Echo Brush Cutter SRM 410U User Manual

Grass Trimmer/Brush Cutter  
Operator's Manual  
MODEL  
SRM-410U  
WARNING  
Users of this equipment risk injury to themselves and others if the unit is used im-  
properly and/or safety precautions are not followed. ECHO provides an operator’s  
manual and a safety manual. Both must be read and understood for proper and safe  
operation. Failure to do so could result in serious injury.  
X750-012 31 6  
X750 216-3706  
Printed in Japan 1401Ek 1114 ES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GRASS TRIMMER/BRUSH CUTTER  
OPERATOR'S MANUAL  
3
SAFETY  
MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION  
Throughout this manual and on the product itself, you will nd safety alerts and helpful, informational messages pre-  
ceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean  
to you.  
CIRCLE AND SLASH SYMBOL  
This symbol means the specic action  
shown is prohibited. Ignoring these prohi-  
bitions can result in serious or fatal injury.  
DANGER  
The safety alert symbol accompanied by the word  
“DANGER” calls attention to an act or condition  
which WILL lead to serious personal injury or  
death if not avoided.  
NOTE  
WARNING  
This enclosed message provides tips for use, care and  
maintenance of the unit.  
The safety alert symbol accompanied by the word  
WARNING” calls attention to an act or condi-  
tion which CAN lead to serious personal injury or  
death if not avoided.  
IMPORTANT  
The enclosed message provides information neces-  
sary for the protection of the unit.  
CAUTION  
The safety alert symbol accompanied by the word  
“CAUTION” calls attention to an act or condition  
which may lead to minor or moderate personal  
injury if not avoided.  
INTERNATIONAL SYMBOLS  
SYMBOL  
SYMBOL  
SYMBOL  
SYMBOL  
DESCRIPTION  
DESCRIPTION  
DESCRIPTION  
DESCRIPTION  
"WARNING, SEE OP-  
ERATOR'S MANUAL  
Emergency  
Stop  
Hot  
Surface  
Fuel and oil  
mixture  
Carburetor Adjust-  
ment  
- High speed  
mixture  
Wear eye, ear  
and head protec-  
tion  
Primer  
Bulb  
Finger Severing  
Carburetor Adjust-  
ment  
- Idle speed  
DO NOT allow  
ames or sparks  
near fuel.  
Ignition  
ON/  
OFF  
Wear hand and  
foot protection  
Carburetor Adjust-  
ment  
- Low speed  
mixture  
Do not use  
blades. String  
line only  
DO NOT smoke  
near fuel.  
Safety/Alert  
Choke Control  
"Run"  
Position  
Choke Control  
"Cold Start"  
Position  
Keep bystanders and helpers  
away 15 m (50 ft.).  
(Choke Open)  
(Choke Closed)  
PERSONAL CONDITION AND SAFETY EQUIPMENT  
WARNING  
Users of this product risk injury to themselves and others if the unit is used improperly and/or safety precautions  
are not followed. Proper clothing and safety gear must be worn when operating unit.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Physical Condition  
Your judgment and physical dexterity may not be good:  
• if you are tired or sick,  
• if you are taking medication,  
• if you have taken alcohol or drugs.  
Operate unit only if you are physically and mentally well.  
Eye Protection  
Wear eye protection that meets ANSI Z87.1 or CE requirements whenever you operate the unit.  
Hand Protection  
Wear no-slip, heavy-duty work gloves to improve your grip on the handle. Gloves also reduce the transmission of ma-  
chine vibration to your hands.  
Hearing Protection  
ECHO recommends wearing hearing protection whenever unit is used.  
Proper Clothing  
Wear snug tting, durable clothing;  
• Pants should have long legs, shirts with long sleeves.  
• DO NOT WEAR SHORTS,  
• DO NOT WEAR TIES, SCARFS, JEWELRY.  
Wear protective hair covering to contain long hair.  
Wear sturdy work shoes with nonskid soles;  
• DO NOT WEAR OPEN TOED SHOES,  
• DO NOT OPERATE UNIT BAREFOOTED.  
Keep long hair away from engine and air intake. Retain hair with cap or net.  
Hot Humid Weather  
Heavy protective clothing can increase operator fatigue which may lead to heat stroke. Schedule heavy work for early  
morning or late afternoon hours when temperatures are cooler.  
Extended Operation/Extreme Conditions  
It is believed that a condition called Raynaud’s Phenomenon, which affects the ngers of certain individuals, may be  
brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sensa-  
tions, followed by loss of color and numbness in the ngers. The following precautions are strongly recommended,  
because the minimum exposure, which might trigger the ailment, is unknown.  
• Keep your body warm, especially the head, neck, feet, ankles, hands,  
and wrists.  
• Maintain good blood circulation by performing vigorous arm exer-  
cises during frequent work breaks, and also by not smoking.  
• Limit the hours of operation. Try to ll each day with jobs where op-  
erating the unit or other hand-held power equipment is not required.  
• If you experience discomfort, redness, and swelling of the ngers fol-  
lowed by whitening and loss of feeling, consult your physician before  
further exposing yourself to cold and vibration.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GRASS TRIMMER/BRUSH CUTTER  
OPERATOR'S MANUAL  
5
Repetitive Stress Injuries  
It is believed that overusing the muscles and tendons of the ngers, hands, arms, and shoulders may cause soreness,  
swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high  
risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which  
could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged  
exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years.  
To reduce the risk of RSI/CTS, do the following:  
• Avoid using your wrist in a bent, extended, or twisted position.  
Instead try to maintain a straight wrist position. Also, when grasping,  
use your whole hand, not just the thumb and index nger.  
• Take periodic breaks to minimize repetition and rest your hands.  
• Reduce the speed and force with which you do the repetitive move-  
ment.  
• Do exercise to strengthen the hand and arm muscles.  
• Immediately stop using all power equipment and consult a doctor if  
you feel tingling, numbness, or pain in the ngers, hands, wrists, or  
arms. The sooner RSI/CTS is diagnosed, the more likely permanent  
nerve and muscle damage can be prevented.  
DANGER  
Do not operate this product indoors or in inadequately ventilated  
areas. Engine exhaust contains poisonous emissions and can cause  
serious injury or death.  
Read the Manuals  
• Provide all users of this equipment with the Operator’s Manual and  
Safety Manual for instructions on Safe Operation.  
Clear the Work Area  
• Spectators and fellow workers must be warned, and children and  
animals prevented from coming nearer than 15 m (50 ft.) while the  
unit is in use.  
Keep a Firm Grip  
• Always use both hands on the handles. Do not operate one-handed.  
Always hold the unit with the ngers and thumbs encircling the  
handles.  
Keep a Solid Stance  
• Maintain footing and balance at all times. Do not stand on slippery,  
uneven or unstable surfaces. Do not work in odd positions or on lad-  
ders. Do not over reach.  
Avoid Hot Surfaces  
• Keep exhaust area clear of ammable debris. Avoid contact during  
and immediately after operation.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
EQUIPMENT  
WARNING  
Use only ECHO approved attachments. Serious injury may result from the use of a non-approved attachment com-  
bination. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which  
have not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and  
safety manual.  
• Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed.  
• Inspect shield for damage and ensure that the cut-off knife is securely in place. Replace if either is damaged or miss-  
ing.  
• Check that the cutting attachment is rmly attached and in safe operating condition.  
• Check that front loop handle and shoulder strap/ or shoulder/waist harness are adjusted for safe, comfortable opera-  
tion. See Assembly Section for proper adjustment.  
WARNING  
Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all  
openings.  
ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop  
before removing obstructions, clearing debris, or servicing unit.  
DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.  
NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings.  
WARNING  
Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage or leaks are found,  
do not use unit, otherwise serious personal injury or property damage may occur. Have unit repaired by an authorized  
servicing dealer before using.  
EMISSION CONTROL (EXHAUST & EVAPORATIVE)  
EPA 2010 and Later and/or C.A.R.B. TIER III  
e emission control system for the engine is EM (engine  
modification) and, if the second to last character of the Engine  
Family on the Emission Control Information label (sample  
below) is “C, K, or “T, the emission control system is EM  
and TWC (3-way catalyst). e fuel tank/fuel line emission  
control system is EVAP (evaporative emissions). Evaporative  
emissions for California models may only be applicable to fuel  
tanks.  
An Emission Control Label is located on the engine. (is  
is an EXAMPLE ONLY, information on label varies by  
engine FAMILY).  
PRODUCT EMISSION DURABILITY (EMISSION COMPLIANCE PERIOD)  
e 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emis-  
sions output meets applicable emissions regulations, provided that approved maintenance procedures are followed as  
listed in the Maintenance Section of this manual.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GRASS TRIMMER/BRUSH CUTTER  
OPERATOR'S MANUAL  
7
DESCRIPTION  
Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the instruc-  
tions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING  
instructions for specic information.  
