Operation
313539F
ENG
H-VR
Hydraulic Variable Ratio, Heated, Plural Component Proportioner. For spraying
polyurethane foam and polyurea coatings. For professional use only.
Not for use in explosive atmospheres.
U.S. Patent Pending
Russian Patent No. 2359181
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
ing pressure.
r_256886_313359_1A
ꢀꢀꢁꢂꢃꢄꢅ
#ONFORMS TO !.3)ꢀ5,
3TDꢁ ꢂꢃꢃ #ERTIFIED TO
#!.ꢀ#3! 3TDꢁ
#ꢄꢄꢁꢄ .Oꢁ ꢅꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplied Manuals
Circulation Kit
Supplied Manuals
Part
Description
™
The following manuals are shipped with the Reactor
H-VR Proportioner. Refer to these manuals for detailed
equipment information.
309818
Instruction-Parts Manual
(English)
Circulation Valve Kit
Order Part 15M334 for a compact disk of Reactor manu-
als translated in several languages.
Part
Description
312070
Instruction-Parts Manual
(English)
Reactor Hydraulic Proportioner
Data Reporting Kit
Part
313540
Description
Part
Description
Reactor H-VR Proportioner,
Repair-Parts Manual (English)
309867
Instruction-Parts Manual
(English)
Reactor Electrical Diagrams
Rupture Disk Assembly Kit
Part
312064
Description
Part
Description
Reactor Hydraulic Proportioner, Electri-
cal Diagrams (English)
309969
Instruction-Parts Manual
(English)
Fluid Pump
Proportioning Pump Repair Kits
Part Description
312071
Part
Description
313485
H-VR Pump Instructions-Parts Manual
(English)
Seal Kits Instruction-Parts Manual
(English)
Related Manuals
The following manuals are for accessories used with the
Reactor™.
Feed Pump Kits
Part
Description
309815
Instruction-Parts Manual
(English)
Air Supply Kit
Part
Description
309827
Instruction-Parts Manual
(English) for Feed Pump Air Supply Kit
Circulation and Return Tube Kits
Part
Description
309852
Instruction-Parts Manual
(English)
Heated Hose
Part
Description
309572
Instruction-Parts Manual
(English)
313539F
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-
tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back
to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where
applicable.
WARNING
ELECTRIC SHOCK HAZARD
This equipment must be grounded. Improper grounding, setup, or usage of the system can cause elec-
tric shock.
•
•
•
•
•
Turn off and disconnect power cord before servicing equipment.
Use only grounded electrical outlets.
Use only 3-wire extension cords.
Ensure ground prongs are intact on power and extension cords.
Do not expose to rain. Store indoors.
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or
swallowed.
•
•
•
•
Read MSDS’s to know the specific hazards of the fluids you are using.
Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
Always wear impervious gloves when spraying or cleaning equipment.
If this equipment is used with isocyanate material, see additional information on isocyanites in Isocy-
anate Conditions Section of this manual.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in the operating
area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic
fumes, burns, and hearing loss. This equipment includes but is not limited to:
•
•
•
•
Protective eyewear
Clothing and respirator as recommended by the fluid and solvent manufacturer
Gloves
Hearing protection
SKIN INJECTION HAZARD
High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just
a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.
•
•
•
•
•
•
Do not point gun at anyone or at any part of the body.
Do not put your hand over the spray tip.
Do not stop or deflect leaks with your hand, body, glove, or rag.
Do not spray without tip guard and trigger guard installed.
Engage trigger lock when not spraying.
Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning,
checking, or servicing equipment.
4
313539F
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
WARNING
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent
fire and explosion:
•
•
Use equipment only in well ventilated area.
Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop
cloths (potential static arc).
•
•
Keep work area free of debris, including solvent, rags and gasoline.
Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes
are present.
•
•
•
•
Ground all equipment in the work area. See Grounding instructions.
Use only grounded hoses.
Hold gun firmly to side of grounded pail when triggering into pail.
If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment
until you identify and correct the problem.
•
Keep a working fire extinguisher in the work area.
PRESSURIZED ALUMINUM PARTS HAZARD
Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids
containing such solvents in pressurized aluminum equipment. Such use can cause serious chemical
reaction and equipment rupture, and result in death, serious injury, and property damage.
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
•
•
Do not operate the unit when fatigued or under the influence of drugs or alcohol.
Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component. See Technical Data in all equipment manuals.
•
•
Do not leave the work area while equipment is energized or under pressure. Turn off all equipment
and follow the Pressure Relief Procedure in this manual when equipment is not in use.
Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu-
facturer’s replacement parts only.
•
•
•
•
•
•
Do not alter or modify equipment.
Use equipment only for its intended purpose. Call your distributor for information.
Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
Do not kink or over bend hoses or use hoses to pull equipment.
Keep children and animals away from work area.
Comply with all applicable safety regulations.
MOVING PARTS HAZARD
Moving parts can pinch or amputate fingers and other body parts.
•
•
•
Keep clear of moving parts.
OR
Do not operate equipment with protective guards or covers removed.
Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,
follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.
BURN HAZARD
Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid severe
burns:
•
•
Do not touch hot fluid or equipment.
Wait until equipment/fluid has cooled completely.
313539F
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Isocyanate Conditions
Isocyanate Conditions
Moisture Sensitivity of
Isocyanates
Isocyanates (ISO) are catalysts used in two component
foam and polyurea coatings. ISO will react with moisture
(such as humidity) to form small, hard, abrasive crystals,
which become suspended in the fluid. Eventually a film
will form on the surface and the ISO will begin to gel,
increasing in viscosity. If used, this partially cured ISO
will reduce performance and the life of all wetted parts.
Spraying materials containing isocyanates creates
potentially harmful mists, vapors, and atomized partic-
ulates.
Read material manufacturer’s warnings and material
MSDS to know specific hazards and precautions
related to isocyanates.
Prevent inhalation of isocyanate mists, vapors, and
atomized particulates by providing sufficient ventila-
tion in the work area. If sufficient ventilation is not
available, a supplied-air respirator is required for
everyone in the work area.
NOTE:
The amount of film formation and rate of crystallization
varies depending on the blend of ISO, the humidity, and
the temperature.
