GE Dishwasher 206C1559P148 User Manual

Installation  
Instructions  
Built-In  
Dishwasher  
BEFORE YOU BEGIN  
IMPORTANT The dishwasher  
MUST be installed to allow for future removal from  
the enclosure if service is required.  
Read these instructions completely and  
carefully .  
If you received a damaged dishwasher , you should  
immediately contact your dealer or builder .  
IMPORT ANT  
Observe all  
governing codes and ordinances.  
Note to Installer – Be sure to leave these instructions  
for the  
and  
Iinspectors use.  
local  
Note to Consumer Keep these instructions with your  
FOR YOUR SAFETY  
Owner`s Manual for future reference.  
Skill level  
basic mechanical ,Plumbing  
Read and observe all CAUTIONS and WARNINGS  
shown throughout these instructions. While performing  
installations described in this booklet, gloves, safety  
glasses or goggles should be worn.  
Installation of this dishwasher requires  
electrical skills. Proper  
and  
installation is the responsibility of the installer .  
Product failure due to improper installation is not  
covered under the  
Dishwasher Warranty  
Completion Time ? 1 to 3 Hours. New installations  
WARNING  
require more time than replacement installations.  
To reduce the risk of electrical shock, fire,  
or injury to persons, the installer must  
ensure that the dishwasher is completely  
enclosed at the time of installation.  
READ CAREFULLY.  
KEEP THESE INSTRUCTIONS.  
206C1559P148 31-30207 03-10 FL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Preparation  
PREPARE DISHW ASHER ENCLOSURE  
The dishwasher must be installed so that drain hose is  
no more than 10feet in length for proper drainage.  
The dishwasher must be fully enclosed on the top,  
sides and back, and must not support any part of the  
enclosure.  
32-1/2to 35"  
Underside of  
Countertop  
to Floor  
24"  
Countertop  
CLEARANCES: When  
installed into a corner,  
allow 2"min. clearance  
between dishwasher and  
adjacent cabinet, wall or  
other appliances. Allow  
25-5/8"min. clearance  
from the front of the  
dishwasher for door  
opening. Figure 2  
Min.  
4
Dishwasher  
Cabinets  
Square  
and  
6
25-5/8"  
Plumb  
ClearanceforDoor  
Opening2"Minimum  
Floor MUST  
be Even with  
Room Floor.  
Plumbing and Electric Service  
Must Enter Shaded Area  
Figure 1  
Figure 2  
Llation,  
Note:  
(32-1/2")  
by  
counter  
and  
The rough cabinet opening must be at least 24"deep  
tops may  
leveling legs.  
the  
and 23-5/8"To  
Wide. The opening should be  
24"  
to  
35"max. height.  
Method 1 Air Gap with Waste Tee or Disposer  
DRAIN REQUIREMENTS  
Follow local codes and ordinances.  
Do not exceed 10 feet distance to drain.  
Do not connect drain lines from other devices  
to the dishwasher drain hose.  
Dishwasher must be connected to waste line with an  
air gap (not supplied) or 32" minimum high drain loop,  
depending on local codes and ordinances to prevent  
back flow into the dishwasher .  
Figure 3  
?Air gap must be used if waste tee or disposer connec-  
tion is less than 18"above the floor to prevent siphoning.  
Method 2 High Drain with Waste Tee or Disposer  
Provide a method to attach drain hose to underside  
of countertop.  
DRAIN PREPARATION  
The type of drain installation depends on answers to  
the following questions:  
Do local codes or ordinances require an air gap?  
Will waste tee or disposer connection be less than  
18"above the floor?  
Will installation have a drain loop less than 32"  
above floor?  
If the answer to ANY of the 3 questions above is YES,  
Method 1 MUST be used . Otherwise either Method 1  
or Method 2 may be used. Figure 3 or Figure 4.  
32"  
Min.  
32"  
Min.  
18"  
18"  
Min.  
Min.  
18"  
Min.  
Figure 4  
Install waste tee or disposer and air gap according to  
mManufacturer instructions.  
s
CAUTION:  
CABINET PREPARATION  
An air gap MUST BE USED if the drain hose is connected  
to waste tee or disposer lower than 18"above the floor.  
Drill a 1-1/2 dia.Hole in the cabinet wall within the  
·
Failure to provide the proper drain connection height  
with air gap or 32" minimum, high drain loop will result  
in improper draining of the dishwasher .  
shaded areas shown in Figure 1 for the drain hose  
connection. The hole should be smooth with no sharp  
edges.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Preparation  
PREPARE ELECTRICAL WIRING  
W ARNING  
FOR PERSONAL SAFETY: Remove house  
fuse or open circuit breaker before  
beginning installation. Do not use an  
extension cord or adapter plug with this  
appliance.  
1-1/2" Dia.  
Hole (Max.)  
3"  
Electrical Requirements  
from  
This appliance must be supplied with 120V, 60Hz., and  
connected to an individual properly grounded branch  
circuit, protected by a 15 or 20 ampere circuit breaker  
or time delay fuse.  
Cabinet  
24"  
from Wall  
Wiring must be 2 wire with ground.  
Ground  
Black  
If the electrical supply does not meet the above  
requirements, call a licensed electrician before  
proceeding.  
Figure 5  
White  
Cabinet Preparation & Wire Routing  
The wiring may enter the opening from either side,  
rear or the floor within the shaded area.  
Grounding Instructions – Cable Direct  
This appliance must be connected to a grounded metal,  
permanent wiring system, or an equipment grounding  
conductor must be run with the circuit conductors and  
be connected to the equipment grounding terminal or  
lead on the appliance.  