9
Hot Decal (near mufer)  
P/N X505002310  
4
5
3
2
10  
6
1
8
20  
12  
7
11  
13  
19  
18  
17  
14  
Shaft Decal  
15  
16  
P/N 89031749030  
Metal Debris Shield Decal  
P/N 89011841031  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter.  
2. THROTTLE TRIGGER LOCKOUT - This lever must be held during starting. Operation of the throttle trigger is  
prevented unless throttle trigger lockout lever is engaged.  
3. STOP SWITCH - "SLIDE SWITCH" mounted on top of the Throttle Trigger Housing. Move switch FORWARD  
to RUN, BACK to STOP.  
4. THROTTLE TRIGGER - Controls engine speed. Spring loaded to return to idle when released. During accelera-  
tion, press trigger gradually for best operating technique.  
5. DRIVE SHAFT ASSEMBLY - Includes the Gear Housing assembly, metal drive shaft and Safety Decal.  
6. U-HANDLE - Required for metal blade operation.  
7. HIP PAD - Used to protect hip/leg and clothing when using U-handle equipped unit.  
8. SHOULDER HARNESS- An adjustable strap that suspends the unit from the operator. Using the strap reduces  
operator fatigue.  
9. BLADE - Circular blade for grass, weed or brush cutting applications. Harness, metal shield & U-handles required  
for blade operation.  
10. METAL BLADE SHIELD - Required when unit is equipped with blades. Do not operate unit without shield.  
11. SPARK PLUG - Provides spark to ignite fuel mixture.  
12. ARM REST - Provides arm rest during operation and protects arm from the hot engine.  
13. SPARK ARRESTOR MUFFLER OR SPARK ARRESTOR MUFFLER WITH CATALYST -The mufer or  
catalytic mufer controls exhaust noise and emission. The spark arrestor screen prevents hot, glowing particles of  
carbon from leaving the mufer. Keep exhaust area clear of ammable debris.  
14. FUEL TANK - Contains fuel and fuel lter.  
15. RECOIL STARTER HANDLE - Pull handle slowly until starter engages, then quickly and rmly. When engine  
starts, return handle slowly. DO NOT let handle snap back or damage to unit will occur.  
16. FUEL TANK CAP - Covers and seals fuel tank opening.  
17. PURGE BULB - Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging air from  
the carburetor. Pump purge bulb until fuel is visible and ows freely in the clear fuel tank return line. Pump purge  
bulb an additional 4 or 5 times.  
18. AIR CLEANER - Contains replaceable lter element.  
19. CHOKE - The choke control is located at the rear of the air cleaner housing. Move choke lever to Cold Start  
(
) to close choke for cold start. Move choke lever to "Run" (  
) position to open choke.  
20. DECOMPRESSION BUTTON - Push button to assist starting. Automatically resets after engine starts and runs.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GRASS TRIMMER/BRUSH CUTTER  
OPERATOR'S MANUAL  
9
CONTENTS  
The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions,  
shield installation and other assembly may be necessary.  
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing  
parts. Use the contents list to check for missing parts.  
___ 1-Power Head  
___ 1- Drive Shaft Assembly  
___ 1- Plastic Bag (co-pack)  
__ - 1, Operator's Manual  
__ - 1, Safety Manual  
__ - 1, Warranty Registration Card  
___ - 1, Tool Bag  
___  
___  
___  
___  
--1, wrench 17x19 mm  
--1, locking tool  
--1, 8 x 10 mm Open End Wrench  
--1, 4 mm Hexagon Wrench  
___ - 1, Safety Glasses  
___ - 1, Plastic Bag  
___  
___  
___  
___  
___  
--3, 5 mm x 10 mm screws (shield mount)  
--2, 5 mm x 10 mm screws (bracket to shield)  
--4, 5 mm nuts  
--1, metal shield  
--1, bracket  
___ - 1, Shoulder Harness w/hip pad  
___ - 10, Cotter Pins  
____ - 1, Blade  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
ASSEMBLY  
DRIVE SHAFT/POWER HEAD  
Tools Required: 4 mm Hex Wrench  
Parts Required: Power Head, Drive Shaft Assembly  
1. Stand power head upright on a level surface.  
2. Loosen the drive shaft clamp bolt (A) at engine drive shaft clamp,  
and remove drive shaft locating bolt (B).  
B
3. Remove protective plastic cap from end of drive shaft assembly.  
Carefully t driveshaft assembly to engine making sure that  
inner drive shaft engages clutch mount.  
4. Turn drive shaft housing until locating hole lines up with locating  
hole in clamp and install drive shaft locating bolt (B).  
A
NOTE  
Gear housing must be aligned properly with engine. Aligning center  
locating hole in driveshaft housing with center drive shaft bolt (B)  
provides correct alignment.  
5. Tighten drive shaft clamp bolt (A) securely.  
WARNING  
Never start engine without driveshaft assembly installed.  
This could result in serious injury.  
BLADE INSTALLATION  
WARNING  
You must install the U-Handle and all Blade Conversion parts shown in the following instructions before operating  
this unit with a metal blade, otherwise serious injury may result.  
Install Metal Shield  
Tools Required: 8 x 10 mm Open-end Wrench, Screwdriver, 17x19 mm Wrench, Locking Tool  
Parts Required: Metal Shield, Shield Bracket,  
3 - 5 x 10 mm screws (metal shield to gear housing).  
2 - 5 x 10 mm screws, 2 - 5 mm nuts (bracket to shield).  
2 - 5 mm nuts (bracket to gear housing).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GRASS TRIMMER/BRUSH CUTTER  
OPERATOR'S MANUAL  
11  
1. Align hole in upper plate (D) with notch in gear housing (E), and  
E
insert locking tool to prevent splined shaft from turning. Arrow on  
gear housing ange points to notch location.  
2. Remove split pin (F), L.H. blade nut (G), lower plate (H), and up-  
per plate (D) from PTO shaft. Turn blade nut clockwise to remove.  
D
3. Remove locking tool.  
H
G
F
E
4. Loosely attach bracket (I) to shield (J) and attach shield to bottom  
of gear housing (E) with hardware provided.  
5. Tighten all shield hardware.  
J
Install Blade  
Tools Required: Locking Tool, 17x19 mm Wrench.  
Parts Required: Upper Plat, Lower Plate, 10 mm Nut w/L.H. threads,  
2 x 25 mm Cotter Pin, Blade.  
D
K
1. Install upper plate (D) on splined PTO shaft, pilot side down.  
Blade installation requires Upper Plate (D).  
L
2. Install Blade (K) on upper plate pilot. Blades must be installed so  
that rotation arrow on blade matches rotation of unit: teeth toward  
direction of rotation (See debris shield decal). Secure blade with  
Lower Plate (H), and 10 mm L.H. nut (G). Turn nut counter-clock-  
wise on PTO shaft to tighten.  
H
G
3. Align hole in upper plate with notch in gear housing, and insert  
Locking Tool (L) to prevent splined shaft from turning. Arrow on  
gear housing points to notch. Tighten 10 mm nut securely.  
F
4. Insert Cotter Pin (F) in hole in PTO shaft, and bend pin legs around  
shaft counterclockwise to retain 10 mm nut.  
L
D
20  
IMPORTANT  
Never reuse a cotter pin - install a new cotter pin each time a blade  
is installed or replaced.  
K
H
5. Remove locking tool.  
G
F
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
U-HANDLE INSTALLATION  
Tools Required: 17 & 19 mm wrench, 4 mm hex socket wrench  
A
Parts Required: U-Handle, Clamp w/screws  
1. Remove assembling bolt (A) from right hand grip. Install right  
hand grip (B) onto right hand U-handle (C) until bolt hole in U-  
handle is visible through bolt hole in bottom of grip. Grip should  
not rotate on handle.  
B
2. Install assembling bolt to secure grip onto U-handle.  
C
3. Remove bolt retainer tube (D) from end of handle assembling bolt  
(E).  
E
D
4. Install handle assembling bracket (upper) (F) in handle assembling  
bracket (lower) (G) and secure handle by tightening handle assem-  
bling bolt (E) loosely.  
F
E
G
5. Loosen 4 right handle assembling bolts (H) and insert right hand  
U-handle (C) into right handle assembling bracket (I). (toward  
H
I
direction of arrow  
).  
C
Download from Www.Somanuals.com. All Manuals Search And Download.  
GRASS TRIMMER/BRUSH CUTTER  
OPERATOR'S MANUAL  
13  
6. Secure the right hand U-handle by tightening 4 right handle assem-  
bling bolts (H) loosely.  
H
E
7. Adjust handles for comfortable operation and tighten handle as-  
sembling bolt (E) and 4 right handle assembling bolts (H).  
8. Route throttle linkage and ignition lead assembly along shaft and  
clip as shown.  
BALANCE AND ADJUST UNIT  
1. Loosen harness clamp screw.  
2. Put on harness and attach unit to harness.  
3. Slide harness clamp up (A) or down until unit balances with head  
approximately 50-75 mm (2 -3 in.) from the ground.  
