MEAT GRINDER
MODEL H6248
INSTRUCTION MANUAL
COPYRIGHT © SEPTEMBER, 2004 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#PC6576 PRINTED IN CHINA
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazard-
ous conditions. This manual uses a series of symbols and signal words which
are intended to convey the level of importance of the safety messages. The
progression of symbols is described below. Remember that safety messages by
themselves do not eliminate danger and are not a substitute for proper accident
prevention measures.
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.
This symbol is used to alert the user to useful infor-
NOTICE
mation about proper operation of the equipment.
Safety Instructions for Machinery
4.
5.
WEAR PROPER APPAREL. DO
NOT wear loose clothing, gloves,
neckties, rings, or jewelry which
may get caught in moving parts.
Wear protective hair covering to
contain long hair and wear non-slip
footwear.
1.
2.
READ THROUGH THE ENTIRE
MANUAL BEFORE STARTING
MACHINERY. Machinery presents
serious injury hazards to untrained
users.
MAKE SURE ALL GUARDS ARE
IN THEIR CORRECT PLACE AND
WORK CORRECTLY BEFORE
USING MACHINERY. NEVER
OPERATE MACHINE WITHOUT
GUARDS.
NEVER OPERATE MACHINERY
WHEN TIRED, OR UNDER THE
INFLUENCE OF DRUGS OR
ALCOHOL. Be mentally alert at all
times when running machinery.
3.
ALWAYS USE ANSI APPROVED
SAFETY
GLASSES
WHEN
OPERATING MACHINERY.
-1-
Model H6248 Meat Grinder
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
ONLY ALLOW TRAINED AND
PROPERLY SUPERVISED
PERSONNEL TO OPERATE
MACHINERY. Make sure opera-
tion instructions are safe and
clearly understood.
13. ALWAYS DISCONNECT FROM
POWER SOURCE BEFORE
SERVICING MACHINERY. Make
sure switch is in OFF position
before reconnecting.
14. MAINTAIN MACHINERY WITH
CARE. Keep blades sharp and
clean for best and safest perfor-
mance. Follow instructions for
lubricating and changing acces-
sories.
7.
8.
9.
KEEPCHILDRENANDVISITORS
AWAY. Keep all children and visi-
tors a safe distance from the work
area.
MAKE WORKSHOP CHILD
PROOF. Use padlocks, master
switches, and remove start switch
keys.
15. REMOVE ADJUSTING KEYS
AND WRENCHES. Make a habit
of checking for keys and adjust-
ing wrenches before turning ON
machinery.
NEVER LEAVE WHEN MACHINE
IS RUNNING. Turn power OFF
and allow all moving parts to come
to a complete stop before leaving
machine unattended.
16. CHECK FOR DAMAGED PARTS
BEFORE USING MACHINERY.
Check for binding and alignment
of parts, broken parts, part mount-
ing, loose bolts, and any other
conditions that may affect machine
operation. Repair or replace dam-
aged parts.
10. DO NOT USE IN DANGEROUS
ENVIRONMENTS. DO NOT use
machinery in damp, wet locations,
or where any flammable or nox-
ious fumes may exist.
17. USE
RECOMMENDED
11. KEEP WORK AREA CLEAN AND
WELL LIT. Clutter and dark shad-
ows may cause accidents.
ACCESSORIES. Refer to the
instruction manual for recom-
mended accessories. The use of
improper accessories may cause
risk of injury.
12. USE A GROUNDED EXTENSION
CORD
MACHINE
RATED FOR THE
AMPERAGE.
18. DO NOT FORCE MACHINERY.
Work at the speed for which
the machine or accessory was
designed.
Undersized cords overheat and
reduce voltage. Replace exten-
sion cords if they become dam-
aged. DO NOT use extension
cords for 220V machinery.
-2-
Model H6248 Meat Grinder
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety Instructions For
Meat Grinders
1. READ THIS MANUAL: This manu-
5. LOOSE CLOTHING: DO NOT wear
al contains proper operating instruc-
tions for this machine.
loose clothing while operating this
machine. Tie back long hair.
