C150-E200-02EN
fi-4750L Image Scanner
Operator's Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
fi-4750L
Image Scanner
Operator's Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Revisions, Disclaimers
Editon
01
Date published
March, 2001
March, 2001
Revised contents
First edition
02
Partly changed
i, ii, 1-9, 2-7, 4-4,
DE-1, DE-2
Specification No. C150-E200-02EN
FCC declaration: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidential
installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturning
the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC warning: Changes or modifications not expressly approved by the party respon-
sible for compliance could void the user's authority to operate the equipment.
NOTICE
• The use of a non-shielded interface cable with the referenced device is prohibited.
Thelengthoftheparallelinterfacecablemustbe3meters(10feet)orless.Thelength
of the serial interface cable must be 15 meters (50 feet) or less.
• The length of the power cord must be 3 meters (10 feet) or less.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
This Class B digital apparatus complies with Canadian ICES-003.
CetappareilnumériquedelaclasseBestconformmeàlanormeNMB-003duCanada.
As an ENERGYSTAR ® Partner, Fujitsu Limited has determined that this scanner meets
®
®
ENERGYSTAR
guidelines for energy efficiency. ENERGYSTAR
is a
U. S. registered mark.
The contents of this manual may be revised without prior notice.
All Rights Reserved, Copyright © 2001 FUJITSU LIMITED.
Printed in Japan.
No part of this manual may be reproduced in any form without permission.
Warning on use requiring extremely high safety levels
This Product is designed, developed and manufactured as contemplated for general
use, including without limitation, general office use, personal use and household use,
but is not designed, developed and manufactured as contemplated for use accompa-
nying fatal risks or dangers that, unless extremely high safety is secured, could lead
directly to death, personal injury, severe physical damage or other loss (hereinafter
“High Safety Required Use”), including without limitation, nuclear power core control,
airplane control, air traffic control, mass transport operation control, life support,
weaponlaunchingcontrol.YoushallnotusethisProductwithoutsecuringthesufficient
safetyrequiredfortheHighSafetyRequiredUse.IfyouwishtousethisProductforHigh
Safety Required Use, please consult with our sale person in charge before such use.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Fujitsu Offices
Please send your comments on this manual or on Fujitsu products to the following
addresses:
FUJITSU COMPUTER PRODUCTS OF
AMERICA,INC.
2904 Orchard Parkway,San Jose.
California 95134-2022,U.S.A.
TEL:1-408-432-6333
FUJITSU FRANCE S.A.
I, Place des Etats-Unis, SILIC 310,
94588 Rungis cedex, FRANCE
TEL:33-1-4180-3880
FAX:33-1-4180-3866
FAX:1-408-432-3908
FUJITSU COMPUTERS (SINGAPORE) PTE,
LTD.
20 Science Park Road #03-01, Tele Teck Park
Singapore Science Park II, Singapore 117674
Republic of Singapore
FUJITSU AUSTRALIA LIMITED
Fujitsu Hause 2 Julius Avenue North Ryde
N.S.W 2113 AUSTRALIA
TEL:61-2-9776-4555
FAX:61-2-9776-4019
TEL:65-777-6577
FAX:65-771-5669
FUJITSU CANADA,INC.
2800 Matheson Blvd.East,Mississauga.
Ontario L4W 4X5,CANADA
TEL:1-905-602-5454
FUJITSU HONG KONG Limited
10/F, Lincoln House, Taikoo Place,
979 King’s Road, Island East, Hong Kong
TEL:852-827-5780
FAX:1-905-602-5457
FAX:852-827-4724
TLX:62667
FUJITSU DEUTSCHLAND GmbH.
Frankfurter Ring 211,
8000 München 40,F.R,GERMANY
TEL:49-89-32378-0
FUJITSU ITALIA S.p.A.
Via Nazario Sauro, 38
FAX:49-89-32378-100
20099 Sestos, Giovanni (MI), ITALY
TEL:39-2-26294-1
FAX:39-2-26294-201
FUJITSU ESPAÑA,S.A
Edificio torre Europa 5a
Paseo de la Castellana 95
Madrid 28046,SPAIN
FUJITSU NORDIC AB
Kung Hans väg,S-192 68 Sollentuna, SWEDEN
TEL:46-8-626-4500
TEL:34-1-581-8000
FAX:34-1-581-8300
FAX:46-8-626-4588
FUJITSU EUROPE LTD.
FUJITSU LIMITED
2,Longwalk Road,Stockey Park,Uxbridge
Middlesex,UB11 1AB,U.K
TEL:44-81-573-4444
International Operations
Marunouchi 1-6-1, Chiyoda-ku,
Tokyo 100 JAPAN
FAX:44-81-573-2643
TEL:(81-3)3216-3211
FAX:(81-3)3213-7174
TLX:J2283
Cable:”FUJITSU LIMITED TOKYO”
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Note, Liability
READ ALL OF THIS MANUAL CAREFULLY BEFORE USING THIS PRODUCT. IF
NOT USED CORRECTLY, UNEXPECTED INJURY MAY BE CAUSED TO USERS
OR BYSTANDERS.
Whilealleffortshavebeenmadetoensuretheaccuracyofallinformationinthismanual,
FUJITSU assumes no liability to any party for any damage caused by errors or
omissions or by statements of any kind in this manual, its updates or supplements,
whethersucherrorsareomissionsorstatementsresultingfromnegligence,accidents,
or any other cause. FUJITSU further assumes no liability arising from the application
or use of any product or system described herein; nor any liability for incidental or
consequential damages arising from the use of this manual. FUJITSU disclaims all
warranties regarding the information contained herein, whether expressed, implied, or
statutory.
FUJITSU reserves the right to make changes to any products herein, to improve
reliability, function, or design, without further notice and without obligation.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
This manual explains how to use the fi-4750L image scanner.
This manual contains chapters on the following topics:
COMPONENTS
INSTALLATION AND CONNECTIONS
OPERATING INSTRUCTIONS
ADF DOCUMENT SPECIFICATIONS
SCANNER SPECFICATIONS
SETUP MODE
It also contains a Glossary of Terms and an Index.
Refer to the Cleaning and Maintenance Guide for information about the routine
operation of the fi-4750L.
TheReferenceGuidecontainschaptersonOPERATINGINSTRUCTIONS,CLEAN-
ING, REPLACEMENT OF PARTS, ADJUSTMENT and TROUBLESHOOTING.
The fi-4750L is a very fast and highly functional image scanner developed for
volume filing, using charge-coupled device (CCD) image sensors. This scanner
features duplex scanning and high quality image processing with an automatic
document feeder (ADF).
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Conventions
Important information that requires special attention is indicated as follows:
WARNING
WARNING indicates that personal injury like pinching of fingers or hands may result if
you do not follow a procedure correctly.
CAUTION
CAUTION indicates that damage to the scanner may result if you do not follow a
procedure correctly.
Official Fujitsu part names are indicated with an initial capital letter, as in the part name
“Pick roller”.
NOTICE
A NOTICE provides “how-to” tips or suggestions to help you perform a procedure
correctly.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
❑ CHAPTER 1 COMPONENTS
Checking the Components............................................... 1-1
Units and Assemblies ...................................................... 1-2
Operator Panel................................................................. 1-5
❑ CHAPTER 2 INSTALLATION AND CONNECTIONS
Precautions...................................................................... 2-1
Inspection ........................................................................ 2-2
Repositioning the Shipping Lock ...................................... 2-3
Cable Connections .......................................................... 2-4
Mounting the Stacker ....................................................... 2-6
Setting the SCSI ID and the SCSI Terminator .................. 2-7
❑ CHAPTER 3 OPERATING INSTRUCTION
Turning the Power On ...................................................... 3-1
Waking up the Scanner from the Low Power Mode.......... 3-2
Manual Feed Mode Setting .............................................. 3-3
Loading Documents on the ADF ...................................... 3-4
Loading Documents on the Flatbed ................................. 3-8
Reading a Page from a Thick Book .................................. 3-9
❑ CHAPTER 4 ADF DOCUMENT SPECIFICATION
Document Size ................................................................ 4-1
Document Quality ............................................................ 4-2
ADF Document Feeder Capacity ..................................... 4-4
Areas not to be Perforated ............................................... 4-5
Grounding Color Areas .................................................... 4-6
Double Feed Detection Condition .................................... 4-7
Job Separation Sheet ...................................................... 4-8
❑ CHAPTER 5 SCANNER SPECIFICATIONS
Basic Product Specification ............................................. 5-1
Installation Specification .................................................. 5-2
Dimensions ...................................................................... 5-3
❑ CHAPTER 6 CONSUMABLES AND OPTIONS
Consumables ................................................................... 6-1
Options ............................................................................ 6-2
Video Interface Option ..................................................... 6-3
IPC-4D Option ................................................................. 6-7
❑ CHAPTER 7 SETUP MODE
Activating the Setup Mode ............................................... 7-1
Contents of the Setup Mode ............................................ 7-2
❑ GLOSSARY OFTERMS ....................................................................... GL-1
❑ INDEX ...................................................................................... IN-1
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENTS
COMPONENTS
INSTALLATION AND CONNECTIONS
OPERATING INSTRUCTION
DOCUMENT SPECIFICATION
SCANNER SPECIFICATIONS
CONSUMABLES AND OPTIONS
SETUP MODE
INSTALLATION AND
CONNECTIONS
OPERATING
INSTRUCTION
DOCUMENT
SPECIFICATION
SCANNER
SPECIFICATIONS
CONSUMABLES
AND OPTIONS
SETUP MODE
GLOSSARY
OF TERMS
GLOSSARY OFTERMS
INDEX
INDEX
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER
1
COMPONENTS
This chapter describes the components of the scanner, part names, operator
panel arrangement, and the function of parts and LED indicators. After
unpacking the scanner, confirm that all components have been received by
checking them against the list in the first section.
