MULTIMEDIA PROJECTOR
MODEL LC-SD12
OWNER’S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
31
TRADEMARKS
• Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
• IBM, VGA, XGA, and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
• Windows and PowerPoint are registered trademarks of Microsoft Corporation.
• Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its respective
corporation.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
To the Owner
Before operating this projector, read this manual thoroughly to
operate the projector properly.
Safety Precaution
This projector provides many convenient features and
functions. Operating the projector properly enables you to
manage those features and maintains it in better condition for
a considerable time.
Improper operation may result in not only shortening the
product-life, but also malfunctions, a fire hazard, or other
accidents.
If your projector seems to operate improperly, read this
manual again, check operations and cable connections and try
the solutions in the “Troubleshooting” section at the end of
this booklet. If the problem still persists, contact the sales
dealer where you purchased the projector or the service
center.
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
– This projector produces intense light from the projection
lens. Do not stare directly into the lens as possible. Eye
damage could result. Be especially careful that children do
not stare directly into the beam.
– Install the projector in a proper position. If not, it may
result in a fire hazard.
– Take appropriate space on the top, sides and rear of the
projector cabinet for allowing air circulation and cooling the
projector. Minimum distance should be taken. If the
projector is to be built into a compartment or similarly
enclosed, the minimum distances must be maintained. Do
not cover the ventilation slot on the projector. Heat build-
up can reduce the service life of your projector, and can
also be dangerous.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE EXCEPT LAMP REPLACEMENT.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
SIDE and TOP
REAR
0.7'(20cm)
3'(1m)
1.5'(50cm)
1.5'(50cm)
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
– Do not put any flammable object or spray can near the
projector, hot air is exhausted from the ventilation holes.
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE OWNER'S MANUAL WITH
THIS UNIT.
– If the projector is not to be used for an extended time,
unplug the projector from the power outlet.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER
USE.
CAUTION
Not for use in a computer room as defined in the Standard for
the Protection of Electronic Computer/Data Processing
Equipment, ANSI/NFPA 75.
Ne peut être utilisé dans une salle d’ordinateurs telle que
définie dans la norme ANSI/NFPA 75 Standard for Protection
of Electronic Computer/Data Processing Equipment
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
All the safety and operating instructions should be read before
the product is operated.
This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest
on the power cord. Do not locate this projector where the
cord may be damaged by persons walking on it.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.
Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
Do not expose this unit to rain or use near water, for example,
in a wet basement, near a swimming pool, etc..
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been
damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.
An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector,
ask the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
Voor de klanten in Nederland
Bij dit produkt zijn batterijen
geleverd.
Wanneer deze leeg zijn, moet u
ze niet weggooien maar
inleveren als KCA.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
Do not install the projector near the ventilation duct of air-
conditioning equipment.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instruction
Air Circulation
Installing the Projector in Proper Position
Install the projector properly. Improper Installation may reduce
the lamp lifetime and cause a fire hazard.
Openings in the cabinet are provided for ventilation and to
ensure reliable operation of the product and to protect it from
overheating, and these openings must not be blocked or
covered.
20˚
Do not tilt the projector more than 20
CAUTION
degrees above and below.
20˚
Hot air is exhausted from the exhaust vent. When using or
installing the projector, the following precautions should be
taken.
– Do not put any flammable objects near the vent.
– Keep the exhaust vent at least 3’(1m) away from any
objects.
Do not point the projector up to pro-
ject an image.
– Do not touch a peripheral part of the exhaust vent, espe-
cially screws and metallic part. This area will become hot
while the projector is being used.
NO UPWARD
– Do not put anything on the cabinet. The materials put on
the cabinet will not only get damaged but also cause fire
hazard by heat.
Cooling fans are provided to cool down the projector. This
projector monitors internal temperature and control the run-
ning speed of the cooling fans.
Do not point the projector down to
project an image.
NO DOWNWARD
Do not put the projector on either
side to project an image.
NO SIDEWARD
Moving the Projector
When moving the projector, replace the Lens Cover and
retract Adjustable Feet to prevent damage to the lens and
cabinet.
Air Intake Vent
When the projector is not in use for an extended period, put
it into the case (carrying bag) supplied with the projector.
Exhaust Vent
(Hot air exhaust)
CAUTION
Carrying Bag (supplied) is intended for protection from dust
and scratches on the surface of a cabinet, and it is not
designed to protect an appliance from external forces. Do not
transport a projector through a courier or transport services
with this bag, otherwise the projector can be damaged. When
handling a projector, do not drop, bump, subject it to strong
forces or put other things on the cabinet.
CAUTION IN CARRYING OR TRANSPORTING
THE PROJECTOR
– Do not drop or bump a projector, otherwise damages or
malfunctions may result.
– When carrying a projector, use a suitable carrying case.
– Do not transport a projector by using a courier or transport
service in an unsuitable transport case. This may cause
damage to a projector. To transport a projector through a
courier or transport service, consult your dealer for best
way.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance
Federal Communication Commission Notice
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures :
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such
changes or modifications should be made, you could be required to stop operation of the equipment.
Model Number
Trade Name
: LC-SD12
: EIKI
Responsible party : EIKI International, Inc.
Address
: 30251 Esperanza, Rancho Santa Margarita,
CA 92688-2132 U.S.A.
Telephone No.
: 800-242-3454 (949-457-0200)
AC Power Cord Requirement
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada :
AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the
plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be
unable to insert the plug into the outlet, contact your electrician.
GROUND
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Names and Functions
q Zoom Lever ( ☞ P20 )
w Infrared Remote Receiver ( ☞ P11 )
e Focus Ring ( ☞ P20 )
r Projection Lens ( ☞ P41 )
t Lens Cover ( ☞ P40 )
Front
q
w
y Air Intake Vent ( ☞ P40 )
u Exhaust Vent
CAUTION
i
u
e
r
Hot air is exhausted from the exhaust vent.
Do not put heat-sensitive objects near this side.
i Speaker
t
y
o Air Intake Vent ( ☞ P40 )
! Terminals and Connectors ( ☞ P9, 15, 16 )
! Power Cord Connector ( ☞ P14 )
! Exhaust Vent
Back
!
CAUTION
Hot air is exhausted from the exhaust vent.
Do not put heat-sensitive objects near this side.
o
!
!
!
! Air Intake Vent ( ☞ P40 )
! Top Controls and Indicators ( ☞ P10 )
!
! Air Filters ( ☞ P40 )
Bottom
! Air Intake Vents ( ☞ P40 )
! Adjustable Feet ( ☞ P13 )
!
!
CAUTION
Hot air is exhausted from the exhaust vents.
When using or installing the projector, the follow-
ing precautions should be taken.
–
–
–
Do not put any flammable objects near these
vents.
Keep front grills at least 3’(1m) away from any
objects, especially heat-sensitive objects.
