BELT SANDER - 1 X 30 INCHES
Model 02485
AsseMbly And OperAtiOn instructiOns
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
tO preVent seriOus injury, reAd And understAnd
All wArnings And instructiOns befOre use.
Copyright© 2002, 2007 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form without
the express written consent of Harbor Freight Tools.
for technical questions or replacement parts, please call 1-800-444-3353.
Manual revised 01/07
Download from Www.Somanuals.com. All Manuals Search And Download.
or modify the plug in any way. do not use any adapter plugs. check with a quali-
fied electrician if you are in doubt as to whether the outlet is properly grounded.
If the tools should electrically malfunction or break down, grounding provides a low
resistance path to carry electricity away from the user.
2.
double insulated tools are equipped with a polarized plug (one blade is wider
than the other). this plug will fit in a polarized outlet only one way. if the plug
does not fit fully in the outlet, reverse the plug. if it still does not fit, contact a
qualified electrician to install a polarized outlet. do not change the plug in any
way. Double insulation eliminates the need for the three wire grounded power cord
and grounded power supply system.
3.
4.
5.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and
refrigerators. There is an increased risk of electric shock if your body is grounded.
do not expose power tools to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock.
do not abuse the power cord. never use the power cord to carry the tools or pull
the plug from an outlet. keep the power cord away from heat, oil, sharp edges,
or moving parts. replace damaged power cords immediately. Damaged Power
Cords increase the risk of electric shock.
6.
1.
when operating a power tool outside, use an outdoor extension cord marked
“w-A” or “w”. These extension cords are rated for outdoor use, and reduce the risk
of electric shock.
persOnAl sAfety
stay alert. watch what you are doing, and use common sense when operating a
power tool. do not use a power tool while tired or under the influence of drugs,
alcohol, or medication. A moment of inattention while operating power tools may
result in serious personal injury.
2.
3.
4.
dress properly. do not wear loose clothing or jewelry. contain long hair. keep
your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or
long hair can be caught in moving parts.
Avoid accidental starting. be sure the power switch is off before plugging in.
Carrying power tools with your finger on the Power Switch, or plugging in power tools
with the Power Switch on, invites accidents.
remove adjusting keys or wrenches before turning the power tool on. A wrench
or a key that is left attached to a rotating part of the power tool may result in personal
injury.
5.
6.
do not overreach. keep proper footing and balance at all times. Proper footing
and balance enables better control of the power tool in unexpected situations.
use safety equipment. Always wear eye protection. Dust mask, nonskid safety
shoes, hard hat, or hearing protection must be used for appropriate conditions. Always
SKU 02485
for technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
wear ANSI-approved safety goggles and a dust mask/respirator when using or perform-
ing maintenance on this tool.
tOOl use And cAre
1.
2.
use clamps (not included) or other practical ways to secure and support the
workpiece to a stable platform. Holding the work by hand or against your body is
unstable and may lead to loss of control.
do not force the tool. use the correct tool for your application. The correct tool
will do the job better and safer at the rate for which it is designed. Do not force the tool
and do not use the tool for a purpose for which it is not intended.
3.
4.
do not use the power tool if the power switch does not turn it on or off. Any tool
that cannot be controlled with the Power Switch is dangerous and must be replaced.
disconnect the power cord plug from the power source before making any ad-
justments, changing accessories, or storing the tool. Such preventive safety mea-
sures reduce the risk of starting the tool accidentally. Always unplug the tool from
its electrical outlet before performing any inspection, maintenance, or cleaning
procedures.
5.
6.
store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users.
Maintain tools with care. keep cutting tools sharp and clean. Properly maintained
tools with a sharp cutting edge are less likely to bind and are easier to control. Do not
use a damaged tool. Tag damaged tools “Do not use” until repaired.
7.
8.
check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool’s operation. if damaged, have the tool
serviced before using. Many accidents are caused by poorly maintained tools.
use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
serVice
1.
2.
tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel could result in a risk of injury.
when servicing a tool, use only identical replacement parts. follow instructions
in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of
unauthorized parts or failure to follow maintenance instructions may create a risk of
electric shock or injury.
specific sAfety rules
1.
support workpiece with worktable.
SKU 02485
for technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
3.
Maintain 1/16” maximum clearance between table and sanding belt or disc.
Avoid kickback by sanding in accordance with the direction arrows. Sanding belt
is designed to rotate down towards the table.
4.
5.
Maintain labels and nameplates on the tool. These carry important information. If
unreadable or missing, contact Harbor Freight Tools for a replacement.
Avoid unintentional starting. Make sure you are prepared to begin work before turn-
ing on the tool.