Checking the Components
Units and Assemblies
Operator Panel
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the Components
These high precision components must be handled carefully.
Confirm that all the components shown in the following figure have been received.
1
If any component is missing, please contact your sales agent.
Scanner
Power cable
for North America
Power cable
for Europe
Manuals and Driver
Pad ASY
Chute cable
Chute rollers
(two rollers)
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Units and Assemblies
This section shows the exterior view and assemblies of the scanner. This section also provides the name
of each part and describes its functions.
Units
8
7
Document cover
Document holding pad
2
3
1
Paper weight
(hidden)
ADF
ADF paper chute
6
5
4
Stacker
ADF
Oparator panel
lever
9
Document bed
11
10
12
INT connector
IMP connector
Third party slot
16
Power switch
15
13
Interface connector
14
Power inlet
EXT connector
fi-4750L
NOTICE
The shipping lock must be switched to the operating position before the scanner can be used. Refer to
page 2-4.
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
No
Function
Automatically feeds documents to the reading position.
Presses the documents loaded on the ADF paper chute.
Holds the documents to be fed by the ADF.
1
2
3
4
Displays the status of the scanner. Also displays buttons that enable the
operator to change settings in Feed mode, Manual Feed mode, and Setup
mode.
5
Opens/closes ADF to enable the removal of jammed documents.
Stacks the read documents.
6
7
8
9
Presses the document to the Document bed.
Closes over and keeps in place the document to be read.
Holds the document to be read. Also called Flatbed (FB).
Connects to an option.
10
11
12
Connects to the EXT connector.
A Fujitsu Video Interface Option Board is installed.
Connects to the host system with interface cables.
Connects to the INT connector.
13
14
15
Connects to an AC power outlet with the power cable.
Turns the power On or Off.
16
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assemblies
Adjustment
stacker
Thumb screw
Guide A
ASY
Pick roller 2
Stacker
Pick roller 1
Chute
roller
Pad ASY
Roller
cover
Chute
roller
Roller
cover
Gate ASY
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Operator Panel
The operator panel is located on the upper right hand side of the scanner. The panel consists of an
LCD display (16 characters x 2 lines), LEDs and buttons.
Arrangement
Operator panel
Previous
Exit
Stop
Send To/
Start
Read
Enter
Check
Next
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Button/LED Function
Name of the button and
LED
Function
Button
Next
Displays the next LCD screen.
Displays the previous LCD screen.
Moves the cursor to the left.
Moves the cursor to the right.
Previous
Exit
When you are entering settings on the Operator panel, pressing this button
returns you immediately to the Scanner Ready screen.
Enter
Enters the parameter currently selected by the cursor.
Send To/
Start
Operational only when Manual start mode is set or the Read lamp lights; Starts
the reading when video interface option is used. Some application software
packages make use of this button.
Stop
When the Check LED lights, pressing this button releases the error status
(turns off Check and returns to the Scanner Ready screen).
Operational only during the reading operation; stops the reading when the video
interface option is used.
Also turns off the Check lamp.
LED
Indicates that the scanner is On.
Read
Indicates the scanner is reading or ready to read.
Check
If lit, this indicates that an alarm occurred. Pressing the Stop button
turns the Check lamp Off.
If it blinks at one second intervals, this means that a jam or double feed
has been detected. If the problem is jammed paper, removing the jammed
paper turns off the Check lamp. If the problem is double feed, pressing
the Stop button turns off the Check lamp.
If it blinks at four seconds intervals, this means that cleaning the ADF is
necessary.
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Counter Display
The scanner is provided with a counter display.
Paper counter
Abrasion counter
Counter
Function
Paper counter
When the
The paper counter counts the number of scanned sheets
button is pressed from the start of reading until Paper Empty or an error is
detected. The counter is automatically reset at the start
of reading. The counter is used for checking the
number of the sheets scanned in one batch.
When the
This counter increments each time a document is
button is pressed scanned. It is not initialized until the power is turned off.
The counter can be used, for example, for checking the
number of sheets that have been scanned in one day.
Abrasion counter The abrasion counter counts the accumulated number of scanned sheets.
This counter increments every 10 sheets. It is useful to check the cleaning
cycle or the parts replacement cycle. How to reset it is described in Chapter
6.
NOTICE
When the counter value is 0, no number is displayed.
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation status
The operation status is indicated by the following messages:
<Power-on>
<Reading>
<Waiting for Start>
The scanner displays the following screen when waiting for the
Start button to be pressed:
(Only When the Video Interface
Option is installed.)
<Cleaning request>
When the Pick roller cleaning is necessary, the scanner displays
the following on the upper line:
When the ADF glass cleaning is necessary, the scanner displays
the following on the LCD:
Clean the Pick roller or the ADF glass in accordance with the
manual, “Cleaning and Maintenance”.
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Temporary error
<Hopper empty>
This message is displayed if there is no more paper on the ADF
paper chute during a read operation in ADF mode. Fill the ADF
paper chute with paper. To enable the read operation, press the
stop button.
<Jam>
This message is displayed if a document is jammed in the ADF.
See the “Cleaning and Maintenance” manual. (“Cleaning paper
jams” “Symptom 11” “Symptom 12”)
<ADF cover open>
<Double feed error>
This message is displayed if the ADF is not closed completely.
Close the ADF completely, and enable the read operation.
This message is displayed when the ADF detects the Double feed
error. Check the document and re-scan the document.
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm
One of the following messages is displayed if an error occurs in the scanner. If one of the following
error messages is displayed, turn the power Off and then On again. If the same message is displayed,
contact your service representative.
<Optical alarm front>
<Optical alarm back>
<FB mechanism alarm>
NOTICE
When the total number of sheets scanned by the ADF is less than 100, the message above and the
message below are displayed alternately. Remove the bracket (Shipping Lock) that holds the carrier
in place.
<Motor fuse alarm>
<Lamp fuse alarm>
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
<Image transfer alarm>
<Memory alarm>
<EEPROM alarm>
<FAN alarm>
<IPC Board alarm>
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
1-12
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER
2
INSTALLATION AND CONNECTIONS
The chapter describes how to install and connect the scanner.
Precautions
Inspection
Repositioning the Shipping Lock
Cable Connections
Mounting the Stacker
Setting the SCSI ID and the SCSI Terminator
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
This section describes precautions to follow when installing the scanner.
To ensure the longevity and proper functioning of your scanner, do not install the scanner in the places
and environments described below.
• Place the scanner away from electrical noise sources, strong magnetic fields, and air flow. If the scanner
is used near an air conditioner, copying machine, or TV set, the scanner may operate incorrectly.
• Keep the scanner out of the sun and away from heaters. These environments may shorten the scanner
life or cause hardware failures.
• Do not install the scanner in a place where vibrations may occur. This environment may cause
hardware failures or may cause the scanner to operate incorrectly.
• Do not install the scanner in humid, dusty, or damp places. These environments may shorten the
scanner life or cause hardware failures.
• Do not place the scanner where liquid spills may occur.
• Be aware of static electricity, which can damage the scanner’s sensitive electronic parts. Be sure the
flooring and the desk are made of materials that do not generate static electricity.
For information on the minimum required size of the installation space, see Chapter 5, “Specifications”.
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Inspection
This section describes how to check the labels.
Label A
Label B
Label A (Example; your actual label may differ)
Label B (Example; your actual label may differ)
Rev.
Label
MODEL
fi-4750L
A
B
C
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
PART NO.
SER. NO.
DATE
CAO2956 -2371
000003
2001-03
25 Kg
*
f
i
-
4
7
5
0 L
0
0
0
0
0
3
*
ANS
MADE IN JAPAN
FUJITSU LIMITED
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Repositioning the Shipping Lock
To keep the scanner from being damaged during shipping, the carrier unit is fixed with a Shipping Lock.
After placing the carrier unit where it will be installed, change the position of this Shipping Lock as
explained below.
Place the image scanner on the edge of the desktop so that the left side of the scanner (where the
ADF is attached) extends from the desktop. Do not set the image scanner upside down or on its
side.