To prevent contact with isocyanates, appropriate per-
sonal protective equipment, including chemically
impermeable gloves, boots, aprons, and goggles, is
also required for everyone in the work area.
To prevent exposing ISO to moisture:
•
Always use a sealed container with a desiccant
dryer in the vent, or a nitrogen atmosphere. Never
store ISO in an open container.
Material Self-ignition
•
•
Use moisture-proof hoses specifically designed for
ISO, such as those supplied with your system.
Never use reclaimed solvents, which may contain
moisture. Always keep solvent containers closed
when not in use.
Some materials may become self-igniting if applied
too thickly. Read material manufacturer’s warnings
and material MSDS.
•
•
•
Never use solvent on one side if it has been contam-
inated from the other side.
Keep Components A and
B Separate
Always park pumps when you shutdown, see page
30.
Always lubricate threaded parts, except for GC1128,
GC0518, GC0697, and GC2150, with Part 217374
ISO pump oil or grease when reassembling.
Cross-contamination can result in cured material in
fluid lines which could cause serious injury or damage
equipment. To prevent cross-contamination of the
equipment’s wetted parts, never interchange compo-
nent A (isocyanate) and component B (resin) parts.
Foam Resins with 245 fa
Blowing Agents
Some foam blowing agents will froth at temperatures
above 90°F (33°C) when not under pressure, especially
if agitated. To reduce frothing, minimize preheating in a
circulation system.
6
313539F
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Materials
Changing Materials
•
When changing materials, flush the equipment mul-
tiple times to ensure it is thoroughly clean.
•
•
Always clean the fluid inlet strainers after flushing.
Check with your material manufacturer for chemical
compatibility.
•
•
Most materials use ISO on the A side, but some use
ISO on the B side.
Epoxies often have amines on the B (hardener)
side. Polyureas often have amines on the B (resin)
side.
313539F
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Typical Installation, with circulation
Typical Installation, with circulation
G
J
K
L
M
P
R
S
T
Feed Pump Air Supply Lines
Fluid Supply Lines
Feed Pumps
Key for FIG. 1
A
B
C
D
E
F
Reactor H-VR Proportioner
Heated Hose
Fluid Temperature Sensor (FTS)
Heated Whip Hose
Fusion Spray Gun
Agitator
Desiccant Dryer
Gun Fluid Manifold (part of gun)
Circulation Lines
Fluid Inlet
Gun Air Supply Hose
Hose Manifold
A Side Supply Detail
B Side Supply Detail
M
M
K
K
K
G
G
L
K
ti7820a 3
ti7820a 2
R
R
A
J
S
T
J
D
T
F
E
P
S
C*
r_256886_313359_1A
*Shown exposed for clarity.
Wrap with tape during operation.
B
ti10000a
FIG. 1: Typical Installation, with circulation
8
313539F
Download from Www.Somanuals.com. All Manuals Search And Download.
Typical Installation, without circulation
Typical Installation, without circulation
H
J
K
L
M
N
P
S
T
Waste Containers
Fluid Supply Lines
Feed Pumps
Agitator
Desiccant Dryer
Bleed Lines
Gun Fluid Manifold (part of gun)
Fluid Inlet
Hose Manifold
Key for FIG. 2
A
B
C
D
E
F
Reactor H-VR Proportioner
Heated Hose
Fluid Temperature Sensor (FTS)
Heated Whip Hose
Fusion Spray Gun
Gun Air Supply Hose
Feed Pump Air Supply Lines
G
B Side Supply Detail
A Side Supply Detail
K
K
M
K
G
G
L
K
ti7821a 2
ti7821a 3
J
A
S
T
F
S
J
D
N
H
T
E
P
C*
r_256886_313359_1A
*Shown exposed for clarity.
Wrap with tape during operation.
B
ti10001a
FIG. 2: Typical Installation, without circulation
313539F
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Component Identification
Component Identification
NOTICE
To prevent damage to soft key buttons, do not press
the buttons with sharp objects such as pens, plastic
cards, or fingernails.
Reactor H-VR
Key for FIG. 3
BA Component A Pressure Relief Outlet
BB Component B Pressure Relief Outlet
EC Heated Hose Electrical Connector
EM Electric Motor, Fan, and Belt Drive (behind shroud)
FA Component A Fluid Manifold Inlet (on left side of manifold
block)
FB Component B Fluid Manifold Inlet
FH Fluid Heater (behind shroud)
FM Reactor Fluid Manifold
FV Fluid Inlet Valve (B side shown)
GA Component A Outlet Pressure Gauge
GB Component B Outlet Pressure Gauge
HA Component A Hose Connection
HB Component B Hose Connection
HC Hydraulic Pressure Control
HP Hydraulic Pressure Gauge
LR ISO Lube Pump Reservoir
MC Motor Control Display
MP Main Power Switch
OP Overpressure Rupture Disk Assembly (on rear of A and B
pumps)
RS Red Stop Button
SA Component A PRESSURE RELIEF/SPRAY Valve
SB Component B PRESSURE RELIEF/SPRAY Valve
SC Fluid Temperature Sensor Cable
SN Serial Number Plate (one inside cabinet, one on right side
of cabinet)
SR Electrical Cord Strain Relief
TA Component A Pressure Transducer (behind gauge GA)
TB Component B Pressure Transducer (behind gauge GB)
TC Temperature Control Display
TD Oil Cooler
10
313539F
Download from Www.Somanuals.com. All Manuals Search And Download.
Component Identification
MC
VR
TC
RS
HP
FM
HC
EM
OP
FV
SC
EC
SN
FH
MP
r_256886_313359_1A
SR
Detail of Reactor Fluid Manifold
(shroud removed for clarity)
TA
SA
GA
GB
TB
Detail of Serial No. Plate
(inside cabinet)
FA
SB
BA
FB
ti7823a
BB
HA
ti9880a
SN
HB
FIG. 3: Component Identification (15.3 kW Model Shown)
313539F
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Component Identification
Pump Assembly
AH Guard
AJ Clamping Knob
AK Lube Fitting
AL Ratio Lock Handle
AM Ratio Adjustment Wheel
AN Frame
AA Component A Pump
AB Component B Pump
AC Hydraulic Proportioner Pump
AD Yoke and Rod Guide Assembly
AE Pump Drive Link
AP Ratio Adjustment Screw
AF Pump Adapter
AG Pivot Bracket
AH
AJ
AB
Detail of Pump Assembly
(guard removed for clarity)
AG
AA
AM
AL
AE
AK
AD
AC
AK
(behind
pivot bracket)
AP
AF
AN
AB
FIG. 4: Front View of Pump Assembly
12
313539F
Download from Www.Somanuals.com. All Manuals Search And Download.
