US CA
part number 526607 N
05/2005
(page 1 of 12)
R
INSTALLATION INSTRUCTIONS
(NOTE: FOR INTEGRATED PANEL PREPARATION INSTRUCTIONS REFER TO SUPPLIED SHEET)
SINGLE DS603 MODELS
DS603 PREFINISHED (shown left)
DS603 FLAT DOOR (not shown)
DS603I INTEGRATED (shown right)
DOUBLE DD603 MODELS
DD603 PREFINISHED (shown left)
DD603 FLAT DOOR (not shown)
DD603I INTEGRATED (shown right)
NOTE TO THE INSTALLER
WARNING!
Before installing the DishDrawer® , remove the house fuse or open
the circuit breaker. Ensure all water connections are turned OFF. It is
the responsibility of the plumber and electrician to ensure that each
installation complies with all Codes and Regulations.
1. Read these instructions completely and carefully.
2. Installation of this DishDrawer® requires basic
mechanical and electrical skills.
3. Be sure to leave these Instructions with the Customer.
4. At the completion of the DishDrawer® installation, the
Installer must perform Final Check List as per Section 12
of these Installation Instructions.
5. Remove all packaging materials supplied with the
DishDrawer®.
Important!
These instructions must be followed precisely to ensure correct
venting and operation of the DishDrawer®
related to the incorrect installation, the installer will be liable for any
repairs.
. In the event of a fault
Important!
The DishDrawer® MUST be installed to allow for future removal
from the enclosure if service is required.
6. This dishwasher is manufactured for indoor use only.
Important!
Improper installation is not covered under the Warranty.
NOTE TO THE CUSTOMER
Important!
Keep these Installation Instructions with your User Guide
for future reference. The DishDrawer® must be securely
anchored before it is operated.
If the DishDrawer® is to be relocated from one installation to
another it must be kept upright to avoid damage from water spillage.
Download from Www.Somanuals.com. All Manuals Search And Download.
R
DOUBLE MODELS
ꢎ
SERVICES SPECIFICATIONS
ꢀꢀ ꢄ w
ꢎ
ꢉꢆ
ꢀꢁ ꢄ w
ꢉꢆ
*
ꢎ
ꢃꢎꢇNNꢈ
ꢀꢀ ꢄ w
ꢉꢆ
ꢃꢋꢃNNꢈ
ꢃ
ꢃꢎꢇNNꢈ
ꢄ w
ꢉꢆ
ꢅNNꢈ
WATER CONNECTION
Recommended HOT
(Maximum 140°F/60°C).
Supplied hose to suit 3/8” (9mm)
male compression fitting.
**
#
ꢃ
ꢄ w
ꢆꢊ
ꢀNNꢈ
5BC
4JEFꢂ7JFX
WATER SOFTENER MODELS
Refer to your DishDrawer® User Guide for
how to set up your water softener.
ꢉꢃ
ꢀꢇ ꢄ w
ꢁꢀ
ꢃꢀꢇNNꢈ
%SBXFSꢂ0QFO
WATER PRESSURE
Water Softener Models
Other Models
Maximum
145 p.s.i. (1000kPa)
145 p.s.i. (1000kPa)
Minimum
14.5 p.s.i. (100kPa)
4.3 p.s.i. (30kPa)
ꢁ
ꢀwꢂꢍꢂꢊ ꢄ w
Prefinished model shown
* For an Integrated DishDrawer® the
ꢅ
ꢃꢇꢍꢉꢉꢇNNꢈ
product depth is specified with an
11
/ ” (18mm) Integrated Panel thickness.
16
** Depth of product excludes Curvature (13/16” (30mm) Prefinished only,)
or Handle.
DRAIN CONNECTION
3
5
5
5
Drain Hose Joiner to suit Ø /4” ± /64”, Ø /8” ± /64” and
5
Ø1” ± /64” waste tees.