1
CAUTION
Do not let the scanner hang more than 20 cm (8 in.) over the edge of the desk.
Good
less than 20 cm
Bad
Bad
(8 in.)
Remove the shipping lock from position
Front side
. Then, install the shipping lock at position
.
B
2
A
Front side
Enlarged
Shipping Lock
(Position for operation)
Bottom view
B
Shipping Lock
(Position for storage,
position for shipment)
Enlarged section A
ADF side
A
Shipping Lock
(Position for shipment)
CAUTION
Before moving or storing the scanner, make sure that the shipping lock is set to the
shipment position to prevent possible damage. Before setting the shipping lock, make sure
that the carrier has been returned to the home position.
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Connections
This section describes how to connect the cables.
Connect the cables as follows:
Turning the power switch Off
Press the “O” side of the power switch to turn the power Off.
Power OFF
Power ON
Power switch
Connecting the power cable
Connect the power cable to the power inlet of the device and a power outlet.
Power outlet
for North America
Power cable
Power inlet
for Europe
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the interface cables
Connect the SCSI interface cables and secure them.
Back of the image scanner
Interface
cables
To the host system
NOTICES
1. Factory default for the SCSI terminator is On. If the scanner is in the middle of the daisy chain or of two
devices, turn the scanner termination Off via the operator panel.
2. The factory default for the SCSI ID is 5. If the ID of the scanner is the same as the other device,
change the ID via the operator panel or change the ID of the other device.
Connecting the chute cable
Connect the chute cable.
To EXT (10-pin)
EXT (8-pin)
Chute cable
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Stacker
Mount the stacker using the following procedure.
Mount the stacker.
1
Hook the pins on the stacker to the claws on the image scanner.
Stacker
Claw
Pin (inside)
Mount the adjustment stacker.
2
Insert the four claws of the adjustment stacker into the four holes on the stacker, and push the
adjustment stacker towards the scanner.
Adjustment
stacker
Stacker
Four holes
Four claws
(Two are hidden)
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the SCSI ID and the SCSI Terminator
The default of the SCSI ID is 5. The SCSI ID is set by using the Setup mode of the operator panel. The
procedure to change the SCSI ID is as follows:
1 Turn the power On by
pressing the “I” side of the
power switch. The scanner
displays “Scanner Ready”
on the lower line of the LCD.
2 Press the “Next”
button.
The scanner displays “Mode
select 1”.
NOTICE
If the scanner have a video interface option, the scanner displays “Mode Select 0” on the LCD.
3 Press the “Next”
button
again. The scanner displays
“Mode select 2” meaning
that the setup mode is
ready.
4 Press the “Enter” button.
The scanner displays the
following:
5 Press the “Next”
button
ten. The scanner displays
“SCSI ID” on the upper line
of the LCD.
6 Select the desired SCSI ID by pressing the “ ”or “ ” buttons, and then pressing “Enter” (the SCSI
ID is set.)
7 Press “Exit” to return to the “Scanner Ready” screen if you don’t need to change the terminator.
NOTICE
If no other device is using the same SCSI ID, the scanner ID does not have to be changed.
NOTICE
The new ID does not take effect until the system power is turned On again.
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
8 Press “Next”
, the scanner
displays “Terminator” on the
upper line of the LCD.
Select “On” or “Off” by pressing
or
, then pressing “Enter”.
NOTICE
The scanner includes an internal SCSI terminator that can be turned On and Off from the operator panel of
the scanner. The factory default is “On.”
9 Press “Exit” to return to the “Scanner Ready” state.
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER
3
OPERATING INSTRUCTION
This chapter describes how to turn the power on, and gives button specifica-
tions and reading mode settings for both ADF and Manual modes, how to
load documents onto the ADF and Flatbed, how to load documents larger
than the Document bed, and how to read a page from a thick book.
Refer to the “Cleaning and Maintenance”manual for routine scanner mainte-
nance.
Turning the Power On
Waking up the Scanner from the Low Power Mode
Manual Feed Mode Setting
Loading Documents on the ADF
Loading Documents on the Flatbed
Reading a Page from a Thick Book
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the Power On
This section describes how to turn the power On.
Press the “I” side of the power switch. The power turns On and the green Power lamp at the operator
panel lights.
Power Off
Power switch
Power On
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Waking up the Scanner from the Low Power Mode
This section describes how to wake up the
scanner from the Low Power Mode.
To wake up the Scanner, simply press a
button, set the papers on the ADF, or send a
command to scan from the host computer.
NOTICE
®
As an ENERGYSTAR partner, Fujitsu Limited
declares that this scanner meets the
®
ENERGYSTAR guidelines for energy efficiency.
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual Feed Mode Setting
In this mode, the scanner waits for some predetermined time before issuing a “Paper Empty” message
after all documents are read. This predetermined time (time-out limit) is specified in the Setup mode.
Therefore, you can set the next documents on the ADF chute without interrupting the reading opera-
tion. The procedures for setting the manual feed mode are as follows:
<Screen M1>
1 Turn the power On and verify that
“Scanner Ready” is displayed on the
LCD.
<Screen M2>
2 Press
Screen M2.
then the scanner displays
NOTICE
The “Mode Select 0” screen is skipped when
your scanner is controlled through the SCSI
interface.
<Screen M3>
<Screen M4>
3 Press
Screen M3.
then the scanner displays
4 Press
Screen M4.
then the scanner displays
5 Select “Yes” by pressing . Then press
.
<Screen M1>
6 Press
to return to the “Scanner
Ready” screen. Note that “Manual Feed”
is shown on the LCD. This means that the
scanner is in Manual Feed mode.
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading Documents on the ADF
NOTICE
Be sure to change the position of the shipping lock according to the “Installation and Connection”
procedure before operation.
ADF paper chute
Guide
ADF
Guide lever
ADF lever
Stacker
Fan the sheets before setting a stack of
documents on the ADF paper chute.
Document
1
10mm
NOTICES
• Remove paper clips and staples. Flatten the staple holes.
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
• Read the following documents using the Flatbed:
- Paper with clips or staples.
- Paper written on with wet ink.
- Paper of uneven thickness (for example, envelopes).
- Paper with large rumples or curls.
- Paper with folds or tears.
- Tracing paper.
- Coated paper.
- Carbon paper.
- Paper smaller than A8 (portrait) size or wider than A3 size.
- Materials other than paper (for example, clothes, sheet metal, or OHP film).
- Photographic paper.
- Paper with perforations on the side.
- Non-rectangular paper.
- Very thin paper.
• Set documents on the ADF so that the curl of the leading edge does not exceed the measures shown
below.
More than 30mm
Less than
3mm
More than 30mm
Less than
5mm
Feed direction
Top of the paper
Read surface
Top of the paper
• To avoid skewing, do not feed documents of different widths during the same batch.
Preparing the Paper
2
• Place the documents face down, with the top to the left as shown in A. (The long side is the top for
landscape mode and the short side is the top for portrait mode.)
• Holding both ends with both hands, lift the documents.
• Hold the documents tightly with your left hand and bend them as shown in B.
• Grip the documents tightly with your right hand, loosen the grip of your left hand, and straighten as
shown in C.
• Even up the feed edge of the batch of paper as shown in D.
Top
A
B
D
(For portrait mode)
C
NOTICE
Reduce the batch size of the documents if double feed or mispick occurs.
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjust the stacker extension to the paper
size, and then flip out the plate.
3
4
ADF paper chute
Stacker
Set the guides so that there is a small
clearance between the document edges
and the guides. Load the document face
down on the ADF paper chute and adjust
the guides to the document width.
Documents
Guide lever
(Both sides)
Guide
NOTICE
When the paper weight falls down, lift and hold it
to load the documents.
Paper weight
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTICES
• Squeeze the guide lever to free the guides.
• Do not load document stacks thicker than
20 mm (0.8 in.) for A4/Letter or
10 mm (0.4 in.) for A3/11 x 17 in.
• Set the guides so that they touch the
document sides.
Max.
20 mm (0.8") or
10 mm (0.4")
See NOTICES.
Chute roller
WARNING
When a small size of documents are loaded on
the ADF paper chute, be careful not to pinch
your fingers or hands by the chute roller.
After the read command is issued from
5
the host system and the documents are
read, scanned documents are expelled
into the stacker for removal.
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading Documents on the Flatbed
WARNING
Do not look directly at the light source during the read operation.
Scanner parts involved when loading documents
Document cover
Document
holding pad
Document bed
Open the document cover.
1
Place the document face down and align
the top left corner with the reference
mark.
2
Reference mark
Slowly close the Document cover.
3
4
Issue the read command from the host
system.
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Reading a Page from a Thick Book
WARNING
Do not look directly at the light source during the read operation.
Thick book
Open the Document cover.
1
Place the book face down on the
Document bed.
2
Issue the read command from the host
system. Keep the cover open for the
reading operation.
3
NOTICE
Do not move the book during the read operation.
