X7722271404 / X772000164
PB-760 LN H/T
Power Blower
Operator’s Manual
Burn Hazard
The muffler or catalytic muffler and surrounding cover may become extremely hot.
Always keep clear of exhaust and muffler area, otherwise serious personal injury may
occur.
The engine exhaust from this product contains chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
Users of this equipment risk injury to themselves and others if the unit is used
improperly and/or safety precautions are not followed. ECHO provides an operator’s
manual. It must be read and understood for proper and safe operation. Failure to do so
could result in serious injury.
Specifications, descriptions and illustrative material in this literature are as accurate as known at the time
of publication, but are subject to change without notice. Illustrations may include optional equipment and
accessories, and may not include all standard equipment.
X7531125002
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PB-760 LN H/T
INTRODUCTION
INTRODUCTION
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and
on-the-job dependability. Read and understand this manual. You will find it easy to use and full of helpful
operating tips and SAFETY messages.
The Operator’s Manual
Keep it in a safe place for future reference. Contains specifications and information for safety, operation,
maintenance, storage and assembly specific to this product.
SERVICING INFORMATION
Parts/Serial Number
Genuine ECHO Parts and ECHO REPOWER™ Parts and
Assemblies for your ECHO products are available only from an
Authorized ECHO Dealer. When you do need to buy parts always
have the Model Number and Serial Number of the unit with you. You
can find these numbers on the engine housing. For future reference,
write them in the space provided below.
Model No. _________________ SN. ___________________
Service
Service of this product during the warranty period must be performed by an Authorized ECHO Service
Dealer. For the name and address of the Authorized ECHO Service Dealer nearest you, ask your retailer or
call: 1-800-432-ECHO (3246). Dealer information is also available on our Web Site. When presenting your
unit for Warranty service/repairs, proof of purchase is required.
Echo Consumer Product Support
If you require assistance or have questions concerning the application, operation or maintenance of this
product you may call the ECHO Consumer Product Support Department at 1-800-673-1558 from 8:30 am to
4:30 pm (Central Standard Time) Monday through Friday. Before calling, please know the model and serial
number of your unit.
Warranty Registration
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at
product confirms your warranty coverage and provides a direct link between you and ECHO if we find it
necessary to contact you.
Additional or Replacement Manuals
Replacement Operator, Safety Manuals, and Parts Catalogs are available from your ECHO dealer or at
(800-673-1558). Always check the ECHO Web Site for updated information.
Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.
X7531125002
3
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
PB-760 LN H/T
SAFETY
Manual Safety Symbols and Important Information
Throughout this manual and on the product itself, you will find safety alerts and helpful, informational
messages preceded by symbols or key words. The following is an explanation of those symbols and key
words and what they mean to you.
The safety alert symbol accompanied by the word “DANGER” calls attention to an act or condition
which WILL lead to serious personal injury or death if not avoided.
The safety alert symbol accompanied by the word “WARNING” calls attention to an act or condition
which CAN lead to serious personal injury or death if not avoided.
The safety alert symbol accompanied by the word “CAUTION” calls attention to an act or condition
which may lead to minor or moderate personal injury if not avoided.
The enclosed message provides information necessary for the protection of the unit.
Note: This enclosed message provides tips for use, care and maintenance of the unit.
CIRCLE AND SLASH SYMBOL
This symbol means the specific action shown is prohibited. Ignoring these prohibitions can result
in serious or fatal injury.
International Symbols
Symbol
Description
Symbol
Description
Symbol
Description
Symbol
Description
Read and
understand
owners
Carburetor
Adjustment -
Low speed
mixture
Carburetor
Adjustment -
High speed
mixture
Fuel and oil
mixture
manual.
Wear eye, ear
and head
Carburetor
Adjustment -
Idle speed
Finger severing
Hot Surface
Safety/Alert
Idle Speed
protection
Emergency
Stop
Fast speed
Primer Bulb
Wear hand
protection.
Use two
DO NOT smoke
near fuel
Ignition
ON / OFF
handed
Choke Control
“Cold Start”
Position
Choke Control
“Run” Position
(Choke Open)
DO NOT allow
flames or
sparks near fuel
Wear slip
resistant
footwear
(Choke
Closed)
4
X7531125002
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PB-760 LN H/T
SAFETY
Personal Condition and Safety Equipment
Users of this product risk injury to themselves and others if the unit is used improperly and/or safety
precautions are not followed. Proper clothing and safety gear must be worn when operating unit.
Physical Condition
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
• if you are taking medication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection
Eye protection that meets ANSI Z87.1 or CE requirements must be worn whenever you operate the unit.
Hand Protection
Wear no-slip, heavy duty work gloves to improve your grip on the handles. Gloves also reduce the
transmission of machine vibration to your hands.
Breathing Protection
Wear a facemask to protect against dust.
Hearing Protection
ECHO recommends wearing hearing protection whenever unit is used.
Proper Clothing
Wear snug fitting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DO NOT WEAR SHORTS,
• DO NOT WEAR TIES, SCARVES, JEWELRY, or clothing with loose or hanging items that could become
entangled in moving parts or surrounding growth.
Wear sturdy work shoes with nonskid soles;
• DO NOT WEAR OPEN TOED SHOES,
• DO NOT OPERATE UNIT BAREFOOTED.
Wear no-slip, heavy duty work gloves.
Keep long hair away from engine and air intake. Retain hair with cap or net.
Hot Humid Weather
Heavy protective clothing can increase operator fatigue which may lead to heat stroke. Schedule heavy
work for early morning or late afternoon hours when temperatures are cooler.
X7531125002
5
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
PB-760 LN H/T
The ignition components of this machine generate an electromagnetic field during operation which
may interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with
pacemakers should consult with their physician and the pacemaker manufacturer before operating
this machine. In the absence of such information, ECHO does not recommend the use of ECHO
products by anyone who has a pacemaker.
Vibration and Cold
It is believed that a condition called Raynaud’s Phenomenon,
which affects the fingers of certain individuals, may be brought
about by exposure to vibration and cold. Exposure to vibration
and cold may cause tingling and burning sensations, followed
by loss of color and numbness in the fingers. The following
precautions are strongly recommended, because the minimum
exposure, which might trigger the ailment, is unknown.
• Keep your body warm, especially the head, neck, feet, ankles,
hands, and wrists.
• Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and
also by not smoking.
• Limit the hours of operation. Try to fill each day with jobs where operating the unit or other hand-held
power equipment is not required.
• If you experience discomfort, redness, and swelling of the fingers followed by whitening and loss of feeling,
consult your physician before further exposing yourself to cold and vibration.
Repetitive Stress Injuries
It is believed that overusing the muscles and tendons of the
fingers, hands, arms, and shoulders may cause soreness,
swelling, numbness, weakness, and extreme pain in those
areas. Certain repetitive hand activities may put you at a high
risk for developing a Repetitive Stress Injury (RSI). An extreme
RSI condition is Carpal Tunnel Syndrome (CTS), which could
occur when your wrist swells and squeezes a vital nerve that
runs through the area. Some believe that prolonged exposure to
vibration may contribute to CTS. CTS can cause severe pain for
months or even years.
To reduce the risk of RSI/CTS, do the following:
• Avoid using your wrist in a bent, extended, or twisted position. Instead try to maintain a straight wrist
position. Also, when grasping, use your whole hand, not just the thumb and index finger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive movement.
• Do exercise to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if you feel tingling, numbness, or pain in
the fingers, hands, wrists, or arms. The sooner RSI/CTS is diagnosed, the more likely permanent nerve
and muscle damage can be prevented.
6
X7531125002
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PB-760 LN H/T
SAFETY
Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains
poisonous emissions and can cause serious injury or death.
Read the Manual
• Provide all users of this equipment with the Operator’s Manual for
instructions on Safe Operation.
Clear the Work Area
• Spectators and fellow workers must be warned, and children and
animals prevented from coming nearer than 15 m (50 ft.) while the
unit is in use.
• Take wind conditions into account: avoid open doors and windows.
• Do not point blower at people or animals.
• Review area to be cleared. Look for potential hazards such as
stones or metal objects.
Keep a Firm Grip
• Hold the handle in one hand, with thumb and fingers encircling the handle.
Keep a Solid Stance
• Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do not
work in odd positions or on ladders. Do not over reach.
Avoid Hot Surfaces
• Keep exhaust area clear of flammable debris. Avoid contact
during and immediately after operation.
Equipment
Use only ECHO approved attachments. Serious injury may result from the use of a non-approved
attachment combination. ECHO, INC. will not be responsible for the failure of cutting devices,
attachments or accessories which have not been tested and approved by ECHO. Read and comply
with all safety instructions listed in this manual.
• Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed.
• Do not use blower if any part is missing or damaged.
• Have repairs done only by an authorized ECHO Service dealer.
X7531125002
7
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
EMISSION CONTROL (EXHAUST & EVAPORATIVE)
PB-760 LN H/T
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings.
• ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a
complete stop before removing obstructions, clearing debris, or servicing unit.
• DO NOT start or operate unit unless all guards and protective covers are properly assembled to
unit.
• NEVER reach into any opening while the engine is running. Moving parts may not be visible
through openings.
Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage or
leaks are found, do not use unit, otherwise serious personal injury or property damage may occur.
Have unit repaired by an authorized servicing dealer before using.
EMISSION CONTROL (EXHAUST & EVAPORATIVE)
EPA 2010 and Later and/or C.A.R.B. TIER III
The emission control system for the engine is EM (engine modification)
and, if the second to last character of the Engine Family on the Emission
Control Information label (sample below) is “C”, “K”, or “T”, the emission
control system is EM and TWC (3-way catalyst). The fuel tank/fuel line
emission control system is EVAP (evaporative emissions). Evaporative
emissions for California models are only applicable to fuel tanks.
An Emission Control Label is located on the engine. (This is an
EXAMPLE ONLY, information on label varies by engine FAMILY).
Product Emission Durability (Emission Compliance Period)
The 50 or 300 hour emission compliance period is the time span
selected by the manufacturer certifying the engine emissions output
meets applicable emissions regulations, provided that approved
maintenance procedures are followed as listed in the Maintenance Section of this manual.