TOE KICK DEPTH
ELECTRICAL CONNECTION
Prefinished & Flat Door 2”-43/8” (50-110mm);
Integrated 5” (127mm) less the Toe Kick Panel thickness. Minimum Panel
110-120 VAC power outlet, 9 Amps Minimum.
3
thickness using the supplied screws is /8” (9mm).
LENGTH OF SERVICES (FROM PRODUCT EXIT POINT)
Drain hose - 889/16” (2250mm)
Inlet hose - 687/8” (1750mm)
Power supply cord - 44” (1125mm)
NOTE: Services approximately exit product 77/16” (189mm) from left;
215/8” (550mm) from front; 311/4” (793mm) from top.
# DOOR FRONT HEIGHT
Prefinished & Flat Door 305/64” (764mm);
Integrated 281/4” (717.5mm) minimum.
THE CAVITY
ꢊꢂꢃꢄꢉꢆw
ꢉꢇꢋꢌꢃNNꢈ
4DSFXꢂꢀꢁꢂꢃwꢄ ꢉꢊNNꢈ
ꢂꢁꢅw
ꢉꢁNNꢈ
GSPNꢂGSPOUꢂPGꢂDBCJOFUSZ
VœÕ˜ÌiÀÌœ«
+
+
“œˆÃÌÕÀi
«ÀœÌiV̈œ˜
Ì>«i
.PJTUVSF
1SPUFDUJPO
5BQF
ꢋꢇ×
ꢂꢁꢅwꢄ ꢉꢁNNꢈ
.JOꢂUIJDLOFTT
PGꢂDBWJUZꢂTJEFT
JTꢂꢃꢄꢅwꢂ ꢉꢆNNꢈ
ꢉꢉꢄꢀwꢂ ꢁꢅNNꢈ
TFSWJDFTꢂIPMF
These marks indicate mounting tab screw
locations (refer to step 1 page 7)
JNNFEJBUFMZ
BEKBDFOUꢂUPꢂDPSOFSꢏ
DBOꢂCFꢂFJUIFSꢂTJEF
w
ꢅ
ꢎ ꢄ
ꢈ
N
ꢁꢂꢉꢁꢄꢉꢆw
ꢋꢎNNꢈ
NOTE: All depth measurements are taken
from the front face of the adjacent cabinetry.
ꢂꢂꢂꢉꢋꢂ
ꢃꢇꢃN
ꢀꢀꢂꢎꢄꢅwꢂ ꢃꢅꢇNNꢈ
UISPVHIPVUꢂDBWJUZ
WARNING!
Be sure the edges of the services hole
are smooth or covered. If the services
hole is through a metal partition the hole
must be protected with the Edge Protector
provided to prevent damage to the power
cord or hoses.
ꢀꢁꢂꢃꢄꢅwꢂ ꢆꢇꢇNNꢈ
3
Download from Www.Somanuals.com. All Manuals Search And Download.
R
DOUBLE MODELS
PLUMBING OPTIONS
OPTION 1
DishDrawer® and Standpipe Ø11/2” (38mm) with Air Gap.
OPTION 2
DishDrawer® with Waste Disposal.
OPTION 3
DishDrawer® using Air Break with Drain Hose Joiner.
NOTE: Prefinished Model is shown. There is no variation
in plumbing between models. Option 1 is the preferred
option. Drains will need to be separated to satisfy Kosher
requirements. We suggest you confirm acceptability with
your local Rabbi in respect to Kosher installations.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
R
SINGLE MODELS
SERVICES SPECIFICATIONS
ꢀꢀꢎꢄꢉꢆw
ꢃꢎꢇNNꢈ
ꢃꢄꢉꢆw
ꢀꢁꢎꢄꢉꢆw
ꢎ
*
ꢀꢀ ꢄꢉꢆ
ꢅNNꢈ
ꢃꢋꢃNNꢈ
ꢃꢎꢇNNꢈ
WATER CONNECTION
Recommended HOT
(Maximum 140°F/60°C).
Supplied hose to suit 3/8”(9mm) male
compression fitting.
