GE Appliances
Safety Information . . . . . . . . . . . .3
Owner’s Manual
Operating Instructions
Control Panel . . . . . . . . . . . . . . . . . .4
Control Settings . . . . . . . . . . . . . . . .5
Loading and Using
WNCD2050
the Washer . . . . . . . . . . . . . . . . . .7, 8
Washer Features . . . . . . . . . . . . . . . .6
Troubleshooting Tips . . . . . .9–12
Customer Service
Product Registration . . . . .2, 13, 14
Service Telephone
Numbers . . . . . . . . . . .2, Back Cover
Warranty . . . . . . . . . . . . . . . . . . . . .15
175D1807P323 49-90058 7-00 JR
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
SafeyIructions
For your safety, the information in this manual must be followed to minimize the risk of fire
WARNING!
or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
WATER HEATER SAFETY
Under certain conditions hydrogen gas may be produced in a water heater that has not been used for two weeks
or more. Hydrogen gas can be explosive under these circumstances.
If the hot water has not been used for two weeks or more, prevent the possibility of damage or injury by turning on
all hot water faucets and allowing them to run for several minutes. Do this before using any electrical appliance
which is connected to the hot water system. This simple procedure will allow any built-up hydrogen gas to escape.
Since the gas is flammable, do not smoke or use an open flame or appliance during this process.
PROPER INSTALLATION
If you did not receive an Installation Instructions sheet, visit our Website at: www.geappliances.com.
OpeagIructions
This washer must be properly installed and located in accordance with the Installation Instructions before it is used.
■ Install or store where it will not be exposed to
■ Properly ground washer to conform with all
governing codes and ordinances. Follow details
in Installation Instructions.
temperatures below freezing or exposed to the weather.
■ Remove the colored protective film from the
control panel.
YOUR LAUNDRY AREA
■ Keep the area underneath and around your
appliances free of combustible materials such as
lint, paper, rags, chemicals, etc.
■ Close supervision is necessary if this appliance is used
by or near children. Do not allow children to play on,
with, or inside this or any other appliance.
WHEN USING THE WASHER
■ Never reach into washer while it is moving. Wait
until the machine has completely stopped before
opening the lid.
■
The laundry process can reduce the flame retardancy
of fabrics. To avoid such a result, carefully follow the
garment manufacturer’s wash and care instructions.
T
rubleshotingT
■ Do not mix chlorine bleach with ammonia or acids
such as vinegar and/or rust remover. Mixing
different chemicals can produce a toxic gas which
may cause death.
■ To minimize the possibility of electric shock, unplug
this appliance from the power supply or disconnect
the washer at the household distribution panel by
removing the fuse or switching off the circuit breaker
before attempting any maintenance or cleaning.
NOTE: Pressing PAUSE or STOP/CANCEL does NOT
disconnect the appliance from the power supply.
Use this
appliance
only for its
intended
purpose as
described in
this Owner’s
Manual.
■ Do not wash or dry articles that have been cleaned in,
washed in, soaked in, or spotted with combustible or
explosive substances (such as wax, oil, paint, gasoline,
ips
degreasers, dry-cleaning solvents, kerosene, etc.) which ■ Never attempt to operate this appliance if it is damaged,
may ignite or explode. Do not add these substances to
the wash water. Do not use or place these substances
around your washer or dryer during operation.
malfunctioning, partially disassembled, or has missing
or broken parts, including a damaged cord or plug.
WHEN NOT IN USE
CustomSrvice
■ Turn off water faucets to relieve pressure on hoses
and valves and to minimize leakage if a break or
rupture should occur. Check the condition of the
fill hoses; they may need replacement after 5 years.
■ Do not attempt to repair or replace any part of this
appliance unless specifically recommended in this
Owner’s Manual, or in published user-repair
instructions that you understand and have the skills
to carry out.
■ Before discarding a washer, or removing it from
service, remove the washer lid to prevent children
from hiding inside.
■ Do not tamper with controls.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
About the control panel.
Your new washer offers the convenience of starting your wash loads by simply choosing a CLOTHES CARE SELECTION.
Then all you have to do is press START.