8
X7531125002
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PB-760 LN H/T
DESCRIPTION
DESCRIPTION
PB-760 LN H
Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow
the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See
PARTS ORDERING instructions for specific information.
8
1
9
11
10
12
2
7
6
5
3
13
15
4
14
Hot Decal
General Warning Decal
Sound Label
X7531125002
9
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION
PB-760 LN H/T
1. SPARK PLUG - Provides spark to ignite fuel mixture.
2. SAFETY DECAL - Lists important safety precautions.
3. SPARK ARRESTOR - CATALYTIC MUFFLER / MUFFLER - The muffler or catalytic muffler controls
exhaust noise and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the
muffler. Keep exhaust area clear of flammable debris.
4. FUEL TANK - Contains fuel and fuel filter.
5. FUEL TANK CAP - Covers and seals fuel tank.
6. RECOIL STARTER HANDLE - Pull recoil handle slowly until recoil starter engages, then quickly and
firmly. When engine starts, return handle slowly. DO NOT let handle snap back or damage to unit will
occur.
7. AIR CLEANER - Contains replaceable air filter element.
8. CHOKE - Move lever UP to close choke (
DOWN to open choke ( ) (run position).
) (starting position) and for emergency stopping. Move
9. PURGE BULB - Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging air from
the carburetor. Pump purge bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump purge
bulb an additional 4 or 5 times.
10. SHOULDER HARNESS - Used to support unit on operator's back. The straps are adjustable.
11. THROTTLE POSITION LEVER/STOP SWITCH - Combination stop switch and variable speed throttle
lever. When the lever is moved all the way forward the blower is at Wide Open Throttle (W.O.T.). When
the lever is moved rearward to detent, the blower is at idle. When the lever is moved rearward past the
idle detent the blower will stop.
12. HANDLE - Rotates downward for throttle control access. Spring loaded for flexible operation.
13. STICK HANDLE - Provides comfortable grip for directing air flow.
14. BLOWER PIPES - Exclusive positive locking system.
15. FLEXIBLE PIPE - Allows for full range of movement
10
X7531125002
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PB-760 LN H/T
DESCRIPTION
PB-760 LN T
Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow
the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See
PARTS ORDERING instructions for specific information.
8
1
9
10
2
7
5
6
12
11
16
3
13
14
4
15
Hot Decal
General Warning Decal
Sound Label
General Warning Decal
X7531125002
11
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION
PB-760 LN H/T
1. SPARK PLUG - Provides spark to ignite fuel mixture.
2. SAFETY DECAL - Lists important safety precautions.
3. SPARK ARRESTOR - CATALYTIC MUFFLER / MUFFLER - The muffler or catalytic muffler controls
exhaust noise and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the
muffler. Keep exhaust area clear of flammable debris.
4. FUEL TANK - Contains fuel and fuel filter.
5. FUEL TANK CAP - Covers and seals fuel tank.
6. RECOIL STARTER HANDLE - Pull recoil handle slowly until recoil starter engages, then quickly and
firmly. When engine starts, return handle slowly. DO NOT let handle snap back or damage to unit will
occur.
7. AIR CLEANER - Contains replaceable air filter element.
8. CHOKE - Move lever UP to close choke (
DOWN to open choke ( ) (run position).
) (starting position) and for emergency stopping. Move
9. PURGE BULB - Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging air from
the carburetor. Pump purge bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump purge
bulb an additional 4 or 5 times.
10. SHOULDER HARNESS - Used to support unit on operator's back. The straps are adjustable.
11. HANDLE - Used by operator to direct and control air flow.
12. COMBINATION THROTTLE POSITION / STOP SWITCH BUTTON - Controls engine speed and turns
ignition on or off. Forward position - STOP. First detent position - IDLE. Move button back to increase
speed, forward to decrease speed. Use Throttle Position Button to set and hold blower speed for
continuous operation.
13. THROTTLE TRIGGER - Spring - loaded Throttle Trigger controls engine speed. Releasing Trigger
returns engine to speed set by Throttle Position Stop Switch Button. Always release trigger and allow
engine to return to idle before shutting off with Throttle Position Stop Switch Button. Use Throttle Trigger
to vary blower speed settings for intermittent operation.
14. LOCKING KNOB - Allows operator to adjust handle position for optimum comfort and control.
15. BLOWER PIPES - Exclusive positive locking system.
16. FLEXIBLE PIPE - Allows for full range of movement.
12
X7531125002
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PB-760 LN H/T
CONTENTS
CONTENTS
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or
missing parts. Use the contents list to check for missing parts.
PB-760 LN H
____ 1 - Power Head
____ 1 - Flex Pipe
____ 1 - Pipe w/swivel
____ 1 - Straight Pipe w/silencer
____ 1 - Straight Pipe
____ 1 - Operator's Manual
____ 1 - Emission Control Warranty Statement
____ 1 - Warranty Registration Card
____ 2 - Clamps w/screws
____ 1 - Stick Handle
____ 1 - Bolt 6x25
____ 1 - Washer 6
____ 1 - Wing nut
____ 1 - Intake cover
____ 1 - Intake cover
PB-760 LN T
____ 1 - Power Head
____ 1 - Flex Pipe
____ 1 - Pipe w/swivel
____ 1 - Straight Pipe w/silencer
____ 1 - Straight Pipe
____ 1 - Operator's Manual
____ 1 - Emission Control Warranty Statement
____ 1 - Warranty Registration Card
____ 2 - Clamps w/screws
____ 1 - Guide Loop
____ 1 - Intake cover
X7531125002
13
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
PB-760 LN H/T
ASSEMBLY
PB-760 LN H
Never perform maintenance or assembly procedures with engine running or serious personal injury
may result.
A
Install Blower Pipes/Stick Handle
1. Assemble clamps (A) onto both ends of flexible pipe (B).
C
B
2. Assemble swivel pipe (C) into flexible pipe (B) and tighten
clamp (A).
3. Assemble flexible pipe (B) to elbow (D) on blower and
tighten clamp (A).
Note: A light lubricant may be used to ease assembly of flexible
pipe to blower elbow.
D
A
B
4. Loosen wing nut (E). Align notches (G) in handle clamp with
tabs (H).
F
5. Slide stick handle onto swivel pipe (C). Stick handle (F)
should be angled away from operator.
C
H
6. Position stick handle (F) for comfortable operation. Tighten
wing nut (E).
E
G
7. Assemble straight pipe w/silencer (J) onto swivel pipe (C),
until you feel light resistance. Do not force connection. Hold
swivel pipe and turn straight pipe clockwise, engaging
positive locking channels, until connection is firm. Do not
force connection.
8. Assemble straight pipe (K) to straight pipe w/silencer (J) as
in step 7.
J
Note:
K
Blower use will eventually loosen pipe connections. Exclusive
positive locking system allows pipes to be tightened. If
loosening occurs, remove two straight pipes and install
according to instructions 7 & 8.
C
14
X7531125002
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PB-760 LN H/T
ASSEMBLY
PB-760 LN T
Never perform maintenance or assembly procedures with engine running or serious personal injury
may result.
Install Blower Pipes
G
G
1. Place guide loop (G) across clamp, and turn until clip fully
engages clamp band.
Note: Clamp with cable guide loop (G) fits elbow end of flexible
pipe (B).
2. Assemble clamps (A) onto both ends of flexible pipe (B).
B
C
A
G
3. Assemble swivel pipe (C) into flexible pipe (B) and tighten
clamp (A).
A
Note: Hang handle freely from blower to assure throttle cable is
not twisted before installing handle (E).
4. Loosen knob (H) on handle (E). Align notch in handle with
tabs (F). Install onto swivel pipe (C) past long ridges in pipe.
E
H
C
F
5. Assemble flexible pipe (B) to elbow (D) on blower. Position
guide loop (G) on outside of flexible pipe (away from blower)
and tighten clamp (A).
A
B
D
G
X7531125002
15
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
PB-760 LN H/T
Note: A light lubricant may be used to ease assembly of flexible
pipe to blower elbow.
G
6. Clip throttle cable into throttle cable guide loop (G).
E
7. Move handle (E) to desired position. Tighten knob (H) hand
tight.
H
8. Assemble straight pipe w/silencer (I) onto swivel pipe (C),
until you feel light resistance. Do not force connection. Hold
swivel pipe and turn straight pipe clockwise, engaging
positive locking channels, until connection is firm. Do not
force connection.
E
9. Assemble straight pipe (J) to straight pipe w/silencer (I) as in
step 8.
I
Note: Blower use will eventually loosen pipe connections.
Exclusive positive locking system allows pipes to be
tightened. If loosening occurs, remove two straight pipes
and install according to instructions 8 &9.
J
C
16
X7531125002
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PB-760 LN H/T
OPERATION
OPERATION
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts
have come to a complete stop before removing obstructions, clearing debris, or servicing unit.
Blower housing may contain shredder blades and other sharp edges that can cause serious injuries
if touched, even if engine is off and blades are not moving. Wear gloves to protect hands from sharp
edges and hot surfaces.
Operation of this equipment may create sparks that can start fires. This unit is equipped with a spark
arrestor to prevent discharge of hot particles from the engine. Metal cutters can also create sparks if
the cutter strikes rocks, metal, or other hard objects. Contact local fire authorities for laws or
regulations regarding fire prevention requirements.
Fuel
Alternative fuels, such as E-15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO
requirements are NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels
may cause performance problems, loss of power, overheating, fuel vapor lock, and unintended
machine operation, including, but not limited to, improper clutch engagement. Alternative fuels may
also cause premature deterioration of fuel lines, gaskets, carburetors and other engine components.
Fuel Requirements
Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may
contain up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing
methanol (wood alcohol) is NOT approved.
Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FD Standards
must be used. Echo brand premium Power Blend X TM Universal 2-Stroke Oil meets these standards. Engine
problems due to inadequate lubrication caused by failure to use an ISO-L-EGD (ISO/CD 13738) and
J.A.S.O. FD certified oil, such as Echo premium Power Blend X TM, will void the two-stroke engine warranty.
