INSTRUCTIONS-PARTS LIST
306–993
Rev. D
Supersedes Rev. B
and PCN C
This manual contains important
warnings and information.
READ AND KEEP FOR REFERENCE.
First choice when
quality counts.t
INSTRUCTIONS
Hydra-Clean) Pressure Washers
42 bar, 4.2 MPa (600 psi) Maximum Working Pressure
For Mounting on Open 55 Gallon Supply Drum
(Can be wall mounted with accessory bracket)
Model 205–985, Series C
Includes 5:1 Ratio Monark Pump with Neoprene and
UHMWPE packings, drum mounting bracket, suction
hose, air line lubricator, 40 ft. spray hose,
Hydra–CleanR gun and spray tip.
Model 207–860, Series B
Includes 5:1 Ratio Monark Pump with UHMWPE and
PTFERpackings, drum mounting bracket, suction
hose and air line lubricator
.
06769A
CAUTION
The Graco warranty will not apply if abrasive or
corrosive materials, other than those Graco recom
mends are used with this unit.
-
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
ECOPYRIGHT 1996, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
INJECTION HAZARD
Spray from the gun, hose leaks, or ruptured components can inject fluid into your body and cause an
extremely serious injury, including the need for amputation. Splashing fluid in the eyes or on the skin
can also cause a serious injury
.
D
Fluid injected into the skin might look like just a cut, but it is a serious injury
cal attention.
.
Get immediate medi-
D
D
D
D
D
D
D
D
D
Do not point the spray gun at anyone or at any part of the body
.
Do not put hand or fingers over the spray tip.
Do not stop or deflect fluid leaks with your hand, body, glove, or rag.
Do not “blow back” fluid; this is not an air spray system.
Always have the tip guard and the trigger guard on the spray gun when spraying.
Check the gun diffuser operation weekly. Refer to the gun manual.
Be sure the gun trigger safety operates before spraying.
Lock the gun trigger safety when you stop spraying.
Follow the Pressure Relief Procedure on page 8 whenever you: are instructed to relieve pres
sure; stop spraying; clean, check, or service the equipment; and install or clean the spray tip.
-
D Tighten all the fluid connections before operating the equipment.
D
Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately.
Do not repair high pressure couplings; replace the entire hose.
D
Fluid hoses must have spring guards on both ends, to help protect them from rupture caused by
kinks or bends near the couplings.
MOVING PARTS HAZARD
Moving parts, such as the air motor piston, can pinch or amputate your fingers.
D
D
D
Keep clear of all moving parts when starting or operating the pump.
Never operate the pump with the air motor plates removed.
Before checking or servicing the equipment, follow the Pressure Relief Procedure on page 8 to
prevent the equipment from starting unexpectedly
.
306-993
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and re
sult in a fire or explosion and serious injury
-
.
D
D
Ground the equipment and the object being sprayed. Refer to Grounding on page 5.
If there is any static sparking or you feel an electric shock while using this equipment, stop spray-
ing immediately Do not use the equipment until you identify and correct the problem.
.
D
Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being sprayed.
D
D
D
D
D
Keep the spray area free of debris, including solvent, rags, and gasoline.
Electrically disconnect all equipment in the spray area.
Extinguish all open flames or pilot lights in the spray area.
Do not smoke in the spray area.
Do not turn on or off any light switch in the spray area while spraying or while operating if fumes
are present.
D
Do not operate a gasoline engine in the spray area.
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
D
D
Know the specific hazards of the fluid you are using.
Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.
D
Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer
.
4
306-993
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
3. Air and fluid hoses: use only electrically conductive
Grounding
hoses.
WARNING
FIRE AND EXPLOSION HAZARD
Before operating the pump, ground the
system as explained below. Also read
the section FIRE OR EXPLOSION
HAZARD on page 4.
4. Air compressor: follow manufacturer
dations.
’s recommen-
5. Spray gun: ground through connection to a prop
erly grounded fluid hose and pump.
-
Although water generally provides a natural electrical
ground, the following equipment must be grounded if
the cleaning chemical are volatile.
