28° CLIPPED HEAD
FRAMING NAILER
MODEL H6145
INSTRUCTION MANUAL
COPYRIGHT © FEBRUARY, 2005 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BL6905 PRINTED IN CHINA
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
ONLY ALLOW TRAINED AND
PROPERLY SUPERVISED PER-
SONNEL TO OPERATE MACHIN-
ERY. Make sure operation instruc-
tions are safe and clearly under-
stood.
13. ALWAYS DISCONNECT FROM
POWER SOURCE BEFORE
SERVICING MACHINERY. Make
sure switch is in OFF position
before reconnecting.
14. MAINTAIN MACHINERY WITH
CARE. Keep blades sharp and
clean for best and safest per-
formance. Follow instructions for
lubricating and changing acces-
sories.
7.
8.
9.
KEEP CHILDREN AND VISITORS
AWAY. Keep all children and visi-
tors a safe distance from the work
area.
MAKE WORKSHOP CHILD
PROOF. Use padlocks, master
switches, and remove start switch
keys.
15. REMOVE ADJUSTING KEYS
AND WRENCHES. Make a habit
of checking for keys and adjust-
ing wrenches before turning ON
machinery.
NEVER LEAVE WHEN MACHINE
IS RUNNING. Turn power OFF
and allow all moving parts to come
to a complete stop before leaving
machine unattended.
16. CHECK FOR DAMAGED PARTS
BEFORE USING MACHINERY.
Check for binding and align-
ment of parts, broken parts, part
mounting, loose bolts, and any
other conditions that may affect
machine operation. Repair or
replace damaged parts.
10. DO NOT USE IN DANGEROUS
ENVIRONMENTS. DO NOT use
machinery in damp, wet locations,
or where any flammable or noxious
fumes may exist.
17. USE
RECOMMENDED
11. KEEP WORK AREA CLEAN AND
WELL LIT. Clutter and dark shad-
ows may cause accidents.
ACCESSORIES. Refer to the
instruction manual for recom-
mended accessories. The use of
improper accessories may cause
risk of injury.
12. USE A GROUNDED EXTENSION
CORD
MACHINE
RATED FOR THE
AMPERAGE.
18. DO NOT FORCE MACHINERY.
Work at the speed for which
the machine or accessory was
designed.
Undersized cords overheat and
reduce voltage. Replace extension
cords if they become damaged. DO
NOT use extension cords for 220V
machinery.
-1-
H6145 28° Clipped Head Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety Instructions for Nailers
1. HAND INJURIES: Do not place your
hands near the nail point of entry. A
nail can deflect and tear through the
surface of the workpiece, puncturing
your hand or fingers.
5. HOSE USAGE: Make sure your
air hose is designed for the tool
in use, is in good condition, and
is long enough to reach your work
without stretching. However, an
overly long air hose in the work
area may be a tripping hazard.
2. COMBUSTIBLE GASES: Never
connect the nailer to pressurized
oxygen or other combustible gases
as a power source. Only use fil-
tered, lubricated, and regulated
compressed air.
6. OPERATING QUESTIONS: If you
are not sure about the intended
operation, stop using the nailer.
Seek formal training or research
books or magazines that special-
ize in pneumatic tools.
3. SAFE HANDLING: Never point the
nailer at others! Do not keep the
trigger pulled when loading fasten-
ers, carrying, or holding tool. Carry
the nailer only by the handle, never
by any other part. Do not carry the
nailer by the air hose. Disconnect
the nailer from the air hose when
going up and down ladders.
7. MAINTENANCE: Always discon-
nect air from the nailer when ser-
vicing or installing nails. During
maintenance, a nailer connected
to air may fire accidentally, caus-
ing serious personal injury.
8. COMPRESSED AIR RATING: Do
not connect the nailer to com-
pressed air that exceeds 120 PSI.
4. CLEANING: Never use gasoline or
other flammable liquids to clean the
nailer; vapors in the nailer will ignite
by a spark and cause it to explode.
9. CHECK VALVE: Do not use a
check valve or any other fitting that
allows air to remain in the tool.
