PRESSURE WASHER
OWNER'S MANUAL
Model VPW49HA
120V., 60 Hz., 13 Amps.
EURO-PRO Operating LLC
U.S.: 94 Main Mill Street, Door 16
Plattsburgh, NY 12901
Canada: 4400 Bois-Franc
St-Laurent, QC H4S 1A7
Tel.: 1 (800) 798-7398
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
SAFETY & WARNING INSTRUCTIONS
•
•
•
NEVER store the pressure washer outdoors
or where it could freeze. The pump will be
seriously damaged.
PROBLEM
PRESSURE
WASHER WILL
NOT START WHEN
THE ON/OFF
SWITCH IS IN THE
"ON" POSITION
POSSIBLE REASON
POSSIBLE SOLUTION
WARNING
1. Check plug, socket, fuses,
breaker.
Do not use pressure that exceeds the
operating pressure of any of the parts (hoses,
fittings, etc.) in the pressurized system.
Ensure that all equipment and accessories are
rated to withstand the maximum working
pressure of the unit.
Release trigger when changing from high to
low pressure modes. Failure to do so could
result to damage to the nozzle.
This unit must always be used in the
horizontal position.
1. Electrical socket is faulty or
breaker has tripped.
2. Check that the voltage is
adequate.
2. Voltage is inadequate.
3. GFCI has tripped.
3. Reset/Try another electrical
outlet.
4. Plug in power cord.
4. Power cord is not plugged in.
CAUTION
WARNING
1. Remove and clean water
intake filter.
Keep hose away from sharp objects. Bursting
hose may cause injury. Examine hoses
regularly and replace if damaged. Do not
attempt to mend a damaged hose.
Explosion hazard.
PUMP DOESN'T
REACH
ADEQUATE
PRESSURE OR
CAVITATES
1. Water intake filter is clogged.
2. Pump is drawing air.
3. Diameter of garden hose is
too small.
2. Tighten connections/bleed
system.
•
NEVER spray flammable liquids or use
pressure washer in areas containing
combustible dust, liquids or vapors.
NEVER operate this machine in a closed
building or in or near an explosive
environment.
3. Replace with 3/4 inch
garden hose.
4. Check hose for kinks or
leaks, open tap fully.
4. Water supply is restricted.
•
EXTENSION CORDS
DANGER
1. Turn unit and water supply
off/Bleed system/Hold
trigger down. Allow water to
flow through the pump for
30 seconds.
WARNING
If using an extension cord, use only grounded,
three wire extension cords that are in good
condition. Use only extension cords that are
intended for outdoor use. These extension
cords are identified by a marking "Acceptable
for use with outdoor appliances; store indoors
while not in use." Use only extension cords
having an electrical rating not less than the
product. Do not use damaged extension
cords. Examine extension cord before using
and replace if damaged. Do not abuse
extension cord and do not pull on the cord to
disconnect. Keep cord away from heat and
sharp edges. Always disconnect from the
receptacle before disconnecting the product
from the extension cord.
PRESSURE
WASHER HAS OR
WILL NOT
1. Excessive air in waterline and
pump.
Do not spray electrical apparatus or wiring.
•
NEVER disconnect the high pressure
discharge hose from the machine while
the system is pressurized. To depressurize
the machine, turn the power and water
supply off, then press the gun trigger 2-3
times.
NEVER permanently engage the trigger
mechanism on the gun.
NEVER operate the machine without all
the components properly connected to
the unit (handle, gun/lance assembly,
nozzle, etc.).
MAINTAIN
2. Water supply is restricted.
PRESSURE
2. Check hose for kinks or
leaks, open tap fully.
PRESSURE
WASHER MAKES
EXCESSIVE NOISE
1. Air intake is blocked.
2. Water intake filter is dirty.
1. Clean the air intake vents.
2. Check & clean filter.
•
•
MOTOR DOES
NOT RUN
CONTINUOUSLY
WHEN TRIGGER IS
SQUEEZED/
MOTOR BUZZES
WHEN TURNED
ON BUT DOES
NOT
START/MOTOR
STOPS RUNNING
WHILE UNIT IS IN
USE
WARNING
Note: Do not use 16 or 18 AWG extension
cords on this product.
