocket.
Wrench or Socket 13mm................................... 2
Forklift................................................................ 1
Sawhorses......................................................... 2
4. Using the forklift, place the table back on
the base, and relatch the base to the jointer/
planer.
To adjust the chain tension:
1. DISCONNECT THE JOINTER/PLANER
FROM THE POWER SOURCE!
2. Perform Steps 2–7 in the Table Parellelism
Adjustments subsection on Page 50, except
you will not need to remove the side panels—
unless you plan to check table parallelism
after checking chain tension.
-48-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
How the table sits in relation to the base from
front-to-back is also important (see Figure 81).
The tolerances on the front-to-back positioning
are not as critical as the cutterhead/table side-to-
side positioning. Therefore, the maximum allow-
able tolerance for the front-to-back parallelism is
not more than 0.040".
Planer Table
Parallelism
Table parallelism is critical to the operation of the
machine. As such, it is essential that the table is
parallel with the cutterhead (within 0.003") from
side-to-side, as illustrated in Figure 80.
Table
Parallel
FRONT
Parallel
Maximum Allowable Tolerances:
Cutterhead to Table Side-to-Side..............0.003"
Headstock to Table Front/Back.................0.040"
Base
BACK
Tools Needed:
Qty
Rotacator........................................................... 1
Standard Screwdriver........................................ 1
Wrench or Sockets 13mm................................. 2
Hex Wrench 5mm.............................................. 1
Sawhorses......................................................... 2
Assistant............................................................ 1
Forklift................................................................ 1
White Marker or Correction Fluid ..............Varies
Not-Parallel
Not-Parallel
Figure 81. Front-to-back parallelism.
Table Parallelism Inspection
The easiest way to determine if your planer table
has a parallelism problem with the base is to
plane a workpiece and measure the thickness in
multiple locations. If the workpiece is tapered from
left-to-right or from front-to-back, then parallelism
may be a problem.
Cutterhead
Parallel
Parallel
Table
SIDE-TO-SIDE
FRONT
VIEW
Use your Rotacator (Page 31) to further inspect
the table parallelism, as shown in Figure 82 and
Figure 83 on Page 50.
Not-Parallel
Not-Parallel
To inspect the cutterhead-table parallelism:
1. Place the jointer outfeeed table in the upright
position, then rotate the dust chute assembly
up and over the cutterhead to access the
cutterhead and planer table below.
Figure 80. Side-to-side parallelism of table and
cutterhead.
-49-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Place the Rotacator on the planer table under
one side of the cutterhead, then raise the
planer table until the dial rotates one full turn
to "0" (see Figure 82).
7. Move the Rotacator to the same position
under the outfeed side of the planer table and
note the reading.
If you do not have a Rotacator, a wood block and
feeler gauges may be used, but extra care must
be taken to ensure accuracy. If the table is not
within the maximum allowable tolerances, it must
be adjusted.
Cutterhead
Table Parallelism Adjustments
The table is adjusted by turning the chain sprock-
ets underneath the base. This procedure can take
a great deal of patience and time.
To adjust the table parallelism:
Table
1. DISCONNECT THE JOINTER/PLANER
FROM THE POWER SOURCE!
Figure 82. Measuring side-to-side parallelism.
2. Convert the machine for jointer operations,
then remove the fence, fence arm assembly,
and lock the outfeed table.
3. Rock the cutterhead back and forth and
rotate the cutterhead until the dial is at "0".
4. Move the Rotacator to the same position on
the oppposite side of the table and note the
reading.
3. Remove the front and rear access panels,
then unlatch the jointer/planer assembly from
the base.
5. Place the Rotacator on the base under the
center of the infeed side of the planer table,
so the plunger contacts the webbing evenly
(see Figure 83).
4. Place sawhorses about 16 inches apart.
5. Place forklift forks under both tables, making
sure they do not contact the outfeed table
lock lever or the infeed table height lever, but
enough so the machine does not slide off of
the forks.
6. Lower the table and zero out the Rotacator.
Table
6. While an assistant steadies the jointer tables,
lift the machine off of the base and set it onto
the sawhorses, as shown in Figure 84.