-2-
H6145 28° Clipped Head Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating this nailer can propel
objects into the air, causing imme-
diate eye damage. To protect your-
self, always wear American National
Standards Institute (ANSI) approved
safety glasses or goggles when oper-
ating this equipment. In addition, this
nailer discharges at 85-90 decibels.
To protect your hearing, always wear
ANSI approved ear protection when
operating this nailer.
Never point this nailer at yourself or
another person! Always pay attention
to the direction this nailer is pointed.
Use this tool with respect and caution
to lessen the possibility of operator or
bystander injury. Ignoring this warning
may result in serious personal injury.
No list of safety guidelines can be
complete. Every shop environment
is different. Always consider safety
first, as it applies to your individual
working conditions. Use this and
other tools with caution and respect.
Failure to do so could result in seri-
ous personal injury, damage to
equipment or poor work results.
-3-
H6145 28° Clipped Head Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Foreword
Contact Info
We are proud to offer the Grizzly Model
H6145 28º Clipped Head Framing Nailer.
This model is part of a growing Grizzly
family of fine pneumatic tools. When used
according to the guidelines set forth in this
manual, you can expect years of trouble-
free, enjoyable operation and proof of
Grizzly’s commitment to customer satis-
faction.
If you have any comments regarding this
manual, please write to us at the following
address:
Grizzly Industrial, Inc.
C/O Technical Documentation
P.O. Box 2069
Bellingham, WA 98227-2069
Most importantly, we stand behind our
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
The Model H6145 is designed to toenail
into corners. This nailer is ideal for fram-
ing, pallet and crate assembly, deck, roof,
fencing, and sidewall sheathing construc-
tion. The Model H6145 features a 360°
exhaust port, comfort grip rubber handle,
and economical air consumption with low
noise.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
The specifications, details, and photo-
graphs in this manual represent the Model
H6145 as supplied when the manual was
prepared. However, owing to Grizzly’s pol-
icy of continuous improvement, changes
may be made at any time with no obliga-
tion on the part of Grizzly.
E-Mail: [email protected]
Machine Data
Nail Size ................7⁄64"-1⁄8" Shank Diameter
Nail Strip Angle......................................28º
Nail Length .......... 2"-3½"(Clipped Headed)
Magazine Capacity...................... 100 Nails
Air Inlet ...........................................¼" NPT
Weight .............................................81⁄3 lbs.
Operating Pressure .................. 70-120 PSI
Read the manual before operation.
Become familiar with this nailer, its
safety instructions, and its operation
before beginning any work. Serious
personal injury may result if safety or
operational information is not under-
stood or followed.
-4-
H6145 28° Clipped Head Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP
Inventory
Unpacking
Your Model H6145 left our warehouse in
a carefully packed box. If you discover
the nailer is damaged after you have
signed for delivery, please immediately
call Customer Service at (570) 546-9663
for advice.
After you remove the nailer case from the
box you should find the following.
Model H6145 Inventory (Figure 1)
A. 28° Clippled Head Framing Nailer..... 1
B. Safety Goggles ................................. 1
C. Oil....................................................... 1
D. Hex Wrench 3MM.............................. 1
E. Hex Wrench 4MM.............................. 1
F. Hex Wrench 5MM.............................. 1
G. Hex Wrench 6MM.............................. 1
Save the containers and all packing mate-
rials for possible inspection by the car-
rier or its agent. Otherwise, filing a freight
claim can be difficult.
When you are completely satisfied with
the condition of the shipment, you should
inventory the equipment.
A
B
C
G
F
E
D
Figure 1. Model H6145 inventory.
-5-
H6145 28° Clipped Head Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
Compressed Air
System
The Model H6145 is designed to be oper-
ated at 70-120 PSI using clean, dry, regu-
lated, compressed air. DO NOT exceed
the maximum operating pressure for
your model.
Before using your new nailer, regulate the
air pressure on your air compressor to the
minimum PSI for your model.