B
4. Tighten harness clamp screw.  
5. Loosen upper U-Handle clamp screws (B), and position U-Handle  
for comfortable operation.  
A
6. Tighten U-Handle clamp screws and 8 mm clamp bolt securely.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
OPTIONAL NYLON HEAD INSTALLATION  
Tools Required: Locking Tool  
Parts Required: Nylon Line Head.  
1. Align hole in upper plate with notch in gear housing, and insert  
locking tool to prevent splined shaft from turning.  
2. Thread line head onto PTO shaft by turning it counter-clockwise  
until head is tight against upper plate.  
3. Remove locking tool.  
• Read the Operator’s Manual carefully. Be thoroughly familiar  
with the controls and proper use of the trimmer.  
Know how to stop the unit and disengage the controls.  
• Never allow children to operate the trimmer.  
• Never allow adults to use the trimmer unless they have received  
proper instructions. Be sure the operator is properly attired and  
wears the type of foot, leg, head, eye and ear protection recom-  
mended both in your ECHO Operator’s Manual and by your  
ECHO Servicing Dealer.  
• Always wear eye protection that conforms to ANSI Z 87.  
1-2000.1. Read the Operator’s Manual carefully. Be thoroughly  
familiar with the controls and proper use of the trimmer.  
Know how to stop the unit and disengage the controls.  
WARNING  
Grass/weed trimmers can throw gravel, stone, wood chips, glass,  
and plastic or metal objects. The debris shield behind the trimmer  
head stops much of the debris, but cannot prevent the operator from  
being struck by some debris. Read the rules for safe operation in  
the operator’s manual that you received with your ECHO trimmer.  
Also, follow all instructions in this instruction sheet.  
1. REPLACING LINE  
A. Remove spool by turning knob clockwise, “right”, and separating  
parts.  
15 cm  
B. Thread a 6 m (20 feet) length of 2.4 mm (0.095 in) or 2.7 mm  
(0.105 in) ECHO line through hole in spool so that ends are the  
same length.  
C. Wind both ends of line tightly and evenly clockwise (see arrows on  
spool), and wind from side to side without twisting the lines.  
D. Secure ends of line temporarily with about 15 cm (6 in) extending  
out.  
spool  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GRASS TRIMMER/BRUSH CUTTER  
OPERATOR'S MANUAL  
15  
2.REPLACING SPOOL  
Housing  
NOTE  
Keep line tight on spool.  
Bolt  
A. Snap spool into housing while pulling line through eyelets with  
about 15 cm (6 in) extending out.  
CAUTION  
Knob tightens counterclockwise, “left”.  
Spring  
Knob  
B. Fasten spool to housing with shaft bolt, spring, and knob.  
OPERATING INSTRUCTIONS NYLON LINE  
1. Always use the end of the line for cutting. Forcing the cutter head  
too close to the work will result in reduced efciency and broken  
line.  
2. Maintain the line at the recommended length of 12.5 to 15 cm (5  
to 6 in). A longer line will reduce engine speed, a shorter line may  
result in engine damage.  
3. The trimmer head rotates counterclockwise. Always cut with the  
head tilted to the right to deect debris away from the operator.  
4. Always observe the SAFETY RULES on Page 3 when using the  
unit.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16  
OPERATION  
WARNING  
Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all  
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete  
stop before removing obstructions, clearing debris, or servicing unit.  
WARNING  
Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause unconscious-  
ness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position unit so that exhaust is directed  
away from your face and body.  
WARNING  
Operation of this equipment may create sparks that can start fires. is unit is equipped with a spark arrestor to  
prevent discharge of hot particles from the engine. Metal blade use also can create sparks if the blade strikes rocks,  
metal, or other hard objects. Contact local fire authorities for laws or regulations regarding fire prevention require-  
ments.  
BLADE SELECTION  
WARNING  
The type of Blade used MUST be matched to the type and size of material cut. An improper or dull blade can cause  
serious personal injury. Blades MUST be sharp. Dull blades increase the chance of kick-out and injury to yourself  
and bystanders.  
BLADE SET-UP GUIDE  
Pro Maxi-Cut  
Grass/Weed  
Blade  
Rigid Plastic  
Tri-Cut  
Grass/Weed Blade  
Metal Blade  
TO USE  
THESE BLADES  
U-Handle or Loop  
Handle  
w/Barrier Bar  
Loop Handle, w/or  
w/o Barrier Bar  
U-Handle or Loop Handle  
w/Barrier Bar  
Plastic Shield  
Harness  
Plastic Shield  
Harness  
Metal Shield  
Harness  
You  
must  
install  
these  
parts!  
Upper Plate &  
Flat Washer  
Upper Plate  
& Glide Cup  
Upper/Lower  
Blade Plates  
Hex Nut  
Hex Nut  
Hex Nut  
New Cotter Pin  
New Cotter Pin  
New Cotter Pin  
WARNING! DO NOT INSTALL BLADES ON GT (CURVED SHAFT) MODEL TRIMMERS  
• Arbor diameter of Upper Blade Plate must match arbor diameter of blades.  
• New cotter pin required each time blade is installed.  
• Brush Cutters over 16.5 lbs (7.5 kg) dry weight (weight w/o fuel) require a double shoulder harness  
NOTE  
e Barrier Bar is used to restrict rearward movement of the unit. e Barrier Bar is NOT A HANDLE and should  
not be gripped when using or carrying the unit.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GRASS TRIMMER/BRUSH CUTTER  
OPERATOR'S MANUAL  
17  
Plastic/Nylon Grass/Weed Blades may be used where ever the nylon  
line head is used. DO NOT use this blade for heavy weeds or brush!  
8 Tooth Grass and Weed Blade is designed for grass, garden debris and  
thick weeds up to 19 mm (3/4”) diameter. DO NOT use this blade for  
brush or heavy woody growth.  
80 Tooth Brush Blade is designed for cutting brush and woody growth  
up to 13 mm (1/2 in.) diameter.  
22 Tooth Clearing Blade is designed for dense thickets and saplings  
up to 64 mm (2 1/2 in.) diameter.  
Use Shoulder/Waist Harness Use of the Shoulder/Waist Harness is  
recommended for ALL Trimmer/Brush Cutter use, not just Blade oper-  
ation. The Shoulder/Waist Harness when used in a trimming operation  
with nylon line head suspends the trimmer from the operator's shoulder  
and reduces operator fatigue.  
During blade operation, the same fatigue reduction is achieved. Safety  
to the operator is also enhanced by reducing the possibility of blade  
contact with the operator's hands and feet by restricting trimmer move-  
ment  
WARNING  
In case of emergency, pull the quick release latch to disconnect  
the trimmer from the harness.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18  
FUEL  
NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor  
performance, or severe engine damage and void the product warranty. Read and follow instructions in the Storage  
section of this manual.  
WARNING  
Alternative fuels, such as E-15 (15 % ethanol), E-85 (85 % ethanol) or any fuels not meeting ECHO requirements  
are NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels may cause performance  
problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited  
to, improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel lines, gaskets,  
carburetors and other engine components.  
Fuel Requirements  
Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain  
up to 10 % Ethanol (grain alcohol) or 15 % MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood  
alcohol) is NOT approved.  
Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FC/FD Standards must  
be used. ECHO brand premium Power Blend XTM Universal 2-Stroke Oil meets these standards. Engine problems due to  
inadequate lubrication caused by failure to use an ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FC/FD certied oil, such  
as ECHO premium Power Blend XTM, will void the two-stroke engine warranty.  
IMPORTANT  
ECHO premium Power Blend XTM Universal 2-Stroke Oil may be mixed at 50:1 ratio for application in all ECHO  
engines sold in the past regardless of ratio specied in those manuals.  
Handling Fuel  
DANGER  
Fuel is VERY ammable. Use extreme care when mixing, storing or handling or serious personal injury may result.  
• Use an approved fuel container.  
• DO NOT smoke near fuel.  
• DO NOT allow ames or sparks near fuel.  
• Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.  
• NEVER refuel a unit when the engine is HOT or RUNNING!  
• DO NOT ll fuel tanks indoors. ALWAYS ll fuel tanks outdoors over bare ground.  
• DO NOT overll fuel tank. Wipe up spills immediately.  
• Securely tighten fuel tank cap and close fuel container after refueling.  
• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.  
• Move at least 3m (10 ft.) from refueling location before starting the engine.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GRASS TRIMMER/BRUSH CUTTER  
OPERATOR'S MANUAL  
19  
Mixing Instructions  
1. Fill an approved fuel container with half of the required amount of  
gasoline.  
2. Add the proper amount of 2-stroke oil to gasoline.  
3. Close container and shake to mix oil with gasoline.  
4. Add remaining gasoline, close fuel container, and remix.  
IMPORTANT  
Spilled fuel is a leading cause of hydrocarbon emissions. Some  
states may require the use of automatic fuel shut-off containers to  
reduce fuel spillage.  
After use  
Shoulder  
level  
• DO NOT store a unit with fuel in its tank. Leaks can occur. Return  
unused fuel to an approved fuel storage container.  
