Fujitsu Camcorder MCE3064SS User Manual

OPERATOR PANEL  
TTL-IC  
This guide is prepared to instruct the user on the switch and jumper  
settings in the MCE3064SS/MCF3064SS/MCE3130SS when you install  
your MCE3064SS/MCF3064SS/MCE3130SS.  
CNH2 (EXTERNAL SWITCH  
SETTING)  
1
2
Note; Factory default settings are marked with .  
3
Pin#  
Function  
Cartridge-in detection  
SCSI ID 4  
Open  
Short  
4
1
2
3
4
5
6
7
8
9
Layout of PCA  
SCSI ID Setting  
Table 1  
SW1-01 SW1-02 SW1-03  
5
SCSI ID  
6
LED source (+5 V)  
SCSI ID2  
0
1
2
3
4
5
6
7
Off  
Off  
Off  
Off  
On  
On  
On  
On  
Off  
Off  
On  
On  
Off  
Off  
On  
On  
Off  
On  
Off  
On  
Off  
On  
Off  
On  
MCE3064SS, MCF3064SS,  
MCE3130SS  
Magneto-Optical Disk Drives  
7
LED source (–)  
SCSI ID1  
8
9
Signal to eject cartridge  
Ground  
10  
11  
12  
13  
14  
15  
16  
Device type mode  
Fixed disk  
Disabled  
Enabled  
MO  
10 SCAM mode  
Enabled  
Disabled  
11 Write verify mode  
12 Ground  
Installation Guide  
Installationsanleitung  
Guide d'installation  
13 Macintosh mode  
14 SCSI type 0  
Disabled  
SCSI 2  
Disabled  
Enabled  
SCSI 1  
Enabled  
SW1 AND CNH2 SETTINGS  
Switch 1 sets the SCSI ID and some drive functions and CNH2 sets  
additional drive functions.  
15 Terminating resister mode  
16 Ground  
0V  
SW1  
Key#  
Note: The cable length must not exceed 30cm.  
Function  
Key on  
Key off  
01  
02  
03  
04  
05  
06  
07  
08  
Device Driver  
————  
————  
SCSI ID (see table 1 above)  
You need to install Fujitsu's device driver to avoid the 2KB sector  
problem in Windows9x and the OS-timeout-problem in Windows9x and  
NT3.51/4.0.  
SCSI data bus parity check  
Write cache mode  
Device type mode  
Spindle automatic stop mode  
Factory test (Not to be set by user)  
Enabled  
Enabled  
MO  
Enabled  
Enabled  
Disabled  
Disabled  
Fixed Disk  
Disabled  
Disabled  
MCE3064SS/MCF3064SS/MCE3130SS HANDLING AND MAINTENANCE  
Orientation  
Cleaning lens and media  
The drive can be installed in one  
of three orientations; either PCA  
up or on either side edge.  
recommendation  
Clean the lens on the drive head  
and the disk media once every  
three months. More frequent  
cleaning may be required in a  
dirty environment. Use the  
Fujitsu head cleaning kit and  
media cleaning kit. Head  
cleaning kits from other vendors  
will not work.  
CNH1 (TERMINATING POWER AND SCSI TERMINATION)  
Terminal CNH1 uses shorting bars to set the power source and to  
enable or disable SCSI termination.  
Ejecting cartridge  
Cartridges can be ejected by  
pressing the eject key or by a  
SCSI eject command. Never  
eject a cartridge mechanically  
except in an emergency.  
Pin# Function  
Short  
Open  
Power supplied by 1–2 3–4  
1–2 Power supplied by Supplied Not  
Drive  
Short Open  
Open Short  
Short Short  
drive  
supplied  
Host controller  
3–4 Power supplied by Supplied Not  
Drive and Host  
controller  
host controller  
supplied  
WORLD WIDE WEB SITE  
5–6 SCSI termination Enabled Disabled  
enabled  
USA  
CANADA  
COPYRIGHT FUJITSU LIMITED  
SEPT. 1999  
C156-E117-02XA  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Estate Refrigerator LT14EK User Manual
Extron electronic Car Amplifier DP DA2 User Manual
Extron electronic Home Theater System MP 101 User Manual
Fisher Price Baby Toy H7338 User Manual
FujiFilm Camcorder 16082969 User Manual
GarrettCom Switch MAGNUM 6KM User Manual
GE Clothes Dryer GFDS355 User Manual
Generac Power Systems Portable Generator 005040 2 User Manual
Genesis Advanced Technologies Speaker Gen 928 User Manual
Goodman Mfg Air Conditioner 15 TON COMMERCIAL PKG AC User Manual