Do not touch this area, especially screws and
metallic part. This area will become hot while
the projector is being used.
!
This projector detects internal temperature and
will automatically adjust the running speed of the
cooling fans.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Name and Functions
Terminals and Connectors
q
w
e
✽
RESET
VIDEO
S-VIDEO
SERVICE PORT
COMPUTER IN /
USB
COMPONENT IN/
AUDIO IN
COMPUTER /
COMPONENT
AV
u
y
t
r
q VIDEO
t AUDIO IN AV
Connect the composite video output from video
equipment. ( ☞ P16 )
Connect audio output from video equipment. ( ☞ P16 )
y AUDIO IN COMPUTER/ COMPONENT
Connect audio output from a computer or component to
this jack. ( ☞ P15, P16 )
w S-VIDEO
Connect S-video output from video equipment. ( ☞ P16 )
e SERVICE PORT
u COMPUTER IN / COMPONENT IN
Connect computer output, component output or RGB
Scart 21-pin video output to this connector. ( ☞ P15,
P16 )
This jack is used to service this projector.
r USB
Connect the USB port of your computer to this port
when you want to use the PAGE ed buttons on the
remote control to scroll back and forth pages on the
screen of the connected computer. ( ☞ P15, P38 )
✽ RESET button
A microprocessor included in the projector may occasionally
malfunction and need to be reset. If necessary, press this
button with a sharp tool to restart the unit. Do not use it
excessively.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Names and Functions
Top Controls and Indicators
i
u
y
WARNING
LAMP
POWER
REPLACE
t
r
q
w
e
INPUT
ON-OFF
MENU
SELECT
q POWER ON-OFF button
y LAMP REPLACE indicator
Turn the projector on or off. ( ☞ P17 )
Turn yellow when the life of the projection lamp draws
to an end. ( ☞ P42, 46 )
w SELECT button
u WARNING indicator
–Execute the selected item. ( ☞ P18 )
Light red when the projector is in the abnormal
condition. This indicator also flashes red when the
internal projector temperature goes up over the
operating range. ( ☞ P39, 46 )
–Expand / compress the image in Digital Zoom
mode. ( ☞ P29 )
+ / –
buttons
e Point ed7 8 ( VOLUME
)
– Select an item or adjust the value in the On-Screen
Menu. ( ☞ P18 )
– Pan the image in Digital zoom +/– mode. ( ☞ P29 )
– Adjust volume level. (the Point 7 8 buttons) ( ☞ P21 )
i POWER indicator
Flash red until the projector gets ready to be turned
on. It turns red when the projector is in the stand-by
mode. It remains green while the projector is in
operation. ( ☞ P17, 46 )
r MENU button
Open or close the On-Screen Menu. ( ☞ P18 )
t INPUT button
Select the input source. ( ☞ P22, 30, 31 )
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Name and Functions
q POWER ON-OFF button
Turn the projector on or off. ( ☞ P17 )
Remote Control
w VIDEO button
Select VIDEO input source. ( ☞ P30 )
e COMPUTER button
e
w
q
Select COMPUTER input source. ( ☞ P22, P31 )
r MENU button
Open or close the On-Screen Menu. ( ☞ P18 )
t PAGE ed buttons
Scroll back and forth pages on the screen when giving a
presentation. ( ☞ P9, P38 )
y D.ZOOM ed buttons
Select the Digital zoom +/– mode and resize the image.
( ☞ P29 )
-
COMPUTER VIDEO
ON OFF
u AUTO PC button
!
!
Automatically adjust a computer image to its optimum
setting. ( ☞ P24 )
r
i IMAGE button
-
+
MENU VOLUME SELECT VOLUME
Select the image level. ( ☞ P27, P33 )
o FREEZE button
!
!
!
Freeze the picture. ( ☞ P20 )
t
y
u
!
!
MUTE button
Mute the sound. ( ☞ P21 )
D.ZOOM PAGE KEYSTONE NO SHOW
P-TIMER button
-
TIMER
AUTO PC
P
Operate the P-timer function. ( ☞ P21 )
IMAGE FREEZE MUTE
!
NO SHOW button
Temporarily turn off the image on the screen. ( ☞ P21 )
!
KEYSTONE button
Correct keystone distortion. ( ☞ P20, P36 )
+ / –
! POINT ed 7 8 ( VOLUME
)
buttons
– Select an item or adjust the value in the On-Screen
Menu. ( ☞ P18 )
– Pan the image in Digital zoom +/– mode. ( ☞ P29 )
– Adjust the volume level. (the Point Left/Right buttons)
( ☞ P21 )
i
!
o
! SELECT button
– Execute the selected item. ( ☞ P18 )
– Expand / compress the image in Digital zoom mode.
( ☞ P29 )
To insure safe operation, please observe the following
precautions :
–
Do not bend, drop the remote control, or expose the
Remote Control to moisture or heat.
For cleaning, use a soft dry cloth. Do not apply
benzene, thinner, splay or any chemical material.
–
16.4’
(5 m)
Operating Range
Point the remote control toward the projector
(Infrared Remote Receiver) when pressing any
button. Maximum operating range for the remote
control is about 16.4’ (5m) and 60° in front of the
projector.
30°
30°
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Names and Functions
Remote Control Battery Installation
Remove the battery
compartment lid.
Slide the batteries into
Replace the compartment
lid.
1
2
3
the compartment.
Two AAA size batteries
For correct polarity (+ and
–), be sure battery
terminals are in contact
with pins in compartment.
Pull up and remove
the lid.
To insure safe operation, please observe the following precautions :
–
–
–
–
–
–
–
–
–
Use (2) AAA, SUM-4 or LR03 type alkaline batteries.
Replace two batteries at the same time.
Do not use a new battery with a used battery.
Avoid contact with water or liquid.
Do not expose the remote control to moisture, or heat.
Do not drop the remote control.
If a battery has leaked on the remote control, carefully wipe case clean and install new batteries.
Risk of an explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Positioning the Projector
– This projector is designed to project on a flat projection surface.
– The projector can be focused from 4.3’(1.3m) to 21.3’(6.5m).
– Refer to the figure below to adjust the screen size.
Note:
The brightness in a room has a great influence on the
picture quality. It is recommended to limit ambient lighting
in order to provide the best image.
A : B = 9 : 1
21.3’ (6.5m)
16.1’ (4.9m)
10.6’ (3.2m)
200”
Max. Zoom
150”
Min. Zoom
169”
4.3’ (1.3m)
100”
83”
A
127”
40”
34”
Center
B
Screen Size
(W x H) mm
4 : 3 aspect ratio
34"
40”
100”
150”
200”
4064 x 3048
–––––
691 x 518
4.3’ (1.3m)
813 x 610
4.9' (1.5m)
4.3’ (1.3m)
2032 x 1524
12.5' (3.8m)
10.6’ (3.2m)
3048 x 2286
19.0' (5.8m)
16.1' (4.9m)
Zoom (min)
Zoom (max)
21.3’ (6.5m)
–––––
Adjustable Feet
The picture tilt and the projection angle can be adjusted by rotating
the adjustable feet. The projection angle can be adjusted at 8.0
degrees.
