Fisher Paykel Garbage Disposal WD1001 User Manual

Fisher & Paykel  
Waste  
Disposal  
User’s Guide  
(Models WD1001 and WD2002)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FISHER & PAYKEL WASTE DISPOSAL -  
INSTALLATION INSTRUCTIONS  
IMPORTANT  
Before you start to install your FISHER & PAYKEL Waste disposal please read all of these  
instructions carefully. This set of instructions is general: local building codes take precedence  
over the instructions in this guide and your installation must conform to the building codes in your  
area. Be sure to retain this set of instructions for future reference.  
TOOLS REQUIRED FOR INSTALLATION  
You may need the following tools and supplies when installing your disposer:  
(ILLUSTRATION #1)  
Pipe wrench  
Hacksaw  
Plumber’s Rod  
Phillips Screw Driver  
Rubber Mallet  
Electrical Switch  
(20 amp rating)  
- 3 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
UNPACKING YOUR WASTE DISPOSAL  
Remove the waste disposal from the packing carton, being careful not to misplace any of the  
pieces. Inside the carton you should find the following: (ILLUSTRATION #2)  
1. Sink Drain plug *  
2. Sink Frange *  
3. Sink Flange Rubber Gasket *  
4. Sink Flange Fiber Gasket *  
5. Mount Ring *  
6. Hinged Clamp *  
7. Waste Pipe  
8. Flange & Screws  
9. Rubber Gasket  
10. Hexagon Wrench  
ILLUSTRATION #2  
If any parts are missing contact your dealer before beginning installation.  
REMOVE OLD DISPOSER OR SINK WASTE REDUCER  
IF REMOVING AN OLD DISPOSER & INSTALLING A  
FISHER & PAYKEL WASTE DISPOSAL…  
Disconnect the drain where it connects to the old  
disposer’s waste pipe. (ILLUSTRATION #3). Then  
dismount the disposer from the sink mounting  
assembly. Finally remove the sink flange from the  
topside of the sink (ILLUSTRATION #4).  
ILLUSTRATION #3  
IF REMOVING A SINK WASTE REDUCER  
ILLUSTRATION #4  
If your sink is equipped with a sink waste reducer  
instead of a waste disposer, remove the nut or  
threaded ring holding the waste reducer in place.  
(ILLUSTRATION #5).  
ILLUSTRATION #5  
- 4 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Then push the waste reducer up through the drain opening.  
(ILLUSTRATION #6)  
If the drain opening on your sink is covered with sealant,  
remove as much of the putty as possible from the rim of the  
sink drain hole.  
Unless you have a new home, be sure that the existing trap  
and drain lines are clear. If the drain line is not clear, use a  
plumber’s rod or auger to remove all impediments.  
INSTALL THE SINK MOUNT FLANGE  
If a hole needs to be cut in the sink, it should be diameter  
87-92mm.  
PRESS DOWN FIRMLY  
WHEN ASSEMBLING  
First, place the sink flange rubber gasket over the sink flange’s  
threaded ring. Insert the flange and rubber gasket in to the  
sink drain opening from the top side of the sink. It is not  
necessary to use plumber’s putty when installing the sink  
flange.  
Second, place the sink flange fiber gasket over the sink  
flange’s threaded ring. Next, attach the mount ring and tighten  
with one hand while using the other hand to press down on the  
sink flange. (ILLUSTRATION #7). Hand tighten as tight as  
possible. Do not try to tighten with a wrench or hammer.  
ILLUSTRATION #7  
- 5 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MOUNTING THE DISPOSER  
1.  
2.  
Loosen and remove the hinged clamp. (ILLUSTRATION #9).  
The rubber splash guard should be attached to the waste disposal unit and not to the sink  
flange. Using two hands, push the disposer upwards so that the inner groove on the splash  
guard locks on to the sink flange. If necessary, use cooking oil to lubricate the inner rim on  
the exposed side (top side) of the splash guard. Once engaged, the disposer will hang freely  
by itself. (ILLUSTRATION #10).  
3.  
4.  
Place the hinged clamp around the splash guard and lock in place. (ILLUSTRATION #11 &  
#12).  
The appliance must be installed so that the reset button is readily accessible.  
ILLUSTRATION #9  
ILLUSTRATION #10  
ILLUSTRATION #11  
ILLUSTRATION #12  
PLUMBING CONNECTION  
1.  
2.  
Check inside the disposer to make sure that no foreign  
objects are inside the grinding hopper.  
Rotate the disposer so that the discharge outlet faces  
you. (ILLUSTRATION #13).  
- 6 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3.  
4.  
Slide the waste pipe flange on to the waste pipe.  
Attach the rubber gasket to the waste pipe so that the thin  
lip is facing the disposer. (ILLUSTRATION #14)  
Insert the non-notched end of the waste pipe flange into the  
slot below the waste outlet on the waste disposer.  
