Models
1104HB
1104HG
1104HP
1104HV
1104HW
1 Year Limited Warranty
This warranty applies to defects resulting from imperfections in manufacture of
parts entering into the manufacture and assembly of the sewing machine which this
warranty accompanies, for a period of one (1) year, subject to the following
conditions, exclusions and exceptions.
OWNER’S MANUAL
Models: 1104HB – 1104HG – 1104HP – 1104HV – 1104HW
This warranty is enforceable if said sewing machine is given reasonably good care
and proper maintenance in accordance with the accompanying printed instructions.
Needles, lamp bulb, and bobbins which normally require replacement are not
covered under this warranty.
Your exclusive remedy for any losses or damages resulting from defects in both
performance, workmanship and materials of this product shall be the repair or
replacement of this product.
The manufacturer shall not be liable for consequential or incidental damages for
breach of any express or implied warranty of this product.
This warranty is extended only to the original purchaser of the machine and this
warranty excludes all other legal and/or conventional warranties. The only
responsibility of EURO-PRO Operating LLC, if any, is in relation to the specific
obligations expressly assumed by it under the terms of this warranty bond.
Please include proof of purchase. For repairs or replacement, send to:
EURO-PRO Operating LLC, 4400 bois Franc, St. Laurent, Qc H4S 1A7, Tel.: (800) 361-4639
------------------------------------------------------------------------------------------------------------------------------
OWNERSHIP REGISTRATION CARD
Please fill out and mail the product registration card within ten (10) days of purchase. The
registration will enable us to contact you in the unlikely event of a product safety notification.
By returning this card you acknowledge to have read and understood the instructions for use,
and warnings set forth in the accompanying instructions.
Models: 1104HB – 1104HG – 1104HP – 1104HV – 1104HW
_________________________________________________________________________
Appliance model
_________________________________________________________________________
Date purchased
Name of store
_________________________________________________________________________
Owner’s name
_________________________________________________________________________
Address
City
State
Zip Code
EURO-PRO Operating LLC
4400 bois Franc,
St. Laurent Qc H4S 1A7
Tel.: 1 (800) 361-4639
EURO-PRO Operating LLC – All rights reserved
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
NEEDLE REPLACEMENT
NAME OF PARTS
Caution: Remove the batteries and/or
disconnect the AC/DC adapter before starting
to replace the needle.
1. Turn the hand wheel to raise the needle to
its highest position.
2. Hold the old needle and loosen the needle
clamp screw. Remove the old needle and
discard responsibly.
3. Insert the new needle into the clamp with
the flat side toward the right. Be sure to
push the needle all the way up into the
needle clamp before tightening the needle
clamp screw.
4. Tighten the needle clamp screw.
SEWING SLEEVES
This sewing machine has been designed to
sew sleeves or any narrow openings in
garments.
1. Lift the presser foot.
2. Position the garment over the sewing arm
and between the platform and the base.
3. Lower the presser foot and follow the
regular sewing instructions.
CAUTION:
1. Don’t press the On/Off button at the same time as the foot control.
2. Don’t use the batteries and the AC/DC adapter at the same time.
3. Make sure that the batteries are inserted in the correct position.
4. Don’t keep the machine running for too long.
5. Sewing some very stretchy fabrics might result in skipping stitches – use a stretch
needle.
6. It is not recommended for use on sewing fabrics such as terrycloth.
7. Use AC/DC adapter (6V, 1A) or 4 AA alkaline batteries (1.5 V) only.
9
2
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
BOBBIN WINDING
Bobbins (x2),
Thread Spools (x2), Needle,
Needle Threader
Foot Pedal
AC/DC Adapter
BATTERY INSTALLATION
Needle Bar
1. Battery compartment is on the bottom of the
sewing machine.
2. Open the cover of the battery compartment and
insert the 4 “AA” alkaline batteries. Make sure
that the batteries are in the correct position as
marked on the inside of the battery compartment.
3. Replace the battery compartment cover.
Caution: Make sure that the On/Off Button is in the
“Off” position when inserting or changing the
batteries. If the On/Off button is in the “On” position
when inserting or changing the batteries, the sewing
machine may run suddenly.
THREADING UPPER THREAD
Caution: When threading the
sewing machine, make sure that
the On/Off button is in the “Off”
position.