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
3-10
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER
4
ADF DOCUMENT SPECIFICATION
This chapter describes the document size and document guality required to
use the ADF successfully.
Document Size
Document Quality
ADF Document Feeder Capacity
Areas not to be Perforated
Grounding Color Areas
Double Feed Detection Condition
Job Separation Sheet
Download from Www.Somanuals.com. All Manuals Search And Download.
Document Size
The following figure shows document sizes that the scanner can read using the ADF.
Maximum
Scanner
Minimum
A
B
A
B
297 (11.7")
432 (17")
53 (2.1")
74 (2.9")
fi-4750L
A3/Double Letter
A8 (Portrait)
(Unit : mm)
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Document Quality
This section describes the types and weights of paper that the scanner can read and precautions in
preparing documents to ensure maximal scanner functioning.
Document type
The recommended paper type for documents is as follows:
• Woodfree paper
• Plain paper (for example, the paper type specified for XEROX 4024)
When using any other type of paper, test feed a few sheets with the ADF to ensure the paper feeds
properly before performing a large-scale reading operation.
Any paper can be used on the flatbed. However, the ground color specification must satisfy the
specification described in the Grounding Color Area section.
Paper weight
The paper weight should fall within the following ranges:
• 52 to 127 g/m2 (13.9 to 34 lb), 127g/m2 (34lb) for A8
Precautions
A preliminary document feed test may be necessary to avoid unexpected errors. If document slip or jam in
the ADF (JAM error) or double feed occurs frequently, read the documents manually using the flatbed. The
following documents may be difficult to read properly using the ADF:
• Paper with clips or staples.
• Paper written on with wet ink.
• Paper without a constant thickness. (like envelopes)
• Paper with large rumples or curls. (See the NOTICE on the next page.)
• Paper with folds or tears.
• Tracing paper.
• Coated paper (for example, some paper used for color printing).
• Carbon paper.
• Paper smaller than A8 (Portrait) size, or larger than A3 or Double Letter.
• Materials other than paper (for example, clothes, metal foil, or OHP film).
• Photographic paper.
• Paper with notches on its side.
• Non-rectangular paper.
• Very thin paper.
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
As there is always a slight chance that a document may be damaged when using the ADF, important
original documents should never be fed through the ADF. Instead, read them manually in flatbed
mode.
NOTICES
1. When scanning a translucent document, set the density to light mode.
2. Carbonless papers have a chemical composition that damages the Pad and Pick roller. Therefore, note
the following:
Cleaning:
If mispicks occur frequently, clean the Pad and Pick roller in accordance with
the “Cleaning and Maintenance” manual.
Replacement of parts:
The life of the Pad and Pick roller may be shorter than if PPC paper
documents are fed.
3. The leading edge of all documents fed using the ADF should be straightened so the curl of the paper
meets the specifications shown below:
More than
30 mm
More than
30 mm
Feed direction
Read surface
Less than
3 mm
Feed direction
Read surface
Less than
5 mm
Top of the paper
Top of the paper
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
ADF Document Feeder Capacity
The number of pages that can be loaded into the ADF chute depends on the paper size and the ream
weight. This information is shown in the following graph:
250
250
A4/Letter or smaller
B4
198
200
150
100
50
ADF chute
loading
168
125
153
A3 or 11 x 17"
(number of
pages)
130
98
125
103
78
83
63
0
52
64
81
104
127
ADF Capacity g/m2
Paper weight conversion table
Country
Japan
US
Unit
kg/ream
lb
Conversion
45
13.9
52
55
17
64
64.6
20
77.5
24
90
109.8
34
135
41.8
157
27.9
104
Europe
g/m2
75
90
127
NOTICE
When feeding the document less than 52g/m2 (13.9lb), the number of sheets loaded on the ADF paper
chute must be 100 or less to prevent a paper jam.
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Areas not to be Perforated
Perforations in the shaded areas may cause errors. If you must read data from such a paper, use the
flatbed:
113
79
134
(Unit: mm)
96
Center of
sensor arm
Center of
sensor arm
10
10
10
10
Read reference
position
23 12
Top of paper
15
Front
side
Paper
feeding
direction
Bottom of paper
10
5
10
Center of paper
Areas that must not be perforated
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Grounding Color Areas
The shaded area in the Figure below should have paper grounding color (white) or drop-out color. If not,
turn the white level following Off when reading.
Grounding color (white)
or drop-out color area
Main scanning direction
Read reference
position
3
Subscanning
direction
Read surface
Unit: mm
Grounding color area
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Double Feed Detection Condition
When the double-feed sensor is used, the thickness or the combination of the thickness and the length of
the document is subject to the following specifications:
1 Thickness: 0.065 mm to 0.15 mm
2 Paper length accuracy: 1% or less
3 Any black print at the center of the leading edge of the paper is not allowed. (10 mm x 10 mm)
4 No binding holes are allowed within 35 mm of the middle (halfway point) along the center of the paper.
5 Printing duty: 12 % or less
6 The deviation of the amount of transparent light on the base color area should be less than 10 %.
NOTICE
Certain paper types or a certain condition of paper result in lower detection rates in terms of double feed
detection.
35 mm
10 mm
No printing allowed
Paper feeding
direction
No binding holes allowed
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Job Separation Sheet
1 Shape
The Following shows the typical format of the job separation sheet.
15
Top of paper
15
Reading direction
Bottom of paper
Center of paper
Job separation sheet
2 Paper conditions
The paper conditions are the same as the specification described before. But the paper width must be
A4 or larger (210 mm or larger in width).
4-8
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER
5
SCANNER SPECIFICATIONS
This chapter describes the installation specifications, dimensions,
consumables, and options.
Basic Product Specification
Installation Specification
Dimensions
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Product Specification
o
Item
Specification
Remarks
N .
1
Operating method
Image sensor
Light source
ADF (Duplex), Flatbed
CCD x2
2
Front/Back
3
Inert Gas (Xenon) Lamp x2
Green
4
Minimum
Maximum
A8 (Portrait)
Document
Size
A3/11 x 17 in.
5
6
7
Document Thickness
Optical Resolution
52 g/m2 (14lb) to 127 g/m2 (34lb)
Note *1
400 dpi
Binary
Grayscale
100/150/200/240/300/400/600 dpi
Output
Resolution *5
100/150/200/240/300/400 dpi
100/150/200 dpi
Simplex
Duplex
8
9
Grayscale level (internal)
1024 levels (10bit)
55ppm, 200dpi, A4, Portrait
35ppm, 300dpi, A4, Portrait
45ppm, 300dpi, A4, Landscape
Simplex
Duplex
Scanning
Speed
(Engine Speed)
Note *2
100ipm, 200dpi, A4, Portrait
60ipm, 300dpi, A4, Portrait
80ipm, 300dpi, A4, Landscape
10
11
12
13
Halftone patterns
Capacity of ADF
Compression
Dither/ Error diffusion
250 sheets (A4, 64 g/m2(17lb))
MH/MR/MMR
Note *3
Note *4
High Density
50-pin, Female
SCSI-2
Interface
Note *5
Third Party Slot
Note *6
Notes*1: The details are described in chapter 4.
*2: The actual scanning speed might differ due to host computers’ environment.
*3: The maximum number will differ due to the paper thickness. Refer to chapter 4.
*4: The scanning speed might be slow. The usage with NO COMPRESSION is recommended.
*5: Both SCSI-2 and the Third Party Slot can not be used at the same time.
*6: The Power consumption of the boards should be as follows:
- In the Low Power Mode: Less than 0.35 A
- With IPC-4D option:
- Without IPC-4D option:
Less than 1.5 A
Less than 3.0 A
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Specification
The following table lists the installation specifications of the scanner.
Item
Specification
Depth
Width
Height
Dimensions (mm)
(Without Hopper and Stacker)
696 (27.4")
521 (20.5")
367 (14.5")
Weight (kg)
Voltage
25 (55.2 lb.)
100 to 127 VAC, 200 to 240 VAC 10 %
Single-phase
Input power
Phases
Frequency
50/60 3 Hz
Power consumption
Device status
160 VA or less
Operating
Not operating
-20 to 60˚C
Ambient
condition
5 to 35˚C
(41 to 95˚F)
Temperature
Humidity
(-4 to 140˚F)
20 to 80 %
8 to 95 %
Heat capacity
110 kcal/H (442 BTU/H)
33 (72.7 Ib)
Shipping Weight (kg)
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
(unit: mm)
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER
6
CONSUMABLES AND OPTIONS
This chapter describes the consumables and options.
Consumables
Options
Video Interface Option
IPC-4D Option
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumables
The following table lists consumables used for the scanner. Be sure to keep some consumables in stock.
The customer is responsible for changing these items periodically, in accordance with the guidelines given
below and in the “Cleaning and Maintenance” manual. If they are not changed as recommended, the
scanner may not function properly. The abrasion counter can be used to check the total number of
documents scanned since the last replacement(s).
Name
Pad ASY
Specification
Remarks
Up to 100,000 sheets or one year.