Fuel tank  
Storage - Fuel storage laws vary by locality. Contact your local gov-  
ernment for the laws affecting your area. As a precaution, store fuel in  
an approved, airtight container. Store in a well-ventilated, unoccupied  
building, away from sparks and ames.  
IMPORTANT  
Stored fuel ages. Do not mix more fuel than you expect to use in  
thirty (30) days, ninety (90) days when a fuel stabilizer is added.  
IMPORTANT  
Stored two-stroke fuel may separate. ALWAYS shake fuel con-  
tainer thoroughly before each use.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
20  
STARTING COLD ENGINE  
A
WARNING  
When engine is started, conrm that there is not any abnormal  
vibration or sound. If there is abnormal vibration or sound, ask  
your DEALER to repair. After refueling tighten fuel cap rmly and  
check for leakage. In case of fuel leakage repair before starting  
operation since there is a danger of re.  
WARNING  
e attachment will operate immediately when the engine starts,  
and could result in possible serious injury. Keep movable parts of  
the attachment away from objects that could become entangled or  
thrown, and surfaces that could cause loss of control.  
B
1. Stop Switch  
Move stop switch (A) forward away from the STOP position.  
2. Choke  
Move choke lever (B) to Cold Start Position (  
).  
D
C
3. Purge Bulb  
Pump purge bulb (C) until fuel is visible and ows freely in the  
clear fuel tank return line. Pump bulb an additional 4 or 5 times.  
E
4. Press the decompression device (E).  
5. Recoil Starter  
Lay the unit on a at area and keep movable attachment parts clear  
of all obstacles. Hold unit rmly, and rapidly pull recoil starter  
handle/rope (D) until engine res (or maximum ve [5] pulls).  
D
6. Choke  
After engine res (or 5 pulls), move choke lever back to Run  
(
) position. Pull recoil starter starter handle/rope until engine  
starts and runs. Allow unit to warm up at idle for several minutes.  
NOTE  
If engine does not start with choke in “Run” position after 5 pulls,  
repeat instructions 2 - 5.  
7. Throttle Trigger  
After engine warm-up, gradually depress throttle trigger to increase  
engine RPM to operating speed.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GRASS TRIMMER/BRUSH CUTTER  
OPERATOR'S MANUAL  
21  
STARTING WARM ENGINE  
1. Press the decompression device (E).  
E
A
2. Stop Switch  
Move stop switch (A) forward away from the STOP position.  
3. Purge Bulb  
Pump purge bulb (C) until fuel is visible in the "Clear" fuel return  
line.  
D
C
4. Recoil Starter  
Lay the unit on a at area and keep movable attachment parts clear  
of all obstacles. Hold unit rmly and rapidly pull the recoil starter  
handle (D) until the engine res.  
D
NOTE  
If engine does not start after 5 pulls, use Cold Start Procedure.  
STOPPING ENGINE  
1. Release throttle trigger and allow to run at an idle speed.  
2. Slide ignition switch to “STOP” position.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
22  
MAINTENANCE  
WARNING  
Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all  
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete  
stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service.  
Wear gloves to protect hands from sharp edges and hot surfaces.  
Your ECHO trimmer is designed to provide many hours of trouble free service. Regular scheduled maintenance will help  
your trimmer achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take  
your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or  
have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed, see your ECHO Dealer for  
repairs.  
SKILL LEVELS  
Level 1 =  
Level 2 =  
Easy to do. Common tools may be required.  
Moderate difculty. Some specialized tools may be required.  
ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier.  
MAINTENANCE INTERVALS  
REQ'D  
SKILL  
LEVEL  
DAILY OR  
BEFORE  
USE  
3 MONTHS  
OR 90  
HOURS  
COMPONENT/  
SYSTEM  
MAINTENANCE  
PROCEDURE  
EVERY  
REFUEL  
YEARLY  
600 HOURS  
Air Filter  
Inspect/Clean  
1
1
1
1
I / C *  
I / C  
R *  
Choke Shutter  
Fuel Filter  
Inspect/Clean  
Inspect/Replace  
Inspect/Replace  
Inspect/Replace  
I *  
I / R *  
R *  
Fuel Cap Gasket  
Fuel System  
I *  
1
I (3) *  
I / C  
I (3) *  
Spark Plug  
Inspect/Clean  
Inspect/Clean  
1
2
2
2
I / C / R *  
Cooling System  
Muffler Spark Arrestor Inspect/Clean/Replace  
Cylinder Exhaust Port Inspect/Clean/Decarbon  
I / C / R *  
I / C  
Drive Shaft (Flex Cable  
Grease  
2
I (1)  
I (2)  
Models)  
Gear Housing  
Grease  
2
1
1
Recoil Starter Rope  
Screws/Nuts/Bolts  
Inspect/Clean  
Inspect/Tighten/Replace  
I / C *  
I *  
MAINTENANCE PROCEDURE LETTER CODES: I = INSPECT, R = REPLACE, C = CLEAN  
IMPORTANT NOTE - Time intervals shown are maximum. Actual use and your experience will determine the  
frequency of required maintenance.  
MAINTENANCE PROCEDURE NOTES:  
(1) Apply POWER BLENDXTM grease every 25 hours of use.  
(2) Apply POWER BLENDXTM grease every 50 hours of use.  
(3) Low evaporative fuel tanks DO NOT require regular maintenance to maintain emission integrity.  
* Replacement is recommended based on the finding of damage or wear during inspection.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GRASS TRIMMER/BRUSH CUTTER  
OPERATOR'S MANUAL  
23  
AIR FILTER  
Level 1.  
Tools required: 25 - 50 mm (1 - 2 in.) cleaning brush  
Parts required: REPOWERTM Tune-Up Kit  
NOTE  
Always brush dirt and debris away from air cleaner area prior to  
cleaning air lter.  
1. Brush dirt off air cleaner area. Keep dirt away from engine and air  
intake grid.  
B
2. Remove air lter cover (A). Brush dirt from inside cover and away  
from edges of air lter.  
A
3. Check air lter seal for tight t with air lter case.  
4. Remove air lter (B) from case. Use care to prevent dirt and debris  
from falling into air lter case.  
5. Inspect lter element and seal. Replace lter if any of these prob-  
lems are present:  
•Air lter seal does not t tightly against case  
•Air lter seal is distorted, worn, or damaged  
•Air lter element has holes or other damage  
•Air lter element is saturated with dirt  
•Air lter element is soaked with fuel mix  
6. If air lter is in good condition and can be cleaned and reused,  
lightly brush debris from air lter element, or blow lter element  
clean using low pressure (40 psi or less) compressed air directed at  
inside of lter.  
IMPORTANT  
When using compressed air, always direct air stream at inside sur-  
face of lter so dust and debris will be blown out of lter. Keep air  
nozzle 6 - 8 inches away from lter to prevent damage to lter.  
7. Install air lter in case, and replace cover.  
NOTICE  
Actual replacement interval for air lter depends on operating con-  
ditions. Operation in dustier applications requires more frequent  
cleaning and replacement. Continued operation with a damaged  
or excessively dirty lter will allow dirt and debris to enter engine,  
and result in poor performance, rapid engine wear, and premature  
engine failure.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
24  
FUEL FILTER  
Level 1.  
Tools required: 200- 250 mm (8 - 10 in.) length of wire with one end  
bent into a hook, clean rag, funnel, and an approved  
fuel container.  
Parts required: REPOWERTM Tune-Up Kit  
DANGER  
Fuel is VERY ammable. Use extreme care when mixing, storing or  
handling.  
1. Use a clean rag to remove loose dirt from around fuel cap and  
empty fuel tank.  
2. Use the “fuel line hook” to pull the fuel line and lter from the  
tank.  
3. Remove the lter from the line and install the new lter.  
NOTE  
Federal EPA regulations require all model year 2012 and later  
gasoline powered engines produced for sale in the United States to  
be equipped with a special low permeation fuel supply hose between  
the carburetor and fuel tank. When servicing model year 2012 and  
later equipment, only fuel supply hoses certified by EPA can be used  
to replace the original equipment supply hose. Fines up to $37,500  
may be enforced for using an un-certified replacement part.  
SPARK PLUG  
Level 2.  
Tools Required: Spark plug wrench, feeler gauge, soft metal brush.  
Parts Required: REPOWERTM Tune-Up Kit  
1. Remove spark plug and check for fouling, worn and rounded  
center electrode.  
2. Clean the plug or replace with a new one. DO NOT sand blast to  
clean. Remaining sand will damage engine.  
3. Adjust spark plug gap by bending outer electrode.  
4. Install Spark Plug, and tighten to 130-150 in•lbf  
(150-170 kgf•cm).  
0.6 - 0.7 mm (.024 - .028 in)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GRASS TRIMMER/BRUSH CUTTER  
OPERATOR'S MANUAL  
25  
COOLING SYSTEM  
Level 2.  