(ILLUSTRATION #15)  
5.  
6.  
7.  
Use the screw to tighten the waste pipe to the disposer.  
Rotate the disposer so that the waste pipe lines up with the  
drain trap. (ILLUSTRATION #16).  
ILLUSTRATION #14  
8.  
9.  
Once the waste pipe is lined up use a pipe wrench to  
tighten the slip nut on the drain trap. ILLUSTRATION #17).  
If fitted to a double sink, the use of separate traps for the  
disposer and the sink are recommended.  
10. Make sure that the hinged clamp is locked firmly in place.  
ILLUSTRATION #15  
ILLUSTRATION #16  
ILLUSTRATION #17  
- 7 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ELECTRICAL CONNECTIONS  
ELECTRICAL CONNECTIONS FOR A FACTORY WIRED DISPOSER:  
Your FISHER & PAYKEL waste disposal is equipped with a pre-wired power cord, simply plug it in.  
Electrical connections should be done by a registered electrician. Your FISHER & PAYKEL waste  
disposal is equipped with a standard 3 pin plug. An earthed 3 pin power socket should be  
mounted in the cupboard under the sink. Power to the socket must be controlled by a standard  
wall switch positioned a minimum of 500 mm from the sink.  
As per your local Regulations.  
CONGRATULATIONS  
The installation of your FISHER & PAYKEL waste disposal is now complete. Plug the power cord  
in and read the following safety instructions before proceeding to the section explaining the proper  
usage and maintenance of your new waste disposer.  
INSTRUCTION PERTAINING TO A RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO  
PERSONS  
IMPORTANT SAFETY INSTRUCTIONS  
WARNING: When using electric appliances, basic precautions should always be followed  
including the following:  
1.  
2.  
Read all instructions before using the appliance.  
To reduce the risk of injury, close supervision is necessary when an appliance is used near  
children.  
3.  
4.  
Do not put fingers or hands into the waste disposal unit.  
Turn the power switch to the off position before attempting to clear a jam or remove an object  
from the dispenser.  
5.  
6.  
7.  
When attempting to loosen a jam in the waste disposal use the hexagonal wrench provided.  
See safety features for further information.  
When attempting to remove objects from the waste disposal, use long handled tongs or  
pliers.  
Do not put the following into the disposer:  
a.  
b.  
c.  
d.  
e.  
f.  
Shells  
Drain cleaner  
Glass, china or plastic  
Large, whole bones  
Metal, such as bottle caps, tin cans, or aluminium foil  
Whole corn husks  
g.  
Any fibrous materials  
8.  
When not operating the disposer, leave the sink drain plug in place to reduce the risk of  
objects falling into the disposer.  
- 8 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAVE THESE INSTRUCTIONS  
OPERATING INSTRUCTIONS  
1.  
2.  
Remove the sink drain plug  
Turn on the cold water to a medium-high flow, allowing the water to flow into the waste  
disposer.  
3.  
4.  
Turn on your waste disposer.  
Put all food waste into the disposer while the disposer is operating and the water running. Do  
not put your hand into the disposer.  
5.  
6.  
7.  
Let your disposer continue to run for about half a minute after the grinding has stopped.  
Turn off the disposer.  
Turn off the water when the impellers have stopped spinning.  
CAUTION  
While your FISHER & PAYKEL waste disposal will have no problem grinding food waste, some  
items should never be placed into it. In particular, do not attempt to grind the following:  
Metal: Silverware, nails, tacks, wire, bread bag ties, staples  
Glass: Jars, bottles, pieces of pottery or crockery  
Lye or drain cleaning chemicals  
Excessive quantities of fat or grease  
Any fibrous materials  
Remember, your FISHER & PAYKEL waste disposal is designed for grinding food waste only.  
With proper use and care it will provide you with many years of trouble free service.  
Note: Do not operate your garbage disposer while it is upside down.  
If the supply cord is damaged it must be replaced by a qualified electrician.  
- 9 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY FEATURES  
Your disposer is equipped with an overload protector which prevents the disposer from running  
should it overload. Overload generally occurs when a foreign object has fallen into the disposer  
and jammed the impellors, thus preventing the motor from turning. Overload may also occur if you  
have put too much food waste into the disposer at one time. If overload occurs, turn off the  
disposer and remove the foreign matter or food waste from the disposer. Insert a hex wrench into  
the opening at the bottom of the motor shaft and rotate the tool clockwise (ILLUSTRATION #18).  
Wait five to ten minutes, push the red reset button on the bottom of the disposer, and restart the  
machine.  
Hexagon  
Reset  
wrench  
button  
ILLUSTRATION #18  
DISPOSER MAINTENANCE  
With normal usage your disposer should not require any special care. The motor is permanently  
lubricated and will not require oiling under normal usage conditions.  