Lift the front of the projector and pull the feet lock latches on
the both sides of the projector.
1
Release the feet lock latches to lock the adjustable feet and
rotate them to adjust position and tilt.
2
To retract the adjustable feet, lift the front of the projector
and pull and undo the feet lock latches.
Keystone distortion of the projected image can be adjusted
3
by the Menu Operation. ( ☞ P20, P36 )
CAUTION
Feet
Latches
Lock
Adjustable Feet
Tilt the projector within the adjustable angle not to shorten the lamp life.
Proper angle should be taken.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting the AC Power Cord
This projector uses nominal input voltages of 100-120 V or 200-240
V AC. This projector automatically selects the correct input
voltage. It is designed to work with single-phase power systems
having a grounded neutral conductor. To reduce risk of electrical
shock, do not plug into any other type of power system.
Consult your authorized dealer or service station if you are not sure
of the type of power supply being in use.
Connect a projector with a peripheral equipment before turning a
projector on. (Refer to page 15 –16 for connection.)
CAUTION
For safety, unplug the AC Power Cord when an appliance is not used.
When this projector is connected to the outlet with the AC Power Cord,
an appliance is in the Stand-by Mode and consumes a little electric
power.
Connect the AC Power Cord (supplied) to the
projector. The AC outlet must be near this
equipment and must be easily accessible.
Note:
The AC Power Cord must meet requirement of the country where you use the projector.
Confirm an AC plug type with the chart below and proper AC Power Cord must be used.
If supplied AC Power Cord does not match your AC outlet, contact your sales dealer.
Projector side
AC Outlet side
For the U.S.A. and Canada
For Continental Europe
Ground
To POWER CORD
CONNECTOR on your
projector.
To the AC Outlet.
(200 - 240 V AC)
To the AC Outlet.
(120 V AC)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting to a Computer
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)
Monitor Output
Audio Output
USB port
USB
Cable ✽
VGA Cable
Audio Cable
(Stereo) ✽
If you want to use the Page ▲▼ buttons
on the remote control, connect USB port
of your computer to the USB socket of
the projector. ( ☞ P38 )
RESET
VIDEO
S-VIDEO
SERVE PORT
COMPUTER IN /
COMPONENT IN/
USB
AUDIO IN
COMPUTER /
COMPONENT
AV
Note :
–See page 51 for ordering optional parts.
Cables used for connection
• VGA Cable ( Mini D-sub 15 pin )
• Audio Cable ( Mini Plug (stereo) ) ✽
• USB Cable ✽
When connecting the cable, the power cords of both the
projector and the external equipment should be
disconnected from AC outlet. Turn the projector and
peripheral equipment on before the computer is switched
on.
✽ Not supplied.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting to Video Equipment
Video Source (example)
Component video output
equipment. (such as DVD player or
high-definition TV source.)
Video Cassette Recorder
Video Disc Player
RGB Scart
21-pin Output
Audio Output
Component Video Output
(Y, Pb/Cb, Pr/Cr)
Composite
Video Output
S-VIDEO
Output
Audio Output
Component
Cable
(RCA x 3) ✽
Video
S-VIDEO Audio Cable
Audio Cable
(stereo) ✽
Scart-VGA
Cable✽
Cable ✽
(RCA x 1)
Cable ✽ (stereo) ✽
Component-
VGA Cable
(RCA x 3) ✽
RESET
VIDEO
S-VIDEO
SERVICE PORT
COMPUTER IN /
COMPONENT IN/
USB
AUDIO IN
COMPUTER /
COMPONENT
AV
Note :
–If both the S-VIDEO jack and the VIDEO jack are connected at the
same time when AUTO is selected in the Input Menu, the
S-VIDEO jack will override the signal from the VIDEO jack.
–See page 51 for ordering optional parts.
Cables used for connection
• Video Cable (RCA x 1) ✽
• S-VIDEO Cable ✽
• Audio Cables (Mini Plug) ✽
• Scart-VGA Cable ✽
• Component-VGA Cable (RCA x 3) ✽
• Component Cable (RCA x 3) ✽
When connecting the cable, the power cords of both the
projector and the external equipment should be
disconnected from AC outlet. Turn the projector and
peripheral equipment on before the computer is switched
on.
✽ Not supplied.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Turning On the Projector
Complete peripheral connections (with a computer, VCR, etc.)
before turning on the projector.
1
26
Connect the projector's AC Power Cord into an AC outlet. The
POWER indicator flashes in a moment and then turns red.
2
3
Press the POWER ON-OFF button on the top control or on the
remote control. The POWER indicator turns green, and the
cooling fans start to operate. The starting display appears on
the screen and the count-down starts.
– The starting display disappears after 30 seconds.
– The starting display can be changed. ( ☞ "Capture " P36 )
After the count-down, the input source that was selected last
and the Lamp mode status appear on the screen.
4
Selected Input Source and Lamp Mode
Lamp mode
( ☞ " Lamp mode " P37 )
Turning Off the Projector
Press the POWER ON-OFF button on the top control or on the
remote control, and the message " Power off? " appears on the
screen.
1
Press the POWER ON-OFF button again to turn off the
projector. The POWER indicator starts to flash red and
continues while the cooling fans are operating. (for approx. 90
seconds)
2
When the projector is cooled down enough to be turned on
again, the Power indicator turns red again. Then you can
disconnect the AC power cord.
Message disappears after 4 seconds.
3
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE
TURNING IT OFF.
DO NOT DISCONNECT THE AC POWER CORD WHILE
COOLING FANS ARE RUNNING OR BEFORE POWER
INDICATOR LIGHTS RED. OTHERWISE IT WILL RESULT IN
SHORTENING LAMP LIFE.
Note :
–
When the Power Management function is ON, the projector detects signal
interruption and automatically turns off the projection lamp. ( ☞ P 37 )
The projector cannot be turned on during the cooling period with the
POWER indicator flashing red. You can turn it on again after the POWER
indicator lights red.
Do not use the projector for more than 24 hours continuously. Turn off the
projector at least once in 24 hours and give it a rest. Continuous use may
result in shortening the lamp lifetime.
–
–
–
–
This projector detects internal temperature and automatically controls the
running speed of the cooling fans.
If the WARNING indicator flashes or lights red, see “Warning Indicator” on
page 39.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
How to Operate the On-Screen Menu
Menu bar
Menu icon
The projector can be adjusted or set via the On-Screen Menu.