Quick Start Guide
SafeyIructions
CLOTHES CARE SELECTION
AUTO
WHITE COTTONS:
COLORED COTTONS:
BRIGHT COLORS:
PERM PRESS:
DELICATES:
START
SPIN
ONLY
SPIN ONLY:
PAUSE
FILL
WASH
RINS
• Close lid
• Select wash cycle
• Add clothes
• Push START
• Check load size setting
• Add detergent
• Add diluted fabric
softener
Model WNCD2050
OpeagIructions
CLOTHES CARE SELECTION
AUTOMATIC SETTINGS
LOAD
SIZE
WASH
HOT
AGITATION SPIN
START
EXTRA
LARGE
PAUSE
WHITE COTTONS:
NORMAL
FAST
FAST
FAST
FAST
SLOW
FAST
ips
COLORED COTTONS: WARM NORMAL
LARGE
MEDIUM
SMALL
STOP
BRIGHT COLORS:
PERM PRESS:
DELICATES:
COLD
WARM GENTLE
COLD GENTLE
NORMAL
CANCEL
SPIN
ONLY
SPIN ONLY:
EST. TIME
REMAINING
FILL
WASH
RINSE
FINAL SPIN
STATUS
rubleshotingT
T
CustomSrvice
4
Download from Www.Somanuals.com. All Manuals Search And Download.
About the control settings.
SafeyIructions
1
CLOTHES CARE SELECTION
For heavily to lightly soiled cottons, household linens, work and play clothes.
For heavily to lightly soiled cottons, household linens, work and play clothes.
For non-colorfast cottons and blends, and items that are labeled cold wash by the fabric manufacturer.
For knits, wrinkle-free and permanent press items.
OpeagIructions
For lingerie and items labeled delicate with light soils. Provides periods of agitation and soak during
wash and rinse.
SPIN
ONLY
Spin and drain any cycle at any time.
2
3
LOAD SIZE
A LOAD SIZE setting is automatically set when the CLOTHES CARE SELECTION is chosen. The LOAD SIZE
setting can be changed by pressing the pad for the size you want.
Loosely load clothes no higher than the top row of holes in the washer tub. The water level should just
cover the clothes.
EXTRA
LARGE
LARGE
SMALL
MEDIUM
T
rubleshotingT
START/PAUSE
Press START to begin the cycle. Pressing START again or raising the lid will PAUSE the cycle.
START
PAUSE
■ Press twice to select the last cycle used and start the washer.
ips
■ If the washer is running, press once to interrupt the cycle; press again to continue the cycle.
STOP/CANCEL
This pad should not be used to interrupt or pause a cycle.
STOP
CANCEL
Pressing this pad will cancel the current settings and the settings will be lost.
CustomSrvice
Estimated Time Remaining
■ Displays the approximate time remaining until the end of the cycle.
EST. TIME
REMAINING
■ If the estimated time remaining is more than 60 minutes, “1H” will flash in the display,
followed by the additional remaining minutes. When the time remaining is less than
60 minutes, the timer will count down.
■ Cycle time is affected by how long it takes the washer to fill. This depends on the water
pressure in your home. The “smart” timer “learns” the amount of time it takes to fill
your washer and adjusts the total time accordingly.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
About washer features.
Liquid Bleach Dispenser
The dispenser dilutes liquid chlorine bleach before it reaches into your wash load.
1 Check clothing care labels for special instructions.
2 Measure liquid bleach carefully, following instructions on the bottle.
■ Never pour undiluted liquid chlorine bleach directly onto clothes or into the wash basket.
■ Do not pour powdered bleach into bleach dispenser.
SafeyIructions
Before starting the washer, pour measured amount of bleach directly into bleach
3
dispenser. Avoid splashing or over-filling dispenser. If you prefer to use powdered
bleach, add it into the wash basket with your detergent.
■ Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover. Mixing can
produce a toxic gas which may cause death.
The Agitator Cap or Fabric Softener Dispenser
The agitator cap fits into the top of the
agitator. If it accidentally comes off, simply
put it back on.
Add water to dispenser until it reaches
the maximum fill line.
3
The fabric softener dispenser automatically
releases liquid fabric softener at the proper
time during the cycle.
OpeagIructions
Do not stop the washer during the first spin.
This will cause the dispenser to empty too
soon.
To use, follow these steps:
Do not pour anything into the agitator if
the agitator cap or dispenser is removed.
Make sure dispenser is securely attached
ips
1
to agitator.
Use only liquid fabric softener.
2
Pour into dispenser, using amount
recommended on package.
Never pour fabric softener directly on
clothes. It may stain them.
rubleshotingT
T
Cleaning the Fabric Softener Dispenser
1 Remove the dispenser from the top of the agitator.
Separate the dispenser cup from the cover by grasping the top and pushing down on
the inside of the cup with your fingers. Dispenser cup will pop free from the cover.
