™
Deluxe Healthy Care
High Chair
Product features and decoration may vary from the photo above.
Model Number: B2105, B0326
Please keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required.
Tool needed for assembly: Phillips Screwdriver (not included).
Disc
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Headrest
3 Food Trays
Pad
Seat Back
Base Tray
Seat
Bottom
Frame
#10 x 7/8"
Black Screw
Hinge
Rod
Storage
Caddy
#8 x 3/4" Screws
2 Seat Bottom Tubes
4 Screw Retainers
#8 x 3/4"
Screws
#10 x 7/8"
Black Screw - 4
#8 x 3/4" Screws
Frame
Back Base
Footrest
4 Wheels
#10 x 7/8"
Black Screws
#8 x 3/4" Screw - 8
SHOWN ACTUAL SIZE
Front Base
#10 x 7/8" Black Screw - 7
SHOWN ACTUAL SIZE
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
IMPORTANT! Before assembly, inspect this product for
damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken.
Contact Fisher-Price® for replacement parts and instructions
if needed. Never substitute parts.
Seat
Bottom
Tubes
Footrest
Plastic
Rings
Seat Bottom
Plastic
Rings
3
• Align the holes in the plastic
rings and the seat bottom tubes.
• Insert a #8 x 3/4" screw through
each plastic ring and into the
seat bottom tubes, as shown.
1
#8 x 3/4" Screw - 4
SHOWN ACTUAL SIZE
• Place the seat bottom face down on a flat surface.
• At an angle, fit the footrest on the seat bottom, as shown.
• Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
• Push the seat bottom tubes back and forth to be sure they
are secured to the seat bottom. If the seat bottom tubes
move, you have probably not fastened them properly.
Remove the screws and check to be sure the screw holes in
the seat bottom tubes and seat bottom plastic rings are
aligned. Replace and tighten the screws.
Plastic
Rings
Seat Bottom Tubes
Footrest
Insert Screws
Here
Plastic
Rings
2
• Slide a seat bottom tube through each set of plastic rings
on the seat bottom.
4
#10 x 7/8" Black Screw - 2
SHOWN ACTUAL SIZE
• Insert two #10 x 7/8" black
screws through the footrest
and into the seat bottom.
• Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Frame Leg
Seat Back
Pin
Seat Back
Pin
Opening
Opening
7
Seat
Bottom
Assembly
• Pull the frame leg out on each frame to open. Make sure it
5
“clicks” into place.
Short Leg
Tube
• Turn the seat bottom assembly upright.
• Fit the seat back pins into the openings in the top side of
the seat bottom assembly.
#10 x 7/8" Black Screw
SHOWN ACTUAL SIZE
Back Base
Hinge
Long
Tapered
Leg Tube
Hinge Rod
8
Front Base
6
• Identify the back and front base. The back base has short leg
tubes and the front base has long, tapered leg tubes.You will
use the back base for the next assembly step.
• Turn the seat assembly face down.
• Insert the hinge rod through the hinge on the seat back
and seat bottom, as shown.
• Insert a #10 x 7/8" black screw into the hinge rod.
• Tighten the screw with a Phillips screwdriver.
Do not over-tighten.
• Set the seat assembly aside for Assembly step 11.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Frame
Decorated
Side
Seat Height
Adjusters
Position 4
Frame
Back
Legs
Press Lever
10
Back Base Hole
• While pressing the levers on the seat height adjusters, lift
them to position 4 on the frame front legs, as shown.
Screw
Retainers
9
Back Base Hole
Seat Assembly
#10 x 7/8" Black Screw - 2
SHOWN ACTUAL SIZE
Screw Retainer - 2
• Position a frame so that the decorated side is outward.
• Insert the back leg of a frame into the back base.
Sockets
Sockets
• Fit a screw retainer over the hole in the back base, as shown.
• Insert a #10 x 7/8" black screw through the screw retainer
and back base.
• Tighten the screw with a Phillips screwdriver. Do not
over-tighten.
• Repeat this procedure to attach the other frame back leg to
the other side of the back base.
Seat Bottom
Tubes
11
• Fit the seat assembly between the two frames.
• Insert the seat bottom tubes into the sockets in each seat
height adjuster.
Hints:
• Be sure the seat height adjusters are in the same position
(position 4).
• You may need to push the frames apart slightly to fit the seat
bottom tubes into the seat height adjuster sockets.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Push
Seat
Push
Seat
Height
Adjuster
Height
Adjuster
Front Leg Hole
Seat Bottom
Tube Ends
13
Screw Retainers
Front Leg Hole
#8 x 3/4" Screw - 2
SHOWN ACTUAL SIZE
• Push each seat height adjuster
to be sure they are completely
on the seat bottom tubes.
• Insert a #8 x 3/4" screw through each seat height adjuster
and the ends of the seat bottom tube.
• Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
Front Base
12
#8 x 3/4" Screw - 2
SHOWN ACTUAL SIZE
#10 x 7/8" Black Screw - 2
SHOWN ACTUAL SIZE
Seat
Height
Screw Retainer - 2
Seat
Height
Adjuster
Adjuster
• Fit the frame front legs onto the front base.
