Owner’s Manual
Front
Rear
Oven
surface
oven
GE Quality Product
Part No. 164D3333P184 184-6C097 Pub. No. 49-8954-1 02-01 JR
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
SafeyIructions
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire or
explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
OpeagIructions
WARNING ANTI-TIP DEVICE
All ranges can tip and injury could result.
To prevent accidental tipping of the range, attach it to the floor by installing the Anti-Tip device
supplied.
The device engages one of the rear leveling legs (see Installation Instructions).
To check if the device is installed properly, carefully tip the range forward.
If you pull the range out from the wall for any reason, make sure the rear leg is returned to its
position in the device when you push the range back.
rdCleaing
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
■Use this appliance only for its intended use ■CAUTION: ITEMS OF INTEREST TO
laIructions
as described in this manual.
CHILDREN SHOULD NOT BE STORED
IN CABINETS ABOVE A RANGE OR
ON THE BACKSPLASH OF A RANGE—
CHILDREN CLIMBING ON THE
RANGE TO REACH ITEMS COULD
BE SERIOUSLY INJURED.
■Be sure your appliance is properly installed
and grounded by a qualified technician in
accordance with the provided installation
instructions.
■Don’t attempt to repair or replace any
part of your range unless it is specifically
recommended in this manual. All other
servicing should be referred to a qualified
technician.
■Never wear loose-fitting or hanging
garments while using the appliance.
Flammable material could be ignited if
brought in contact with hot heating
elements and may cause severe burns.
T
rubleshotingT
■Before performing any service,
DISCONNECT THE RANGE POWER
SUPPLY AT THE HOUSEHOLD
DISTRIBUTION PANEL BY REMOVING
THE FUSE OR SWITCHING OFF THE
CIRCUIT BREAKER.
■Use only dry pot holders—moist or damp
pot holders on hot surfaces may result in
burns from steam. Do not let pot holders
touch hot heating elements. Do not use a
towel or other bulky cloth.
ips
■For your safety, never use your appliance
for warming or heating the room.
■Do not leave children alone—children
should not be left alone or unattended in
an area where an appliance is in use. They
should never be allowed to sit or stand on
any part of the appliance.
CustomSrvice
■Storage in or on appliance—Flammable
materials should not be stored in an oven
or near surface units.
■Don’t allow anyone to climb, stand or hang
on the door or range top. They could
damage the range and even tip it over,
causing severe personal injury.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
SAFETY PRECAUTIONS
SafeyIructions
■Keep hood and grease filters clean to
maintain good venting and to avoid
grease fires.
■Do not touch heating elements or interior
surface of oven. These surfaces may be hot
enough to burn even though they are dark
in color. During and after use, do not
touch, or let clothing or other flammable
materials contact surface units, areas
nearby surface units or any interior area
of the oven; allow sufficient time for
cooling first.
■Potentially hot surfaces include the
cooktop and areas facing the cooktop,
oven vent opening and surfaces near the
opening, and crevices around the oven
door. Remember: The inside surface of the
oven may be hot when the door is opened.
■Do not let cooking grease or other
flammable materials accumulate in or
near the range.
■Do not use water on grease fires. Never pick
up a flaming pan. Smother flaming pan on
surface unit by covering pan completely
with well-fitting lid, cookie sheet or flat tray.
Flaming grease outside a pan can be put
out by covering with baking soda or, if
available, a multi-purpose dry chemical or
foam type fire extinguisher.
OpeagIructions
COOK MEAT AND POULTRY THOROUGHLY…
rdCleaing
Cook meat and poultry thoroughly—meat to at least an INTERNAL temperature of 160°F. and poultry
to at least an INTERNAL temperature of 180°F. Cooking to these temperatures usually protects against
foodborne illness.
OVEN
Stand away from range when opening oven door. Hot air or steam which escapes can cause burns
to hands, face and/or eyes.
laIructions
■Don’t heat unopened food containers in
the oven. Pressure could build up and the
container could burst, causing an injury.
■Pulling out shelf to the shelf stop is a
convenience in lifting heavy foods. It is also
a precaution against burns from touching
hot surfaces of the door or oven walls.
ips
■Keep oven free from grease buildup.
■When using cooking or roasting bags in
oven, follow the manufacturer’s directions.
■Do not use your oven to dry newspapers.
If overheated, they can catch fire.
■Place oven shelf in desired position while
oven is cool. If shelves must be handled
when hot, do not let pot holder contact
heating units in the oven.
rubleshotingT
T
CustomSrvice
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SafeyIructions
SURFACE COOKING UNITS
Use proper pan size—This appliance is equipped with one or more surface units of different size.
Select cookware having flat bottoms large enough to cover the surface unit heating element. The use
of undersized cookware will expose a portion of the heating element to direct contact and may result
in ignition of clothing. Proper relationship of cookware to burner will also improve efficiency.