2. ALWAYS CLEAN AND SANITIZE
ALL PARTS THAT COME IN CON-
TACT WITH MEAT DURING PRO-
CESSING.
6. SHARP SURFACES: DO NOT
place hands near, or in contact with,
cutting surfaces during operation.
7. MACHINE INSPECTIONS: Perform
machine inspections and mainte-
nance service promptly as required.
3. DISCONNECT POWER: Always
disconnect the machine from the
power source before cleaning,
changing attachments or when per-
forming maintenance of any kind on
this tool.
8. ATTEND TO YOUR MACHINE:
Never walk away and leave the
machine running.
4. MATERIAL FEED: Always feed
material evenly and smoothly. DO
NOT put any utensil other than
meat pusher into grinder.
9. KEEP BLADES SHARP: Replace
or sharpen blade as needed.
10. TEST RUN: Always test run the
machine before starting any work.
Bacteria from raw meat has been
frequently linked to illness and even
death! Describing proper meat han-
dling techniques outside of cleaning
the meat grinder is beyond the scope
of this manual. If you are unclear
about sanitary meat handling practic-
es, contact your local Board of Health
or the USDA to research the proper
methods of meat handling.
No list of safety guidelines can be
complete. Every shop environment
is different. Always consider safety
first, as it applies to your individual
working conditions. Use this and
other machinery with caution and
respect. Failure to do so could result
in serious personal injury, damage
to equipment or poor work results.
Model H6248 Meat Grinder
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Foreword
Contact Info
If you have any comments regarding this
manual, please write to us at the following
address:
We are proud to offer the Grizzly Model
H6248 Meat Grinder. This model is part of
a growing Grizzly family of fine power tools.
When used according to the guidelines set
forth in this manual, you can expect years
of trouble-free, enjoyable operation and
proof of Grizzly’s commitment to customer
satisfaction.
Grizzly Industrial, Inc.
C/O Technical Documentation
P.O. Box 2069
Bellingham, WA 98227-2069
Most importantly, we stand behind our
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
The Model H6248 features a powerful
1000 Watt grinder, fine, medium and
course dies, and sausage stuffing and
kubbe attachments.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
It is our pleasure to provide this manual
with the Model H6248. It was written
to encourage safety considerations and
guide you through general operating pro-
cedures and maintenance. This manual
represents our effort to produce the best
documentation possible.
E-Mail: [email protected]
The specifications, details, and photo-
graphs in this manual represent the Model
H6248 as supplied when the manual was
prepared. However, owing to Grizzly’s pol-
icy of continuous improvement, changes
may be made at any time with no obliga-
tion on the part of Grizzly.
Machine Data
Motor ..............................110V, 1000 Watts
Amp Draw.................................... 1.0 Amps
Dimensions ....................17 x 14-1/2 x 6-1/2
Net Weight.....................................13.2 lbs.
Read the manual before operation.
Become familiar with this machine, its
safety instructions, and its operation
before beginning any work. Serious
personal injury may result if safety or
operational information is not under-
stood or followed.
-4-
Model H6248 Meat Grinder
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP
Unpacking
Inventory
After you have unpacked the carton you
should find the following.
Your machine left our warehouse in a
carefully packed crate or box. If you dis-
cover the machine is damaged after you
have signed for delivery, please immedi-
ately call Customer Service at (570) 546-
9663 for advice.
Figure 1. Model H6248 Inventory.
A. Grinder Motor Housing ........................ 1
B. Meat Pusher......................................... 1
C. Hopper ................................................. 1
D. Grinding Head...................................... 1
E. Sausage Stuffer Cones........................ 3
F. Kubbe Attachments.............................. 2
G. Cutting Plates ...................................... 3
Save the containers and all packing mate-
rials for possible inspection by the car-
rier or its agent. Otherwise, filing a freight
claim can be difficult.
When you are completely satisfied with
the condition of the shipment, you should
inventory the equipment.
