MM-1000 Mixer
1 9 " 3 C H A N N E L S T E R E O M I X E R
PROFESSIONELLER 3-KANAL STEREO-MIXER
MEZCLADORESTEREODE3CANALESPROFESIONAL
MIXER STEREO 3 VOIES PROFESSIONNEL
OPERATIONS
MANUAL
BEDIENUNGSHANDBUCH
MANUAL DEL OPERADOR
MANUEL D’INSTRUCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
MM-1000
5
REAR PANEL
1
2
3
4
6
TOP PANEL
21
19
20
14
8
15
10
7
9
16
11
13
17
12
18
(3)
Download from Www.Somanuals.com. All Manuals Search And Download.
MM-1000
5
CONVERTIBLE PHONO/LINE INPUTS
INTRODUCTION
The MM-1000 has 2 CONVERTIBLE PHOH/LN) RCA
INPUTS These small switches which are located to the right of the
RCA inputs for channels 2 and 3 allow you to choose between a
PHONO (Turntable) input or a LINE level (Mp3, CD, Tape player
etc..).and require the proper switching.
Congratulations on your purchase of Gemini MM-1000 19” 3 channel
stereo mixer. This-state-of-the-art mixer features the latest technological
advances and is backed by a 1 year warranty, excluding the cross fader.
The cross fader is backed by a separate 90 day warranty.
Prior to use we suggest that you carefully read all the instructions.
When switched to the PH position you may use any Turntable with
a magnetic cartridge, remember to connect your ground wire (see
GROUNDING SCREW) or there may be a system hum
FEATURES
And when the switch is in the LN position you may connect any
- 19” 3 Stereo channel mixer
line level device as described before (Mp3, CD, Tape etc).
- 6 line, 2 convertible phono/line, RCA inputs
- Master & record RCA outputs
- Microphone Input
NOTE: CONNECTING A LINE LEVEL DEVICE TO A PH INPUT MAY
CAUSE THAT MIXER CHANNEL TO OVERLOAD AND OR DISTORT.
- 5 band graphic equalizer.
- Cue button switches for easy channel cue
- Rotary cue volume, CUE/PGM
- Dual VU display with mode switch
- Master fader with Mono/Stereo selector
Now you may plug the RCA’s from your playable medium into each
input to be connected to thier respective CHANNELS (CH).
6
Then when all of your connections have been made turn on the
mixer by pressing the POWER SWITCH.
PRECAUTIONS
MIC (MICROPHONE) INPUT
The MIC or Microphone input s loce top left hand corner
of the front of the MM-1000 and will accept any standard balanced
and unbalanced 1/4” connector. You can control the gain and even
set the low’s and the high’s for the mic (See CONTROLS ) below.
1. All instructions should be read before using this equipment.
2. To reduce the risk of electrical shock, do not open the unit.
Please refer all servicing needs to a Gemini-qualified service
technician.
8
HEADPHONE OUTPUT
The HEADPHONE OUTUT loche bottom right hand cor-
ner of the MM-1000 will accept any headphone with a standard
1/4” connector and or adaptor and will allow you to CUE your
music program before you play it, you can adjust the volume and
PGM mix of the HEADPHONE (see CONTROLS) below.
IN THE USA ~ IF YOU EXPERIENCE PROBLEMS WITH THIS UNIT CALL
GEMINI CUSTOMER SERVICE AT: 1 (732) 346-0061. DO NOT ATTEMPT TO
RETURN THIS EQUIPMENT TO YOUR DEALER.
3. Do not expose this unit to direct sunlight or a heat source
such as a radiator or stove.
4. This unit should be cleaned only with a damp cloth. Avoid sol-
vents or other cleaning detergents.
CONTROLS
MICROPHONE CONTROL
5. When moving this equipment it should be placed in its origi-
nal carton and packaging. This will reduce the risk of damage
during transit.
Under the microphone input jack are the microphone controls,
which consist of:
6. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
MICROPHONE VOLUME
Which allows you to adjust he he microphone signal.
7. DO NOT USE SPRAY CLEANERS OR LUBRICANTS ON
CONTROLS, SURFACES OR SWITCHES.
MICROPHONE EQ
Which allows you to rol thuency and the high fre-
quency of the microphone signal.
CONNECTIONS
0
CHANNEL INPUT SELECTOR
1
Ensure that the POWER SWITCH
The CHANNEL INPUT SELECTOR switches allow you to choose
which input will be controlled by that channels corresponding
volume FADER.
is in the OFF position prior to makctions.
POWER CORD
This unit comes h a POWER Cg in to the rear panel
POWER CORD socket before plugging it in to a proper power source.
For example on CHANNEL (1) the INPUT SELECTOR allows you
to choose between LINE 1 in or LINE 2 in, and on CHANNEL (2)
The INPUT SELECTOR allows you to choose between PHONO
1/LINE 3 and LINE 4 , and also on CHANNEL (3) the INPUT
SELECTOR SWITCH will let you choose between PHONO 2/LINE
5 and LINE 6. (see CONVERTIBLE LINE INPUT) for PHONO 1/
LINE 3 and PHONO 2/ LINE 5 switching.
The MM-1000 has 2 stereo outputs located on the rear panel:
The MASTER RCA OUTPUT
connects the mixer to your maampg standard audio cables
with RCA-type connectors.
CHANNEL VOLUME FADER
The RECORD RCA OUTPUT
After you have chosen which ut you with the INPUT
SELECTOR the corresponding CHANNEL FADER will allow you to
adjust the volume for that particular CHANNEL.