Temperature Controls and Indicators
Temperature Controls and Indicators
Heater Power Indicators
Heater Displays
A
B
Zone A Arrow Keys
Heater A On/Off Key
Zone B Arrow Keys
Heater B On/Off Key
Hose Zone Arrow Keys
Hose Heater On/Off Key
°F
Actual Temperature Key
Temperature Scale Keys
°C
Target Temperature Key
FIG. 5. Temperature Controls and Indicators
Main Power Switch
Actual Temperature Key/LED
Located on right side of unit, page 11. Turns Reactor
Press
to display actual temperature.
power ON
and OFF
. Does not turn
heater zones or pumps on.
Press and hold
to display electrical current.
Red Stop Button
Located between temperature control panel and motor
Target Temperature Key/LED
Press
to display target temperature.
control panel, page 11. Press to shut off motor
and heater zones only. Use main power switch to shut
off all power to unit.
Press and hold
to display heater control circuit
board temperature.
313539F
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Temperature Controls and Indicators
Temperature Scale Keys/LEDs
Circuit Breakers
°F
°C
Press
or
to change temperature scale.
Located inside Reactor cabinet.
Heater Zone On/Off Keys/LEDs
Ref.
CB1
CB2
CB3
CB4
CB5
Size
50 A
40 A
50 A
50 A
20 A
Component
Hose/Transformer Secondary
Transformer Primary
Heater A
Press
to turn heater zones on and off. Also clears
NOTE:
LEDs flash when heater zones are on. The duration of
each flash shows the extent that the heater is turned on.
Heater B
Motor/Pumps
Temperature Arrow Keys
Press
, then press
or
to adjust tem-
perature settings in 1 degree increments.
Temperature Displays
Show actual temperature or target temperature of
heater zones, depending on selected mode. Defaults to
actual at startup. Range is 32-190°F (0-88°C) for A and
B, 32-180°F (0-82°C) for hose.
CB1
CB2
CB3
CB4
ti9884a
CB5
For wiring and cabling, see repair manual 313540.
14
313539F
Download from Www.Somanuals.com. All Manuals Search And Download.
Motor Controls and Indicators
Motor Controls and Indicators
Pressure/Cycle Display
Arrow Keys
Motor ON/OFF Key
ON / OFF
PARK Key
PARK
Pressure Key
PSI/BAR Keys
Cycle Count Key
PSI
BAR
FIG. 6. Motor Controls and Indicators
Motor ON/OFF Key/LED
Pressure Key/LED
Press
to turn motor ON and OFF. Also clears
Press
to display fluid pressure.
NOTE:
If pressures are imbalanced, display shows higher of
two pressures.
PARK Key/LED
Press
at end of day to cycle component A pump
to home position, submerging displacement rod. Trigger
gun until pump stops. Once parked, motor will automati-
cally shut off.
PSI/BAR Keys/LEDs
PSI
BAR
Press
or
to change pressure scale.
313539F
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Spray Adjustments
•
Fluid pressure setting. Too little pressure results in
an uneven pattern, coarse droplet size, low flow,
and poor mixing. Too much pressure results in
excessive overspray, high flow rates, difficult control,
and excessive wear.
Cycle Count Key/LED
Press
to display cycle count.
NOTE:
•
•
•
Fluid temperature. Similar effects to fluid pressure
setting. The A and B temperatures can be offset to
help balance the fluid pressure.
To clear counter, press and hold
for 3 sec.
Mix chamber size. Choice of mix chamber is based
on desired flow rate, fluid viscosity, and selected
ratio.
Hydraulic Pressure Control
Knob
Use to adjust hydraulic pressure available to the hydrau-
lic drive system. Turn knob (HC) clockwise to increase
pressure and counterclockwise to decrease pressure.
Use hydraulic pressure gauge (HP, page 11) to view
hydraulic pressure.
Clean-off air adjustment. Too little clean-off air
results in droplets building up on the front of the
nozzle, and no pattern containment to control over-
spray. Too much clean-off air results in air-assisted
atomization and excessive overspray.
+
-
ti7731a
ti7732a
NOTE:
Component A and B outlet pressures will be higher than
the hydraulic set pressure, depending on the model.
Component A and B pressure may be viewed on the
pressure gauges (GA, GB), or the higher of the two
pressures may be displayed on the motor control panel
(MC). See FIG. 3, page 11.
Motor Control Arrow Keys
Use
or
to:
•
•
Spray Adjustments
Flow rate, atomization, and amount of overspray are
affected by four variables.
16
313539F
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Setup
2. General equipment guidelines
NOTICE
•
Determine the correct size generator. Using the cor-
rect size generator and proper air compressor will
enable the proportioner to run at a nearly constant
RPM. Failure to do so will cause voltage fluctuations
that can damage electrical equipment. Ensure the
generator matches the voltage and phase of the
proportioner.
Proper system setup, startup, and shutdown pro-
cedures are critical to electrical equipment reliabil-
ity. The following procedures ensure steady
voltage. Failure to follow these procedures will
cause voltage fluctuations that can damage electri-
cal equipment and void the warranty.
1. Locate Reactor
Use the following procedure to determine the cor-
rect size generator.
hole dimensions.
a. List system components that use peak load
requirements in watts.
b. Do not expose Reactor to rain.
b. Add the wattage required by the system compo-
nents.
NOTICE
c. Perform the following equation:
Bolt Reactor to original shipping pallet before lifting.
Total watts x 1.25 = kVA (kilovolt-amperes)
c. Use the casters to move Reactor to a fixed loca-
tion, or bolt to shipping pallet and move with
forklift.
d. Select a generator size that is equal to or
greater than the determined kVA.