Base
Figure 83. Measuring front-to-back parallelism.
16"
Figure 84. Machine supported by sawhorses.
-50-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Locate the chain on the underside of the
Anti-Kickback
Fingers
table.
8. Loosen the idler sprocket (see Chain Tension
instructions on Page 48).
The Model G0675 provides an anti-kickback sys-
tem as a safety feature. The anti-kickback fingers
hang from a rod suspended across the cutterhead
casting. The anti-kickback fingers should be
inspected regularly.
9. Mark the location of one tooth in the sprocket
that you are adjusting.
10. Move the chain away from only the sprocket
you want to adjust so only that sprocket can
be turned independent of the chain.
Check the fingers (Figure 85) to ensure that they
swing freely and easily. If the fingers do not swing
freely and easily, clean them with a wood resin
solvent.
Note: If the left side of the table is too high
(viewed from the planer table infeed), the
front and rear left sprockets will need to be
adjusted. Each tooth on the sprocket rep-
resents .007" of vertical movement as the
cogs are turned. Make sure, as you turn the
sprockets, to keep an accurate tooth count to
ensure that the table is adjusted equally.
11. Carefully turn the sprocket (clockwise to
lower the table; counterclockwise to raise the
table) just enough to position the next tooth at
the marked location, then fit the chain around
sprocket again.
Anti-Kickback
Fingers
12. Repeat Steps 9–11 with each sprocket that
needs to be adjusted until the table-to-cutter-
head clearance is within 0.007" from one side
to the other.
Figure 85. Anti-kickback fingers.
13. Make sure the chain is properly fitted on the
sprockets, and tighten the idler sprocket lock
nuts.
Proper operation of the anti-kickback fin-
gers is essential for the safe operation of
this machine. Failure to ensure that they
are working properly could result in serious
operator injury.
14. Place the table back on the base with the
forklift, relatch the base to the jointer/planer,
and reinstall the access panels.
Do not apply oil or other lubricants to the anti-
kickback fingers. Oil or grease will attract dust,
restricting the free movement of the fingers.
-51-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 8: WIRING
These pages are current at the time of printing. However, in the spirit of improvement, we may make chang-
es to the electrical systems of future machines. Study this section carefully. If there are differences between
your machine and what is shown in this section, call Technical Support at (570) 546-9663 for assistance
BEFORE making any changes to the wiring on your machine.
Wiring Safety Instructions
1. SHOCK HAZARD. Working on wiring that
is connected to a power source is extremely
dangerous. Touching electrified parts will
result in personal injury including but not lim-
ited to severe burns, electrocution, or death.
Disconnect the power from the machine
before servicing electrical components!
6. MOTOR WIRING. The motor wiring shown
in these diagrams is current at the time of
printing, but it may not match your machine.
Always use the wiring diagram inside the
motor junction box.
7. WIRE/COMPONENT DAMAGE. Damaged
wires or components increase the risk of seri-
ous personal injury, fire, or machine damage.
If you notice that any wires or components
are damaged while performing a wiring task,
replace those wires or components before
completing the task.
2. QUALIFIED ELECTRICIAN. Due to the
inherent hazards of electricity, only a quali-
fied electrician should perform wiring tasks
on this machine. If you are not a quali-
fied electrician, get help from one before
attempting any kind of wiring job.
8. CAPACITORS. Some capacitors store an
electrical charge for up to five minutes after
being disconnected from the power source.
To avoid being shocked, wait at least this
long before working on capacitors.
3. WIRE CONNECTIONS. All connections
must be tight to prevent wires from loosen-
ing during machine operation. Double-check
all wires disconnected or connected during
any wiring task to ensure tight connections.
9. EXPERIENCING DIFFICULTIES. If you are
experiencing difficulties understanding the
information included in this section, contact
our Technical Support at (570) 546-9663.
4. MODIFICATIONS. Using aftermarket parts
or modifying the wiring beyond what is
shown in the diagram may lead to unpredict-
able results, including serious injury or fire.
5. CIRCUIT REQUIREMENTS. You MUST fol-
low the requirements on Page 10 when con-
necting your machine to a power source.