Tools required: Air compressor and safety nozzle, or: 4 mm Hex  
wrench, 25 - 50 mm (1 - 2 in.) cleaning brush.  
Parts Required: None.  
IMPORTANT  
To maintain proper engine operating temperatures, cooling air must  
pass freely through the cylinder n area. This ow of air carries  
combustion heat away from the engine.  
Overheating and engine seizure can occur when:  
• Air intakes are blocked, preventing cooling air from reaching the  
cylinder.  
• Dustanddebrisbuild-upontheoutsideofthecylinder.Thisbuild-up  
insulates the engine and prevents the heat from leaving.  
Removal of cooling passage blockages and cleaning of cooling ns is  
considered “Normal Maintenance.” Any failure attributed to lack of  
maintenance is not warranted.  
1. Periodically blow dirt and debris off cooling ns with a compres-  
sor and safety nozzle, or;  
2. Remove engine and mufer covers, and brush off dirt and debris  
using the medium bristle brush.  
EXHAUST SYSTEM  
Spark Arrestor Screen  
Level 2.  
Tools Required: Cross Head Screwdriver, Soft Metal Brush, 4 mm  
Hex Wrench  
A
Parts Required: Spark Arrestor Screen, Gasket  
1. Remove mufer cover (A).  
2. Place piston at Top Dead Center (TDC) to prevent carbon/dirt from  
entering cylinder.  
3. Remove spark arrestor screen cover (B), screen holder (C), gasket  
(D), and screen (E), from mufer body.  
4. Clean carbon deposits from mufer components.  
5. Replace screen if it is cracked, plugged, or has holes burned  
through.  
B
E
D
C
6. Assemble components in reverse order.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
26  
Exhaust Port Cleaning  
Level 2.  
Tools required: 4 & 5 mm Hex Wrench, Wood or plastic scraper  
Parts Required: As needed: Heat Shield  
1. Remove spark plug lead from spark plug, and remove mufer  
A
cover (2 screws).  
B
2. Place piston at top dead center. Remove mufer (A) and heat shield  
(B).  
3. Use a wood or plastic scraping tool to clean deposits from cylinder  
exhaust port.  
IMPORTANT  
Never use a metal tool to scrape carbon from the exhaust port.  
Do not scratch the cylinder or piston when cleaning the exhaust  
port. Do not allow carbon particles to enter the cylinder.  
4. Inspect heat shield, and replace if damaged.  
5. Install heat shield and mufer.  
6. Tighten mufer mounting bolts (or nuts) to 95-130 in•lbf (110-150  
kgf•cm).  
7. Attach spark plug lead and install mufer cover.  
8. Start engine, and warm to operating temperature.  
9. Stop engine, and re-tighten mounting bolts (or nuts) to specica-  
tions.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GRASS TRIMMER/BRUSH CUTTER  
OPERATOR'S MANUAL  
27  
CARBURETOR ADJUSTMENT  
Engine Break-In  
New engines must be operated a minimum of two tanks of fuel before carburetor adjustments can be made. During the  
break-in period your engine performance will increase and exhaust emissions will stabilize. Idle speed can be adjusted as  
required.  
High Altitude Operation  
This engine has been factory adjusted to maintain satisfactory starting, emission, and durability performance up to 1100  
feet above sea level (ASL) (96.0 kPa). To maintain proper engine operation and emission compliance above 1100 feet  
ASL the carburetor may need to be adjusted by an authorized ECHO service dealer.  
IMPORTANT  
If the engine is adjusted for operation above 1100 feet ASL, the  
carburetor must be re-adjusted when operating the engine below  
1100 feet ASL, otherwise severe engine damage may result.  
Level 2.  
Tools required: Screwdriver, Tachometer (ECHO P/N 99051130017).  
Parts required: None.  
1. Before adjusting carburetor clean or replace air lter and mufer,  
“Spark Arrestor Screen”.  
2. Make sure the cutting attachment such as hedge clipper blades  
or circular saw are properly adjusted. Trimmer line should be  
extended to cut-off knife.  
3. Start engine and run several minutes to bring to operating tempera-  
Idle speed adjustment screw (T)  
ture. Flash choke twice during warm-up to clear any air from the  
fuel system.  
4. Idle Speed Adjustment  
• Start engine, turn “idle” speed adjustment screw clockwise  
(CW) until the cutting attachment begins to turn, then turn screw  
out counterclockwise (CCW) until attachment stops turning. Turn  
screw out, CCW, an additional 1/4 turn.  
WARNING  
Cutting attachment must not turn or move when unit is idling.  
CAUTION  
When starting, idling adjustment speed should be adjusted not to  
rotate the cutting attachment. Correct idle speed is adjusted 2300 to  
2700 r/min. Or 1/4 turn CCW from the point the cutting attachment  
stops moving. When there is some trouble with the carburetor, refer  
to your dealer.  
NOTE  
Every unit is run at the factory and the carburetor is set in compli-  
ance with emission regulations. Carburetor adjustments, other than  
idle speed, must be performed by an authorized ECHO dealer.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
28  
LUBRICATION  
Level 1.  
Tools Required: 8 & 13 mm Open End Wrench, Screwdriver,  
Clean Rag.  
Parts Required: POWER BLENDXTM 8 oz. (P/N 91014) or Lithium  
Base Grease.  
Gear Housing  
B
1. Clean all loose debris from gear box.  
2. Remove the plug (A) and drain screw (B) from the gear case.  
3. Add grease into the gear case until old grease is pushed out. If  
necessary, use a low pressure pump.  
A
4. Reinstall the drain screw and plug.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GRASS TRIMMER/BRUSH CUTTER  
OPERATOR'S MANUAL  
29  
SHARPENING METAL BLADES  
Three styles of metal blades are approved for use on the ECHO Brush  
Cutter. The 8-tooth blade can be sharpened during normal mainte-  
nance. The clearing blade and 80 tooth blade require professional  
service.  
Before sharpening, CLOSELY inspect blade for cracks (look at the  
bottom of each tooth and the center mounting hole closely), missing  
teeth and bending. If ANY of these problems are discovered, replace  
the blade.  
When sharpening a blade, always remove the same amount of materials  
from each tooth to maintain balance. A blade that is not balanced will  
cause unsafe handling due to vibration and can result in blade failure.  
Tool required:  
Flatle(preferred). Electricgrinderifspecialcareis  
used. Round (rat tail) le for gullet (radius).  
1. File each tooth at a 30 degree angle a specic number of times,  
eg. 4 strokes per tooth. Work your way around the blade until  
all teeth are sharp.  
2. DO NOT le the 'gullet' (radius) of the tooth with the at le.  
The radius must remain. A sharp corner will lead to a crack and  
blade failure.  
IMPORTANT  
If an electric grinder is used, use care not to overheat teeth, do not  
allow tips/tooth to glow red or turn blue. DO NOT place blade in  
cooling water. This will change the temper of the blade and could  
result in blade failure.  
3. After sharpening teeth, check each tooth radius for evidence of a  
square (sharp) corner. Use the round (rat tail) le to renew the  
radius.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
30  
TROUBLESHOOTING  
ENGINE PROBLEM TROUBLESHOOTING CHART  
Status Cause  
Problem  
Check  
Remedy  
Clean or replace  
Fuel at carburetor  
No fuel at carburetor Fuel strainer clogged  
Fuel line clogged  
Clean or replace  
Carburetor  
See your Echo dealer  
Fuel at cylinder  
No fuel at cylinder  
Carburetor  
See your Echo dealer  
Muffler wet with fuel Fuel Mixture too rich  
Open choke  
Engine  
cranks -  
starts hard/  
doesn't  
Clean/replace air filter  
Adjust carburetor  
See your Echo dealer  
Spark at end  
of plug wire  
No spark  
No spark  
Stop switch off  
Electrical problem  
Interlock switch  
Turn switch to ON  
See your Echo dealer  
See your Echo dealer  
start  
Spark at plug  
Spark gap incorrect  
Covered with carbon  
Fouled with fuel  
Adjust to .65mm (0.026 in.)  
Clean or replace  
Clean or replace  
Plug defective  
Replace plug  
Air filter  
Air filter dirty  
Normal wear  
Clean or replace  
Fuel filter  
Fuel filter dirty  
Contaminants/residues in Replace  
fuel  
Fuel vent  
Fuel vent plugged  
Contaminants/residues in Clean or replace  
fuel  
Engine runs,  
but dies or  
does not  
accelerate  
properly  
Spark Plug  
Carburetor  
Plug dirty/worn  
Normal wear  
Clean and adjust or replace  
Improper adjustment Vibration  
Adjust  
Clean  
Cooling System  
Cooling system  
dirty/plugged  
Extended operation in  
dirty/dusty locations  
Spark Arrestor  
Screen  
Spark arrestor  
screen plugged  
Normal wear  
Replace  
Engine does  
not crank  
N/A  
N/A  
Internal engine problem  
See your Echo dealer  
DANGER  
Fuel vapors are extremely ammable and may cause re and/or explosion. Never test for ignition spark by ground-  
ing spark plug near cylinder plug hole, otherwise serious personal injury may result.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GRASS TRIMMER/BRUSH CUTTER  
OPERATOR'S MANUAL  
31  
STORAGE  
WARNING  
During operation the mufer or catalytic mufer and surrounding cover become hot. Always keep exhaust area clear  
of ammable debris during transportation or when storing, otherwise serious property damage or personal injury  
may result.  