OpeagIructions
■Never leave surface units unattended at
high heat settings. Boilover causes smoking
and greasy spillovers that may catch on fire.
■Don’t immerse or soak removable surface
units. Don’t put them in a dishwasher.
■When flaming foods under the hood,
■Be sure drip pans are in place. Their
absence during cooking could damage
range parts and wiring.
■Don’t use aluminum foil to line drip
pans or anywhere in the oven except as
described in this guide. Misuse could
result in a shock, fire hazard or damage
to the range.
turn the fan on.
■Foods for frying should be as dry as
possible. Frost on frozen foods or moisture
on fresh foods can cause hot fat to bubble
up and over sides of pan.
■Use little fat for effective shallow or deep-
fat frying. Filling the pan too full of fat can
cause spillovers when food is added.
rdCleaing
■Only certain types of glass, glass/ceramic,
earthenware or other glazed containers are
suitable for range-top service; others may
break because of the sudden change in
temperature.
■To minimize the possibility of burns,
ignition of flammable materials, and
spillage, the handle of a container should
be turned toward the center of the range
without extending over nearby surface units.
■If a combination of oils or fats will be used
in frying, stir together before heating, or as
fats melt slowly.
■Always heat fat slowly, and watch as it heats.
laIructions
■Use deep fat thermometer whenever
possible to prevent overheating fat beyond
the smoking point.
■Always turn surface unit to OFF before
removing cookware.
■Keep an eye on foods being fried at HI or
MEDIUM HIGH heats.
T
rubleshotingT
■To avoid the possibility of a burn or electric
shock, always be certain that the controls
for all surface units are at OFF position and
all coils are cool before attempting to lift or
remove the unit.
ips
Read and follow this Safety Information carefully.
CustomSrvice
SAVE THESE INSTRUCTIONS
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the surface units.
Throughout this manual, features and appearance may vary from your model.
Surface Cooking Controls
Your surface units and controls are designed
to give you a variety of heat settings for surface
unit cooking.
In a quiet kitchen, you may hear slight
clicking sounds during cooking,
indicating heat settings selected are being
maintained.
SafeyIructions
At both OFF and HI positions, there is a
slight niche so control clicks at those
positions; HI marks the highest setting;
LO, the lowest setting.
Switching heats to higher settings always
shows a quicker change than switching to
lower settings.
How to Set the Controls
Push the control knob in.
When control is in any position other than
OpeagIructions
OFF, you can turn it without pushing in.
Turn either clockwise or
counterclockwise to desired
heat setting.
Be sure you turn control to OFF when
you finish cooking. An indicator light
will glow when ANY heat on any surface
unit is on.
Control must be pushed in to set only
from the OFF position.
Heat Setting Guide
rdCleaing
HI—Quick start for cooking; bring water
to boil.
LO—Cook after starting at HI; cook with
little water in covered pan.
MEDIUM HIGH—Fast fry, pan broil;
maintain fast boil on large amount
of food.
NOTE:
At HI or MEDIUM HIGH, never leave
food unattended. Boilovers cause
smoking; greasy spillovers may
catch fire.
Medium high
Medium low
MED—Saute and brown; maintain slow
boil on large amount of food.
MEDIUM LOW—Steam rice, cereal;
maintain serving temperature of
most foods.
At MEDIUM LOW or LO, melt
chocolate, butter on small unit.
laIructions
ips
Cooking Tips
■Use medium- or heavy-weight
cookware. Aluminum cookware
conducts heat faster than other
metals. Cast-iron and coated cast-iron
cookware is slow to absorb heat,
but generally cooks evenly at low or
medium heat settings. Steel pans may
cook unevenly if not combined with
other metals.
■To conserve the most cooking energy,
pans should be flat on the bottom,
have straight sides and tight fitting
lids. Match the size of the saucepan
to the size of the surface unit. A pan
that extends more than an inch
beyond the edge of the drip pan
traps heat, which causes “crazing”
(fine hairline cracks) on porcelain,
and discoloration ranging from blue
to dark gray on chrome drip pans.
rubleshotingT
T
■Do not overfill cookware with fat
that may spill over when adding food.
Frosty foods bubble vigorously. Watch
foods frying at high temperatures.
Keep range and hood clean from
accumulated grease.
CustomSrvice
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SafeyIructions
Using the oven.
The OVEN TEMP knob is located on the control panel on the front of the range.
Oven Temperature Control
To use the oven, simply turn the knob to
the desired cooking temperatures, which
are marked in 25°F. increments on the
dial. OVEN TEMP maintains the
The Oven Cycling Light glows until the oven
reaches your selected temperature, then goes off
and on with the oven unit(s) during cooking.
OpeagIructions
temperature you set, from WM (170°F.)
to BROIL (550°F.).
Bump
Oven Shelves
The shelves are designed with stop-locks
so when placed correctly on the shelf
supports, they will stop before coming
completely out of the oven and will not
tilt when you are removing food from
them or placing food on them.
