Grizzly Lathe ML 33607 User Manual

MODEL G0462

WOOD LATHE w/DIGITAL READOUT

OWNER'S MANUAL

(For models manufactured since 11/14)

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

FOR MODELS MANUFACTURED SINCE 11/14 #TS12792 PRINTED IN CHINA

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

INTRODUCTION............................................... 2

SECTION 5: ACCESSORIES......................... 31

Machine Description ...................................... 2

Contact Info.................................................... 2

Manual Accuracy ........................................... 2

Identification................................................... 3

Machine Data Sheet ...................................... 4

SECTION 6: MAINTENANCE......................... 33

Schedule...................................................... 33

Cleaning....................................................... 33

Lathe Bed..................................................... 33

Tailstock....................................................... 33

Lubrication ................................................... 33

Motor Shaft Lubrication.............................................34

SECTION 1: SAFETY....................................... 6

Safety Instructions for Machinery .................. 6

Additional Safety for Wood Lathes ................ 8

SECTION 7: SERVICE ................................... 35

Troubleshooting ........................................... 35

Motor & Electrical......................................................35

Aligning Centers........................................... 37

Replacing V-Belt.......................................... 37

SECTION 2: POWER SUPPLY........................ 9

Availability ...................................................................9

Full-Load Current Rating.............................................9

110V Circuit Requirements .........................................9

Grounding & Plug Requirements ..............................10

Extension Cords........................................................10

SECTION 8: WIRING...................................... 38

Wiring Safety Instructions............................ 38

Electrical Components & Wiring Diagram ... 39

SECTION 3: SETUP ....................................... 11

Unpacking.................................................... 11

Needed for Setup......................................... 11

Inventory ...................................................... 11

Cleanup........................................................ 13

Site Considerations...................................... 14

Anchoring to Floor ....................................... 15

Anchoring to Concrete Floors ...................................15

Assembly ..................................................... 15

Test Run ...................................................... 16

SECTION 9: PARTS....................................... 40

Main ............................................................. 40

Machine Labels............................................ 42

WARRANTY AND RETURNS ........................ 45

SECTION 4: OPERATIONS ........................... 18

Operation Overview..................................... 18

Stock Inspection & Requirements................ 19

Adjusting Head............................................. 19

Adjusting Tailstock Position......................... 20

Adjusting Tool Rest...................................... 21

Installing/Removing Spur Center................. 22

Installing Spur Center................................................22

Removing Spur Center..............................................22

Installing/Removing Live Center.................. 23

Installing Live Center.................................................23

Removing Live Center...............................................23

Installing/Removing Faceplate..................... 24

Adjusting Spindle Speed.............................. 25

Selecting Turning Tools............................... 26

Spindle Turning............................................ 27

Spindle Turning Tips .................................................28

Faceplate Turning........................................ 29

Attaching Faceplate to Spindle .................................29

Using a Backing Block ..............................................29

Outboard Turning......................................... 30

Sanding/Finishing Using the Lathe.............. 30

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION

Machine Description

Manual Accuracy

We are proud to provide a high-quality owner’s

manual with your new machine!

The Model G0462 Wood Lathe is designed to turn

wood stock so the operator can remove material

with a hand-held cutting tool or chisel.

We made every effort to be exact with the instruc-

tions, specifications, drawings, and photographs

in this manual. Sometimes we make mistakes, but

our policy of continuous improvement also means

that sometimes the machine you receive is

slightly different than shown in the manual.

The variable speed allows for infinite spindle

speed adjustment from 600–2400 RPM, and the

digital readout provides a precise reading of the

current spindle speed.

The ability to rotate and move the head allows for

turning workpieces with diameters larger than 12"

on the outboard side of the lathe.

If you find this to be the case, and the difference

between the manual and machine leaves you

confused or unsure about something, check our

website for an updated version. We post current

manuals and manual updates for free on our web-

site at www.grizzly.com.

The heavy-duty tailstock provides substantial

stability when mounting the workpiece between

centers.

Alternatively, you can call our Technical Support

for help. Before calling, make sure you write down

the Manufacture Date and Serial Number from

the machine ID label (see below). This information

is required for us to provide proper tech support,

and it helps us determine if updated documenta-

tion is available for your machine.

Contact Info

We stand behind our machines. If you have

any questions or need help, use the information

below to contact us. Before contacting, please get

the serial number and manufacture date of your

machine. This will help us help you faster.

Grizzly Technical Support

1203 Lycoming Mall Circle

Muncy, PA 17756

Manufacture Date

Serial Number

Phone: (570) 546-9663

Email: techsupport@grizzly.com

We want your feedback on this manual. What did

you like about it? Where could it be improved?

Please take a few minutes to give us feedback.

Grizzly Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Email: manuals@grizzly.com

-2-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

Identification

Spindle

& Spur Center

Tailstock

Lock Lever

Digital

Tailstock

Handwheel

Readout

Live

Center

Tool Rest

Motor

Bed

Head

Lock Lever

Variable

Speed Lever

Power

Switch

Tool Rest Base

w/Pivot Arm

Head Pivot

Lock Pin

Figure 1. Model G0462 identification.

-3-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

Machine Data Sheet

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901

MODEL G0462 WOOD LATHE WITH DIGITAL READOUT

Product Dimensions:

Weight.............................................................................................................................................................. 287 lbs.

Width (side-to-side) x Depth (front-to-back) x Height..................................................................... 72-1/2 x 19 x 48 in.

Footprint (Length x Width)..................................................................................................................... 54 x 13-3/4 in.

Shipping Dimensions:

Type..................................................................................................................................................... Cardboard Box

Content........................................................................................................................................................... Machine

Weight.............................................................................................................................................................. 354 lbs.

Length x Width x Height....................................................................................................................... 18 x 64 x 20 in.

Must Ship Upright................................................................................................................................................... Yes

Electrical:

Power Requirement........................................................................................................... 110V, Single-Phase, 60 Hz

Prewired Voltage.................................................................................................................................................. 110V

Full-Load Current Rating........................................................................................................................................ 14A

Minimum Circuit Size.............................................................................................................................................. 20A

Connection Type....................................................................................................................................... Cord & Plug

Power Cord Included.............................................................................................................................................. Yes

Power Cord Length................................................................................................................................................. 8 ft.

Power Cord Gauge......................................................................................................................................... 16 AWG

Plug Included.......................................................................................................................................................... Yes

Included Plug Type................................................................................................................................................ 5-15

Switch Type.................................................................................................. Paddle Safety Switch w/Removable Key

Motors:

Main

Type................................................................................................................. TEFC Capacitor-Start Induction

Horsepower................................................................................................................................................ 2 HP

Phase............................................................................................................................................ Single-Phase

Amps............................................................................................................................................................ 14A

Speed................................................................................................................................................ 1725 RPM

Power Transfer ............................................................................................................................... V-Belt Drive

Bearings..................................................................................................... Shielded & Permanently Lubricated

Main Specifications:

Operation Information

Swing Over Bed......................................................................................................................................... 16 in.

Distance Between Centers........................................................................................................................ 46 in.

Swing Over Tool Rest................................................................................................................................ 13 in.

Swing Over Tool Rest Base................................................................................................................ 13-1/2 in.

No of Spindle Speeds............................................................................................................................ Variable

Spindle Speed Range.............................................................................................................. 600 – 2400 RPM

Floor to Center Height............................................................................................................................... 43 in.

Headstock Rotation...................................................................................................... 0, 60, 90, 120, 180 deg.

-4-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

Spindle Information

Spindle Taper............................................................................................................................................ MT#2

Spindle Thread Size............................................................................................................................ 1" x 8 TPI

Spindle Thread Direction.................................................................................................................. Right Hand

Spindle Bore............................................................................................................................................. 3/8 in.

Type of Included Spindle Center................................................................................................................. Spur

Tool Rest Information

Tool Rest Width................................................................................................................................... 11-7/8 in.

Tool Rest Post Diameter......................................................................................................................... 25 mm

Tool Rest Post Length........................................................................................................................... 2-1/8 in.

Tool Rest Base Height......................................................................................................................... 1-7/16 in.

Tailstock Information

Tailstock Taper.......................................................................................................................................... MT#2

Type of Included Tailstock Center............................................................................................................... Live

Construction

Bed.......................................................................................................................... Precision-Ground Cast Iron

Frame................................................................................................................................................... Cast Iron

Stand.................................................................................................................................................... Cast Iron

Base..................................................................................................................................................... Cast Iron

Headstock............................................................................................................................................ Cast Iron

Tailstock............................................................................................................................................... Cast Iron

Paint Type/Finish.................................................................................................................................... Enamel

Other Specifications:

Country of Origin ................................................................................................................................................ China

Warranty ........................................................................................................................................................... 1 Year

Approximate Assembly & Setup Time .............................................................................................................. 1 Hour

Serial Number Location .................................................................................................................................. ID Label

ISO 9001 Factory .................................................................................................................................................. Yes

CSA, ETL, or UL Certified/Listed ............................................................................................................................ No

Features:

Spindle Tachometer with Digital Readout

Outboard Turning is Easy with Standard Tool Rest Extension

Quick Lock/Release Levers for Tailstock and Headstock

Heavy-Duty Cast Iron Bed and Legs Ensure Stability and Minimize Vibration

-5-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 1: SAFETY

For Your Own Safety, Read Instruction

Manual Before Operating This Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions.

This manual uses a series of symbols and signal words intended to convey the level of impor-

tance of the safety messages. The progression of symbols is described below. Remember that

safety messages by themselves do not eliminate danger and are not a substitute for proper

accident prevention measures. Always use common sense and good judgment.