2
To clean the dispenser, soak both the dispenser cup and the dispenser cover in the
following solution:
3
■ 1 US gallon (3.8 liters) warm water
■ 1/4 cup (60 ml) heavy duty liquid detergent
■ 1 cup (240 ml) bleach
Separate for cleaning.
If necessary, loosen build-up with a clean, soft cloth after soaking. Do not use a stiff
brush; you may roughen the surface of the dispenser.
4
5 Rinse and reassemble dispenser. Place dispenser back on the agitator.
CustomSrvice
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading and using the washer.
Always follow fabric manufacturer’s care label when laundering.
SafeyIructions
Sorting Wash Loads
Sort by color (whites, lights, colors), soil level,
fabric type (sturdy cottons, easy care, delicates),
and whether the fabric produces lint (terry cloth,
chenille), or collects lint (velveteen, corduroy).
Proper Use of Detergent
Using too little or too much detergent is a common
cause of laundry problems.
You can use less detergent if you have soft water,
a smaller load, or a lightly soiled load.
OpeagIructions
Loading the Washer
Load dry items loosely, no higher than the top
row of holes in the washer basket. When loading
wet items make sure you set the load/water level
high enough to allow the items to move freely.
Water level should just cover the clothes. To add
items after washer has started, lift the lid and
submerge additional items next to the agitator.
■ Do not wrap long items like sheets or pants
around the agitator.
■ Do not wash fabrics containing flammable
materials (waxes, cleaning fluids, etc.).
■ Agitation will not start with the lid up.
T
rubleshotingT
ips
CustomSrvice
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading and using the washer.
Always follow fabric manufacturer’s care label when laundering.
Care and Cleaning of the Washer
Wash Basket: Leave the lid open after washing to
allow moisture to evaporate. If you want to clean the
basket use a clean soft cloth dampened with liquid
detergent, then rinse. (Do not use harsh or gritty
cleaners.)
Moving and Storage: Ask the service technician to
remove water from drain pump and hoses. Do not
store the washer where it will be exposed to the
weather. In the United States call the GE Answer
Center®, 800.626.2000 for information on how to
keep the tub stationary when moving the washer.
In Canada write to Manager, Consumer Relations,
Camco Inc., 1 Factory Lane, Suite 310, Moncton,
N.B. E1C 9M3.
SafeyIructions
Fill Hoses: Hoses connecting washer to faucet should
be replaced every 5 years.
Lint Filter: The lint filter is located under the agitator.
It is self-cleaning and requires no maintenance.
Long Vacations: Be sure water supply is shut off at
faucets. Drain all water from hoses if weather will
be below freezing.
Exterior: Immediately wipe off any spills. Wipe with
damp cloth. Try not to hit surface with sharp objects.
Fabric Care Labels
Below are fabric care label “symbols” that affect the clothing you will be laundering.
WASH LABELS
OpeagIructions
Machine
wash
cycle
Normal
Permanent Press/
wrinkle resistant
Do not wash
Do not wring
Gentle/
delicate
Hand wash
Water
temperature
Hot
(50°C/120°F)
Warm
(40°C/105°F)
Cold/cool
(30°C/85°F)
ips
DRY LABELS
Tumble
dry
Do not dry
(used with
do not wash)
Dry
Normal
Permanent Press/
wrinkle resistant
Gentle/
delicate
Do not tumble dry
rubleshotingT
T
Heat
setting
High
Medium
Low
No heat/air
Special
instructions
Dry flat
Line dry/
hang to dry
In the shade
Drip dry
BLEACH LABELS
Bleach
symbols
Any bleach
(when needed)
Do not bleach
c
Only non-chlorine bleach
(when needed)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you call for service…
SafeyIructions
Troubleshooting Tips
Save time and money! Review the charts on the following
pages first and you may not need to call for service.
PERFORMANCE
Clothes too wet
Possible Causes
What To Do
Incorrect spin speed
selected
• Make sure the spin cycle selected matches the load you
are washing. Some fabrics will feel wetter when rinsed
with cold water.
Colored spots
Incorrect use of fabric
softener
• Check fabric softener package for instructions and follow
directions for using dispenser.
• Pretreat stain and rewash.
OpeagIructions
Dye transfer
• Sort whites or lightly colored items from dark colors.