•
•
•
Use proportioner power cords that meet or exceed
the requirements listed in Table 2. Failure to do so
will cause voltage fluctuations that can damage
electrical equipment.
d. To mount on a truck bed or tailer, remove cast-
ers and bolt directly to truck or trailer bed. See
Use an air compressor with constant speed head
unloading devices. Direct online air compressors
that start and stop during a job will cause voltage
fluctuations that can damage electrical equipment.
Maintain and inspect the generator, air compressor,
and other equipment per the manufacturer recom-
mendations to avoid an unexpected shutdown.
Unexpected equipment shutdown will cause voltage
fluctuations that can damage electrical equipment.
•
Use a wall power supply with enough current to
meet system requirements. Failure to do so will
cause voltage fluctuations that can damage electri-
cal equipment.
313539F
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
3. Electrical requirements
4. Connect electrical cord
See table 1.
NOTE:
Power cord is not suppled. See table 2.
Table 2: Power Cord Requirements
Installing this equipment requires access to parts
which may cause electric shock or other serious injury
if work is not performed properly. Have a qualified
electrician connect power and ground to main power
switch terminals, see step 3. Be sure your installation
complies with all National, State and Local safety and
fire codes.
Cord Specification
2
Part
Model
AWG (mm )
H-VR
4 (21.2), 3 wire + ground
256886
256887
H-VR
8 (8.4), 4 wire + ground
a. 230V, 3 phase: Using 5/32 or 4 mm hex allen
wrench, connect three power leads to L1, L2,
and L3. Connect green to ground (GND).
Table 1: Electrical Requirements (kW/Full Load
Amps)
Full
Load
Voltage
(phase)
Peak
Amps*
System
Watts**
Part
Model
GND
H-VR
230V (3)
400V (3)
71
41
26,600
26,600
256886
256887
H-VR
L1
L2
*
Full load amps with all devices operating at maxi-
mum capabilities. Fuse requirements at various flow
rates, ratios, and mix chamber sizes may be less.
** Total system watts, based on maximum hose length
for each unit, 410 ft (125 m) including whip hose.
ti2515b
b. 400V, 3 phase: Using 5/32 or 4 mm hex allen
wrench, connect three power leads to L1, L2,
and L3. Connect neutral to N. Connect green to
ground (GND).
GND
L1
L2
L3
ti3248b
NOTE:
The motor must rotate counter-clockwise when viewed
from shaft end. To reverse rotation, disconnect power
and reverse power leads L1 and L2.
18
313539F
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
to component A and B drums. See FIG. 1, page
8.
5. Connect feed pumps
a. Install feed pumps (K) in component A and B
supply drums. See FIG. 1 and FIG. 2, pages 8
and 9.
SB
SA
b. Seal component A drum and use desiccant
dryer (M) in vent.
c. Install agitator (L) in component B drum, if nec-
essary.
R
BA
R
ti9880a
d. Ensure A and B inlet valves (FV) are closed.
BB
b. Alternatively: Secure supplied bleed tubes (N)
in grounded, sealed waste containers (H). See
FIG. 2, page 9.
7. Install Fluid Temperature Sensor (FTS)
The Fluid Temperature Sensor (FTS) is supplied. Install
FTS between main hose and whip hose. See Heated
Hose manual 309572 for instructions.
FV
ti10971a
NOTE:
Supply hoses from feed pumps should be 3/4 in. (19
mm) ID.
e. Connect and tighten component A and B supply
hose to the 3/4 npt(f) swivel on the component A
and B inlet valve.
6. Connect pressure relief lines
Do not install shutoffs downstream of the PRESSURE
RELIEF/SPRAY valve outlets (BA, BB). The valves
function as overpressure relief valves when set to
SPRAY
. Lines must be open so valves can
automatically relieve pressure when machine is oper-
ating.
If circulating fluid back to the supply drums, use high
pressure hose rated to withstand the maximum work-
ing pressure of this equipment.
a. Recommended: Connect high pressure hose
(R) to relief fittings (BA, BB) of both PRES-
SURE RELIEF/SPRAY valves, Route hose back
313539F
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
bends. Wrap cable and electrical connections
with electrical tape.
8. Connect heated hose
NOTE:
See Heated Hose manual 309572 for detailed instruc-
tions on connecting heated hoses.
NOTE:
If spraying at a ratio other than 1:1, an E24 may occur.
Size hoses and mix chamber appropriately to avoid
pressure imbalance.
Y
V
NOTICE
The fluid temperature sensor (C) and whip hose (D)
length, including whip hose, must be 60 ft (18.3 m)
minimum.
ti9881a
9. Close gun fluid manifold valves A and B
a. Turn main power OFF
.
b. Assemble heated hose sections, FTS, and whip
hose.
c. Connect A and B hoses to A and B outlets on
Reactor fluid manifold (FM). Hoses are color
coded: red for component A (ISO), blue for com-
ponent B (RES). Fittings are sized to prevent
connection errors.
ti2411a
10. Connect whip hose to gun fluid manifold
Do not connect manifold to gun.
FM
N
A
P
ti2417a
11. Pressure check hose
B
See hose manual. Pressure check for leaks. If no leaks,
wrap hose and electrical connections to protect from
damage.
ti9878a
NOTE:
Manifold hose adapters (N, P) allow use of 1/4 in. and
3/8 in. ID fluid hoses. To use 1/2 in. (13 mm) ID fluid
hoses, remove adapters from fluid manifold and install
as needed to connect whip hose.
d. Connect cables (Y). Connect electrical connec-
tors (V). Be sure cables have slack when hose
20
313539F
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
12. Ground system
a. Reactor: is grounded through power cord. See
b. Spray gun: connect whip hose ground wire to
without whip hose.
c. Fluid supply containers: follow your local code.
d. Object being sprayed: follow your local code.
e. Solvent pails used when flushing: follow your
local code. Use only metal pails, which are con-
ductive, placed on a grounded surface. Do not
place pail on a nonconductive surface, such as
paper or cardboard, which interrupts grounding
continuity
f. To maintain grounding continuity when flushing
or relieving pressure, hold a metal part of spray
gun firmly to the side of a grounded metal pail,
then trigger gun.