E
A
F
G
C
D
B
Figure 1. Model H6248 inventory
Model H6248 Meat Grinder
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling Grinding
Head
5. Carefully slide the cutting blade on
the square shaft on the front of the
feed screw (Figure 3).
1. Loosen the locking knob, and remove
the grinding head assembly from the
grinder motor housing.
2. Unscrew the lock ring and remove the
cutting plate, cutting blade and feed
screw. Thoroughly sanitize the grind-
er head, cutting plates, cutting blade,
feed screw, lock ring and attachments
(refer to Proper Sanitization on page
9 for information).
Figure 3. Cutting blade installation
3. Before proceeding with assembly,
wipe down outside surface of grinder
motor housing with a sanitized cloth.
6. Choose one of the three cutting
plates.
7. Slide the cutting plate over the shaft
and align with the locking pin located
at the bottom of the barrel of the
grinder head. ( Figure 4).
4. After cleaning, assemble the grinder
head by inserting the feed screw into
the barrel of the grinder head with the
longer end of the hex shaft projecting
through the back of the grinder head
barrel (Figure 2).
locking pin
Barrel
Feed Screw
Throat
Figure 4. Cutting plate installation
Figure 2. Feed screw installation
8. Screw the lock ring on to the barrel
clockwise to secure the assembly.
-6-
Model H6248 Meat Grinder
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Grinding
Head Assembly
Controls
1. With the throat of the grinder head
pointing up, insert the hex shaft into
the grinder motor housing.
ON/OFF and Circuit Breaker Buttons
(Figure 6):
2. Tighten the locking knob to secure the
grinding head.
3. Set the hopper onto the grinder head
throat (refer to the Parts Breakdown
on page 11 for more detail).
Attachments
Figure 6. Button location
1. To install a sausage stuffing cone,
remove the lock ring, cutting die and
cutting blade. Note–Attachments
require the removal of the cutting
plate and cutting blade to function
properly.
1. Press the ON button to turn the motor
ON.
2. Press the OFF button to turn the
motor OFF.
3. The OFF button doubles as the
REVERSE button. WAIT UNTIL
GRINDER HAS COME TO A COM-
PLETE STOP BEFORE REVERSING.
The motor will only turn in reverse
as long as the REVERSE button is
pressed.
2. Select a sausage stuffing cone and
insert it through the back of the cone
flange and lock ring (Figure 5).
4. The built in circuit breaker will trip if the
grinder jams or is overloaded by forc-
ing too much product through at one
time. You will need to press the CIR-
CUIT BREAKER to reset the motor
after the jam is cleared.
Figure 5. Sausage stuffing cone installation
3. Tighten the lock ring clockwise onto
the grinder head.
4. For the Kubbe attachment, follow
steps 1-3.
Model H6248 Meat Grinder
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
If a jam occurs:
Grinding
1. Turn off the grinder and allow it to
come to a complete stop. Press the
REVERSE button once or twice to
attempt to free the jam. If that frees the
jam proceed.
The Model H6248 is designed for meat
processing. DO NOT attempt to grind bone
or hard foods like nuts or fibrous foods like
ginger.
If not:
1. Make sure all meat grinding parts are
properly sanitized before beginning
(Refer to the Cleaning section on
page 9 for more information).
1. UNPLUG THE GRINDER FROM THE
POWER SOURCE!
2. Disassemble the grinding head and
remove the material jamming the cut-
ter or feed screw.
2. Install the fine, medium or course cut-
ting plate.
3. Cut all meats into sizes that will easily
3. Assemble the grinder head, connect
to the power source and depress the
CIRCUIT BREAKER button to reset
the motor.
fit into the hopper throat.
4.
Plug in the grinder and turn it ON.
5. Use meat pusher to push meat down
to the feed screw. DO NOT use any
other utensil or stick fingers down the
hopper throat.
4. Turn the motor ON and proceed with
grinding.
6. Feed the meat into the grinder steadi-
ly. Do not force it or cause the motor
to labor.
Remove the grinder plug from the
outlet before clearing any jams.
The meat grinder can easily grind
your fingers. Never use your fingers
to push meat into the grinder. Always
use the provided meat pusher.