Exceeding the maximum permissible
operating pressure may cause the
nailer to explode, blowing metal frag-
ments in all directions. To protect
yourself from serious personal injury,
DO NOT allow your air compressor to
exceed the recommended pressure
when connected to this nailer!
An in-line filter/lubricator/regulator unit,
depicted in Figure 2, can be installed and
should be located as close to the nailer
as possible.
This filter/lubricator/regulator unit will
protect your tool from damaging water
build-up, allow you to adjust and maintain
constant air pressure to your tool, and
save you the inconvenience of having to
manually lubricate your tool every time
you use it.
Check the current Grizzly catalog for avail-
ability of this unit. If you plan on install-
ing a filter/lubricator/regulator unit in your
compressed air system, always follow the
connection instructions that come with
the unit.
Quick
Connector
Quick
Connector
Filter
Oiler
Air
Nailer
Compressor
Quick
Coupler
Regulator
Quick
Coupler
Air Hose
Figure 2. Filter/Lubricator/Regulator Unit.
-6-
H6145 28° Clipped Head Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Without pressing the trigger, depress
the safety yoke mechanism against a
scrap piece of wood that is clean and
free of any knots, nails, or other foreign
objects.
Safety Yoke
A safety yoke mechanism (bump fire) on
the nose of the nailer acts as a second-
ary safety device. When the trigger is
pressed, the nailer will not fire until the
safety yoke mechanism is depressed.
— If the nailer does not fire, then the
safety yoke mechanism is working
correctly.
Before you use your nailer for the first
time, check the safety yoke mechanism to
ensure proper function. To do this:
— If the nailer does fire when you
do this, immediately disconnect the
nailer from the air supply and call
Grizzly Technical Support at (570)
546-9663 for help.
1. DISCONNECT NAILER FROM THE
AIR SUPPLY!
— If the nailer fires when the trigger
is pulled, without the safety yoke
mechanism being depressed, then
the nailer is not working properly.
2. Make sure the magazine is empty and
contains no nails.
3. Make sure the trigger and the safety
yoke mechanism move up and down
without sticking.
— If either of these two conditions
develop after you have used your
nailer for a period of time, check the
lubrication of these mechanisms.
4. Connect the nailer to the air supply.
The safety yoke is
a
mechanical
device that can fail. Never rely on the
safety yoke mechanism as an excuse
to point the nailer at yourself or any
bystanders. Serious injury may occur.
-7-
H6145 28° Clipped Head Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
Loading
When replacing nails in your Model
H6145, follow these guidelines:
Diameter:7⁄64"-1⁄8
"
Length: 2"-31⁄2
Capacity: 100
Strip Angle: 28°
"
Figure 4. Loading nails into magazine.
NOTICE: A number of manufacturers'
nails may fit the H6145. However, for best
performance, we recommend you use
Grizzly nail Models G2421-G2430.
4. Slide the nails all the way down to the
nose of the nailer.
1. DISCONNECT NAILER FROM THE
AIR SUPPLY!
5. Release the catch lever. The pusher
slides forward until it rests against the
nail stick.
2. Gripping the nailer firmly, pull the mag-
azine pusher back and engage the
catch lever, as shown in Figure 3.
Operating
If you have not read the safety instruc-
tions in this manual, do not operate
the nailer.
Before you operate your nailer, place five
to six drops of the included oil into the
quick connect fitting where the nailer con-
nects to the air supply.
Pusher
Catch Lever
To operate your nailer:
Figure 3. Sliding pusher toward the catch
lever pusher.
1. Connect the air supply to the quick
connect fitting.
3. Insert a strip of nails, pointed-end down,
into the magazine as shown in
Figure 4.
2. To test for proper nail penetration, hold
the nailer perpendicular to the surface
of a piece of clean scrap wood that is
thick enough for the length of nails you
have loaded.
-8-
H6145 28° Clipped Head Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Pull the trigger and depress the safety
Adjusting Depth
yoke mechanism on your workpiece.
4. Before pulling the trigger, make sure
your free hand and other body parts
are positioned out of the way of a
potential path of a nail in case of
deflection.