13. Check hydraulic fluid level
a. Hydraulic reservoir is filled at the factory. Check
fluid level before operating the first time, and
313539F
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Startup
Startup
See table 3 for ratios with the one pump set at 1.0 and
available settings for the second pump.
Do not operate Reactor without all covers and shrouds
in place. Do not attempt to change ratio while machine
is pressurized or running. Do not loosen ratio lock
handle if A and B component pumps are pressurized
or while the pumps are operating.
Table 3: Ratio Range
Pump with higher
flow
Pump with lower
flow
Ratio
1:1
1.0
1.0
0.95
1.0
POSN #1
1.0
1.05
1. Select ratio
POSN #1
0.90
1.11:1
1.2:1
1.25:1
1.33:1
1.42:1
1.51:1
1.66:1
1.88:1
2:1
The stroke lengths of the fluid pumps (AA and AB) can
be adjusted to select the ratio. The frame (AN) has three
pin positions for the bottom of the pump and a slider
mechanism at the top of the pump, which allows for
positioning of the pump at any required position. This
allows for a a range of ratio settings between the first
and last settings on the pump drive link.
0.85
0.80
0.75
1.0
1.0
1.0
0.70
0.66
0.60
0.55
0.50
0.45
0.40
POSN #1
POSN #1
1.0
1.0
1.0
1.0
1.0
1.0
1.0
POSN #2
POSN #3
c. Loosen four clamping knobs (AJ) and remove
guard (AH).
2.22:1
2.5:1
AH
Pump A when viewed from rear of machine
AL
AJ
Pump B when viewed from rear of machine
AA
AB
r_256886_313359_6
FIG. 8: Pump Ratio Indicator Labels
FIG. 7: Front View
d. Use label on the pump drive link (AE) to identify
the correct position of the pump that needs to
22
313539F
Download from Www.Somanuals.com. All Manuals Search And Download.
Startup
e. Remove base pin (BP) from frame (AN) if the
AL
AF
AE
AM
TP
BP
AP
r_256886_313359_7
2 1
3
r_256886_313359_5
FIG. 9
f. Loosen ratio lock handle (AL) over the pump
that needs adjustment. Use a soft mallet to
loosen ratio lock handle if necessary. Turn ratio
adjustment wheel (AM) until the mark on the
pump adapter block (AF) lines up with the cor-
rect position on the ratio indicator label on the
pump drive link (AE).
1
2 3
FIG. 10
h. Ensure top of pump is in correct ratio position.
Tighten ratio lock handle (AL).
i. Install guard (AH) and tighten clamping knobs
g. Reinstall base pin (BP) if it was removed.
Ensure bottom of pump is in correct position.
NOTICE
Move bottom position of pump once top of pump
enters a new position #. Failure to adjust bottom
position of pump will damage the machine.
NOTE:
For highest volume of material: Ensure pump has lon-
gest stroke length. Set the pump with more flow closest
to hydraulic pump (AC) or at 1.0 to achieve maximum
313539F
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Startup
Open fluid valves A and B until clean, air-free
fluid comes from valves. Close valves.
2. Load fluid with feed pumps
NOTE:
The Reactor is tested with oil at the factory. Flush out
the oil with a compatible solvent before spraying. See
b. Turn on component B agitator, if used.
c. Turn both PRESSURE RELIEF/SPRAY valves
ti2484a
(SA, SB) to SPRAY
.
SB
SA
ti9877a
d. Start feed pumps.
e. Open fluid inlet valves (FV). Check for leaks.
FV
ti10972a
Do not mix components A and B during startup.
Always provide two grounded waste containers to
keep component A and component B fluids separate.
f. Use feed pumps to load system. Hold gun fluid
manifold over two grounded waste containers.
24
313539F
Download from Www.Somanuals.com. All Manuals Search And Download.
Startup
3. Set temperatures
desired temperature. Repeat for
zones.
and
B
A
B
NOTE:
For
zone only, if FTS is disconnected at startup,
display will show hose current (0A). See step j, page 26.
e. Press
to display actual temperatures.
°F
°C
Do not turn on hose heat without fluid in hoses.
f. Turn on
heat zone by pressing
.
Preheat hose (15-60 min). Indicator will flash
very slowly when fluid reaches target tempera-
ture. Display shows actual fluid temperature in
hose near FTS.
This equipment is used with heated fluid, which can
cause equipment surfaces to become very hot. To
avoid severe burns:
•
•
Do not touch hot fluid or equipment.
Allow equipment to cool completely before touch-
ing it.
Wear gloves if fluid temperature exceeds 110°F
(43°C).
Thermal expansion can cause overpressurization,
resulting in equipment rupture and serious injury,
including fluid injection. Do not pressurize system
when preheating hose.
a. Turn main power ON
.
g. Turn on
ing
and
heat zones by press-
A
B
°F
°C
b. Press
scale.
or
to change temperature
for each zone.
c. Press
.
h. Hold
zone.
to view electrical currents for each
d. To set
press
heat zone target temperature,
A
i. Hold
to view heater control circuit board
or
until display shows
temperature.
313539F
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Startup
j. Manual current control mode only:
4. Set pressure
When in manual current control mode, monitor hose
temperature with thermometer. Install per instructions
below. Thermometer reading must not exceed 160°F
(71°C). Never leave machine unattended when in
manual current control mode.
ON / OFF
If FTS is disconnected or display shows diag-
nostic code E04, turn main power switch OFF
PARK
PSI
then ON
to clear diagnostic
BAR
code and enter manual current control mode.
display will show current to hose. Current
is not limited by target temperature.
To prevent overheating, install hose thermome-
ter close to gun end, within operator view. Insert
thermometer through foam cover of A compo-
nent hose so stem is next to inner tube. Ther-
mometer reading will be about 20°F less than
actual fluid temperature.
a. Press
to display the pressure reading.
b. Press motor
. Motor and pumps start.
If thermometer reading exceeds 160°F (71°C),
Display shows system pressure.
reduce current with
key.
NOTE:
Motor must rotate counterclockwise when viewed from
c. Adjust hydraulic pressure control until display
shows desired fluid pressure.
+
-
ti7731a
ti7732a
NOTICE
Never adjust hydraulic pressure while spraying. This
will result in over pressure alarm E23.
