Graco Inc Power Roller 244278 User Manual

Instructions  
Important Safety Instructions  
Read all warnings and instructions in this manual.  
Save these instructions.  
311141A  
Frame, Roller  
- For application of architectural paints and coatings -  
Model 244278, Series A  
9 inch (23 cm) length  
7/8 inch inlet with 1/2 inch (13 mm) nap roller cover  
3000 psi (24.8 MPa, 248 bar) Maximum Working Pressure*  
*The best operating pressure is the lowest pressure that pro-  
vides an even paint supply to the roller and typically does not  
exceed 300 psi (2.1 MPa, 21 bar).  
ti6623ab  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pressure Relief Procedure  
Pressure Relief Procedure  
If you suspect the spray tip or hose is clogged or that  
pressure has not been fully relieved after following the  
steps above, VERY SLOWLY loosen tip guard retaining  
nut or hose end coupling to relieve pressure gradually,  
then loosen completely. Clear hose or tip obstruction.  
Follow this Pressure Relief Procedure when you stop  
spraying and before cleaning, checking, servicing, or  
transporting equipment.  
Trigger Lock  
Always engage the trigger  
lock when you stop spray-  
ing to prevent the gun from  
being triggered acciden-  
tally by hand or if dropped  
or bumped.  
1. Turn power switch OFF and  
unplug sprayer power cord.  
WLꢀꢁꢂꢃD  
TIꢀꢄꢅꢃA  
2. Turn spray/prime valve to  
PRIME to relieve pressure.  
Installation  
35,0(  
3. Hold metal part of gun firmly  
to side of a grounded metal  
pail. Trigger gun.  
Do not modify the extension tube or roller frame or use  
parts not designed for this equipment.  
Gasket (12) must be in place before installing frame  
(1). If gasket is not in place there is a potential injection  
hazard which could result in serious injury.  
TIꢀꢁꢂꢃAB  
Refer to your sprayer and spray gun instruction manu-  
als for safe operation of this frame.  
4. Engage trigger lock.  
1. Follow pressure relief procedure.  
2. Prime pump (refer to your sprayer operation manual  
for this procedure).  
3. Install roller frame.  
TIꢀꢄꢅꢃA  
311141A  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Cleaning  
Cleaning  
This is the procedure for flushing/cleaning the pressure  
roller. The sprayer and gun you are using may have ad-  
ditional flushing/cleaning instructions; such as cleaning  
filters and screens. See sprayer and gun operation man-  
uals.  
c. Pull end caps (2 & 4) off diffuser (23).  
3. Clean roller cover (19), caps (2 & 4) and diffuser  
(23) with water or a compatible fluid for oil-based  
materials.  
Leave pressure roller attached to gun for  
this procedure.  
Refer to roller parts drawing, page  
4. Place roller frame (1) in paint pail. Be sure the holes  
in roller frame (1) are facing inside paint pail.  
5. Prime pump with water or flushing fluid for oil-based  
materials. Use the lowest pump pressure setting.  
6. Turn prime/spray valve to SPRAY.  
1. Relieve pressure, page 3.  
Perform Step 7 at the lowest pressure possible.  
2. Remove roller cover (19) and diffuser (23) from  
roller frame (1) as follows:  
7. Trigger gun until flushing fluid begins to dilute the  
paint.  
a. Using your thumb, press down on clip (5) to  
release end caps (3 & 9), diffuser, (23) and  
roller cover (19) into pail.  
8. Place roller frame (1) in another bucket and con-  
tinue flushing until fluid coming out of roller frame (1)  
is clear.  
b. Remove roller cover (19) from diffuser (23).  
9. Shut off pump. Turn prime/spray valve to PRIME.  
4
311141A  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts  
Parts  
23  
Ref.  
No. Part No. Description  
Qty.  