6. Fluid supply container: follow your local code.
7. Object being sprayed: follow your local code.
1. When cleaning in enclosed areas, such as storage
tanks, locate the pump and air compressor outside
the area and well away from it. Provide adequate
ventilation. If the area you are cleaning has stored
flammable materials. take appropriate precautions
to avoid static sparking. Consult your local codes.
8. Solvent pails used when flushing: follow your local
code. Use only metal pails, which are conductive,
placed on a grounded surface. Do not place the
pail on a nonconductive surface, such as paper or
2. Pump: use a ground wire and clamp. See Fig. 1.
Loosen the grounding lug locknut (W) and washer
(X). Insert one end of a 1.5 mm@ (12 ga) minimum
ground wire (Y) into the slot in lug (Z) and tighten
the locknut securely. Connect the other end of the
wire to a true earth ground. Order Part No.
cardboard, which interrupts the grounding continu
ity.
-
237–569 Ground Wire and Clamp.
9. To maintain grounding continuity when flushing or
relieving pressure, hold a metal part of the spray
gun firmly to the side of a grounded metal pail,
then trigger the gun.
W
X
Y
Z
General Information
The typical setup shown in Figure 2 is only a guide to
selecting and installing required and optional compo
nents. For assistance in designing a system to suit
-
0864
Fig. 1
your needs, contact your Graco representative. Refer
to Figure 2 for callouts in parentheses.
306-993
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
3. Connect the air line lubricator (G) to the pump air
Connect Hoses and Mount Pump
inlet using pipe sealant. Install a pump air bleed
valve (H) and air regulator and gauge (J) to the air
line lubricator. Connect an air line filter (K) to the
regulator. From the air line filter, install an air drain
valve (L), bleed–type air valve (M), and connect to
the air supply using electrical conductive air supply
hose (N).
Connect hoses and pump as follows:
NOTE: This pump is supplied with a bracket (D) which
holds it to the side of a drum. If you want to install the
pump on a wall, do not install the hanging bracket. Use
Graco Wall Mounting Bracket 206–778 or equivalent
for wall setup.
1. Screw the hose stud (A) of the suction hose (B)
into the pump’s intake housing (C) using LoctiteR
Pipe Sealant. Assemble the hanging bracket (D) to
the pump with the screw, lockwasher, and nut (E)
provided.
4. Close to the pump’s 1/2 npt(f) fluid outlet, install a
tee (P) and a fluid drain valve (R). Then install a
fluid hose (S) and Hydra–Clean gun (T). The hose
and gun are supplied with Model 205–985, but
must be purchased separately for Model 207–860.
2. Remove the ball valve (17, see Parts) from Model
205–985. It is not used in this setup. Hang the
pump on your empty cleaning solution drum.
CAUTION
Oils containing phosphate ester or chlorinated hydro
carbons are not compatible with the plastic bowl of
the lubricator – be sure that oil used to lubricate the
compressor is free of these additives.
-
NOTE: A pump runaway valve (F) may be installed
near the pump air inlet. This valve senses when the
pump is running too fast and shuts off the air to the
pump.
6
306-993
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
KEY
A
B
C
D
E
F
Barbed Hose Stud
Suction Hose
Pump Intake housing
Bracket
Screw, Lockwasher, and Nut
Pump Runaway Valve
Air Line Lubricator
Pump Air Bleed Valve
(required, for pump)
J
K
L
Air Regulator and Gauge
Air Line Filter
Air Line Drain Valve
Bleed–type Air Valve
(for accessories)
Electrically Conductive Air Supply Hose
Tee
Fluid Drain Valve (provided)
S
T
Spray Fluid Hose (supplied with
205–985)
Hydra–Clean Gun (supplied with
205–985)
M
U
V
Filter
N
P
R
Ground Wire (required; see page 5 for
installation instructions)
G
H
K
J
N
H
F
E
M
L
G
V
C
P
R
T
A
E
U
S
D
B
06770A
306-993
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
1. Lock the gun trigger safety
.