Long Term Storage (over 30 days)  
Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage mainte-  
nance which includes the following:  
1. Store unit in a dry, dust free place, out of the reach of children.  
DANGER  
Do not store in enclosure where fuel fumes may accumulate or reach an open ame or spark.  
2. Place the stop switch in the "STOP" position.  
7. Remove the spark plug and pour 7 cc (1/4 oz.) of  
fresh, clean, two-stroke engine oil into the cylinder  
through the spark plug hole.  
3. Remove accumulation of grease, oil, dirt and debris  
from exterior of unit.  
A. Place a clean cloth over the spark plug hole.  
4. Perform all periodic lubrication and services that are  
required.  
B. Pulltherecoilstarterhandle2-3timestodistribute  
the oil inside the engine.  
5. Tighten all the screws and nuts.  
C. Observe the piston location through the spark  
plug hole. Pull the recoil handle slowly until the  
piston reaches the top of its travel and leave it  
there.  
6. Drain the fuel tank completely and pull the recoil  
starter handle several times to remove fuel from the  
carburetor.  
8. Install the spark plug (do not connect ignition cable).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
32  
SPECIFICATIONS  
MODEL ---------------------------------------------------- SRM-410U  
Length ------------------------------------------------------- 1860 mm (73.2 in.)  
Width -------------------------------------------------------- 630 mm (24.8 in.)  
Height ------------------------------------------------------- 470 mm (18.5 in.)  
Weight (dry) w/Cutter Head------------------------------ 8.3 kg (18.3 lb.)  
Engine Type ------------------------------------------------ Air cooled, two-stroke, single cylinder gasoline engine  
Bore---------------------------------------------------------- 40.0 mm (1.58 in.)  
Stroke-------------------------------------------------------- 34.0 mm (1.34 in.)  
Displacement ----------------------------------------------- 42.7 cc (2.61 cu. in.)  
Exhaust------------------------------------------------------ Spark arrestor mufer or spark arrestor mufer with catalyst  
Carburetor--------------------------------------------------- Walbro w/purge pump  
Ignition System -------------------------------------------- Flywheel magneto, capacitor discharge ignition type  
Spark Plug -------------------------------------------------- NGK BPM7A (Gap 0.65 mm (0.026 in.)  
Fuel ---------------------------------------------------------- Mixed (Gasoline and Two-stroke Oil)  
Fuel/Oil Ratio ---------------------------------------------- 50 : 1 Power Blend X™ ISO-L-EGD (ISO/CD 13738) and  
J.A.S.O. M345- FC/FD, two-stroke, air-cooled engine oil.  
Gasoline----------------------------------------------------- Use 89 Octane unleaded. Do not use fuel containing methyl  
alcohol, more than 10 % ethyl alcohol or 15 % TBE. Do not use  
alternative fuels such as E-20 or E-85.  
Oil------------------------------------------------------------ Power Blend XTM Premium Universal 2-Stroke Oil  
Fuel Tank Capacity ---------------------------------------- 1.0 L (33.8 US . oz.)  
Starter System---------------------------------------------- Automatic Rewind Starter  
Clutch-------------------------------------------------------- Centrifugal Type  
Vibration Isolated System -------------------------------- Rubber cushion on engine mount (heavy duty). Rubber grip on  
front handle.  
Operating Rod---------------------------------------------- 28.0 mm aluminum Tube  
Drive Shaft-------------------------------------------------- 8.0 mm  
Gear Case Ratio-------------------------------------------- 1.33 Reduction  
Rotating Direction ----------------------------------------- Counter Clockwise; viewed from top  
Cutter Head------------------------------------------------- 10 in. 80 - tooth blade  
Handle------------------------------------------------------- U-Handle  
Shoulder Harness ------------------------------------------ Standard  
Idle Speed--------------------------------------------------- 2300 - 2700 RPM  
Clutch Engagement Speed-------------------------------- 3500 RPM  
Wide Open Throttle Speed (W.O.T.) -------------------- 10000 - 11500 RPM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GRASS TRIMMER/BRUSH CUTTER  
OPERATOR'S MANUAL  
33  
WARRANTY STATEMENTS  
ECHO LIMITED WARRANTY STATEMENT FOR  
PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010  
ECHO'S RESPONSIBILITY  
ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship.  
Under normal use and maintenance from date of purchase, ECHO agrees to repair or replace at ECHO’s discretion, any defective product  
free of charge at any authorized ECHO servicing dealer within listed below application time periods, limitations and exclusions. THIS LIMITED  
WARRANTY IS ONLYAPPLICABLE TO ECHO PRODUCTS SOLD BYAUTHORIZED ECHO DEALERS. IT IS EXTENDED TO THE ORIGINAL  
PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair  
parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period. Any  
damage caused by improper installation or improper maintenance is not covered by this warranty. All parts or products replaced under warranty  
become the property of ECHO, Inc. This warranty is separate from the Emission control warranty statement supplied with your new product.  
Please consult the Emission Control Warranty Statement for details regarding emission related parts. For a list of Authorized ECHO Dealers  
refer to WWW.ECHO-USA.COM or call 1-800-432-ECHO.  
OWNER’S RESPONSIBILITY  
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at WWW.ECHO-USA.COMꢀRUꢀE\ꢀ¿OO-  
LQJꢀRXWꢀWKHꢀZDUUDQW\ꢀUHJLVWUDWLRQꢀFDUGꢀVXSSOLHGꢀZLWKꢀ\RXUꢀXQLWꢁꢀ5HJLVWHULQJꢀ\RXUꢀSURGXFWꢀFRQ¿UPVꢀ\RXUꢀZDUUDQW\ꢀFRYHUDJHꢀDQGꢀSURYLGHVꢀDꢀGLUHFWꢀ  
OLQNꢀLIꢀZHꢀ¿QGꢀLWꢀQHFHVVDU\ꢀWRꢀFRQWDFWꢀ\RXꢁ  
The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in the  
RSHUDWRU¶VꢀPDQXDOꢁꢀ6KRXOGꢀDꢀSURGXFWꢀGLI¿FXOW\ꢀRFFXUꢂꢀ\RXꢀPXVWꢂꢀDWꢀ\RXUꢀH[SHQVHꢂꢀGHOLYHUꢀRUꢀVKLSꢀ\RXUꢀ(&+2ꢀXQLWꢀWRꢀDQꢀDXWKRUL]HGꢀ(&+2ꢀVHUYLFLQJꢀ  
dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit after the repairs have been  
made. For your nearest authorized ECHO servicing dealer, call ECHO’s Dealer Referral Center, at 1-800-432-ECHO or you can locate an ECHO  
servicing dealer at WWW.ECHO-USA.COM. Should you require assistance or have questions concerning ECHO’s Warranty Statement, you  
can contact our Consumer Product Support Department at 1-800-673-1558 or contact us through the web at WWW.ECHO-USA.COM.  
PRODUCT WARRANTY PERIOD  
RESIDENTIAL APPLICATION  
‡ꢀꢀ 5 YEAR WARRANTY - All units for residential, or non-income producing use will be covered by this limited warranty for ¿YH ꢀꢁꢂꢃ\HDUV from  
date of purchase.  
EXCEPTIONS:  
‡ꢀ )RUꢀWZRꢃVWURNHꢀHQJLQHꢀSRZHUHGꢀSURGXFWVꢂꢀWKHꢀHOHFWURQLFꢀLJQLWLRQꢀPRGXOHꢂꢀÀH[LEOHꢀGULYHꢀFDEOHVꢂꢀ650ꢀVROLGꢀGULYHꢀVKDIWVꢂꢀDQGꢀ7&ꢀWLQHVꢀ  
are warranted for the OLIHꢄ of the product on parts only.  
‡ꢀ &XWWLQJꢀDWWDFKPHQWVꢀVXFKꢀDVꢂꢀEXWꢀQRWꢀOLPLWHGꢀWRꢂꢀEDUVꢂꢀFKDLQVꢂꢀVSURFNHWVꢂꢀEODGHVꢂꢀDQGꢀQ\ORQꢀWULPPHUꢀKHDGVꢀIRUꢀUHVLGHQWLDOꢀRUꢀQRQꢃLQFRPHꢀ  
producing use will be covered for failures due to defects in material or workmanship for a period of ꢅꢆꢃGD\V from original product  
purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty.  
‡ꢀꢀ (&+2¶Vꢀ5DSLGꢀ/RDGHUꢀ6WULQJꢀ+HDGꢀFDUULHVꢀDꢀOLIHWLPHꢀZDUUDQW\ꢀRQꢀWKHꢀOLQHꢀORFNLQJꢀV\VWHPꢂꢀSDUWVꢀRQO\ꢄꢀQRꢀODERUꢁꢀ5HIHUꢀWRꢀ\RXUꢀRSHUDWRU¶Vꢀ  
manual for string head installation and maintenance instructions.  
