GE Refrigerator 2 Cubic Foot Models User Manual

Safety Information . . . . . . . .2–4  
Owner’s Manual  
& Installation  
Instructions  
Operating Instructions  
Care and Cleaning . . . . . . . .7–9  
Control Settings . . . . . . . . . . . .5  
Refrigerator Features . . . . . . . .6  
Replacing the Light Bulb . . . . .7  
2 Cubic Foot Models  
3 Cubic Foot Models  
4 Cubic Foot Models  
6 Cubic Foot Models  
Installation Instructions . .10–12  
Troubleshooting Tips . . . .13, 14  
Consumer Support  
Consumer Support . .Back Cover  
Warranty . . . . . . . . . . . . . . . . .15  
ATTENTION:  
Defrosting—Do not use sharp, pointed  
objects to remove frost or ice from  
surfaces of the refrigerator and/or  
freezer compartment. Doing so could  
puncture the cooling coil, causing the  
unit to lose its ability to maintain cold  
temperatures and voiding the warranty.  
See the Care and Cleaning section for  
instructions on defrosting the  
refrigerator and/or freezer  
compartment.  
Write the model and serial numbers here:  
Model # __________________________  
Serial # __________________________  
Find these numbers on a label inside  
the refrigerator on the side wall.  
197D5616P002 49-60327 03-04 JR  
Download from Www.Somanuals.com. All Manuals Search And Download.  
USE OF EXTENSION CORDS  
Because of potential safety hazards under certain conditions,  
we strongly recommend against the use of an extension cord.  
However, if you must use an extension cord, it is absolutely necessary  
that it be a UL-listed, 3-wire grounding type appliance extension cord  
having a grounding type plug and outlet and that the electrical rating  
of the cord be 15 amperes (minimum) and 120 volts.  
HOW TO CONNECT ELECTRICITY  
Do not, under any circumstances, cut or remove the third  
(ground) prong from the power cord. For personal safety,  
this appliance must be properly grounded.  
The power cord of this appliance  
is equipped with a 3-prong  
(grounding) plug which  
mates with a standard 3-prong  
(grounding) wall outlet to  
This provides the best  
performance and also prevents  
overloading house wiring circuits  
which could cause a fire hazard  
from overheated wires.  
minimize the possibility of electric  
shock hazard from this appliance.  
Never unplug your refrigerator  
by pulling on the power cord.  
Always grip plug firmly and pull  
straight out from the outlet.  
Have the wall outlet and circuit  
checked by a qualified electrician  
to make sure the outlet is  
properly grounded.  
Repair or replace immediately all  
power cords that have become  
frayed or otherwise damaged.  
Do not use a cord that shows  
cracks or abrasion damage along  
its length or at either end.  
If you have only a standard  
2-prong wall outlet, it is your  
personal responsibility and  
obligation to have it replaced  
with a properly grounded  
3-prong wall outlet.  
When moving the refrigerator  
away from the wall, be careful  
not to roll over or damage the  
power cord.  
The refrigerator should always be  
plugged into its own individual  
electrical outlet which has a  
voltage rating that matches the  
rating plate.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFETY INFORMATION.  
READ ALL INSTRUCTIONS BEFORE USING.  
WARNING!  
USE OF ADAPTER PLUGS  
Because of potential safety hazards under certain conditions,  
we strongly recommend against the use of an adapter plug.  
However, if you must use an  
adapter, where local codes  
permit, a temporary connection  
may be made to a properly  
grounded 2-prong wall outlet  
by use of a UL-listed adapter  
available at most local hardware  
stores.  
If the adapter ground terminal  
breaks, DO NOT USE the  
refrigerator until a proper  
ground has been established.  
Attaching the adapter ground terminal  
to a wall outlet cover screw does not  
ground the appliance unless the cover  
screw is metal, and not insulated, and  
the wall outlet is grounded through the  
house wiring. You should have the  
The larger slot in the adapter  
must be aligned with the larger  
slot in the wall outlet to provide  
circuit checked by a qualified electrician  
proper polarity in the connection to make sure the outlet is properly  
of the power cord.  
grounded.  
When disconnecting the power  
cord from the adapter, always  
hold the adapter in place with  
one hand while pulling the  
power cord plug with the other  
hand. If this is not done, the  
adapter ground terminal is very  
likely to break with repeated use.  
READ AND FOLLOW THIS SAFETY  
INFORMATION CAREFULLY.  
SAVE THESE INSTRUCTIONS  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
About the control  
on the refrigerator.  