To remove the shelves from the oven, pull
them toward you, tilt front end upward
and pull them out.
rdCleaing
To replace, place shelf on shelf support
with stop-locks (curved extension of
shelf) facing up and toward back of oven.
Tilt up front and push shelf toward back
of oven until it goes past the bump on the
shelf support. Then lower front of shelf
and push it all the way back.
When placing cookware on a shelf, pull
the shelf out to the bump on the shelf
support. Place the cookware on the
shelf, then slide the shelf back into the
oven. This will eliminate reaching into
the hot oven.
laIructions
Oven Shelf Positions
The oven has four shelf supports—A
(bottom), B, C and D (top).
Shelf positions for cooking are suggested
on Baking and Roasting pages.
T
rubleshotingT
The oven has 4 shelf positions.
The type of margarine will affect baking performance!
ips
Most recipes for baking have been developed
using high fat products such as butter or
margarine (80% fat). If you decrease the fat, the
recipe may not give the same results as with a
higher fat product.
Federal standards require products
labeled “margarine” to contain at least
80% fat by weight. Low fat spreads, on
the other hand, contain less fat and more
water. The high moisture content of these
spreads affects the texture and flavor of
CustomSrvice
Recipe failure can result if cakes, pies,
pastries, cookies or candies are made with baked goods. For best results with your
low fat spreads. The lower the fat content
of a spread product, the more noticeable
these differences become.
old favorite recipes, use margarine,
butter or stick spreads containing at
least 70% vegetable oil.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the oven for baking or roasting.
To avoid possible burns, place the shelves in the desired position before you turn the oven on.
How to Set Your Oven for Baking or Roasting
Position the shelf or shelves in the
oven. If cooking on two shelves at the
same time, stagger the pans for best
heat circulation.
Place food in oven on center of shelf.
SafeyIructions
Allow at least 2 inches between edge
of bakeware and oven wall or
adjacent cookware.
Close oven door. Turn OVEN TEMP
knob clockwise to desired temperature.
Preheat oven for at least 10 minutes
if preheating is necessary.
Check food for doneness at
minimum time on recipe. Cook
longer if necessary. Turn OVEN TEMP
knob to OFF and remove food.
Shelf Positions
OpeagIructions
■Most baking is done on the second
shelf position (B) from the bottom.
■Bake angel food cakes on first shelf
position (A) from bottom of oven.
■When baking three or four items, use
two shelves positioned on the second
and fourth sets of supports (B & D)
from bottom of oven.
■Roasting is usually done on the bottom
shelf position (A).
rdCleaing
Preheating
■Preheating the oven takes about 10
minutes.
■Most roasts will cook satisfactorily
without preheating.
■Preheat the oven only when necessary,
usually for baking.
■If you find preheating is necessary,
keep an eye on the indicator light and
put food in the oven promptly after
light goes out.
Baking and Roasting Tips
laIructions
■Follow a tested recipe and measure the
ingredients carefully. If you are using a
package mix, follow label directions.
■Frozen roasts of beef, pork, lamb, etc.,
can be started without thawing, but
allow 10 to 25 minutes per pound
additional time (10 minutes per pound
for roasts under 5 pounds, more time
for larger roasts).
ips
■Do not open the oven door during
a baking operation—heat will be lost
and the baking time might need to
be extended. This could cause poor
baking results. If you must open the
door, open it partially—only 3 or
4 inches—and close it as quickly
as possible.
■Thaw most frozen poultry before
roasting to ensure even doneness.
Some commercial frozen poultry
can be cooked successfully without
thawing. Follow directions given on
package label.
VERY IMPORTANT NOTE:
rubleshotingT
When baking or roasting, NEVER
turn the OVEN TEMP knob to
BROIL and back to the desired
temperature. Turning the OVEN
TEMP knob to BROIL sets the
thermostat in a BROIL mode. See
the Broiling section in this guide.
To reset the thermostat to Bake,
turn the OVEN TEMP knob to OFF
then back to the desired
T
■Roasting is cooking by dry heat.
Tender meat or poultry can be roasted
uncovered in your oven. Roasting
temperatures, which should be low and
steady, keep spattering to a minimum.
When roasting, it is not necessary to sear,
baste, cover or add water to your meat.
Bake/Roast temperature.
CustomSrvice
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SafeyIructions
Using the oven for broiling.
Broiling may be slightly different from any previous broiling you may be acquainted with, so be sure to read this
section completely.
How to Set Your Oven for Broiling
Broiling is cooking food by intense radiant heat
from the upper element in the oven. Most fish
and tender cuts of meat can be broiled. Follow
these steps to keep spattering and smoking to
a minimum.
Close the door. Always broil with the
door closed.
VERY IMPORTANT NOTE:
To reset the oven for Baking you
must turn the OVEN TEMP knob to
OFF. This gets it out of the BROIL
mode.
