Extron electronic TV Video Accessories DTP HDMI 330 User Manual

DTP HDMI 330 • Setup Guide  
This guide provides quick start instructions for an experienced installer to set up and operate the  
Extron DTP HDMI 330 digital video extender. The DTP HDMI 330 transmitter and receiver pair can  
extend an HDCP-compliant HDMI signal up to 330 feet (100 m).  
Installation  
Step 1 — Mounting  
Turn off or disconnect all equipment power sources and mount the Tx and Rx units as required.  
DTP HDMI 330 Tx Rear Panel  
DTP HDMI 330 Rx Rear Panel  
SIG  
LINK  
SIG  
LINK  
INPUTS  
POWER  
12V  
OVER DTP  
OUTPUTS  
POWER  
12V  
0.7A MAX  
AUDIO  
AUDIO  
RS-232  
IR  
L
R
0.7A MAX  
Tx Rx  
G
Tx Rx  
DTP OUT  
DTP IN  
7
2
1
4
3
7
4
5
6
Front Panel  
INPUTS  
Step 2 — Connections  
AUDIO  
OVER DTP  
RS-232  
IR  
HDMI Input connector (Tx) — Connect an HDMI  
cable between this port and the HDMI output port of  
the digital video source.  
a
Tx Rx  
G
Tx Rx  
DTP HDMI 330 Rx  
NOTE: See “LockIt™ Lacing Brackets“on the back of this guide for to securely  
3
fasten the input HDMI connector to the transmitter.  
Audio input (Tx) — Connect an unbalanced stereo audio source to this 3.5 mm mini  
stereo jack for an analog audio input.  
b
c
Connected RS-232  
and IR Device Pins  
Tx/Rx  
Pins  
RS-232 and IR connectors — To pass serial or infrared data or control signals, such as  
serial control of a projector, connect the master device to the transmitter and the slave  
device to the receiver via the RS-232 and IR captive screw connectors on both units.  
Transmit pin on connected unit  
Receive pin on connected unit  
Ground  
Transmit pin on connected unit  
Receive pin on connected unit  
DTP RJ-45 connectors — Connect transmitter DTP Out to receiver DTP In.  
Extron recommends that you terminate both cable ends in accordance with the  
following specifications, at a minimum:  
d
Pins:  
12345678  
TIA/EIA T  
568 B  
z
z
TIA/EIA T 568 B  
z
CAT 6A, shielded  
Pin Wire color  
24 AWG, solid conductor  
1
2
3
4
5
6
7
8
White-orange  
Orange  
ATTENTION: Do not connect these devices to a computer data  
White-green  
Blue  
or telecommunications network.  
White-blue  
Green  
Signal LED — Lights when the unit is receiving a clock signal on the HDMI input (for the transmitter)  
or any valid signal on the DTP In connector (for the receiver).  
White-brown  
Brown  
Link LED — Lights when a valid link is established between the units on the DTP cable.  
TP Wires  
HDMI Output connector (Rx) — Connect a display with an HDMI input for display of the  
transmitted direct digital image.  
e
f
OUTPUTS  
AUDIO  
R
L
NOTE: See the “LockIt™ Lacing Brackets“on the back of this guide for  
to securely fasten the output HDMI connector to the receiver.  
Audio Output connector (Rx) — Connect a balanced or unbalanced stereo or mono audio  
device to the receiver via the Audio captive screw connector. See the drawing below.  
No Ground Here  
Tip  
Ring  
Sleeves  
Tip  
Tip  
Sleeves  
Tip  
Ring  
Do not tin the wires!  
No Ground Here  
Unbalanced Stereo Output  
Balanced Stereo Output  
ATTENTION: Connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative (-) contacts.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Eureka Vacuum Cleaner 4670 Series User Manual
Fisher Paykel Oven OB24SDPX User Manual
Fisher Price Fitness Equipment K9125 User Manual
Foster Oven cod7138 000 User Manual
Fostex Computer Drive EX12 User Manual
FujiFilm Camcorder 16123567 User Manual
GE Mixer 106602 User Manual
Genesis Advanced Technologies Speaker Gen 928 User Manual
Gigabyte Computer Accessories GA 7VAC User Manual
Gigabyte Portable Speaker GP S5500 User Manual