The nose of the gun houses a depth adjust-
ment mechanism for setting the nail depth.
To adjust the depth:
1. DISCONNECT NAILER FROM THE
AIR SUPPLY!
Deflection is caused when grain
irregularities, knots or foreign objects
inside the wood cause the nail to
change its path, resulting in the
nail puncturing the surface of the
workpiece as shown in Figure 5.
2. If the nail is driven too far into the
workpiece, loosen the cap screw on
the safety nose with a 4mm wrench, as
shown in Figure 6.
Besides damaging your workpiece,
deflection can cause injury if your free
hand is securing the workpiece in the
location that the nail deflects.
Safety Nose
Safety Yoke
Cap Screw
Figure 6. Loosening cap screw for depth
adjustment.
3. Slide the safety nose (Figure 6) toward
the nailer body to drive nails deeper.
Slide the safety nose forward if the nail
goes too deep.
Figure 5. Example of nail deflection.
5. Pull the trigger. If the nail drove into the
wood far enough, continue with your
intended operations. If the nail either
went too far or not far enough, then go
to the Adjusting Depth section on this
page.
4. Tighten the safety nose cap screw
each time after making adjustments.
5. Connect to the air.
6. Pull the trigger and depress the safety
yoke mechanism on your workpiece to
test the depth adjustment.
-9-
H6145 28° Clipped Head Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
Single/Bump Fire
Mode
Clearing Jammed
Nails
The nailer is designed to fire one nail at a
time, or one after another, using the safety
yoke mechanism.
A jammed nail must be cleared before
using the nailer again. The two places
where a nail can get jammed are the maga-
zine and the discharge area.
To operate your nailer in single fire
mode:
To clear a jammed nail from the maga-
zine:
1. Depress the safety yoke mechanism
against the workpiece.
1. DISCONNECT NAILER FROM THE
AIR SUPPLY!
2. Pull the trigger, then remove your finger
2. Pull back and lock the magazine push-
from the trigger after the nail is driven.
er.
To operate your nailer in bump fire
mode:
3. Remove the nail stick.
4. Locate and remove the jammed nail
with needle nose pliers. Release the
catch lever and let the pusher slide to
front of the magazine.
1. Pull the trigger.
2. Press the safety yoke mechanism
against your workpiece and raise it
after the nail is driven.
To clear a jammed nail from the dis-
charge area:
3. Hold the trigger and repeat Step 2 to
drive more nails.
1. DISCONNECT NAILER FROM THE
AIR SUPPLY!
2. Pull back and lock the magazine push-
er in place.
3. Remove all nails from the magazine.
4. Locate the nail in the nailer nose, dis-
lodge the nail with a tool that will fit in
the slot on the underside of the nose.
5. Throw the damaged nail away and
insert a new nail stick that only con-
tains clean, undamaged nails. DO
NOT use dirty or damaged nails!
6. Release the catch lever and let the
pusher slide to the front of the maga-
zine.
-10-
H6145 28° Clipped Head Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
5. The top of the piston should now be
visible inside the cylinder, which is
housed in the head of the nailer.
Replacing Pistons/O-
Rings
6. Open the magazine.
If you use your nailer day in and day
out, repair pistons are cheap insurance
against wasted down time and lost profits,
in the event that a piston or piston shaft
becomes worn out.
7. Watch the discharge area and push
the top of the piston with your finger.
You will see the piston shaft slide
down the discharge area.
8. With a long flathead screwdriver or
similarly shaped tool, push the piston
shaft back inside the nailer until you
can grip the piston head and remove
it from the cylinder. (Be careful not to
scratch the discharge area when push-
ing the piston shaft with the screw-
driver.)
9. Place a new O-ring on the new piston
and apply a thin film of the nailer lubri-
cating oil on the O-ring.
Always disconnect air from nailer
whenever servicing! During mainte-
nance, a nailer connected to air may
fire accidentally, causing serious
personal injury!
10. Insert the new piston in the cylinder.
Make sure that the grooves on the
piston shaft line up with those on the
guide at the bottom of the cylinder.