1. Net voltage is lower than
suggested.
1. Check that the voltage is
adequate.
Equipment damage.
•
•
•
ALWAYS turn water supply "ON" before
turning the pressure washer "ON". Running
pump dry causes serious damage.
Do not operate the pressure washer with
the inlet water screen removed. Keep
screen clear of debris and sediment.
NEVER operate pressure washer with
broken or missing parts. Check equipment
regularly and repair or replace worn or
damaged parts immediately.
DANGER
Failure to follow these instructions can result
in serious injury, including death.
WARNING
To reduce the risk of electrocution, keep all
connections dry and off the ground. Do not
touch the plug with wet hands.
•
•
•
Use only the nozzle supplied with this
machine.
Never leave the lance unattended while
the machine is running.
Never attempt to alter factory settings.
Altering factory settings could damage the
unit and will void the warranty.
Always hold gun and lance firmly when
starting and operating the machine.
NEVER allow the unit to run with the
trigger released (OFF) for more than one
minute. Resulting heat buildup will
damage pump.
Allowable Length
Extension Cord
25 '
50 ’
14 AWG
12 AWG
YES
NO
•
•
YES
YES
9
2
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING TO KNOW YOUR PRESSURE WASHER
OPERATING INSTRUCTIONS
Maintenance & Cleaning
Winterizing & Long Term Storage
1. Disconnect all water connections.
2. Turn the pressure washer on for a few
seconds, until any remaining water in
the pump exits.
Lubrication: The pressure washer is
supplied with a closed lubrication system,
so no addition of oil is needed.
1. Water Intake
2. Pressure Washer
3. Handle
4. Power Cord
5. Wheel Locks (x2)
6. Wheels (x2)
Checking the Water Intake Filter: The
water intake filter is located inside the
water intake connector. (Fig. 18) Remove
periodically and inspect for any deposits
that might accumulate there.
3. Turn the unit off immediately.
4. Store the pressure washer, parts and
accessories in an area with a temperature
above 32°F.
7. Trigger Lock
Motor Thermostat
8. Trigger
9. High Pressure
Hose Connector
Important: This pressure washer is
equipped with a motor thermostat. The
motor will stop if it is overheating. Wait 10-
20 minutes before starting the unit again. If
it stops again, please call customer service
at 1 (800) 798-7398.
Hose Connector
Water Intake
Fig. 18
10. Trigger Gun
11. Adjustable Lance
12. High Pressure Hose
13. On/Off Switch
14. High Pressure Output
15. Soap Dispenser (x3)
16. Brush
17. Hose Connector
18. Garden Hose Coupling
19. Water Intake Filter
Cleaning the Nozzles: If you notice that the
output pressure fluctuates, you may have to
clean the nozzles. Turn the unit "Off".
Unplug from electric outlet and disconnect
the water supply. Remove the lance, trigger
gun and hose from unit. Take the small
metal pin provided and insert into the nozzle
end to remove any obstructions. (Fig. 19)
Ground Fault Circuit Interrupter
(GFCI)
This unit is equipped with a Ground Fault
Circuit Interrupter (GFCI) built into the
plug. This device provides additional
protection from the risk of electrical shock.
When connecting the GFCI to the electrical
outlet, the indicator should appear red. If the
indicator is not red, depress the RESET
button on the GFCI until the indicator
appears red.
Fig. 19
This will occur more frequently if your
water supply is very hard.
Cleaning Tips
Wood Decks: Rinse deck and surrounding
area with fresh water. If using detergent, fill
the detergent applicator bottle and apply to
the area being cleaned. For optimal results,
reduce your work area to small sections and
clean each section one at a time. Allow the
detergent to rest on the surface for a few
minutes and then rinse at high pressure. Do
not let the detergent dry on the deck.
Always clean from left to right and top to
bottom for best results. Rinse at high
pressure using the fan jet keeping the tip of
the spray nozzle 8-12 inches from the
surface. Caution: For soft woods, increase
the distance from the cleaning surface.