Echo premium Power Blend X TM Universal 2-Stroke Oil may be mixed at 50:1 ratio for application in all Echo
engines sold in the past regardless of ratio specified in those manuals.
Handling Fuel
Fuel is VERY flammable. Use extreme care when mixing, storing or handling, or serious personal
injury may result.
• Use an approved fuel container.
• DO NOT smoke near fuel.
• DO NOT allow flames or sparks near fuel.
X7531125002
17
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
PB-760 LN H/T
• Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to
equalize.
• NEVER refuel a unit when the engine is HOT or RUNNING!
• DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground.
• DO NOT overfill fuel tank. Wipe up spills immediately.
• Securely tighten fuel tank cap and close fuel container after refueling.
• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is
repaired.
• Move at least 3m (10 ft.) from refueling location before starting the engine.
Mixing Instructions
1. Fill an approved fuel container with half of the required
amount of gasoline.
2. Add the proper amount of 2-stroke oil to gasoline.
3. Close container and shake to mix oil with gasoline.
4. Add remaining gasoline, close fuel container, and remix.
Spilled fuel is a leading cause of hydrocarbon emissions. Some
states may require the use of automatic fuel shut-off containers
to reduce fuel spillage.
After use
• DO NOT store a unit with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel storage
container.
Storage - Fuel storage laws vary by locality. Contact your local government for the laws affecting your area.
As a precaution, store fuel in an approved, airtight container. Store in a well-ventilated, unoccupied building,
away from sparks and flames.
Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a
fuel stabilizer is added.
Stored two-stroke fuel may separate. ALWAYS shake fuel container thoroughly before each use.
18
X7531125002
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PB-760 LN H/T
OPERATION
Starting Cold Engine
• Recoil starter: Use short pulls - only 1/2-2/3 of rope length for starting. Do not allow the rope to snap back
in. Always hold the unit firmly.
• (PB-760 LN H): Rotate spring loaded throttle arm downward to a comfortable operating position.
- PB-760 LN H
PB-760 LN H
1. Throttle Lever
A
Move throttle position lever (A) to IDLE DETENT positions.
- PB-760 LN T
1. Throttle Position / Stop Switch Button
PB-760 LN T
Slide Throttle Position / Stop Switch Button (A) back to idle
position.
- PB-760 LN H and T
C
2. Choke
Move choke (C) up to Cold Start Position (
)
3. Purge Bulb
E
Pump purge bulb (D) until fuel is visible. Pump bulb an
additional 4 or 5 times.
4. Recoil Starter
D
Pull recoil starter handle (E) until engine fires, or a maximum
of 5 pulls
5. Choke
After engine fires (or 5 pulls), move choke lever back to Run (
) position, then pull starter handle/rope
until engine starts and runs. Allow unit to warm up at idle for several minutes.
Note: If engine does not start with choke in “Run” position after 5 pulls, move choke to “Cold Start” (
position, and repeat steps 4 & 5.
)
6. Throttle Lever
Allow engine to warm up for several minutes before use.
7. Throttle Lever
After engine warm-up, move throttle lever gradually to increase engine RPM to desired operating speed.
X7531125002
19
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
PB-760 LN H/T
Starting Warm Engine
The starting procedure is the same as Cold Start except DO
NOT close the choke.
PB-760 LN H
- PB-760 LN H
A
1. Throttle Lever
Move throttle position lever (A) to IDLE DETENT positions.
- PB-760 LN T
PB-760 LN T
1. Throttle Position / Stop Switch Button
Slide Throttle Position / Stop Switch Button (A) back to idle
position.
- PB-760 LN H and T
C
2. Purge Bulb
Pump purge bulb (D) until fuel is visible. Pump bulb an
additional 4 or 5 times.
E
3. Recoil Starter
Pull recoil starter handle (E) and engine should start. Do not
use choke (C)
D
Note: If engine does not start after 5 pulls, use cold start
procedures.
PB-760 LN H
Stopping Engine
- PB-760 LN H
A
1. Throttle Lever
Move throttle lever (A) to IDLE DETENT position and allow
engine to return to idle before shutting off engine.
2. Throttle Lever
PB-760 LN T
Move throttle lever (A) to "O" (Stop) position.
- PB-760 LN T
1. Throttle Position / Stop Switch Button
Release throttle trigger. Move Throttle Position / Stop Switch Button (A) forward to idle position and allow
engine to return to idle before shutting off engine.
2. Throttle Position / Stop Switch Button
Move Throttle Position / Stop Switch Button (A) all the way forward to STOP position.
If engine does not stop when stop switch is moved to STOP position, close choke - COLD START
position - to stall engine. Have your ECHO dealer repair stop switch before using blower again.
20
X7531125002
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PB-760 LN H/T
OPERATION
Operating Blower
Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause
unconsciousness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position
unit so that exhaust is directed away from your face and body.
Always wear safety glasses, hearing protection and a face filter mask or serious personal injury may
result. Do not point the blower pipe in the direction of people or pets.
Use reduced speed only when performing light-duty tasks or to comply with local noise regulations.
Continuous low speed operation may allow fuel/oil residue to build-up on the piston and cause rapid build-up
of carbon on the spark arrestor screen, resulting in overheating and engine damage. To reduce harmful
build-up, run engine at wide open throttle for at least 5 minutes every hour, and inspect/clean the spark
arrestor screen after approximately 40 hours of operation.
Read the Safety Section carefully.
To avoid engine damage due to over-revving, do not block blower pipe.
1. Use only during appropriate hours.
2. Allow the engine to warm up at a fast idle for a few minutes.
3. PB-760 LN H
PB-760 LN H
Set engine speed with throttle lever (A).
A
PB-760 LN T
Control engine speed with throttle trigger (C), or for
continuous use, set engine speed with Combination Throttle
Position / Stop Switch Button (A).
PB-760 LN T
C
4. Use lower speed to blow dry leaves from walks, patios and
drives.
5. Additional speed may be necessary to clean grass and leaves from a lawn or flower bed.
6. Higher speed may be necessary to move gravel, dirt, snow, bottles or cans from a driveway, street,
parking lot or stadium.
7. Always stop unit using stop engine procedure.
Note: Never use a higher speed setting than necessary to perform a task. Remember, the higher the engine
speed, the louder the blower noise. Minimize dust by using blower at lower speeds. Keep debris on
your property. Be Smart - be a good neighbor.
X7531125002
21
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
PB-760 LN H/T
Cold Weather Operation:
1. Remove back cushion (A) from frame.
2. Install intake cover (B) on frame over air intake.
A
3. Install back cushion (A) to frame over intake cover.
Note: Blower performance may be reduced slightly.
B
22
X7531125002
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PB-760 LN H/T
MAINTENANCE
MAINTENANCE
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts
have come to a complete stop before removing obstructions, clearing debris, or servicing unit.
Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and
hot surfaces.
Your ECHO unit is designed to provide many hours of trouble free service. Regular scheduled maintenance
will help your unit achieve that goal. If you are unsure or are not equipped with the necessary tools, you may
want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to
DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is
not listed, see your ECHO Dealer for repairs.
Skill Levels
Level 1 = Easy to do. Common tools may be required.
Level 2 = Moderate difficulty. Some specialized tools may be required.
ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier.
Maintenance Intervals
DAILY
REQ’D
MAINTENANCE
PROCEDURE
OR
EVERY
3
COMPONENT/SYSTEM
SKILL
YEARLY
BEFORE REFUEL MONTHS
USE
LEVEL
Air Filter
Inspect/Clean
1
1
1
1
1
1
2
2
2
1
1
I / C *
I / C
R *
Choke Shutter
Fuel Filter
Inspect/Clean
Inspect/Replace
I *
I *
I / R *
R *
Fuel Cap Gasket
Fuel System
Inspect/Replace
Inspect/Replace
I (1) *
I / C
I (1) *
Spark Plug
Inspect/Clean/Replace
Inspect/Clean
I / C / R *
Cooling System
Muffler Spark Arrestor
Cylinder Exhaust Port
Recoil Starter Rope
Screws/Nuts/Bolts
Inspect/Clean/Replace
Inspect/Clean/Decarbon
Inspect/Clean
I / C / R *
I / C
I / C *
I *
Inspect/Tighten/Replace
MAINTENANCE PROCEDURE LETTER CODES: I = INSPECT, R = REPLACE, C = CLEAN
IMPORTANT NOTE - Time intervals shown are maximum. Actual use and your experience will determine
the frequency of required maintenance.
MAINTENANCE PROCEDURE NOTES:
(1) Low evaporative fuel tanks DO NOT require regular maintenance to maintain emission integrity.
* Replacement is recommended based on the finding of damage or wear during inspection.
X7531125002
23
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
PB-760 LN H/T
Air Filter
Level 1.
REPOWERTM TUNE UP KIT.
Parts Required:
1. Close choke (cold start position). This prevents dirt from
entering the carburetor throat when the air filter is removed.
Brush accumulated dirt from air cleaner area.
A
2. Remove air filter cover, air filter, retainer, and foam pre-filter.
Brush dirt from inside cover.
B
Foam Pre-Filter (A):
• Clean foam filter in water/detergent solution and rinse with clean water.
• Wrap the filter in a clean, dry cloth and squeeze (do not wring) dry. Allow to dry completely before reuse.
Do not oil.
Air Filter (B):
• Lightly brush debris from filter.
• Replace filter if it is damaged, very dirty, or the rubber sealing edges are deformed.
• If filter can be reused, be certain it fits tightly in the air filter cavity, and is installed with the original side out.
3. Assemble components in reverse order.
Fuel Filter
Level 1.
REPOWERTM TUNE UP KIT.
Parts Required:
Fuel is VERY flammable. Use extreme care when mixing,
storing or handling, or serious personal injury may result.
1. Use a clean rag to remove loose dirt from around fuel cap
and empty fuel tank.