6.
7.
Always keep the extension cord away from moving parts on the tool.
people with pacemakers should consult their physician(s) before using this
product. Electromagnetic fields in close proximity to a heart pacemaker could cause
interference to or failure of the pacemaker. In addition, people with pacemakers should
adhere to the following:
• Avoid operating power tools alone.
• Don’t use a power tool with the power switch locked on.
• If powered via a power cord be certain that the tool is properly grounded. A ground
fault interrupt (GFCI) system is also a good precaution. This inexpensive device is a
good safety measure because it prevents a sustained electrical shock.
• Properly maintain and inspect all tools before use to avoid electrical shock.
8.
never leave the tool unattended when it is plugged into an electrical outlet. Turn
off the tool, and unplug it from its electrical outlet before leaving. Do not leave tool until
it comes to a complete stop.
9.
never run the belt sander without the spark cover properly installed.
10.
take caution as some woods contain preservatives such as copper chromium
arsenate (ccA) which can be toxic. When sanding these materials extra care should
be taken to avoid inhalation and minimize skin contact.
11.
wArning: some dust created by power sanding, sawing, grinding, drilling, and
other construction activities, contains chemicals known [to the state of califor-
nia] to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
Lead from lead-based paints
Crystalline silica from bricks and cement or other masonry products
Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust masks that are specially de-
signed to filter out microscopic particles. (California Health & Safety Code § 25249.5,
et seq.)
warning: The warnings, cautions, and instructions discussed in this instruction manual can-
not cover all possible conditions and situations that may occur. It must be understood
by the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
SKU 02485
for technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
grOunding
wArning!
improperly connecting the grounding wire can result in the risk of electric shock.
check with a qualified electrician if you are in doubt as to whether the outlet is
properly grounded. do not modify the power cord plug provided with the tool.
never remove the grounding prong from the plug. do not use the tool if the
power cord or plug is damaged. if damaged, have it repaired by a service facil-
ity before use. if the plug will not fit the outlet, have a proper outlet installed by
a qualified electrician.
grOunded tOOls:tOOls witH tHree prOng plugs
1.
Tools marked with“Grounding Required”have a three wire cord and three prong ground-
ing plug. The plug must be connected to a properly grounded outlet. If the tool should
electrically malfunction or break down, grounding provides a low resistance path to
carry electricity away from the user, reducing the risk of electric shock. (see 3-prong
plug and Outlet.)
2.
3.
The grounding prong in the plug is connected through the green wire inside the cord
to the grounding system in the tool. The green wire in the cord must be the only wire
connected to the tool’s grounding system and must never be attached to an electrically
“live” terminal. (see 3-prong plug and Outlet.)
Your tool must be plugged into an appropriate outlet, properly installed and grounded in
accordance with all codes and ordinances. The plug and outlet should look like those
in the following illustration. (see 3-prong plug and Outlet.)
3-prong plug and Outlet
Outlets for 2-prong plug
dOuble insulAted tOOls:tOOls witH twO prOng plugs
1.
Tools marked “Double Insulated” do not require grounding. They have a special double
insulation system which satisfies OSHA requirements and complies with the applicable
standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and
the National Electrical Code. (see Outlets for 2-prong plug.)
SKU 02485
for technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
Double insulated tools may be used in either of the 120 volt outlets shown in the pre-
ceding illustration. (see Outlets for 2-prong plug.)
extensiOn cOrds
1.
2.
Grounded tools require a three wire extension cord. Double Insulated tools can use
either a two or three wire extension cord.
As the distance from the supply outlet increases, you must use a heavier gauge exten-
sion cord. Using extension cords with inadequately sized wire causes a serious drop
in voltage, resulting in loss of power and possible tool damage.
(see table A.)
3.
The smaller the gauge number of the wire, the greater the capacity of the cord. For
example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
(see table A.)
4.
5.
When using more than one extension cord to make up the total length, make sure each
cord contains at least the minimum wire size required. (see table A.)
If you are using one extension cord for more than one tool, add the nameplate amperes
and use the sum to determine the required minimum cord size.
(see table A.)
6.
7.
If you are using an extension cord outdoors, make sure it is marked with the suffix “W-
A” (“W” in Canada) to indicate it is acceptable for outdoor use.
Make sure your extension cord is properly wired and in good electrical condition. Al-
ways replace a damaged extension cord or have it repaired by a qualified electrician
before using it.
8.