4
1
2
15B052 FRAME, roller  
245999 CAP, end (includes seal and  
retainer)  
1
1
1
4
246277 CAP, end (includes seal, retainer,  
and o-ring)  
1
5
6
9
197106 CLIP, roller  
197118 FITTING, swivel  
197117 NUT, retaining  
1
1
1
1
5
19  
7722  
ROLLER, cover, 9-inch, 1/2 inch  
(13mm) nap  
2
20  
23  
115524 GASKET  
15B065 DIFFUSER  
1
2
TIꢂꢂꢄꢀAB  
Replacement Danger and Warning labels, tags, and  
19  
9
cards are available at no cost.  
20  
6
Roller Covers  
Part No. Description  
Qty  
7722  
7723  
7724  
9 inch x 1/2 inch nap  
6
6
6
9 inch x 3/4 inch nap  
9 inch x 1-1/4 inch nap  
Wetted Parts:  
Fluoroelastomer, nylon, plated steel, acetal, polyethyl-  
ene, stainless steel.  
311141A  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASM Standard Warranty  
ASM Standard Warranty  
ASM warrants all equipment referenced in this document which is manufactured by ASM and bearing its name to be free from defects in material  
and workmanship on the date of sale by an authorized ASM distributor to the original purchaser for use. With the exception of any special,  
extended, or limited warranty published by ASM, ASM will, for a period of twelve months from the date of sale, repair or replace any part of the  
equipment determined by ASM to be defective. This warranty applies only when the equipment is installed, operated and maintained in  
accordance with ASM’s written recommendations.  
This warranty does not cover, and ASM shall not be liable for general wear and tear, or any malfunction damage or wear caused by faulty  
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of  
non-ASM component parts. Nor shall ASM be liable for malfunction, damage, or wear caused by the incompatibility of ASM equipment with  
structures, accessories, equipment or materials not supplied by ASM, or the improper design, manufacture, installation, operation or maintenance  
of structures, accessories, equipment or materials not supplied by ASM.  
This warranty is conditioned up the prepaid return of the equipment claimed to be defective to an authorized ASM distributor for verification of the  
claimed defect. If the claimed defect is verified, ASM will repair or replace free of charge any defective parts. The equipment will be returned to the  
original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be  
made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.  
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED  
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
ASM’s sole obligation and buyer’s sole remedy for any breach of warranty shall be set forth above. The buyer agrees that no other remedy  
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or  
consequential loss) shall be available. Any action or breach of warranty must be brought within two (2) years of the date of sale.  
ASM MAKES NOT WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT  
MANUFACTURED BY ASM. These items sold, but not manufactured by ASM (such as electric motors, switches, hose, etc.), are subject to the  
warranty, if any, of their manufacturer. ASM will provide purchaser with reasonable assistance in making any claim for breach of these warranties.  
In no event will ASM be liable for indirect, incidental, special or consequential damages resulting from ASM supplying equipment hereunder, or the  
furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the  
negligence of ASM, or otherwise.  
TO PLACE AN ORDER OR FOR SERVICE, contact your ASM distributor,  
or call 1-800-285-0032.  
All written and visual data contained in this document reflects the latest product information available at the time of publication.  
ASM reserves the right to make changes at any time without notice.  
Manufactured by ASM Company; a division of Graco Inc.  
ASM Company, 3500 North 1st Avenue, Sioux Falls, SD 57104  
PRINTED IN U.S.A. 311141  
4/2006  
6
311141A  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Haier Water Heater FCD JTHC80A III E FCD JTHC100A IIIE User Manual
HannsG Computer Monitor HQ 191DPB User Manual
HANNspree Laptop SN12E2 User Manual
Harbor Freight Tools Model Vehicle 90139 User Manual
Hayter Mowers Lawn Mower 111 2842 Rev B User Manual
Heatcraft Refrigeration Products Humidifier CH B 01 User Manual
Hotpoint Cooktop CH50GCIK User Manual
Husqvarna Lawn Mower 36 EL User Manual
Husqvarna Lawn Mower YTH2248 User Manual
IBM Computer Drive 07N4108 User Manual