Refer to the following pages regarding each adjustment and
setting procedure.
Press the MENU button to display the On-Screen Menu.
Pointer
(red frame)
1
Pointer (red frame)
Press the Pointd button to
move the pointer.
Press the Point7 8 buttons to select a Menu icon to adjust.
Press the Pointed buttons to select an item to adjust.
2
Item
Press the SELECT button to show the item data. Press the
Point7 8 buttons to adjust the data. Refer to the following
pages for respective adjustment.
3
SELECT
button
Note:
–The selected item is not in active until the SELECT button is pressed.
Item data
Press the Point7 8
buttons to adjust the
value or set the function.
COMPUTERRemote Control
Top Control
Point buttons
Point buttons
Used to move the
Pointer up/ down /
right / left.
Used to move the
Pointer up/ down /
right / left.
INPUT
F
MENU button
MENU
-
+
MENU VOLUME SELECT VOLUME
SELECT
MENU button
SELECT button
SELECT button
Used to select the item.
Used to select the item.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Menu Bar
For Computer Source
Guide Window
PC System Menu
Image Select Menu
Screen Menu
Setting Menu
Shows the selected
item of the On-
Screen Menu.
Used to select
the computer
Used to select an
image level among
Standard, Real,
Used to adjust the
size of image.
Used to change
settings of the
system. (
☞
P23 )
[Normal / True /
Wide / Digital zoom
projector or reset the
Lamp replace counter.
and Image 1 – 4.
(
☞
P27 )
+/–]
(
☞
P29 )
(
☞
P36-38 )
Input Menu
PC Adjust Menu
Image Adjust Menu
Sound Menu
Used to select the
input source
Used to adjust
parameters to
Used to adjust computer image.
[Contrast / Brightness / Color
temp. / White balance (R/G/B)
Gamma / Auto grayscale]
Used to adjust
the volume or
mute the sound.
either Computer
or Video.
match with the
input signal format.
/
(
☞
P21 )
(
☞
P22 )
(
☞
P24-26 )
(
☞
P28 )
For video source
Input Menu
Image Select Menu
Screen Menu
Used to select
the input source
either Video or
Computer.
Used to select an
image level among
Standard, Cinema and
Image 1 – 4.
Used to set size
of image to
Normal or Wide.
(
☞
P35 )
(
☞
P30-31 )
(
☞
P33 )
Same function as
menu for the
computer source.
Same function as menu
for the computer source.
Image Adjust Menu
Used to adjust the picture image.
AV System Menu
Used to select the
system of selected
video source.
[Contrast / Brightness / Color / Tint
Color temp. / White balance (R/G/B) /
Sharpness / Gamma / Auto
/
(
☞
P32 )
grayscale / Progressive]
(
☞
P34-35 )
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Zoom Adjustment
Tele
Move the Zoom Lever upward / downward to zoom the image.
Wide
Zoom Lever
Focus Adjustment
Rotate the Focus Ring to adjust the projected picture focus.
Focus Ring
Keystone Adjustment
If a projected picture has keystone distortion, correct image with the Keystone adjustment.
Press the KEYSTONE button on the remote control or select
Keystone on the Setting menu ( ☞ P36 ) to display the Keystone
dialog box.
1
Correct keystone distortion by pressing the Point ed buttons.
Press the Pointe button to reduce the upper part of image, and
Press the Pointd button to reduce the lower part.
2
–
–
Arrows are white in no correction.
The arrow of direction being corrected turns
red.
–
–
The arrow disappears at the maximum
correction.
If you press the KEYSTONE button on the
remote control once more while the keystone
dialog box is being displayed, the adjustment
will be canceled.
Reduce the upper width with the Point e button.
Reduce the lower width with the Point d button.
Picture Freeze Function
Press the FREEZE button on the remote control to freeze the picture
on-screen. To cancel the Freeze function, press the FREEZE button
again or press any other button.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
No Show Function
Press the NO SHOW button on the remote control to black out the
image. To restore to normal, press the NO SHOW button again or
press any other button. When a projected image is captured and set
as “User” in the Logo item in the Setting menu ( ☞ P36 ), the screen
changes each time you press the NO SHOW button as follows :
......
black out ➜ the captured image ➜ normal ➜
Message disappears after 4 seconds.
P-Timer Function
Press the P-TIMER button on the remote control. The timer display
“00 : 00” appears on the screen and the timer starts to count time (00
: 00 ~ 59 : 59).
To stop P-Timer display, press the P-TIMER button. And then, press
the P-TIMER button again to cancel P-Timer function.
Sound Adjustment
Indicates approximate
level of volume.
Direct Operation
Volume
Press the VOLUME +/– buttons on the remote control or on the top
control to adjust volume. The volume dialog box appears on the
screen for a few seconds.
The VOLUME + button to increase volume, and the VOLUME –
button for decreasing.
Mute
Press the MUTE button to set
Mute function "On" or "Off".
The display disappears after 4 seconds.
Press the MUTE button on the remote control to cut off sound. To
restore sound to its previous level, press the MUTE button again or
press Volume +/–.
Menu Operation
Sound Menu icon
SOUND MENU
Press the MENU button to display the On-Screen Menu. Press
1
the Point 7 8 buttons to move the red frame pointer to Sound
Menu icon.
Press the Point d button to move the red frame pointer to the
item that you want to select, and then press the SELECT button.
2
Indicates approximate
level of volume.
Volume
Close Sound Menu.
To increase volume, Press the Point 8 button, and Press the Point 7
button to decrease volume.
Mute
Press the Point 7 8 buttons to mute the sound. Dialog box display is
changed to “On” and sound is muted. To restore sound to its
previous level, press the Point 7 8 buttons again.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Input Source Selection
INPUT button
Computer
Direct Operation
Choose Computer by pressing the INPUT button on the top control or
the COMPUTER button on the remote control.
Before using these buttons, correct input source should be selected
through menu operation as described below.
Video
Menu Operation
Input Menu icon
Press the MENU button to display the On-Screen Menu. Press
the Point 7 8 buttons to move the red frame pointer to Input
Menu icon.
INPUT MENU
1
Press the Point d button to move the red arrow pointer to
Computer and then press the SELECT button. The Source
Select Menu will appear.
Move the pointer (red
arrow) to Computer and
press the SELECT button.
2
Move the pointer to the correct input source and press the
SELECT button.
3
Source Select Menu
When the input source is coming from a computer
through the COMPUTER IN / COMPONENT IN
terminal, select RGB.
RGB
Move the pointer to RGB and
press the SELECT button.
See P31"Input Source Selection (Component, RGB-
Scart 21-pin ) ".
Component
RGB (Scart)
See P31" Input Source Selection (Component, RGB-
Scart 21-pin ) ".
