L3891
IMPORTANT!
KEEP INSTRUCTIONS
FOR FUTUREREFERENCE.
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Pad
Seat Back
ꢀ Frames
Seat Bottom
Back Base
Hinge Rod
Front Base
ꢀ Seat Bottom Tubes
Footrest
Food Tray
Base Tray
Teether Toy
Note: Tighten or loosen all screws with a Phillips screwdriver.
Do not over-tighten the screws.
#10 x ꢀ,ꢀ cm Black Screws - 7
#8 x 1,9 cm Screws - 8
Shown Actual Size
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
IMPORTANT! Before assembly and each use, inspect this
product for damaged hardware, loose joints, missing parts or
sharp edges. DO NOT use if any parts are missing or broken.
Contact Mattel for replacement parts and instructions if
needed. Never substitute parts.
Footrest
Seat Bottom
1
•Place the seat bottom face down on a flat surface.
•At an angle, fit the footrest to the seat bottom, as shown.
Plastic Rings
3
•Align the holes in the plastic rings and the seat bottom tubes.
Seat Bottom Tubes
•Insert a #8 x 1,9 cm screw through each plastic ring and into
the seat bottom tubes, as shown.Tighten the screws.This may
require extra force.
•Push the seat bottom tubes back and forth to be sure they
are secured to the seat bottom. If the seat bottom tubes
move, you have probably not fastened them properly. Remove
the screws and check to be sure the screw holes in the
seat bottom tubes and seat bottom plastic rings are aligned.
Replace and tighten the screws.
ꢀ
Plastic Rings
•Slide a seat bottom tube through each set of plastic rings
on the seat bottom.
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Insert Screws Here
Hinge
Hinge Rod
ꢁ
6
•Insert two #10 x 2,2 cm black screws through the
footrest and into the seat bottom.Tighten the screws.
•Turn the seat assembly face down.
•Insert the hinge rod through the hinge on the seat back
and seat bottom, as shown.
•Insert a #10 x 2,2 cm black screw into the hinge rod.
Tighten the screw.
•Set the seat assembly aside for Assembly step 10.
Seat Back Pins
Frame Leg
Slot
Slot
7
ꢂ
•Pull the frame leg out on each frame to open. Make sure it
"clicks" into place.
•Turn the seat bottom assembly upright.
•Fit the seat back pins into the slots in the top side of the
seat bottom assembly.
ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Frame Decorated Side
4
Seat Height Adjusters
Frame Back Legs
Position ꢁ
Press Lever
Back Base
9
Screw Retainers
•While pressing the levers on the seat height adjusters,
lift them to position 4 on the frame front legs, as shown.
Seat Assembly
8
•Position a frame so that the
decorated side is outward.
•Insert the back frame legs into the back base.
•Fit a screw retainer over a hole in the back base, as shown.
•Insert a #10 x 2,2 cm black screw through the screw
retainer and back base. Tighten the screw.
Sockets
•Repeat this procedure to fasten the other frame back leg to
the other side of the back base.
Hint: The #10 x 2,2 cm black screws may have been
assembled to the screw retainers.
10
Seat Bottom Tubes
•Fit the seat assembly between the two frames.
•Insert the seat bottom tubes into the sockets in each seat
height adjuster.
Hints:
•Be sure the seat height adjusters are in the same position
(position 4).
•You may need to push the frames apart slightly to fit the
seat bottom tubes into the seat height adjuster sockets.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Seat Height Adjusters
Screw Retainers
Front Base
Seat Bottom Tube Ends
11
13
•Fit the frame front legs onto the front base.
•Fit a screw retainer over the hole in a front leg.
•Insert a #10 x 2,2 cm black screw through the screw
•From the back and bottom of the assembly,insert a #8 x 1,9 cm
screw through both seat height adjusters and the ends of
the seat bottom tube.Tighten the screws.This may require
extra force.
retainer and front leg.Tighten the screw.
•Repeat this procedure to fasten the other end of the front
base with the remaining screw retainer and
#10 x 2,2 cm black screw.