Grayed or yellowed
clothes
Not enough detergent
• Use more detergent (especially with larger loads)
Be sure to follow detergent manufacturer’s directions.
Hard water
• Use a water conditioner like Calgon brand or install
a water softener.
Water is not hot enough
Washer is overloaded
• Make sure water heater is delivering water at
120°F.–140°F. (48°C.–60°C.).
• Select load size to match clothes load.
Detergent is not
dissolving
• Add detergent as wash basket fills with water before
you load clothes.
Dye transfer
• Sort clothes by color. If fabric label states wash separately,
unstable dyes may be indicated.
Lint or residue on
clothes
Clothes are air or line dried
• If you do not dry your clothes with a clothes dryer, your
clothes may retain more lint.
T
rubleshotingT
Incorrect sorting
• Separate lint producers from lint collectors.
Washing too long
• Wash small loads for a shorter time than larger loads.
Detergent not dissolving
• Add detergent as wash basket fills with water, before you
load clothes.
• Try a liquid detergent.
• Use warmer water temperature.
ips
Overloading
• Load clothes no higher than the top row of holes in the
washer tub.
• Make sure load size selected matches clothes load size.
Incorrect use of fabric softener
• Check fabric softener package for instructions and follow
directions for using dispenser.
Pilling
Result of normal wear on
poly-cotton blends and
fuzzy fabrics
• While this is not caused by the washer, you can slow the
pilling process by washing garments inside out.
CustomSrvice
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you call for service…
Troubleshooting Tips
PERFORMANCE (cont.)
Possible Causes
What To Do
Snags, holes, tears, rips Pins, snaps, hooks, sharp
• Fasten snaps, hooks, buttons, and zippers.
or excessive wear
buttons, belt buckles,
zippers, and sharp objects
left in pockets
SafeyIructions
• Remove loose items like pins, objects in pockets
and sharp buttons.
• Turn knits (which snag easily) inside out.
Undiluted chlorine bleach
• Check bleach package instructions for proper amount.
• Never add undiluted bleach to wash or allow clothes
to come in contact with undiluted bleach.
Chemicals like hair bleach
or dye, permanent wave
solution
• Rinse items that may have chemicals on them before
washing.
Wrinkling
Improper sorting
• Avoid mixing heavy items (like work clothes) with
light items (like blouses).
• Try a fabric softener.
Overloading or
incorrect water level
• Load your washer so clothes have enough room
to move freely.
OpeagIructions
Incorrect wash and
dry cycles
• Match Cycle selection to the type of fabric you are
washing (especially for easy care loads).
Repeated washing in
water that is too hot
• Wash in warm or cold water.
ips
OPERATION
Possible Causes
What To Do
Washer pauses in cycle
The DELICATES cycle was chosen • This is normal. The DELICATES cycle has a short soak
period.
Washer won’t operate
Washer is unplugged
Water supply is turned off
Controls are not set properly
Lid is open
• Make sure cord is plugged securely into a working outlet.
• Turn both hot and cold faucets fully on.
• Check controls.
rubleshotingT
T
• Close lid.
Circuit breaker/fuse is
tripped/blown
• Check house circuit breakers/fuses. Replace fuses or
reset breaker. Washer should have separate outlet.
Electronics need to be reset
• Unplug washer, wait 2 minutes, plug back in,
and press START.
START was not pressed
• Press START.
Extremely low water pressure
• Press START again.
CustomSrvice
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SafeyIructions
WATER
Too many suds
Possible Causes
What To Do
Type of detergent
• Switch to a lower sudsing detergent brand and follow
instructions on package.
Very soft water
• Try less detergent.
Too much detergent
• Measure your detergent carefully. Use less soap if you
have soft water, a smaller load, or a lightly soiled load.
Water leaks
Fill hoses or drain hose is
improperly connected
• Make sure hose connections are tight at faucets
and at washer.
OpeagIructions
• Make sure end of drain hose is properly connected
to washer and correctly inserted in and secured to
drain facility.
Household drain may
be clogged
• Check household plumbing. You may need to call a
plumber.
Constant water pressure
to the fill hoses at the
water source
• Tighten hoses at the faucets and turn the water off after
each use.
• Check condition of the fill hoses; they may need
replacement after 5 years.
Using too much detergent
in washer
• Use less detergent. Use less soap if you have soft water, a
smaller load, or a lightly soiled load.
Water temperature
is incorrect
Control is not set properly
• Check water temperature control and adjust.
