Owner’s Manual
DVD-RAM drive unit with built-in HDD
Model EX12
Introduction
Thank you very much for purchasing the Fostex Model EX12.
The EX12 is a DVD-RAM drive unit dedicated to the PD-6. It in-
corporates a 12-cm DVD-RAM drive with a 2.5-inch HDD.
By connecting the EX12 to your PD-6, you can use two more drives
dedicated to the PD-6, in addition to the PD-6 internal DVD-RAM
drive.
Before using the EX12, read this manual carefully. We would be
very happy if the unit is helpful to you.
<Note>
To use the EX12, the PD-6 software version must be V2.00 or higher.
If the software version of your PD-6 is lower than V2.00, ask your
local Fostex dealer or sale office for upgrade.
The built-in HDD is formatted in the "Normal" mode when shipped.
This means, the HDD is divided into eight partitions, each of which
reserves approximately 4.7 GB capacity.
For details about how to use the EX12 with the PD-6, see "V2.0 supple-
ment" supplied with the PD-6.
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
•
Make sure that the voltage of your AC power outlet matches the voltage
requirements printed on the unit.
•
When disconnecting the AC cable, make sure that the unit [POWER] switch is
set to "OFF".
Disconnecting the AC cable while the power is "ON" may damage data
because the unit always transfers data between the current card and memory.
•
While the unit is accessing the DVD-RAM disk or internal HDD (for example,
during recording), never turn off the power. Make sure that the unit
completely stops accessing the disk before you turn off the power.
Otherwise, recorded data may be lost, as well as the DVD-RAM disk and
internal HDD may be damaged.
Note that Fostex assumes no responsibility on data loss or whatsoever due to use of
the unit.
•
•
Fostex is not responsible for any "direct damage" or "indirect damage" caused
by using the unit.
Do not let water or other liquid, or metal objects such as pins, accidentally
enter the inside of the unit (especially inside of the card slots) because this
may lead to electric shock or damage. Should water enter the inside of the
unit, turn off the power, unplug the AC cable, and consult your dealer or the
nearest FOSTEX service station.
•
Do not drop the unit or give it a strong shock. The internal circuits may be
damaged. Although the unit is designed to operate outside, handle the unit
with great care because it is a precision machine.
•
•
To prevent possible electric shock and damage to the unit, do not remove the
cover or reach the inside of the unit.
When using the supplied carrying belt, to prevent the unit from dropping
accidentally, make sure that it is attached to the unit correctly.
Precautions on installation
• Do not install the unit in the following conditions.
• in a extremely hot or cold place
• in a moist place
• in a shaky or unstable place
• in a dusty place
• in a strong magnetic field or near a device which generates a magnetic field
• in the direct sunshine
• in the direct rain or water
• Notes on moisture condensation
When you bring the unit from a cold place to a warm place, moisture may
condense on the drive, display, panels, etc. In such a case, leave the unit for a
while until it warms up and evaporates any moisture.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Names and functions
1
2
OPEN/CLOSE
POWER
ON
PD-6
HD
EX12 EXTERNAL DRIVE UNIT
IEEE1394/USB
OFF
6
8
7
5
4
3
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
AVIS:
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS EQUIPMENT
TO RAIN OR MOISTURE.
13
12 11
10
9
1) Fastenings
<Note>: While the EX12 is in operation (i.e. during
recording or playback using the EX12 HDD or DVD-
RAM drive, or while exporting or importing data),
do not switch the selector position, which may
cause malfunction.
The left and right fastenings are used to fasten the
EX12 and PD-6 when stacking them up. (See the next
page for details.)
2) Disk tray
You can set a DVD-RAM disk on the tray.
7) Power switch
Turns on or off the power of the unit.
3) [OPEN/CLOSE] key
Pressing this key opens or closes the disk tray.
Do not press this key while the disc is being accessed,
which may destroy the disc contents.
8) Cooling fan
9) [USB] port
Used to connect to a PC via USB.