2. Use the “fuel line hook” to pull the fuel line and filter from the tank.
3. Remove the filter from the line and install the new filter.
Note: Federal EPA regulations require all model year 2012 and later gasoline powered engines produced for
sale in the United States to be equipped with a special low permeation fuel supply hose between the
carburetor and fuel tank. When servicing model year 2012 and later equipment, only fuel supply
hoses certified by EPA can be used to replace the original equipment supply hose. Fines up to
$37,500 may be enforced for using an un-certified replacement part.
24
X7531125002
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PB-760 LN H/T
MAINTENANCE
Spark Plug
Level 2.
REPOWERTM Tune-Up Kit
Parts Required:
Use only NGK BPM-6Y spark plug (BPMR-6Y in Canada)
otherwise severe engine damage may occur.
0.65 mm
(0.026 in.)
1. Remove spark plug and check for fouling, worn and rounded
center electrode.
2. Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage
engine.
3. Adjust spark plug gap by bending outer electrode.
4. Tighten spark plug to 150-170 kgf • cm (130-150 in • lbf).
Cooling System
Level 2.
Parts Required: None if you are careful.
To maintain proper engine operating temperatures, cooling air must pass freely through the cylinder fin area.
This flow of air carries combustion heat away from the engine.
Overheating and engine seizure can occur when:
• Air intakes are blocked, preventing cooling air from
reaching the cylinder.
• Dust and grass build up on the outside of the cylinder. This
build up insulates the engine and prevents the heat from
leaving.
Removal of cooling passage blockages or cleaning of cooling
fins is considered “Normal Maintenance.” Any failure
attributed to lack of maintenance is not warranted.
Cleaning Grill
1. Brush accumulated debris from intake grill between backpack frame and blower housing.
X7531125002
25
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
PB-760 LN H/T
Cleaning Cylinder Fins
1. Disconnect spark plug lead from spark plug.
2. Remove air filter cover.
B
A
3. Remove muffler cover (A)
4. Remove engine cover (B)
5. Clean cylinder fins (C) to allow cooling air to pass freely
6. Install engine cover and muffler cover.
7. Install air filter cover.
8. Connect spark plug lead.
C
Exhaust System
Spark Arrestor Screen
Level 2.
Parts Required: Spark Arrestor Screen, Gasket
Carbon deposits in muffler will cause a drop in engine output
and overheating. Spark arrestor screen must be checked
periodically.
1. Disconnect spark plug lead from spark plug
2. Remove muffler cover (A).
3. Remove spark arrestor cover (B), gasket (C) and spark
arrestor screen (D) from muffler. Replace screen if plugged
with carbon deposits.
A
Note: When cleaning carbon deposits, be careful not to damage
the catalytic element inside muffler.
4. Install spark arrestor screen, gasket, and spark arrestor
cover.
5. Install muffler cover.
6. Connect spark plug lead.
D
C
B
26
X7531125002
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PB-760 LN H/T
MAINTENANCE
Exhaust Port Cleaning
Level 2.
B
Parts Required: As needed: Muffler Gasket
C
1. Remove spark plug lead from spark plug.
2. Remove muffler cover and engine cover.
3. Place piston at top dead center. Remove muffler (A) muffler
gasket (B), and muffler insulator (C).
A
4. Use a wood or plastic scraping tool to clean deposits from
cylinder exhaust port.
Never use a metal tool to scrape carbon from the exhaust port. Do not scratch the cylinder or piston when
cleaning the exhaust port. Do not allow carbon particles to enter the cylinder.
5. Inspect muffler gasket, and replace if damaged.
6. Install muffler insulator, muffler gasket and muffler.
7. Tighten muffler mounting bolts (or nuts) to 95-130 in•lbf
(110-150 kgf•cm).
8. Install engine cover and attach spark plug lead
9. Start engine, and warm to operating temperature.
10. Stop engine, and re-tighten mounting bolts (or nuts) to
specifications.
11. Install muffler cover.
Carburetor Adjustment
Engine Break-In
New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor
adjustments can be made. During the break-in period your engine performance will increase and exhaust
emissions will stabilize. Idle speed can be adjusted as required.
High Altitude Operation
This engine has been factory adjusted to maintain satisfactory starting, emission, and durability performance
up to 1,100 feet above sea level (ASL) (96.0 kPa). To maintain proper engine operation and emission
compliance above 1,100 feet ASL the carburetor may need to be adjusted by an authorized ECHO service
dealer.
If the engine is adjusted for operation above 1,100 feet ASL, the carburetor must be re-adjusted when
operating the engine below 1,100 feet ASL, otherwise severe engine damage may result.
Level 2.
Parts Required: None
X7531125002
27
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
PB-760 LN H/T
Note: Every unit is run at the factory and the carburetor is set in compliance with emission regulations.
Carburetor adjustments, other than idle speed, must be performed by an authorized ECHO dealer.
Idle Adjustment
Before adjustment make sure that:
• Air filter is clean and properly installed.
• Spark arrestor screen and muffler are free of carbon.
• Blower pipes are installed.
1. Start engine, run at idle for one minute.
2. Complete warm up by running at full throttle for 5 minutes,
operating choke twice to clear air from carburetor chambers.
A
3. Check idle speed and reset if necessary. If a tachometer is
available, idle speed screw (A) should be set to the
specifications found on "Specifications" Page of this
manual. Turn idle screw (A) clockwise to increase idle
speed; counter clockwise to decrease idle speed.
28
X7531125002
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PB-760 LN H/T
TROUBLESHOOTING
TROUBLESHOOTING
ENGINE PROBLEM TROUBLESHOOTING CHART
Problem
Check
Status
Cause
Remedy
Fuel strainer clogged
Fuel line clogged
Carburetor
Clean or replace
Clean or replace
See your Echo dealer
Fuel at carburetor No fuel at carburetor
No fuel at cylinder
Carburetor
See your Echo dealer
Open choke
Fuel at cylinder
Clean/replace air filter
Adjust carburetor
See your Echo dealer
Muffler wet with fuel
Fuel Mixture too rich
Enginecranks-
starts hard/
doesn’t start
Stop switch off
Electrical problem
Interlock switch
Turn switch to ON
See your Echo dealer
See your Echo dealer
Spark at end of
No spark
plug wire
Spark gap incorrect
Covered with carbon
Fouled with fuel
Adjust to .65mm (0.026 in.)
Clean or replace
Clean or replace
Spark at plug
No spark
Plug defective
Replace plug
Air filter
Air filter dirty
Normal wear
Clean or replace
Contaminants/residues
in fuel
Fuel filter
Fuel filter dirty
Replace
Contaminants/residues
in fuel
Engine runs,
but dies or
does not
accelerate
properly
Fuel vent
Fuel vent plugged
Clean or replace
Spark Plug
Carburetor
Plug dirty/worn
Normal wear
Vibration
Clean and adjust or replace
Adjust
Improper adjustment
Cooling system
dirty/plugged
Extended operation in
dirty/dusty locations
Cooling System
Clean
Spark Arrestor
Screen
Spark arrestor screen
plugged
Normal wear
Replace
Engine does
not crank
N/A
N/A
Internal engine problem See your Echo dealer
Engine runs,
blower doesn't
work or is
Blower pipe
Pipe clogged
Pipe loose
Build-up of debris
Vibration
Unclog
Tighten
Replace
Pipe damaged
Wear/Misuse
weak/uneven
Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition
spark by grounding spark plug near cylinder plug hole, otherwise serious personal injury may
result.
X7531125002
29
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
PB-760 LN H/T
STORAGE
During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep
exhaust area clear of flammable debris during transportation or when storing, otherwise serious
property damage or personal injury may result.
Long Term Storage (Over 30 Days)
Do not store your unit for a prolonged period of time (30 days or longer) without performing protective
storage maintenance which includes the following:
1. Store unit in a dry, dust free place, out of the reach of children.
Do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark.
2. Place the stop switch in the “OFF” position.
3. Remove accumulation of grease, oil, dirt and debris from exterior of unit.
4. Perform all periodic lubrication and services that are required.
5. Tighten all the screws and nuts.
6. Drain fuel tank completely. Press purge bulb 6 -7 times to remove remaining fuel from carburetor then
drain the tank again. Close choke, start and run the engine until it stops due to lack of fuel.
7.
a. Allow engine to cool then remove the spark plug and pour 7 cc (1/4 oz.) of fresh, clean, two-stroke
engine oil into the cylinder through the spark plug hole.
b. Pull the recoil starter handle 2-3 times to distribute the oil inside the engine.
c. Observe the piston location through the spark plug hole. Pull the recoil handle slowly until the piston
reaches the top of its travel and leave it there.
8. Install the spark plug (do not connect ignition cable).
9. Remove blower pipe assembly from unit.
30
X7531125002
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PB-760 LN H/T
SPECIFICATIONS
SPECIFICATIONS
MODEL
Length 760 LN H
Length 760 LN T
Width 760 LN H
Width 760 LN T
Height 760 LN H
Height 760 LN T
Weight (dry) 760 LN H
Weight (dry) 760 LN T
Engine Type
PB-760 LN H, PB-760 LN T
375mm (14.8 in.) (w/o pipes)
375mm (14.8 in.) (w/o pipes)
535 mm (21.1 in.)
490 mm (19.3 in.)
475 mm (18.7 in.)
475 mm (18.7 in.)
10.9 kg (24 lb.) (w/o pipes)
10.8 kg (23.8 lb.) (w/o pipes)
Air cooled, two-stroke, single cylinder gasoline engine
48.0 mm (1.89 in.)
Bore
Stroke
35.0 mm (1.38 in.)
Displacement
Exhaust
63.3cc (3.86 cu. in.)
Spark arrestor - catalytic muffler / muffler
Diaphragm model w/purge bulb
Flywheel magneto, capacitor discharge ignition type
NGK BPM-6Y (Gap 0.65 mm (0.026 in.)
Mixed (Gasoline and Two-stroke Oil)
Carburetor
Ignition System
Spark Plug
Fuel
50 : 1 Power Blend XTM ISO-L-EGD (ISO/CD 13738) and J.A.S.O. M345- FD, two-stroke,
air-cooled engine oil.