The photos and diagrams
included in this section are
best viewed in color. You
can view these pages in
-52-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Overview
1
3
(Inside Machine)
2
(Inside Machine)
Figure 86. Component location key.
220V Single-Phase Motor
Page 55
WIRING HARNESS KEY
Power Cord
A
B
C
3
Limit Switch Harness
Motor Harness
C
Cutterhead Limit Switch
Page 55
B
2
Switch
Assembly
Page 54
Power Supply
Connection
Page 55
1
A
220 VAC
6-15 PLUG
Recommended
Figure 87. Wiring overview.
-53-
READ ELECTRICAL SAFETY
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
ON PAGE 52!
ON/OFF Switch Assembly Wiring
Figure 88. Switch terminal connections.
WIRING HARNESS KEY
A
B
Power Cord
C
Motor Harness
Limit Switch Harness
1
O
ON/OFF Switch
(viewed from behind)
(Figure 88)
WARNING!
SHOCK HAZARD!
Disconnect power
before working on
wiring.
B
A
C
To Power Supply
To Limit Switch
To Motor
Page 55
Page 55
Page 55
Figure 89. ON/OFF switch assembly wiring.
READ ELECTRICAL SAFETY
-54-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
ON PAGE 52!
Components Wiring
220V Single-Phase Motor
(Figure 90)
Start Capacitor
35M 450V
2 1
Z2
U1
U2
Z1
3
3
450V
PA9
2
U
450V
PA9
2
U
450V
PA9
Figure 90. Motor wiring.
C
A
WIRING HARNESS KEY
B
Power Cord
A
B
C
Limit Switch Harness
Motor Harness
Cutterhead
Limit Switch
(Figure 91)
Ground
2
2
G
Hot
220
13
21
14
22
VAC
Hot
6-15 Plug
(As Recommended)
Figure 91. Limit switch.
-55-
READ ELECTRICAL SAFETY
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
ON PAGE 52!
SECTION 9: PARTS
Table Breakdown
1
2
3
4
8
6
5
9
7
14
11
13
10
12
15
17
1
23
21
24
22 23
17
25
18
19 20
8
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
P0675001
P0675002
P0675003
P0675004
P0675005
P0675006
P0675007
P0675008
P0675009
P0675010
P0675011
P0675012
P0675013
P0675014
CAP SCREW M8-1.25 X 30
TABLE SUPPORT BLOCK
15
16
17
18
19
20
21
22
23
24
25
26
27
P0675015
P0675016
P0675017
P0675018
P0675019
P0675020
P0675021
P0675022
P0675023
P0675024
P0675025
P0675026
P0675027
SUPPORT BLOCK
OUTFEED TABLE
LOCK NUT M8-1.25
2
3
TABLE SUPPORT BRACKET
BRACKET PIVOT SHAFT
RETAINING RING
4
FLANGE NUT M8-1.25
5
POSITIONING WASHER
TABLE LOCKING PLATE
CAP SCREW M8-1.25 X 16
CAP SCREW M8-1.25 X 25
6
INFEED TABLE
7
INFEED TABLE INDICATOR
FLAT WASHER 6MM
8
9
PHLP HD SCR M6-1 X 12
SPECIAL BOLT M8-1.25 X 14
LOCK WASHER 12MM
INFEED TABLE LEVER
CAP SCREW M5-.8 X 12
HANDLE COAT
TABLE HEIGHT SUPPORTER
TABLE HEIGHT CONNECTOR
FLAT WASHER 8MM
LOCK ARM
10
11
12
13
14
LOCK NUT M6-1
-56-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Motor Assembly Breakdown
106
105
107
108-1
108-3
108-4
108-2
104
101
102
103
123
122
108
109
110
121
109
110
114
124
120
113
111
112
114
113
119
114
110
118
115
112
116
115
116
112
115
116
110
114
117
DESCRIPTION
REF PART #
REF PART #
DESCRIPTION
101
102
103
104
105
106
107
108
P0675101
CUTTERHEAD LIMIT SWITCH
CABLE SAFETY RING
HEX BOLT M6-1 X 12
FLANGE NUT M6-1
111
112
113
114
115
116
117
118
119
120
121
122
123
124
P0675111
P0675112
P0675113
P0675114