If used according to the operating instructions above, your disposer should not require cleaning.  
However, should it start to smell, grinding a tray of ice cubes in the disposer will clean the grinding  
components. Grinding a lemon, cut into quarters, will also give your disposer a fresh, clean smell.  
- 10 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Express Warranty  
Fisher & Paykel Appliances Limited  
FULL TWO YEAR WARRANTY FROM DATE OF PURCHASE  
FISHER & PAYKEL UNDERTAKES TO  
Repair or, at its option, replace without cost to the owner either for material or labour any part of  
the product which is found to be defective within TWO YEARS of the date of purchase.  
THIS EXPRESS WARRANTY DOES NOT INCLUDE:  
A.  
Service calls to:  
1.  
2.  
3.  
4.  
Correct the installation of the Product.  
Instruct you how to use the Product.  
Replace house fuses or correct house wiring or plumbing.  
Replace light bulbs.  
B.  
Damage when the product has been used otherwise than:  
1.  
2.  
In normal domestic use or  
In accordance with the Product’s Use & Care booklet.  
C. Damage when the Product has been dismantled, repaired or serviced by other than a  
FISHER & PAYKEL AUTHORISED SERVICE CENTRE.  
D. Normal recommended maintenance as set out in the Product’s Use & Care booklet.  
E.  
F.  
Cartage (or mileage) when the product is situated more than 50kms from a FISHER &  
PAYKEL AUTHORISED SERVICE CENTRE.  
Damage to the Product caused by accident, neglect, misuse or Act of God.  
SERVICE UNDER THIS EXPRESS WARRANTY MUST BE PROVIDED BY A FISHER & PAYKEL  
AUTHORISED SERVICE CENTRE. SUCH SERVICE SHALL BE PROVIDED DURING THEIR  
NORMAL BUSINESS HOURS. THIS EXPRESS WARRANTY CERTIFICATE SHOULD BE  
SHOWN WHEN MAKING ANY CLAIM.  
NOTE: THIS EXPRESS WARRANTY IS OFFERED AS AN EXTRA BENEFIT AND DOES NOT  
AFFECT YOUR LEGAL RIGHTS.  
Customer: _______________________ Date of Purchase _________________________  
MODEL  
SERIAL NO.  
This Warranty applies only to an appliance purchased in New Zealand.  
Please turn over  
- 11 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FISHER & PAYKEL WASTE DISPOSAL INSTALLATION DIMENSIONS  
MODEL  
WD1001  
A
B
C
D
E
320  
312  
175  
159  
127  
127  
170  
170  
114  
114  
WD2002  
Measurements in mm  
Dimensions:  
A.  
B.  
C.  
D.  
E.  
Distance from bottom of sink to bottom of disposer  
Width of disposer  
Distance from centre of disposer to centre of drain pipe  
Length from bottom of sink to centre of drain opening  
Length from centre of drain opening to bottom of drain pipe  
- 12 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
We want you to be a happy satisfied customer  
If you need service or assistance, we suggest you follow these steps  
1.  
Before calling for assistance:  
Check the things you can do yourself. Ensure that the appliance is correctly installed and  
that you are familiar with it’s normal operation.  
2.  
If you need service:  
Contact the Dealer from whom the appliance was purchased, who will arrange service or  
advise you where to obtain service.  
Your Authorised Service Centre  
Is: ...............................................................  
Telephone no: ...........................................  
Fisher & Paykel has a network of FISHER & PAYKEL AUTHORISED SERVICE CENTRES whose  
fully trained technicians can carry out any service necessary on your appliance.  
3.  
For further assistance (if necessary)  
Fisher & Paykel Customer Care Centre  
PO Box 58-732  
Greenmount  
Freephone 0800 37 2273  
Telephone (09) 273 0448  
Facsimile (09) 273 0656  
AUCKLAND  
One of our Customer Representatives can instruct you on how to obtain satisfactory operation from  
your appliance or, if necessary, recommend a Fisher & Paykel Authorised Service Centre in your  
area.  
If you call or write, please provide your name and address, model number, serial number, date of  
purchase, and a complete description of the problem. This information is needed in order to better  
respond to your request for assistance.  
571972 ERC B  
- 13 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Echo Blower 11 Dec User Manual
Euro Pro Electric Steamer KS315W User Manual
Evolve Showerheads Plumbing Product Evolve Showerhead User Manual
Extron electronic Stereo Amplifier DVI DA4 User Manual
Fellowes Paper Shredder 320 320C 320 2HS 380 380C User Manual
FujiFilm Computer Monitor BB10768 3011 User Manual
FujiFilm Digital Camera Z110 User Manual
Gaggenau Telescope WS461710 User Manual
Garmin GPS Receiver 190 00266 00 User Manual
GBC Laminator H410 User Manual