Fuel/Oil Ratio
Gasoline
Use 89 Octane unleaded. Do not use fuel containing methyl alcohol, more than 10% ethyl
alcohol or 15% MTBE. Do not use alternative fuels such as E-15 or E-85.
Oil
Power Blend XTM Premium Universal 2-Stroke Oil
Fuel Tank Capacity
Starter System
Idle Speed
2.02 lit. (68.3 US fl. oz.)
Automatic Rrecoil Starter, centrifugal type
2,450 RPM
Wide Open Throttle Speed (W.O.T.) 6,000 RPM
Maximum Air Speed w/pipes
Average Air Speed w/pipes
Air Volume
95.7 m/sec (214 mph)
79.6 m/sec (178 mph)
15.1 m3/min. (535 cu. ft./min.)
Sound Level at 50 ft. dB(A) scale per 65 dB(A)
ANSI B175.265 dB(A)
X7531125002
31
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY STATEMENTS
PB-760 LN H/T
WARRANTY STATEMENTS
ECHO LIMITED WARRANTY STATEMENT FOR
PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010
ECHO'S RESPONSIBILITY
ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship.
Under normal use and maintenance from date of purchase, ECHO agrees to repair or replace at ECHO’s discretion, any defective product
free of charge at any authorized ECHO servicing dealer within listed below application time periods, limitations and exclusions. THIS LIMITED
WARRANTY IS ONLYAPPLICABLE TO ECHO PRODUCTS SOLD BYAUTHORIZED ECHO DEALERS. IT IS EXTENDED TO THE ORIGINAL
PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair
parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period. Any
damage caused by improper installation or improper maintenance is not covered by this warranty. All parts or products replaced under warranty
become the property of ECHO, Inc. This warranty is separate from the Emission control warranty statement supplied with your new product.
Please consult the Emission Control Warranty Statement for details regarding emission related parts. For a list of Authorized ECHO Dealers
refer to WWW.ECHO-USA.COM or call 1-800-432-ECHO.
OWNER’S RESPONSIBILITY
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at WWW.ECHO-USA.COMꢀꢁꢂꢀꢃꢄꢀꢅꢆꢆ-
ꢇꢈꢉꢀꢁꢊꢋꢀꢋꢌꢍꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢂꢍꢉꢇꢐꢋꢂꢏꢋꢇꢁꢈꢀꢑꢏꢂꢒꢀꢐꢊꢓꢓꢆꢇꢍꢒꢀꢎꢇꢋꢌꢀꢄꢁꢊꢂꢀꢊꢈꢇꢋꢔꢀꢕꢍꢉꢇꢐꢋꢍꢂꢇꢈꢉꢀꢄꢁꢊꢂꢀꢓꢂꢁꢒꢊꢑꢋꢀꢑꢁꢈꢅꢂꢖꢐꢀꢄꢁꢊꢂꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢑꢁꢗꢍꢂꢏꢉꢍꢀꢏꢈꢒꢀꢓꢂꢁꢗꢇꢒꢍꢐꢀꢏꢀꢒꢇꢂꢍꢑꢋꢀ
ꢆꢇꢈꢘꢀꢇꢙꢀꢎꢍꢀꢅꢈꢒꢀꢇꢋꢀꢈꢍꢑꢍꢐꢐꢏꢂꢄꢀꢋꢁꢀꢑꢁꢈꢋꢏꢑꢋꢀꢄꢁꢊꢔ
The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in the
ꢁꢓꢍꢂꢏꢋꢁꢂꢝꢐꢀꢖꢏꢈꢊꢏꢆꢔꢀꢚꢌꢁꢊꢆꢒꢀꢏꢀꢓꢂꢁꢒꢊꢑꢋꢀꢒꢇꢙꢅꢑꢊꢆꢋꢄꢀꢁꢑꢑꢊꢂꢛꢀꢄꢁꢊꢀꢖꢊꢐꢋꢛꢀꢏꢋꢀꢄꢁꢊꢂꢀꢍꢜꢓꢍꢈꢐꢍꢛꢀꢒꢍꢆꢇꢗꢍꢂꢀꢁꢂꢀꢐꢌꢇꢓꢀꢄꢁꢊꢂꢀ!"#$ꢀꢊꢈꢇꢋꢀꢋꢁꢀꢏꢈꢀꢏꢊꢋꢌꢁꢂꢇ%ꢍꢒꢀ!"#$ꢀꢐꢍꢂꢗꢇꢑꢇꢈꢉꢀ
dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit after the repairs have been
made. For your nearest authorized ECHO servicing dealer, call ECHO’s Dealer Referral Center, at 1-800-432-ECHO or you can locate an ECHO
servicing dealer at WWW.ECHO-USA.COM. Should you require assistance or have questions concerning ECHO’s Warranty Statement, you
can contact our Consumer Product Support Department at 1-800-673-1558 or contact us through the web at WWW.ECHO-USA.COM.
PRODUCT WARRANTY PERIOD
RESIDENTIAL APPLICATION
#ꢀꢀ 5 YEAR WARRANTY - All units for residential, or non-income producing use will be covered by this limited warranty for [ꢀꢁ ꢂꢃꢄꢅꢆꢁꢇꢈꢉ from
date of purchase.
EXCEPTIONS:
#ꢀ 'ꢁꢂꢀꢋꢎꢁ*ꢐꢋꢂꢁꢘꢍꢀꢍꢈꢉꢇꢈꢍꢀꢓꢁꢎꢍꢂꢍꢒꢀꢓꢂꢁꢒꢊꢑꢋꢐꢛꢀꢋꢌꢍꢀꢍꢆꢍꢑꢋꢂꢁꢈꢇꢑꢀꢇꢉꢈꢇꢋꢇꢁꢈꢀꢖꢁꢒꢊꢆꢍꢛꢀ\ꢍꢜꢇꢃꢆꢍꢀꢒꢂꢇꢗꢍꢀꢑꢏꢃꢆꢍꢐꢛꢀꢚꢕ/ꢀꢐꢁꢆꢇꢒꢀꢒꢂꢇꢗꢍꢀꢐꢌꢏꢙꢋꢐꢛꢀꢏꢈꢒꢀ9"ꢀꢋꢇꢈꢍꢐꢀ
are warranted for the ꢊꢋꢌꢁꢍ of the product on parts only.
#ꢀ "ꢊꢋꢋꢇꢈꢉꢀꢏꢋꢋꢏꢑꢌꢖꢍꢈꢋꢐꢀꢐꢊꢑꢌꢀꢏꢐꢛꢀꢃꢊꢋꢀꢈꢁꢋꢀꢆꢇꢖꢇꢋꢍꢒꢀꢋꢁꢛꢀꢃꢏꢂꢐꢛꢀꢑꢌꢏꢇꢈꢐꢛꢀꢐꢓꢂꢁꢑꢘꢍꢋꢐꢛꢀꢃꢆꢏꢒꢍꢐꢛꢀꢏꢈꢒꢀꢈꢄꢆꢁꢈꢀꢋꢂꢇꢖꢖꢍꢂꢀꢌꢍꢏꢒꢐꢀꢙꢁꢂꢀꢂꢍꢐꢇꢒꢍꢈꢋꢇꢏꢆꢀꢁꢂꢀꢈꢁꢈ*ꢇꢈꢑꢁꢖꢍꢀ
producing use will be covered for failures due to defects in material or workmanship for a period of ꢎꢏꢅꢐꢇꢆꢉ from original product
purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty.
#ꢀꢀ !"#$ꢝꢐꢀꢕꢏꢓꢇꢒꢀ:ꢁꢏꢒꢍꢂꢀꢚꢋꢂꢇꢈꢉꢀ#ꢍꢏꢒꢀꢑꢏꢂꢂꢇꢍꢐꢀꢏꢀꢆꢇꢙꢍꢋꢇꢖꢍꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢁꢈꢀꢋꢌꢍꢀꢆꢇꢈꢍꢀꢆꢁꢑꢘꢇꢈꢉꢀꢐꢄꢐꢋꢍꢖꢛꢀꢓꢏꢂꢋꢐꢀꢁꢈꢆꢄ;ꢀꢈꢁꢀꢆꢏꢃꢁꢂꢔꢀꢕꢍꢙꢍꢂꢀꢋꢁꢀꢄꢁꢊꢂꢀꢁꢓꢍꢂꢏꢋꢁꢂꢝꢐꢀ
manual for string head installation and maintenance instructions.
#ꢀꢀ <ꢆꢆꢀꢚ=*ꢚꢍꢂꢇꢍꢐꢀꢏꢈꢒꢀ>ꢕ$ꢀ<99<"#/!?9ꢀꢚ!ꢕ@!ꢚꢀꢚꢓꢆꢇꢋꢀꢚꢌꢏꢙꢋꢀꢏꢋꢋꢏꢑꢌꢖꢍꢈꢋꢐꢀꢑꢏꢂꢂꢄꢀꢋꢌꢍꢀꢐꢏꢖꢍꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢒꢊꢂꢏꢋꢇꢁꢈꢀꢏꢐꢀꢋꢌꢍꢀꢊꢈꢇꢋꢐꢀꢋꢌꢍꢄꢀꢏꢂꢍꢀ
ꢒꢍꢐꢇꢉꢈꢍꢒꢀꢋꢁꢀꢅꢋꢔ
COMMERCIAL APPLICATION
#ꢀꢀ 1 YEAR WARRANTY - All Chain Saws, QuikVent Saws, and Cut-Off Saws for commercial, institutional, agricultural, industrial, or income
producing use will be covered by this limited warranty for one ꢂꢑꢄꢅꢆꢁꢇꢈ from the date of purchase.
#ꢀꢀ 2 YEAR WARRANTY - All other units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this
limited warranty for two ꢂꢒꢄꢅꢆꢁꢇꢈꢉ from the date of purchase.