General Information
2. Close the bleed-type master air valve (H, required
in your system)
The following instructions are for operation of the
Monark 5:1 Ratio Hydra–Clean Pressure Washers
Model 205–985 and Model 207–860. Callouts in
parentheses refer to Figure 2.
3. Unlock the gun trigger safety
.
4. Hold a metal part of the gun firmly to the side of a
grounded metal pail, and trigger the gun to relieve
pressure
Pressure Relief Procedure
WARNING
5. Lock the gun trigger safety
.
INJECTION HAZARD
Fluid under high pressure can be in
jected through the skin and cause
6. Open the drain valve (R, required in your system),
having a container ready to catch the drainage.
-
serious injury. To reduce the risk of an
injury from injection, splashing fluid, or moving
parts, follow the Pressure Relief Procedure
whenever you:
7. Leave the drain valve open until you are ready to
spray again.
If you suspect that the spray tip or hose is completely
clogged, or that pressure has not been fully relieved
after following the steps above, very slowly loosen the
tip guard retaining nut or hose end coupling and relieve
pressure gradually, then loosen completely. Now clear
the tip or hose.
D
D
D
D
are instructed to relieve the pressure,
stop spraying,
check or service any of the system equipment,
or install or clean the spray nozzles.
8
306-993
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Hold the spray nozzle about 2 feet (0.6 m) from the
surface you are cleaning and mist-wet it completely
WARNING
o avoid serious injury, including fluid injection and
splashing in the eyes or on the skin, never point the
gun at yourself or anyone else.
.
Let it soak briefly, then use the spray to “chisel” the dirt
off. Keep the nozzle at an angle, about 6 in. (150 mm)
from the surface. If some dirt remains, wet the surface
again. Let the object soak a little longer, then hold the
nozzle as close as possible and spray to blast the dirt
off.
T
Before Using
See Fig. 2. Prepare cleaning solution as instructed,
observing all safety precautions. Pre-mix powered
cleaners in a separate bucket of hot water before
adding to water in the supply drum.
After the dirt is removed, through rinse off the remain
-
ing solution with clear, cold water. When you are done
cleaning, close the pump air bleed valve and relieve
the pressure.
WARNING
ake care not to get spray containing cleaning
Shutdown and Care of Unit
T
chemicals into your eyes, ears, or nose. If any
spray does get on your skin or in your eyes, flush
immediately and thoroughly with water. Seek
immediate medical attention.
CAUTION
To reduce the risk of damaging your pump. never
allow the pump to run dry of fluid. Keep liquid in the
Open the bleed–type air valve (M), hold the spray
valve trigger (T) open and slowly open the pump air
bleed valve (H) until the pump is running slowly. After
solution is coming from the spray nozzle, open the
pump air bleed valve all the way and adjust the air line
lubricator (G) to deliver about 1 drop per minute. Refer
to the separate lubricator instruction manual.
container to prevent the pump from running away
.
WARNING
T
o reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
Release the spray valve trigger and let the pump run.
NOTE: Protect surfaces that might be damaged by the
cleaning solution and rinse off before the solution
dries. For removing stubborn dirt, use a strong, heated
solution.
When shutting down for the day or weekend, shut of
both the bleed–type air valve and pump air bleed
valve. Relieve the pressure. Rinse off any solution
f
remaining on equipment with clear, cold water. Shut of
f
the water supply valve and relieve the water pressure.
Useful Hints
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
After shutdown, check the air line lubricator (G) often
and keep it filled with oil. Also check the pump packing
nut regularly and keep it just tight enough to stop
leakage, but no tighter. Use a 1/4 in. diameter rod to
tighten.
306-993
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Before servicing this equipment always make sure to
relieve the pressure
WARNING
.
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
Note: Check all possible problems and solutions
before disassembling.