Protect your extension cords from sharp objects, excessive heat, and damp or wet
areas.
recOMMended MiniMuM wire gAuge fOr extensiOn cOrds*
(120 Or 240 VOlt)
nAMeplAte
AMperes
(at full load)
extensiOn cOrd lengtH
25 feet
50 feet
75 feet 100 feet 150 feet
0 – 2.0
2.1 – 3.4
18
18
18
18
18
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
3.5 – 5.0
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
-
-
-
* based on limiting the line voltage drop to five volts at 150% of the rated amperes.
tAble A
SKU 02485
for technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
syMbOlOgy
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
Volts Alternating Current
V~
A
Amperes
No Load Revolutions per Minute (RPM)
n xxxx/min.
0
note: Performance of this tool may vary depending on variations in local line voltage. Exten-
sion cord usage may also affect tool performance.
unpAcking
When unpacking, check to make sure the following parts are included. Refer to the
Assembly Drawing and Parts List located at the end of this manual. If any parts are missing
or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon
as possible.
SKU 02485
for technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
AsseMbly
The Belt Sander requires minor assembly of theTable (29) to the Main Body (23). Refer
to the Parts List and Assembly Drawing at the end of this manual.
Sanding Belt
Tension Handle (37)
Tracking Knob (1
Cover Knob (16)
Side Cover (10)
Back Pulley (14)
1.
2.
Remove Cover Knob (16) and take off the Side Cover (10). See illustration above.
Remove the Screw (9) and Toothed Washer (24) from the end of the Locking Stud
(25).
3.
4.
5.
Place the Table (29) on the Main Body (23) so that the Sanding Belt (5) fits through
the Slot in the Table.
Attach the Table by placing the Handle Assembly on the Table side and securing the
entire assembly using Screw (9).
Replace the Side Cover.
Sanding Belt (5)
Table Slot
Frame (23)
Main Body (
Spark Cover (43)
Spark Shield (43)
Screw (9)
(Under Table)
Screw (44)
Table (29)
Main Body (23)
Toothed Washer (24)
Table Lock Handle Assembly (24-28)
6.
Loosen the Screw (44) most of the way as shown above.
SKU 02485
for technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
Place the Spark Shield (43) on the Belt Sander Unit and secure using the Screw
(44).
8.
Place the Belt Sander on a secure workbench able to carry the weight of the Belt
Sander and stock.
9.
Attach the vacuum hose (if used) to the 1-3/4 inch vacuum chute.
Otherwise, attach a vacuum bag (not supplied) to collect the sanding dust.
10.
For added safety and reduced vibration, it is recommended that the Belt Sander be
mounted to the workbench with “C” clamps or other appropriate devices.
OperAtiOn
note: The Belt Sander is designed to sand only workpieces made of wood.
sanding
1.
2.
3.
Plug Sander into wall socket (or extension cord) containing grounding prong.
Place your safety glasses and full face shield on.
Turn on power Switch (19) momentarily to verify that Sander Belt (5) is tracking prop-
erly. If belt tracking needs adjustment, turn Belt Sander off and refer to instructions
on page 7.
4.
If the Sanding Belt (5) is rotating properly with proper tracking, the Belt Sander is ready
for use.
5.
6.
Turn on power Switch (19).
Begin sanding.
caution: do not apply so much pressure on object being sanded to stop rotation
of sanding belt. keep fingers away from the sanding belt.
SKU 02485
for technical questions, please call 1-800-444-3353.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting table Angle
1.
2.
3.
Loosen the Table Adjustment Locking Handle (26) by turning it counterclockwise as
shown above.
Tilt the Table (29) to the desired angle: Use a protractor to ensure accuracy. There
should be no more than 1/16” between the Table and the Sanding Belt (5).
Tighten the Table Adjustment Handle.
leveling the table
1.
Using a protractor, verify that the Table is 90° to the belt. If it is not, continue with the
following steps.
2.
3.
If the Table is tilted toward the front of the machine, tighten the Set Screw (30).
If the Table is tilted toward the back of the machine, loosen the Set Screw.
removing and installing sanding belt
Sanding Belt
Tension Handle (37)
Tracking Knob (1
Cover Knob (16)
(Also use for belt
tracking adjustments)
Side Cover (10)
Back Pulley (14)
1.
2.
Remove the Cover Knob (16), then remove the Side Cover (#10) as shown above.
Turn the Tension Handle (37) counterclockwise to loosen the Sanding Belt (5).
SKU 02485
for technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
4.
Remove the Sanding Belt.
Place the new Sanding Belt on the three pulleys. Center the Sanding Belt on the pul-
leys.
5.
6.
Tighten the Sanding Belt by turning the Tension Handle clockwise until the Back Pul-
ley (14) appears centered. Belt tracking adjustments are made by slightly turning this
knob as needed. See above.
