GE Telephone 29273 User Manual

1. Rotate the handset hook tab to an upright position.  
2. Push the button on the cradle and remove the  
cradle bracket.  
To answer an incoming call while having a conversation:  
REDIALING A NUMBER  
If you want to call the last number you dialed again (up to 32 digits), use the  
redial feature.  
29273  
INTRODUCTION  
TROUBLESHOOTING TIPS  
After you hear the Call Waiting tone, press and release the flash button.The first  
call is placed on hold while the second call can be answered.  
Trimline Memory Phone  
with Call Waiting Caller ID  
User's Guide  
NO DIAL TONE  
CAUTION: When using telephone equipment, there are basic safety  
instructions that should always be followed. Refer to the IMPORTANT  
SAFETY INSTRUCTIONS provided with this product and save them for  
future reference.  
3. Rotate bracket 180 degrees and put it back on  
the base.  
Check all cabling to make sure that all connections are secure and not damaged.  
Check the hook switch: Does it fully extend when handset is lifted from cradle?  
To return to your first call and put the second call on hold:  
1. Pick up the handset.  
Press and release flash again.The first call can continue while the second call is  
put on hold.  
2. Press the redial button.  
4. Plug one end of the straight telephone line cord  
into the jack on the bottom of the base.  
NO DISPLAY  
Your Caller ID phone stores and displays specific information, provided by your local  
telephone company, to subscribers of Caller ID or similar caller identification services.  
3. The last number called is automatically redialed.  
Replace batteries.  
Make sure the batteries are properly installed.  
5. Feed the line cord through the groove and wrap  
the cord around the track on the bottom of the  
base.  
USING TEMPORARY TONE DIALING  
USING ONE TOUCH REDIAL  
If the last call you dialed was busy, you can redial it immediately by just pressing  
the redial button and without hanging up the handset.  
Your Caller ID phone enables you to:  
NO INFORMATION IS SHOWN AFTER THE PHONE RINGS  
If you have pulse service, you can temporarily change from pulse to tone service.  
After dialing the telephone number, press and release the *TONE button on the  
telephone.This allows access to phone services that require a tone, such as banking  
and long-distance services. After you hang up the handset, the telephone  
automatically returns to pulse service.  
Identify callers before you answer the phone.  
View the time and date of each incoming call.  
Record up to 75 Caller ID messages sequentially.  
Know who called while you were away.  
In order to receive Caller ID records, you must subscribe to the standard name  
and number Caller ID service available through your local telephone company.  
Be sure to wait until the second ring before answering.  
6. Feed the line cord through the groove on the  
opposite side of the track, and plug the end into  
the modular telephone jack.  
NOTE: This feature may not perform if the battery power is low.  
PHONE DOES NOT RING  
7. Slip the mounting holes (on the bottom of the base) over the wall plate posts  
and firmly slide the unit down into place.  
Make sure ringer switch is set to HI.  
You may have too many extension phones on your line. Unplug some  
extension phones.  
MEMORY  
CALLER ID (CID) FEATURES  
To get the most from your new phone, we suggest that you take a few minutes right now  
to read through this users guide.  
Before you store a telephone number in memory, make sure the dialing mode is  
correctly set for the type of service you have.The default dialing mode is tone  
(touch-tone), so if you have pulse (rotary) service, you must first change the dialing  
mode. See “To Set the Dial Mode.The following buttons can be stored into any  
memory location:0-9, A, B, C.  
HANDSET LAYOUT  
Check for a dial tone. If there is no dial tone see solutions for "No dial tone."  
IMPORTANT: In order to use all the features of this unit, you must subscribe to  
the standard Name/Number Caller ID Service or Call Waiting Caller ID Service  
available from your local telephone company. To know who is calling while you  
are on the phone, you must subscribe to Call Waiting Caller ID Service.  
New calls  
Current time  
Current date  
OTHER PARTY CANNOT HEAR YOU  
Make sure phone cord is securely plugged in.  
volume  
switch  
Make sure extension phones are on the hook at the same time you're using the  
phone. It is normal for the volume to drop when additional extension phones are  
used at the same time.  