Indicates an imminently hazardous situation which, if not avoided,

WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

MAY result in minor or moderate injury. It may also be used to alert

against unsafe practices.

This symbol is used to alert the user to useful information about

proper operation of the machine.

NOTICE

Safety Instructions for Machinery

OWNER’S MANUAL. Read and understand this ELECTRICAL EQUIPMENT INJURY RISKS. You

owner’s manual BEFORE using machine.

can be shocked, burned, or killed by touching live

electrical components or improperly grounded

machinery. To reduce this risk, only allow qualified

service personnel to do electrical installation or

repair work, and always disconnect power before

accessing or exposing electrical equipment.

TRAINED OPERATORS ONLY. Untrained oper-

ators have a higher risk of being hurt or killed.

Only allow trained/supervised people to use this

machine. When machine is not being used, dis-

connect power, remove switch keys, or lock-out

machine to prevent unauthorized use—especially

around children. Make workshop kid proof!

DISCONNECT POWER FIRST. Always discon-

nect machine from power supply BEFORE making

adjustments, changingtooling, orservicingmachine.

This prevents an injury risk from unintended startup

or contact with live electrical components.

DANGEROUS ENVIRONMENTS. Do not use

machinery in areas that are wet, cluttered, or have

poor lighting. Operating machinery in these areas

greatly increases the risk of accidents and injury.

EYE PROTECTION. Always wear ANSI-approved

safety glasses or a face shield when operating or

observing machinery to reduce the risk of eye

injury or blindness from flying particles. Everyday

eyeglasses are NOT approved safety glasses.

MENTAL ALERTNESS REQUIRED. Full mental

alertness is required for safe operation of machin-

ery. Never operate under the influence of drugs or

alcohol, when tired, or when distracted.

-6-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

WEARING PROPER APPAREL.- Do- not- wear- FORCING MAChINERY.-Do-not-force-machine.-

clothing,- apparel- or- jewelry- that- can- become-

entangled- in- moving- parts.- Always- tie- back- or-

cover-long-hair.-Wear-non-slip-footwear-to-avoid-

accidental-slips,-which-could-cause-loss-of-work-

piece-control.

It-will-do-the-job-safer-and-better-at-the-rate-for-

which-it-was-designed.

NEVER sTANd ON MAChINE.- Serious- injury-

may- occur- if- machine- is- tipped- or- if- the- cutting-

tool-is-unintentionally-contacted.-

hAzARdOus dusT. Dust- created- while- using-

machinery- may- cause- cancer,- birth- defects,- or-

long-term-respiratory-damage.-Be-aware-of-dust-

hazards-associated-with-each-workpiece-material,-

and-always-wear-a-NIOSH-approved-respirator-to-

reduce-your-risk.

sTABLE MAChINE. Unexpected-movement-dur-

ing- operation- greatly- increases- risk- of- injury- or-

loss-of-control.-Before-starting,-verify-machine-is-

stable-and-mobile-base-(if-used)-is-locked.

usE RECOMMENdEd ACCEssORIEs.-Consult-

this-owner’s-manual-or-the-manufacturer-for-rec-

ommended- accessories.- Using- improper- acces-

sories-will-increase-the-risk-of-serious-injury.

hEARING PROTECTION.- Always- wear- hear-

ing-protection-when-operating-or-observing-loud-

machinery.- Extended- exposure- to- this- noise-

without-hearing-protection-can-cause-permanent-

hearing-loss.

uNATTENdEd OPERATION. To- reduce- the-

risk- of- accidental- injury,- turn- machine- off- and-

ensure- all- moving- parts- completely- stop- before-

walking- away.- Never- leave- machine- running-

while-unattended.-

REMOVE AdJusTING TOOLs.- Tools- left- on-

machinery- can- become- dangerous- projectiles-

upon-startup.-Never-leave-chuck-keys,-wrenches,-

or- any- other- tools- on- machine.- Always- verify-

removal-before-starting!

MAINTAIN WITh CARE.-Follow-all-maintenance-

instructions- and- lubrication- schedules- to- keep-

machine- in- good- working- condition.- A- machine-

that- is- improperly- maintained- could- malfunction,-

INTENdEd usAGE.- Only- use- machine- for- its-

intended-purpose-and-never-make-modifications-

not- approved- by- Grizzly.- Modifying- machine- or- leading-to-serious-personal-injury-or-death.-

using- it- differently- than- intended- may- result- in-

ChECK dAMAGEd PARTs.- Regularly- inspect-

machine- for- any- condition- that- may- affect- safe-

operation.-Immediately-repair-or-replace-damaged-

or-mis-adjusted-parts-before-operating-machine.

malfunction-or-mechanical-failure-that-can-lead-to-

serious-personal-injury-or-death!

AWKWARd POsITIONs.- Keep- proper- footing-

and-balance-at-all-times-when-operating-machine.-

Do-not-overreach!-Avoid-awkward-hand-positions-

that-make-workpiece-control-difficult-or-increase-

the-risk-of-accidental-injury.

MAINTAIN POWER CORds. When-disconnect-

ing- cord-connected- machines- from- power,- grab-

and-pull-the-plug—NOT-the-cord.-Pulling-the-cord-

may- damage- the- wires- inside.- Do- not- handle-

cord/plug-with-wet-hands.-Avoid-cord-damage-by-

keeping-it-away-from-heated-surfaces,-high-traffic-

areas,-harsh-chemicals,-and-wet/damp-locations.

ChILdREN & BYsTANdERs. Keep-children-and-

bystanders-at-a-safe-distance-from-the-work-area.

Stop-using-machine-if-they-become-a-distraction.

GuARds & COVERs.-Guards-and-covers-reduce-

accidental- contact- with- moving- parts- or- flying-

debris.- Make- sure- they- are- properly- installed,-

undamaged,-and-working-correctly.

EXPERIENCING dIFFICuLTIEs. If- at- any- time-

you-experience-difficulties-performing-the-intend-

ed-operation,-stop-using-the-machine!-Contact-our-

Technical-Support-at-(570)-546-9663.

-7-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional Safety for Wood Lathes

MAIN INJURY HAZARDS: Death or crushing injury from getting entangled in rotating spindle

or workpiece; death, blindness, or broken bones from being struck by a workpiece that breaks

apart or comes loose during rotation, turning tool kickback, or flying wood chips. To minimize

your risk of these hazards, always heed the following warning information:

INTEGRITY OF STOCK. Verify each workpiece EYE/FACE PROTECTION. Always wear a face

is free of knots, splits, nails, or foreign material shield and safety glasses when operating lathe.

to ensure it can safely rotate on spindle without

breaking apart or causing turning tool kickback.

PROPER APPAREL. Do not wear gloves, necktie

or loose clothing. Keep keep long hair away from

WORKPIECE PREPARATION. Before mounting, rotating spindle.

cut off waste portions with a bandsaw or other tool

to ensure workpiece has no large edges to catch SPEED RATES. Select correct spindle speed for

turning tool, and it will rotate without dangerous workpiece size, type, shape, and condition. Use

wobbling.

low speeds when roughing or when turning large,

long, or non-concentric workpieces. Allow spindle

SECURING LOCKS. Verify tool rest, headstock, to reach full speed before turning.

and tailstock are secure before turning lathe ON.

NEW SETUPS. Test each new setup by starting

SECURING WORKPIECE. An improperly secured spindle rotation at the lowest speed and standing

workpiece can fly off spindle with deadly force. to the side of the lathe until workpiece reaches full

Use proven setup techniques and always verify speed and you can verify safe rotation.

workpiece is well-secured before starting lathe.

Only use high-quality fasteners with non-tapered ROUGHING. Use correct tool. Take light cuts,

heads for faceplate attachment.

use low speeds, and firmly support tool with both

hands.

TOOL SUPPORT. An improperly supported tool

may be grabbed or ejected. Adjust tool rest SHARP TOOLS. Only use sharp turning tools—

approximately ⁄4" away from workpiece and ⁄8

they cut with less resistance than dull tools. Dull

above workpiece center line to provide proper turning tools can catch or grab and pull your

support for turning tool. Firmly hold turning tool hands into the rotating workpiece.

with both hands against tool rest.

STOPPING SPINDLE. Always allow spindle to

TOOL KICKBACK. Occurs when turning tool is completely stop on its own. Never put hands or

ejected from workpiece with great force, striking another object on spinning workpiece.

operator or bystanders. Commonly caused by

poor workpiece selection/preparation, improper ADJUSTMENTS/MAINTENANCE. Make sure

tool usage, or improper machine setup or tool rest wood lathe is turned OFF, disconnected from

adjustment.

power, andallmovingparts are completely stopped

before doing adjustments or maintenance.

ADJUSTMENT TOOLS. Remove all chuck keys,

wrenches, and adjustment tools before turning MEASURING WORKPIECE. Only measure work-

lathe ON. A tool left on the lathe can become a piece after it has stopped. Trying to measure a

deadly projectile when spindle is started.

spinning workpiece increases entanglement risk.

SAFE CLEARANCES. Before starting spindle, SANDING/POLISHING. To reduce entanglement

verify workpiece has adequate clearance by hand- risk, remove tool rest before sanding. Never com-

rotating it through its entire range of motion.

pletely wrap sandpaper around workpiece.

-8-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 2: POWER SUPPLY

Availability

Before installing the machine, consider the avail-

ability and proximity of the required power supply

circuit. If an existing circuit does not meet the

requirements for this machine, a new circuit must

be installed. To minimize the risk of electrocution,

fire, or equipment damage, installation work and

electrical wiring must be done by an electrician or

qualified service personnel in accordance with all

applicable codes and standards.