Hint: The #10 x 2,2 cm black screws may have been
assembled to the screw retainers.
PRESS
PRESS
PuSH
PuSH
1ꢁ
•Squeeze the restraint release tabs together.
•Remove the ends of the restraint system from the peg.
1ꢀ
•Push each seat height adjuster to be sure they are
completely on the seat bottom tubes.
•Insert a #8 x 1,9 cm screw through each seat height
adjuster and the ends of the seat bottom tube.Tighten
the screws.This may require extra force.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Shoulder Straps
Crotch Strap
16
1ꢂ
•Fit the pocket on the top of the pad onto the seat back.
•Remove both shoulder straps from the seat back.
•Remove the crotch strap from the seat back.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Shoulder
Straps up
Clips
Lowest Slot
Crotch
Strap Down
17
19
•Fit the clips on the front edge of the pad onto the
seat bottom.
Hint: Do not unbuckle the restraint system.It is easier to
attach or re-attach it to the product if it is buckled.
•Grasp the restraint system so that the shoulder straps are up
and the crotch strap is down.
•Insert the end of the crotch strap through the lowest slot
in the pad and the seat back.
•From behind the product, attach the end of the crotch strap
to the peg.
18
•Hook the elastic loops on each side of the pad onto the
tabs in the seat back.
ꢀ0
•From behind the product, attach the end of the crotch
strap to the peg.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
ꢀ1
ꢀꢀ
Smaller Baby
•Insert the ends of
the shoulder straps
through the lower slots in the pad.
•From behind the product, attach the ends of the shoulder
straps to the peg.
Larger Baby
•From the front of
the product, insert
the ends of the shoulder
straps through the upper slots in the pad and seat back.
•From behind the product, attach the ends of the shoulder
straps to the peg.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure Child
Adjuster
WARNING
Prevent serious injury or death from falls
or sliding out: Always use the restraint
system for the upright and reclined positions
of the seat. Adjust restraint to fit your child
snugly. The tray is not designed to hold the
child in the chair.
Shoulder Strap
Free End
Anchored End
Waist/Shoulder Belt
Waist/Shoulder Belt
TIGHTEN
ꢀ
•To tighten the waist straps: Feed the anchored end of
the waist strap up through the buckle to form a loop .
Pull the free end of the waist strap .
•To tighten the shoulder straps: Hold the adjuster and
pull the shoulder strap down C.
Adjuster
Shoulder Strap
Crotch Belt
Free End
1
•Place your child in the seat. Position the crotch belt
between your child’s legs.
•Fasten both waist/shoulder belts to each side of the
crotch belt. Make sure you hear a "click" on both sides.
Anchored End
•Check to be sure the restraint system is securely attached
by pulling it away from your child.The restraint system
should remain attached.
LOOSEN
3
•To loosen the waist straps: Feed the free end of the waist
strap up through the buckle to form a loop . Enlarge the
loop by pulling on the end of the loop toward the buckle.
Pull the anchored end of the waist strap to shorten the free
end of the waist strap .
•To loosen the shoulder straps: Lift the adjuster C.
Note: After adjusting the restraint system to fit your child,
make sure you pull on it to be sure it is securely fastened.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure Child
Shoulder Straps
Shoulder Straps
ꢂ
•You can remove the
shoulder straps and
use only the waist
restraint.
PuSH
PuSH
•From behind the
product, squeeze the
restraint release tabs
and remove the
PuSH
PuSH
ꢁ
shoulder straps.
•From the front of
the product, pull to
remove the shoulder
straps from the seat
back/pad.
•Push to remove the
shoulder straps from the waist restraint buckle slots.
•Store the shoulder straps in a safe in a safe place for future use.
To change strap slots:
•From behind the
product, squeeze the
restraint release tabs
and remove the
shoulder straps.
•From the front of the
high chair, pull the shoulder portions of the restraint
system out and then fit them back through the desired
shoulder strap slots in the seat pad and in the seat back.