Problem
Cause
Solution
Obstructed spray tip, valve, or hose
Cleaning solution supply empty
Clean, clear
Refill
Excessive surge at spray nozzle
Clogged intake filter, kinked or col
lapsed suction hose
-
Clean, unkink
Fluid leaking from valve
Loose packing nut or worn packings
alve not adjusted properly
See manual 307–010
See manual 307–010
V
Valve will not stop dispensing
Dirty or worn valve stem or seat
Clean, clear, or replace – See manual
307–010
Cleaning solution supply empty
Refill
Valve will not stop the pump
Clogged intake filter, kinked or col
lapsed suction hose
-
Clean, unkink
Dirty or worn valve stem or seat
Clean clear, or replace – See manual
307–010
Dirty or worn fluid piston or packings
Dirty or worn fluid piston or packings
Service – See pump manual
Service – See pump manual
Pump operating, but spray pres
sure low on up stroke.
-
-
-
Pump operating, but spray pres
sure low on down stroke
Dirty or worn fluid intake valve
Clean, clear, or replace – See pump
manual
Clogged intake filter, kinked or col
lapsed suction hose
-
Clean, unkink
Pump operating, but spray pres
sure low on both strokes
Dirty or worn fluid piston or packings
Dirty or worn fluid intake valve
Service – See pump manual
Clean, clear, or replace – See pump
manual
Loose packing nut or worn packings
Restricted air line
Tighten, replace – See pump manual
Check for closed valve; use larger
supply hose
Fluid will not come from pump
(hose removed)
Pump throat packing nut too tight
Pump air motor not working
Restricted air line
Loosen
Service – See pump manual
Check for closed valve; use larger
supply hose
System will not spray
Pump air motor not working
Service – See pump manual
10
306-993
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
T
o manually lubricate the motor, disconnect the air line
General
at the motor and place 10 to 15 drops of oil in the inlet.
Reconnect the air line and turn on the air to blow oil
into the motor. Shut off the air supply to the pump and
relieve the pressure.
WARNING
T
o reduce the risk of serious injury whenever you
Proper packing nut take-up will stop leakage. However
all the packings should be replaced after 1000 hours
of operation or delivery of 120,000 gallons of solution
at 2 gpm. Refer to separate pump manual.
,
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
Clean the air line filter regularly
.
See Parts illustration for referenced items. Shut off the
air supply to the pump and relieve the pressure
.
Remove the inlet filter (2) daily and clean it. Check it
for damage that may allow contaminants to enter the
pump, and replace if necessary
.
Check the air line lubricator often and keep it filled with
oil. Also check the pump packing nut regularly to keep
it just tight enough to stop leakage, but no tighter. Use
a 1/4 in. (6.3 mm) diameter rod to tighten.
Refer to the separate instruction manuals supplied with
the components of your system for complete trouble
shooting and service instructions.
-
306-993
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 207–860
Model 205–985
Monark Hydra-Clean
Monark Hydra-Clean
Ref
No.
Ref
No.
Part No.
Description
Qty.
Part No.
Description
Qty.
1
2
3
214–847
206–300
224–345
AIR LINE LUBRICATOR
FILTER, fluid intake
5:1 Ratio Monark Pump
See manual 308–117 for parts
BUSHING, hex; 1/2 npt; 1/4 npt thd
size
SCREW, hex cap; 1/4–20 thd size;
3/4” (19mm) long
LOCKWASHER, spring; 1/4 screw
size
LOCKNUT, hex; 1/4–20 thd size
CLAMP, hose; self–tightening
ELBOW, 90_ street; 3/8 npt size
UNION, street swivel; 3/8 npt(m)
x 1.2 npt(f); thd size
1
1
1
2*
3
214–847
206–300
224–343
AIR LINE LUBRICATOR
FILTER, fluid intake
5:1 Ratio Monark Pump
See manual 308–116 for parts
BUSHING, hex; 1/2 npt; 1/4 npt thd
size
SCREW, hex cap; 1/4–20 thd size;
3/4” (19mm) long
LOCKWASHER, spring; 1/4 screw
size
LOCKNUT, hex; 1/4–20 thd size
CLAMP, hose; self–tightening