PA03951-0194
Up to 200,000 sheets or one year.
(Two rollers are included.)
Pick rollers
PA03951-0195
NOTICE
Refer to the fi-4750L Image Scanner Cleaning and Maintenance manual for replacing the consumables.
NOTICE
Certain paper types or conditions might reduce the life of consumables.
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Options
The following table lists options available for the scanner.
Name
P/N
Remarks
Video Interface
Board Option
CA02956-2391
Image Processing Circuit
One per unit
IPC-4D
CA02919-0521
Contact your Fujitsu sales agent for more information.
6-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Interface Option
How to Install the Video Interface Option Board
Loosen the two thumb screws to remove
the plate.
1
CAUTION
Turn Off the power before removing the Third Party slot plate.
Insert the board along the rails of the
2
third party slot. Make sure that the
connector is connected securely.
Secure the board with two thumb
screws.
WARNING
Protective measures are required to prevent damage from static electricity.
NOTICE
When the scanner power is turned On again, the scanner automatically recognizes the video interface
board.
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Reading Mode Setting When the Video Interface Option is Installed
This section describes the button specifications and setup details for each of the simplex (front-side),
duplex (front-side) and duplex (back-side) reading modes when the scanner has the video interface option
in the third party slot.
When the reading mode is set by the command from the host computer, the following button operation is
not required.
NOTICE
When the video interface option is installed in the scanner, the scanner automatically recognizes the board
and changes the display.
Whenever you press
, the scanner returns to screen M1.
<Screen M1>
1
Turn the power On and verify that “Scanner
Ready” is displayed on the LCD.
<Screen M2>
2 Press
Screen M2.
then the scanner displays
then the scanner displays
3 Press
Screen 1.
<Screen 1>
<Screen 2>
<Screen 2>
4 Select ADF or FB by pressing
or
then
press . The scanner displays Screen 2.
5 Select “Simplex” or “Duplex” by pressing
or . Then press Enter. The scanner
displays Screen 3.
6 Select “Portrait” or “Landscape” by pressing
or . Then press
. The scanner
displays Screen 4.
<Screen 4>
<Screen 5>
7 Select Size by pressing
or . Then press
. The scanner displays Screen 5.
8 Select Resolution by pressing
or . As
the cursor moves to the left 100/150 may
appear. Then press
displays Screen 6.
. The scanner
6-4
Download from Www.Somanuals.com. All Manuals Search And Download.
<Screen 6>
9 Select Front Density by pressing
or . As
/
the cursor moves to the right,
may appear. Then press
displays Screen 7.
. The scanner
Density display
Without IPC With IPC-4D
Description
option
option
Very dark
Dark
AT1
AT2
* Dynamic Threshold (DTC mode)
* Simplified Dynamic Threshold (IPC mode)
Normal
Light
Very light
* This parameter appears only when IPC-4D is installed.
<Screen 7>
10 Select Back Density (when “Duplex” was
Selected) by pressing
cursor moves to the right,
may appear. Then press
displays Screen 8.
or . As the the
/
. The scanner
<Screen 8>
11 Select Front Halftone by pressing
or
.
Parameter
Description
No
H1
H2
Halftone is Off . Therefore binary reading is specified.
Halftone with dither is specified.
Halftone with error diffusion is specified.
L1
L2
*
*
Automatic separation with dither is specified.
Automatic separation with error diffusion is specified.
* This parameter appears only when the IPC-4D is installed.
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Press
to confirm. The scanner displays
Screen 9.
<Screen 9>
12 Select Back Halftone (when “Duplex” was
specified) by pressing or . The
parameters are the same as in step 11. Press
to confirm. The scanner displays
Screen 10.
<Screen 10>
13 Select Front Document Type by pressing
or
.
Parameter
Description
White level following is ON. Top 3mm part of the document must be left blank
(grounding color is drop-out color). It is useful for reading line arts or texts.
L. (Line)
White level following is Off
It is useful for reading photographs.
P. (Photo)
Press
to confirm. The scanner displays
Screen 11.
<Screen 11>
14 Select Back Document Type (when “Duplex”
was specified) by pressing or . The
parameters are the same as in step 13. Press
to confirm. The scanner displays
Screen 12.
<Screen 12 (Example)>
15 Confirm what you have specified.
If some parameter needs to change, press
or
screen and re-select the parameter by
pressing or and finally press
If all parameters are acceptable, press
to return to the “Scanner Ready” screen.
to select the corresponding
.
Density
Halftone
Line Art or Photo
Resolution
Portrait or Landscape
Paper size
Front side (F) or Back side (B)
Simplex (S) or Duplex (D)
6-6
Download from Www.Somanuals.com. All Manuals Search And Download.
IPC-4D Option
The IPC-4D option performs the image processing.
IPC-4D supports the following image processing.
Item
Description
Pre-Filter
Ball-Point Pen Filter :
Smooth ball point pen strokes.
Background Removal
Dynamic Threshold
Remove background tone and light dither.
One Pass / Two Pass Dynamic Threshold :
Adjust threshold level for binarzing to separate from background.
Captures the light text.
IPC-2 like Dynamic Threshold :
Adjusts the threshold level for binarzing to separate text from
backgrounds, thus capturing light text while preserving its sharpness.
Noise Removal
Auto Separation
2x2 to 5x5 dot removal by matching :
Removes isolated dots in the size of 2x2 to 5x5 pixels.
Auto Separation :
Automatically, detects the text area for binarizing and the photo area for
dithering.
Outline Extract
Filter
Outline
Extract outline of the image
Emphasis (Low/High) :
Emphasis contour.
Smooth:
Smoothing image by averaging.
NOTICE
For the installation and functions of the IPC-4D, refer to the supplied manual.
6-7
Download from Www.Somanuals.com. All Manuals Search And Download.
6-8
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER
7
SETUP MODE
This chapter describes the setup mode of the scanner.
Activating the Setup Mode
Contents of the Setup Mode
Download from Www.Somanuals.com. All Manuals Search And Download.
Activating the Setup Mode
This section describes how to activate the setup mode.
<Screen M1>
1 Turn the power On. Then the scanner
displays “Scanner Ready” on the LCD.
<Screen M2>
<Screen M3>
<Screen M4>
2 If the scanner does not have a video interface
option, go to the procedure step 3. Press
then the scanner with the video
interface option displays Screen M2.
3 Press
Screen M3.
then the scanner displays
4 Press
Screen M4.
then the scanner displays
5 Press
. Now the scanner is at Screen
41 (page 6-3) in Setup mode.
NOTICE
Any time you press
, you can return to the “Scanner Ready” screen.
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents of the Setup Mode
This section describes the contents of the setup mode.
Selectable
parameters
No. Item
Description
Default
Specifies the double feed detection. Double
feed is detected by checking the document
length and/or paper thickness.**
1
2
Double feed check
No
Specifies the document length to enable
double feed detection sets the document
length.
Length check
=No/10/15/20 mm
Tolerance:
No/10/15/20mm
No
Document:
No
Sharpen Darken No
Charactor Copy
Quality
Scanner automatically sets the
recommended reading parameters. 3 sets
of parameters are available when IPC-4D is
not installed.
3
IPC pre-setting
Resetting of
abrasion counter
4
5
Resets the abrasion counter.
-
-
Specifies the time from document Insertion
to the start of picking. User can select the
most comfortable Pick start time for the job.
Pick start time
setting
Time:
0.2 to 29.8 sec
1.0 sec
Specifies the time the scanner waits for the Time:
6
7
8
9
Time-out limit setting next document insertion after the last
document was scanned.
27 values from
1 to 1999 sec
30 sec
Offset:
H:-2 to +3 mm
V:-2 to +3 mm
Offset:
H: 0 mm
V: 0 mm
ADF front offset
setting*
Specifies the horizontal and vertical offset
of the front side image when using the ADF.
Specifies the horizontal and vertical offset
of the back side image when using the
ADF.
Offset:
H:-2 to +3 mm
V:-2 to +3 mm
Offset:
H: 0 mm
V: 0 mm
ADF back offset
setting*
Offset:
H:-2 to +3 mm
V:-2 to +3 mm
Offset:
H: 0 mm
V: 0 mm
Flatbed offset
setting*
Horizontal and vertical offset of the FB
image is specified.
7-2
Download from Www.Somanuals.com. All Manuals Search And Download.
(Continued)
Selectable
parameters
No. Item
Description
Default
The type of IPC option (IPC-4D) is
displayed.
10 IPC status display
11 SCSI ID setting
SCSI ID:
0/1/2/3/4/5/6/7
The SCSI ID is selectable.
5
SCSI terminator
setting
12
Switch the SCSI terminator On/Off.
On/Off
On
Low Power Mode
setting
Change the default setting of the duration
for power save.
5 min.
to 60 min.
13
15 min.
Auto
Select the interface when the scanner has
a board in the third party Slot.
14 Select Interface
Auto/SCSI/Tps
Display TPS Board
ID Number
Display the ID number of the board in the
third party Slot.