STORING FREQUENTLY CALLED NUMBERS  
1. Pick up the handset.  
BEFORE YOU BEGIN  
arrow buttons  
display  
PARTS CHECKLIST  
mem button  
CANNOT DIAL OUT  
2. Press the store button.  
Make sure your package includes the following items:  
Make sure theT/P dialing mode is set to the type of phone service you are  
subscribed to.  
3. Push the desired memory location button.  
4. Press the store button.  
delete button  
dial button  
options  
button  
SERVICE  
5. Use the handset number keys to enter the telephone number (up to 32 digits  
for 0-9 and A, B, C locations) and press the store button.  
If trouble is experienced with this equipment, for repair or warranty information,  
please contact customer service at 1-800-448-0329. If the equipment is causing harm  
to the telephone network, the telephone company may request that you disconnect  
the equipment until the problem is resolved.  
6. Press the store button and hang up the handset.  
Caller ID name  
Caller ID number  
store button  
redial button  
NOTE: If you make a mistake, use the delete button to delete wrong digits.  
This product may be serviced only by the manufacturer or its authorized service  
agents. Changes or modifications not expressly approved by ATLINKS USA, Inc.  
could void the users authority to operate this product. For instructions on how to  
obtain service, refer to the warranty included in this guide or call customer service  
at 1-800-448-0329.  
SUMMARY SCREEN  
The Summary Screen shows the current time, current date, and number of new  
calls to be reviewed. It displays until any button is pressed. Within 60 seconds of  
receiving a new call, the Summary Screen displays.  
CHANGING A STORED NUMBER  
Repeat the storage sequence above.The new number replaces the old number at  
the memory location.  
flash button  
Base  
Handset  
Coiled cord  
Telephone line cord  
Wall plate  
SETTING UP THE CALLER ID MENU  
ERASING A STORED NUMBER  
1. Pick up the handset.  
Or refer inquiries to:  
ATLINKS USA, Inc.  
Manager, Consumer Relations  
P O Box 1976  
TELEPHONE JACK REQUIREMENTS  
NOTE: The number of new calls shows in the display until all new calls are reviewed.  
IMPORTANT: Do not plug the telephone into the wall jack while setting up the Caller  
ID menu because an incoming call may invalidate the information not yet saved.  
To use this phone, you need an RJ11C type modular  
telephone jack, which might look like the one pictured  
here, installed in your home. If you don’t have a modular  
jack, call your local phone company to find out how to get  
one installed.  
Telephone  
line jack  
2. Press the store button.  
RECEIVING AND STORING CID RECORDS  
1. Place the handset in the cradle on the base.  
3. Press the memory location (0-9, A, B, C) to be erased.  
4. Press delete for three seconds until the number in the display is erased.  
5. Hang up the handset.  
We bring good things to life.  
This unit receives and displays CID information transmitted by your local phone company.  
This information can include the phone number, date, and time; or the name, phone  
number, date, and time.The unit stores up to 75 call records for later review.When the  
memory is full, a new call record automatically replaces the oldest call record in memory.  
NEW shows in the display for call records received which have not been reviewed.  
Indianapolis, IN 46206  
2. Press the options button. SET OR appears in the display.  
Attach your sales receipt to the booklet for future reference or jot down the date this  
product was purchased or received as a gift.This information will be valuable if  
service should be required during the warranty period.  
3. Press either REVIEW up or down button to scroll among the 7 menu screens,  
which are:  
IMPORTANT INSTALLATION INFORMATION  
EQUIPMENT APPROVAL INFORMATION  
SET OR ꢁ  
DIALING FREQUENTLY CALLED NUMBERS  
Your telephone equipment is approved for connection to the Public SwitchedTelephone Network and  
is in compliance with parts 15 and 68, FCC Rules and Regulations and theTechnical Requirements for  
TelephoneTerminal Equipment published by ACTA.  
Purchase date  
Name of store  
LOCAL AREA CODE (default - - -)  
CID LANGUAGE (default English)  
SELECT CONTRAST (default 3)  
CAUTION: Disconnect the phone cord from the wall outlet  
before installing or replacing the batteries.  