Water supply is turned off
or improperly connected
• Turn both hot and cold faucets fully on and make sure
hoses are connected to correct faucets.
T
rubleshotingT
Water valve screens are
stopped up
•
Turn off the water source and remove the water connection
hoses from the upper back of the washer. Use a brush or
toothpick to clean the screens in the machine. Reconnect
the hoses and turn the water back on.
House water heater is
not set properly
• Make sure house water heater is delivering water
at 120°F.–140°F.(48°C.–60°C.).
ips
Water pumped out
before cycle is
complete
Lid lifted or cycle was put in
pause for over 24 hours
• Reset cycle.
Water won’t drain
Drain hose is kinked or
improperly connected
• Straighten drain hose and make sure washer is not sitting
on it.
• Top of drain outlet should be less than 8 ft (2.5 m)
above floor.
CustomSrvice
Water spraying during
spin cycle
Washer in spin cycle
• Spray rinse during a spin cycle is normal.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you call for service…
Troubleshooting Tips
WATER (cont.)
Possible Causes
What To Do
Washer did not fill to
chosen level
(START/PAUSE lights
are flashing)
Extremely low water pressure
Inlet hoses are kinked
• Press the START button again.
• Straighten hoses.
SafeyIructions
Water valve screens are
stopped up
•
Turn off the water source and remove the water connection
hoses from the upper back of the washer. Use a brush or
toothpick to clean the screens in the machine. Reconnect
the hoses and turn the water back on.
Water fills and drains
at the same time
Drain stand pipe is too low
• Drain stand pipe must be above 30″.
NOISE
Possible Causes
What To Do
Washer is noisy
Washer is uneven
• To level the front of the washer, adjust the front leveling
legs by rotating the individual leg in the proper direction
for up or down. To level back of washer, lift back of
machine 4″ (11 cm) and set down.
OpeagIructions
Washer load is
unbalanced
• Press PAUSE to stop the washer, open the lid and
redistribute the load evenly. Close the lid and press
START.
Shipping rod is still assembled
in unit
• To remove shipping rod from washer, pull yellow tag and
attached rod from the bottom right hand side of washer.
ips
Washer is sitting too close
to wall (causes knocking
during cycle)
• Pull washer away from the wall; about 4″ (11 cm)
is needed.
OTHER
Possible Causes
What To Do
rubleshotingT
Labels on the exterior
of the washer will not
peel off cleanly
Occasionally the adhesive
used on the labels does
not release cleanly
• Use a hair dryer set at the lowest heat setting, directing
the air at the label for a short amount of time. This will
release the adhesive easily, without damaging the surface
of the washer.
T
CustomSrvice
12
Download from Www.Somanuals.com. All Manuals Search And Download.
™
GE Service Protection Plus
GE, a name recognized worldwide for quality and dependability, offers you
™
Service Protection Plus —comprehensive protection on all your appliances—
No Matter What Brand!
Benefits Include:
• Backed by GE
• All brands covered
• Unlimited service calls
• All parts and labor costs included
• No out-of-pocket expenses
• No hidden deductibles
• One 800 number to call
We’ll Cover Any Appliance.
Anywhere. Anytime.*
You will be completely satisfied with our service protection or you may request your money back
on the remaining value of your contract. No questions asked. It’s that simple.
Protect your refrigerator, dishwasher, washer and dryer, range, TV, VCR and much more—any brand!
Plus there’s no extra charge for emergency service and low monthly financing is available. Even icemaker
coverage and food spoilage protection is offered. You can rest easy, knowing that all your valuable
household products are protected against expensive repairs.
Place your confidence in GE and call us in the U.S. toll-free at 800-626-2224
for more information.
*All brands covered, up to 20 years old, in the continental U.S.
Cut here
✁
Please place in envelope and mail to:
General Electric Company
Warranty Registration Department
P.O. Box 32150
Louisville, KY 40232-2150
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Product Ownership Registration
Dear Customer:
Thank you for purchasing our product and thank you for placing your confidence in us.
We are proud to have you as a customer!
Follow these three steps to protect your new appliance investment:
Complete and mail
your Consumer
After mailing the
registration below,
store this document
in a safe place. It
contains information
you will need should
you require service.
Our service number is
800 GE CARES
Read your Owner’s
Manual carefully.
It will help you
operate your new
appliance properly.
Product Ownership
Registration today.
Have the peace of
mind of knowing we
can contact you in the
unlikely event of
a
safety modification.
1
2 3
(800-432-2737).