‡ꢀꢀ $OO6%ꢃ6HULHVDQG352ꢀ$77$&+0(176(5,(66SOLW6KDIWDWWDFKPHQWVFDUU\WKHVDPHZDUUDQW\GXUDWLRQDVWKHXQLWVWKH\DUHꢀ  
GHVLJQHGꢀWRꢀ¿Wꢁ  
COMMERCIAL APPLICATION  
‡ꢀꢀ 1 YEAR WARRANTY - All Chain Saws, QuikVent Saws, and Cut-Off Saws for commercial, institutional, agricultural, industrial, or income  
producing use will be covered by this limited warranty for one ꢀꢇꢂꢃ\HDU from the date of purchase.  
‡ꢀꢀ 2 YEAR WARRANTY - All other units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this  
limited warranty for two ꢀꢈꢂꢃ\HDUV from the date of purchase.  
EXCEPTIONS:  
‡ꢀ )RUꢀWZRꢃVWURNHꢀHQJLQHꢀSRZHUHGꢀSURGXFWVꢂꢀWKHꢀHOHFWURQLFꢀLJQLWLRQꢀPRGXOHꢂꢀÀH[LEOHꢀGULYHꢀFDEOHVꢂꢀ650ꢀVROLGꢀGULYHꢀVKDIWVꢀDQGꢀ7&ꢀWLQHVꢂꢀ  
are warranted for the OLIHꢄ of the product on parts only.  
‡ꢀ &XWWLQJꢀDWWDFKPHQWVꢀVXFKꢀDVꢂꢀEXWꢀQRWꢀOLPLWHGꢀWRꢂꢀEDUVꢂꢀFKDLQVꢂꢀVSURFNHWVꢂꢀEODGHVꢂꢀDQGꢀQ\ORQꢀWULPPHUꢀKHDGVꢀIRUꢀFRPPHUFLDOꢂꢀLQVWLWXWLRQDOꢂꢀ  
agricultural, industrial, rental, or income producing will be covered for failures due to defects in material or workmanship for a period  
of ꢉꢆꢃGD\V from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by  
this warranty.  
‡ꢀꢀ (&+2¶Vꢀ5DSLGꢀ/RDGHUꢀ6WULQJꢀ+HDGꢀFDUULHVꢀDꢀOLIHWLPHꢀZDUUDQW\ꢀRQꢀWKHꢀOLQHꢀORFNLQJꢀV\VWHPꢂꢀSDUWVꢀRQO\ꢄꢀQRꢀODERUꢁꢀ5HIHUꢀWRꢀ\RXUꢀRSHUDWRU¶Vꢀ  
manual for string head installation and maintenance instructions.  
‡ꢀꢀ $OO6%ꢃ6HULHVDQG352ꢀ$77$&+0(176(5,(66SOLW6KDIWDWWDFKPHQWVFDUU\WKHVDPHZDUUDQW\GXUDWLRQDVWKHXQLWVWKH\DUHꢀ  
GHVLJQHGꢀWRꢀ¿Wꢁ  
RENTAL APPLICATION - 90 DAYS WARRANTY  
‡ꢀꢀ8QLWVꢀIRUꢀUHQWDOꢀXVHꢀZLOOꢀEHꢀFRYHUHGꢀDJDLQVWꢀGHIHFWVꢀLQꢀPDWHULDOꢀDQGꢀZRUNPDQVKLSꢀIRUꢀDꢀSHULRGꢀRIꢀꢅꢆꢀGD\VꢀIURPꢀWKHꢀGDWHꢀRIꢀSXUFKDVHꢁꢀ  
ꢀꢀ (&+2¶VꢀOLDELOLW\ꢀXQGHUꢀWKHꢀ³/LIHWLPH´ꢀFRYHUDJHꢀLVꢀOLPLWHGꢀWRꢀIXUQLVKLQJꢀSDUWVꢀVSHFL¿HGꢀXQGHUꢀWKHꢀ352'8&7ꢀ:$55$17<ꢀ3(5,2' section of  
this warranty statement for ³/LIH´ꢀIUHHꢀRIꢀFKDUJHꢀIRUꢀDꢀSHULRGꢀRIꢀWHQꢀꢇꢈꢆꢉꢀ\HDUVꢀDIWHUꢀWKHꢀGDWHꢀRIꢀWKHꢀFRPSOHWHꢀXQLW¶Vꢀ¿QDOꢀSURGXFWLRQꢁꢀ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
34  
PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES  
‡ꢀꢀꢁꢂꢃGD\ꢀUHVLGHQWLDOꢄꢀRUꢀQRQꢃLQFRPHꢀSURGXFLQJꢀZDUUDQW\  
‡ꢀꢀꢅꢂꢃGD\ꢀFRPPHUFLDOꢄꢀLQVWLWXWLRQDOꢄꢀDJULFXOWXUDOꢄꢀLQGXVWULDOꢄꢀLQFRPHꢀSURGXFLQJꢄꢀRUꢀUHQWDOꢀDSSOLFDWLRQꢀZDUUDQW\ꢀꢀ  
ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS  
This ECHO two-stroke engine power product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior  
performance. To help ensure the performance of the unit, it is required to use two-stroke oil which meets the ISO-L-EGD Standard per ISO/CD  
13738 and JASO M345FD Standards. (&+2ꢀ3RZHUꢀ%OHQGŒꢀ7ZRꢁ6WURNHꢀ2LO LVꢀDꢀSUHPLXPꢀWZRꢃVWURNHꢀRLOꢀVSHFL¿FDOO\ꢀIRUPXODWHGꢀWRꢀPHHWꢀ,62ꢃ  
L-EGD (ISO/CD 13738) and JASO M345FD Standards. The use of two-stroke oils designed for other applications, such as for outboard motors  
or lawnmowers can result in severe engine damage, and will void your two-stroke engine limited warranty.  
THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY:  
‡ꢀ  
/DFNꢀRIꢀOXEULFDWLRQꢀRUꢀHQJLQHꢀIDLOXUHꢄꢀGXHꢀWRꢀWKHꢀXVHꢀRIꢀWZRꢃVWURNHꢀRLOVꢀthat do not meet the ISO-L-EGD (ISO/CD 13738) and JASO M345FD  
Standards. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD compliant and JASO M345FD registered  
oil, will void the two-stroke engine limited warranty. (&+23RZHU%OHQGŒ7ZRꢃ6WURNH2LO meets the ISO-L-EGD and JASO M345FD  
Standard. Emission related parts are covered for 5 years residential use or 2 years commercial use regardless of two-stroke oil used, per  
the statement listed in the EPA or California Emission Defect Warranty Explanation.  
‡ꢀ  
'DPDJHꢀFDXVHGꢀE\ꢀXVHꢀRIꢀJDVRKROꢄꢀFRQWDLQLQJꢀPHWKDQROꢀꢆZRRGꢀDOFRKROꢇꢄꢀRUꢀJDVROLQHꢀFRQWDLQLQJꢀOHVVꢀWKDQꢀꢈꢁꢀRFWDQH. Only use gasoline which  
contains ꢈꢁꢀRFWDQHꢀRUꢀKLJKHU. Gasohol which contains a PD[LPXPꢀꢉꢂꢊꢀHWKDQROꢀꢆJUDLQꢀDOFRKROꢇꢀRUꢀꢉꢋꢊꢀ07%(ꢀꢆPHWK\OꢌWHUWLDU\ꢌEXW\OꢌHWKHUꢇꢀ  
is also approved. The prescribed mixing ratio of gasoline to oil is listed on the ECHO oil label and covered in your operator’s manual.  
(QJLQHꢀGDPDJHꢀFDXVHGꢀE\ꢀXVHꢀRIꢀHWKHUꢀRUꢀDQ\ꢀVWDUWLQJꢀÀXLGVꢍꢀꢀ  
'DPDJHꢀFDXVHGꢀE\ꢀWDPSHULQJꢀZLWKꢀHQJLQHꢀVSHHGꢀJRYHUQRUꢀRUꢀHPLVVLRQꢀFRPSRQHQWVꢄꢀRUꢀUXQQLQJꢀHQJLQHVꢀDERYHꢀVSHFL¿HGꢀDQGꢀUHFRPPHQGHGꢀ  
engine speeds as listed in your operator’s manual.  