4) Access indicator
Flashes while the DVD-RAM disk is being accessed.
10) [IEEE1394] ports
Two IEEE1394 connectors of different types are
provided. You can use either of the connectors
according to your PC.
5) [HD] indicator
Flashes while the built-in HDD is being accessed.
6) PD-6/IEEE1394 USB select switch
<Notes>: Never use the IEEE1394 and USB ports
simultaneously.
Also note that you cannot use the [USB] and
[IEEE1394] ports while the selector is set to
"PD-6".
Selects "PD-6" or "IEE1394 USB" according to the
situation.
Set the selector to this position when you
use the EX12 as a recording/playback
drive for the PD-6.
PD-6
11) [DC OUT (PD-6 ONLY)] connector
Used to connect to the [DC IN] connector of the PD-6
using the DC cord supplied with the EX12.
Set the selector to this position when ex-
porting a file recorded on a DVD-RAM
disk set on the EX12 to your PC.
IEEE1394
USB
12) [DC IN] connector
Used to connect to the external DC power supply.
13) [AC IN] connector
Used to connect to the supplied AC cord.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
4) Fix the supplied cushion using the fixing screws
which are removed in the previous step.
How to stack the PD-6 and EX12 together
1) Remove the blank panel at the bottom of the
PD-6.
Cushion
5) Pull out the connection cable from inside the
EX12.
2) Replace the two screws for fixing the rubber
feet at the bottom of the PD-6 with the screws
supplied with the EX12.
<Note>: Never forget to replace the screws
for fixing the rubber feet. Otherwise, the PD-
6 may malfunction or generate a noise be-
cause of imperfect grounding.
6) Put the PD-6 on the EX12 and plug the
connector of the cable to the PD-6, as shown
below. Make sure to plug the connector in the
correct direction.
3) Remove the two screws for fixing the cover at
the top of the PD-6, and open the cover.
<Note>: The removed screws are used later
for fixing the cushion. Be sure not to lose
them.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
After hanging the projection on the PD-6, lift
up the fixing angle until it is locked.
7) After connecting the cable, stack the PD-6 on
the EX12.
<Note>: When stacking the PD-6 on the EX12,
make sure to perfectly fit the dent of PD-6
rubber feet to the metallic projections of each
EX12. Otherwise, the PD-6 may malfunction
or generate a noise because of imperfect
grounding.
9) Fasten the fixing screw of each fastening.
Fasten the fixing screw of each fastening so that
the fastening may not be off. Be careful not to
apply excessive force.
8) Use the fastenings on both the left and right
Confirm both the left and right fastenings are
fixed tightly.
sides of the EX12 to fastening the PD-6.
Pull up the metallic projection of each fasten-
ing and hang it on the PD-6.(The following pic-
tures show the example of the left side.)
Now you complete stacking the EX12 and PD-6
together.
The next step is to connect the power cords.
See the next page.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the power cords
To supply power to the PD-6 and EX12, connect the AC and DC cords supplied with the
EX12, as shown below.
Make connection using the supplied DC cord.
This connector is used when using the external DC power supply.
Connect to the AC outlet using the supplied AC cord.
<Notes>
• When the EX12 is connected to the PD-6, turn on the EX12 first, followed by the PD-6.
• When the EX12 is connected to the PD-6, make sure that both the PD-6 and EX12 are turned
off before you switch the selector (for selecting [PD-6 IEEE1394] or [USB]) on the EX12 front
panel.
PC connection
By connecting the EX12 to your PC regardless of whether the EX12 is connected to the PD-
6 or not, you can export the EX12 audio file data to your PC. Read the following notes
carefully before making connection. See also the next page for the connection examples.
<Notes for using the EX12 with your PC>
To use the EX12 with your PC, install the dedicated driver (on the supplied CD-
ROM) or commercially available DVD-RAM writing software to your PC.
Also note that even if the dedicated driver (or commercially available DVD-RAM
writing software) is correctly installed, the Read/Write functions are limited de-
pending on OS, as below.