EXCEPTIONS:
#ꢀ 'ꢁꢂꢀꢋꢎꢁ*ꢐꢋꢂꢁꢘꢍꢀꢍꢈꢉꢇꢈꢍꢀꢓꢁꢎꢍꢂꢍꢒꢀꢓꢂꢁꢒꢊꢑꢋꢐꢛꢀꢋꢌꢍꢀꢍꢆꢍꢑꢋꢂꢁꢈꢇꢑꢀꢇꢉꢈꢇꢋꢇꢁꢈꢀꢖꢁꢒꢊꢆꢍꢛꢀ\ꢍꢜꢇꢃꢆꢍꢀꢒꢂꢇꢗꢍꢀꢑꢏꢃꢆꢍꢐꢛꢀꢚꢕ/ꢀꢐꢁꢆꢇꢒꢀꢒꢂꢇꢗꢍꢀꢐꢌꢏꢙꢋꢐꢀꢏꢈꢒꢀ9"ꢀꢋꢇꢈꢍꢐꢛꢀ
are warranted for the ꢊꢋꢌꢁꢍ of the product on parts only.
#ꢀ "ꢊꢋꢋꢇꢈꢉꢀꢏꢋꢋꢏꢑꢌꢖꢍꢈꢋꢐꢀꢐꢊꢑꢌꢀꢏꢐꢛꢀꢃꢊꢋꢀꢈꢁꢋꢀꢆꢇꢖꢇꢋꢍꢒꢀꢋꢁꢛꢀꢃꢏꢂꢐꢛꢀꢑꢌꢏꢇꢈꢐꢛꢀꢐꢓꢂꢁꢑꢘꢍꢋꢐꢛꢀꢃꢆꢏꢒꢍꢐꢛꢀꢏꢈꢒꢀꢈꢄꢆꢁꢈꢀꢋꢂꢇꢖꢖꢍꢂꢀꢌꢍꢏꢒꢐꢀꢙꢁꢂꢀꢑꢁꢖꢖꢍꢂꢑꢇꢏꢆꢛꢀꢇꢈꢐꢋꢇꢋꢊꢋꢇꢁꢈꢏꢆꢛꢀ
agricultural, industrial, rental, or income producing will be covered for failures due to defects in material or workmanship for a period
of ꢓꢏꢅꢐꢇꢆꢉ from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by
this warranty.
#ꢀꢀ !"#$ꢝꢐꢀꢕꢏꢓꢇꢒꢀ:ꢁꢏꢒꢍꢂꢀꢚꢋꢂꢇꢈꢉꢀ#ꢍꢏꢒꢀꢑꢏꢂꢂꢇꢍꢐꢀꢏꢀꢆꢇꢙꢍꢋꢇꢖꢍꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢁꢈꢀꢋꢌꢍꢀꢆꢇꢈꢍꢀꢆꢁꢑꢘꢇꢈꢉꢀꢐꢄꢐꢋꢍꢖꢛꢀꢓꢏꢂꢋꢐꢀꢁꢈꢆꢄ;ꢀꢈꢁꢀꢆꢏꢃꢁꢂꢔꢀꢕꢍꢙꢍꢂꢀꢋꢁꢀꢄꢁꢊꢂꢀꢁꢓꢍꢂꢏꢋꢁꢂꢝꢐꢀ
manual for string head installation and maintenance instructions.
#ꢀꢀ <ꢆꢆꢀꢚ=*ꢚꢍꢂꢇꢍꢐꢀꢏꢈꢒꢀ>ꢕ$ꢀ<99<"#/!?9ꢀꢚ!ꢕ@!ꢚꢀꢚꢓꢆꢇꢋꢀꢚꢌꢏꢙꢋꢀꢏꢋꢋꢏꢑꢌꢖꢍꢈꢋꢐꢀꢑꢏꢂꢂꢄꢀꢋꢌꢍꢀꢐꢏꢖꢍꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢒꢊꢂꢏꢋꢇꢁꢈꢀꢏꢐꢀꢋꢌꢍꢀꢊꢈꢇꢋꢐꢀꢋꢌꢍꢄꢀꢏꢂꢍꢀ
ꢒꢍꢐꢇꢉꢈꢍꢒꢀꢋꢁꢀꢅꢋꢔ
RENTAL APPLICATION - 90 DAYS WARRANTY
#ꢀꢀBꢈꢇꢋꢐꢀꢙꢁꢂꢀꢂꢍꢈꢋꢏꢆꢀꢊꢐꢍꢀꢎꢇꢆꢆꢀꢃꢍꢀꢑꢁꢗꢍꢂꢍꢒꢀꢏꢉꢏꢇꢈꢐꢋꢀꢒꢍꢙꢍꢑꢋꢐꢀꢇꢈꢀꢖꢏꢋꢍꢂꢇꢏꢆꢀꢏꢈꢒꢀꢎꢁꢂꢘꢖꢏꢈꢐꢌꢇꢓꢀꢙꢁꢂꢀꢏꢀꢓꢍꢂꢇꢁꢒꢀꢁꢙꢀGJꢀꢒꢏꢄꢐꢀꢙꢂꢁꢖꢀꢋꢌꢍꢀꢒꢏꢋꢍꢀꢁꢙꢀꢓꢊꢂꢑꢌꢏꢐꢍꢔꢀ
ꢍꢀꢀ !"#$ꢝꢐꢀꢆꢇꢏꢃꢇꢆꢇꢋꢄꢀꢊꢈꢒꢍꢂꢀꢋꢌꢍꢀO:ꢇꢙꢍꢋꢇꢖꢍPꢀꢑꢁꢗꢍꢂꢏꢉꢍꢀꢇꢐꢀꢆꢇꢖꢇꢋꢍꢒꢀꢋꢁꢀꢙꢊꢂꢈꢇꢐꢌꢇꢈꢉꢀꢓꢏꢂꢋꢐꢀꢐꢓꢍꢑꢇꢅꢍꢒꢀꢊꢈꢒꢍꢂꢀꢋꢌꢍꢀ>ꢕ$XB"9ꢀY<ꢕꢕ<?9Zꢀ>!ꢕ@$X section of
this warranty statement for OꢔꢋꢌꢁPꢀꢙꢂꢍꢍꢀꢁꢙꢀꢑꢌꢏꢂꢉꢍꢀꢙꢁꢂꢀꢏꢀꢓꢍꢂꢇꢁꢒꢀꢁꢙꢀꢋꢍꢈꢀ[\J]ꢀꢄꢍꢏꢂꢐꢀꢏꢙꢋꢍꢂꢀꢋꢌꢍꢀꢒꢏꢋꢍꢀꢁꢙꢀꢋꢌꢍꢀꢑꢁꢖꢓꢆꢍꢋꢍꢀꢊꢈꢇꢋꢝꢐꢀꢅꢈꢏꢆꢀꢓꢂꢁꢒꢊꢑꢋꢇꢁꢈꢔꢀ
32
X7531125002
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PB-760 LN H/T
WARRANTY STATEMENTS
PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES
#ꢀꢀGJ*ꢒꢏꢄꢀꢂꢍꢐꢇꢒꢍꢈꢋꢇꢏꢆꢛꢀꢁꢂꢀꢈꢁꢈ*ꢇꢈꢑꢁꢖꢍꢀꢓꢂꢁꢒꢊꢑꢇꢈꢉꢀꢎꢏꢂꢂꢏꢈꢋꢄ
#ꢀꢀ^J*ꢒꢏꢄꢀꢑꢁꢖꢖꢍꢂꢑꢇꢏꢆꢛꢀꢇꢈꢐꢋꢇꢋꢊꢋꢇꢁꢈꢏꢆꢛꢀꢏꢉꢂꢇꢑꢊꢆꢋꢊꢂꢏꢆꢛꢀꢇꢈꢒꢊꢐꢋꢂꢇꢏꢆꢛꢀꢇꢈꢑꢁꢖꢍꢀꢓꢂꢁꢒꢊꢑꢇꢈꢉꢛꢀꢁꢂꢀꢂꢍꢈꢋꢏꢆꢀꢏꢓꢓꢆꢇꢑꢏꢋꢇꢁꢈꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢀ
ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS
This ECHO two-stroke engine power product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior
performance. To help ensure the performance of the unit, it is required to use two-stroke oil which meets the ISO-L-EGD Standard per ISO/CD
13738 and JASO M345FD Standards. ꢕꢖꢗꢘꢅꢙꢚ!ꢁꢈꢅ"ꢊꢁ#ꢐ(ꢅ%!ꢚ&()ꢈꢚ*ꢁꢅꢘꢋꢊ ꢇꢐꢀꢏꢀꢓꢂꢍꢖꢇꢊꢖꢀꢋꢎꢁ*ꢐꢋꢂꢁꢘꢍꢀꢁꢇꢆꢀꢐꢓꢍꢑꢇꢅꢑꢏꢆꢆꢄꢀꢙꢁꢂꢖꢊꢆꢏꢋꢍꢒꢀꢋꢁꢀꢖꢍꢍꢋꢀ@ꢚ$*
L-EGD (ISO/CD 13738) and JASO M345FD Standards. The use of two-stroke oils designed for other applications, such as for outboard motors
or lawnmowers can result in severe engine damage, and will void your two-stroke engine limited warranty.
THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY:
#ꢀ
:ꢏꢑꢘꢀꢁꢙꢀꢆꢊꢃꢂꢇꢑꢏꢋꢇꢁꢈꢀꢁꢂꢀꢍꢈꢉꢇꢈꢍꢀꢙꢏꢇꢆꢊꢂꢍꢛꢀꢒꢊꢍꢀꢋꢁꢀꢋꢌꢍꢀꢊꢐꢍꢀꢁꢙꢀꢋꢎꢁ*ꢐꢋꢂꢁꢘꢍꢀꢁꢇꢆꢐꢀthat do not meet the ISO-L-EGD (ISO/CD 13738) and JASO M345FD
Standards. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD compliant and JASO M345FD registered
oil, will void the two-stroke engine limited warranty. !"#$ꢀ>ꢁꢎꢍꢂꢀ=ꢆꢍꢈꢒ(ꢀ9ꢎꢁ*ꢚꢋꢂꢁꢘꢍꢀ$ꢇꢆ meets the ISO-L-EGD and JASO M345FD
Standard. Emission related parts are covered for 5 years residential use or 2 years commercial use regardless of two-stroke oil used, per
the statement listed in the EPA or California Emission Defect Warranty Explanation.
Xꢏꢖꢏꢉꢍꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢊꢐꢍꢀꢁꢙꢀꢉꢏꢐꢁꢌꢁꢆꢛꢀꢑꢁꢈꢋꢏꢇꢈꢇꢈꢉꢀꢖꢍꢋꢌꢏꢈꢁꢆꢀ[ꢎꢁꢁꢒꢀꢏꢆꢑꢁꢌꢁꢆ]ꢛꢀꢁꢂꢀꢉꢏꢐꢁꢆꢇꢈꢍꢀꢑꢁꢈꢋꢏꢇꢈꢇꢈꢉꢀꢆꢍꢐꢐꢀꢋꢌꢏꢈꢀ|Gꢀꢁꢑꢋꢏꢈꢍ. Only use gasoline which
contains |Gꢀꢁꢑꢋꢏꢈꢍꢀꢁꢂꢀꢌꢇꢉꢌꢍꢂ. Gasohol which contains a +ꢇ6ꢋ+7+ꢀ\J}ꢀꢍꢋꢌꢏꢈꢁꢆꢀ[ꢉꢂꢏꢇꢈꢀꢏꢆꢑꢁꢌꢁꢆ]ꢀꢁꢂꢀ\~}ꢀ/9=!ꢀ[ꢖꢍꢋꢌꢄꢆꢋꢍꢂꢋꢇꢏꢂꢄꢃꢊꢋꢄꢆꢍꢋꢌꢍꢂ]ꢀ
is also approved. The prescribed mixing ratio of gasoline to oil is listed on the ECHO oil label and covered in your operator’s manual.
!ꢈꢉꢇꢈꢍꢀꢒꢏꢖꢏꢉꢍꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢊꢐꢍꢀꢁꢙꢀꢍꢋꢌꢍꢂꢀꢁꢂꢀꢏꢈꢄꢀꢐꢋꢏꢂꢋꢇꢈꢉꢀ\ꢊꢇꢒꢐꢔꢀꢀ
Xꢏꢖꢏꢉꢍꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢋꢏꢖꢓꢍꢂꢇꢈꢉꢀꢎꢇꢋꢌꢀꢍꢈꢉꢇꢈꢍꢀꢐꢓꢍꢍꢒꢀꢉꢁꢗꢍꢂꢈꢁꢂꢀꢁꢂꢀꢍꢖꢇꢐꢐꢇꢁꢈꢀꢑꢁꢖꢓꢁꢈꢍꢈꢋꢐꢛꢀꢁꢂꢀꢂꢊꢈꢈꢇꢈꢉꢀꢍꢈꢉꢇꢈꢍꢐꢀꢏꢃꢁꢗꢍꢀꢐꢓꢍꢑꢇꢅꢍꢒꢀꢏꢈꢒꢀꢂꢍꢑꢁꢖꢖꢍꢈꢒꢍꢒꢀ
engine speeds as listed in your operator’s manual.
#ꢀ
#ꢀ
#ꢀ
#ꢀ
#ꢀ
#ꢀ
$ꢓꢍꢂꢏꢋꢇꢁꢈꢀꢁꢙꢀꢋꢌꢍꢀꢊꢈꢇꢋꢀꢎꢇꢋꢌꢀꢇꢖꢓꢂꢁꢓꢍꢂꢆꢄꢀꢖꢏꢇꢈꢋꢏꢇꢈꢍꢒꢂꢍꢖꢁꢗꢍꢒꢀꢑꢊꢋꢋꢇꢈꢉꢀꢐꢌꢇꢍꢆꢒꢀꢁꢂꢀꢂꢍꢖꢁꢗꢍꢒꢒꢏꢖꢏꢉꢍꢒꢀꢏꢇꢂꢀꢅꢆꢋꢍꢂꢔꢀꢀ
Xꢏꢖꢏꢉꢍꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢒꢇꢂꢋꢛꢀꢓꢂꢍꢐꢐꢊꢂꢍꢀꢁꢂꢀꢐꢋꢍꢏꢖꢀꢑꢆꢍꢏꢈꢇꢈꢉꢀꢋꢌꢍꢀꢊꢈꢇꢋꢛꢀꢐꢏꢆꢋꢀꢎꢏꢋꢍꢂꢛꢀꢑꢁꢂꢂꢁꢐꢇꢁꢈꢛꢀꢂꢊꢐꢋꢛꢀꢗꢏꢂꢈꢇꢐꢌꢛꢀꢏꢃꢂꢏꢐꢇꢗꢍꢐꢛꢀꢏꢈꢒꢀꢖꢁꢇꢐꢋꢊꢂꢍꢔ
Xꢍꢙꢍꢑꢋꢐꢛꢀꢖꢏꢆꢙꢊꢈꢑꢋꢇꢁꢈꢐꢀꢁꢂꢀꢙꢏꢇꢆꢊꢂꢍꢐꢀꢂꢍꢐꢊꢆꢋꢇꢈꢉꢀꢙꢂꢁꢖꢀꢏꢃꢊꢐꢍꢛꢀꢖꢇꢐꢊꢐꢍꢛꢀꢈꢍꢉꢆꢍꢑꢋꢛꢀꢖꢁꢒꢇꢅꢑꢏꢋꢇꢁꢈꢐꢛꢀꢏꢆꢋꢍꢂꢏꢋꢇꢁꢈꢐꢛꢀꢈꢁꢂꢖꢏꢆꢀꢎꢍꢏꢂꢛꢀꢇꢖꢓꢂꢁꢓꢍꢂꢀꢐꢍꢂꢗꢇꢑꢇꢈꢉꢛꢀꢁꢂꢀꢊꢐꢍꢀ
of unauthorized attachments.
#ꢀ
#ꢀ
@ꢈꢑꢁꢂꢂꢍꢑꢋꢀꢐꢋꢁꢂꢏꢉꢍꢀꢓꢂꢁꢑꢍꢒꢊꢂꢍꢐꢛꢀꢐꢋꢏꢆꢍꢀꢙꢊꢍꢆꢛꢀꢇꢈꢑꢆꢊꢒꢇꢈꢉꢀꢙꢏꢇꢆꢊꢂꢍꢀꢋꢁꢀꢓꢂꢁꢗꢇꢒꢍꢀꢁꢂꢀꢓꢍꢂꢙꢁꢂꢖꢀꢂꢍ€ꢊꢇꢂꢍꢒꢀꢖꢏꢇꢈꢋꢍꢈꢏꢈꢑꢍꢀꢐꢍꢂꢗꢇꢑꢍꢐꢀꢏꢐꢀꢓꢂꢍꢐꢑꢂꢇꢃꢍꢒꢀꢇꢈꢀꢋꢌꢍꢀꢁꢓꢍꢂꢏꢋꢁꢂꢐꢀ
manual. Preventative maintenance as outlined in the operators manual is the customer’s responsibility.
'ꢏꢇꢆꢊꢂꢍꢐꢀꢒꢊꢍꢀꢋꢁꢀꢇꢖꢓꢂꢁꢓꢍꢂꢀꢐꢍꢋ*ꢊꢓꢛꢀꢓꢂꢍ*ꢒꢍꢆꢇꢗꢍꢂꢄꢀꢐꢍꢂꢗꢇꢑꢍꢀꢁꢂꢀꢂꢍꢓꢏꢇꢂꢀꢐꢍꢂꢗꢇꢑꢍꢀꢃꢄꢀꢏꢈꢄꢁꢈꢍꢀꢁꢋꢌꢍꢂꢀꢋꢌꢏꢈꢀꢏꢊꢋꢌꢁꢂꢇ%ꢍꢒꢀ!"#$ꢀꢐꢍꢂꢗꢇꢑꢇꢈꢉꢀꢒꢍꢏꢆꢍꢂꢀꢒꢊꢂꢇꢈꢉꢀꢋꢌꢍꢀ
warranty period.
"ꢍꢂꢋꢏꢇꢈꢀparts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups.
Bꢐꢍꢀꢁꢙꢀꢐꢓꢏꢂꢘꢀꢓꢆꢊꢉꢐꢀꢁꢋꢌꢍꢂꢀꢋꢌꢏꢈꢀꢋꢌꢁꢐꢍꢀꢖꢍꢍꢋꢇꢈꢉꢀꢓꢍꢂꢙꢁꢂꢖꢏꢈꢑꢍꢀꢏꢈꢒꢀꢒꢊꢂꢏꢃꢇꢆꢇꢋꢄꢀꢂꢍ€ꢊꢇꢂꢍꢖꢍꢈꢋꢐꢀꢁꢙꢀꢋꢌꢍꢀ$!/ꢀꢐꢓꢏꢂꢘꢀꢓꢆꢊꢉꢀꢆꢇꢐꢋꢍꢒꢀꢇꢈꢀꢋꢌꢍꢀ$ꢓꢍꢂꢏꢋꢁꢂꢐꢀ
Manuals.
$ꢗꢍꢂꢌꢍꢏꢋꢇꢈꢉꢀꢁꢂꢀꢑꢏꢂꢃꢁꢈꢀꢐꢑꢁꢂꢇꢈꢉꢀꢙꢏꢇꢆꢊꢂꢍꢐꢀꢒꢊꢍꢀꢋꢁꢀꢂꢍꢐꢋꢂꢇꢑꢋꢍꢒꢛꢀꢑꢆꢁꢉꢉꢍꢒꢀꢍꢜꢌꢏꢊꢐꢋꢀꢓꢁꢂꢋꢀꢁꢂꢀꢑꢁꢖꢃꢊꢐꢋꢇꢁꢈꢀꢑꢌꢏꢖꢃꢍꢂꢛꢀꢇꢈꢑꢆꢊꢒꢇꢈꢉꢀꢒꢏꢖꢏꢉꢍꢀꢋꢁꢀꢐꢓꢏꢂꢘꢀꢏꢂꢂꢍꢐꢋꢍꢂꢀ
screen.