ꢃꢄꢆꢊw
ꢀNNꢈ
**
5BC
ꢉꢆꢁꢄꢁꢀ
4JEFꢂ7JFX
WATER SOFTENER MODELS
Refer to your DishDrawer® User Guide
for how to set up your water softener.
ꢊꢇꢋNNꢈ
ꢀꢇꢉꢃꢄꢁꢀw
ꢃꢀꢇNNꢈ
%SBXFSꢂ0QFO
Maximum
145 p.s.i. (1000kPa)
145 p.s.i. (1000kPa)
Minimum
14.5 p.s.i. (100kPa)
4.3 p.s.i. (30kPa)
WATER PRESSURE
Water Softener Models
Other Models
Prefinished model shown
*For an Integrated DishDrawer® the product depth is specified with an
/ ” (18mm) Integrated Panel thickness.
16
11
** Depth of product excludes Curvature (13/16” (30mm) -
prefinished only), or Handle.
DRAIN CONNECTION
3
5
5
5
Drain Hose Joiner to suit Ø /4” ± /64” and Ø /8” ± /64” waste tees.
LENGTH OF SERVICES (FROM PRODUCT EXIT POINT)
Drain hose - 889/16” (2250mm)
Inlet hose - 687/8” (1750mm)
ELECTRICAL CONNECTION
110-120 VAC power outlet, 4.5 Amps Minimum.
Power supply cord - 44” (1125mm)
NOTE: Services approximately exit product 77/16” (189mm) from left;
215/8” (550mm) from front; 151/2” (393mm) from top.
WEIGHT
Full 93 lb (42kg) Prefinished
Empty 62 lb (28kg) Prefinished
THE CAVITY
ꢂꢁꢅw
ꢉꢁNNꢈ
VœÕ˜ÌiÀÌœ«
“œˆÃÌÕÀi
«ÀœÌiV̈œ˜
Ì>«i
.PJTUVSF
1SPUFDUJPOꢂ5BQF
ꢋꢇ×
ꢂꢁꢅwꢄ ꢉꢁNNꢈ
ꢉ
ꢉ ꢄ wꢂ ꢁꢅNNꢈꢂTFSWJDFT
ꢀ
.JOJNVN
IPMFꢂJNNFEJBUFMZꢂ
BEKBDFOUꢂUPꢂDPSOFSꢏ
DBOꢂCFꢂFJUIFSꢂTJEF
UIJDLOFTTꢂPG
DBWJUZꢂTJEFT
ꢉꢁ
ꢋꢎNNꢈ
+
+
ꢁ
ꢄ w
ꢉꢆ
ꢃ
JTꢂ ꢄ wꢂ ꢉꢆNNꢈ
ꢅ
+
+
ꢎ
ꢀꢀ ꢄ wꢂ ꢃꢅꢇNNꢈ
ꢅ
ꢃ
ꢀ ꢄ w
ꢅ
UISPVHIPVUꢂDBWJUZ
R
ꢆꢎNNꢈ
ꢃ
ꢀꢁ ꢄ wꢂ ꢆꢇꢇNNꢈ
ꢅ
Important!
Adjacent cabinetry must
not extend above
cavity base.
WARNING!
Be sure the edges of the services hole
are smooth or covered. If the services
hole is through a metal partition the
hole must be protected with the Edge
Protector provided to prevent damage to
the power cord or hoses.
These marks indicate mounting
tab screw locations
(refer to step 1 page 7)
NOTE: All depth measurements are taken
from the front face of the adjacent cabinetry.
NOTE: To align drawer front to adjacent
cabinetry, the product to countertop
clearance can be increased from 1/8” (3mm).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
R
SINGLE MODELS
PLUMBING OPTIONS
OPTION 1
DishDrawer® and Standpipe Ø11/2” (38mm) with Air Gap.
OPTION 2
DishDrawer® with Waste Disposal.
OPTION 3
DishDrawer® using Air Break with Drain Hose Joiner.