When using the [USB] port:
Windows XP, 2000
--> Both "Read" and "Write" are possible.
Macintosh OSX, OS9.2.1, OS9.2.2 --> Only "Read" is possible
When using the [IEEE1394] port:
Windows XP, 2000, ME, 98SE
--> Both "Read" and "Write" are possible.
Macintosh OSX, OS9.2.1, OS9.2.2 --> Only "Read" is possible.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the EX12 alone to your PC
By connecting the EX12 to your PC, you can export an audio file on a DVD-RAM disk set to
the EX12. Note that you cannot export an audio file on the EX12 internal HDD.
To the IEEE1394 or USB
port on your PC
<Notes for using>
• Set the selector on the EX12 front panel to "IEEE1394/USB".
• Connect the EX12 to your PC via the IEEE1394 or USB port. Never use both ports together.
Daisy-chaining the PD-6, EX12 and PC
By making "daisy chain" of the PD-6, EX12 and PC as shown below, you can export an audio
file on a DVD-RAM disk set to the PD-6 or EX12.
If your PC has more than one IEEE1394 port, you also can connect the PD-6 and EX12
individually to the IEEE1394 ports on the PC.
IEEE1394 port on the
PD-6
To the IEEE1394 port
on the PC
<Notes for using>
• When the EX12 is connected to the PD-6, make sure that both the PD-6 and EX12 are turned
off before you switch the selector (for selecting [PD-6 IEEE1394] or [USB]) on the EX12 front
panel.
• Set the "IEEE1394" menu item in the Utility mode of the PD-6 to "CONNECT".
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Main specifications
Internal drives:
USB port (for PC connection)
12-cm DVD-RAM drive and 2.5-inch HDD (40 GB)
Connector:
USB Series "B" receptacle
Pin assignment:
Inputs/Outputs:
DC12V IN
1: VBUS, 2: D- (DATA), 3: D+ (DATA),
4: GND
Connector:
Pin assignment:
XLR-4-32 type (male)
External dimensions:
386 (W) x 94 (H) x 231 (D) mm
1: GND, 2: NC, 3: NC, 4: +12~18 V
Power requirement/power consumption:
100~240 VAC, 38W
12VDC 3A
DC12V OUT (PD-6 ONLY)
Connector:
XLR-4-31 type (female)
Pin assignment:
1: GND, 2: NC, 3: NC, 4: +12~18 V
Weight
IEEE1394 port (for PC connection)
Approx. 4.3 kg
Connector:
1: FireWire 400 (4-pin)
2: FireWire 400 (6-pin)
Supplied accessories
Pin assignment (FireWire 400, 4-pin):
1: TPB-, 2: TPB+, 3: TPA-, 4: TPA+
Pin assignment (FireWire 400, 6-pin):
1: VP, 2: VG, 3: TPB-,
* A pair of rack mount adaptors x2
* AC cord x1
* DC cord (for connection to the PD-6) x1
* Cushion x 1
4: TPB+, 5: TPA-, 6: TPA+
* Fixing screws x2
* DVD-RAM disk x1
* DVD-RAM Driver Software (for windows) x1
DVD-RAM
DVD-RAM disk
Driver Software
AC connect cable
DC connect cable
Rack mount adaptor (x2)
Cushion
Fixing screw (x2)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of EC Directive
This equipment is compatible with the EMC Directive (89/336/EEC) - Directive on approximation of member nation's ordinance
concerning the electromagnetic compatibility and with the Low Voltage Directive (73/23/EEC) - Directive on approximation
of member nation's ordinance concerning electric equipment designed to be used within the specified voltage range.
The Affect of Immunity on This Equipment
The affect of the European Specification EN61000-6-1 (coexistence of electromagnetic waves - common
immunity specification) on this equipment are as shown below.
In the electrical fast transient/burst requirements, surge, conducted disturbances by radio-frequency fields, power frequency
magnetic field, radiate electromagnetic field requirements and static electricity discharging environment, this could be
affected by generation of noise in some cases.