1. Pick up the handset and press the mem button.  
2. Press 0-9, A, B, C for the memory location.The number dials automatically.  
OR  
REVIEWING CID RECORDS  
Press either the > (+) or < (-) down button to view the newest call record.  
1
Notification to the LocalTelephone Company  
Never install wiring during a lightning storm.  
On the bottom of this equipment is a label indicating, among other information, the US  
number and Ringer Equivalence Number (REN) for the equipment.You must, upon request,  
provide this information to your telephone company.  
Press the < (-) button to scroll through the call records from the most recent to  
the oldest.  
T/P DIAL MODE (default tone)  
EXIT SETUP  
LIMITED WARRANTY  
What your warranty covers:  
1. Pick up the handset and press the dial button.  
2. Press the review button for the desired memory location.  
3. Press the dial button to dial the number.  
OR  
Never touch non-insulated telephone wires or terminals, unless the telephone line  
has been disconnected at the network interface.  
Press the > (+) button to scroll through the call records from the oldest to  
the newest.  
The REN is useful in determining the number of devices you may connect to your telephone  
line and still have all of these devices ring when your telephone number is called. In most (but  
not all) areas, the sum of the RENs of all devices connected to one line should not exceed 5.To  
be certain of the number of devices you may connect to your line as determined by the REN,  
you should contact your local telephone company.  
Use caution when installing or modifying telephone lines.  
Defects in materials or workmanship.  
NOTE: You may press dial anytime to exit the Caller ID Set Up menu.  
If no buttons are pressed within 10 seconds, the phone automatically exists  
the Caller ID Set Up menu and returns to the NO CALLS summary screen.  
Never install telephone jacks in wet locations unless the jack is specifically  
designed for wet locations.  
For how long after your purchase:  
When all of the messages have been viewed, START/END appears in the display.  
One year, from date of purchase.  
1. Press dial button while the handset is still in the cradle.  
(The warranty period for rental units begins with the first rental or 45 days from date of  
shipment to the rental firm, whichever comes first.)  
INSTALLING THE BATTERIES  
DELETING CID RECORDS  
A plug and jack used to connect this equipment to the premises wiring and telephone network  
must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A  
compliant telephone cord and modular plug is provided with this product. It is designed to be  
connected to a compatible modular jack that is also compliant. See installation  
instructions for details.  
2. Press the review button for the desired memory location, lift the handset and the  
number dials automatically.  
LOCAL AREA CODE (LAC)  
The telephone uses the programmed area code to determine the number  
format to display when a valid Caller ID signal is received. It is also used  
for the Dialback feature.  
To delete the record showing in the display, press the delete button once.  
IMPORTANT: You will have approximately 60 seconds to replace the  
batteries before the memories stored in the handset are lost. Please read  
the instructions before replacing the batteries and have the batteries ready  
to be inserted beforehand. As a precaution, you may want to write down  
any stored information you do not want erased.  
What we will do:  
Provide you with a new or, at our option, a refurbished unit.The exchange unit is under  
warranty for the remainder of the original products warranty period.  
How you get service:  
To delete all records while reviewing, press and hold the delete button until  
ERASE ALL? shows in the display, then release the delete button and press again  
to erase all CID records.  
REVIEWING NUMBERS STORED IN MEMORY  
1. Press the store button.  
Notes  
This equipment may not be used on coin service provided by the telephone company.  
Properly pack your unit. Include any cables, etc., which were originally provided with the  
product. We recommend using the original carton and packing materials.  
1. Place the handset in the cradle on the base.  
2. Press 0-9, A, B, C for the memory location.The number shows on the display.  
Party lines are subject to state tariffs, and therefore, you may not be able to use your own  
telephone equipment if you are on a party line. Check with your local telephone company.  
Notice must be given to the telephone company upon permanent disconnection of your  
telephone from your line.  
DIALING BACK  
Your Caller ID phone uses 4 AA-size alkaline batteries for receiving and storing Caller  
ID records and for the numbers you use for memory dialing.  
