GFDS350GL/GFDS355GL
GE® 7.5 cu. ft. stainless steel capacity frontload dryer with Steam
Dimensions and Installation Information (in inches)
27
33
Gas Dryer Rating
60Hz, 6A
1-5/8
120V
Exhaust Options: 3-way via rear, left, and bottom.
Circuit Requirements: An individual, properly grounded
branch circuit, protected by a 15-20 amp circuit breaker
or a time-delay fuse, is required.
Note: Dryer wall outlet must be located within 36”
of service cord entry and accessible when dryer is
mounted in position.
40-1/2
Installation Information: For complete information, see
installation instructions packed with your dryer.
3-3/4
5-1/2
For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
ge.com or call GE Answer Center® service,
800.626.2000.
Specification Revised 10/10
360482
Download from Www.Somanuals.com. All Manuals Search And Download.
GFDS350GL/GFDS355GL
GE® 7.5 cu. ft. stainless steel capacity frontload dryer with Steam
Dryer Exhausting Information – Metal Duct Only
For complete information, see installation instructions packed with your dryer.
Best performance
Maximum length of 4"
dia. rigid metal duct
Ducting Materials: For best performance, this dryer should be vented with 4” diameter
all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible
metal (semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may
be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct.
A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid
metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4” diameter can
be maintained throughout the entire length of the transition duct. Please see installation
instruction packed with your dryer for complete instructions when using flexible metal (foil
type) ducting.
A
A
Exhaust hood type
4
B
Number
of
A
4"
B
90°
Domestic
dryer models
2-1/2"
opening
2-1/2
turns
opening
0
1
2
3
90 ft.
60 ft.
45 ft.
35 ft.
60 ft.
45 ft.
35 ft.
25 ft.
Exhaust Length Calculation:
7.0, 6.0 and 5.8 cu. ft.
capacity models
all gas dryers
1. Determine the number of 90° turns needed for your installation. If you exhaust to the
side or bottom of dryer, add one turn.
2. The maximum length of 4’ rigid (aluminum or galvanized) duct which can be tolerated is
shown in the table.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should be
treated as a 90° elbow.
A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed
house floor (crawl space), or into an attic, since the accumulated lint could create a fire
hazard or moisture could cause damage. Never terminate the exhaust into a common duct
or plenum with a kitchen exhaust, since the combination of lint and grease could create a
fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird
nesting, etc. The wall cap must also be located at least 12" above the ground or any other
obstruction with the opening pointed down.
For more information on venting kits and accessories, please call 1-800-GE-CARES.
Specification Revised 10/10
360482
Download from Www.Somanuals.com. All Manuals Search And Download.
GFDS350GL/GFDS355GL
GE® 7.5 cu. ft. stainless steel capacity frontload dryer with Steam
Features and Benefits
• Steam Refresh/Steam Dewrinkle - Steam Refresh helps reduce wrinkles, odors and
rejuventates fabrics, while Steam Dewrinkle reduces wrinkles and freshens clean
clothes
• Sensor Dry Plus™ - Innovative moisture-sensing technology helps maintain quality
• eDry option - Energy-saving option reduces dry temperatures on select cycles
without sacrificing performance
• Active Wear cycle - Specific settings to take special care of clothing worn for active
sports exercise
• My Cycles - Custom cycle that can be set for specific or frequent needs
• Speed Dry - Quickly dries items and small loads for families on the go
• 1- 24-hour Delay Start - Set the dryer to begin cycles whenever it’s convenient for you
• Up to 90 ft. venting capability - Has long equivalent ducting performance for more
flexible installation
• Up to 90 ft. venting capability - Has long equivalent ducting performance for more
flexible installation
• Model GFDS355GLMS – Metallic silver
• Model GFDS350GLWW – White on white
• Model GFDS355GLMV – Vermillion Red
Specification Revised 10/10
360482
Download from Www.Somanuals.com. All Manuals Search And Download.
|