Extron electronic Stereo Receiver FOX 500 DVI Rx User Manual |
Specifications — FOX 500 DVI Series
The FOX 500 DVI consists of a transmitter (FOX 500 DVI Tx) and a receiver (FOX 500 DVI Rx)
with one or two fiber optic cables linking the two units. They are available in singlemode or
multimode versions.
N
The analog audio signal(s) is (are) digitized in the transmitter, sent through the fiber cable, and
converted back to analog audio in the receiver.
These transceivers are class 1 laser products. They meet the safety regulations of IEC-60825,
FDA 21, CFR 1040.10, and FDA 21 CFR 1040.11.
N
N
Optical fiber interconnection between transmitter and receiver
Number/type �������������������������������� 1 or 2 fiber optic
Only one fiber is required to transmit video, audio, and unidirectional data. A second fiber is
required to transmit return data for bidirectional control/communication.
N
Connectors ������������������������������������� 2 LC connectors
Operating distance
Singlemode������������������������� 30 km (18�75 miles) with singlemode (SM) cables with a FOX 500 DVI SM
Multimode�������������������������� 300 m (985') with 62�5 µm multimode (MM) cables with a FOX 500 DVI MM
1 km (3280') with 50 µm multimode (MM) cables with a FOX 500 DVI MM
2 km (6561') with 50 µm 2000 MHz bandwidth laser optimized multimode
cable with a FOX 500 DVI MM
Operating distance is approximate. These are typical maximum distances that may vary depending
on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic
dispersion, environmental factors, and kinks.
N
Nominal peak wavelength����������� 850 nm for FOX 500 DVI MM, 1310 nm for FOX 500 DVI SM
Data rate ����������������������������������������� 4�25 Gbps
Transmission power
Singlemode������������������������� -5 dBm, typical
Multimode�������������������������� -5 dBm, typical
Maximum receiver sensitivity
Singlemode������������������������� -18 dBm, typical
Multimode�������������������������� -12 dBm, typical
Optical loss budget
Singlemode������������������������� 13 dB, maximum
Multimode�������������������������� 7 dB, maximum
Video
Resolution range ��������������������������� Single link DVI and HDMI digital video signals are supported, including
640x480 @ 60 Hz through 1600x1200 @ 60 Hz, and also HDTV signals at
480p, 720p, 1080i, and 1080p�
Higher resolutions up to 1920x1200 @ 60 Hz, undersampled
*Appropriate DVI-D to HDMI cables or adapters are required for HDMI signal input/output.
The FOX 500 DVI Series can be used to distribute HDMI signals if you use a DVI-to-HDMI
adapter. However, when using HDMI signals, the FOX units do not transmit audio and CEC
signals.
N
N
Formats������������������������������������������� RGB and YCbCr digital video
Standards���������������������������������������� DVI 1�0, HDMI 1�2
Video input and loop-through — transmitter (FOX 500 DVI Tx)
Number/signal type��������������������� 1 DVI-D (or HDMI*) input
1 DVI-D (or HDMI*) loop-through
Connectors ������������������������������������� 1 female DVI-I for input
1 female DVI-I for loop-through
Nominal level �������������������������������� 0�8 Vp-p
Impedance�������������������������������������� 100 ohms
Extron FOX 500 DVI Tx, FOX 500 DVI Rx Fiber Optic Transmitter-Receiver Pair • Specifications
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial control pin configurations� Captive screw connectors: 1 = Tx, 2 = Rx, 3 = GND
Mini stereo jack: tip = Tx, ring = Rx, sleeve = GND
Program control����������������������������� Extron’s control/configuration program for Windows®
Extron’s Simple Instruction Set (SIS™)
General
Power���������������������������������������������� 100 VAC to 240 VAC, 50-60 Hz, 11 watts, internal
Temperature/humidity���������������� Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling ������������������������������������������� Convection, vented left to right, vents on side panels
Mounting
Rack mount������������������������ Yes, with optional rack shelf kit
Furniture mounting holes Yes, with optional under desk mounting kit
Enclosure type ������������������������������� Metal
Enclosure dimensions������������������� 1�7" H x 8�7" W x 9�5" D (1U high, half rack wide)
(4�3 cm H x 22�1 cm W x 24�1 cm D)
(Depth excludes connectors and knobs�)
Product weight ������������������������������ 2�3 lbs (1�0 kg) per unit
Shipping weight ���������������������������� 4 lbs (2 kg) per unit
Vibration����������������������������������������� ISTA 1A in carton (International Safe Transit Association)
Regulatory compliance
Safety����������������������������������� CE, CUL, FDA Class 1, UL
EMI/EMC �������������������������� CE, C-tick, FCC Class A, ICES, VCCI
MTBF����������������������������������������������� 30,000 hours
Warranty����������������������������������������� 3 years parts and labor
All nominal levels are at 10%.
Specifications are subject to change without notice.
N
N
7.6-031709-D6
Extron FOX 500 DVI Tx, FOX 500 DVI Rx Fiber Optic Transmitter-Receiver Pair • Specifications
3
Download from Www.Somanuals.com. All Manuals Search And Download.
|