-8-
Model H6248 Meat Grinder
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING & LUBRICATION
Proper Sanitation
2.
Prepare the sink. Wash and scrub
all sink compartments with dish soap
and hot water. Rinse these compart-
ments thoroughly.
All surfaces and working parts that have
been exposed to meat must be properly
sanitized before and after each use.
3.
4.
Fill a sink with soapy water, sub-
merge the item and scrub the entire
surface thoroughly.
Dishwashers are a good option because
they sanitize with heat. If a dishwasher is
not available, there are chemical sanitizers
on the market that serve the same function.
When using chemical sanitizers, make sure
they are designed to do the job, and strictly
follow the manufacturer’s recommenda-
tions for proper use.
Using hot water, rinse the newly
cleaned item in the empty compart-
ment, until all visible suds have been
removed. Repeat this process for all
of the items that need to be sani-
tized. If the soapy water starts to get
hazy, drain and rinse the sink, then
fill with more soapy water.
NOTICE
The items are now ready to be sanitized.
Some sanitizers require direct applications,
while others are designed to be diluted
in water and used to soak the item for a
specified period of time. The best method
for choosing a chemical sanitizer is to do
the research and determine which product
is best for your particular situation.
Chlorine Bleach can discolor alumi-
num parts. Study the ingredients
of detergents and sanitizers before
cleaning aluminum parts. (Hopper,
grinding head and lock ring) We
recommend using a chemical sani-
tizer for these parts specifically
designed for sanitizing aluminum.
One simple sanitizer that can be used for
many applications is regular bleach. To
use bleach as a sanitizer, wash, scrub,
and rinse your sink. For all non-porous
surfaces (except aluminum) fill the sink
with one tablespoon of bleach per gallon of
cool water. Do not use bleach that contains
odor masking agents or surfactants. These
have not been proven effective for this type
of sanitation. Submerge each item for two
minutes. For large items, submerge each
side for the specified amount of time until
you have covered the entire area. Allow
to air dry. Do not rinse these items after
sanitation!
Proper sanitation with chemical sanitizers
requires a process before the actual sani-
tizer is applied.
The following is an effective method to pre-
pare an item for sanitation:
1.
Gather all the items that need to be
cleaned. Remove the largest par-
ticles of meat and place into a proper
garbage container. Rinse all items
to remove as many of the leftover
particles as possible. Set the items
aside.
Model H6248 Meat Grinder
Download from Www.Somanuals.com. All Manuals Search And Download.
-9-
Cleaning the motor housing:
Lubrication:
1. UNPLUG THE MOTOR FROM THE
POWER SOURCE!
The Model H6248 requires very little lubri-
cation. The following steps on the grinder
head parts will keep them moving freely
and keep them from oxidizing.
2. Wipe down the exterior surface of the
motor with a cloth soaked in a sanitiz-
ing solution. DO NOT submerge the
motor in water!
1. Be sure to use
a
non-vegetable
base, food service lubricant on this
machine.
2. Place a small drop of lubricant on the
front and rear flats on the shaft of the
feed screw.
3. Apply a thin film of lubricant to the cut-
ter dies to prevent them from rusting.
Reduce the risk of electrocution by
keeping all connections dry. DO NOT
touch plugs with wet hands. DO NOT
submerge in water. Failure to follow
these warning could result in seri-
ous injury.
!
Unplug the meat grinder before
performing any cleaning or mainte-
nance.
-10-
Model H6248 Meat Grinder
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Breakdown
�
�
��
��
��
��
�
�
�
�������������������
�
�
�
�
DESCRIPTION
REF
PART #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
PH6248001
PH6248002
PH6248003
PH6248004
PH6248005
PH6248006
PH6248007
PH6248008
PH6248009
PH6248010
PH6248011
PH6248012
PH6248013
PH6248014
PH6248015
PH6248016
PH6248017
MEAT PUSHER
HOPPER
GRINDER MOTOR HOUSING
GRINDING HEAD
FEED SCREW
KUBBE ATTACHMENT-REAR
KUBBE ATTACHMENT-FRONT
CUTTING PLATE-COURSE
LOCK RING
CUTTING PLATE-FINE
CUTTING PLATE-MEDIUM
CUTTING BLADE
LOCKING KNOB M10-1.5 X 30
SAUSAGE STUFFER CONE-SM
SAUSAGE STUFFER CONE-MD
SAUSAGE STUFFER CONE-LG
SAUSAGE STUFFER FLANGE
Model H6248 Meat Grinder
Download from Www.Somanuals.com. All Manuals Search And Download.