NOTE: Prefinished Model is shown. There is no variation
in plumbing between models. Option 1 is the preferred
option. Drains will need to be separated to satisfy Kosher
requirements. We suggest you confirm acceptability with
your local Rabbi in respect to Kosher installations.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
R
INSTALLATION INSTRUCTIONS
PLEASE NOTE: Your model of DishDrawer® may differ from the model shown in the installation
diagrams. Installation is similar for all models for either Single or Double models. Information referring
to Single models only is highlighted in blue. Installation diagrams have been simplified to enable
clearer instruction. FOR INTEGRATED PRODUCTS FOLLOW THE INTEGRATED PANEL PREPARATION
INSTRUCTIONS P/N 526608, BEFORE MOVING THE PRODUCT INTO THE CAVITY.
READ THESE INSTRUCTIONS
COMPLETELY AND CAREFULLY.
STEP 1: MOVING THE PRODUCT INTO THE CAVITY
MOUNTING TAB OPTIONS
The mounting tabs are in pairs, one on each side of the product. They are
used to secure the product to the cavity sides. Installation requires two
sets of tab pairs be used. DOUBLE MODELS ONLY - A and B tab pairs
OR B and C tab pairs may be used. All tabs would be optimum.
2
If the top installation tabs C are to be used, fit to the chassis by
inserting into the top slots as shown. Ensure the tabs are fully
locked in place.
1
1
Optional Flexible Extrusion
2
If the cavity is 24” x 341/2” (610mm x 876mm) flexible extrusions
can be attached along the top and sides of the product. Open the
drawer(s) to expose the chassis trim. Remove extrusion backing
and adhere to the side and top of DishDrawer®. Refer to the
drawing for correct placement.
Be sure that extrusions do not prevent the drawer from closing
completely.
3
Check cavity for any obstructions that may interfere with sliding
the product back. DOUBLE MODELS ONLY - loosen the feet first.
3
4
Push product into cavity to suit adjacent cabinetry. Do not push
4
middle of drawer(s). Be sure inlet, drain hose(s) and power supply
cord are not restricted or damaged by carefully pulling all excess
length through the services hole, while the product is being pushed
back into the cavity.
Important!
DO NOT push
middle of drawer(s).
WARNING!
Be careful of
sharp edges.
FOR SINGLE MODELS, check that the base of the product is not
bowed. Do not rest single models on your knee when moving them
into the cavity.
STEP 2: REMOVING THE TUB
Important! (SINGLE MODELS ONLY).
The product may move. Mark chassis position on cavity.
5
6
SINGLE MODELS ONLY. Gently open the drawer and mark the
chassis position on the cavity, before removing the tub.
5
7
Open the drawer (bottom drawer in DOUBLE MODELS). Release
the tub by depressing the right hand tub clip and pushing it back
13/16” (30mm). Repeat on the left hand side.
6
7
8
9
Lift the tub up off the drawer runners.
Slide both runners back into the product.
Place the tub onto the floor.
For SINGLE MODELS, depending on the height of the cavity, the tub
will need to be supported, eg on a chair.
9
8
7
Download from Www.Somanuals.com. All Manuals Search And Download.
R
INSTALLATION INSTRUCTIONS
STEP 3: ADJUSTING THE FEET (DOUBLE MODELS ONLY)
DOUBLE MODELS ONLY
Adjust the height of the product to suit the cabinetry, by turning the
feet from inside the product using a wrench or M5 socket.
10
TIP - gently take the load off each foot using the slide and
then turn by hand.
3
/ ” (5mm)
16
NOTE: For integrated products, the upper panel may be
aligned with the top of the adjacent cabinetry, provided
3
a minimum
maintained.
/16” (5mm) clearance from the counter is
Important!
The product must be levelled to within 3/32” (2.5mm) from front to
back, and side to side.
Important!
The product should NOT support any part of the kitchen cabinetry.
TIP - Place a spirit level on the drawer runners to level the
product.