‡ꢀ  
‡ꢀ  
‡ꢀ  
‡ꢀ  
‡ꢀ  
2SHUDWLRQꢀRIꢀWKHꢀXQLWꢀZLWKꢀLPSURSHUO\ꢀPDLQWDLQHGꢌUHPRYHGꢀFXWWLQJꢀVKLHOGꢀRUꢀUHPRYHGꢌGDPDJHGꢀDLUꢀ¿OWHUꢍꢀꢀ  
'DPDJHꢀFDXVHGꢀE\ꢀGLUWꢄꢀSUHVVXUHꢀRUꢀVWHDPꢀFOHDQLQJꢀWKHꢀXQLWꢄꢀVDOWꢀZDWHUꢄꢀFRUURVLRQꢄꢀUXVWꢄꢀYDUQLVKꢄꢀDEUDVLYHVꢄꢀDQGꢀPRLVWXUHꢍ  
'HIHFWVꢄꢀPDOIXQFWLRQVꢀRUꢀIDLOXUHVꢀUHVXOWLQJꢀIURPꢀDEXVHꢄꢀPLVXVHꢄꢀQHJOHFWꢄꢀPRGL¿FDWLRQVꢄꢀDOWHUDWLRQVꢄꢀQRUPDOꢀZHDUꢄꢀLPSURSHUꢀVHUYLFLQJꢄꢀRUꢀXVHꢀ  
of unauthorized attachments.  
‡ꢀ  
‡ꢀ  
,QFRUUHFWꢀVWRUDJHꢀSURFHGXUHVꢄꢀVWDOHꢀIXHOꢄꢀLQFOXGLQJꢀIDLOXUHꢀWRꢀSURYLGHꢀRUꢀSHUIRUPꢀUHTXLUHGꢀPDLQWHQDQFHꢀVHUYLFHVꢀDVꢀSUHVFULEHGꢀLQꢀWKHꢀRSHUDWRUꢎVꢀ  
manual. Preventative maintenance as outlined in the operators manual is the customer’s responsibility.  
)DLOXUHVꢀGXHꢀWRꢀLPSURSHUꢀVHWꢃXSꢄꢀSUHꢃGHOLYHU\ꢀVHUYLFHꢀRUꢀUHSDLUꢀVHUYLFHꢀE\ꢀDQ\RQHꢀRWKHUꢀWKDQꢀDXWKRUL]HGꢀ(&+2ꢀVHUYLFLQJꢀGHDOHUꢀGXULQJꢀWKHꢀ  
warranty period.  
‡ꢀ  
‡ꢀ  
&HUWDLQꢀparts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups.  
8VHRIVSDUNSOXJVRWKHUWKDQWKRVHPHHWLQJSHUIRUPDQFHDQGGXUDELOLW\UHTXLUHPHQWVRIWKH2(0VSDUNSOXJOLVWHGLQWKH2SHUDWRUꢎVꢀ  
Manuals.  
‡ꢀ  
2YHUKHDWLQJꢀRUꢀFDUERQꢀVFRULQJꢀIDLOXUHVꢀGXHꢀWRꢀUHVWULFWHGꢄꢀFORJJHGꢀH[KDXVWꢀSRUWꢀRUꢀFRPEXVWLRQꢀFKDPEHUꢄꢀLQFOXGLQJꢀGDPDJHꢀWRꢀVSDUNꢀDUUHVWHUꢀ  
screen.  
‡ꢀ  
‡ꢀ  
$GMXVWPHQWVꢀDIWHUꢀWKHꢀ¿UVWꢀꢆꢅꢂꢇꢀWKLUW\ꢀGD\VꢀDQGꢀEH\RQGꢄꢀVXFKꢀDVꢀFDUEXUHWRUꢀDGMXVWPHQWꢀDQGꢀWKURWWOHꢀFDEOHꢀDGMXVWPHQWꢍꢀ  
'DPDJHꢀWRꢀJHDUVꢀRUꢀJHDUꢀFDVHVꢀFDXVHGꢀE\ꢀFRQWDPLQDWHGꢀJUHDVHꢀRUꢀRLOꢄꢀXVHꢀRIꢀLQFRUUHFWꢀW\SHꢀRUꢀYLVFRVLW\ꢀRIꢀOXEULFDQWVꢄꢀDQGꢌRUꢀIDLOXUHꢀWRꢀFRPSO\ꢀ  
with recommended grease or oil change intervals.  
®
‡ꢀ  
‡ꢀ  
‡ꢀ  
'DPDJHꢀFDXVHGꢀE\ꢀORDGLQJꢀ6+5('ꢀꢎ1ꢎꢀ9$& beyond recommended capacity.  
'DPDJHꢀFDXVHGꢀE\ꢀSXPSꢀRUꢀVSUD\HUꢀUXQQLQJꢀGU\ꢄꢀSXPSLQJꢀRUꢀVSUD\LQJꢀFDXVWLFꢀRUꢀÀDPPDEOHꢀPDWHULDOVꢄꢀRUꢀODFNꢀRIꢀRUꢀEURNHQꢀVWUDLQHUVꢍꢀ  
$GGLWLRQDOꢀGDPDJHꢀWRꢀSDUWVꢀRUꢀFRPSRQHQWVꢀGXHꢀWRꢀFRQWLQXHGꢀXVHꢀDIWHUꢀRSHUDWLRQDOꢀSUREOHPꢀRUꢀIDLOXUHꢀRFFXUVꢍꢀ6KRXOGꢀRSHUDWLRQDOꢀSUREOHPꢀRUꢀ  
failure occur, the product should not be used, but delivered as is to an authorized ECHO servicing dealer.  
It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your ECHO product or by visiting  
WWW.ECHO-USA.COMꢍꢀ<RXUꢀUHFHLSWꢀRIꢀSXUFKDVHꢀLQFOXGLQJꢀGDWHꢄꢀPRGHOꢀDQGꢀVHULDOꢀQXPEHUꢀPXVWꢀEHꢀPDLQWDLQHGꢀDQGꢀSUHVHQWHGꢀWRꢀDQꢀDXWKRUL]HGꢀ  
ECHO servicing dealer for warranty service. Proof of purchase rests solely with the customer. Some states do not allow limitations on how long  
an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the exclusion or limitation of incidental or  
FRQVHTXHQWLDOꢀGDPDJHVꢄꢀVRꢀ\RXꢀPD\ꢀDOVRꢀKDYHꢀRWKHUꢀVSHFL¿FꢀOHJDOꢀULJKWVꢀZKLFKꢀYDU\ꢀIURPꢀVWDWHꢀWRꢀVWDWHꢍꢀ7KLVꢀOLPLWHGꢀZDUUDQW\ꢀLVꢀJLYHQꢀE\ꢀ(&+2ꢀ  
Incorporated, 400 Oakwood Rd., Lake Zurich, IL 60047.  
DISCLAIMER OF IMPLIED WARRANTIES  
7KLVꢀOLPLWHGꢀZDUUDQW\ꢀLVꢀLQꢀOLHXꢀRIꢀDOOꢀRWKHUꢀH[SUHVVHGꢀRUꢀLPSOLHGꢀZDUUDQWLHVꢄꢀLQFOXGLQJꢀDQ\ꢀZDUUDQW\ꢀRIꢀ),71(66ꢀ)25ꢀ$ꢀ3$57,&8/$5ꢀ385326(ꢀ  
OR USE and any implied warranty of MERCHANTABILITYꢀRWKHUZLVHꢀDSSOLFDEOHꢀWRꢀWKLVꢀSURGXFWꢍꢀ(&+2ꢀDQGꢀLWVꢀDI¿OLDWHGꢀFRPSDQLHVꢀVKDOOꢀQRWꢀEHꢀ  
OLDEOHꢀIRUꢀDQ\ꢀVSHFLDOꢀLQFLGHQWDOꢀRUꢀFRQVHTXHQWLDOꢀGDPDJHꢄꢀLQFOXGLQJꢀORVWꢀSUR¿WVꢍꢀ7KHUHꢀDUHꢀQRꢀZDUUDQWLHVꢀH[WHQGHGꢀRWKHUꢀWKDQꢀDVꢀSURYLGHGꢀKHUHLQꢍꢀ  
7KLVꢀOLPLWHGꢀZDUUDQW\ꢀPD\ꢀEHꢀPRGL¿HGꢀRQO\ꢀE\ꢀ(&+2ꢍ  
99922201032  
11/18/2011  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GRASS TRIMMER/BRUSH CUTTER  
OPERATOR'S MANUAL  
35  
NOTES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-2 SUEHIROCHO 1-CHOME, OHME, TOKYO, 198-8760, JAPAN  
PHONE: 81-428-32-6118 FAX: 81-428-32-6145  
ECHO, INCORPORATED  
400 OAKWOOD ROAD  
LAKE ZURICH, IL 60047-1564  
S05403001001/S05403999999  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Elation Professional Network Router RMD 1220 User Manual
Exido Hot Beverage Maker 245 065 User Manual
Fluke Weather Radio 845AR User Manual
Frigidaire Freezer FPUH17D7K User Manual
Fujitsu Automobile Accessories V5505 User Manual
Garland Food Warmer ED 15THSE User Manual
Gefen Switch EXT DPKVM 241 User Manual
GE Monogram Gas Grill Professional Outdoor Grills and Cooktop User Manual
GE Range 49 8255 User Manual
GE Refrigerator 200D8074P039 User Manual