15
When the IPC-4D image processing board
is installed in the third party slot, select this
IPC-4D board or the image processing
circuit built in the scanner.
16 IPC mode
Standard/IPC4D Standard
Left/Right:
0 to 15 mm
Top:
0 to 15 mm
Bottom:
Left/Right:
0 mm
Top:
0 mm
Bottom:
0 mm
Adjusts the edge areas to be erased from
the image scanned by the automatic
document feeder (ADF).
17 ADF Edge Erasing
-7 to +7 mm
Left/Right:
0 to 15 mm
Top:
0 to 15 mm
Bottom:
Left/Right:
0 mm
Top:
0 mm
Bottom:
0 mm
Adjusts the edge areas to be erased from
the image scanned by the flat bed (FB).
18 FB Edge Erasing
0 to 15 mm
*
This offset refers to the difference from the value adjusted by automatic offset adjustment.
** Some restrictions apply to the detection of a double feed.
7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Setting double feed detection (Paper Thickness)
When you set the use of double feed detection, you must set it as follows:
<Screen 41>
1 Press
or
and let the scanner
display Screen 41.
2 At Screen 41.
Press either the
(transmitted light).
or
switch to set the double feed detection according to the paper thickness
The paper thickness is checked using the difference between two consecutive sheets of paper fed from
the ADF. On this screen, select whether or not to check for double feeding, and select the error
processing.
Each time either of these switches is pressed, the location of the blinking moves. When the
switch is
pressed, the blinking moves from (1) to (3). When the switch is pressed, the blinking moves in the
opposite direction. However, if the setting by the host computer is valid, the location of the blinking
does not move when either switch is pressed.
(1) “No” is blinking:
Paper thickness is not checked.
(2) “Yes” and “1” are blinking:
Paper thickness is checked. However, a detected double feed
error is displayed on the screen only; processing is continued.
(3) “Yes” and “2: Stop” are blinking: Paper thickness is checked. When the double feed error is
detected, the scan processing is stopped. The error is then
reported to the host.
If you want to disable the double feed, select “No” then press
. Press
to return.
NOTICES
1. Double Feed detection might have better results when both the paper thickness and the paper length
are used.
2. When the document in ADF is not the double fed document, the previous document might be double
fed, in case the scanner stops feeding by using the double feed detection.
3. Depending on the type of printing on the document, a double feed may not be detected by the paper
thickness.
7-4
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Setting double feed detection (Paper Length)
<Screen 42>
1 Press
or
and let the scanner
display Screen 42.
2 Press either the
or
switch to set double feed detection according to paper length. The paper
length is checked using the difference between two consecutive sheets of paper fed from the ADF.
Each time either of these switches is pressed, the location of the blinking moves. When the
switch is
pressed, the blinking moves from (1) to (3). When the switch is pressed, the blinking moves in the
opposite direction. However, if the setting by the host computer is valid, the location of the blinking
does not move when either switch is pressed.
(1) “No” is blinking:
Paper length is not checked.
(2) “Yes” and “1” are blinking:
Paper length is checked. However, a detected double feed error
is displayed only on the screen; processing is continued.
(3) “Yes” and “2: Stop” are blinking: Paper length is checked. When the double feed error is
detected, the scan processing is stopped. The error is then
reported to the host.
If you want to disable the double feed, select “No” then press
. Press
to return.
After pressing
, the scanner displays the screen 42-1.
<Screen 42-1>
3 Press either the
or
switch to set double
feed detection (paper length). When the
switch is pressed, the blinking moves from (1)
to (3). When the
switch is pressed, the
blinking moves in the opposite direction.
(1) The “10” is blinking: Threshold is 10mm
(2) The “15” is blinking: Threshold is 15mm
(3) The “20” is blinking: Threshold is 20mm
7-5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Setting IPC pre-set mode
When you set the use of the IPC pre-set mode, you must set it as follows:
1 Press “Next”
or “Previous”
and let the
scanner display Screen 43.
<Screen 43>
2 At Screen 43, press
or
to select the
pre-Setting and press
to activate the
pre-setting. Then the scanner displays
Screen 43-1.
NOTICES
The following 2PC pre-settings can be selected when 2PC-4D is installed:
Preset 1: Captures texts printed on the colored background
Preset 2: Produces an image with good contrast
Preset 3: OCR Smoothing
Preset 4: Image Smoothing
Preset 5: Dither
The following built-in IPC pre-settings can be selected even though IPC-4D is not installed:
• Sharpen
• Darken Character
• Copy Quality
<Screen 43-1>
3 At Screen 43-1, select “Yes” or “No”. Note
that when you select “Yes”, the IPC setting
from the Host computer is ignored. If you
select “No”, the IPC setting will be changed
according to the host setting. Finally press
.
NOTICE
When you select the Copy Quality, select the scanner and printer settings carefully to get the best quality.
7-6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Reset of the abrasion counter
When you reset the abrasion counter, you must set it as follows:
1 Press “Next”
or “Previous”
and let the
scanner display Screen 44.
<Screen 44>
2 At Screen 44;
If you want to reset the abrasion counter,
select “Yes” through or button and
press . Go to procedure 3.
If you do not want to reset the abrasion
counter, select “No” and press . Finally
press to return.
<Screen 44-1>
3 At Screen 44-1;
If you want to reset the abrasion counter,
select “Yes” and press
want to reset it, select “No” and press
Press to return.
. If you do not
.
5. Setting the pick start time
When you set the pick start time, you must set it as follows:
1 Press “Next”
or “Previous”
and let the
scanner display Screen 45.
<Screen 45>
2 At Screen 45, press
start time or press
to increase the Pick
to decrease the Pick
to activate the
start time. Then press
setting. Finally press
to return.
7-7
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Setting the time-out limit
1 Press “Next”
or “Previous”
and let the
scanner display Screen 46.
<Screen 46>
2 At Screen 46, press
to increase the number
or press
Then press
to decrease the time-out limit.
to activate the setting.
NOTICE
Default is 30 seconds.
3 Press to return.
7. ADF Front Offset Setting
8. ADF Back Offset Setting
9. Flatbed Offset Setting
<Screen 47>
1 Press “Next”
or “Previous”
and let the
scanner display the following:
• Front Offset by ADF : Screen 47.
• Back Offset by ADF : Screen 48.
• Offset of the Flatbed: Screen 49.
<Screen 48>
<Screen 49>
<Screen A>
2 Select “Yes” by pressing the
or
button,
then press
. The scanner displays
Screen A.
7-8
Download from Www.Somanuals.com. All Manuals Search And Download.
<Screen B (Example of ADF Front Offset)>
<Screen B (Example of ADF Back Offset)>
<Screen B (Example of FB Offset)>
3 At Screen A, if you want to let the offset
return to default, select “Yes” otherwise “No”
then press
Screen B.
. The scanner displays
<Screen C (Example of ADF Front Offset)>
4 At Screen B, press
or press to decrease offset.
The increment or decrement is 0.5 mm.
Then press to activate the setting. The
scanner displays Screen C.
to increase the offset
<Screen C (Example of ADF Back Offset)>
<Screen C (Example of FB Offset)>
5 At Screen C, press
to increase the offset
to decrease the offset. Then
to activate the setting. The
or press
press
scanner displays the next item of the setup
mode.
7-9
Download from Www.Somanuals.com. All Manuals Search And Download.
10.IPC Status Display
<Screen 50> (An example)
<Screen 50-1>
1 Press “Next”
or “Previous”
and let the
scanner display Screen 50.
2 Screen 50 displays the IPC option installed
and the total image memory installed.
3 Press
to return.
11.SCSI ID Setting
<Screen 51>
1 Press “Next”
or “Previous”
and let the
scanner display Screen 51.
2 At Screen 51, press
or
to select SCSI
ID. Then press
to activate the setting.
3 Press
to return.
12.SCSI Terminator Setting
<Screen 52>
1 Press “Next”
or “Previous”
and let the
scanner display Screen 52.
2 At Screen 52, press
Terminator. Then press
setting.
or
to select
to activate the
3 Press
to return.
7-10
Download from Www.Somanuals.com. All Manuals Search And Download.
13.Low Power Mode Setting
<Screen 53>
1 Press “Next”
or “Previous”
and let the
scanner display Screen 53.
<Screen 53-1>
2 Pressing the
and press
or
button, select “Yes”
. The Scanner displays
Screen 53-1.
3 At Screen 53-1, press
or
to select the
time duration. A minimum of 5 min to the
maximum of 60 minutes can be selected.
Then press
to activate the setting.
NOTICE
1. At Screen 53, “No” does not mean that you can turn off the “Low Power Mode” (Power Save Mode).
You cannot disable the Power Save Mode.
®
2. The default time recommended by the ENERGYSTAR program is 15 minutes. The default for the
M4097D scanner is 15 minutes, as recommended.
4 Press
to return.
7-11
Download from Www.Somanuals.com. All Manuals Search And Download.