Serious injury could occur if you connect

machine to power before completing setup

process. DO NOT connect to power until

instructed later in this manual.

110V Circuit Requirements

This machine is prewired to operate on a power

supply circuit that has a verified ground and meets

the following requirements:

Nominal Voltage .............................. 110V–120V

Cycle..........................................................60 Hz

Phase........................................... Single-Phase

Power Supply Circuit ......................... 20 Amps

Electrocution, fire, or

equipment damage may

occur if machine is not

correctly grounded and

connected to the power

supply.

A power supply circuit includes all electrical

equipment between the breaker box or fuse panel

in the building and the machine. The power sup-

ply circuit used for this machine must be sized to

safely handle the full-load current drawn from the

machine for an extended period of time. (If this

machine is connected to a circuit protected by

fuses, use a time delay fuse marked D.)

Full-Load Current Rating

The full-load current rating is the amperage a

machine draws at 100% of the rated output power.

On machines with multiple motors, this is the

amperage drawn by the largest motor or sum of all

motors and electrical devices that might operate

at one time during normal operations.

For your own safety and protection of

property, consult an electrician if you are

unsure about wiring practices or electrical

codes in your area.

Full-Load Current Rating at 110V...... 14 Amps

The full-load current is not the maximum amount

of amps that the machine will draw. If the machine

is overloaded, it will draw additional amps beyond

the full-load rating.

Note: Circuit requirements in this manual apply to

a dedicated circuit—where only one machine will

be running on the circuit at a time. If machine will

be connected to a shared circuit where multiple

machines may be running at the same time, con-

sult an electrician or qualified service personnel to

ensure circuit is properly sized for safe operation.

If the machine is overloaded for a sufficient length

of time, damage, overheating, or fire may result—

especially if connected to an undersized circuit.

To reduce the risk of these hazards, avoid over-

loading the machine during operation and make

sure it is connected to a power supply circuit that

meets the specified circuit requirements.

-9-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

Improper connection of the equipment-grounding

wire can result in a risk of electric shock. The

wire with green insulation (with or without yellow

stripes) is the equipment-grounding wire. If repair

or replacement of the power cord or plug is nec-

essary, do not connect the equipment-grounding

wire to a live (current carrying) terminal.

Grounding & Plug Requirements

This machine MUST be grounded. In the event

of certain malfunctions or breakdowns, grounding

reduces the risk of electric shock by providing a

path of least resistance for electric current.

This machine is equipped with a power cord that

has an equipment-grounding wire and a ground-

ing plug (similar to the figure below). The plug

must only be inserted into a matching receptacle

(outlet) that is properly installed and grounded in

accordance with all local codes and ordinances.

Check with a qualified electrician or service per-

sonnel if you do not understand these grounding

requirements, or if you are in doubt about whether

the tool is properly grounded. If you ever notice

that a cord or plug is damaged or worn, discon-

nect it from power, and immediately replace it with

a new one.

GROUNDED

5-15 RECEPTACLE

Extension Cords

Grounding Prong

We do not recommend using an extension cord

with this machine. If you must use an extension

cord, only use it if absolutely necessary and only

on a temporary basis.

5-15 PLUG

Extension cords cause voltage drop, which may

damage electrical components and shorten motor

life. Voltage drop increases as the extension cord

size gets longer and the gauge size gets smaller

(higher gauge numbers indicate smaller sizes).

Neutral Hot

Figure 2. Typical 5-15 plug and receptacle.

Any extension cord used with this machine must

contain a ground wire, match the required plug

and receptacle, and meet the following require-

ments:

Minimum Gauge Size...........................14 AWG

Maximum Length (Shorter is Better).......50 ft.

SHOCK HAZARD!

Two-prong outlets do not meet the grounding

requirements for this machine. Do not modify

or use an adapter on the plug provided—if

it will not fit the outlet, have a qualified

electrician install the proper outlet with a

verified ground.

-10-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 3: SETUP

Unpacking

Inventory

Your machine was carefully packaged for safe

transportation. Remove the packaging materials

from around your machine and inspect it. If you

discover any damage, please call us immediately

at (570) 546-9663 for advice.

The following is a list of items shipped with your

machine. Before beginning setup, lay these items

out and inventory them.

If any non-proprietary parts are missing (e.g. a

nut or a washer), we will gladly replace them; or

for the sake of expediency, replacements can be

obtained at your local hardware store.

Save the containers and all packing materials for

possible inspection by the carrier or its agent.

Otherwise, filing a freight claim can be difficult.

Box 1 Inventory (Figure 3)

Qty

When you are completely satisfied with the condi-

tion of your shipment, inventory the contents.

A. Lathe Unit................................................... 1

B. Faceplate 6" ............................................... 1

C. Hardware Bag ............................................ 1

D. Knockout Tool............................................. 1

E. Flat Wrenches 32mm ................................. 2

SUFFOCATION HAZARD!

Keep children and pets away

from plastic bags or packing

materials shipped with this

machine. Discard immediately.

Needed for Setup

The following are needed to complete the setup

process, but are not included with your machine.

Description

Qty

Figure 3. Box 1 inventory.

•

Additional People .........................At Least 2

Safety Glasses ............... 1 For Each Person

Cleaner/Degreaser (Page 13) .... As Needed

Disposable Shop Rags............... As Needed

Mounting Hardware (Page 15) ... As Needed

Precision Level ........................................... 1

Measuring Tape.......................................... 1

-11-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

Hardware Bag Inventory (Figure 4)

Qty

F. Spur Center................................................ 1

G. Live Center ................................................. 1

H. Tool Rest Lock Lever.................................. 1

I. Hex Wrenches 3mm, 4mm, 6mm......1 Each

J. Cap Screws M8-1.25 x 35.......................... 8

K. Lock Washers 8mm.................................... 8

L. Quill Lock Lever.......................................... 1

NOTICE

If you cannot find an item on this list, care-

fully check around/inside the machine and

packaging materials. Often, these items get

lost in packaging materials while unpack-

ing or they are pre-installed at the factory.

Box 2 Inventory (Figure 5)

Qty

M. Stand Legs ................................................. 2

Figure 4. Hardware bag inventory.

Figure 5. Box 2 inventory.

-12-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleanup

Gasoline and petroleum

products have low flash

points and can explode

or cause fire if used to

clean machinery. Avoid

using these products

to clean machinery.

The unpainted surfaces of your machine are

coated with a heavy-duty rust preventative that

prevents corrosion during shipment and storage.

This rust preventative works extremely well, but it

will take a little time to clean.

Be patient and do a thorough job cleaning your

machine. The time you spend doing this now will

give you a better appreciation for the proper care

of your machine's unpainted surfaces.

Many cleaning solvents

are toxic if inhaled. Only

work in a well-ventilated

area.

There are many ways to remove this rust preven-

tative, but the following steps work well in a wide

variety of situations. Always follow the manufac-

turer’s instructions with any cleaning product you

use and make sure you work in a well-ventilated

area to minimize exposure to toxic fumes.

NOTICE

Avoid chlorine-based solvents, such as

acetone or brake parts cleaner, that may

damage painted surfaces.

Before cleaning, gather the following:

•

Disposable rags

Cleaner/degreaser (WD•40 works well)

Safety glasses & disposable gloves

Plastic paint scraper (optional)

T23692—Orange Power Degreaser

A great product for removing the waxy shipping

grease from your machine during clean up.

Basic steps for removing rust preventative:

1. Put on safety glasses.

2. Coat the rust preventative with a liberal

amount of cleaner/degreaser, then let it soak

for 5–10 minutes.

3. Wipe off the surfaces. If your cleaner/degreas-

er is effective, the rust preventative will wipe

off easily. If you have a plastic paint scraper,

scrape off as much as you can first, then wipe

off the rest with the rag.

Figure 6. T23692 Orange Power Degreaser.

4. Repeat Steps 2–3 as necessary until clean,

then coat all unpainted surfaces with a quality

metal protectant to prevent rust.

-13-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

Site Considerations

Weight Load

Physical Environment

Refer to the Machine Data Sheet for the weight

of your machine. Make sure that the surface upon

which the machine is placed will bear the weight

of the machine, additional equipment that may be

installed on the machine, and the heaviest work-

piece that will be used. Additionally, consider the

weight of the operator and any dynamic loading

that may occur when operating the machine.

The physical environment where the machine is

operated is important for safe operation and lon-

gevity of machine components. For best results,

operate this machine in a dry environment that is

free from excessive moisture, hazardous chemi-

cals, airborne abrasives, or extreme conditions.

Extreme conditions for this type of machinery are

generally those where the ambient temperature

range exceeds 41°–104°F; the relative humidity

range exceeds 20–95% (non-condensing); or the

environment is subject to vibration, shocks, or

bumps.

Space Allocation

Consider the largest size of workpiece that will

be processed through this machine and provide

enough space around the machine for adequate

operator material handling or the installation of

auxiliary equipment. With permanent installations,

leave enough space around the machine to open

or remove doors/covers as required by the main-

tenance and service described in this manual.

See below for required space allocation.

Electrical Installation

Place this machine near an existing power source.

Make sure all power cords are protected from

traffic, material handling, moisture, chemicals,

or other hazards. Make sure to leave access to

a means of disconnecting the power source or

engaging a lockout/tagout device, if required.

Lighting

Children or untrained people

may be seriously injured by

this machine. Only install in an

access restricted location.

Lighting around the machine must be adequate

enough that operations can be performed safely.

Shadows, glare, or strobe effects that may distract

or impede the operator must be eliminated.