• Fit a screw retainer over a hole in the front leg.
• Insert a #10 x 7/8" black screw through the screw retainer
and front leg.
Seat
Bottom
Tube Ends
• Tighten the screw with a Phillips screwdriver. Do not
over-tighten.
• Repeat this procedure to secure the other end of the front
base with the remaining screw retainer and #10 x 7/8" black
screw.
14
Back and
Bottom View
• From the back and bottom of the assembly, insert a #8 x 3/4"
screw through both seat height adjusters and the ends of
the seat bottom tube.
• Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Pad
Front Base
Holes
Elastic Loops
Wheels
Wheels
Hole
Hole
Back Base
Holes
15
Wheel
Bottom View
• Tip the assembly so that
Peg
the back of seat is flat
16
on the floor and the front
and back bases are
facing up.
• Insert and “snap” the peg
on a wheel into each of
the four holes in the front
and back bases.
Hole
Tabs
Hint: To remove the wheels from the front and back base,
simply pull and remove. Store the wheels in a safe place for
future use.
Elastic Loops
Back and
Bottom View
• Lift the assembly upright.
• From the front of the assembly, place the pad onto the seat.
• Lift the bottom of the pad. Insert the two elastic loops on
the pad through the holes in the seat bottom.
• From the back and bottom of the seat, hook the elastic
loops to the tabs on the seat.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Slot
Crotch
Belt
Pad
Bottom
Slots
19
• Lift the top of the pad.
• Thread the waist/shoulder belts through the bottom slots in
the back of the seat pad.
17
• Insert the crotch belt through the slot in the pad. Make
sure the crotch belt is not twisted.
Upper Shoulder Belt Slots
Lower Shoulder
Belt Slots
Shoulder
Portion
Headrest
Pad Slots
Shoulder
Portion
20
• Fit the top of the pad over the seat back.
• Fold the bottom edge of the pad under the edge of the
seat bottom to fasten it.
• First, insert the shoulder portion of the shoulder/waist belt
through the slots in the headrest pad. Then, insert the shoul-
der portion of the shoulder/waist belt through the slots in the
pad and seat back.
18
• Fold the top of the pad down.
• Remove the shoulder portion of the waist/shoulder belts
by feeding them through the slots in the seat back.
- Use the lower shoulder belt slots for a smaller baby.
- Use the upper shoulder belt slots for a larger baby.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Headrest
Pad Strap
Handle
Elastic
Loop
Elastic
Loop
Tab
Belt
Ends
Tab
21
23
Back View
• Fit the strap on the top of the headrest through the handle.
• From behind the seat, be sure the shoulder portion of the
waist/shoulder belts are secure in the seat back slots.
• Hook the elastic loops on each side of the pad onto the tabs
in the seat back.
Pad
Strap
Handle
Headrest Strap
Small
Fastener
Storage
Caddy
Frame
Tab
Large
Fastener
22
24
Back View
• Fit the pad strap through the handle and press it to the
small fastener on the back of the seat.
• Fit the headrest strap through the handle and press it to the
• At an angle, fit the storage caddy onto the tab on
either frame.
large fastener on the back of the seat.
Assembly is now complete.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Securing Your Child
IMPORTANT! Before each use, inspect this product for
damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken.
Contact Fisher-Price® for replacement parts and instructions
if needed. Never substitute parts.
Anchored
End
Anchored
End
A
B
A
B
Free End
Free End
WARNING
Buckle
2
Prevent serious injury or death
from falls or sliding out.
Tighten
Loosen
The child should be secured in
the high chair at all times by the
restraining system, either in the
recline, semi-recline or upright
position. The restraint belts must
be adjusted to fit your child snugly.
The tray is not designed to hold
the child in the chair.
To tighten the waist belts:
• Feed the anchored end of the waist belt up through the
A
buckle to form a loop
.
B
• Pull the free end of the waist belt
• Repeat this procedure to tighten the other waist belt.
To loosen the waist belts:
.
• Feed the free end of the waist belt up through the buckle to
A
form a loop
.
• Enlarge the loop by pulling on the end of the loop toward
the buckle.
• Pull the anchored end of the waist belt to shorten the free
B
end of the waist belt
.
• Repeat this procedure to loosen the other waist belt.
Waist/Shoulder
Belt
Waist/Shoulder
Belt
Hold
Adjuster
Slide
Pull Strap
Adjuster
Down
Down
Crotch
Belt
3
Tighten
Loosen
1
To tighten the shoulder belts: Hold the adjuster and pull the
front shoulder strap down.
To loosen the shoulder belts: Slide the adjuster down.
Note: After adjusting the restraint system to fit your child,
make sure you pull on it to be sure it is securely fastened.
• Place your child in the seat. Position the crotch belt between
your child’s legs.
• Fasten both waist/shoulder belts to each side of the crotch
belt. Make sure you hear a "click" on both sides.