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Computer System Selection
This projector automatically tunes to various types of computers based on VGA, SVGA, XGA or SXGA with its Multi-scan
system and Auto PC Adjustment. If Computer is selected as a signal source, this projector automatically detects the signal
format and tunes to project a proper image without any additional setting. (Signal formats provided in this projector is
shown on page 49 )
Note : The projector may display one of the following messages.
When projector cannot recognize connected signal as PC
system provided in this projector, Auto PC Adjustment
function operates to adjust projector and the message
“Auto” is displayed on the System Menu icon. When
image is not provided properly, manual adjustment is
required. ( ☞ P25 - 26 )
PC SYSTEM MENU
Auto
System Menu icon
Displays system being
selected.
There is no signal input from computer. Make sure the
connection of computer and a projector is set correctly.
( ☞ " Troubleshooting" P44 )
-----
User preset adjustment in Computer Adjustment.
Adjustment data can be stored in Mode 1 - 5. ( ☞ P25-
26 )
Mode 1
Computer systems provided in the projector. The
projector chooses a proper system and displays it.
SVGA 1
*Mode 1 and SVGA 1 are examples.
System Menu icon
Displays system being selected.
PC SYSTEM MENU
Selecting Computer System Manually
PC system can be also selected manually.
Press the MENU button to display the On-Screen Menu. Press
the Point 7 8 buttons to move the red frame pointer to PC
System Menu icon.
The systems on this dialog box
can be selected.
1
Press the Point d button to move the red arrow pointer to the
2
system that you want to set, and then press
the SELECT button.
Custom Mode (1–5) set in PC
Adjust Menu. ( ☞ P25-26 )
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Auto PC Adjustment
Auto PC Adjustment function is provided to automatically conform Fine sync, Total dots and Picture Position to your
computer. This function can be operated as follows.
PC Adjust Menu icon
Auto PC Adj.
Press the MENU button to display the On-Screen Menu. Press
the Point 7 8 buttons to move the red frame pointer to the PC
Adjust Menu icon.
PC ADJUST MENU
1
2
Press the Point d button to move the red frame pointer to the
Auto PC Adj. icon and then press the SELECT button twice.
This Auto PC Adjustment can be also executed by pressing the
Auto PC button on the remote control.
Move the red frame pointer to Auto PC
Adj. icon and press the SELECT button.
To store adjustment parameters :
Adjustment parameters from Auto PC Adjustment can be memorized
in this projector. Once parameters are memorized, the setting can be
done just by selecting Mode in PC System Menu ( ☞ P23 ). Refer to
" Store " of Manual PC Adjustment section ( ☞ P26 ).
Note :
–
Fine sync, Total dots and Picture Position of some computers can not be
fully adjusted with this Auto PC Adjustment function. When the image is
not provided properly through this function, manual adjustments are
required. ( ☞ P25, 26 )
–
Auto PC Adjustment function cannot be operated when 480p, 575p, 480i,
575i, 720p (HDTV), 1035i (HDTV) or 1080i (HDTV) is selected on PC
SYSTEM Menu. ( ☞ P23).
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Manual PC Adjustment
Some computers employ special signal formats which may not be tuned by Multi-Scan system of this projector. In this
case, the projector cannot reproduce a proper image and the image may be recognized as a flickering picture, a non-
synchronized picture, a non-centered picture or a skewed picture.
The Manual PC Adjustment function allows you to precisely adjust several parameters to match those special signal
formats. You can store those adjusted parameters in the 5 independent memory areas, enabling you to call up whenever
you need.
PC Adjust Menu icon
Press the MENU button to display the On-Screen Menu. Press
the Point 7 8 buttons to move the red frame pointer to the PC
Adjust Menu icon.
PC ADJUST MENU
1
2
Press the Point d button to move the red frame pointer to the
item that you want to adjust and then press the SELECT button
to display the adjustment dialog box. Press the Point 7 8
buttons to adjust the value.
Move the red frame pointer to the item
and press the SELECT button.
Fine sync
Adjust an image as necessary to eliminate flicker from the display.
Press the Point 7 8 buttons to adjust the value.(From 0 to 31.)
Shows status
(Stored / Free) of the
selected Mode.
Total dots
Selected Mode
Adjust the number of total dots in one horizontal period. Press the
Point 7 8 buttons and adjust number to match your PC image.
Horizontal
Adjust horizontal picture position. Press the Point 7 8 buttons to
adjust the position.
Press the Point 7 8 buttons
to adjust the value.
Vertical
Adjust vertical picture position. Press the Point 7 8 buttons to
adjust the position.
Press the SELECT button at this
icon to adjust “Clamp,” “Display
area (H/V)” or set “Full screen.”
Current mode
Press the SELECT button to show the information of computer
selected.
Clamp
Current mode
Adjust clamp level. When the image has dark bars, try this
adjustment.
Press the SELECT button at
the Current Mode icon to
show the information of the
computer connected.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Display area
Select area displayed with this projector. Select the resolution at the
Display area dialog box.
Press the SELECT button at the
Display area icon to show the
Display area dialog box.
Display area H
Adjust the horizontal area displayed with this projector. Press the
Point 7 8 buttons to decrease/increase value to match the
resolution of image. Then press the SELECT button.
Display area
Display area V
Adjust the vertical area displayed with this projector. Press the Point
7 8 buttons to decrease / increase the value to match the resolution
of the image. Then press the SELECT button.
Full screen
Press the Point 7 8 buttons to switch Full screen function to “On”
or “Off.” Set “On” to resize the image with 4 x 3 aspect ratio to fit
the screen.
Note:
Display area, Display area (H/V) and Full screen cannot be adjusted when
480p, 575p, 480i, 575i, 720i(HDTV) , 1035i(HDTV) or 1080i(HDTV) is selected
on PC SYSTEM Menu. ( ☞ P23 ).
To clear adjustment data
Reset
Reset all adjust parameters on adjustment dialog box to previous
figures.
Mode free
To clear adjustment parameters previously set, move the red frame
pointer to the Mode free icon and then the SELECT button. Move
the red arrow pointer to the Mode that you want to clear and then
press the SELECT button.
Close this dialog box.
Store
To store adjustment parameters, move the red frame pointer to the
Store icon and then press the SELECT button. Move the red arrow
pointer to any of Mode 1 to 5 that you want to store to and then
press the SELECT button.
To store adjustment data
This Mode has parameters being stored.
Quit
Close PC Adjust Menu.
Vacant Mode
Shows values of “Total
dots,” “Horizontal,”
“Vertical,” “Display area H,”
and “Display area V.”
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Image Level Selection
Direct Operation
Select image level among Standard, Real, Image 1, Image 2, Image 3
and Image 4 by pressing the IMAGE button on the remote control.
IMAGE button
Standard
Real
Standard
Normal picture adjustment preset on this projector.