Wall

30"

77"

19"

Recommended 48"

For Outboard Turning

Illustration Not To Scale

Figure 7. Minimum working clearances.

-14-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

Anchoring to Floor

Assembly

Anchoring machinery to the floor prevents tipping

or shifting and reduces vibration that may occur

during operation, resulting in a machine that runs

slightly quieter and feels more solid.

To mount the lathe to the stand:

1. Stand the legs up approximately 41" apart

and get them reasonably aligned, as shown

in Figure 9.

If the machine will be installed in a commercial or

workplace setting, or if it is permanently connected

(hardwired) to the power supply, local codes may

require that it be anchored to the floor.

If not required by any local codes, fastening the

machine to the floor is an optional step. If you

choose not to do this with your machine, we

recommend placing it on machine mounts, as

these provide an easy method for leveling and

they have vibration-absorbing pads.

41"

Anchoring to Concrete Floors

Lag shield anchors with lag screws (see below)

are a popular way to anchor machinery to a

concrete floor, because the anchors sit flush

with the floor surface, making it easy to unbolt

and move the machine later, if needed. However,

anytime local codes apply, you MUST follow the

anchoring methodology specified by the code.

Figure 9. Stand legs approximately 41" apart to

prepare for mounting the lathe.

2. Use the help of additional people to care-

fully lift the lathe onto the legs and align the

mounting holes.

Note: The headstock end is the heaviest and

usually requires two people lifting at that end.

Lag Screw

3. Secure the lathe to the legs with the (8)

M8-1.25 x 35 cap screws and 8mm lock

washers, as shown in Figure 10.

Flat Washer

Machine Base

Lag Shield Anchor

Concrete

Drilled Hole

x 8

Figure 8. Popular method for anchoring

machinery to a concrete floor.

Figure 10. Securing lathe to the stand leg.

-15-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

Quill Keyway

4. Install the tool rest lock lever to secure the

tool rest, as shown in Figure 11.

Test Run

Loose hair and clothing

could get caught in machin-

ery and cause serious per-

sonal injury. Keep loose

clothing and long hair away

from moving machinery.

Once assembly is complete, test run your machine

to make sure it runs properly and is ready for

regular operation.

Figure 11. Installing handle into tool rest.

5. Install the lever into the tailstock so that the

end of it mates with the quill keyway (see

Figure 12).

The test run consists of verifying the following:

1) The motor powers up and runs correctly, and

2) the safety disabling mechanism on the switch

works correctly.

Note: Make sure the dog-point end of the

lock lever fits into the quill keyway so that

the quill can move in and out of the tailstock

without rotating.

If, during the test run, you cannot easily locate

the source of an unusual noise or vibration, stop

using the machine immediately, then review

Troubleshooting on Page 35.

If you still cannot remedy a problem, contact our

Tech Support at (570) 546-9663 for assistance.

Quill

Keyway

To test run the machine:

1. Make sure you have read the safety instruc-

tions at the beginning of the manual and that

the machine is set up properly.

Quill

Lock Lever

Figure 12. Quill lock lever.

2. Make sure all tools and objects used during

setup are cleared away from the machine.

6. Attach the digital readout to the top of the

head with the pre-installed Phillips head

screws, lock washers, and flat washers, as

shown in Figure 13.

3. Connect the machine to the power source.

4. Verify that the machine is operating correctly

by turning the machine ON.

—When operating correctly, the machine

runs smoothly with little or no vibration or

rubbing noises.

x 2

—Investigate and correct strange or unusual

noises or vibrations before operating the

machine further. Always disconnect the

machine from power when investigating or

correcting potential problems.

Figure 13. Digital readout installed.

-16-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Turn the machine OFF.

10. Test the variable speed by pulling the speed

lever out (Figure 15) and slowly adjusting it

left and right.

6. Remove the switch disabling key, as shown

in Figure 14.

Variable

Speed Lever

Figure 14. Example of removing switch key from

paddle switch.

Figure 15. Variable speed lever.

7. Try to start the machine with the paddle

—The machine should speed up and slow

down as you move the lever. If this is the

case, then the test run is over and your

machine is ready for normal operations.

switch.

—If the machine does not start, the switch

disabling feature is working as designed.

—If the lathe has problems changing speeds,

turn the lathe OFF, disconnect it from

power, and refer to the troubleshooting

chart on Page 35, or call our Tech Support

at (570) 546-9663 for additional help.

—If the machine starts, immediately stop the

machine. The switch disabling feature is

not working correctly. This safety feature

must work properly before proceeding with

regular operations. Call Tech Support for

help.

The spindle speed lever adjusts the pulley

width to change the spindle speed. To pre-

vent damage to this mechanism, the lathe

MUST be running before using the variable

speed lever.

8. Re-insert the switch disabling key.

9. Turn the lathe ON.

-17-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 4: OPERATIONS

To complete a typical operation, the operator

does the following:

Operation Overview

1. Examines the workpiece to make sure it is

suitable for turning. No extreme bows, knots,

or cracks should exist.

The purpose of this overview is to provide the nov-

ice machine operator with a basic understanding

of how the machine is used during operation, so

the machine controls/components discussed later

in this manual are easier to understand.

2. Prepares and trims the workpiece to make it

roughly concentric.

Due to the generic nature of this overview, it is

not intended to be an instructional guide. To learn

more about specific operations, read this entire

manual and seek additional training from expe-

rienced machine operators, and do additional

research outside of this manual by reading "how-

to" books, trade magazines, or websites.

3. Installs the workpiece between centers, or

attaches it to a faceplate or chuck.

4. Adjusts the tool rest to ¹⁄8" above the workpiece

centerline, and sets the minimum clearance

between the workpiece and the lip of the tool

rest to ¹⁄4".

5. Rotates the workpiece by hand to verify

that the spindle and workpiece rotate freely

throughout the full range of motion.

To reduce your risk of

serious injury, read this

entire manual BEFORE

using machine.

6. Ties back loose hair and clothing, and puts

on face shield and respirator. Takes all other

required safety precautions.

7. Starts the lathe, adjusts the lathe speed, and

carefully begins the turning operation, keep-

ing the chisel against the tool rest the entire

time it is cutting.

To reduce risk of eye injury from flying

chips or lung damage from breathing dust,

always wear safety glasses and a respirator

when operating this machine.

If you are not experienced with this type

of machine, WE STRONGLY RECOMMEND

that you seek additional training outside of

this manual. Read books/magazines or get

formal training before beginning any proj-

ects. Regardless of the content in this sec-

tion, Grizzly Industrial will not be held liable

for accidents caused by lack of training.

-18-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

Stock Inspection &

Requirements

Adjusting Head

The Model G0462 headstock can be positioned

anywhere along the bed and pivoted up to 180˚.

Some workpieces are not safe to turn or may

require modification before they are safe to

turn. Before turning a workpiece, inspect all

workpieces for the following:

To position the headstock along the length of

the bed:

1. DISCONNECT LATHE FROM POWER!

•

Workpiece Type:

This machine is intended for cutting natural

and man-made wood products, and some

plastics. Never attempt to cut any metal,

stone, or rubber workpiece; cutting these

materials can lead to machine damage or

severe injury.

2. Loosen the head lock lever shown in

Figure 16.

Head Lock

Lever

•

Foreign Objects:

Nails, staples, dirt, rocks and other foreign

objects are often embedded in wood. While

cutting, these objects can become dislodged

and hit the operator, cause tool grab, or break

the turning tool, which might then fly apart.

Always visually inspect your workpiece for

these items. If they can't be removed, DO

NOT turn the workpiece.

•

Large/Loose Knots:

Figure 16. Head lock lever.

Loose knots can become dislodged during

the turning operation. Large knots can cause

a workpiece to completely break in half dur-

ing turning and cause machine damage and

personal injury. Choose workpieces that do

not have large/loose knots.

3. Slide the headstock to the desired position,

then retighten the lock lever.

Note: The large hex nut under the headstock

may require occasional adjustment to ensure

proper clamping pressure to the bed. Turn

the hex nut in small increments to fine tune

the clamping pressure, as needed.

•

Wet or "Green" Stock:

Cutting wood with a moisture content over

20% causes unnecessary wear on tooling

blades, increases the risk of tool grab, and

yields poor results.

If the lathe head unexpectedly moves during

operation, the tool and your hand could be

drawn into the spinning workpiece resulting

in death or crushing injuries. ALWAYS make

sure the head lock lever is tight and the

head pivot pin is seated before operation.

•

Excessive Warping:

Workpieces with excessive bowing or twist-

ing are unstable and unbalanced. Never turn

these workpieces at high speed, or instability

will be magnified and the workpiece can be

ejected from the lathe causing impact injures.

Only turn concentric workpieces!

-19-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

To pivot the headstock:

Adjusting Tailstock

Position

1. DISCONNECT LATHE FROM POWER!

2. Make sure the head lock lever is tight.

The tailstock is equipped with a cam-action

clamping system to secure it. When the lock lever

is tightened, a locking plate lifts up and secures

the tool rest to the bed.

3. Pull the pivot lock pin out (see Figure 17) and

pivot the headstock clockwise 90˚ or 180˚, as

shown in Figure 18.

To reposition the tailstock along the bed, loosen

the tailstock lock lever (see Figure 19), move the

tailstock to the desired position, then retighten the

lock lever.

Pivot

Lock Pin

Note: If the lock lever does not securely clamp the

tailstock down onto the bed, loosen or tighten the

hex nut located on the underside of the tailstock in

small increments to achieve the proper clamping

pressure.

Head

Lock Lever

Figure 17. Pivot lock pin location.