Max.dia.hole to admit the electrical cable.  
Cut a 1-1/2  
The hole must be free of sharp edges. If the cabinet  
wall is metal, the hole edge must be covered with a  
bushing.  
Cable direct connections may pass through the same  
hole as the drain hose and hot water line, if convenient.  
If cabinet wall is metal, the hole edge must be covered  
with a bushing. NOTE: Power cords with plug must pass  
through a separate hole.  
Grounding Instructions – Power Cord Models  
This appliance must be grounded. In the event of a  
malfunction or breakdown, grounding will reduce the  
risk of electrical shock by providing a path of least  
resistance for electric current. The plug must be  
plugged into an appropriate outlet that is installed  
and grounded in accordance with local codes and  
ordinances.  
Electrical Connection to Dishwasher  
Electrical connection is on the right front of dishwasher .  
For cable direct connections the cable must be routed  
as shown in Figure 5. Cable must extend a minimum of  
24"from the rear wall.  
For power cord connections, install a 3-prong ground-ing  
type receptacle. The power-supply receptacle for the  
W ARNING  
The improper connection of the  
in  
appliance shall be installed  
a cabinet or on a  
equipment grounding conductor can  
result in a risk of electric shock. Check  
with a qualified electrician or service  
representative if you are in doubt that  
the appliance is properly grounded.  
wall adjacent to the undercounter space in which the  
appliance is to be installed.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Instructions  
BEFOR YOU BEGIN  
PREPARE HOT WATER LINE  
Locate and set aside the package containing  
The line may enter from Either side, rear or floor  
within the shaded area shown in Figure F.  
The line may pass through the same hole as the  
electrical cable and Drain hose. Or, Cut an additional  
1-1/2" dia. hole to accommodate the water line.  
If power cord with plug is used, water line Must not  
pass through power cord hole.  
Locate set aside  
2 phillips head countertop mounting screws  
2 Phillips  
screws  
and 2 additional toekickscrews(located in  
and 2  
in  
the literature).  
the literature package).  
CHECK DOOR BALANCE  
To check the door balance,hold the top of the dis-  
T
washer firmly.  
washer firmly.  
Figure 6  
W ater Line Connection  
Turn off the water supply.  
Figure G  
Figure  
Install a hand shut-off valve in an accessible location,  
such as under the sink. (Optional, but strongly recom-  
mended and may be required by local codes.)  
Water connection is on the left side of the dishwasher .  
Install the hot water inlet line, using no less than 3/8"  
O.D. copper tubing. Route the line as shown in Figure F  
and extend forward at least 18"from rear wall.  
7
Open the door slowly,if the door drops when  
·
?Open the door slowly, if the door drops when  
released,increase spring tension.If the door closes  
released, increase Spring tension. If the door closes  
when released,decrease tension.  
when released, decrease tension.  
Pull the spring adjustment pin out of the holes,insert  
?Pull  
pin  
of the  
·
in the next highest or lowest hole and test again.  
? Adjustbboothth door springs tothtehe same tension.  
in or  
·
Flush water line to clean out debris.  
The hot water supply line pressure must be 20-120PSI.  
?Continue  
the spring  
until door Is balanced.  
Continue moving the spring pin until door is balance.  
·
CAUTION:  
Opening the door will cause the dishwasher  
to tip forward. Do not open the door until you are ready  
to install the dishwasher . If it is  
necessary to open the door, hold  
the top of the dishwasher securely  
with one hand and hold the door  
with the other hand.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Instructions  
STEP 16 DISHWASHER WET TEST  
Turn on power supply(or plug power cord into outlet, if equipped).  
Select Normal wash program.  
Close the door.  
Check to be sure that water enters the dishwasher.If water does not enter the dishwasher,check to be sure that  
water and power are turn on.  
Check for leaks under the dishwasher.If a leak is found,turn power supply off,then tighten connections.Restore  
power afterleak is corrected.  
Check for leaks.around the door. A leak around the door could be caused by door rubbing or hitting against  
adjacent cabinetry. Reposition the dishwasher if necessary.See step 9.  
The dishwasher will drain and turn off about 5 to 7 minutes after the first fill.Check dain lines.If leaks are found,turn  
power off at the breaker and correct plumbing as necessary.Restore power ater corrections are made.See Step 12.  
Open dishwasher door and make sure most of the water has drained.If not ,check that disposer plug has been  
removed and/or air gap is not plugged.See Step 13.Also chek drain line for kinking.  
Run the dishwasher through another fill and drain cycle .Check for leaks and correct if require.  
At the end of drain, Press reset button.  
STEP 17 REPLACE TOEKICK  
2-Screws  
Adjust Up  
or Down  
Install 2 toekick screws to fasten toekick. Allow the toe kick to tuch the floor.  
·
STEP 18 LITERATURE  
Be sure to leave complete literature package and installation instructions with consumer.  
NOTE:The manufacturer,following a policy of constant development and up-dating of the product,may make  
modifications without giving prior notice.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Echo Blower PB 760 LN H T User Manual
ELAN Home Systems Speaker PSP6 User Manual
Faber Ventilation Hood 5x20 5A User Manual
Fisher Price Handheld Game System 71657 User Manual
Fluke Computer Monitor RPM4 User Manual
Fujioh Ventilation Hood FDK 03A User Manual
Fujitsu Printer FTP604 User Manual
GE Coffeemaker 169208 User Manual
Gemini Musical Instrument PS 650I User Manual
Gianni Industries Door EM NH600 User Manual