#ꢀ
#ꢀ
#ꢀ
#ꢀ
#ꢀ
<ꢒƒꢊꢐꢋꢖꢍꢈꢋꢐꢀꢏꢙꢋꢍꢂꢀꢋꢌꢍꢀꢅꢂꢐꢋꢀ[^J]ꢀꢋꢌꢇꢂꢋꢄꢀꢒꢏꢄꢐꢀꢏꢈꢒꢀꢃꢍꢄꢁꢈꢒꢛꢀꢐꢊꢑꢌꢀꢏꢐꢀꢑꢏꢂꢃꢊꢂꢍꢋꢁꢂꢀꢏꢒƒꢊꢐꢋꢖꢍꢈꢋꢀꢏꢈꢒꢀꢋꢌꢂꢁꢋꢋꢆꢍꢀꢑꢏꢃꢆꢍꢀꢏꢒƒꢊꢐꢋꢖꢍꢈꢋꢔꢀ
Xꢏꢖꢏꢉꢍꢀꢋꢁꢀꢉꢍꢏꢂꢐꢀꢁꢂꢀꢉꢍꢏꢂꢀꢑꢏꢐꢍꢐꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢑꢁꢈꢋꢏꢖꢇꢈꢏꢋꢍꢒꢀꢉꢂꢍꢏꢐꢍꢀꢁꢂꢀꢁꢇꢆꢛꢀꢊꢐꢍꢀꢁꢙꢀꢇꢈꢑꢁꢂꢂꢍꢑꢋꢀꢋꢄꢓꢍꢀꢁꢂꢀꢗꢇꢐꢑꢁꢐꢇꢋꢄꢀꢁꢙꢀꢆꢊꢃꢂꢇꢑꢏꢈꢋꢐꢛꢀꢏꢈꢒꢁꢂꢀꢙꢏꢇꢆꢊꢂꢍꢀꢋꢁꢀꢑꢁꢖꢓꢆꢄꢀ
with recommended grease or oil change intervals.
#ꢀ
#ꢀ
#ꢀ
Xꢏꢖꢏꢉꢍꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢆꢁꢏꢒꢇꢈꢉꢀꢚ#ꢕ!Xꢀ?ꢀ„<"® beyond recommended capacity.
Xꢏꢖꢏꢉꢍꢀꢑꢏꢊꢐꢍꢒꢀꢃꢄꢀꢓꢊꢖꢓꢀꢁꢂꢀꢐꢓꢂꢏꢄꢍꢂꢀꢂꢊꢈꢈꢇꢈꢉꢀꢒꢂꢄꢛꢀꢓꢊꢖꢓꢇꢈꢉꢀꢁꢂꢀꢐꢓꢂꢏꢄꢇꢈꢉꢀꢑꢏꢊꢐꢋꢇꢑꢀꢁꢂꢀ\ꢏꢖꢖꢏꢃꢆꢍꢀꢖꢏꢋꢍꢂꢇꢏꢆꢐꢛꢀꢁꢂꢀꢆꢏꢑꢘꢀꢁꢙꢀꢁꢂꢀꢃꢂꢁꢘꢍꢈꢀꢐꢋꢂꢏꢇꢈꢍꢂꢐꢔꢀ
<ꢒꢒꢇꢋꢇꢁꢈꢏꢆꢀꢒꢏꢖꢏꢉꢍꢀꢋꢁꢀꢓꢏꢂꢋꢐꢀꢁꢂꢀꢑꢁꢖꢓꢁꢈꢍꢈꢋꢐꢀꢒꢊꢍꢀꢋꢁꢀꢑꢁꢈꢋꢇꢈꢊꢍꢒꢀꢊꢐꢍꢀꢏꢙꢋꢍꢂꢀꢁꢓꢍꢂꢏꢋꢇꢁꢈꢏꢆꢀꢓꢂꢁꢃꢆꢍꢖꢀꢁꢂꢀꢙꢏꢇꢆꢊꢂꢍꢀꢁꢑꢑꢊꢂꢐꢔꢀꢚꢌꢁꢊꢆꢒꢀꢁꢓꢍꢂꢏꢋꢇꢁꢈꢏꢆꢀꢓꢂꢁꢃꢆꢍꢖꢀꢁꢂꢀ
failure occur, the product should not be used, but delivered as is to an authorized ECHO servicing dealer.
It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your ECHO product or by visiting
WWW.ECHO-USA.COMꢔꢀZꢁꢊꢂꢀꢂꢍꢑꢍꢇꢓꢋꢀꢁꢙꢀꢓꢊꢂꢑꢌꢏꢐꢍꢀꢇꢈꢑꢆꢊꢒꢇꢈꢉꢀꢒꢏꢋꢍꢛꢀꢖꢁꢒꢍꢆꢀꢏꢈꢒꢀꢐꢍꢂꢇꢏꢆꢀꢈꢊꢖꢃꢍꢂꢀꢖꢊꢐꢋꢀꢃꢍꢀꢖꢏꢇꢈꢋꢏꢇꢈꢍꢒꢀꢏꢈꢒꢀꢓꢂꢍꢐꢍꢈꢋꢍꢒꢀꢋꢁꢀꢏꢈꢀꢏꢊꢋꢌꢁꢂꢇ%ꢍꢒꢀ
ECHO servicing dealer for warranty service. Proof of purchase rests solely with the customer. Some states do not allow limitations on how long
an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the exclusion or limitation of incidental or
ꢑꢁꢈꢐꢍ€ꢊꢍꢈꢋꢇꢏꢆꢀꢒꢏꢖꢏꢉꢍꢐꢛꢀꢐꢁꢀꢄꢁꢊꢀꢖꢏꢄꢀꢏꢆꢐꢁꢀꢌꢏꢗꢍꢀꢁꢋꢌꢍꢂꢀꢐꢓꢍꢑꢇꢅꢑꢀꢆꢍꢉꢏꢆꢀꢂꢇꢉꢌꢋꢐꢀꢎꢌꢇꢑꢌꢀꢗꢏꢂꢄꢀꢙꢂꢁꢖꢀꢐꢋꢏꢋꢍꢀꢋꢁꢀꢐꢋꢏꢋꢍꢔꢀ9ꢌꢇꢐꢀꢆꢇꢖꢇꢋꢍꢒꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢇꢐꢀꢉꢇꢗꢍꢈꢀꢃꢄꢀ!"#$ꢀ
Incorporated, 400 Oakwood Rd., Lake Zurich, IL 60047.
DISCLAIMER OF IMPLIED WARRANTIES
9ꢌꢇꢐꢀꢆꢇꢖꢇꢋꢍꢒꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢇꢐꢀꢇꢈꢀꢆꢇꢍꢊꢀꢁꢙꢀꢏꢆꢆꢀꢁꢋꢌꢍꢂꢀꢍꢜꢓꢂꢍꢐꢐꢍꢒꢀꢁꢂꢀꢇꢖꢓꢆꢇꢍꢒꢀꢎꢏꢂꢂꢏꢈꢋꢇꢍꢐꢛꢀꢇꢈꢑꢆꢊꢒꢇꢈꢉꢀꢏꢈꢄꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢁꢙꢀ'@9?!ꢚꢚꢀ'$ꢕꢀ<ꢀ><ꢕ9@"B:<ꢕꢀ>Bꢕ>$ꢚ!ꢀ
OR USE and any implied warranty of MERCHANTABILITYꢀꢁꢋꢌꢍꢂꢎꢇꢐꢍꢀꢏꢓꢓꢆꢇꢑꢏꢃꢆꢍꢀꢋꢁꢀꢋꢌꢇꢐꢀꢓꢂꢁꢒꢊꢑꢋꢔꢀ!"#$ꢀꢏꢈꢒꢀꢇꢋꢐꢀꢏꢙꢅꢆꢇꢏꢋꢍꢒꢀꢑꢁꢖꢓꢏꢈꢇꢍꢐꢀꢐꢌꢏꢆꢆꢀꢈꢁꢋꢀꢃꢍꢀ
ꢆꢇꢏꢃꢆꢍꢀꢙꢁꢂꢀꢏꢈꢄꢀꢐꢓꢍꢑꢇꢏꢆꢀꢇꢈꢑꢇꢒꢍꢈꢋꢏꢆꢀꢁꢂꢀꢑꢁꢈꢐꢍ€ꢊꢍꢈꢋꢇꢏꢆꢀꢒꢏꢖꢏꢉꢍꢛꢀꢇꢈꢑꢆꢊꢒꢇꢈꢉꢀꢆꢁꢐꢋꢀꢓꢂꢁꢅꢋꢐꢔꢀ9ꢌꢍꢂꢍꢀꢏꢂꢍꢀꢈꢁꢀꢎꢏꢂꢂꢏꢈꢋꢇꢍꢐꢀꢍꢜꢋꢍꢈꢒꢍꢒꢀꢁꢋꢌꢍꢂꢀꢋꢌꢏꢈꢀꢏꢐꢀꢓꢂꢁꢗꢇꢒꢍꢒꢀꢌꢍꢂꢍꢇꢈꢔꢀ
9ꢌꢇꢐꢀꢆꢇꢖꢇꢋꢍꢒꢀꢎꢏꢂꢂꢏꢈꢋꢄꢀꢖꢏꢄꢀꢃꢍꢀꢖꢁꢒꢇꢅꢍꢒꢀꢁꢈꢆꢄꢀꢃꢄꢀ!"#$ꢔ
99922201032
11/18/2011
X7531125002
33
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
PB-760 LN H/T
NOTES
34
X7531125002
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PB-760 LN H/T
NOTES
X7531125002
35
© 03/2013 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
(T) P39611001001/P39611999999
(T) P37912002001/P37912999999
(H) P39511001001/P39511999999
(H) P37812002001/P37812999999
36
Download from Www.Somanuals.com. All Manuals Search And Download.
|