2. Press the options button. SET OR appears in the display.  
3. Press the > (+) button until LOCAL AREA CODE:_ _ _ appears in the display.  
COPY CALLER ID MEMORY TO USER MEMORY  
1. Pickup the handset.  
”Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the  
product is within the warranty period, must be presented to obtain warranty service.” For  
rental firms, proof of first rental is also required. Also print your name and address and a  
description of the defect. Send via standard UPS or its equivalent to:  
When reviewing Caller ID records, you may dialback the phone numbers shown on  
the display by pressing the dial button.  
1. If both the straight and coiled line cords are already connected, disconnect them  
from the base unit. Place the handset aside.  
If your home has specially wired alarm equipment connected to the telephone line, ensure the  
installation of this product does not disable your alarm equipment. If you have questions  
about what will disable alarm equipment, consult your telephone company or a qualified  
installer.  
4. To enter or change the area code, press the options button.The display shows  
the area code stored in memory.The left-most digit, or a minus sign (-) flashes,  
indicating the unit is ready to accept the area code entry.  
2. Press either review (< or >) button to display the number you want to copy.  
3. Press the store button.  
IF YOU PROGRAMMED YOUR LOCAL AREA CODE IN THE SETUP MENU  
1. Use the > (+) and < (-) buttons to scroll to the number you want to dial.  
ATLINKS USA, Inc.  
c/o Thomson  
Socorro,Texas 79927  
2. Push the button on the cradle and pull out the cradle bracket.  
3. Insert 4 AA-size alkaline batteries (not included) as shown on the diagram  
inside the compartment.  
4. Press 0-9, A, B, C for the memory location.The display flashes if the memory  
location is occupied.  
If you see a number with 7 digits (i.e. 555-1234), then the call was received from  
within your area code. However, this does not guarantee the call is a local call.  
2
Rights of theTelephone Company  
5. Press < (-) and select a number from 9-0 for the first digit.  
Pay any charges billed to you by the Exchange Center for service not covered by the warranty.  
Insure your shipment for loss or damage. ATLINKS accepts no liability in case of damage or loss.  
A new or refurbished unit will be shipped to you freight prepaid.  
Should your equipment cause trouble on your line which may harm the telephone network,  
the telephone company shall, where practicable, notify you that temporary discontinuance of  
service may be required. Where prior notice is not practicable and the circumstances warrant  
such action, the telephone company may temporarily discontinue service immediately. In case  
of such temporary discontinuance, the telephone company must: (1) promptly notify you of  
such temporary discontinuance; (2) afford you the opportunity to correct the situation; and (3)  
inform you of your right to bring a complaint to the Commission pursuant to procedures set  
forth in Subpart E of Part 68, FCC Rules and Regulations.  
6. When the desired digit is flashing, press > (+) to advance to the next digit.  
7. Repeat steps 5 and 6 until all the digits for your area code are correct.  
4. Replace the battery compartment door.  
5. Put the cradle bracket back on the base.  
5. Press the store button twice to replace the new information with the old, or press  
either review (< or >) button to select an empty location.The number is  
automatically stored.  
If you see a number with 11 digits (i.e. 1-234-555-1234), then the call received was not  
from your area code.  
What your warranty does not cover:  
6. Re-attach the line cords to the unit and check your memory locations. If installation takes  
longer than 90 seconds, you should re-set your memory locations.  
2. Press the dial button and the display shows PICKUP or ADJ. A 10 second timer  
also starts in the upper right side of the display, letting you know the time  
remaining until the unit returns to the Summary Screen. If you adjust the number  
to be dialed, the timer automatically resets itself.  
Customer instruction. (Your Owners Manual provides information regarding operating instructions  
and user controls. Any additional information, should be obtained from your dealer.)  
NOTE: If you make a mistake, you can simply repeat the previous steps until  
6. Press the hook switch to exit.  
your area code is set.  
Installation and setup service adjustments.  
Batteries.  