Model Number
Serial Number
Important: If you did not get a registration card with your
product, detach and return the form below to
ensure that your product is registered, or register
Cut here
✁
Consumer Product Ownership Registration
Model Number
Serial Number
Mr. ■ Ms. ■ Mrs. ■ Miss ■
First
Name
Last
Name
Street
Address
Apt. #
City
E-mail Address
Zip
Code
State
Date Placed
In Use
Month
Phone
Number
_
_
Day
Year
Occasionally, we may allow selected companies to send you information.
■ Check here if you do not want this information.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
GE Washer Warranty
WNCD2050
SafeyIructions
All warranty service provided by our Factory Service Centers or an authorized Customer Care®
technician. For service, in the United States, call 1-800-GE-CARES. In Canada, call 1-800-361-3400.
For The Period Of: We Will Replace:
One Year
From the date of the
original purchase
Any part of the washer which fails due to a defect in materials or workmanship. During this
full one-year warranty, we will also provide, free of charge, all labor and in-home service to replace
the defective part.
What Is Not Covered (for customers in the United States):
■ Service trips to your home or business to teach you how
■ Replacement of fuses or resetting of circuit breakers.
■ Damage to product caused by accident, fire, floods or
acts of God.
OpeagIructions
to use the product.
■ Improper installation.
■ Failure of the product if it is abused, misused, or used
for other than the intended purpose.
■ Incidental or consequential damage caused by possible
defects with this appliance.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for use within the USA. In Alaska, the
warranty excludes the cost of shipping or service calls to your home or business.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state. To know what your legal rights are, consult your local or state consumer affairs office or
your state’s Attorney General.
Warrantor: General Electric Company. Louisville, KY 40225
What Is Not Covered (for customers in Canada):
■ Service trips to your home or business to teach you how
■ Replacement of fuses or resetting of circuit breakers.
■ Failure of the product if it is misused, or used for
other than the intended purpose.
to use the product.
T
rubleshotingT
■ Improper installation.
If you have an installation problem, contact your
dealer or installer. You are responsible for providing
adequate electrical, exhausting and other connecting
facilities.
■
Damage to product caused by accident, fire, floods or
acts of God.
WARRANTOR IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES.
Warrantor: CAMCO INC.
ips
CustomSrvice
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Telephone Numbers.
GE Answer Center® In the U.S.: 800-626-2000
The GE Answer Center® is open 24 hours a day, 7 days a week.
In Canada, contact: Manager, Consumer Relations, Camco Inc., 1 Factory Lane, Suite 310,
Moncton, N.B., E1C 9M3.
OR
Visit our Website at www.geappliances.com
SafeyIructions
In-Home Repair Service In the U.S.: 800-432-2737
Expert GE repair service is only a phone call away.
In Canada, call 1-800-361-3400.
Special Needs Service In the U.S.: 800-626-2000
GE offers, free of charge, a brochure to assist in planning a barrier-free kitchen for persons
with limited mobility. In the U.S., call 800-TDD-GEAC (800-833-4322).
In Canada, contact: Manager, Consumer Relations, Camco Inc., 1 Factory Lane, Suite 310,
Moncton, N.B., E1C9M3.
OpeagIructions
Service Contracts In the U.S.: 800-626-2224
Purchase a GE service contract while your warranty is still in effect and you’ll receive a
substantial discount. GE Consumer Service will still be there after your warranty expires.
ips
In Canada, call 1-800-461-3636.
Parts and Accessories In the U.S.: 800-626-2002
Individuals qualified to service their own appliances can have parts or accessories sent directly
to their homes (VISA, MasterCard and Discover cards are accepted).
rubleshotingT
T
Instructions contained in this manual cover procedures to be performed by any user. Other servicing
generally should be referred to qualified service personnel. Caution must be exercised, since
improper servicing may cause unsafe operation.
In Canada, call 1-800-361-3400.
Service Satisfaction
If you are not satisfied with the service you receive from GE:
First, contact the people who serviced your appliance.
Next, if you are still not pleased, in the U.S., write all the details—including your phone number—to:
Manager, Customer Relations, GE Appliances, Appliance Park, Louisville, KY 40225; or,
in Canada, to Director, Consumer Relations, Camco Inc., 1 Factory Lane, Suite 310, Moncton, N.B.,
E1C 9M3.
CustomSrvice
16
Printed in Louisville, KY
Download from Www.Somanuals.com. All Manuals Search And Download.
|