FOSTEX DISTRIBUTORS LIST IN EUROPE
* Including non-EU countries (as of October, 2003)
<AUSTRIA>
<ITALY>
NAME: ATEC Audio-u. Videogeraete VertriebsgesmbH.
ADD: Im Winkel 5, A-2325 Velm, Austria
TEL: (+43) 2234-74004, FAX: (+43) 2234-74074
NAME: Proel S. p. A.
ADD: Zona Via Alla Ruenia, 37/43 64027 -Sant’Omero
(Teramo), Italy
TEL: (+39) 0861-81241, FAX: (+39) 0861-887862
<BELGIUM>
NAME: General Audio
<THE NETHERLANDS>
ADD: Albert Temmerstraat 21, 1731 Zellik, Belgium
TEL: (+32) 2-4630650, FAX: (+32) 2-4661500
NAME: IEMKE ROOS AUDIO B. V.
ADD: Kuiperbergweg 20, 1101 AG Amsterdam, The
Netherlands
<DENMARK>
TEL: (+31) 20-697-2121, FAX: (+31) 20-697-4201
NAME: SC Sound ApS
<NORWAY>
NAME: Fitzpatrick
ADD: Malervej 2, DK-2630 Taastrup, Denmark
TEL: (+45) 4399-8877, FAX: (+45) 4399-8077
ADD: P. B. 4316 Nydalen, 0402 Oslo, Norway
TEL: (+47) 23 400 380, FAX: (+47) 23 400 389
<FINLAND>
NAME: Noretron Oy Audio
<PORTUGAL>
ADD: P. O. Box 22, FIN-02631 Espoo, Finland
TEL: (+358) 9-5259330, FAX: (+358) 9-52593352
NAME: Caius - Tecnologias Audio e Musica, Lda.
ADD: Praca do Bom Sucesso, No 61 Bom Sucesso Trade
Center, Escritorio 701/702, 4150 - 146 Porto, Portugal
TEL: (+351) 22-608-06-10, FAX: (+351) 22-608-06-29
<FRANCE>
NAME: Sennheiser France
ADD: 128 bis, avenue Jean-Jaures, 94851 Ivry-sur-Seine
Cedex, France
<SPAIN>
TEL: (+33) 1 4987 0300, FAX: (+33) 1 4987 0324
NAME: Letusa S. A.
ADD: C/Laguna 10, 28923 Alcorcon, Madrid, Spain
TEL: (+34) 91-4862800, FAX: (+34) 91-6414597
<GERMANY>
NAME: Mega Audio GmbH
<SWEDEN>
NAME: TTS Scandinavia AB
ADD: Stromberger Str. 32, D-55411 Bingen, Germany
TEL: (+49) 6721-94330, FAX: (+49) 6721-32046
ADD: Kavallerivagen 24, 172 48 Sundbyberg, Sweden
TEL: (+46) 8-59798000, FAX: (+46) 8-59798001
<GREECE>
NAME: Bon Studio S. A.
<SWITZERLAND>
NAME: Audio Bauer Pro AG
ADD: Bernerstrasse-Nord 182, CH-8064 Zurich,
Switzerland
ADD: 6 Zaimi Street, Exarchia, 106.83 Athens, Greece
TEL: (+30) 210-3809-605, 606, 607, 608
FAX: (+30) 210-3845-755, 210-3827-868
<ICELAND>
TEL: (+41) 1-4323230, FAX: (+41) 1-4326558
NAME: I. D. elrf. electronic Ltd.
ADD: ARMULA 38 108 REYKJAVIK, ICELAND
TEL: (+354) 588 5010, FAX: (+354) 588 5011
<UK>
NAME: SCV London
ADD: 40 Chigwell Lane, Oakwood Hill Industrial Estate,
Loughton, Essex IG10 3NY U. K.
TEL: (+44) 20-8418-0778, FAX: (+44) 20-8418-0624
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|