Image 1
Image 2
Image 3
Image 4
Real
Picture adjustment improved in reproduction of halftones. This
adjustment is suitable for providing better image in brighter place.
Image 1~4
User preset picture adjustment in Image Adjust Menu ( ☞ P28 ).
Image Select
Menu icon
Menu Operation
Press the MENU button to display the On-Screen Menu. Press
the Point 7 8 buttons to move the red frame pointer to the
Image Select Menu icon.
1
IMAGE SELECT MENU
Move the red frame pointer to the
level and press the SELECT button.
Press the Point d button to move the red frame pointer to the
level that you want to set and then press the SELECT button.
2
Standard
Normal picture adjustment preset on this projector.
Real
Picture adjustment improved in reproduction of halftones. This
adjustment is suitable for providing better image in brighter place.
The level being selected.
mage 1~4
I
User preset picture adjustment in Image Adjust Menu ( ☞ P28 ).
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Image Level Adjustment
Image Adjust
Menu icon
Press the MENU button to display the On-Screen Menu. Press
the Point 7 8 buttons to move the red frame pointer to the
Image Adjust Menu icon.
1
2
IMAGE ADJUST MENU
Press the Point d button to move the red frame pointer to the
item that you want to adjust, and then press the SELECT button.
The level of each item is displayed. Adjust each level by
pressing the Point 7 8 buttons.
Move the red frame pointer to
the item to be selected and
then press the SELECT button.
Contrast
Press the Point 7 8 buttons to adjust the image contrast.
(From 0 to 63.)
Brightness
Press the Point 7 8 buttons to adjust the image brightness.
(From 0 to 63.)
Selected Image level
Color temp.
Press the Point 7 8 buttons to select the Color temp. level you want
to select. (XLow, Low, Mid, or High)
White balance (Red)
Press the Point 7 8 buttons
to adjust the value.
Press the Point 7 8 buttons to adjust the red tone. (From 0 to 63.)
White balance (Green)
Press the Point 7 8 buttons to adjust the green tone. (From 0 to 63.)
White balance (Blue)
Press the Point 7 8 buttons to adjust the blue tone. (From 0 to 63.)
Store icon
Press the SELECT button at this
icon to store the adjustment.
Gamma
Press the Point 7 8 buttons to obtain better balance of contrast.
(From 0 to 15.)
Auto grayscale
When this function is "On", it automatically enhances contrast of
bright and dark part of the image.
Image Level Menu
Move the red frame
pointer to any of
Image 1 to 4 where
you want to set and
Reset
Reset all adjustments to previous figures.
then
SELECT button.
press
the
Store
To store manually preset image, move the red frame pointer to the
Store icon and press the SELECT button to display the Image Level
Menu. Move the red frame pointer to the Image 1 to 4 where you
want to set and then press the SELECT button.
A confirmation box will appear and select "Yes".
Quit
Close the Image Adjust Menu.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Screen Size Adjustment
This projector has a picture screen resize function, which enables you to customize the image size.
Screen Menu icon
Press the MENU button to display the On-Screen Menu. Press
the Point 7 8 buttons to move the red frame pointer to the
Screen Menu icon.
1
SCREEN MENU
Press the Point d button to move the red frame pointer to the
function that you want to select. Then press the SELECT button.
2
Move the red frame to the function
and press the SELECT button.
Normal
Provide an image to fit the screen size.
True
Note:
Provide image in its original size. When the original image size is
larger than screen size ( 800 x 600 ), this projector enters “Digital
zoom +” mode automatically.
– This Screen Menu cannot be operated when
720p(HDTV), 1035i(HDTV) or 1080i(HDTV) is
selected on PC System Menu. ( ☞ P23 ).
– True and Digital zoom +/– cannot be selected
when 480i, 575i, 480p, 575p is selected on PC
System Menu. ( ☞ P23 ).
Wide
Provide image to fit wide video aspect ratio (16 : 9) by expanding
image width uniformly. This function can be used for providing a
squeezed video signal at 16 : 9.
– This projector cannot display any resolution
higher than 1280 X 1024. If your computer’s
screen resolution is higher than 1280 X 1024,
reset the resolution to the lower before
connecting projector.
Digital zoom +
When Digital zoom + is selected, the On-Screen Menu disappears
and the message “D. Zoom +” is displayed. Press the SELECT
button to expand image size. And press the Point e d 7 8 buttons
to pan the image. The panning function can work only when the
image is larger than screen size.
A projected image can be also expanded by pressing the D.ZOOM e
button on the remote control.
– The image data in other than SVGA (800 x 600)
is modified to fit the screen size in initial mode.
– The panning function may not operate properly
if the computer system prepared on PC Adjust
Menu is used.
Digital zoom –
When Digital zoom – is selected, the On-Screen Menu disappears
and the message “D. Zoom –” is displayed. Press the SELECT
button to compress image size.
A projected image can be also compressed by pressing the D.ZOOM
▼ button on the remote control.
To cancel Digital zoom +/– mode, press any button except the
D.ZOOM ed buttons, the SELECT and the Point buttons.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Input Source Selection ( Video, S-Video )
INPUT button
Video
Direct Operation
Choose Video by pressing the INPUT button on the top control or the
VIDEO button on the remote control.
Before using these buttons, correct input source should be selected
through menu operation as described below.
Computer
Menu Operation
Input Menu icon
Press the MENU button to display the On-Screen Menu. Press
1
the Point 7 8 buttons to move the red frame pointer to the
Input Menu icon.
INPUT MENU
Press the Point d button to move the red arrow pointer to Video
and then press the SELECT button. Source Select Menu will
appear.
2
Move the red arrow pointer
to Video and press the
SELECT button.
Move the pointer to the source that you want to select and then
press the SELECT button.
3
VIDEO
When selecting Auto, the projector automatically detects
incoming video signal, and adjusts itself to optimize its
performance. The projector selects connection in the
following order:
Auto
Source Select Menu (VIDEO)
Move the pointer to the
source and press the SELECT
button.
1st S-VIDEO
2nd VIDEO
If both the S-VIDEO jack and the VIDEO jack are
connected at the same time when Auto is selected in the
Input Menu, the S-VIDEO jack will override the signal
from the VIDEO jack.
When video input signal is connected to VIDEO jack,
select Video.
Video
When video input signal is connected to S-VIDEO jack,
select S-Video.
S-Video
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Video input
Input Source Selection ( Component, RGB Scart 21-pin )
INPUT button
Video
Direct Operation
Choose Computer by pressing the INPUT button on the top control or
the COMPUTER button on the remote control.
Before using these buttons, correct input source should be selected
through menu operation as described below.
Computer
Menu Operation
Press the MENU button to display the On-Screen Menu. Press
the Point 7 8 buttons to move the red frame pointer to the
Input Menu icon.