NOTE:
If display pressure is greater than desired pressure,
reduce the hydraulic pressure and trigger gun to reduce
pressure.
26
313539F
Download from Www.Somanuals.com. All Manuals Search And Download.
Startup
NOTE:
Table 4: Available Pressure Imbalance Settings
Check the pressure of each proportioning pump using
the component A and B gauges. The pressures should
be approximately equal and must remain fixed.
PSI
BAR
PSI
BAR
100
200
300
400
*500
7
600
700
800
900
999
42
49
56
63
69
14
21
28
*35
d. To display cycle count, press
.
NOTE:
To clear counter, press and hold
* Factory default setting.
for 3 sec.
d. Turn main power switch OFF
changes.
to save
PSI
BAR
e. Press
scale.
or
to change pressure
5. Change pressure imbalance setting (optional)
The pressure imbalance function (status code 24, page
such as loss of feed pressure/supply, pump seal failure,
clogged fluid inlet filter, or a fluid leak.
NOTE:
Code 24 (pressure imbalance) is set to an alarm as the
default. To change to a warning, see H-VR Repair-Parts
manual 313540.
The pressure imbalance default is factory-set at 500 psi
(3.5 MPa, 35 bar). For tighter ratio error detection, select
a lower value. For looser detection or to avoid nuisance
alarms, select a higher value.
a. Turn main power switch OFF
.
PSI
BAR
b. Press and hold
power switch ON
or
, then turn main
. Display will read
dP500 for psi or dP_35 for bar.
c. Press
or
to select desired pres-
sure differential (100-999 in increments of 100
psi, or 7-70 in increments of 7 bar). See TABLE
4.
313539F
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Spraying
Spraying
4. Set PRESSURE RELIEF/SPRAY valves (SA, SB) to
SPRAY
SA
.
1. Engage gun piston safety lock.
SB
ti9877a
ti2409a
5. Check that heat zones are on and temperatures are
2. Close gun fluid manifold valves A and B.
6. Press motor
to start motor and pumps.
7. Check fluid pressure display while the gun is detrig-
8. Check fluid pressure gauges (GA, GB) to ensure
proper pressure balance. If imbalanced, reduce
pressure of higher component by slightly turning
PRESSURE RELIEF/SPRAY valve for that compo-
nent toward PRESSURE RELIEF/CIRCULATION
ti2728a
3. Attach gun fluid manifold. Connect gun air line.
Open air line valve.
, until gauges show balanced pressures.
GA
GB
In this example, B side
pressure is higher, so
use the B side valve to
balance pressures.
ti9877a
ti2543a
28
313539F
Download from Www.Somanuals.com. All Manuals Search And Download.
Spraying
9. Open gun fluid manifold valves A and B.
ti2414a
NOTE:
On impingement guns, never open fluid manifold valves
or trigger gun if pressures are imbalanced.
10. Disengage gun piston safety lock.
ti2410a
11. Test spray onto cardboard. Adjust pressure and
temperature to get desired results.
12. Equipment is ready to spray.
NOTE:
If you stop spraying for a period of time, the unit will
313539F
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby
Standby
Shutdown
If you stop spraying for a period of time, the unit will
enter standby by shutting down the electric motor and
hydraulic pump, to reduce equipment wear and mini-
mize heat buildup. The ON/OFF LED and the pres-
sure/cycle display on the motor control panel will flash
when in standby.
1. Shut off
,
, and
heat zones.
A
B
2. Park pumps.
a. Press
.
NOTE:
b. Trigger gun until pump A stops in the retracted
position and the pressure of both pumps bleeds
down.
The
,
, and
heat zones will not be
A
B
shut off in standby.
To restart, spray off target for 2 sec. The system will
sense the pressure drop and the motor will ramp up to
full speed in a few seconds.
3. Turn main power OFF
.
NOTE:
4. Close both fluid supply valves (FV).
This feature is disabled from the factory.
To activate or disable standby, adjust DIP switch #3 on
the motor control board. See Reactor Repair-Parts man-
ual 313540.
The idle time before entering standby is user-settable as
follows:
FV
ti10971a
1. Turn main power switch OFF
.
2. Press and hold
, then turn main power switch
ON
.
3. Press
or
to select desired timer set-
ting (5-20, in 5 minute increments). This sets the
length of inactive time before the unit will enter
standby.
4. Turn main power switch OFF
changes.
to save
30
313539F
Download from Www.Somanuals.com. All Manuals Search And Download.
Pressure Relief Procedure
Pressure Relief Procedure
5. Engage gun piston safety lock.
1. Relieve pressure in gun and perform gun shutdown
procedure. See gun manual.
ti2409a
2. Close gun fluid manifold valves A and B.
6. Disconnect gun air line and remove gun fluid mani-
fold.
ti2421a
3. Shut off feed pumps and agitator, if used.
ti2554a
4. Turn PRESSURE RELIEF/SPRAY valves (SA, SB)
to PRESSURE RELIEF/CIRCULATION
. Route
fluid to waste containers or supply tanks. Ensure
gauges drop to 0.
SA
SB
ti9879a
313539F
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Fluid Circulation
Fluid Circulation
and heat zones by pressing
Circulation Through Reactor
.
A
B
Do not turn on
heat zone unless hoses are
Do not circulate fluid containing a blowing agent with-
out consulting with your material supplier regarding
fluid temperature limits.
already loaded with fluid.
6. Press
to display actual temperatures.
To circulate through gun manifold and preheat hose, see
7. Before starting motor, reduce hydraulic pressure to
the minimum required to circulate fluid until
A
and
temperatures reach targets.
B
Do not install shutoffs downstream of the PRESSURE
RELIEF/SPRAY valve outlets (BA, BB). The valves
function as overpressure relief valves when set to
-
SPRAY
. Lines must be open so valves can
ti7732a
automatically relieve pressure when machine is oper-
ating.
8. Press motor
to start motor and pumps. Cir-
Route circulation lines back to respective compo-
nent A or B supply drum. Use hoses rated at the
maximum working pressure of this equipment. See
culate fluid at lowest possible pressure until temper-
atures reach targets.