The RECORD output jacks can e usnnect the mixer to the
record input of your recording unit, thus enabling you to record your
mix with RCA cables.
2
CROSS FADER
GROUNDING SCREW
The CROSS FADER allows yoevenly from one source to
another. On the MM-1000 The CROSS FADER controls the mix
between CHANNEL 2 and CHANNEL 3. The CROSS FADER on
the MM-1000 is removable and if the need arises can be
replaced.The RG-45 (RAILGLIDE™) DUAL-RAIL CROSS
FADER, which has internal dual stainless steel rails that allow the
slider to ride smoothly and accurately from end to end can be pur-
chased from your local GEMINI dealer.
When using (a) turntableyou will ground the RCA cable(s)
by screwing in the grounding fork(s) to the GROUNDING SCREW
located on the rear panel of the MM-1000 mixer.
Attach a PHONO (Turntable) ground line to the silver GROUND
THUMB SCREW that is situated at the bottom middle of the rear
panel.
SEE REPLACEMENT INSTRUCTION ON THE NEXT PAGE.
(4)
Download from Www.Somanuals.com. All Manuals Search And Download.
MM-1000
“Ipod Friendly” Cable: To connect your Ipod or
other Digital Media Player, use the included Ipod
cable.
Connect the 1/8” end of the cable to the headphone
or line out jack of your player, and connect the RCA
to the line input of your mixer.
FADERREPLACEMENT
Befor replacing the FADER you must first remove the main faceplate of
the MM-1000. Start by removing all the FADER type knobs like the
CHANNEL fader the GRAPHIC EQ and of course the CROSSFADER
itself. after you have completed that, you must remove the six screws
located on the front of the faceplate.
then gently lift the plate to uncover the the old CROSS FADER.
SPECIFICATIONS
Then follow the next four steps to replace the actual fader.
INPUTS:
Phono.....................................................................................3mV,47 KOhm
Line..................................................................................150 mV, 27 KOhm
MIC......................................................................1.5 mV, 1 KOhm Balanced
1. UNSCREW THE FADER (B) SCREWS. DO NOT TOUCH
INSIDE SCREWS (C) CAREFULLY REMOVE OLD CROSS FADER
AND UNPLUG CABLE (D)
OUTPUTS:
2. PLUG IN THE NEW CROSS
FADER INTO CABLE (D) AND
PLACE BACK INTO MIXER.
Max...................................................................................20V Peak-to-Peak
Rec.....................................................................................225 mV, 5 KOhm
GENERAL:
3. SCREW THE CROSS FADER
TO MIXER WITH THE FADER
PLATE SCREWS (B)
Frequency Response.................................................20Hz - 20KHz +/- 2dB
Distortion..........................................................................................< 0.02%
S/N Ratio...........................................................................Better than 85 dB
Headphone impedance..................................................................16 Ohm
Power Source (external)......................................................AC 15V, 500mA
Unit Demensions.....................................................................19” x 3.3” x 7”
..........................................................................(482.6 x 83.82 x 177.8 mm)
Weight................................................................................6.35 lbs (2.88 kg)
4. REPLACE THE FACE OF THE
MIXER AND SCREW THE FOUR
SCREWS BACK IN AND REPLACE THE FADER KNOBS.
NOTE: WHEN USING THE CROSS FADER LIGHTLY GLIDE THE
FADER BACK AND FORTH. PRESSING DOWN ON THE CONTROLS
CAN BEND CONTACTS AND CAUSE A LOSS OF SOUND.
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTIFICATION FOR IMPROVEMENT
CONTROLSCONTINUED
3
MASTER FADER
The MASTER FADdjusts the f the main music program.
4
MONO/STEREO SWITCH
The MONO/ STEREO SWITallto set the main output to mono
which is a combination of both LEFT and RIGHT inputs .
And STEREO which is a standard LEFT pan RIGHT pan stereo setup.
5
CHANNEL CUE BUTTONS
The CHANNEL CUE BUTTOalo individually choose which
channel you wish to monitor in your headphones, you can monitor one at
a time or any combination of the three.
6
CUE/PGM ROTARY KNOB
The CUE/PGM ROTARY KNdethe mix between the chosen
CHANNEL CUE BUTTON(s) and the MAIN OUTPUT mix.
7
CUE VOLUME ROTARY KNOB
The CUE VOLUME ROTARY KNOB aur HEADPHONE MONI-
TOR OUTPUT’S volume.
8
HEADPHONE MONITOR OUTPUT
The HEADPHONE MONITOR OUTPUT wany standard 1/4”
connector and can be used for CUE MONITORING as described above.
9
5 BAND GRAPHIC EQUALIZER
The 5 BAND GRAPHIC EQUALIZadone of the MAIN OUT-
PUTS by giving you a choice 5 frequencies (BANDS) to adjust , from lows
60Hz and 400Hz to midrange 1KHz to highs 6KHz and 15KHz you can
use the adjustment sliders to higher or lower the 5 separate frequencies
till the sound of the MAIN OUTPUT’s is appropriate to your listening envi-
roment.
0
VU METER AND VU MODE SWITCH
The MM-1000 has a dual mode VU MTER ws you to monitor the
decible levels of the CUE and PGM or LEFT and RIGHT stereo levels of
the MASTER output. When the VU MODE SWITCH is set to CUE the VU
METER will display the CUE/PGM level or if set to MASTER the VU
METER will display the level of the MASTER output.
(5)
Download from Www.Somanuals.com. All Manuals Search And Download.
|