P0675115
P0675116
P0675117
P0675118
P0675119
P0675120
P0675121
P0675122
P0675123
P0675124
MOTOR BRACKET
P0675102
P0675103
P0675104
P0675105
P0675106
P0675107
P0675108
CARRIAGE BOLT M8-1.25 X 16
FLAT WASHER 8MM
LOCK NUT M8-1.25
LOCK WASHER 8MM
HEX NUT M8-1.25
HEX BOLT M8-1.25 X 25
SPECIAL WASHER 8MM
MOTOR WHEEL
POWER CORD 14AWG X 3C
RUBBER SAFETY RING
SWITCH ASSEMBLY
RUBBER SAFETY RING
MOTOR LABEL
MOTOR 2.4HP 220V SINGLE-PHASE
MOTOR FAN COVER
108-1 P0675108-1
108-2 P0675108-2
108-3 P0675108-3
108-4 P0675108-4
MOTOR FAN
S CAPACITOR 35M 450V 1-3/4 x 3-3/4
JUNCTION BOX
SWITCH BRACKET
109
110
P0675109
P0675110
HEX BOLT M6-1 X 25
MOTOR CORD
FLAT WASHER 8MM
LIMIT SWITCH CORD
-57-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Frame Breakdown
219
215
217
216
218
213
212
203
214
201
220
221
202
203
201
204
205
210
207
208
206
209
REF PART #
206
211
REF PART #
DESCRIPTION
DESCRIPTION
201
202
203
204
205
206
207
208
209
210
211
P0675201
OUTSIDE BASE PLATE
REAR BASE PLATE
212
213
214
215
216
217
218
219
220
221
P0675212
P0675213
P0675214
P0675215
P0675216
P0675217
P0675218
P0675219
P0675220
P0675221
FRAME
P0675202
P0675203
P0675204
P0675205
P0675206
P0675207
P0675208
P0675209
P0675210
P0675211
FLANGE NUT M8-1.25
FRONT BASE PLATE
HEX BOLT M8-1.25 X 16
GUIDE BODY
BUTTON HD CAP SCR M6-1 X 12
CAP SCREW M6-1 X 16
MOTOR CASE PLATE
LOCK NUT M6-1
COMPRESSION SPRING
SAFETY SWITCH ROD
E-CLIP 5MM
PIVOT SHAFT
LOCK NUT M6-1
CASE PLATE
HEX NUT M10-1.5
RIVET NUT M6-1 X 15
PLATE
FOOT SUPPORT M10-1.5
-58-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Fence Assembly Breakdown
302
303
323
303
304
301
322
302
312
313
314
315
318
316
320
319
321
317
308
306
309
311
310
305
307
307
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
301
302
303
304
305
306
307
308
309
310
311
312
P0675301
P0675302
P0675303
P0675304
P0675305
P0675306
P0675307
P0675308
P0675309
P0675310
P0675311
P0675312
LOCKING INSERT PLATE
TAP SCREW M4.8 X 12
FENCE COVER
FENCE
313
314
315
316
317
318
319
320
321
322
323
P0675313
P0675314
P0675315
P0675316
P0675317
P0675318
P0675319
P0675320
P0675321
P0675322
P0675323
HEX BOLT M5-.8 X 12
RIP FENCE BRACKET
FLAT WASHER 4MM
HANDLE BRACKET
GUARD PLATE
ALIGNMENT SHAFT
TILT LEVER
FENCE TILTING BRACKET
HEX NUT M4-.7
FLAT WASHER 6MM
END PLUG
CAP SCREW M4-.7 X 8
BLADE GUARD BRACKET
LOCK HANDLE M8-1.25 X 16
BLADE GUARD COVER
WING SCREW M6-1
CARRIAGE BOLT M6-1 X 16
RIP FENCE RAIL
END PLUG
-59-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Feed Gear Assembly Breakdown
403
417
416
418
420
416
418
419
421
422
423
424
425
426
427
428
403
415
444
427
429
416
450
430
431
432
433
434
448
436
447
433
435
440
441
445
439
449
438
439
437
442
432
443
401
402
403
404
405
406
407
408
409
445
446
410
404
406
411
451
452
412
413
414
-60-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Feed Gear Assembly Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
P0675401
P0675402
P0675403
P0675404
P0675405
P0675406
P0675407
P0675408
P0675409
P0675410
P0675411
P0675412
P0675413
P0675414
P0675415