1
Press the Point d button to move the red arrow pointer to
Computer and then press the SELECT button. The Source
Select Menu will appear.
2
Move the pointer to the source that you want to select and then
press the SELECT button.
Input Menu icon
3
INPUT MENU
When the input source is coming from video
equipment connected to the COMPUTER IN
/COMPONENT IN terminal with a Component-VGA
Cable, select Component.
Component
RGB (Scart)
Move the pointer (red
arrow) to Computer and
press the SELECT button.
When the input source is coming from video
equipment connected to the COMPUTER IN
/COMPONENT IN terminal with a Scart-VGA Cable,
select RGB (Scart).
Source Select Menu
Note :
Move the pointer to
Component or RGB ( Scart )
and press the SELECT button.
–Component-VGA Cable and Scart-VGA Cable are optionally supplied. See
page 51 for order.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Video System Selection
Press the MENU button to display the On-Screen Menu. Press
the Point 7 8 buttons to move the red frame pointer to the AV
System Menu icon.
1
2
Press the Point d button to move the red arrow pointer to the
system that you want to select and then press the SELECT
button.
Video Jack or S-Video Jack
AV SYSTEM MENU (VIDEO OR S-VIDEO)
Auto
The projector automatically detects incoming video system, and
adjusts itself to optimize its performance.
When Video System is PAL-M or PAL-N, select the system manually.
AV System Menu icon
This box indicates the
system being selected.
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
If projector cannot reproduce proper video image, it is necessary to
select a specific broadcast signal format among PAL, SECAM, NTSC,
NTSC4.43, PAL-M, and PAL-N.
Move the pointer to
the system and press
the SELECT button.
COMPUTER IN / COMPONENT IN Jack ( Y, Pb/Cb, Pr/Cr)
AV SYSTEM MENU (COMPONENT VIDEO)
Auto
The projector automatically detects incoming Video signal, and adjusts
itself to optimize its performance.
AV System Menu icon
This box indicates the
system being selected.
COMPONENT VIDEO SIGNAL FORMAT
If the projector cannot reproduce proper video image, it is necessary
to select a specific component video signal format among 480i, 575i,
480p, 575p, 720p, 1035i and 1080i.
Move the pointer to the
system and press the
SELECT button.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Image Level Selection
Direct Operation
Select image level among Standard, Cinema, Image 1, Image 2,
Image 3 and Image 4 by pressing the IMAGE button on the remote
control.
IMAGE button
Standard
Cinema
Image 1
Image 2
Image 3
Image 4
Standard
Normal picture adjustment preset on this projector.
Cinema
Picture level adjusted for the picture with fine tone.
Image 1~4
User preset picture adjustment in Image Adjust Menu ( ☞ P34-35 ).
Menu Operation
Press the MENU button to display the On-Screen Menu. Press
the Point 7 8 buttons to move the red frame pointer to the
Image Select Menu icon.
IMAGE SELECT MENU
1
Press the Point d button to move the red frame pointer to the
level that you want to set and then press the SELECT button.
2
Image Select
Menu icon
Move the red frame pointer to the
level and press the SELECT button.
Standard
Normal picture adjustment preset on this projector.
Cinema
Picture level adjusted for the picture with fine tone.
Image 1~4
The level being selected.
User preset picture adjustment in Image Adjust Menu ( ☞ P34-35 ).
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Image Level Adjustment
Press the MENU button to display the On-Screen Menu. Press
the Point 7 8 buttons to move the red frame pointer to the
Image Adjust Menu icon.
1
2
IMAGE ADJUST MENU
Press the Point d button to move the red frame pointer to the
item you want to adjust and then press the SELECT button. The
level of each item is displayed. Adjust each level by pressing
the Point 7 8 buttons.
Image Adjust
Menu icon
Move the red frame pointer
to the item to be selected
and then press the SELECT
button.
Contrast
Press the Point 7 8 buttons to adjust the image contrast.
(From 0 to 63.)
Brightness
Press the Point 7 8 buttons to adjust the image brightness.
(From 0 to 63.)
Color
Press the Point 7 8 buttons
to adjust the value.
Press the Point 7 8 buttons to adjust color intensity. (From 0 to 63.)
Tint
Press the SELECT button at this
icon to display other items.
Press the Point 7 8 buttons to obtain proper color. (From 0 to 63.)
Color temp.
Press the Point 7 8 buttons to select the Color temp. level that you
want to select. (XLow, Low, Mid, or High)
White balance (Red)
Press the Point 7 8 buttons
to adjust the value.
Press the Point 7 8 buttons to adjust the red tone. (From 0 to 63.)
White balance (Green)
Press the Point 7 8 buttons to adjust the green tone. (From 0 to 63.)
White balance (Blue)
Press the Point 7 8 buttons to adjust the blue tone. (From 0 to 63.)
Sharpness
Press the Point 7 8 buttons to adjust the image sharpness. (From 0 to 15.)
Press the SELECT button at this
icon to store the value.
Gamma
Press the Point 7 8 buttons to obtain better balance of contrast.
(From 0 to 15.)
Note :
–Tint cannot be selected when the video system is PAL, SECAM,
PAL-M or PAL-N.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Auto grayscale
When this function is "On", it automatically enhances contrast of
bright and dark part of image.
progressive
Interlace video signal can be displayed in a progressive picture.
Off ···· Not activated.
L1 ···· Select “L1” for an active picture.
L2 ···· Select “L2” for a still picture.
Note : The Progressive cannot be selected when 1080i, 1035i, 720p,
575p, or 480p is selected.
Reset
Reset all adjustments to previous figures.
Store
To store the adjusted data, move the red frame pointer to the
Store icon and press the SELECT button to display the Image
Level Menu. Move the red frame pointer to the Image Level 1
to 4 and then press the SELECT button.
Image Level Menu
Move the red frame
pointer to the image
icon to be set and
then press the
SELECT button.
A confirmation box will appear and select [Yes].
Quit
Close the Image Menu.
Store icon
Screen Size Adjustment
This projector has a picture screen resize function, which enables you to customize the image size.
Press the MENU button to display the On-Screen Menu. Press
the Point 7 8 buttons to move the red frame pointer to the
Screen Menu icon.
SCREEN MENU
1
2
Move the red frame to
the function and press
the SELECT button.
Press the Point d button and move the red frame pointer to the
function that you want to select and then press the SELECT
button.
Screen Menu icon
Normal
Provides image at a normal video aspect ratio of 4 : 3.
Wide
Provides image at a wide screen ratio of 16 : 9.
Note:
–The Screen Menu cannot be operated when 720p, 1035i, or 1080i is selected on
the AV System Menu ( ☞ P32 ).
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Setting Menu
Press the MENU button to display the On-Screen Menu. Press
the Point 7 8 buttons to move the red frame pointer to the
SETTING icon.