Cars, Boats, & Motorcycles: Wet down area
to be cleaned before applying detergent
with clean water. Fill the detergent
Storing Your Pressure Washer
When you have finished using your
pressure washer, follow these steps for
safe storage:
1. Turn the pressure washer to the "Off"
position.
2. Turn off the water supply.
3. Before disconnecting the high pressure
hose connection, point the trigger gun
in a safe direction away from you and
discharge the high pressure water.
Disconnect the high pressure hose
from the pressure washer and trigger
gun.
4. Disconnect the garden hose from
pressure washer.
*Illustrations may differ from actual product.
Technical Specifications
applicator bottle and apply to the area being
cleaned. To achieve best results, clean one
side at a time. Allow the detergent to rest on
the surface for a few minutes but do not let
it dry. Rinse at high pressure using the fan
jet in a sweeping motion keeping the tip of
the spray nozzle at least 8-10 inches away
from the surface. Maintain a further distance
when using a direct spray. Wipe surface for
a polished finish.
5. Remove excess water from the pump
by tipping the unit on both sides to
drain any remaining water from the
water intake and outlet fittings.
6. Wipe away any remaining water on all
parts and fittings.
Voltage:
Power:
Pressure:
120V., 60Hz.
13 Amps
1900 psi. (max)
7. Engage the trigger gun safety lock.
8. Store the unit and accessories in a
room above 32°F.
3
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Suitable Use of Your Pressure
Washer
Unpacking Your Pressure Washer
Using Brush With the Trigger Gun
CAUTION
After you open the package, check to
make sure that all the parts are in the box
as per parts that are illustrated on page 3
of this guide. Due to transport and
packing restraints, some accessories
may be supplied unassembled; in this
case follow the assembly instructions in
this manual. If you have any questions,
call Euro-Pro Operating LLC customer
service at 1 (800) 798-7398. Keep all
small and potentially harmful parts of the
packaging (plastic bags, foamed
The brush is used with the trigger gun.
Push the brush onto the trigger gun
nozzle and turn clockwise to lock as
you would for the lance. (Fig. 15) The
brush may be used for washing cars,
boats, windows and other similar items.
The brush operates at open orifice
pressure so it will not direct a stream of
water.
This high pressure washer is suitable for
non-professional use. The working
temperature must range between 40°F
and 120°F. The machine is supplied with
a trigger gun, equipped with a trigger
handle to offer a comfortable working
position.
The high pressure washer is suitable for
washing with cold water only. The water
that you use for the pressure washer
must not be dirty, sandy or contain any
corrosive chemical products.
The pressure washer may be used to
wash shutters, doors, tiles, cars, decks,
campers, etc., where high water pressure
is necessary to remove dirt.
With the soap dispenser, the pressure
washer can be used to apply a thick
coating of aerated detergent to the areas
being cleaned .
When you wish to stop using the
pressure washer temporarily, make sure
that the trigger lock has been engaged to
avoid any accidental operation. (Fig. 12)
Trigger
Lock
Fig. 12
Using the Adjustable Lance
The angle of the water on the adjustable
lance may be adjusted between 0° and
60° by turning the nozzle adjuster
polystyrene, nails, etc.) out of the reach
of children.
Fig. 15
Correct Use of the Pressure
Washer
counter-clockwise for a wider angle or
clockwise for a narrower angle. (Fig. 13 &
Fig. 14) Always make sure that the
"On/Off' switch is in the "Off" position
before changing the angle of the water
jet. It is also recommended that the
trigger gun safety lock be engaged as
well. The adjustable lance allows you to
use any variety of spray pattern from a
full fan spray to a direct stream spray.
When using the pressure washer to clean
wood decks, siding, vehicles, etc., always
start using the fan spray and begin
spraying from a minimum 36" away to
avoid damaging the surface of the
material that you are cleaning. Always
clear the area that you will be cleaning; of
people, pets and objects.
Using Detergent with the Pressure
Washer
The soap dispenser may only be used
with the trigger gun.
Add detergent to the bottle and then
attach the soap dispenser to the
adjustable lance, just push it firmly onto
the end of the trigger gun until it snaps
into place. (Fig. 16)
• Place the pressure washer in a safe
area and on a horizontal surface.