P0675416
P0675417
P0675418
P0675419
P0675420
P0675421
P0675422
P0675423
P0675424
P0675425
P0675426
LOCKING PLATE
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
P0675427
P0675428
P0675429
P0675430
P0675431
P0675432
P0675433
P0675434
P0675435
P0675436
P0675437
P0675438
P0675439
P0675440
P0675441
P0675442
P0675443
P0675444
P0675445
P0675446
P0675447
P0675448
P0675449
P0675450
P0675451
P0675452
FLAT WASHER 6MM
LOCK NUT M6-1
POSITIONING PLATE
FLANGE NUT M8-1.25
LOCKING CONNECTING PLATE
ROTATING SHAFT
E-CLIP 8MM
CAP SCREW M6-1 X 20
WHEEL BRACKET
SPROCKET WHEEL ASSEMBLY
SPECIAL WASHER 8MM
NEEDLE BEARING 14 X 12 X 20
INFEED BELT WHEEL
TUBE
LOCK WASHER 10MM
LOCK NUT M10-1.5
FLAT WASHER 10MM
ROLL PIN 4 X 10
WHEEL SHAFT
SUPPORT SCREW
ROLL PIN 4 X 10
WHEEL SHAFT
SLIDING BLOCK
LOCK HANDLE
FLAT WASHER 16MM
EXT RETAINING RING 16MM
TOOTHED BELT WHEEL
LOCK WASHER 8MM
CAP SCREW M8-1.25 X 70
E-CLIP 8MM
LOCK HANDLE SUPPORT
FLAT HD SCR M6-1 X 12
FLANGE NUT M8-1.25
CHAIN
FLAT WASHER 10MM
NEEDLE BEARING 10 X 12 X 17
TENSION SPROCKET
POSITIONING SHAFT
TORSION SPRING
TENSION SHAFT
NEEDLE BEARING 12 X 10 X 16
TUBE
TUBE
NEEDLE BEARING 16 X 16 X 22
EXT RETAINING RING 12MM
LOCK NUT M8-1.25
SHAFT
TENSION SPROCKET
TENSION BRACKET
FLAT BELT 5/16" X 1/16" X 29"
V-BELT K-20 5/16" X 1/4"
-61-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Cutterhead-Feed Rollers Breakdown
523
525
507
528
517
524
520
509
510
508
518
519
523
517
501
502
506
534
529
534
535
522
521
525
504
530
503
505
511
513
510
508
535
526
536
537
524
519
518
511
531
515
533
532 534
509
516
512
538
REF PART #
P0675501
DESCRIPTION
CUTTERHEAD WITH KNIVES
CUTTERHEAD
REF PART #
P0675520
DESCRIPTION
FEED ROLLER
501
502
503
504
505
506
507
508
509
510
511
512
513
515
516
517
518
519
520
521
522
523
524
525
526
528
529
530
531
532
533
534
535
536
537
538
P0675502
P0675503
P0675504
P0675505
P0675506
P0675507
P0675508
P0675509
P0675510
P0675511
P0675512
P0675513
P0675515
P0675516
P0675517
P0675518
P0675519
P0675521
P0675522
P0675523
P0675524
P0675525
P0675526
P0675528
P0675529
P0675530
P0675531
P0675532
P0675533
P0675534
P0675535
P0675536
P0675537
P0675538
SPROCKET WHEEL
ROLL PIN 4 X 25
HOOP COVER
KNIFE
KNIFE GIB
KNIFE GIB SCREW
JACK SCREW
HEX BOLT M8-1.25 X 25
HEX BOLT M8-1.25 X 30
FLANGE NUT M8-1.25
RIBBED V-BELT 1000J4
ANTI-KICKBACK SHAFT
POSITIONING SHAFT
ANTI-KICKBACK FINGER
EXT RETAINING RING 8MM
FLAT WASHER 10MM
CAP SCREW M6-1 X 16
EXT TOOTH WASHER 6MM
WRENCH 8/10
CUTTERHEAD PULLEY
BALL BEARING 6005ZZ
CUTTERBLOCK BRACKET
O- RING
BEARING CLAMP
CAP SCREW M6-1 X 25
FLANGE NUT M6-1
FLAT WASHER 8MM
HEX BOLT M8-1.25 X 16
CLAMPING HOOP
COMPRESSION SPRING
LOCK NUT M6-1
HEX WRENCH 5MM
KNIFE SETTING GAUGE
-62-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Access Panels Breakdown
601
612
607
610
611
601
602
612
611
603
608
604
605
606
607
605
604
606
608
605
604
609
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
601
602
603
604
605
606
P0675601
P0675602
P0675603
P0675604
P0675605
P0675606
PHLP HD SCR M5-.8 X 16