•From behind the product, attach the ends of the shoulder
straps to the peg.
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
using the Trays
WARNING
Prevent serious injury or death from falls
or sliding out: Always use the restraint
system for the upright and reclined
positions of the seat. Adjust restraint to
fit your child snugly. The tray is not
designed to hold the child in the chair.
PuLL
PuLL
PuSH
7
•You can adjust the base tray forward or backward.
- While pulling the latches underneath the tray out,
adjust the base tray forward or backward .
Tray
- While pushing the release bar on the front of the base
tray, adjust the base tray forward or backward .
Latch
Armrest
PuLL
PuLL
6
PuSH
•While pulling the latches underneath the tray out, slide it
onto the armrests. Release the latches to secure the tray
in place.
8
Hint: Before use, thorougly wash all parts (the trays) that
•To remove the tray:
may contact food.The base tray is not dishwasher safe.
- Pull one or both of the latches underneath the tray out
and lift .
- Push the release bar on the front of the tray and lift .
13
Download from Www.Somanuals.com. All Manuals Search And Download.
using the Trays
using the Brakes
WARNING
Food Tray
Base Tray
Prevent serious injury or death from falls
or sliding out:
• Position the high chair away from steps,
hot surfaces, electrical cords and other
items that may cause injury to the child.
• Always leave wheels locked.
9
•Fit the food tray into the base tray, as shown.
Hint: Before use, thorougly wash all parts (the
trays) that may contact food.The food tray is not
microwave safe.
Toy
Lift Tab
Press Tab
11
To Lock: Press the tab on all four wheels down until you
hear a "snap".
To Unlock: Lift the tab on all four wheels up.
10
Press
•Insert and “snap” the toy tab into either slot in the tray.
Hint: To remove the toy, press the tab and lift the toy.
1ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Seat
WARNING
Prevent serious injury or death from falls
or sliding out:
• Always use the restraint system for the
upright and reclined positions of the seat.
Adjust restraint to fit your child snugly.
The tray is not designed to hold the child
in the chair.
Seat Height Adjuster
Press Lever
• It is recommended that only children
capable of sitting upright unassisted use
the upright position of the high chair.
4
upright
13
Semi-Recline
Hint: Adjust the seat height to any of seven positions!
To adjust the seat height:
•Press the levers on both seat height adjusters and lift or
lower the seat to the desired height.
•Make sure both sides of the seat are adjusted to the same
height. Push the seat bottom to be sure the seat is locked
in place.
Recline
LIFT
1ꢀ
BACK VIEW
Hint: Adjust the seat angle to any of three positions:
Upright, Semi-Recline or Recline.
To adjust the seat angle:
•Squeeze the seat back handle and push the seat back
forward or, pull it backwards to the desired position.
•Push the seat back to be sure it is latched in position.
1ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Storage
Care
•The pad, frame, and base tray may be wiped clean using
a mild cleaning solution and a damp cloth. Do not
use bleach.
•The restraint system may be wiped clean or is machine
washable. Machine wash in cold water on the gentle
cycle. Do not use bleach. Line dry.
•The food tray, teether toy and restraint system are also top
rack dishwasher safe (or use bottom rack - without using
the drying cycle).
Pull Frame
Release Latch
To remove the pad:
•Remove the elastic loops from the pegs on the underside
and back of the seat.
•From behind the product, squeeze the restraint release
tabs and remove the restraint system from the peg.
•From the front of the product, pull to remove the
restraint system.
•Unfasten the pad hooks from the front edge of the seat.
Lift the top of the pad off of the seat back.
•To replace the pad, refer to Assembly steps 14-20.
IMPORTANT! Never use this product without the
restraint system. Replace the waist/shoulder belts and
crotch belt.
1ꢁ
•With the legs all the way open, lower the seat to position 7
the lowest position).
•Pull the frame release latches forward and push the rear legs
toward the front legs.
©2006 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.
PRINTED IN CHINA
L3891pr-0729
Download from Www.Somanuals.com. All Manuals Search And Download.
|