OpeagIructions
Turn the OVEN TEMP knob
clockwise to BROIL. You will feel
a slight niche at the broil position.
You may then turn the knob
counterclockwise to broil at a
lower temperature.
If the meat has fat or gristle around
the edge, cut vertical slashes through
both about 2″ apart. If desired, fat
may be trimmed, leaving layer about
1/8″ thick.
Turn food only once during
cooking.
Place the meat on the broiler grid in
the broiler pan which comes with
your range. Always use the grid so
the fat drips into the broiler pan;
otherwise the juices may become hot
enough to catch fire.
Turn the OVEN TEMP knob to OFF.
Serve food immediately, and leave
the pan outside the oven to cool
during the meal for easiest cleaning.
rdCleaing
Place the shelf in position C for most
broiling.
Use of Aluminum Foil
laIructions
■You can use aluminum foil to line your
broiler pan and broiler grid. However,
you must mold the foil tightly to the
grid and cut slits in it just like the grid.
■DO NOT place a sheet of aluminum foil
on the shelf. To do so may result in
improperly cooked foods, damage to
oven finish and increase in heat on
outside surfaces of the oven.
■Without the slits, the foil will prevent
fat and meat juices from draining to the ■If desired, a sheet of aluminum foil may
broiler pan. The juices could become
hot enough to catch on fire. If you do
not cut the slits, you are frying, not
broiling.
be used on floor of the oven under the
bake element. Be certain foil does not
touch bake element. Aluminum foil
used in this way may slightly affect the
browning of some foods. Change foil
when it becomes soiled.
T
rubleshotingT
ips
CustomSrvice
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the oven for broiling.
Questions and Answers
When broiling, is it necessary to
always use a grid in the pan?
Why are my meats not turning out as
brown as they should?
SafeyIructions
Yes. Using the grid suspends the
meat over the pan. As the meat
cooks, the juices fall into the pan,
thus keeping meat drier. Juices are
protected by the grid and stay cooler,
thus preventing excessive spatter and
smoking.
In some areas, the power (voltage) to
the range may be low. In these cases,
preheat the broil element for 10
minutes before placing broiler pan
with food in oven. Check to see if you
are using the recommended shelf
position. Broil for longest period of
time indicated in the Broiling Guide.
Turn food only once during broiling.
Should I salt the meat before
broiling?
OpeagIructions
Do I need to grease my broiler grid
to prevent meat from sticking?
No. Salt draws out the juices and
allows them to evaporate. Always salt
after cooking. Turn meat with tongs;
piercing meat with a fork also allows
juices to escape. When broiling
poultry or fish, brush each side often
with butter.
Yes. The broiler grid is designed to
absorb broiler heat. Spraying the
broiler grid lightly with a vegetable
cooking spray before cooking will
make cleanup easier.
rdCleaing
Broiling Guide
■If desired, marinate meats or chicken
before broiling, or brush with barbecue
sauce last 5 to 10 minutes only.
■When arranging food on pan, do not
let fatty edges hang over sides because
the dripping fat will soil the oven.
■Frozen steaks can be broiled by
positioning the oven shelf at next
lowest shelf position and increasing
■If your range is connected to 208
volts, rare steaks may be broiled by
preheating the broiler and positioning
the oven shelf one position higher.
1
cooking time given in this guide 1 ⁄2
times per side.
laIructions
Amount or
Thickness
Shelf
Time In Minutes
Food
Position First Side Second Side Comments
Bacon
1/2 lb.
(about 8 thin slices)
C
31⁄2 min.
31⁄2 min.
Arrange in single layer
ips
Ground Beef
1 lb. (4 patties)
1/2 to 3/4″ thick
C
7 min.
5 min.
Space evenly.
Beef Steaks
Medium
1″ thick
C
9 min.
9 min.
Steaks less than 1″
thick cook through
before browning. Pan
frying is recommended.
Slash fat.
1 to 11⁄2 lbs.
rubleshotingT
T
Chicken
Fish
1 whole
A
35 min.
15 min.
Reduce time about 5
to 10 minutes per side
for cut-up chicken.
Brush each side with
melted butter. Broil
skin-side-down first.
Handle and turn very
carefully. Brush with
lemon butter before
and during cooking,
if desired. Preheat
broiler to increase
browning.
2 to 21⁄2 lbs.,
split lengthwise
1 lb. fillets
1/4 to 1/2″ thick
C
5 min.
5 min.
CustomSrvice
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SafeyIructions
Care and cleaning of the range.
Be sure electrical power is off and all surfaces are cool before cleaning any part of the range.
Proper care and cleaning are important so your range will give you efficient and satisfactory service. Follow these
directions carefully in caring for your range to assure safe and proper maintenance.
If your range is removed for cleaning, servicing or any reason, be sure the anti-tip
device is re-engaged properly when the range is replaced. Failure to take this
precaution could result in tipping of the range and cause injury.