Replace the Side Cover and Cover Knob.
Adjusting the sanding belt tracking
1.
2.
Turn the Belt Sander on.
Look at the Belt (5) through the back of the Spark Cover (43). If it is riding on the center
of the upper Pulley (14) the tracking is correct and no further adjustment is required.
3.
4.
If the Belt rides to the left, turn the Tension Handle (37) to the left until the Belt is cen-
tered.
If the Belt rides to the right, turn the Tension Handle gradually to the right until the Belt
is centered.
Adjustment of belt support
The Belt Support (20) is made of heavy gauge steel to support or back the Sanding
Belt while sanding. It should be adjusted to no more than 1/16” away from the back of the
Sanding Belt.
caution: Do not sand stock that is too small to be safely supported or held. Such pieces
should be sanded by hand.
1.
2.
3.
Remove the Table (29) by removing the Screw (9) as shown below.
Loosen the two Bolts (22) on the Belt Support (20).
Adjust the Belt Support to no more than 1/16” away from the back of the Sanding
Belt.
4.
Tighten the two Bolts on the Belt Support.
SKU 02485
for technical questions, please call 1-800-444-3353.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Bolts (22)
Screw (9)
Table (29)
Belt Support (20)
Maintenance
1.
Keep Sander clean by blowing dust off with compressed air. Wear safety glasses and
dust mask or respirator while doing this.
2.
3.
4.
5.
Cover Sander when not in use.
Periodically, apply a light oil to the table to prevent rusting.
Store in a clean and dry location.
Replace Sanding Belts when they become torn or worn down to the paper.
SKU 02485
for technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
pArts list
part
description
Rubber Feet
Q’ty
4
part
23 Main Body
description
Q’ty
1
1
2
3
4
5
6
7
8
9
Bolt, M8 x 20
Spring Washer, F 8
Base
2
24 Toothed Washer, F 8
25 Locking Stud
26 Locking Handle
27 Spring
1
2
1
1
1
Sanding Belt
Motor Pulley
Set Screw, M6x10
Bolt, M8x25
1
1
1
28 Screw
1
1
29 Table
1
1
30 Set Screw, M6x16
31 Motor
1
Screw, M6x12
1
1
10 Side Cover
1
32 Set Screw, M6x8
33 Tension Axle
34 Axle Seat
1
11 Nut, M10
1
1
12 Washer, F10
13 C- Ring, 15
14 Pulley
2
1
2
35 Spring Pin, F 3
36 Spring
1
2
1
15 Bearing, 6202
16 Tracking Knob
17 Pulley Axle
18 Power Cord
19 Switch
2
37 Tension Handle
38 Spring
1
1
1
1
39 Washer, F 5
40 Lock E-Ring
41 Spring
1
1
1
1
1
20 Belt Support
21 Washer, F 4
22 Bolt, M4x10
1
42 Bolt, M10x30
43 Spark Cover
44 Screw, M4x10
1
2
1
2
1
pleAse reAd tHe fOllOwing cArefully
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEM-
BLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER
OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER
THAT HE OR SHE IS qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR
SHE IS qUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR ExPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS
TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
record product’s serial number Here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts.
SKU 02485
for technical questions, please call 1-800-444-3353.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
AsseMbly diAgrAM
SKU 02485
for technical questions, please call 1-800-444-3353.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
wiring diAgrAM
GROUND TO MOTOR
NEUTRAL
HOT
RED
OFF
MOTOR
SWITCH
ON
BLACK
Capacitor
124 µF 5%
250 V~
Capacitor is not Polarity - Specific
LIMIteD 90 DAy/1yeAr wArrAnty
Harbor FreightTools Co.makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser for a period of ninety days from date of purchase that the motor/engine, the
belts (if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship. Harbor
Freight Tools also warrants to the original purchaser, for a period of one year from date of purchase, that all other
parts and components of the product are free from defects in materials and workmanship.This warranty does not
apply to damage due directly or indirectly to misuse, abuse, negligence or accidents;repairs or alterations outside
our facilities; or to lack of maintenance.We shall in no event be liable for death, injuries to persons or property, or
for incidental, contingent, special or consequential damages arising from the use of our product. Some states do
not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion
may not apply to you. THiS WarranTy iS expreSSly in lieu oF all oTHer WarranTieS, expreSS
or implied, inCluding THe WarranTieS oF merCHanTabiliTy and FiTneSS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid.
proof of purchase date and an explanation of the complaint must accompany the merchandise. if our inspection
verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our
expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of
our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 02485
for technical questions, please call 1-800-444-3353.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
|