-11-
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of
maintenance. This is Grizzly’s sole written warranty and any and all warranties that may
be implied by law, including any merchantability or fitness, for any particular purpose, are
hereby limited to the duration of this written warranty. We do not warrant or represent that
the merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental,
contingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Authorization Number,” which must be clearly posted on
the outside as well as the inside of the carton. We will not accept any item back without this
number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they
constantly strive to achieve better quality equipment. We make every effort to ensure that
our products meet high quality and durability standards and we hope you never need to
use this warranty.
Please feel free to write or call us if you have any questions about the machine or the
manual.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
Thank you again for your business and continued support. We hope to serve you again
soon!
-12-
Model H6248 Meat Grinder
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name_________________________________________________________________________
Street ________________________________________________________________________
City____________________State________Zip_________
Phone Number____________E-Mail___________________FAX ____________
Model # H6248 Meat Grinder Serial#________________Order #____________
The following information is given on a voluntary basis. It will be used for marketing purposes to help
us develop better products and services. Of course, all information is strictly confidential.
9. How many of the machines checked above are
Grizzly? __________________________________
1. How did you learn about us?
___Advertisement
___Friend
___Catalog
___World Wide Web
___Other__________________________
___Card Deck
10. Which portable/hand held power tools do you own?
Check all that apply.
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
2. What is your annual household income?
___$20,000-$29,999 ___$60,000-$69,999
___$30,000-$39,999 ___$70,000-$79,999
___$40,000-$49,999 ___$80,000-$89,999
___$50,000-$59,999 ___$90,000 +
___Miter Saw
Other_________________________________
3. What is your age group?
11. What machines/supplies would you like Grizzly
Industrial to carry?
___20-29
___30-39
___40-49
___50-59
___60-69
___70 +
________________________________________
________________________________________
________________________________________
________________________________________
4. How long have you been a woodworker?
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
12. What new accessories would you like Grizzly
Industrial to carry?
5. How would you rank your woodworking skills?
________________________________________
________________________________________
________________________________________
________________________________________
___Simple
___Advanced
___Intermediate
___Master Craftsman
6. What stationary woodworking tools do you own?
Check all that apply.
13. What other companies do you purchase your tools
and supplies from?
___Air Compressor
___Band Saw
___Panel Saw
___Planer
________________________________________
________________________________________
________________________________________
________________________________________
___Drill Press
___Power Feeder
___Radial Arm Saw
___Shaper
___Jointer
___Lathe
___Drum Sander
___Dust Collector
___Spindle Sander
___Table Saw
14. Do you think your purchase represents good
value?
___Mortiser
___Wide Belt Sander
___Horiz.Boring Machine
___Vacuum Veneer Press
___Yes
___No
___Other______________________________
15. Would you recommend Grizzly to a friend?
___Yes ___No
7. How many of your woodworking machines are
Grizzly? _______________________________
16. Would you allow us to use your name as a refer-
ence for Grizzly customers in your area? Note: We
never use names more than three times.
8. Which benchtop tools do you own? Check all
that apply.
___Yes
___No
___1"x42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
17.Comments:________________________________
_________________________________________
_________________________________________
_________________________________________
___8" Table Saw
___Scroll Saw
___8" - 10" Bandsaw
___Disc/Belt Sander
___Spindle/Belt Sander ___Mini Jointer
___10"-12"Thickness Planer ___
Other____________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
Send a Grizzly Catalog to a friend:
Name________________________________
Street________________________________
City______________State______Zip_______
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
|