• When using the pressure washer,
hold the trigger gun firmly with one
hand on the handle and the other on
the lance. (Fig. 1)
When using the pressure washer we
recommend the use of personal safety
items to reduce the risk of accidental
injury.
Fig. 1
Fig. 16
• NEVER point the water jet at electric
wiring, at the pump unit, or at any
person or animal.
To remove the soap dispenser, lift the
tab on the top of the connector and pull
off. (Fig. 17)
Fig. 13
Counter-clockwise
Fig. 14
Clockwise
Fig. 17
7
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling the Pressure Washer
OPERATING INSTRUCTIONS
Attaching High Pressure Hose to
Pressure Washer
Garden Hose Connection
Attaching The Wheels To The
Pressure Washer
Once all the desired attachments and
the high pressure hose are attached to
the pressure washer, you can connect
the garden hose to the unit.
1. Make sure that the water intake filter
is inside the water intake inlet.
(Fig. 11)
2. Attach the male adapter (supplied)
to the water intake connector on the
front side of the unit. (Fig. 11)
3. Attach the female hose coupling to
the garden hose. (Fig. 11)
4. Connect the female hose coupling
to the male adapter making sure
that it is tightly secured in place.
(Fig. 11)
Once the pressure washer is assembled,
you are ready to use the unit.
1. While facing the rear of the unit attach
the high pressure hose to the high
pressure output connector on the back
side of the unit. Twist on tight to avoid
leakage. (Fig. 8)
1. Carefully take all the parts out of the
packaging container and place
together on a flat, stable surface.
2. Insert the wheels onto the wheel
axle and push in the wheel lock to
lock the wheels in place. (Fig. 2)
3. Turn the pressure washer upside
down and slide the front support
onto the unit. (Fig 2)
4. Using the 1” long nickel plated
screw, secure the front support to
the unit.
Wheel
Fig. 8
Wheel
Lock
2. Then attach the other end of the high
pressure hose to the high pressure
hose connector on the trigger gun.
(Fig. 9)
Water inlet
Screw,
1” long,
nickel plate
Water intake
filter
Wheel
Axle
Front
Support
Garden hose
(not supplied)
Fig. 2
Attaching The Handle To The
Pressure Washer
Fig. 9
Fig. 11
1. Place the handle on the unit as
shown in Fig. 3.
2. Push the handle in at the bottom
until it is in position. (Fig. 4)
3. Let the handle slide down to its
resting place as shown in Fig 5 & 6.
4. To secure the handle to the unit,
screw 1 1/4” screw at the top hole
and the two (2) 7/8” screws on each
side of the handle. (Fig. 7)
3. Once the high pressure hose is
connected to the trigger gun, you can
attach the lance and accessories that
you desire. To attach either the
lance or the brush to the trigger gun,
hold the trigger gun in your left hand
insert the lance or the brush and
push it in all the way into the
connector on the trigger gun and turn
it clockwise 60° until it locks in place.
To remove the attachment, push
down on the attachment and turn
counter-clockwise 60° and then pull
out. Make sure that the attachments
are securely locked in place before
use. (Fig. 10)
Garden hose
coupling
Hose
connector
5. After all the connections have been
made and BEFORE you plug the
pressure washer into an electrical
outlet, open the water supply and
press on the trigger switch in order to
remove any air which may be in the
hose or pump. Continue to press on
the trigger switch until you get a
constant flow of water coming out of
the trigger gun. Allow water to flow
for 30 seconds.
Fig. 3
Fig. 4
1 1/4”
SCREW
7/8”
SCREW
7/8”
SCREW
6. Once this is accomplished, stop
pressing the trigger switch. Engage
the safety lock on the trigger.
7. Ensure that the "On/Off" switch, at
the side of the unit, is on the "Off"
position, then plug the unit into an
electrical outlet and turn the unit to
the "On" position.
8. Now you are ready to use the
pressure washer. Disengage the
safety lock and depress the trigger on
the trigger gun.
Fig. 5
Fig. 10
Fig. 7
Fig. 6
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|