The control will look like one of the above.  
Control Settings  
The temperature control maintains the temperature in the  
refrigerator. Setting the control at COOL is the warmest setting. Setting  
the control at COLDEST is the coldest setting. Set the control at COLD.  
Allow 24 hours for the refrigerator to reach the COLD temperature.  
If you want a colder or warmer temperature, move the dial one setting  
at a time. Moving the control to OFF stops cooling but does not turn  
off the power to the refrigerator. Setting the control to one of the  
snowflake positions may cause freezing in the refrigerator depending  
on the room temperature.  
How To Test Temperatures  
Use the milk test. Place a container of milk on a shelf and check it  
a day later. If the milk is too warm or too cold, adjust the temperature  
control.  
After changing the control, allow 24 hours for the refrigerator to reach the  
temperature you have set.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
About the refrigerator features.  
Shelves  
To remove a shelf, lift up the back slightly and pull forward.  
Some models have multi-position shelves that can be moved  
to different levels.  
Ice Tray Compartment (on some models)  
This compartment is designed for production of ice cubes and  
short-term storage (a few days at most) of some commercially-  
frozen foods when in contact with the evaporator (cold surface  
in compartment.)  
Door Shelves  
Shelves on the door provide convenient storage for frequently  
used items. Some models have doors that are deep enough to  
store large bottles.  
Key-Ejecting Lock (on some models)  
The key for the spring-loaded lock is automatically ejected—  
key will not remain in lock in either the open or closed position.  
Keep the key out of reach of children and away from the refrigerator.  
If a replacement key is needed, it can be ordered by visiting our  
Website www.GEAppliances.com, or calling GE Parts and Accessories,  
800.626.2002.  
Refrigerator Storage Zones (on cycle defrost all-refrigerator models)  
REFRIGERATOR STORAGE ZONES  
BEST FOR FRUITS, VEGETABLES  
For best results follow  
the recommended  
storage zones:  
FRUIT  
ZONE  
I The top and (front)  
middle shelf are best  
Top Shelf  
for storing fruits and  
vegetables.  
Case  
Back  
Middle Shelf  
Door  
(Front)  
I The (rear) middle  
shelf and bottom shelf  
are best for storing  
beverages, deli meats  
and cheeses.  
DELI  
ZONE  
Bottom Shelf  
BEST FOR BEVERAGES, DELI  
MEATS, AND CHEESES  
Side View of Refrigerator  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
Care and cleaning  
of the refrigerator.  
Cleaning the Outside  
Keep the outside clean. Wipe with a clean cloth lightly dampened  
with kitchen appliance wax or mild liquid dish detergent. Dry and  
polish with a clean, soft cloth.  
Do not wipe the refrigerator with a soiled dish cloth or wet towel. These may  
leave a residue that can erode the paint. Do not use scouring pads, powdered  
cleaners, bleach or cleaners containing bleach because these products can  
scratch and weaken the paint finish.  
Protect the paint finish. The finish on the outside of the refrigerator  
is a high quality, baked-on paint finish. With proper care, it will  
stay new-looking and rust-free for years. Apply a coat of kitchen/  
appliance wax when the refrigerator is new, and then at least  
twice a year.  
Cleaning the Inside  
To help prevent odors, leave an open box of baking soda in the  
refrigerator.  
Unplug the refrigerator before cleaning. If this is not practical,  
wring excess moisture out of sponge or cloth when cleaning  
around the control.  
Use warm water and baking soda solution–about a tablespoon  
(15 ml) of baking soda to a quart (1 liter) of water. This both  
cleans and neutralizes odors. Rinse and wipe dry.  
Other parts of the refrigerator–including door gaskets, fruit  
and vegetable drawers, and all plastic parts–can be cleaned  
the same way.  
Do not wash any plastic refrigerator parts in the dishwasher.  
Replacing the Light Bulb (on some models)  
Unplug the refrigerator before replacing a burned-out bulb.  
Setting the controls to OFF does not remove power to the  
light circuit.  
The light bulb is located behind the temperature control housing  
and is visible through the slots in the housing.  
Reach up through the opening at the bottom of the control  
housing and gently unscrew the light bulb. Replace with a bulb  
of the same or lower wattage.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Care and cleaning of the refrigerator.  
Defrosting (on manual defrost models with freezer area)  
Defrost whenever frost on the wall of the ice tray compartment becomes  
1/4thick. Never use a sharp or metallic instrument to remove frost as  
it may damage the cooling coils. (A punctured cooling coil will cause  
serious problems and void the warranty.) We recommend using a plastic scraper.  