10
STEP 4: SECURING THE PRODUCT
SINGLE MODELS ONLY
Check the position of the chassis is still where marked on the cavity,
before securing the product.
11
11
There are four 5/8” (16mm) round holes, two on the left and two on
the right hand side in the sound insulation. These provide access to
the mounting tabs.
12
To secure the product to the cabinetry use a 5/8” (16mm)
Phillips screw in each mounting tab.
Make sure the sound insulation is positioned correctly before
continuing installation.
12
13
DOUBLE MODELS ONLY
13
Screw the two top tabs to the underside of bench. Use the supplied
5
Phillips /8” (16mm) screws. Tabs can accommodate a maximum of
3/4” (19mm) vertical gap.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
R
INSTALLATION INSTRUCTIONS
STEP 5: ELECTRICAL CONNECTION
WARNING!
If permanently connecting be
sure the power is isolated.
WARNING!
The product MUST NOT be
plugged in at this stage.
14
14
Be sure there is a power outlet in reach of the supplied power cord.
If there is not a suitable outlet available then have one installed by a
qualified electrician.
Do not use an extension cord.
This view shows the bottom left-hand rear corner with the cover removed
Alternatively, the DishDrawer® may be permanently connected to a
flexible conduit.
15
Remove the power supply cord. Remove round knock-out for cable
clamp. Fit suitable cable clamp for the conduit and terminate the
wiring as shown. Terminate the ground wire using the saddle that
was used on the existing earth.
15
WARNING!
This must only be done by a certified person.
STEP 6: REFITTING THE TUB
Important!
Before refitting the tub, be sure the hoses are not twisted and the
latches at the rear of each drawer runner are facing forward.
To refit the tub, make sure both of the latches at the rear of each
16
drawer runner are facing forward. Ensure hoses are hooping
upward. Place the tub on the half open drawer runners and close
the drawer.
16
17
17
Check the tub clips have reset on both sides of the tub. If not, pull
the tub clips forward until the tub clip button is reset.
Important!
Be sure the tub clips on both sides are reset.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
R
INSTALLATION INSTRUCTIONS
STEP 7: CONNECTING THE DRAIN HOSE(S)
DishDrawer® with Hose Joiner (see Plumbing Options).
Remember to slip the wire clip(s) on the drain hose(s) first.
18a
18a Slip a wire clip over each drain hose, then push the hoses into
the Drain Hose Joiner firmly, 5 clicks. Position the wire clip(s)
between the two positioning ribs on the Drain Hose Joiner.
Attach the Drain Hose Joiner to the waste tee (see Plumbing
Options). Ensure a snug fit. If required a hose clamp may be used.
18b
When using the standpipe option (see Plumbing Options), hose(s)
19
should not extend further than 43/4” (120mm) down the standpipe,
in order to prevent siphoning.
19
Attach the Drain Hose Support to the cabinetry (with the screw
supplied) to prevent siphoning and to keep the drain hose(s)
from kinking. If required, the Drain Hose(s) may be trimmed to a
suitable length.
18b
Important!
1
Minimum hole size to be connected to the waste tee is /2”
(12.7mm).
Be sure the Drain Hose(s) are fully extended to prevent sagging
(see diagram to the left).
The Drain Hose support must be used.
Drain Hose joiner must not support weight of hoses. Keep
excess length of Drain Hose on the DishDrawer® side of the
Drain Hose support or trim to suit.
STEP 8: CONNECTING THE INLET HOSE
Important!
WARNING!
DO NOT cut the inlet hose.
DO NOT plug the product in
at this stage.
20
Connect the Inlet Hose to the water supply. Be sure the sealing
washer is in place. The hose coupling must be tightened a further
half turn after seal contact.
TIP - Turn the water valve ON to check for any leaks.
Alternatively flexible stainless steel hose can be plumbed directly to
the inlet valve using a 3/8” brass adaptor (p/n 526161) available from
the nearest Fisher & Paykel Authorized Service Agent.