OpeagIructions
Porcelain Enamel Cooktop
The porcelain enamel finish is sturdy but
breakable if misused. This finish is acid-
resistant. However, any acidic foods
spilled (such as fruit juices, tomato or
vinegar) should not be permitted to
remain on the finish.
rdCleaing
Oven Shelves
Clean the shelves with an abrasive
cleanser or steel wool.
After cleaning, rinse the shelves with
clean water and dry with a clean cloth.
laIructions
Surface unit
Surface Units and Drip Pans
To clean the surface units, turn the
control to the highest setting for a
minute. The coils will burn off any soil.
To clean the drip pans:
Drip pans can be cleaned in the
dishwasher or by hand. If you use a
scouring pad, rub lightly to prevent
scratching.
To remove a surface unit:
Drip pan
Receptacle
To remove the drip pans for cleaning,
the surface units must be removed first.
Can I cover the drip pans with foil?
To remove the surface unit, lift it
about 1 inch above the drip pan
and pull it out.
Lift the surface unit about 1 inch above
the drip pan and pull it out.
No, because using foil so close to the
receptacle could cause shock, fire or
damage to the range.
T
rubleshotingT
Do not lift the surface unit more than 1 inch. If
you do, it may not lie flat on the drip pan when
you plug it back in.
CAUTION:
■Do not immerse the surface units in
NOTE: Repeated lifting of the surface unit
more than 1 inch above the drip pan can
permanently damage the receptacle.
liquids of any kind.
■Do not clean the surface units in a
dishwasher.
ips
Replace the drip pan into the
recess in the cooktop.
To replace a surface unit:
■Do not bend the surface unit plug
Replace the drip pan into the recess in
the cooktop. Make sure the opening in
the pan lines up with the receptacle.
terminals.
CustomSrvice
■Do not attempt to clean, adjust or in
any way repair the plug-in receptacle.
Insert the terminals of the surface unit
through the opening in the drip pan and
into the receptacle.
Guide the surface unit into place so it
rests evenly.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and cleaning of the range.
Lift-Off Oven Door (on some models)
The oven door is removable (on some
models) but it is heavy. You may need
help removing and replacing the door.
To replace the door:
Position the slots in the bottom of
SafeyIructions
the door squarely over the hinges.
Then lower the door slowly and
evenly over both hinges at the
same time.
To remove the door:
Open the door to the full open
position.
Open the door to the full open
position and press the locking
mechanism back into its original
position.
Raise the locking mechanism by
applying force to the locking
mechanism lever.
Locking mechanism lever
Close the door until it stops against
the locking mechanism.
DO NOT ATTEMPT TO CLOSE THE DOOR
UNTIL THIS STEP IS COMPLETE. THE
HINGE OR DOOR COULD BE DAMAGED.
OpeagIructions
To lock
apply force
Grasp firmly on each side and lift the
door straight up and off the hinges.
rdCleaing
To unlock apply force
Oven Heating Elements
Do not clean the bake element or the
broil element. Any soil will burn off when
the elements are heated.
The bake element can be lifted gently to
clean the oven floor. If spillovers, residue
or ash accumulate around the bake
element gently wipe around the element
with warm water.
laIructions
ips
Broiler Pan and Grid
After broiling, remove the broiler pan
If food has burned on, sprinkle the grid
from the oven. Remove the grid from the with detergent while hot and cover with
pan. Carefully pour out grease from the
pan into a proper container. Wash and
rinse the broiler pan and grid in hot water
with a soap-filled or plastic scouring pad.
wet paper towels or a dishcloth. Soaking
the pan will remove burned on foods.
rubleshotingT
T
Do not store a soiled broiler pan and grid
anywhere in the range.
Both the broiler pan and grid can
also be cleaned in the dishwasher.
CustomSrvice
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SafeyIructions
Control Knobs
The control knobs may be removed for easier
cleaning.
To remove a knob, pull it straight off the
stem.
Before removing the knobs for cleaning,
please note that the knobs are in the
proper OFF position. When replacing the
knobs, check the OFF position to insure
proper placement.
Wash the knobs in soap and water but do
not soak. Avoid getting water down in the
knob stem holes.
OpeagIructions
Painted Surfaces
Painted surfaces include the sides and
kick panel. Clean these with soap and
water or a vinegar and water solution.
rdCleaing
Do not use commercial oven cleaners, cleansing
powders, steel wool or harsh abrasives on any
painted surface.
Porcelain Oven Interior
With proper care, the porcelain enamel interior
will retain its attractive finish for many years.
Cautions about using spray-on oven
cleaners:
laIructions
Soap and water will normally do the job.