9. Turn on
10. Set PRESSURE RELIEF/SPRAY valves (SA, SB) to
SPRAY
heat zone by pressing
.
3. Set PRESSURE RELIEF/SPRAY valves (SA, SB) to
PRESSURE RELIEF/CIRCULATION
.
.
SA
SA
SB
SB
ti9879a
ti9877a
4. Turn main power ON
.
32
313539F
Download from Www.Somanuals.com. All Manuals Search And Download.
Fluid Circulation
7. Before starting motor, reduce hydraulic pressure to
Circulation Through Gun
Manifold
the minimum required to circulate fluid until
A
and
temperatures reach targets.
B
Do not circulate fluid containing a blowing agent with-
out consulting with your material supplier regarding
fluid temperature limits.
-
ti7732a
Circulating fluid through the gun manifold allows rapid
preheating of hose.
1. Install gun fluid manifold (P) on Part 246362 acces-
sory circulation kit (CK). Connect high pressure cir-
culation lines (R) to circulation manifold.
8. Press motor
to start motor and pumps. Cir-
culate fluid at lowest possible pressure until temper-
atures reach targets.
P
CK
R
ti2767a
2. Route circulation lines back to respective compo-
nent A or B supply drum. Use hoses rated at the
maximum working pressure of this equipment. See
4. Turn main power ON
.
,
.
, and
heat zones by pressing
A
B
6. Press
to display actual temperatures.
313539F
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostic Codes
Diagnostic Codes
Temperature Control Diagnostic Codes
Temperature control diagnostic codes appear on tem-
perature display.
These alarms turn off heat. E99 clears automatically
when communication is regained. Codes E03 through
E06 can be cleared by pressing
. For other codes,
turn main power OFF
See repair manual for corrective action.
then ON to clear.
Code
01
Code Name
Alarm Zone
High fluid temperature
High current
Individual
Individual
Individual
Individual
Individual
Individual
02
03
04
05
06
30
No current
FTS not connected
Board overtemperature
Loss of zone communication
Momentary loss of communica- All
tion
99
Loss of display communication All
NOTE:
For hose zone only, if FTS is disconnected at startup,
display will show hose current 0A.
34
313539F
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostic Codes
Motor Control Diagnostic Codes
Motor control diagnostic codes E21 through E27 appear
on pressure display.
Warnings
Reactor will continue to run. Press
to clear. A
There are two types of motor control codes: alarms and
warnings. Alarms take priority over warnings.
warning will not recur for a predetermined amount of
time (varies for different warnings), or until main power
See repair manual for corrective action.
is turned OFF
then ON
.
Alarms
Alarms turn off Reactor. Turn main power OFF
Code
No.
Alarm or
Warning
Code Name
21
22
23
24
No transducer (component A) Alarm
No transducer (component B) Alarm
then ON
to clear.
High pressure
Alarm
NOTE:
Pressure imbalance
Selectable;
see repair
manual
Alarms can also be cleared, except for code 23, by
pressing
.
27
30
High motor temperature
Alarm
Momentary loss of communi- Alarm
cation
NOTE:
Code 24 (pressure imbalance) is set to an alarm default
of 500 psi (3.5 MPa, 35 bar). To change to a warning,
see Reactor Repair-Parts manual 313540. To change
the default pressure imbalance setting, see page 27.
31
99
Pumpline switch failure/high
cycle rate
Alarm
Loss of communication
Alarm
313539F
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Maintenance
•
Inspect hydraulic and fluid lines for leaks daily.
•
•
•
•
Keep component A from exposure to moisture in
atmosphere, to prevent crystallization.
•
Clean up all hydraulic leaks; identify and repair
cause of leak.
Clean gun mix chamber ports regularly. See gun
manual.
•
•
Inspect fluid inlet strainer screens daily, see below.
Clean gun check valve screens regularly. See gun
manual.
Grease circulation valves weekly with Fusion grease
(117773).
Use compressed air to prevent dust buildup on con-
trol boards, fan, motor (under shield), and hydraulic
oil coolers.
•
Keep vent holes on bottom of electrical cabinet
open.
ti9879a
•
Check hydraulic fluid level weekly. Check hydraulic
fluid level on dipstick (DS). Fluid level must be
between indent marks (IM) on dipstick. Refill as
required with approved hydraulic fluid; see Techni-
(AW) Hydraulic Oils table in the Reactor
Repair-Parts manual 313540. If fluid is dark in color,
change fluid and filter.
DS
IM
ti10003a
ti7861a
•
Change break-in oil in a new unit after first 250
hours of operation or within 3 months, whichever
comes first. See Table 4 for recommended fre-
quency of oil changes
Table 5: Frequency of Oil Changes
Ambient
Temperature
Recommended
Frequency
0 to 90°F
(-17 to 32°C)
1000 hours or 12 months,
whichever comes first
90°F and above
(32°C and above)
500 hours or 6 months,
whichever comes first
36
313539F
Download from Www.Somanuals.com. All Manuals Search And Download.
Fluid Inlet Strainer Screen
Fluid Inlet Strainer Screen
4. Ensure the pipe plug (59k) is screwed into the
strainer plug (59j). Install the strainer plug with the
screen (59g) and gasket (59h) in place and tighten.
Do not overtighten. Let the gasket make the seal.
The inlet strainers filter out particles that can plug the
pump inlet check valves. Inspect the screens daily as
part of the startup routine, and clean as required.
5. Open the fluid inlet valve, ensure that there are no
leaks, and wipe the equipment clean. Proceed with
operation.
Use clean chemicals and follow proper storage, transfer,
and operating procedures, to minimize contamination of
the A-side screen.
59g*
59d
59h
59j
NOTE:
Clean the A-side screen only during daily startup. This
minimizes moisture contamination by immediately flush-
ing out any isocyanate residue at the start of dispensing
operations.
59k
ti9886a
FIG. 11: Fluid Inlet Strainer
1. Close the fluid inlet valve at the pump inlet and shut
off the appropriate feed pump. This prevents mate-
rial from being pumped while cleaning the screen.
* See Reactor Repair-Parts manual 313540 for fluid filter
screen replacements.
2. Place a container under the strainer manifold (59d)
to catch fluid. Remove the strainer plug (59j).