WATER
SUPPLY
20
NOTE: SINGLE MODELS DO NOT HAVE A TOE KICK TO
INSTALL. PROCEED TO STEP 12 FINAL CHECK LIST.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
R
INSTALLATION INSTRUCTIONS
STEP 9: MEASURING THE TOE KICK (DOUBLE MODELS ONLY)
Partially open the bottom drawer. Turn Prefinished Toe Kick
upside down and hold vertically against the bottom edge of the
21
Tub side (not the drawer front).
Mark the position of the bottom edge of the Tub side on the Toe Kick.
Choose the nearest groove to the pencil mark which will result
in the shortest Toe Kick.
21
Bottom edge
of tub side
STEP 10: TRIMMING THE TOE KICK (DOUBLE MODELS ONLY)
Important!
22
Before cutting ensure the Toe Kick is positioned on a wooden
chopping board to avoid damage to surrounding area.
On the chosen groove cut down the vertical ribs at the centre and
22
the ends using a knife. Cut along full length with a knife. Turn Toe
Kick over, bend and then cut from front. Sand or scrape bottom edge
to remove rough patches.
WARNING!
Remove all sharp edges
23
23 To avoid a cutting hazard remove all sharp edges after trimming.
24
Remove Toe Kick tabs by snapping them off.
24
11
Download from Www.Somanuals.com. All Manuals Search And Download.
R
INSTALLATION INSTRUCTIONS
STEP 11: FITTING THE TOE KICK TO THE PRODUCT (DOUBLE MODELS ONLY)
Toe kick
mounting rails
25
Partly open bottom drawer. Position Toe Kick behind door and slide
onto the mounting rails on the underside of tub.
25
Close bottom drawer, check if flush with adjacent cabinetry.
If required open drawer and adjust.
26
Note: Clearance between Toe Kick and floor must be
15
/ ” (12mm) minimum.
32
When Toe Kick is in position, open bottom drawer and gently fasten
the Toe Kick screws, on each side.
Important!
DO NOT over tighten screws.
26
Overtightening will damage the plastic mounting detail.
STEP 12: FINAL CHECKLIST (DOUBLE AND SINGLE MODELS)
Be sure product is level, securely fastened to the cabinetry and
opens and closes freely. The DishDrawer® must be free to close
with no resistance from the cabinetry.
TROUBLE SHOOTING
Excessive water remaining above the filter plate, after the
rinse cycle; check for kinked drain hoses or blocked waste
connection.
Be sure the inlet hose to valve connection is tightened a further half
turn after seal contact.
No water supply; check water is connected, ON and there is
the specified water pressure.
Be sure any knock-outs or plugs in drain connection have been
drilled out and drain connection has been made.
Turn ON the power and water supply. The DishDrawer® should
beep and light up.
DishDrawer® does not light up when the tub is opened;
be sure power is connected and is switched ON.
Open the drawer(s) and check operation of Wash Program Control
Panel and check the sprayarm(s) are in place and free to rotate.
Water around water supply and drainage connections -
check connections, existing plumbing and hoses for leaks.
On the Wash Program Control Panel select Rinse and close the
drawer(s). Start the program by pressing the Start/Pause button.
If a fault occurs, consult the Fault Code Section of the
User Guide.
After the Rinse program has finished, be sure the machine has run
and drained correctly.
If unable to resolve, contact your Customer Care Centre.
Check water supply and drainage connection for leakage.
Repeat for each Drawer.
LEAVE ALL LITERATURE WITH CUSTOMER.
STEP 13: CUSTOMER CARE
If you have any questions concerning the installation of this DishDrawer®,
please contact your Fisher & Paykel Authorized Service Agent.
FOR THE UNITED STATES OF AMERICA (USA) & CANADA
Fisher & Paykel Appliances
5900 Skylab Road
Huntington Beach
CA 92647
PHONE TOLL FREE 1888 9 FNP USA
1888 9 367 872
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|