Heavy spattering or spillovers may
■Do not spray the oven cleaner on the
electrical controls and switches because
it could cause a short circuit and result
in sparking or fire.
require cleaning with a mild abrasive
cleanser. Soapy, wet pads may also be
used. Do not allow food spills with a high
sugar or acid content (such as milk,
tomatoes, sauerkraut, fruit juices or pie
filling) to remain on the surface. They
may cause dull spots even after cleaning.
■Do not allow a film from the cleaner
to remain on the temperature sensor—
it could cause the oven to heat
improperly. (The sensor is located at
the top of the oven.) Carefully wipe the
bulb clean after each oven cleaning,
being careful not to move the sensor
as a change in its position could affect
how the oven bakes.
Household ammonia may make the
cleaning job easier. Place 1/2 cup
ammonia in a shallow glass pan and leave
in a cold oven overnight. The ammonia
fumes will help loosen the burned-on
grease and food.
T
rubleshotingT
■Do not spray any oven cleaner on the
outside oven door, handles or any
exterior surface of the oven, cabinet
or painted surfaces. The cleaner can
damage these surfaces.
When necessary, you may use a
commercial oven cleaner. Follow the
package directions.
ips
CustomSrvice
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation of the range.
Read these instructions completely and carefully.
WARNING!
Anti-Tip Bracket
• ALL RANGES CAN TIP
• INJURY COULD RESULT
SafeyIructions
• INSTALL ANTI-TIP DEVICE
PACKED WITH RANGE
• SEE INSTRUCTIONS
OpeagIructions
Tools You Will Need
■Phillips head screwdriver
■13⁄8″ or adjustable wrench
■Flat blade screwdriver
rdCleaing
Anti-Tip Bracket Installation Instructions
Anti-tip bracket attaches to the floor to hold either rear
range leg. When fastening to the floor, be sure that the
screw does not penetrate electrical wiring or plumbing. If
you cannot be sure of this, use a shorter screw that will not
penetrate through the flooring.
Screw the bracket securely to the floor with
the screw provided. The screw is self-drilling
in wood, plywood, particle and chip board,
and most metal framing. If attaching to
masonry, you can buy suitable screws and/or
anchors at hardware stores. Use a masonry
drill to drill the required holes.
Decide whether the anti-tip bracket will be
installed on the right or left side of the range
location.
laIructions
Wall
Anti-tip bracket
If the bracket side of the range is next to a
cabinet, place the bracket against back wall
and cabinet.
ips
If there is no adjacent cabinet, determine
where the location of the range side (painted
outside panel) will be. Place the bracket with
its outside edge at this location and against
the back wall.
Using the wrench, back out the four range
legs at least two turns. Level the range. See
the Protect Your Floor and Leveling the Range
information in the Installation the range
section of this manual for leveling
information.
rubleshotingT
Outside edge of bracket
should be flush with the
outside of the range
T
Wall behind range
Adjacent cabinet
or final location
of range side panel
Slide the range into place.
CustomSrvice
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SafeyIructions
Read these instructions completely and carefully.
Electrical Connection
We recommend that you have the electrical hookup of your
If you fail to wire your range in accordance with
governing codes, you may create a hazardous
condition.
range done by a qualified electrician. Have the electrician
show you where your range disconnect is located.
OpeagIructions
Call your Electric Company and ask which codes
apply in your area. If there are no codes, you must
follow the NATIONAL ELECTRICAL CODE,
ANSI/NFPA NO. 70, latest edition. You can get a
copy by writing:
You must use a three-wire, single-phase AC
208/240 Volt, 60 Hertz electrical system to
operate your range.
Use #8 wire and 40 Amp fuse or circuit breaker
for 240 Volt and 208 Volt systems.
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
Do not use aluminum wiring to connect your
range to the household circuit.
rdCleaing
To Make Electrical Connection
Remove the junction block access cover
(on range back).
Use a range cord rated at 40 amps with 125/250
minimum volt range and closed loop terminals.
Care should be taken to center cable and strain
relief within knockout hole to keep the edge from
damaging the cable.
Effective January 1, 1996 the National
Electrical Code requires that new construction
(not existing) utilize a 4-conductor connection
to an electric range.
NOTE: A 4-conductor cord is to be used when the
appliance is installed in a mobile home or when
local codes do not permit grounding through the
neutral.
laIructions
Use only 3-conductor or 4-conductor U.L. listed
range cord. You must use the strain relief clamp
provided with the range to hold the cord.
Hard Wiring
The power cord bracket also incorporates a 7/8″
diameter opening for hard wiring (armored
cable, flexible conduit, romex wire, etc.).
T
rubleshotingT
If this type of wire is used, remove the strain relief
clamp and bracket and reposition the bracket so
the 7/8″ diameter hole is at the bottom to accept
the hard wiring.
ips
CustomSrvice
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation of the range.
Read these instructions completely and carefully.
Three-Wire Cord Connection
SafeyIructions
If local codes require an ungrounded neutral:
Junction block
on range back
Follow steps 1 through 5.