Tailstock

Lock Lever

Figure 19. Tailstock lock lever.

Figure 18. Head set at 90˚ and 180˚.

4. Release the pivot lock pin. Make sure the pin

has engaged in its detent by trying to rotate

the headstock.

-20-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

For safe and good turning results, we recommend

Adjusting Tool Rest

positioning the tool rest approximately ⁄4" away

from the workpiece, and approximately ¹⁄8" above

the workpiece center line (see Figure 21).

The tool rest is equipped with a cam-action clamp-

ing system to secure it. When the base lock lever

is tightened, a clamping plate lifts up and secures

the tool rest to the bed.

¹⁄4"

Workpiece

Distances

¹⁄8"

Center Line

If tool rest unexpectedly moves during oper-

ation, the tool and your hand could be

drawn into the spinning workpiece result-

ing in death or crushing injuries. ALWAYS

make sure all tool rest locks are tight before

beginning operation.

Tool Rest

The Model G0462 comes with a three-way adjust-

able tool rest (see Figure 20).

Figure 21. Tool rest position relative to the

workpiece.

•

Use the base lock lever to secure the tool rest

along the length of the bed.

Use the pivot arm lock lever to secure the tool

rest at a working distance from the workpiece.

Use the tool rest lock lever to adjust the

height and angle of the tool rest relative to the

workpiece.

Base

Lock Lever

Tool Rest

Lock Lever

Pivot Arm

Lock Lever

Figure 20. Tool rest controls.

-21-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

removin spur

Removing Spur Center

1. DISCONNECT LATHE FROM POWER!

Installing/Removing

Spur Center

2. Hold a clean rag under the spindle or wear a

glove to catch the center when you remove it.

The included MT#2 spur center installs in the

spindle and forces the workpiece to spin with the

spindle.

3. Insert the knockout tool through the outboard

end of the spindle and firmly tap the center

until it breaks loose (see Figure 23).

Typically, the spur center is driven into the

workpiece (see Spindle Turning on Page 27 for

detailed instructions), then the center is inserted

with the workpiece into the spindle.

Installing Spur Center

1. DISCONNECT LATHE FROM POWER!

2. Move the tailstock and tool rest a safe work-

ing distance from the headstock.

Knockout Tool

3. If the faceplate is installed, remove it (refer to

Page 24 for detailed instructions).

4. Make sure the spur center and the inside of

the spindle are free of debris and oily sub-

stances that could interfere with proper mat-

ing of the parts.

Figure 23. Removing spur center using the

knockout tool.

5. Insert the tapered end of the center into the

spindle, then push it in with a quick, firm

motion (see Figure 22).

Before beginning any turning operation

that uses the live center installed into the

tailstock quill, make sure the spur and

live centers are properly aligned (refer to

Aligning Centers on Page 37 for detailed

instructions). Failure to heed this warning

could result in the workpiece being thrown

from the lathe, resulting in death or serious

personal injury.

Spur Center

Figure 22. Inserting spur center into spindle.

6. Make sure the center is securely installed by

attempting to pull it out by hand—a properly

installed center will not pull out by hand.

-22-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Rotate the quill handwheel to draw the quill

back into the tailstock as far as possible with-

out forcing the center to release.

Installing/Removing

Live Center

Note: The more the quill is drawn back into

the tailstock, the greater the workpiece sup-

port.

The MT#2 live center installs into the tailstock quill

and rotates with the workpiece.

7. Tighten the quill lock lever to hold the quill

Installing Live Center

and center in place.

1. Move the tailstock a safe working distance

from the head and tool rest.

2. Loosen the quill lock lever, then rotate the quill

handwheel clockwise until the quill extends

out from the tailstock about 1", as shown in

Figure 24.

The tailstock quill lock lever MUST be tight

and firmly secure the quill in place before

beginning operation. Also, the quill should

not protrude from the tailstock more than

2" or the quill will not adequately support

the workpiece. Otherwise, the workpiece

could come loose and fly at the operator

or bystanders resulting in death or serious

personal injury.

Quill

Removing Live Center

1. Loosen the quill lock lever.

Live Center

2. Hold a clean rag under the center or wear a

glove to catch the center when you remove it.

Quill

Lock Lever

3. Rotate the quill handwheel counterclockwise

to retract the quill back into the tailstock until

the center is forced out.

Figure 24. Installing the live center into the

tailstock.

3. Make sure the live center and the inside of

the quill are free of debris and oil substances

that could interfere with the proper mating of

these parts.

4. Insert the tapered end of the live center into

the quill with a quick, firm motion.

5. Make sure the center is secure by attempting

to pull it out by hand—a properly installed

center will not pull out by hand.

-23-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Use the two included 32mm flat wrenches to

tighten the faceplate, as shown in Figure 25.

Installing/Removing

Faceplate

The faceplate is used when you need to remove

material from the face of the workpiece, such as

during hollowing operations. The faceplate can be

installed only if the spur center is removed from

the spindle.

To install the faceplate:

1. DISCONNECT LATHE FROM POWER!

2. If the spur center is installed, remove it (refer

to Page 22 for detailed instructions).

Figure 25. Tightening the faceplate onto the

spindle.

3. Make sure the internal threads of the face-

plate and the threads of the spindle are free

of any debris, then wipe the threads with a

lightly oiled rag to aid in the installation and

removal.

To remove the faceplate, perform Steps 3–4 in

reverse.

For detailed instructions on mounting a workpiece

to the faceplate, refer to Faceplate Turning on

Page 29.

4. Thread the faceplate onto the spindle clock-

wise.

-24-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting Spindle

Speed

Always choose the correct spindle speed

for your operation. Using the wrong speed

may lead to the workpiece breaking loose

or being thrown from the lathe at a high rate

of speed, causing fatal or severe impact

injuries.

Spindle speed must be adjusted while lathe

is running. Adjusting spindle speed while

machine is not in operation could result in

permanent damage to the machine not cov-

ered under warranty.

Refer to the chart in Figure 27 to help choose the

correct spindle speed. Note that both the diameter

of the workpiece and the type of cutting should be

considered when determining the proper spindle

speed.

The Model G0462 is engineered to operate

between 600 and 2400 RPM's. Due to the design

of the pulley system, RPM's outside of this range

cannot be attained.

Diameter Roughing General Finishing

of Work-

piece

RPM

Cutting

RPM

Use the digital readout as a guide. Select a speed

within the set range by pulling out the speed

control lever and turning it to the right to increase

RPM or to the left to decrease the RPM (see

Figure 26).

Fastest

available

Under 2"

2–4"

1520

760

2400

1600

1080

810

Fastest

available

Slowest

available

4–6"

1650

1240

1000

830

Slowest

available

6–8"

Slowest

available

Slowest

available

8–10"

10–12"

12–14"

Slowest

available

Slowest

available

Slowest

available

Slowest

available

710

Variable

Speed Lever

Figure 27. Typical spindle speed

recommendations.

Figure 26. Speed lever.

When turning a workpiece where a lot of mate-

rial must be removed and a rough finish does not

matter, low range, which has more torque, is best.

When turning a workpiece where a clean finish is

required, and only light cuts are made, high range

is best. Mid range is a compromise between the

two ranges. Use the speed lever to adjust the

spindle speed within each range.

-25-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

•

Scrapers—Mainly used where access for

other tools is limited, such as hollowing oper-

ations. This is a flat, double-ground tool that

comes in a variety of profiles (Round Nose,

Spear Point, Square Nose, etc.) to match

many different contours. Figure 30 shows an

example of a round nose scraper.

Selecting Turning

Tools

Lathe tools come in a variety of shapes and sizes

and usually fall into five major categories.

Refer to Accessories on Page 31 for examples of

recommended wood chisels from Grizzly.

•

Gouges—Mainly used for rough cutting,

detail cutting, and cove profiles. The rough

gouge is a hollow, double-ground tool with

a round nose, and the detail gouge is a hol-

low, double-ground tool with either a round or

pointed nose. Figure 28 shows an example

of a gouge.

Figure 30. Round nose scraper.

•

Parting Tools—Used for sizing and cut-

ting off work. This is a flat tool with a sharp

pointed nose that may be single- or double-

ground. Figure 31 shows an example of a

parting tool.

Figure 28. Gouge.

•

Skew Chisel—A very versatile tool that can

be used for planing, squaring, V-cutting,

beading, and parting off. The skew chisel

is flat, double-ground with one side higher

than the other (usually at an angle of 20-40˚).

Figure 29 shows an example of a skew

chisel.

Figure 31. Parting tool.

•

Specialty Tools—These are the unique,

special function tools to aid in hollowing, bowl

making, cutting profiles, etc.

Figure 29. Skew chisel.

-26-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

To set up a spindle turning operation:

Spindle Turning

1. Mark both ends of your workpiece by draw-

ing diagonal lines from corner to corner. The

intersection point of these lines will show you

the center of your workpiece. See the illustra-

tion in Figure 33 for details.

Spindle turning, as shown in Figure 32, is the

operation performed when a workpiece is mount-

ed between the spindle and quill centers.

Workpiece

Pencil Lines

Marked Diagonally

Across Corners

Workpiece

Center

Typical spindle turning operation.

Figure 32.

Figure 33. Workpiece marked diagonally from

corner to corner to determine the center.

2. Use a wood mallet to tap the point of the spur

center into the workpiece where the lines

intersect so that it leaves a center mark, then

remove the center. Do this to both ends of the

workpiece.

Before beginning any turning operation

that uses the live center installed into the

tailstock quill, make sure the spur and

live centers are properly aligned (refer to

Aligning Centers on Page 37 for detailed

instructions). Failure to heed this warning

could result in the workpiece being thrown

from the lathe resulting in death, blindness,

or broken bones.