RIGHT UPPER COVER
RIGHT ACCESS PANEL
BUTTON HD CAP SCR M6-1 X 10
FLAT WASHER 6MM
607
608
609
610
611
612
P0675607
P0675608
P0675609
P0675610
P0675611
P0675612
CAP SCREW M6-1 X 16
COVER BRACKET
LEFT ACCESS PANEL
LEFT UPPER COVER
RIVET NUT M6-1 X 15
COVER BRACKET
FLAT HEAD RIVET NUT M5-.8 X 13
-63-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Base Breakdown
703
701
702
707
706
705
703
702
708
709
714
710
711
705
710
711
707
708
701
710
713
710
711
712
713
712
REF PART #
713
DESCRIPTION
REF PART #
DESCRIPTION
701
702
703
705
706
707
708
P0675701
P0675702
P0675703
P0675705
P0675706
P0675707
P0675708
BASE SIDE PANEL
SPECIAL SCREW M6-1
RUBBER WASHER 6MM
BASE PANEL
709
710
711
712
713
714
P0675709
P0675710
P0675711
P0675712
P0675713
P0675714
LOCK NUT M6-1
HEX NUT M10-1.5
FOOT M10-1.5
HEX BOLT M6-1 X 16
BASE SUPPORT PANEL
HEX NUT M6-1
LOCK NUT M5-.8
CLAMPING HOOK
PHLP HD SCR M5-.8 X 10
-64-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Planer Table Breakdown
849
848
842
841
840
839
817
844
843
845
841
842
840
817
838
846
847
837
836
835
834
828
828
833
831
827
802
832
828
828
814
811
801
803
804
805
830
807
827
802
813
803
810
813
803
804
805
819
806
822
821
806
820
804
818
817
805
807
802
813
804
806
815
825
806
807
816
817
805
804
813
826
812
807
803
809
808
-65-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
Planer Table Parts List
DESCRIPTION
REF PART #
DESCRIPTION
REF PART #
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
825
P0675801
P0675802
P0675803
P0675804
P0675805
P0675806
P0675807
P0675808
P0675809
P0675810
P0675811
P0675812
P0675813
P0675814
P0675815
P0675816
P0675817
P0675818
P0675819
P0675820
P0675821
P0675822
P0675825
ELEVATION LEADSCREW RL
ELEVATION LEADSCREW
ROLL PIN 4 X 6
826
827
828
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
P0675826
P0675827
P0675828
P0675830
P0675831
P0675832
P0675833
P0675834
P0675835
P0675836
P0675837
P0675838
P0675839
P0675840
P0675841
P0675842
P0675843
P0675844
P0675845
P0675846
P0675847
P0675848
P0675849
TABLE ELEVATION CHAIN
PLANER TABLE GUIDE BLOCK
HEX BOLT M6-1 X 16
HEX NUT M10-1.5
COPPER TUBE
SUPPORT BRACKET
LEADSCREW SPROCKET
ROLL PIN 4 X 18
ACORN NUT M10-1.5
TAP SCREW M3.5 X 13
FLAT WASHER 10MM
INDICATOR BRACKET
DEPTH SCALE INDICATOR
FLAT WASHER 6MM
HEX BOLT M6-1 X 10
DEPTH SCALE
HANDWHEEL SHAFT
ROLL PIN 4 X 20
PLASTIC HANDLE
HANDWHEEL
SADDLE BRACKET
THREAD ROD TUBE
HANDWHEEL SCALE
LINKAGE
THICKNESSING TABLE
GUIDE AXLE
BUSHING
HEX BOLT M8-1.25 X 16
FLANGE NUT M8-1.25
FLAT WASHER 8MM
HANDLE BOLT M10 X 1.5 X 98
HEX BOLT M8-1.25 X 16
ADJUSTING ROD
SPIRAL SPRING DOWEL SLEEVE
DUST COLLECTOR ASSEMBLY
FLAT WASHER 6MM
LOCK NUT M6-1
BRUSH ASSEMBLY
FLAT HD SCR M6-1 X 14
DUST PORT BRACKET
DUST PORT
LOCK NUT M8-1.25
E-CLIP 10MM
Labels and Cosmetic Parts
REF PART #
DESCRIPTION
901
901
902
903
904
905
906
907
908
909
910
911
P0675901
P0675902
P0675903
P0675904
P0675905
P0675906
P0675907
P0675908
P0675909
P0675910
P0675911
CHANGING OPERATIONS LABEL
CUTTERHEAD GUARD LABEL
EAR PROTECTION LABEL
DISCONNECT POWER LABEL