Black
Red
Junction block
on range back
Black
Top nut
Red
Ground
strap
White lead
Red lead
Ground wire
White lead
Top nut
Black lead
OpeagIructions
Ground
strap
Black lead
Strain relief
clamp
Red lead
Remove the top nuts on the junction
block studs.
Strain relief
clamp
Tighten the back nuts.
Then loosen the screw from the ground strap and
fasten a #10 copper wire to the range. Secure the
other end of the wire to a grounded cold water
pipe or use another approved grounding
method.
Install the three wire cord and the strain
relief in the hole in the strain relief bracket.
rdCleaing
Connect the red and black leads to the
outer terminals and the white lead to the
center terminal.
Push the cord upward (to relieve strain),
while tightening the strain relief clamp.
Four-Wire Cord Connection
laIructions
Remove the top nuts on the junction
block studs.
Red
ips
Black
Tighten the back nuts.
Remove the ground screw; then remove
the ground strap.
Ground strap
removed
Install the four wire cord and strain relief in
the hole in the strain relief bracket.
Black lead
rubleshotingT
T
Connect the red and black leads to the
outside terminals and the white lead to the
center terminal.
Green lead
Red lead
Ground
screw
White lead
Attach the green lead below the junction
block with the ground screw that was
removed earlier (step 3).
Push the strain relief upward (to relieve
strain) while tightening the strain relief
clamp.
CustomSrvice
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SafeyIructions
Read these instructions completely and carefully.
Dimensions and Clearances
■To eliminate the risk of burns or fire when
reaching over hot surface elements, cabinet
storage space above the cooktop should be
avoided. If cabinet storage space is to be
provided above the cooktop, the risk can be
reduced by installing a range hood that sticks
out at least 5″ beyond the front of the cabinets.
Cabinets installed above a cooktop may be no
deeper than 13″.
IMPORTANT: Save these instructions for the
local electrical inspector’s use.
OpeagIructions
■See the illustration below for all rough-in and
spacing dimensions. These dimensions must be
met for safe use of your range.
■The range may be placed with 13⁄4″ clearance at
the back wall and 0″ clearance (flush) at side
walls of the range if the front edges of the range
side panels stick out beyond the cabinet fronts
at least 1/4″.
B
rdCleaing
From combustible
walls above cooking
surface
13″ max.
30″
18″ min.
2″
21⁄2″
C
251⁄2″ from
24″
wall to front
of control
panel
A
laIructions
5″
34″
5″
401⁄2″
Front
Rear
Oven
surface
oven
5″
36″
max.
36″
Flush
mount
outlet
T
Surface
mount
outlet
51⁄4″
rubleshotingT
From bottom
of range to
strain relief
clamp
Models
A
B
C
24″
401⁄4″
20″ Wide
24″ Wide
20″
24″
203⁄8″
24 3⁄8″
2″
0″
ips
*Depth including handle: 259⁄16″.
*Depth to front of control knobs: 261⁄8″.
CustomSrvice
Preparation
■Remove all tape and packaging.
■Take the accessory pack out of the oven.
■Check to be sure that no range parts have come
loose during shipping.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation of the range.
Read these instructions completely and carefully.
Protect Your Floor
SafeyIructions
Your range, like many other household items, is
The range should be installed on a sheet of
heavy and can settle into soft floor coverings such as plywood (or similar material) as follows: When
cushioned vinyl or carpeting. When moving the
range on this type of flooring, use care, and it is
recommended that these simple and inexpensive
instructions be followed.
the floor covering ends at the front of the range,
the area that the range will rest on should be built
up with plywood to the same level or higher than
the floor covering. This will allow the range to be
moved for cleaning or servicing.
Installing the Backguard
OpeagIructions
Place the backguard on top of the end panels
at the rear of the range.
rdCleaing
Insert two machine screws through the holes
at the bottom of each end cap. Secure the
screws to the range frame with the hex nuts
provided.
laIructions
ips
Insert two machine screws through the front
of the backguard at each end. Secure the
screws to the range frame with the hex nuts
provided.
rubleshotingT
T
CustomSrvice
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SafeyIructions
Read these instructions completely and carefully.
Leveling the Range
For proper cooking and baking the range must be
leveled. Leveling legs are located on each corner
at the base of the range.
OpeagIructions
rdCleaing
Install the oven shelves (see use and care section
for instructions). Put a spirit level or a glass
measuring cup partially filled with water on
one of the oven shelves.
laIructions
Use a 13⁄8″ open end wrench or an adjustable
wrench to back out the four leveling legs two
or three turns each. Now use the wrench to adjust
the leveling legs until the range is level.
Slide range back towards the wall being careful
not to damage the sides or top of the range,
or the adjacent cabinets.
T
rubleshotingT
ips
CustomSrvice
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Call For Service…
Troubleshooting Tips
Save time and money! Review the chart on this page
first and you may not need to call for service.