COPY REDIAL MEMORY TO USER MEMORY  
1. Pickup the handset.  
IMPORTANT: If you’re not going to use the telephone for more than 30 days,  
remove the batteries because they can leak and damage the unit.  
8. Press options to store the area code and return to the LAC display.  
The telephone company may make changes in its communications facilities, equipment,  
operations or procedures where such action is required in the operation of its business and not  
inconsistent with FCC Rules and Regulations. If these changes are expected to affect the use or  
performance of your telephone equipment, the telephone company must give you adequate  
notice, in writing, to allow you to maintain uninterrupted service.  
Damage from misuse or neglect.  
3. To adjust the phone number, press the dial button. For instance, a 7-digit  
local number sometimes cannot be dialed because it requires a 10-digit or  
11-digit format. Press the dial button repeatedly to scroll through the 7, 10,  
and 11-digit numbers.  
CID LANGUAGE  
2. Press store.  
Products which have been modified or incorporated into other products.  
Products purchased or serviced outside the USA.  
Acts of nature, such as but not limited to lightning damage.  
This setting allows you to display Caller ID messages in English, French or Spanish.  
3. Press 0-9, A, B, C for the memory location.The display flashes if the memory  
location is occupied. Press either review (< or >) button to select a different  
location.The display flashes if the memory location is occupied.  
Battery compartment  
1. Place the handset in the cradle on the base.  
7-digits:  
7-digit telephone number (i.e. 555-5555)  
INTERFERENCE INFORMATION  
Limitation of Warranty:  
2. Press the options button. SET OR appears in the display.  
3. Press the > (+) button until CID LANGUAGE appears in the display.  
4. Press the store button again to confirm.  
THE WARRANTY STATED ABOVE ISTHE ONLY WARRANTY APPLICABLETOTHIS PRODUCT. ALL  
OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF  
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO  
VERBAL OR WRITTEN INFORMATION GIVEN BY ATLINKS USA, INC., ITS AGENTS, OR EMPLOYEES  
SHALL CREATE A GUARANTY OR IN ANY WAY INCREASETHE SCOPE OFTHIS WARRANTY.  
This equipment has been tested and found to comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential installation.  
10-digits: 3-digit area code + 7-digit telephone number (i.e. 425-555-5555)  
5. Press the redial button, and then press the store button again.  
6. Press the flash button or the hook switch to exit.  
11-digits: long distance code 1 + 3-digit area code + 7-digit telephone  
4. Press the options button to show the current language setting.The default is  
English.  
number (i.e. 1-425-555-5555)  
This equipment generates, uses, and can radiate radio frequency energy and, if not installed  
and used in accordance with the instructions, may cause harmful interference to radio  
5. Press the > (+) or < (-) button to change the language.  
STORING A PAUSE IN MEMORY  
REPAIR OR REPLACEMENT AS PROVIDED UNDERTHIS WARRANTY ISTHE EXCLUSIVE  
REMEDY OFTHE CONSUMER. ATLINKS USA, INC. SHALL NOT BE LIABLE FOR INCIDENTAL  
OR CONSEQUENTIAL DAMAGES RESULTING FROMTHE USE OFTHIS PRODUCT OR ARISING  
OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ONTHIS PRODUCT.THIS  
DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED BYTHE LAWS OF  
THE STATE OF INDIANA. EXCEPTTOTHE EXTENT PROHIBITED BY APPLICABLE LAW, ANY  
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON  
THIS PRODUCT IS LIMITEDTOTHE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.  
c
ommunications. However, there is no guarantee that interference will not occur in a  
4. To dial the displayed number, pick up the handset before the timer reaches 0.  
NOW DIALING shows in the display and the number is dialed.  
6. Press options to store the language and return to the CID LANGUAGE display.  
particular installation.  
The redial button has dual functionality. It becomes a pause button if the store  
button is pressed first. It is valid only when storing a number into memory. Use the  
redial button to insert a pause when a delay is needed in an automatic dialing  
sequence. For example, when you must dial a 9 to get an outside line, or when you  
enter codes to access your long distance company.  