⑥
②
1. Place the spool of thread into
the spool pin.
2. Thread the machine following
this sequence: ①, ②, ③, ④, ⑤,
⑥, ⑦, ⑧, k.
①
Thread Clamper
④
To wind your bobbins:
③
1. Press on the bobbin winder lever to raise the bobbin winding pin.
2. Place an empty bobbin on the bobbin winding pin.
⑤
⑦
3. Place a spool of thread on the spool pin spindle.
⑧
4. Take the end of the thread from the thread spool and wind it counter clockwise
around the upper section of the thread clamper following the numbered sequence
in the illustration above.
⑨
5. Continue taking the thread around the needle bar.
6. Wrap the thread counter clockwise around the empty bobbin several times.
7. Press the bobbin winder button and run until the bobbin is full.
8. When the bobbin is full, release the bobbin winder button and remove the bobbin
from the bobbin winding pin.
9. Lift the bobbin winding lever to lower the bobbin winding pin.
3
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TENSION ADJUSTMENT
REPLACING THE BOBBIN
Caution: Never adjust the thread tension while sewing.
Caution: When replacing or inserting the bobbin,
make sure that the On/Off button is in the “Off”
position.
1. Press the bobbin cover release button and
remove the bobbin cover.
A correctly adjusted seam has the upper and the lower threads even and the junction
in the middle of the fabric. (See illustration below.)
2. Insert the new bobbin into the compartment
leaving a 3-inch tail.
3. Hold the end of the upper thread with your
right hand and turn the hand wheel slowly
counter clockwise until the needle goes down
and up again to its highest position. Pull the
upper thread slowly and the lower thread will
come up in a loop. Pull up both threads to
the back and place them together under the
presser foot.
1. If the upper thread (visible on the top of
the fabric) becomes a straight line, turn
the thread tension dial, counter clockwise
to obtain a balanced stitch. (See
illustration below.)
4. Replace the bobbin cover.
2. If the lower thread (visible on the
underside of the fabric) becomes a
straight line, turn the thread tension dial,
clockwise to obtain a balanced stitch. (See
illustration below.)
SETTING THE SEWING SPEED
This sewing machine has two (2) sewing speeds.
To adjust the sewing speed, press the speed
button. When the button is depressed, it is on the
faster speed. When the button is up, this is the
lower speed.
High speed
Low speed
7
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SEWING
STITCH LENGTH ADJUSTMENT & REVERSE SEWING
1. Turn the hand wheel to raise up the
needle to the highest position. Lift the
presser foot and place the fabric to be
sewn under the presser foot. (Fig. 1)
2. Lower the presser foot. (Fig. 2)
3. Press the On/Off button to the “On”
position and begin sewing. Do not
pull the fabric. Gently guide the fabric
to keep the seam straight. (Fig. 3)
4. After finishing sewing, press the
On/Off button to the “Off” position to
stop sewing. (Fig. 3)
5. Turn the hand wheel to raise the
needle to the highest position. Lift the
presser foot and gently remove the
fabric away from the sewing machine.
(Fig. 4)
0
0
Fig. 1
6. Cut the thread using the thread cutter.
(Fig. 5)
Regular Sewing
Reverse Sewing
Fig. 4
Before sewing your garment, test for the correct stitch length using a piece of fabric.
You can select from three different (3) stitch lengths for sewing and three (3) for
reverse sewing. To select the stitch length:
1. Turn the stitch length adjustment dial all the way to the left for the longest stitch
length. This is recommended for normal sewing.
2. As you turn the dial to the right, you decrease the length of the stitch until you get
to the center point which is “0” length. The needle will remain stationary if you set
the dial at this point.
Fig. 2
Fig. 3
3. As you continue to turn the dial to the right, you will now set the sewing machine
into reverse sewing. Again, you have three (3) different stitch lengths for reverse
sewing, the farthest to the right being the longest.
4. Use reverse sewing to secure your stitches at the beginning of your seam and at
the end. This will strengthen your seams.
Caution: Do not sew at “0” stitch length as this will cause your machine to get stuck.
Fig. 5
WORK LIGHT
If additional light is needed, press the light
switch to turn the light “On”. Press the switch
again to turn it “Off”.
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|