SafeyIructions
Problem
Possible Causes
What To Do
Surface units not
functioning properly
The surface units are
not plugged in solidly.
• With the controls off, check to make sure the surface
unit is plugged completely into the receptacle.
The surface unit controls
improperly set.
• Check to see the correct control is set for the surface
unit you are using.
The drip pans are not set
securely in the cooktop.
• With the controls off, check to make sure the drip
pan is in the recess in the cooktop and that the
opening in the pan lines up with the receptacle.
OpeagIructions
Oven will
not work
A fuse in your home may
be blown or the circuit
breaker tripped.
• Replace the fuse or reset the circuit breaker.
Plug on range is not
completely inserted in
the electrical outlet.
• Make sure electrical plug is plugged into a live, properly
grounded outlet.
Oven control
improperly set.
• See the Using the oven sections.
rdCleaing
Food does not
broil properly
Oven control
improperly set.
• Make sure you turn the knob all the way to the
BROIL position.
Improper shelf position
being used.
• See the Broiling Guide.
Cookware not suited
for broiling.
• Use the broiling pan and grid that came with your range.
• See the Using the oven for broiling section.
Aluminum foil used on the
the broiling pan and grid has
not been fitted properly and
slit as recommended.
laIructions
Food does not bake
or roast properly
Oven control
improperly set.
• See the Using the oven for baking or roasting section.
ips
OVEN TEMP knob was
turned to BROIL before
being set at a baking
temperature
• Turn the knob to OFF and then to the bake temperature.
Shelf position is incorrect
or the shelf is not level.
• See the Using the oven for baking or roasting section.
• See the Using the oven for baking or roasting section.
• See the Using the oven for baking or roasting section.
rubleshotingT
T
Necessary preheating
was not done.
Incorrect cookware or
cookware of improper
size being used.
A foil tent was not
used when needed
to slow down browning
during roasting.
• See the Using the oven for baking or roasting section.
CustomSrvice
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SafeyIructions
Notes.
OpeagIructions
rdCleaing
laIructions
T
rubleshotingT
ips
CustomSrvice
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes.
SafeyIructions
OpeagIructions
rdCleaing
laIructions
ips
rubleshotingT
T
CustomSrvice
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SafeyIructions
Electric Range Warranty.
All warranty service provided by our Factory Service Centers
®
or an authorized Customer Care technician. For service,
call 800-GE-CARES.
For The Period Of: We Will Replace, At No Charge To You:
OpeagIructions
One Year
From the date of the
original purchase
Any part of the range which fails due to a defect in materials or workmanship.
During this full one-year warranty, we will also provide, free of charge, all labor
and in-home service to replace the defective part.
What is Not Covered:
■Service trips to your home to teach you how to
use the product.
■Replacement of house fuses or resetting of circuit
breakers.
■Improper installation.
■Damage to the product caused by accident, fire,
rdCleaing
floods or acts of God.
■Failure of the product if it is abused, misused, or
used for other than the intended purpose or used
commercially.
■Incidental or consequential damage to personal
property caused by possible defects with this appliance.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for
home use within the USA. In Alaska, the warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty
gives you specific legal rights, and you may also have other rights which vary from state to state. To know
what your legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
laIructions
T
rubleshotingT
ips
Warrantor: General Electric Company. Louisville, KY 40225
CustomSrvice
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Support.
GE Appliances Website
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,
any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,
order parts, catalogs, or even schedule service on-line. You can also “Ask Our Team of Experts™”
your questions, and so much more...
Schedule Service
Expert GE repair service is only one step away from your door. Get on-line and schedule your service at
your convenience 24 hours any day of the year! Or call 800-GE-CARES (800-432-2737) during normal
business hours.
Real Life Design Studio
GE supports the Universal Design concept—products, services and environments that can be used by
people of all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and
mental abilities and impairments. For details of GE’s Universal Design applications, including kitchen
design ideas for people with disabilities, check out our Website today. For the hearing impaired, please call
800-TDD-GEAC (800-833-4322).
Extended Warranties
Purchase a GE extended warranty and learn about special discounts that are available while your warranty
is still in effect. You can purchase it on-line anytime, or call 800-626-2224 during normal business hours.
GE Consumer Home Services will still be there after your warranty expires.
Parts and Accessories
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes
(VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or by phone at
800-626-2002 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally
should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause
unsafe operation.
Contact Us
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details
including your phone number, or write to: General Manager, Customer Relations
GE Appliances, Appliance Park
Louisville, KY 40225
Register Your Appliance
Register your new appliance on-line—at your convenience! Timely product registration will allow for
enhanced communication and prompt service under the terms of your warranty, should the need arise.
You may also mail in the pre-printed registration card included in the packing material, or detach and
use the form in this Owner’s Manual.
Printed in the United States
Download from Www.Somanuals.com. All Manuals Search And Download.
|