3. Remove the screen (59g) from the strainer manifold.
Thoroughly flush the screen with compatible solvent
and shake it dry. Inspect the screen. If more than
25% of the mesh is blocked, replace the screen.
Inspect the gasket (59h) and replace as required.
313539F
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Flushing
Flushing
Flush equipment only in a well-ventilated area. Do not
spray flammable fluids. Do not turn on heaters while
flushing with flammable solvents.
•
Flush out old fluid with new fluid, or flush out old
fluid with a compatible solvent before introducing
new fluid.
•
•
Use the lowest possible pressure when flushing.
All fluid components are compatible with common
solvents. Use only moisture-free solvents.
•
To flush feed hoses, pumps, and heaters separately
from heated hoses, set PRESSURE
RELIEF/SPRAY valves (SA, SB) to PRESSURE
RELIEF/CIRCULATION
lines (N).
. Flush through bleed
SB
SA
N
N
ti9880a
•
•
To flush entire system, circulate through gun fluid
manifold (with manifold removed from gun).
To prevent moisture from reacting with isocyanate,
always leave the system dry or filled with a mois-
ture-free plasticizer or oil. Do not use water. See
38
313539F
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Dimensions
Dimension
D (front and rear mounting holes) 32.5 (825.5)
F (side mounting holes) 30.375 (7715)
in. (mm)
Dimension
A (height)
B (width)
in. (mm)
57.31 (1455.42)
37.86 (961.6)
33 (838.2)
G (mounting post inner diameter) 0.44 (11)
C (depth)
Top View
G
D
Front of Machine
A
C
F
Rear of Machine
r_256886_313359_1A
D
B
313539F
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Technical Data
Category
Data
Maximum Fluid Working Pressure 3500 psi (24.1 MPa, 241 bar)
Fluid Inlets
3/4 npsm union in 1 in. npt(f) ball valve
Fluid Outlets
Component A (ISO): #8 (1/2 in.) JIC, with #5 (5/16 in.) JIC adapter
Component B (RES): #10 (5/8 in.) JIC, with #6 (3/8 in.) JIC adapter
1/4 npsm(m), with plastic tubing, 250 psi (1.75 MPa, 17.5 bar) maximum
190°F (88°C)
Fluid Circulation Ports
Maximum Fluid Temperature
Maximum Output (10 weight oil at Model H-VR: 3.0 gpm (11.4 liter/min) (60 Hz)
ambient temperature) 1:1
Output per Cycle
Variable: 2 oz.- 5 oz. (60 cc - 150 cc) per pump*
Variable: 2 in. - 5 in. (5.08 cm - 12.7 cm)
230V 3 phase units: 195-264 Vac, 50/60 Hz
400V 3 phase units: 338-457 Vac, 50/60 Hz
Stroke Length
Line Voltage Requirement
Amperage Requirement
Heater Power
(A and B heaters total, no hose)
Hydraulic reservoir capacity
Recommended hydraulic fluid
Sound power, per ISO 9614-2
3.5 gal. (13.6 liters)
Citgo A/W Hydraulic Oil, ISO Grade 46
90.9 dB(A)
Sound pressure,
84.0 dB(A)
1 m from equipment
Weight
955 lb (433 kg)
Wetted Parts
Aluminum, stainless steel, zinc-plated carbon steel, brass, carbide, chrome,
fluoroelastomer, PTFE, ultra-high molecular weight polyethylene, chemically
resistant o-rings
*Output example: 2.5:1 ratio = 150 cc (B side):60 cc (A side)
2.5:1 output = 150 cc (B side) + 60 cc (A side) = 210 cc per cycle
All other brand names or marks are used for identification purposes and are trademarks of their respective owners.
40
313539F
Download from Www.Somanuals.com. All Manuals Search And Download.
Performance Charts
Performance Charts
Foam Performance Chart
2000
(13.8, 138)
KEY
A = H-25 at 50 Hz
B = H-25 at 60 Hz
C = H-40 at 50 Hz
D = H-40 at 60 Hz
E = H-50 at 50 Hz
❄F = H-50 at 60 Hz
G = H-VR at 60 Hz
A
1500
(10.3, 103)
B
G
1000
(6.9, 69)
C
E
500
(3.4, 34)
D
F
45
(20.5)
0
55
(25.0)
35
(15.9)
25
(11.4)
5
(2.3)
15
(6.8)
Flow Rate in lb/min (kg/min)
❄ Pressure flow curve for model 253725 (H-50 230V 1 phase) not shown.
Maximum pressure limited to 1700 psi (11.7 MPa, 11.7 bar)
Coatings Performance Chart
3500
(24.1, 241)
KEY
H = H-XP2 at 50 Hz
J = H-XP2 at 60 Hz
K = H-XP3 at 50 Hz
L = H-XP3 at 60 Hz
M = H-VR at 60 Hz
3000
(20.7, 207)
H
2500
(17.2, 172)
J
K
2000
(13.8, 138)
M
1500
(10.3, 103)
L
1000
(6.9, 69)
500
(3.4, 34)
2.0
2.5
3.0
0
1.0
(3.8)
1.5
(5.7)
0.5
(1.9)
(7.6) (9.5) (11.4)
Flow Rate in gal/min (liter/min)
313539F
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Performance Charts
Heater Performance Chart
140
(78)
130
(72)
120
(67)
110
(61)
100
(56)
90
KEY
H-VR = 15.3 kW
H-VR
(50)
80
(44)
70
(39)
60
(33)
50
(28)
40
(22)
30
(17)
20
(11)
10
(6)
0
2.0
(7.6)
2.5
(9.5)
3.0
(11.4)
4.5
(17.0)
1.0
(3.8)
1.5
(5.7)
3.5
(13.2)
4.0
(15.1)
0.5
(1.9)
Flow Rate in gpm (lpm)
★ Heater performance data is based on testing with 10 wt.
hydraulic oil and 230V across heater power wires.
42
313539F
Download from Www.Somanuals.com. All Manuals Search And Download.
Performance Charts
313539F
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 313539
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Copyright 2009, Graco Inc. is registered to ISO 9001
Revised 08/2010
Download from Www.Somanuals.com. All Manuals Search And Download.
|