The new piston should easily slide
into the cylinder. DO NOT force the
piston into the cylinder! If the piston
is not easily inserted, double-check the
alignment of the piston shaft with the
grooves on the guide.
To replace a piston:
1. DISCONNECT NAILER FROM THE
AIR SUPPLY!
11. After the piston is inserted correctly,
close the magazine. Replace the top
cap assembly and tighten the 4 cap
screws.
2. Remove all nails from the magazine
cartridge.
3. Remove the four cap screws on the
top of the nailer, near the exhaust
port.
12. For more assistance, or to install a
complete O-ring set, refer to the appro-
priate breakdown diagram in the back
of this manual.
4. Remove the top cap.
-11-
H6145 28° Clipped Head Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING & LUBRICATION
Lubricating
Cleaning
Special oil has been included with your
new Grizzly nailer to help maintain its
useful life. Place two to six drops of oil
in the nailer air inlet (as shown in Figure
7) before every use, or after 2 hours of
continuous use.
Use a good solvent to clean the nose
assembly of the nailer. Always be sure
that the nailer is dry before using it
again.
Do not allow dust, chips, sand, etc. into
the air connectors or into the body of the
nailer; this may result in leaks and dam-
age to the nailer and the air couplings.
Wipe off any excess oil near the nailer
exhaust to avoid dust build-up. When
the oil that was included with the nailer
has been completely used, replace with
Grizzly Model G2820 Pneumatic Tool Oil.
Another option to manual oiling would be
to install a lubricator in your air compres-
sor line. If your air compressor line already
has a lubricator, then regular lubrication
of your nailer will not be necessary. Just
make sure there is always oil in the lubri-
cator.
As mentioned before, the best option is
to install a filter/lubricator/regulator unit in
your air line.
Never use gasoline or other flamma-
ble liquids to clean this tool. Vapors
in the tool may ignite, causing the
tool to explode. Ignoring this warning
may lead to serious personal injury or
even death!
Figure 7. Lubricating nailer via air inlet.
-12-
H6145 28° Clipped Head Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
H6145 PARTS BREAKDOWN
-13-
H6145 28° Clipped Head Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
H6145 PARTS LIST
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
2
3
4
5
6
7
8
PH6145001
SPCL CAP SCR M8-1.25 X 30 48
PW02M
FLAT WASHER 5MM
ADJUSTING�NUT
SAFETY�YOKE
PH6145002
PH6145003
PH6145004
PH6145005
PSB06M
PLW03M
PH6145008
PSS07M
AIR DEFLECTOR
RUBBER WASHER
SPRING
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
PH6145049
PH6145050
PH6145051
PH6145052
PH6145053
PH6145054
PH6145055
PLW04M
PSB13M
PSB26M
PH6145059
PW03M
PLN02M
PH6145062
PSB18M
PLN01M
PS08M
PSB46M
PH6145067
PH6145068
PH6145069
PRP23M
PH6145071
PH6145072
PH6145073
PSB93M
SAFETY�NOSE
SPRING WIRE
COPPER�COLLAR
SAFETY�NOSE�CASE
O-RING 61.5 X 1.8
DRIVER�GUIDE
LOCK WASHER 8MM
CAP SCREW M8-1.25 X 30
CAP SCREW M6-1 X 12
MAGAZINE
FLAT WASHER 6MM