MODEL NUMBER LABEL
902
GRIZZLY NAMEPLATE-LARGE
ELECTRICITY LABEL
MACHINE ID LABEL
911
GLASSES/RESPIRATOR LABEL
READ MANUAL LABEL
910
909
POLAR BEAR WHITE TOUCH-UP PAINT
907
903
904
908
Safety labels warn about machine hazards
and ways to prevent injury. The owner of
this machine MUST maintain the original
location and readability of the labels on the
machine. If any label is removed or becomes
unreadable, REPLACE that label before
using the machine again. Contact Grizzly at
new labels.
906
905
-66-
G0675 10" Jointer/Planer Combo Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name_____________________________________________________________________________
Street_____________________________________________________________________________
City _______________________ State_________________________ Zip _____________________
Phone #____________________ Email _________________________________________________
Model # ____________________ Order #_______________________ Serial #__________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop
better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
____ Advertisement
____ Card Deck
____ Friend
____ Website
____ Catalog
____ Other:
2. Which of the following magazines do you subscribe to?
____ Cabinetmaker & FDM
____ Family Handyman
____ Hand Loader
____ Popular Science
____ Popular Woodworking
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Rifle
____ Shop Notes
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Handy
____ Woodwork
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Woodworker West
____ Woodworker’s Journal
____ Other:
____ Model Airplane News
____ Old House Journal
____ Popular Mechanics
____ Shotgun News
____ Today’s Homeowner
____ Wood
3. What is your annual household income?
____ $20,000-$29,000
____ $30,000-$39,000
____ $40,000-$49,000
____ $70,000+
____ $50,000-$59,000
____ $60,000-$69,000
4. What is your age group?
____ 20-29
____ 30-39
____ 60-69
____ 40-49
____ 70+
____ 50-59
5. How long have you been a woodworker/metalworker?
____ 0-2 Years ____ 2-8 Years
____ 8-20 Years
____ 6-9
____20+ Years
____10+
6. How many of your machines or tools are Grizzly?
____ 0-2 ____ 3-5
7. Do you think your machine represents a good value?
8. Would you recommend Grizzly Industrial to a friend?
_____Yes
_____Yes
_____No
_____No
9. Would you allow us to use your name as a reference for Grizzly customers in your area?
Note: We never use names more than 3 times. _____Yes _____No
10. Comments:_____________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
FOLD ALONG DOTTED LINE
Send a Grizzly Catalog to a friend:
Name_______________________________
Street_______________________________
City______________State______Zip______
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-
ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the
carton. We will not accept any item back without this number. Proof of purchase must accompany the
merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|