INSTALLING THE PHONE  
Choose the best location to install your telephone.Your telephone should be placed on a  
level surface, such as a desk or table top, or you may mount it on the wall.  
If this equipment does cause harmful interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
SELECT CONTRAST  
This adjustment allows you to adjust the contrast and viewing angle of the display.  
IF YOU DID NOT PROGRAM YOUR LOCAL AREA CODE IN THE SETUP MENU  
1. Use the > (+) and < (-) buttons to display the number you want to dial.You will  
only see 10-digit numbers (i.e. 234-555-1234).  
Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving”  
the interference).  
1. Place the handset in the cradle on the base.  
You may need to adjust the length of the pause. It can be adjusted from 1 to 9 seconds.  
The default setting is 4 seconds.  
2. Press the options button until SET OR appears.  
3. Press the > (+) button until SELECT CONTRAST appears in the display.  
Reorient or relocate and increase the separation between the telecommunications equipment  
and receiving antenna.  
How state law relates to this warranty:  
2. See steps 2 through 4 in the above section to complete the dialback sequence.  
Some states do not allow the exclusion nor limitation of incidental or consequential  
damages, or limitations on how long an implied warranty lasts so the above limitations or  
exclusions may not apply to you.  
Connect the telecommunications equipment into an outlet on a circuit different from that  
to which the receiving antenna is connected.  
1. Pickup the handset.  
NOTE: IF PICKUP PHONE shows on the display, no other changes to the  
number can be made. The information sent from the telephone company is  
known to be a valid number to dial back (available only in limited areas). Once  
you pickup the phone, the number is automatically dialed.  
4. Press the options button to show the current contrast setting.There are 5 levels  
of contrast, with the default set to 3.  
2. Press the store button.  
3. Press the redial button.  
4. Press 1-9 (1 = 1 second, 2 = 2 seconds, etc.)  
If these measures do not eliminate the interference, please consult your dealer or an experienced radio/  
television technician for additional suggestions. Also, the Federal Communications Commission has  
prepared a helpful booklet, “HowTo Identify and Resolve Radio/TV Interference Problems.”This booklet is  
available from the U.S. Government Printing Office, Washington, D.C. 20402. Please specify stock number  
004-000-00345-4 when ordering copies.  
This warranty gives you specific legal rights, and you also may have other rights that vary  
from state to state.  
5. To decrease the contrast, press < (-). To increase the contrast, press > (+).  
handset hook  
If you purchased your product outside the USA:  
This warranty does not apply. Contact your dealer for warranty information.  
6. Press the options button to store the contrast setting and return to the  
SELECT CONTRAST display.  
5. Press store again.  
CALLER ID DISPLAY MESSAGES  
The following special messages indicate the status of a message or the unit:  
6. Press the flash button or the hook switch to exit.  
T/P DIAL MODE  
This adjustment allows you to select tone (touch-tone) or pulse (rotary) dialing.  
HEARING AID COMPATIBILITY (HAC)  
CONNECTING THE TELEPHONE LINE  
1. Plug the coiled cord into the jack on the handset and the jack on the end of  
the base.  
NO CALLS  
The caller memory is empty.  
CHAIN DIALING  
This telephone system meets FCC standards for Hearing Aid Compatibility.  
UNKNOWN CALLER  
The incoming call does not have Caller ID service or  
their service area is not linked to yours. If UNKNOWN  
CALLER appears along with a calling number, the name  
information for that number is not available.  
1. Place the handset in the cradle on the base.  
US NUMBER IS LOCATED ONTHE CABINET BOTTOM  
REN NUMBER IS LOCATED ONTHE CABINET BOTTOM  
This process allows you to dial a succession of stored numbers from separate  
memory locations.This is useful when you must dial several sequences of numbers,  
such as with frequent calls via a telephone company long distance provider.  
2. Press the options button until SET OR appears.  
2. Plug the long straight line cord into jack on the bottom of the base, and plug the  
other end into a modular telephone jack.  
3. Press the > (+) button until T/P DIAL MODE appears in the display.  
For example  
Memory location  
CAUTION:  
3. Set the RINGER switch on the base to HI.  
4. Press the options button to show the current dial mode.The default is set to  
tone.  