ELBOW, 90_ street; 3/8 npt size
NIPPLE; hex; 3/8 npt(mbe); 3–5/8”
(92 mm) long
UNION, street swivel; 3/8 npt(m)
x 1.2 npt(f); thd size
HOSE, plastic; 3/4” (19mm) ID;
29” (.74 m) long
1
1
1
1
1
1
1
1
4
5
6
102–022
102–023
102–024
4
5
6
102–022
102–023
104–024
1
1
2
1
1
1
2
1
7
8
9
11
102–025
102–123
155–494
162–505
7
8
9
10
102–025
102–123
155–699
160–790
1
1
1
12
162–950
HOSE, plastic; 3/4” (19mm) ID;
29” (.74 m) long
11
12
162–505
162–950
1
1
1
13
14
15
164–085
165–280
205–174
SPRING, reinforcing; plastic hose
BRACKET, pump mounting
HOSE, fluid coupled, 1/4 npt(mbe);
1/4” ID; 40 ft. (12.2m) long
HYDRA–CLEANR GUN
See 307–010 for parts
1
1
1
1
13
14
22
164–085
165–280
102–550
SPRING, reinforcing; plastic hose
BRACKET, pump mounting
STUD, barbed hose; 3/8 npt(m)
1
1
1
16
17
18
237–485
208–393
162–980
BALL VALVE
See 307–068 for parts
NOZZLE, spray; 0.062 orifice;
50_ fan angle
1
1
19
20
162–981
164–017
GUARD, spray nozzle
TUBE, spray; 1/4 npt(m)
10” (254mm) long
BUSHING; 3/8 npt(m) x 1/4 npt(f)
STUD, barbed hose; 3/8 npt(m)
SWIVEL, sst, 1/2 npt(m) x 1/2 npt(f)
1
1
1
1
21
22
23
168–160
102–550
114–190
306-993
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Stainless Steel Spray Tips
AIR SUPPLY TO PUMP
70 PSI
(4.8 bar, 0.48 MPa)
100 psi
(7 bar, 0.7 MPa)
TIP
NO.
ORIFICE
SIZE
SPRAY
ANGLE
GPM CFM
WP
GPM CFM
WP
164–435
160–964
164–434
164–436
164–438
160–963
.043
.043
.052
.052
.052
.062
40
25
25
40
65
25
1.6
2.3
17
23
610
560
1.8
2.6
24
32
840
750
KEY:
GPM : Gallons Per Minute
CFM : Cubic Feet Per Minute
PSI : Pounds Per Square Inch
WP : Working Pressure in PSI
Stainless Steel Blasting Tips
TIP NO.
102–442
102–444
102–446
102–450
ORIFICE SIZE
.067
.078
.086
.125
14
306-993
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
11.75”
(298 mm)
24.5”
(622 mm)
06771
Technical Data
Air pressure range
Air volume requirements
Pump ratio
Max. recommended pump speed
.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 to 120 psi (2.8 to 8.4 bar, .28 to .84 MPa)
3
.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2 cfm (0.23 m /min.) at 100 psi (7 bar, 0.7 MPa),
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5:1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 cycles per min.
.
.
Pump discharge pressure
Weight
.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600 psi (41.4 bar, 4.14 MPa)
27 lb (12.26 kg) Model 207–860
37 lb (16.80 kg) Model 205–985
Maximum operating temperature of fluid pump.
.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480_F (249_C)
Maximum operating temperature of air motor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200_F (90_C)
Loctiter is registered trademarks of the Loctite Corp.
is registered trademarks of the DuPont Co.
PTFE
306-993
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from
defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. With the
exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of
sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment
is installed, operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub
-
stitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS
WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD
BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches,
hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in mak
-
ing any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais
-
sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
Graco Phone Number
TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you:
1–800–367–4023
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Sales Offices: Minneapolis, Detroit, Los Angeles
Foreign Offices: Belgium, Canada, England, Korea, France, Germany, Hong Kong, Japan
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
PRINTED IN U.S.A. 306–993 November 1968, Revised September 1997
16
306-993
Download from Www.Somanuals.com. All Manuals Search And Download.
|