LOCK NUT M5-.8
DRIVE NAIL BAR
CAP SCREW M4-.7 X 8
LOCK NUT M4-.7
PHLP HD SCR M5-.8 X 12
CAP SCREW M4-.7 X 40
SAFETY�PIPE
SAFETY�PIPE�CASE
PIN�CASE
ROLL�PIN�4�X�44
PUSHER
PIN�3�X�20
PIN�5�X�20
CAP SCREW M3-.5 X 14
HEX NUT M3-.5
PIN�4�X�30
TORSION SPRING
SPRING CORE
PIN�5�X�12
CAP SCREW M6-1 X 25
LOCK WASHER 6MM
CYLINDER CORE
SET SCREW M5-.8 X 5
CYLINDER COVER
HEAD VALVE PISTON
SPRING SEAT
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
42
43
44
45
46
47
PH6145010
PH6145011
PH6145012
PH6145013
PH6145014
PH6145015
PH6145016
PH6145017
PH6145018
PH6145019
PH6145020
PH6145021
PH6145022
PH6145023
PH6145024
PH6145025
PH6145026
PH6145027
PH6145028
PH6145029
PH6145030
PH6145031
PH6145032
PH6145033
PH6145034
PH6145035
PH6145036
PH6145037
PH6145038
PH6145039
PH6145040
PH6145042
PRP02M
COMPRESSION�SPRING
O-RING�56.7�X�3
COLLAR
O-RING 42.3 X 5
PISTON
O-RING 57.5 X 3
O-RING 88 X 3
FIXED�RING
SEALING�RING
CYLINDER
BUMPER
GASKET
BODY
RUBBER�WASHER
TRIGGER�VALVE�SEAT
O-RING 15 X 2.65
O-RING 17 X 1.5
TRIGGER�VALVE�GUIDE
O-RING 6.2 X 1.8
O-RING 6.4 X 2
O-RING 9 X 1.8
SWITCH�SPRING
SWITCH�PIPE
PN07M
PH6145076
PH6145077
PH6145078
PH6145079
PH6145080
PH6145081
PSB38M
PW02M
PH6145084
PLN02M
RELEASE LATCH
TORSION SPRING
CAP SCREW M5-.8 X 25
FLAT WASHER 5MM
FIXED SEAT
LOCK NUT M5-.8
RUBBER HANDLE CASE
GASKET
O-RING 2.5 X 1.5
O-RING 20.3 X 2.3
SWITCH�SEAT
TRIGGER�PIN
TRIGGER
PH6145086
PH6145087
PH6145088
PSB15M
SAFETY�SPACER
ROLL�PIN�3�X�16�
SAFETY�GUIDE
PIN�3�X�25
END CAP
CAP SCREW M5-.8 X 20
LOCK WASHER 5MM
1/4" NPT MALE CONNECT
AIR PLUG COVER
FLAT WASHER 5MM
PH6145044
PH6145045
PH6145046
PSB03M
PLW01M
PH6145091
PH6145092
PW02M
COMPRESSION�SPRING
CAP SCREW M5-.8 X 8
-14-
H6145 28° Clipped Head Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
CAUSE
PROBLEM
ACTION
Air leaking at trigger valve
area.
1. O-rings in trigger valve
housing are damaged.
1. O-rings must be replaced
& operation of safety
yoke must be checked.
Air leaking between hous-
ing and hose.
1. Loose screws in housing.
2. Damaged O-ring.
3. Loose air fitting.
1. Tighten screws.
2. Replace O-ring.
3. Tighten air fitting & use
teflon tape
Air leaking between hous-
ing and cap assembly.
1. Damaged seal.
1. Air leaks.
1. Replace damaged seals.
Tool skips nails while dis-
charging.
1. Tighten screws and fit-
tings.
2. Dirt in nose.
2. Clean nose.
3. Dirt or damage prevents
nails from moving freely in
magazine.
3. Clean magazine and
inspect/repair damage.
4. Inadequate air flow to tool. 4. Check fitting, hose, com-
pressor & air pressure.
5. Worn O-ring on piston or
lack of lubrication.
5. Replace piston O-ring.
Lubricate.
6. Damaged O-rings on trig-
ger valve.
6. Replace trigger valve O-
rings.
7. Worn bumper.
8. Cap seal leaking.
7. Replace bumper.
8. Replace cap seal.
Tool runs slowly or has a
loss of power.
1. Nailer is not sufficiently
lubricated.
2. Broken spring in cap
assembly.
1. Lubricate nailer.
2. Replace spring.
3. Exhaust port in cap is
blocked.
3. Clean or replace dam-
aged internal parts.
Fasteners frequently jam
the nailer.