3. Use a ⁄4" drill bit to make a ⁄4" deep hole at

the center mark on the workpiece end that

will be mounted on the spindle spur center.

4. To help embed the spur center into the

workpiece, cut ⁄8" deep saw kerfs into the

same workpiece end along the diagonal lines

marked in Step 1.

5. If your workpiece is over 2" x 2", cut the cor-

ners off the workpiece length-wise to make

turning the corners safer and easier.

-27-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Use a wood mallet to embed the spur center

11. Position the tool rest approximately ⁄4" away

at least ⁄4" into the workpiece end center

from the workpiece and approximately ⁄8

mark, as illustrated in Figure 34.

above the center line, as illustrated in Figure

35.

Workpiece

⁄4

Distances

¼"

⁄8

Center Line

Tool Rest

Figure 34. Spur center properly embedded.

Figure 35. Tool rest set ¹⁄8" above the

center line and ¹⁄4" away from workpiece.

7. With the workpiece still attached, insert the

spur center into the spindle.

12. Test the setup by hand-turning the workpiece

to make sure there is enough clearance all

the way around before turning the lathe ON.

8. With the live center installed in the quill, draw

the quill back into the spindle as far as pos-

sible without forcing the center to release.

Spindle Turning Tips

Note: This will give the quill and center the

greatest amount of support to safely hold the

workpiece during operation.

•

When turning the lathe ON, stand outside the

path of the rotating workpiece until the lathe

reaches full speed and you can verify that the

lathe will not throw the workpiece.

9. Loosen the tailstock lock lever, slide the

tailstock toward the workpiece until the live

center touches the workpiece centerpoint,

then lock the tailstock in this position.

•

Use the slowest speed when starting or stop-

ping the lathe, and when rough cutting.

Select the correct speed for the size of

the workpiece you are turning. Use slower

speeds for large workpieces (4" diameter and

over); use the middle range speeds for medi-

um sized workpieces (2"–4" diameter); and

use faster speeds for small sized workpieces

(under 2" in diameter).

10. Use the quill handwheel to push the live

center into the workpiece at least a ⁄4", then

tighten the quill lock lever to secure the cen-

ter and quill.

Do not press the live center into the

workpiece too firmly or the center bearings

will bind and overheat. Likewise, do not

press the center too lightly or the workpiece

could come loose and spin off the lathe. Use

good judgement. Serious personal injury

could result if care is not taken in this pro-

cedure.

•

Keep the turning tool on the tool rest the

ENTIRE time that it is approaching the

workpiece and is in contact with it.

Learn the correct techniques for each tool

you will use. If you are unsure, read books or

magazines about lathe techniques and seek

training from experienced users.

-28-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Use the mark made in Step 1 to center the

faceplate onto the workpiece back, then

attach it with wood screws that do not have

tapered heads as shown in Figure 38.

Faceplate Turning

Faceplate turning, as shown in Figure 36, is when

a workpiece is mounted to the faceplate that is

then mounted to the spindle. This type of turning

is usually done with open-faced workpieces like

bowls or plates.

Figure 38. Attaching the faceplate to a backing

block, which is glued to the workpiece.

3. Thread the faceplate onto the spindle and

tighten securely.

Figure 36. Typical faceplate turning operation.

Using a Backing Block

If wood screws cannot be used to attach the face-

plate to the workpiece, then use a backing block

that is securely glued to the workpiece.

Attaching Faceplate to Spindle

1. Use the procedure in Spindle Turning on

Page 27 to mark the center of the workpiece.

To mount your workpiece to a backing block:

Note: Cut off the excess corners of the

workpiece to make it as close to "round" as

possible.

1. Make the backing block from a piece of scrap

wood that is flat on both sides and free of

knots or splits.

2. Locate and mark the center of both the

DO NOT use screws with tapered heads

to attach the faceplate because they could

split the faceplate, or the screws could snap

off during operation. See the illustration in

Figure 37 for examples.

workpiece and the backing block.

3. Drill a ¹⁄4" hole completely through the center

of the backing block.

4. Looking through the hole in the backing block

to line it up with the center of the workpiece,

glue and clamp the backing block to the

workpiece.

Correct

Incorrect

Note: Allow the glue joint to completely cure

according to the glue manufacturer's instruc-

tions.

5. Follow steps 1-2 in Attaching Faceplate to

Spindle to attach the faceplate to the backing

block.

Figure 37. Correct screw type for faceplate

attachment.

-29-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

Outboard Turning

Sanding/Finishing

Using the Lathe

Outboard turning is a variation of faceplate turn-

ing and is usually done when stock diameter is

greater than 12''. For the size of the Model G0462

and its minimum turning speed, we recommend a

maximum diameter of 17'' for outboard turning.

The lathe can be used for finishing procedures

after the turning operations are complete and

before removing the workpiece from the lathe,

such as sanding, polishing, and applying finishes

by hand (see Figure 41 for an example).

The lathe setup at 90˚ for outboard turning uses

the tool rest with the pivot arm extended, as

shown in Figure 39.

Note: When using the lathe to sand or finish the

workpiece, remove the tool rest to prevent entan-

glement hazards. Use the slowest speed for safer

control and better results.

Figure 39. Headstock set at 90˚.

Figure 40 depicts the lathe setup at 180˚ for out-

board turning.

Figure 41. Typical sanding operation.

Note: When turning in this manner, you must use

a free standing tool rest (not supplied).

Sandpaper

Wrapping the sandpa-

per completely around

the workpiece could pull

your hands into the mov-

ing workpiece and may

cause injury. Never wrap

sandpaper completely

around the workpiece!

Workpiece

Figure 40. Headstock set at 180˚.

-30-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

ACCESSORIES

SECTION 5: ACCESSORIES

T25535—The New Turning Wood

The appeal of woodturning is simple: with only

a few hand tools and a lathe, remarkable results

can be quickly achieved, including beautiful bowls,

boxes in the round, lamp bases, and furniture

parts. For over 20 years, woodturners have been

turning to Richard Raffan for expert advice and

inspiration.

Installing unapproved accessories may

cause machine to malfunction, resulting in

serious personal injury or machine damage.

To reduce this risk, only install accessories

recommended for this machine by Grizzly.

NOTICE

Refer to our website or latest catalog for

additional recommended accessories.

H8034—3" 3-Jaw Wood Chuck - 1" x 8 TPI

H7605—3" 4-Jaw Wood Chuck - 1" x 8 TPI

These self-centering style 3- and 4-Jaw Chucks

have reversible stepped jaws for holding a variety

of workpiece sizes. Setup is quick and easy by

twisting the knurled adjustment plate on the back

of the chuck. Two 4" wrenches are included for

final tightening. Fits all wood lathes with 1" x 8 TPI

spindles.

Figure 43. Instructional Text.

T10501—9 Piece Wood Lathe Center Kit

This all-in-one set features a variety of

interchangeable lathe centers for every spindle

turning application. Includes: MT #1 and MT #2

live centers, 3 spur centers, 3 multi-spur centers,

mounting adapter, wrenches and fitted case. Fits

lathes with 1" x 8 TPI RH spindles.

Figure 42. 3" 4-jaw chuck.

Figure 44. Lathe center kit with fitted case.

order online at www.grizzly.com or call 1-800-523-4777

-31-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

H7924—6 pc. Chisel Set In Aluminum Box

This Lathe Chisel Sets high speed steel blades

and graceful ash handles provide plenty of control.

Handles measure 10" long and chisels measure

15¹⁄2" long overall. Set includes a ³⁄16" parting tool,

H5954—Robert Sorby Stebcentre MT#2

Razor sharp teeth bite into the workpiece for

secure operation and the spring loaded center

point controls the amount of drive or slip. This pat-

ented feature helps avoid the problem of ‘dig-in’.

Production turners can also load and unload their

work while the lathe is still running!

⁄

2" round nose, ⁄8" skew, ⁄8" gouge, ⁄2" gouge,

and 1" gouge. All chisels are protected in a tough

aluminum case.

Figure 47. MT#2 Stebcentre.

Figure 45. 6 pc. chisel set with aluminum case.

T10117—Big Mouth Dust Hood with Stand

Capture dust from any machine operation with

this Big Mouth Dust Hood. Simply attach a 4" dust

collection hose and adjust the hood right where

you need it. The free standing base eliminates

H0507—20" Hollowing Tool

H0508—24" Hollowing Tool

An excellent choice for blind turning or undercut-

ting where reach is restricted. H0507 is designed

for end grain use while H0508 (with a more sub-

stantial steel cross section) is designed for both

end grain and side grain (bowl) use.

complicated machine set-ups and the tilting 16³⁄8

x 12⁷⁄8" hood adjusts from 23" to 43" high. Every

shop needs one of these!

Figure 46. Hallowing Tools.

Figure 48. Dust collector with hood.

-32-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 6: MAINTENANCE

Tailstock

Always disconnect power

to the machine before

performing maintenance.

Failure to do this may

result in serious person-

To remove the quill from the tailstock, loosen

the set screw above the quill handwheel, then

completely unthread the handwheel clockwise

from the quill threads. Loosen the quill lock lever

al injury.

and remove the quill from the tailstock housing.

Thoroughly clean all of the unpainted parts with

mineral spirits. After these surfaces are dry, apply

a thin coat of light machine oil.

Schedule

To re-assemble the quill and handwheel, insert the

For optimum performance from your machine,

follow this maintenance schedule and refer to any

specific instructions given in this section.

quill into the casting, then thread the handwheel

counterclockwise onto the quill until it moves

against the casting. Tighten down the set screw

that secures the handwheel, then back the set

screw off one full turn so that the handwheel can

freely rotate.