Do not use any electrical device in defrosting your refrigerator.  
To defrost:  
I Remove foods and ice trays from the ice tray compartment.  
I Set the temperature control dial at OFF position.  
I On models without a drip tray, place a pan beneath the ice tray  
compartment to collect water.  
Defrosting usually takes a few hours. To defrost faster, keep the  
door open. Also, pouring warm (not hot) water on the frosted part  
may speed defrosting. Do not use boiling water—it may damage  
plastic parts.  
After defrosting:  
I Empty water from the drip tray or from the pan placed beneath  
the ice tray compartment. Wash the tray or pan with warm water.  
I Wipe the ice tray compartment with a damp cloth.  
I Turn the temperature control to the desired setting and  
return food and ice trays to the refrigerator.  
NOTE: If ice buildup is very thick, it may keep the ice tray compartment door  
from opening or closing completely. Don’t try to force it open; after defrosting,  
the door will open and close easily.  
Defrosting (on cycle defrost all-refrigerator models)  
Defrost whenever frost on the inside surfaces of the storage area becomes 1/8″  
(3 mm) thick. Never use a heater of any kind, scraper or sharp metallic  
instrument to remove frost as it may damage the refrigerator or cooling  
coils. ( A punctured cooling coil will cause serious problems and void  
the warranty.)  
To defrost, unplug the refrigerator or turn the temperature control  
dial to the OFF position. Remove the contents and wipe inside  
surfaces and shelves with a clean towel. If frost does not come off  
easily, allow the frost to melt somewhat and wipe off.  
After defrosting, make sure inside surfaces are dry; then return the  
contents to the refrigerator, plug unit back in and set the  
temperature control to the desired setting.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Care and cleaning  
of the refrigerator.  
Preparing for Vacation  
For long vacations or absences, remove food and unplug the  
refrigerator. Move the control to the OFF position, and clean the  
interior with a baking soda solution of one tablespoon (15 ml) of  
baking soda to one quart (1 liter) of water. Leave the door open.  
Preparing to Move  
Secure all loose items such as shelves and ice trays by taping them  
securely in place to prevent damage.  
Be sure the refrigerator stays in an upright position during moving.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preparing to install the refrigerator.  
Read these instructions completely and carefully.  
Refrigerator Location  
I Do not install the refrigerator where the temperature will go below  
50°F (10°C) because it will not run often enough to maintain  
proper temperatures.  
I Install it on a floor strong enough to support it fully loaded.  
I If the 2 cubic foot model is placed on a countertop or stand,  
the front surface of the door should be 3or more back from the  
edge of the countertop or stand to avoid accidental tipping of the  
appliance during normal use.  
I Do not install it closer than 5(13 cm) next to a range.  
The following applies only to the 2, 3 and 4 Cubic Foot Models:  
I Do not install it in a recessed area.  
I Do not build in the refrigerator.  
Clearances  
Allow the following clearances for ease of installation and proper  
air circulation.  
2, 3 and 4  
Cubic Foot Models  
6 Cubic Foot  
Model only  
Sides  
Top  
1/2″ (13 mm)  
2(51 mm)  
0″ (0 mm)∗  
0″ (0 mm)  
0″ (0 mm)  
Back  
2(51 mm)**  
*1-1/4(32 mm) for hinge side clearance  
**From the rear cabinet surface to the wall  
Leveling Legs (on some models)  
Adjustable legs at the front corners of the refrigerator  
should be set so the refrigerator is firmly positioned on  
the floor and the front is raised just enough that the  
door closes easily when opened about halfway.  
To adjust the leveling legs, turn the legs counterclockwise  
to raise the refrigerator, clockwise to lower it.  
Turn counterclockwise to raise,  
clockwise to lower.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preparing to install the refrigerator.  
Door Reversal (on some models)  
Hinge cover  
Plug buttons  
or screws  
1. Remove the small plug button on the  
left side of the door top cap.  
Hinge  
2. Remove the three plug buttons or  
screws on the left side on top of the  
cabinet.  
Plug button  
3. Remove the plastic hinge cover by  
lifting it up by the front edge.  
4. Remove the three screws from the  
top hinge.  
5. Lift the door up and off the bottom  
hinge (right side).  
6. Tilt the refrigerator cabinet back to  
remove the right leveling leg.  