Battery power level is low. Please replace the batteries  
as soon as possible in order to maintain Caller ID operation.  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
Local access number of long distance company  
Authorization code (ID)  
6
7
8
2 = HI - Sound will be loudest.  
5. To change the dialing mode, press the > (+) or < (-) button.The display will  
alternate between the two dialing modes.  
THE EXCLAMATION  
POINT WITHIN THE  
TRIANGLE IS A  
THE LIGHTNING  
CAUTION: TO REDUCE THE  
BLOCKED CALL  
START/END  
The incoming caller is registered as “Private Number” and  
Caller ID information is withheld.  
= LOW - Sound will be lower.  
1
FLASH AND ARROW RISK OF ELECTRIC SHOCK, DO  
HEAD WITHIN THE NOT REMOVE COVER (OR  
WARNING:TO  
Long distance phone number  
1. Pick up the handset.  
0 = OFF -Telephone will not ring.  
WARNING SIGN  
ALERTING YOU OF  
IMPORTANT  
PREVENT FIRE OR  
ELECTRICAL SHOCK  
HAZARD, DO NOT  
EXPOSETHIS  
TRIANGLE IS A  
WARNING SIGN  
ALERTING YOU OF  
“DANGEROUS  
VOLTAGE” INSIDE  
THE PRODUCT.  
BACK). NO USER  
6. Press the options button to store the dialing mode and return to the T/P DIAL  
MODE display.  
You are at the beginning or the end of the Caller ID  
memory log.  
SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO  
QUALIFIED SERVICE  
PERSONNEL.  
4. Place the handset in the cradle.  
2. Press mem button, then press number “6” for the memory location.  
3. Press mem button, then press number “7” for the memory location.  
4. Press mem button, then press number “8” for the memory location.  
5. The number dials automatically.  
INSTRUCTIONS  
ACCOMPANYING  
THE PRODUCT.  
NOTE: The unit is properly installed if you pick up the handset and hear the  
dial tone. Otherwise, recheck all the installation steps.  
If you subscribe to Call Waiting Caller ID Service,  
this icon flashes when you receive a call while you are  
on the phone.  
CALL WAITING  
EXIT SETUP  
PRODUCT TO RAIN  
OR MOISTURE.  
To immediately exit the setup mode, select the EXIT SETUP menu and press the  
options button.  
SEE MARKING ON BOTTOM / BACK OF PRODUCT  
WALLMOUNTING THE PHONE  
Your telephone may also be mounted on the wall (wall plate not included).  
REMINDER: The time and date is programmed automatically when the first  
Caller ID record is successfully received after the unit is setup.  
USING FLASH  
NOTE: To prevent the handset from falling out of the cradle while the phone is  
hanging on the wall, you must reverse the handset hook (located on the base).  
This feature is used to activate customer calling services available through your local  
phone company, such as Call Waiting.These services generally require an extra  
monthly fee. If you subscribe to any of these services, please refer to the phone  
companys instructions on how to use flash.  
TELEPHONE BASICS  
ATLINKS USA, Inc.  
ADJUSTING THE VOLUME  
You may control the listening level with the VOLUME switch, which has three levels.  
Model 29273  
55927840 (Rev. 2 E/S)  
04-31  
101 West 103rd Street  
Indianapolis, IN 46290  
© 2004 ATLINKS USA, Inc.  
Trademark(s) ® Registered  
Marca(s) Registrada(s)  
It remains at the last level set until you change it.  
Printed in China  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Extron electronic Stereo Amplifier MPA 401 User Manual
FMI Indoor Fireplace CGMFN User Manual
Frymaster Fryer 17BC User Manual
FujiFilm Digital Camera S600 Zoom Date User Manual
Fujitsu Laptop S 5582 User Manual
GBC Paper Shredder 5230S User Manual
GE Microwave Oven 164 D2092P021 User Manual
GE Microwave Oven JE1235 User Manual
Generac Pressure Washer 1537 0 User Manual
GE Ventilation Hood JV694S User Manual