1. Nails are the wrong size.
2. Nails are bent or dirty.
1. Use correct nails.
2. Use undamaged, clean
nails.
3. Magazine or nose screws
are loose.
3. Tighten magazine.
4. Driver or driver guide are
worn or damaged.
4. Replace worn or dam-
aged parts.
5. Nails are wrong angle.
5. Use correct angle nails.
Nailer does not fire.
1. Nail is jammed in maga-
zine or discharge area.
2. Piston shaft is damaged.
3. Air pressure too low.
1. Clear nailer magazine or
discharge area.
2. Replace piston shaft.
3. Check/increase air pres-
sure.
-15-
H6145 28° Clipped Head Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of
maintenance. This is Grizzly’s sole written warranty and any and all warranties that may
be implied by law, including any merchantability or fitness, for any particular purpose, are
hereby limited to the duration of this written warranty. We do not warrant or represent that
the merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental,
contingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Authorization Number,” which must be clearly posted on
the outside as well as the inside of the carton. We will not accept any item back without this
number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they
constantly strive to achieve better quality equipment. We make every effort to ensure that
our products meet high quality and durability standards and we hope you never need to
use this warranty.
Please feel free to write or call us if you have any questions about the machine or the
manual.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
Thank you again for your business and continued support. We hope to serve you again
soon!
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name_________________________________________________________________________
Street ________________________________________________________________________
City____________________State________Zip_________
Phone Number____________E-Mail___________________FAX ____________
Model # H6145 28° Clipped Head Framing Nailer Serial#_______________Order #________
The following information is given on a voluntary basis. It will be used for marketing purposes to help
us develop better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
___Advertisement
9. How many of the machines checked above are
Grizzly? __________________________________
___Friend
___Card Deck
___Catalog
___World Wide Web
___Other__________________________
10. Which portable/hand held power tools do you own?
Check all that apply.
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
2. What is your annual household income?
___$20,000-$29,999 ___$60,000-$69,999
___$30,000-$39,999 ___$70,000-$79,999
___$40,000-$49,999 ___$80,000-$89,999
___$50,000-$59,999 ___$90,000 +
___Miter Saw
Other_________________________________
3. What is your age group?
11. What machines/supplies would you like Grizzly
Industrial to carry?
___20-29
___30-39
___40-49
___50-59
___60-69
___70 +
________________________________________
________________________________________
________________________________________
________________________________________
4. How long have you been a woodworker?
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
12. What new accessories would you like Grizzly
Industrial to carry?
5. How would you rank your woodworking skills?
________________________________________
________________________________________
________________________________________
________________________________________
___Simple
___Advanced
___Intermediate
___Master Craftsman
6. What stationary woodworking tools do you own?
Check all that apply.
13. What other companies do you purchase your tools
and supplies from?
___Air Compressor
___Band Saw
___Panel Saw
___Planer
________________________________________
________________________________________
________________________________________
________________________________________
___Drill Press
___Power Feeder
___Radial Arm Saw
___Shaper
___Jointer
___Lathe
___Drum Sander
___Dust Collector
___Spindle Sander
___Table Saw
14. Do you think your purchase represents good
value?
___Mortiser
___Wide Belt Sander
___Horiz.Boring Machine
___Vacuum Veneer Press
___Yes
___No
___Other______________________________
15. Would you recommend Grizzly to a friend?
___Yes ___No
7. How many of your woodworking machines are
Grizzly? _______________________________
16. Would you allow us to use your name as a refer-
ence for Grizzly customers in your area? Note: We
never use names more than three times.
8. Which benchtop tools do you own? Check all
that apply.
___Yes
___No
___1"x42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
17.Comments:________________________________
_________________________________________
_________________________________________
_________________________________________
___8" Table Saw
___Scroll Saw
___8" - 10" Bandsaw
___Disc/Belt Sander
___Spindle/Belt Sander ___Mini Jointer
___10"-12"Thickness Planer
Other____________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
Send a Grizzly Catalog to a friend:
Name________________________________
Street________________________________
City______________State______Zip_______
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
|