• Check to be sure the restraint system is securely attached by
pulling it away from your child. The restraint system should
remain attached.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Securing Your Child
Using the Trays
WARNING
Prevent serious injury or death
from falls or sliding out.
The child should be secured in
the high chair at all times by the
restraining system, either in the
recline, semi-recline or upright
position. The restraint belts must
be adjusted to fit your child snugly.
The tray is not designed to hold
the child in the chair.
4
Base Tray
To change shoulder belt slots:
• From the back of the high chair, push the shoulder portion
of the waist/shoulder belts through the seat back slots.
Shoulder
Portion
Armrest
Armrest
5
6
• From the front of the high chair, pull the shoulder portion of
the waist/shoulder belts out and then fit them back through
the desired shoulder belt slots in the headrest pad, seat pad
and the seat back. Pull on the belts to be sure they are
secure in the seat back.
• Fit the base tray onto the seat armrests. Push down until
the base tray "snaps" into place.
Hint: Before use, thorougly wash all parts (the trays) that may
contact food.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Trays
Hint: The base tray can be removed two ways (see steps
Hint: The base tray can be adjusted for your child’s comfort
9 and 10)!
two ways (see steps 7 and 8)!
Base
Tray
Base
Tray
Squeeze
Latch
Squeeze
Latch
Release Bar
9
7
• Squeeze one or both of the latches underneath the base
tray and lift.
• While pushing the release bar on the front of the base tray,
adjust the base tray forward or backward.
Base
Tray
Base
Tray
Squeeze
Latch
Squeeze
Latch
Release
Bar
8
10
• While squeezing the latches underneath the base tray,
adjust the base tray forward or backward.
• While pushing the release bar on the front of the base tray,
pull the tray base towards you and remove.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Trays
Using the Brakes
WARNING
Food Tray
Prevent serious injury or death
from falls or sliding out.
• Always leave wheels locked.
• Never use near stairs.
Base
Tray
11
• Fit the food tray into the base tray, as shown.
Hint: Before use, thorougly wash all parts (the trays) that may
contact food.
Wheels
Tab
Tab
12
Lift
Tab
Press
Tab
Lock
Unlock
TO LOCK: Press the tab on all four wheels down until you
hear a “snap”.
TO UNLOCK: Lift the tab on all four wheels up.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Seat
WARNING
Hint: Adjust the seat angle to any of three positions: Upright,
Semi-Recline or Recline.
Prevent serious injury or death
from falls or sliding out.
Upright
Semi-Recline
It is recommended that the high
chair be used in the upright position
only by children capable of sitting
upright unassisted.
Recline
Hint: Adjust the seat height to any of seven positions!
Seat Height
Adjuster
14
To adjust the seat angle:
Press Lever
• Squeeze the seat back
handle and push the seat
back forward or, pull it
backwards to the
desired position.
• Push the seat back to be
sure it is latched in position.
Squeeze
13
Back View
To adjust the seat height:
4
• Press the levers on both seat
height adjusters and lift or lower
the seat to the desired height.
• Make sure both sides of the seat
are adjusted to the same height.
Push the seat bottom to be sure the seat is locked in place.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Storage
Care
• The pad and headrest are machine washable. Wash the pad
and headrest separately in cold water on the gentle cycle.
Do not use bleach. Tumble dry separately on low heat and
remove promptly.
• The frame and base tray may be wiped clean using a mild
cleaning solution and a damp cloth. Do not immerse the
base tray.
• The food trays are dishwasher safe. Simply remove the food
tray from the base tray and place in your dishwasher.
To remove the pad:
• Remove the four elastic loops from the pegs on the
underside and back of the seat.
Base
Tray
• Unfasten the pad strap and headrest strap from the
seat back.
Hole
• Feed the shoulder portion of the waist/shoulder belts
through the slots in the seat back, the pad and the headrest.
• Feed the waist portion of the waist/shoulder belts and
crotch belt down through the slots in the seat.
Peg
• Remove the waist/shoulder belts and crotch belt through
the slots in the pad.
• Unfasten the pad fasteners from the front edge of the
seat bottom.
• Remove the pad.
15
To replace the pad and headrest: refer to Assembly
steps 16-23.
IMPORTANT! Never use this product without the
restraint system. Replace the waist/shoulder belts and
crotch belt.
• Fit the holes on the base tray latches onto the pegs on the
back of the high chair frame.
Pull Frame
Release Latch
For other countries, outside the United States:
Canada: call 1-800-567-7724, or write to: Mattel Canada Inc., 6155
Freemont Blvd. Mississauga, Ontario L5R 3W2.
Great Britain: telephone 01628 500302.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Fisher-Price, Inc., a subsidiary of Mattel, Inc.
East Aurora, New York 14052, U.S.A.
16
©2002 Mattel, Inc. All Rights Reserved.
® and TM designate U.S. trademarks of Mattel, Inc.
• With the legs all the way open, lower the seat to position 1
(the lowest position).
• Pull the frame release latches forward and push the rear legs
toward the front legs.
Printed in China
B2105-0920
Download from Www.Somanuals.com. All Manuals Search And Download.
|