Daily Check:

•

Loose mounting bolts.

Worn switch.

Worn or damaged wires.

Damaged V-belt.

Any other unsafe condition.

Lubrication

Since all the bearings for the Model G0462 are

sealed and permanently lubricated, simply leave

them alone unless they need to be replaced. Do

not lubricate them.

Cleaning

Cleaning the Model G0462 is relatively easy.

Vacuum excess wood chips and sawdust, and

wipe off the remaining dust with a dry cloth. If any

resin has built up, use a resin dissolving cleaner

to remove it.

Wipe a lightly oiled shop rag on the outside spin-

dle threads. DO NOT allow any oil to get on the

inside mating surface of the spindle.

Use the quill handwheel to extend the quill all the

way out, then wipe the outside of the quill with a

lightly oiled shop rag. DO NOT allow any oil to get

on the inside quill mating surfaces.

Remove any debris or oily substances from inside

the spindle and quill.

Lathe Bed

Protect the unpainted cast iron lathe bed by wip-

ing it clean after every use—this ensures mois-

ture from wood dust does not remain on the bare

metal surfaces. Keep your lathe bed rust-free with

regular applications of quality lubricants.

-33-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Push tip of oil can nozzle against ball oiler,

then pump can once or twice. Alternatively,

if using a spray-type lubricant, place the end

of the straw against the ball oiler and give it a

quick squirt. Do not over-oil.

Motor Shaft Lubrication

The motor shaft must be properly lubricated

to ensure the variable-speed pulley assembly

can open and close smoothly when adjusted.

Any common machine oil is acceptable for this

purpose, but we recommend using a "dry" type

lubricant, such as Grizzly model G2545 or G4682,

to avoid attracting dust and prevent a build-up of

grime.

4. Turn lathe ON and run for approximately one

minute. Rotate variable-speed lever back and

forth to distribute oil.

5. Turn lathe OFF and re-install plastic cover.

To lubricate motor shaft:

1. DISCONNECT LATHE FROM POWER!

2. Remove plastic cover shown in Figure 49 to

access motor shaft ball oiler.

Plastic

Cover

Ball Oiler

Figure 49. Location to access ball oiler.

-34-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 7: SERVICE

Review the troubleshooting and procedures in this section if a problem develops with your machine. If you

need replacement parts or additional help with a procedure, call our Technical Support at (570) 546-9663.

Note: Please gather the serial number and manufacture date of your machine before calling.

Troubleshooting

Motor & Electrical

Symptom

Possible Cause

Possible Solution

Motor will not start,

or it growls on start

up.

1. Switch safety key is removed.

2. Power supply fuse or circuit breaker has

tripped.

1. Replace switch safety key.

2. Disconnect power, and inspect circuit for electrical

shorts and repair. Replace circuit breaker if it is old

or has tripped many times.

3. Motor fan cover is dented, stopping the fan 3. Replace or adjust fan cover. Inspect motor fan and

from being able to spin.

replace if damaged.

4. Paddle switch is broken or at fault.

4. Disconnect power, and use an ohmmeter to check

switch terminals for continuity, and replace switch if

required.

5. Start capacitor is at fault.

6. Motor is at fault.

5. Replace start capacitor.

6. Replace motor.

Fuses or circuit

1. Short circuit in line cord or plug.

breakers trip open.

2. Short circuit in motor or loose connections. 2. Short circuit in motor or loose connections.

3. Incorrect fuses or circuit breakers in power 3. Incorrect fuses or circuit breakers in power supply.

supply.

Vibration noise

while machine

is running; noise

changes when

speed is changed.

1. V-Belt cover loose.

1. Tighten the four screws that mount the V-belt cover;

if necessary, install a soft, vibration dampening

material between the V-belt cover and the

headstock casting.

2. V-Belt cover bent or dented and is making

contact with the motor pulley or V-belt.

2. Remove V-belt cover and inspect the inside for

dents, bends, or indications of rubbing. Tap out the

dent with a rubber mallet, bend back into proper

shape, or shim V-belt cover away from the motor

pulley.

3. Bad spindle bearing(s).

3. Replace spindle bearing(s).

Vibration noise

while machine

is running; noise

remains constant

when speed is

changed.

1. Dented fan cover on motor.

1. Replace or adjust fan cover. Inspect motor fan and

replace if damaged.

2. Bad spindle bearing(s).

2. Replace spindle bearing(s).

-35-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning

Symptom

Possible Cause

Possible Solution

Bad surface ﬁnish.

1. Wrong spindle speed.

2. Dull chisel or wrong chisel being used for

the operation.

1. Use trial-and-error to ﬁnd a better spindle speed.

2. Sharpen chisel or try a different chisel.

Inaccurate turning

results from one end

of the workpiece to

the other.

1. Headstock and tailstock are not properly

aligned with each other.

1. Realign the tailstock to the headstock (Page 37).

Can't remove

tapered tool from

quill.

1. Quill has not retracted all the way back into 1. Turn the quill handwheel until it forces taper out of

the tailstock.

quill.

2. Debris was not removed from taper before

inserting into quill.

2. Always make sure that taper surfaces are clean.

Quill will not

1. Keyway not aligned with the quill lock lever. 1. Align the quill keyway with the quill lock lever as

shown in Figure 12, on Page 16 and slightly tighten

move forward into

workpiece when

handwheel is

turned.

the lever to engage the keyway.

-36-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

Aligning Centers

Replacing V-Belt

To ensure accurate and safe results, make sure

that the spindle and quill centers are aligned

before beginning operations.

The pulley system that allows the Model G0462 to

operate at variable speeds also keeps the V-belt

properly tensioned. However, if the V-belt shows

signs of cracking, splitting, or any other damage,

we recommend you replace it to ensure optimum

power transmission.

To align the centers:

1. DISCONNECT LATHE FROM POWER!

2. Remove the tool rest from the bed.

To replace the V-belt:

1. DISCONNECT LATHE FROM POWER!

3. Install the centers, then slide the tailstock up

to the head so that the centers are facing

each other, as illustrated in Figure 50.

2. Remove the V-belt safety cover from the

back of the lathe.

3. Pull the motor pulley plates apart so that

the V-belt slips down to the motor arbor, as

shown in Figure 51. This will decrease the

V-belt tension.

Figure 50. Center tips touching to ensure

alignment.

4. Loosen the head lock lever, adjust the head

position so that center tips touch, then re-

tighten the lock lever to hold the head in

place.

Motor

Pulley

Plates

Note: If the spur center is lower than the

live center, use shims under the head. If the

live center is lower, use shims under the

tailstock.

Figure 51. Replacing the V-belt.

4. While keeping the tension off the V-belt, roll it

off the spindle pulley and remove it.

5. Install the new V-belt by reversing Steps

3–4.

6. Re-install the V-belt safety cover before con-

necting the lathe to power.

-37-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

machine

SECTION 8: WIRING

These pages are current at the time of printing. However, in the spirit of improvement, we may make chang-

es to the electrical systems of future machines. Compare the manufacture date of your machine to the one

stated in this manual, and study this section carefully.

If there are differences between your machine and what is shown in this section, call Technical Support at

(570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine. An updated

wiring diagram may be available. Note: Please gather the serial number and manufacture date of your

machine before calling. This information can be found on the main machine label.

Wiring Safety Instructions

SHOCK HAZARD. Working on wiring that is con- WIRE/COMPONENT DAMAGE. Damaged wires

nected to a power source is extremely dangerous. or components increase the risk of serious per-

Touching electrified parts will result in personal sonal injury, fire, or machine damage. If you notice

injury including but not limited to severe burns, that any wires or components are damaged while

electrocution, or death. Disconnect the power performing a wiring task, replace those wires or

from the machine before servicing electrical com- components.

ponents!

MOTOR WIRING. The motor wiring shown in

MODIFICATIONS. Modifying the wiring beyond these diagrams is current at the time of printing

what is shown in the diagram may lead to unpre- but may not match your machine. If you find this

dictable results, including serious injury or fire. to be the case, use the wiring diagram inside the

This includes the installation of unapproved after- motor junction box.

market parts.

CAPACITORS/INVERTERS. Some capacitors

WIRE CONNECTIONS. All connections must and power inverters store an electrical charge for

be tight to prevent wires from loosening during up to 10 minutes after being disconnected from

machine operation. Double-check all wires dis- the power source. To reduce the risk of being

connected or connected during any wiring task to shocked, wait at least this long before working on

ensure tight connections.

capacitors.

CIRCUIT REQUIREMENTS. You MUST follow EXPERIENCING DIFFICULTIES. If you are expe-

the requirements at the beginning of this man- riencing difficulties understanding the information

ual when connecting your machine to a power included in this section, contact our Technical

source.

Support at (570) 546-9663.

The photos and diagrams

included in this section are

best viewed in color. You

can view these pages in

color at www.grizzly.com.

-38-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

Electrical Components & Wiring Diagram

Hot

110 VAC

NEMA 5-15 Plug

(As Recommended)

Ground

Neutral

Figure 52. Paddle switch wiring.

Paddle

Switch

Figure 53. Motor wiring.

Digital Readout

Motor

Start Capacitor

100MFD 250VAC

Spindle Speed Sensor

READ ELECTRICAL SAFETY

ON PAGE 38!

-39-

G0462 Wood Lathe (Mfg. Since 3/10)

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 9: PARTS

Main

Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here

are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.