14.Select Interface
<Screen 54>
1 Press “Next”
or “Previous”
and let the
scanner display Screen 54.
NOTICE
The screen 54 will appear oniy when the scanner has proper interface boards or option boards in the third
party slot.
2 At Screen 54, press
interface type. Press
change the setting.
or
to select the
if you want to
NOTICES
1. Normally, this setting does not have to be changed.
2. When an appropriate board is installed in the third party slot of the scanner, the scanner automatically
turns off the SCSI interface, activating the board in the third party slot. Screen 54 can be used to
forcibly change the selected interface. The selected interface is then forcibly changed.
3. The SCSI interface and the board installed in the third party slot cannot be used at the same time.
4. The default is Auto.
3 Press
to return.
7-12
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Display the TPS Board ID Number
<Screen 55> (An Example)
1 Press “Next”
or “Previous”
and let the
scanner display Screen 55.
The scanner displays the ID number if the
applicable board is installed.
NOTICE
If the Fujitsu video Interface Option board is installed properly, the display shows “ID=7”.
2 Press
to return.
16. Select Built-In/IPC-4D Image Processing
1 Press ”Next” or and let the scanner
<Screen 56>
display the Screen 56.
2 At Screen 56, press
”Standard” or ”IPC-40”.
or
to select
When ”Standard” is selected, the scanner uses
its built-in image processing. On the other hand,
the scanner selects the image processing of the
IPC-4D when the ”IPC-4D” is installed and
selected.
NOTICE
The factory default is ”Standard”.
NOTICE
fi-4750L has built-in Image Processing. The following image processing is supported both by the fi-4750L
and the IPC-4D. As a default, the scanner built-in functions are enabled. By setting "On" using the
Operator Panel, the IPC-4D image processing overrides the built-in functions.
Image Processing
IPC-4D
5 x 5 matrix
M4097D
1 Emphasis/Smoothing
2 Outline
3 x 3 matrix
Laplacian
Pre-threshold Laplacian
IPC-2 like SDTC
3 Simplified Dynamic Threshold
3 x 3 max-min
The IPC-4D support of those functions is intended for compatibility with the IPC-3/3D. The matrix size
used in the IPC-4D is larger than the one in the fi-4750L. The fi-4750L Built-in Dynamic Threshold is a new
algorithm.
7-13
Download from Www.Somanuals.com. All Manuals Search And Download.
17. Adjust ADF Erasing Edges
<Screen 57>
1 Press “Next”
or “Previous”
and let
the scanner display Screen 57.
2 At Screen 57, press
“Yes” and press
or
to select
. Then the scanner
displays Screen 57-1.
<Screen 57-1>
<Screen 57-2>
<Screen 57-3>
3 At Screen 57-1, select “Yes” to return the
settings to the factory default or select
“No” to make new settings (as shown
below). Then press
displays Screen 57-2.
. The scanner
4 At Screen 57-2, press
or
to change
the top setting. The value changes in 1
mm units. Then press to activate
the setting. The scanner displays Screen
57-3.
5 At Screen 57-3, press
or
to change
the bottom setting. With (+:Up), the area
is set upward from the bottom edge of the
image. With (–:Down), the area is set
downward from the bottom edge of the
image. The value changes in 1 mm units.
Then press
to activate the setting.
The scanner displays Screen 57-4.
<Screen 57-4>
<Screen 57-5>
6 At Screen 57-4, press
the left setting. The value changes in 1
mm units. Then press to activate
or
to change
the setting. The scanner displays Screen
57-5.
7 At Screen 57-5, press
the top setting. The value changes in 1
mm units. Then press to activate
or
to change
the setting. The scanner displays the
next setup item.
7-14
Download from Www.Somanuals.com. All Manuals Search And Download.
18. Adjust FB Erasing Edges
<Screen 58>
1 Press “Next”
or “Previous”
and let the
scanner display Screen 58.
2 At Screen 58, press
or
to select “Yes”
and press
. Then the scanner displays
Screen 58-1.
<Screen 58-1>
3 At Screen 58-1, select “Yes” to return the
settings to the factory default or select “No” to
make new settings (as shown below). Then
press
58-2.
. The scanner displays Screen
<Screen 58-2>
<Screen 58-3>
4 At Screen 58-2, press
top setting. The value changes in 1 mm
units. Then press to activate the
setting. The scanner displays Screen 58-3.
or
to change the
5 At Screen 58-3, press
or
to change the
bottom setting. With (+:Up), the area is set
upward from the bottom edge of the image.
With (–:Down), the area is set downward
from the bottom edge of the image. The
value changes in 1 mm units. Then press
to activate the setting. The scanner
displays Screen 58-4.
<Screen 58-4>
<Screen 58-5>
6 At Screen 58-4, press
left setting. The value changes in 1 mm
units. Then press to activate the
setting. The scanner displays Screen 58-5.
or
to change the
7 At Screen 58-5, press
top setting. The value changes in 1 mm
units. Then press to activate the
or
to change the
setting. The scanner displays the next setup
item.
7-15
Download from Www.Somanuals.com. All Manuals Search And Download.
7-16
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY OFTERMS
A4 size
A standard paper size. Paper size is 210 x 297 mm.
A5 size
A standard paper size. Paper size is 148 x 210 mm.
A6 size
A standard paper size. Paper size is 105 x 148 mm.
A7 size
A standard paper size. Paper size is 74 x 105 mm.
A8 size
A standard paper size. Paper size is 53 x 74 mm.
Abrasion counter
Counts the cumulative number of documents read to indicate when belts/rollers should be replaced. The
number of read documents accumulates until an operator resets the counter. The counter should be reset
when these consumables are replaced.
ASCII
The acronym for American Standard Code for Information Interchange.
ASCII is a set of 256 codes (numbered 0 to 255) used to communicate information between a computer and
another device such as a scanner.
Automatic separation
An image processing method in which the scanner automatically detects difference between text and photos,
andchoosesthethresholdaccordingly. Automaticseparationallowsthescannertoswitchbetweenlinemode
and half tone mode in one pass.
Automatic start mode (<-> manual start mode)
In this mode, the reading operation is activated only by issuing the the START command.
Backside reading = Back-side scanning
Refers to reading the backside of the document, specifically in Duplex reading mode.
Bit
The smallest unit of information in computer memory. A bit is a single digit, either a 1 or a 0, in the binary
numbering system. Eight bits equal one byte.
Density
In this manual, refers to a measurement of the depth of the display.
Dither
Technique for producing halftone images by representing the entire grayscale with only two pixel levels, black
and white.
GL-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Double feed detection
A scanner function which detects the accidental feeding of multiple sheets by the ADF unit. Can be turned on
or off by the operator.
Double Letter Size
A standard paper size used in the U.S.A. and othe countries. Paper size is 11 x 17 inches.
dpi
Dots per inch.
Dropout color
A color which is used in the document but does not appear in the read image.
Duplex reading mode
A reading mode in which both sides of the document are read.
Equipment Error
An error that cannot be corrected by the operator. Call CE.
Error diffusion
High-quality halftone (pseudo-grayscale) image production based on black-and-white pixel binarization. A
pixel’s optical density and that of adjacent pixels are summed, with black pixels relocated in their order of
density as they relate to adjacent pixels.
The purpose of this technique is to minimize the average error between read and printed densities. Density
data for adjacent pixels is modified by diffusing errors on the objective pixel into several pixels, which are then
binarized. Thismaintainshighgrayscalelevelsandresolutionduringreading,whilesuppressingmorepatterns
by dotted halftone images such as newspaper photographs.
FB
In this manual, FB means flat bed.
Filtering
A correction method that improves the read quality of handwritten documents. The read quality of images
writteninpencilorball-pointedpendependsonthereflectivelightcharacteristicsofthespecificinkorleadused.
Dropped pixels may produce outlines, gaps, or thin, barely connected lines due to uneven optical density.
Filtering detects areas lighter than their surroundings and increases their density to improve image clarity.
Front-side reading = Front-side scanning
Refers to reading the front side of the document, specifically in Duplex reading mode.
Halftone processing
Any method used to reproduce a photograph which includes a shade as an image composed of dots, namely,
a binary image. Dithering and error diffusion processing are examples of halftone processing.
GL-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Hexadecimal
A base-16 numbering system (also commonly referred to as hex numbers). Since a base-16 system requires
16 digits, numbers 0 through 9 and letters A through F are used. It is convenient to express binary numbers
in hexadecimal because fewer digits are required.
Image emphasis
Density is decreased for lighter but not completely white areas adjacent to black areas. Weakening this
emphasis eliminates spot noise or produces softened images.
Image processing
An image is read with specified parameters.
Interface
Theconnectionthatallowscommunicationfromonepartofasystemtoanother. Forexample,electricalsignals
are transferred between the computer and scanner over an interface cable.
Inversion (Reverse-image reading)
In reverse-image reading, data is changed from black to white and vice versa.
IPC preset mode
While reading binary images, it is necessary to set the scanner according to the quality of the sheet to be read.