7. Remove the screws on the bottom  
hinge (right side) and the left leveling  
leg. Move the bottom hinge to the left  
side and secure it with the screws and  
leveling leg.  
Bottom  
hinge  
Spacer  
Leveling legs  
IMPORTANT: The left leg has a spacer that  
must be moved to the right side leveling leg  
when the door swing is reversed.  
8. Screw the right leveling leg, with the  
spacer in place, back in place on the  
right side.  
9. Position the door on the left bottom  
hinge. With the magnetic gasket  
holding the door in place, secure the  
top hinge with screws.  
10. Make sure the door is aligned with the  
refrigerator cabinet before continuing.  
11. Replace the hinge cover on top of  
the hinge.  
12. Put the plug button in the hole on the  
right side of the door cap.  
13. Put the three plug buttons or screws on  
the right side on top of the cabinet.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preparing to install the refrigerator.  
Door Reversal (on some models)  
4 Cubic Foot Models  
1. Remove the two screws at the back of  
the top cover.  
Upper  
hinge  
Top cover  
Left hinge location  
2. Remove the top cover by lifting the back  
up about 2and then sliding it forward.  
Top  
plate  
3. Remove the small plug button on the  
left side of the door top cap.  
Plug button  
4. Remove the three screws on the upper  
hinge (right side). Remove the hinge.  
Door  
top cap  
5. Remove the three screws at the left  
hinge location on the top plate.  
6. Remove the screw in the middle of the  
top plate and remove the top plate.  
7. Lift the door up and off the bottom  
hinge (right side).  
8. Tilt the refrigerator cabinet back to  
remove the right leveling leg.  
Bottom  
hinge  
9. Remove the screws on the bottom  
hinge (right side) and the left leveling  
leg. Move the bottom hinge to the left  
side and secure it with the screws and  
leveling leg.  
Spacer  
Leveling legs  
IMPORTANT: The left leg has a spacer that  
must be moved to the right side leveling leg  
when the door swing is reversed.  
10. Screw the right leveling leg, with the  
spacer in place, back in place on the  
right side.  
11. Position the door on the left bottom  
hinge. With the magnetic gasket  
holding the door in place, secure the  
top hinge with screws.  
12. Make sure the door is aligned with the  
refrigerator cabinet before continuing.  
13. Replace the top plate and screws.  
14. Slide the top cover back in place and  
replace the two screws.  
15. Put the plug button in the hole on the  
right side of the door top cap.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting tips.  
Save time and money!  
Problem  
Possible Causes  
What To Do  
Refrigerator does not  
operate  
Control in OFF position.  
Move the control to a  
temperature setting.  
Refrigerator is  
unplugged.  
Push the plug completely  
into the outlet.  
The fuse is blown/circuit Replace fuse or reset  
breaker is tripped.  
the breaker.  
Vibration or rattling  
(slight vibration  
is normal)  
Front leveling legs  
(on some models)  
need adjusting.  
See Leveling Legs.  
Refrigerator is on  
an uneven surface.  
Use shims to level the  
refrigerator.  
Motor operates for  
long periods or cycles  
Normal when refrigerator Wait 24 hours for the  
is first plugged in.  
refrigerator to completely  
cool down.  
Often occurs when  
This is normal.  
large amounts of food  
are placed in refrigerator.  
Door left open.  
Check to see if package is  
holding door open.  
Hot weather or frequent  
door openings.  
This is normal.  
Temperature control  
set at the coldest setting.  
See About the control.  
Not enough clearance  
from the wall.  
See Clearances in Preparing  
to install the refrigerator.  
Door will not open  
Refrigerator is locked  
(lock is available  
on some models).  
Unlock the door with  
the key. If the key has  
been lost, a replacement  
key can be ordered by  
visiting our Website  
or calling GE Parts and  
Accessories, 800.626.2002.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting tips.  
Save time and money!  
Problem  
Possible Causes  
What To Do  
Refrigerator too warm  
Temperature control  
not set cold enough.  
See About the control.  
Warm weather or  
frequent door openings.  
Set the temperature  
control one step colder.  
See About the control.  
Door left open.  
Check to see if package is  
holding door open.  
Cabinet sides are warm  
(applies only to 2, 3 and  
4 Cubic Foot Models).  
This is normal for a hot  
wall type condenser.  
Refrigerator has odor  
Foods transmitting odor  
to refrigerator.  
Foods with strong odors  
should be tightly wrapped.  
Keep an open box of  
baking soda in the  
refrigerator; replace  
every three months.  