-40-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

Parts List

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

P0462001

P0462002

P0462003

P0462004

P0462005V2

PHLP HD SCR M5-.8 X 8

MOTOR COVER

P0462040

P0462041

P0462042

P0462043

P0462044

P0462045

P0462046

P0462047

P0462048

P0462049

P0462050

P0462051

P0462052

P0462053

P0462054

P0462057

P0462058

P0462059

P0462060

P0462061

P0462062

P0462063

P0462064

P0462065

P0462066

P0462067

P0462068

P0462069

P0462070

P0462071

EXT RETAINING RING 24MM

SPEED CHANGE LABEL

GEAR ASSEMBLY

HEX BOLT M8-1.25 X 30

LOCK WASHER 8MM

PHLP HD SCR M5-.8 X 12

PHLP HD SCR M4-.7 X 12

HEAD PIVOT LOCKING PIN

HEADSTOCK PIVOT BOLT

HEAD PIVOT BASE

5V2

MOTOR 2HP 110V 1-PH V2.01.09

5V2-1 P0462005V2-1 FAN COVER 156 X 68MM V2.01.09

5V2-2 P0462005V2-2 FAN 150 X 30MM V2.01.09

5V2-3 P0462005V2-3 S CPCTR 100M 250V V2.01.09

5V2-4 P0462005V2-4 MOTOR JUNCTION BOX V2.01.09

BED CLAMP A

P0462006

P0462007

P0462008

P0462009

P0462010

P0462011

P0462012

P0462013

P0462014

P0462015

P0462015-1

P0462015-2

P0462015-3

P0462015-4

P0462016

P0462016A

P0462017

P0462018

P0462019

P0462020

P0462021

P0462022

P0462023

P0462024

P0462025

P0462026

P0462027

P0462028

P0462029

P0462029-1

P0462030

P0462031

P0462032

P0462033

P0462034

P0462035

P0462036

P0462037

P0462038

P0462039

PUSH-OUT ROD

HEX NUT M18-2.5

EXT RETAINING RING 24MM

HOLLOW KNURL SET SCR M6 X 10

MOTOR PULLEY SET

EXT RETAINING RING 24MM

HEADSTOCK ECCENTRIC SHAFT

HEAD LOCK LEVER

15-1

15-2

15-3

15-4

16A

29-1

INT RETAINING RING 62MM

BALL BEARING 6007 ZZ

SHIFTING LEVER BRACKET

EXT RETAINING RING 35MM

RACK

SET SCREW M8-1.25 X 25

HEX NUT M8-1.25

BED

CAP SCREW M8-1.25 X 40

EXT RETAINING RING 19MM

BALL LEVER

SWITCH ASSEMBLY

SWITCH BOX

TOOL REST ECCENTRIC SHAFT

TOOL REST BODY

GRIZZLY PADDLE SWITCH W/KEY

PADDLE SWITCH KEY

SWITCH BOX PLATE

HEX NUT M18-2.5

TOOL REST CLAMP PLATE

TOOL REST PIVOT BOLT

HANDLE ASSY M10-1.5 X 15

EXT RETAINING RING 19MM

HANDLE ASSY M10-1.5 X 15

TOOL REST PIVOT ARM

TOOL REST 12-1/8L X 6-1/2H

TAILSTOCK LIVE CENTER MT#2

TAILSTOCK LOCK LEVER V2.11.09

TAILSTOCK CASTING V2.11.09

HEADSTOCK CASTING

HEADSTOCK ASSEMBLY

KEY 4 X 4 X 80

EXT RETAINING RING 16MM

MOTOR SHAFT SLEEVE

COMPRESSION SPRING

SPINDLE PULLEY SET

V-BELT M24.5 3L245

72V2 P0462072V2

73V2 P0462073V2

EXT RETAINING RING 16MM

STRAIN RELIEF M20-1.5

POWER CORD 16G 3W 5-15 PLUG

PHLP HD SCR M6-1 X 10

DIGITAL READOUT BRACKET

DIGITAL READOUT ASSEMBLY

RPM SENSOR

73V2A P0462073V2A TAILSTOCK ASSEMBLY V2.04.10

74V2 P0462074V2

75V2 P0462075V2

76V2 P0462076V2

77V2 P0462077V2

78V2 P0462078V2

80V2 P0462080V2

81V2 P0462081V2

82V2 P0462082V2

TAILSTOCK QUILL V2.04.10

QUILL LOCK HANDLE ASSY V2.04.10

HANDWHEEL SET SCREW V2.04.10

TLSTCK HNDWHL PLASTIC V2.04.10

HANDWHEEL HANDLE V2.04.10

TAILSTOCK PIVOT BOLT V2.04.10

TAILSTOCK CLAMP PLATE V2.04.10

HEX NUT M16-2

FLAT WRENCH 32MM

SPUR CENTER MT#2

FACEPLATE 6

P0462083

P0462084

P0462085

P0462086

P0462088

PHLP HD SCR M5-.8 X 12

BED END PLATE

SPINDLE 1 X 8

KEY 4 X 4 X 80

LOCK WASHER 8MM

BALL BEARING 6205ZZ

INT RETAINING RING 52MM

BALL BEARING 6205ZZ

EXT RETAINING RING 25MM

HEX NUT M8-1.25

STAND LEG LEFT/RIGHT

TAILSTOCK LEADSCREW V2.11.09

SET SCREW M6-1 X 12

96V2 P0462096V2

P0462097

P0462098

SPRING

-41-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

Machine Labels

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

P0462089

P0462090

P0462091

P0462092

MACHINE ID LABEL

P0462093

ELECTRICITY 1.4W X 1.2H

GRIZZLY LOGO LABEL

RPM DISPLAY/FACE SHIELD LABEL

READ MANUAL 2W X 3.3H V2.07.05

SPEED CHANGE LABEL

P0462094

P0462095

N/S GRIZZLY GREEN G1023S

Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes

off or becomes unreadable, the owner of this machine MUST replace it in the original location

before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.

-42-

G0462 Wood Lathe (Mfd. Since 11/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTY CARD

Name_____________________________________________________________________________

Street_____________________________________________________________________________

City _______________________ State_________________________ Zip _____________________

Phone #____________________ Email _________________________________________________

Model # ____________________ Order #_______________________ Serial #__________________

The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop

better products and services. Of course, all information is strictly confidential.

1. How did you learn about us?

____ Advertisement

____ Card Deck

____ Friend

____ Website

____ Catalog

____ Other:

2. Which of the following magazines do you subscribe to?

____ Cabinetmaker & FDM

____ Family Handyman

____ Hand Loader

____ Popular Science

____ Popular Woodworking

____ Precision Shooter

____ Projects in Metal

____ RC Modeler

____ Riﬂe

____ Shop Notes

____ Wooden Boat

____ Woodshop News

____ Woodsmith

____ Handy

____ Woodwork

____ Home Shop Machinist

____ Journal of Light Cont.

____ Live Steam

____ Woodworker West

____ Woodworker’s Journal

____ Other:

____ Model Airplane News

____ Old House Journal

____ Popular Mechanics

____ Shotgun News

____ Today’s Homeowner

____ Wood

3. What is your annual household income?

____ $20,000-$29,000

____ $30,000-$39,000

____ $40,000-$49,000

____ $70,000+

____ $50,000-$59,000

____ $60,000-$69,000

4. What is your age group?

____ 20-29

____ 30-39

____ 60-69

____ 40-49

____ 70+

____ 50-59

5. How long have you been a woodworker/metalworker?

____ 0-2 Years ____ 2-8 Years

____ 8-20 Years

____20+ Years

____10+

6. How many of your machines or tools are Grizzly?

____ 0-2 ____ 3-5

____ 6-9

7. Do you think your machine represents a good value?

8. Would you recommend Grizzly Industrial to a friend?

_____Yes

_____No

9. Would you allow us to use your name as a reference for Grizzly customers in your area?

Note: We never use names more than 3 times. _____Yes _____No

10. Comments:_____________________________________________________________________

_________________________________________________________________________________

Download from Www.Somanuals.com. All Manuals Search And Download.

FOLD ALONG DOTTED LINE

Place

Stamp

Here

GRIZZLY INDUSTRIAL, INC.

P.O. BOX 2069

BELLINGHAM, WA 98227-2069

FOLD ALONG DOTTED LINE

Send a Grizzly Catalog to a friend:

Name_______________________________

Street_______________________________

City______________State______Zip______

TAPE ALONG EDGES--PLEASE DO NOT STAPLE

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTY AND RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from

the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,

negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty

and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-

ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent

that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.

In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and

any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.

We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,

or consequential damages arising from the use of our products.

To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then

issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the

carton. We will not accept any item back without this number. Proof of purchase must accompany the

merchandise.

The manufacturers reserve the right to change specifications at any time because they constantly strive to

achieve better quality equipment. We make every effort to ensure that our products meet high quality and

durability standards and we hope you never need to use this warranty.

Please feel free to write or call us if you have any questions about the machine or the manual.

Thank you again for your business and continued support. We hope to serve you again soon.

Download from Www.Somanuals.com. All Manuals Search And Download.

Grizzly Sander G0459 User Manual
Haier CRT Television HTX25S31 HTX29S31S HTX34S31 User Manual
Hamilton Beach Blender 840083100 User Manual
Hamilton Beach Toaster 22408 User Manual
HANNspree Flat Panel Television ST08 10A1 User Manual
Hasbro Robotics 07935 07145 User Manual
HP Hewlett Packard Power Supply 6259B User Manual
HTC Cell Phone NIKI100 User Manual
Huffy Fitness Equipment AR410W User Manual
IBM Switch 12122EA6 User Manual