In this mode, these settings can be performed in advance by corresponding each setting to a pattern number.
IPC-4D
Image processing option of this scanner.
IRAS
Initialization of the hardware.
Landscape orientation
A document is transported and read with the long side vertical to the moving direction.
Letter size
A standard paper size used in the U.S.A. and other countries. Paper size is 8-1/2 x 11 inches.
Linedrawing mode
Selecting linedrawing mode makes threshold and contrast settings effective but prevents brightness from
being set. The specified threshold value determines whether black or white pixels are scanned. Line drawing
mode is therefore appropriate for scanning text and line art images.
Manual Feed mode = Manual Mode
Requires the operator to feed each document manually into the ADF paper chute.
Manual start mode (<-> automatic start mode)
ThereadingoperationisactivatedbypressingtheSTARTbuttoninthismode.Availableonlywhenvideooption
board is installed.
GL-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Mirror image
Thereadimageissymmetricallyflippedtoproduceamirrorimageoftheoriginaldetectedinthemainscanning
direction.
Noise removal
Isolated noise from an image appearing as black spots in white areas and voids in black areas is removed to
improve image quality.
Operator panel
A panel containing the scanner indicators and buttons. The operator panel is used to control scanner
operations such as loading document, selecting features, and changing setup options.
Outline extraction
The boundary between black and white areas is traced and the outline extracted for closed areas.
PAPER JAM
A warning informing the user that document is jammed in the transport unit, or that transportation is disabled
because the transport unit is slippery. This warning also appears when a double feed is detected.
Photograph mode (White level follower OFF)
Selecting photograph mode makes brightness and contrast settings effective but prevents the threshold from
being set. With photograph mode, the darkness of image corresponds to the black-pixel density, making it
suitable in scanning images such as photographs having gradations.
Photo mode = photograph mode
A photograph is read properly in this mode.
Pick start time
Theperiodfromthemanualinsertionofthedocumentuntilpickingstartsafterthedocumentpassesthehopper
empty sensor.
Portrait orientation
A document is transported and read with the long side parallel to the moving direction.
Paper counter
Indicates the total number of read document from start of reading until the hopper becomes empty.
Read operation
Refers to the reading operation including Simplex reading and Duplex reading.
RS-232C interface
A type of serial interface. See Serial interface.
SCSI-ID
Used to specify a particular SCSI device when the initiator selects a target or the target reconnects to the
initiator.
GL-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial interface
A standard computer interface. Information is transferred between devices over a single wire (although other
wires are used for control).
With a serial interface, an interface cable greater than 3 meters (10 feet) can be used. This is often necessary
in networking environments, where the scanner may be shared.
SETUP mode
In this mode, users can view or set a variety of function in off-line.
Simplex reading mode
Onlythefrontsideofthedocumentisreadinthismode.Placethedocumentsfaceupatthecenterofthehopper
table.
Smoothing
Aprocessthateliminates“jaggies”fromslantedlinesandcurves.Irregularconvexitiesaredeletedandirregular
concavities filled in. This is useful in OCR applications, for example.
Temporary Error
An error correctable by the operator.
Terminator
Devices with a SCSI interface can be daisy-chained. A resistor that includes terminal circuits needs to be
placedatbothendsofacablewhendevicesaredaisy-chained.Ifadevice(suchasascanner)isthelastdevice
in a chain, leaving an interface connector unused, a Terminator theerfore must be attached to provide those
terminal circits.
Third Party Interface
Optional board provided by Fujitsu or interface board provided by a third party can be installed and used.
Time-out limit
This is the time the scanner waits for next document insertion after the last document feeding. The scanner
returns Paper Empty when no document is set after time-out limit.
TPS
Third Party Slot.
GL-5
Download from Www.Somanuals.com. All Manuals Search And Download.
GL-6
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
Abrasion counter 1-7
Activating the Setup mode 7-1
ADF 1-2, 1-3
A
FB erasing edges 7-3, 7-15
Feeding direction 4-1
F
ADF
document feeder capacity 4-4
erasing edges 7-3, 7-14
lever 1-2, 1-3
Gate assembly 1-4
Grounding color areas 4-6
Guide A assembly 1-4
G
mode 1-9
paper chute 1-2
Alarm 1-10
Ambient condition 5-2
Arrangement 1-5
Assemblies 1-4
Halftone processing 6-5
Heat capacity 5-2
Hopper empty 1-9
H
I
Image processing circuit 7-3, 7-13
IMP connector 1-2, 1-3
Input power 5-2
Button
B
C
/LED Function 1-6
Inspection 2-2
Installation specifications 5-2
INT connector 1-2, 1-3
Interface connectors 1-2, 1-3
Interface select 7-3, 7-12
IPC
Cable connection 2-4
Check LED 1-6
Checking the components 1-1
Chute cable 1-1
Chute roller 1-1, 1-4
Connecting
the chute cable 2-6
the interface cable 2-5
the power cable 2-4
Consumables 6-1
Contents of the Setup mode 7-2
Conventions vi
Counter display 1-7
mode select 7-3, 7-13
preset mode setting 7-2, 7-6
status display 7-3, 7-10
IPC-4D option 6-2, 6-7, 7-13
Job separation sheet 4-8
J
L
Label
A
B
2-2
2-2
Density 6-5
D
Dimentions 5-2, 5-3
Document
Landscape orientation 6-4
LCD 1-5
bed 1-2, 1-3
LED 1-6
cover 1-2, 1-3
holding pad 1-2, 1-3
Quality 4-2
Loading documents
ADF 3-4
Flatbed 3-8
Size 4-1
type 3-5, 4-2
Double
Low power mode
setting 7-3, 7-11
waking up from 3-2
feed detection condition 4-7
feed detection setting 7-2, 7-4, 7-5
feed error 1-9
Manual
M
Duplex reading mode 6-4
feed mode 3-3
start mode 1-6
Manual and driver 1-1
Enter button 1-6
Exit button 1-6
E
EXT connector 1-2
IN-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Next button 1-6
Note, Liability iv
0ffset 7-8
N
O
pick start time 7-7
SCSI ID 2-7, 7-10
SCSI terminator 2-7, 7-10
time-out limit 7-8
Setup mode 7-1, 7-2
Shipping lock 2-3
Simplex 6-4
Offset setting 7-2, 7-8
Operation status 1-8
Operator panel 1-2, 1-5
Option 6-2, 6-3, 6-7
Size 6-4
Pad Assembly 1-1, 1-4, 6-1
Paper
Specifications 5-1, 5-2
Stacker 1-2, 1-4, 2-6
Start button 1-5, 1-6
Stop button 1-5, 1-6
P
counter 1-7
weight 4-2
Paper weight 3-6
Paper weight roller 1-2,1-3
Perforation areas 4-5
Pick
Temporary error 1-9
Third party slot 1-2, 1-3
Time-out limit setting 7-2, 7-8
TPS board ID number display 7-3, 7-13
Turning
T
roller 1-4, 6-1
start time setting 7-2, 7-7
Plain paper 4-2
Portrait 6-4
the power on 3-1
the power off 2-4
Power
cable 1-1, 2-4
consumption 5-2
inlet 1-2, 1-3, 2-4
switch 1-2, 1-3, 2-4, 3-1
Precautions 2-1, 4-2
Units 1-2
Units and Assemblies 1-2
U
Video interface board option 6-2, 6-3
Weight 5-2
V
Preface
v
Previous button 1-6
W
Read LED 1-6
Reading
R
S
(Left Arrow Key) button 1-6
(Right Arrow Key) button 1-6
(Next) button 1-6
mode 6-4
face 6-4
thick book 3-9
Resetting abrasion counter 7-2, 7-7
Resolution 6-4
Roller cover 1-4
(Previous) button 1-6
(Send To) button 1-6
(Start) button 1-6
(Stop) button 1-6
(Enter) button 1-6
(Exit) button 1-6
Scanner 1-1
SCSI ID setting 7-3, 7-10
SCSI terminator setting 7-3, 7-10
Select
interface 7-3, 7-12
IPC mode 7-3, 7-13
Setting
double feed detection
paper thickness 7-4
paper length 7-5
IPC preset mode 7-6
low power mode 7-11
IN-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Declarations of Conformity
DE-1
Download from Www.Somanuals.com. All Manuals Search And Download.
DE-2
Download from Www.Somanuals.com. All Manuals Search And Download.
|
FEIN Power Tools Welder FSC 16 User Manual
Flymo Trimmer MCT250 User Manual
Franke Consumer Products Ventilation Hood FKU 368 TC W User Manual
Frigidaire Microwave Oven FPMV189K User Manual
Fujitsu Air Conditioner AOU18CXQ User Manual
Gaggia Espresso Maker SUP027YDR User Manual
Garmin Marine GPS System 4008 User Manual
GE Monogram Ventilation Hood ZXR8510 User Manual
Genius Speaker 31730952100 User Manual
GE Universal Remote RM94948 User Manual