Interior needs cleaning.  
See Care and cleaning.  
See Care and cleaning.  
Defrost water pan needs  
cleaning (on some models).  
Moisture forms on  
outside of refrigerator  
Not unusual during  
periods of high humidity.  
Wipe surface dry.  
Moisture collects inside  
(in humid weather,  
air carries moisture  
into refrigerator when  
door is opened)  
Too frequent or too long  
door openings.  
Refrigerator too cold  
Temperature control  
set too cold.  
See About the control.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GE Refrigerator  
One-Year Limited Warranty.  
Staple your receipt here.  
Proof of the original purchase date is  
needed to make a warranty claim.  
For The Period Of:  
What GE Will Provide:  
One Year  
From the date of the  
original purchase  
Replacement unit for any product which fails due to a  
defect in materials or workmanship. The exchange  
unit is warranted for the remainder of your product’s  
original one-year warranty period.  
In Order to Make a Warranty Claim:  
I Properly pack your unit.  
We recommend using the original  
carton and packing materials.  
I Include in the package a copy of  
the sales receipt or other evidence  
of date of original purchase. Also  
print your name and address and  
a description of the defect.  
I Return the product to the retail  
location where it was purchased.  
What GE Will Not Cover:  
I Customer instruction. This owner’s  
manual provides information  
regarding operating instructions  
and user controls.  
I Loss of food due to spoilage.  
I Replacement of house fuses or  
resetting of circuit breakers.  
I Replacement of the light bulbs.  
I Damage caused after delivery.  
I Service trips to your home to teach  
you how to use the product.  
I Damage to the product caused by  
accident, fire, floods or acts of God.  
I Improper installation, delivery or  
maintenance.  
I Incidental or consequential damage  
caused by possible defects with  
this appliance.  
I Failure of the product if it  
is abused, misused, or used for  
other than the intended purpose  
or used commercially.  
This warranty is extended to the original purchaser and any succeeding owner for  
products purchased for home use within the USA.  
Some states do not allow the exclusion or limitation of incidental or consequential  
damages. This warranty gives you specific legal rights, and you may also have other  
rights which vary from state to state. To know what your legal rights are, consult your  
local or state consumer affairs office or your state’s Attorney General.  
Exclusion of implied warranties: Except where prohibited or restricted by law,  
there are no warranties, whether express, oral or statutory which extend beyond  
the description on the face hereof, including specifically the implied warranties  
of merchantability or fitness for a particular purpose.  
15  
Warrantor: General Electric Company. Louisville, KY 40225  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Consumer Support.  
GE Appliances Website  
Have a question or need assistance with your appliance? Try the GE Appliances Website  
24 hours a day, any day of the year! For greater convenience and faster service, you can  
now download Owner’s Manuals, order parts or order catalogs on-line. You can also  
“Ask Our Team of Experts” your questions, and so much more...  
Real Life Design Studio  
GE supports the Universal Design concept–products, services and environments that  
can be used by people of all ages, sizes and capabilities. We recognize the need to  
design for a wide range of physical and mental abilities and impairments. For details  
of GE’s Universal Design applications, including kitchen design ideas for people with  
disabilities, check out our Website today. For the hearing impaired, please call  
800.TDD.GEAC (800.833.4322).  
Parts and Accessories  
Individuals qualified to service their own appliances can have parts or accessories  
sent directly to their homes (VISA, MasterCard and Discover cards are accepted).  
Order on-line today, 24 hours every day or by phone at 800.626.2002 during normal  
business hours.  
Instructions contained in this manual cover procedures to be performed by any user.  
GE does not support any servicing of the refrigerator.  
Contact Us  
If you are not satisfied with the service you receive on your GE product, contact us  
on our Website with all the details including your phone number, or write to:  
General Manager, Customer Relations  
GE Appliances, Appliance Park  
Louisville, KY 40225  
Printed in China  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Echo Brush Cutter SRM 410U User Manual
Eizo Computer Monitor R12 User Manual
Euro Pro Carpet Cleaner SC926H User Manual
Fujitsu Printer FTP 629MCL103 R User Manual
Furuno Marine RADAR FR FAR 2835SW 2865SW User Manual
Gaggenau Fryer VF 230 User Manual
Gaggenau Oven ED221 User Manual
Galil Home Security System DMC 1700 User Manual
Geemarc Stereo Amplifier CLA 40 VOX User Manual
Global Upholstery Co Computer Hardware 3307568 User Manual