SETTING MENU
1
2
Press the Point d button to move the red frame pointer to the
item that you want to set. Then press the SELECT button to
display the Setting dialog box.
Setting Menu icon
Set the red frame
pointer to the item
and press the
SELECT button.
Language
Language used in the On-Screen Menu is selectable from among
English, German, French, Italian, Spanish, Portuguese, Dutch,
Swedish, Russian, Chinese, Korean and Japanese.
Keystone
This function corrects distortion of a projected image. Select either
Store or Reset with the Point 7 8 buttons, and then press the Select
button. The keystone dialog box appears. Adjust keystone with the
Point ed7 8 buttons.
Store . . . . . stores the keystone adjustment even if the AC power
cord is disconnected.
Press the SELECT button
at Language to show the
Language Menu.
Reset . . . . .resets the keystone adjustment when the AC power
cord is disconnected.
Blue back
When this function is “On,” the projector will project a blue image
on the screen if any input signal is not detected.
Display
This function decides whether to display On-Screen Displays.
On . . . . . .show all the On-Screen Displays.
Off . . . . . .set On-Screen Displays disappeared except;
• On-Screen Menu
• “Power off?” message ( ☞ P17 )
• P-TIMER ( ☞ P21)
Capture
• “No signal” message ( ☞ P37 )
• ”Wait a moment!” message
Logo
This function decides what to be displayed on the starting display.
User
Default ···· the factory set logo
Off ···· count-down only
···· the image you captured
Capture
This function is used to capture the image being projected and use it
for a start-up display. After capturing the projected image, go to the
Logo function (above) and set it as “User”. Then the captured
image will be displayed when turning on the projector next time.
To capture the image, select "Yes". To cancel the Capture function,
select "No".
Select [Yes] to capture
the projected image.
Select [No] to cancel.
Before capturing an image, select Standard in the Image Select
Menu to capture a proper image. ( ☞ P27, P33 )
A signal from a computer can be captured up to XGA (1024 x 768).
A signal from video equipment can be captured except for 720p,
1035i, and 1080i. When capturing the image that has been adjusted
by Keystone function, the adjusted data is automatically reset and
the projector captures an image without keystone adjustment.
Select [Yes] to
stop capturing.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Ceiling function
Rear function
Ceiling
When this function is “On”, picture is top / bottom and left / right
reversed. This function is used to project the image from a ceiling
mounted projector.
Rear
When this function is “On”, picture is left / right reversed. This
function is used to project the image to a rear projection screen.
Power management
Power management
For reducing power consumption as well as maintaining the lamp
life, Power management function turns off the projection lamp when
the input signal is interrupted and no button is pressed for 30
seconds or more.
If the input signal is interrupted and no button is pressed for 30
seconds or more, the timer display with the message " No signal"
appears on the screen. The count-down of the set time will get
started. The count-down time can be set between 1 and 30
minutes.
When the count-down time has been elapsed, the lamp will be
turned off to cool itself down. The POWER indicator is flashing red
during this cooling-off period. The next operation depends on the
setting as follows :
Press the SELECT button at Power
management to show this box.
Choose one of three settings with the
Point 7 8 buttons, and navigate to the
timer with the Point ed buttons and
set time with the Point 7 8 buttons.
Ready . . . . . . . . When the lamp has been fully cooled down, the
POWER indicator changes to green flashing. In
this condition, the projection lamp will be turned
on if the input signal is reconnected or any
button on the top control or the remote control is
pressed.
Shutdown . . . . . When the lamp has been fully cooled down, the
power will be turned off.
Off . . . . . . . . . . . Power management function is canceled.
Time left until Lamp off
Lamp mode
Lamp mode
This function allows you to change brightness of the screen.
Normal mode .....normal brightness
Auto mode .........the controlled brightness according to the
input signal
Eco mode...........lowers brightness, reduces the lamp power
consumption, and extends the lamp life.
Press the Point 7 8 buttons
to select lamp mode.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Remote Control
Remote control
This projector has two different remote control codes; the factory-
set normal code (Code 1) and the secondary code (Code 2). This
switching function prevents remote control interference when
operating several projectors or video equipment at the same time.
When operating the projector in “Code 2,” both the projector and
remote control must be switched to “Code 2.”
Press and hold
-
+
MENU VOLUME SELECT VOLUME
the MENU and the
IMAGE buttons for 10
seconds or more.
To change the code of the projector :
Set the remote control in the SETTING MENU to “Code 2.”
D.ZOOM PAGE KEYSTONE NO SHOW
To change the code of the remote control :
Press and hold both the MENU and the IMAGE buttons on the
remote control together for 10 seconds or more. After changing the
code, make sure the remote control operates properly.
To return to the normal code (Code 1), operate both the projector
and remote control in the ways above again.
-
TIMER
AUTO PC
P
IMAGE FREEZE MUTE
Note :
–When battery of the remote control is replaced, the remote control code
automatically returns to the normal code (Code 1).
USB
This projector is equipped with the USB port for interactive operation
between the projector and computer. Select either of the followings
as needed.
Key lock
···· When using the PAGE ed buttons on the remote
control. ( ☞ P9 )
···· When controlling the projector with a computer.
This item is provided for future use. Not available now.
Select Key lock to
display this box.
Choose one of
these with the
Point e d buttons
and select [Yes] to
activate it.
Key lock
This function locks operation of the top control and the remote
control. It is useful to prevent operation by a third person.
···· Not locked.
···· Lock the operation of the top control.
To unlock, use the remote control.
···· Lock the operation of the remote control.
To unlock, use the top control.
If the top control accidentally becomes locked and you do not have
the remote control nearby, disconnect the AC power cord to turn off
the power, and then while pressing the SELECT button, reconnect
the AC power cord. This will unlock the top control operation.
Factory default
Lamp counter reset
This function is used to reset the lamp replace counter. When
replacing the projection lamp, reset the lamp replace counter by
using this function. Refer to page 43 for operation.
Select Factory
default to show
this box. Select
[Yes] to activate it.
Factory default
This function returns all setting values except for the lamp counter to
the factory default settings.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Warning Indicator
The WARNING indicator shows the state of the function which protects the projector. Check the state of the WARNING
indicator and the POWER indicator to take proper maintenance.
The projector is shut down and the WARNING indicator is flashing red
When the temperature inside the projector exceeds the normal
temperature, the projector is automatically shut down to protect the
inside of the projector. The POWER indicator is flashing and the
projector is being cooled down. When the temperature inside the
projector returns to normal, the POWER indicator lights red and the
projector can be turned on.
Top Control
WARNING
LAMP
REPLACE
POWER
WARNING
flashing red
Note :
After the temperature inside the projector returns to normal, the WARNING
indicator still continues to flash. When the projector is turned on again, the
WARNING indicator stops flashing.
IN
F
Then check the items below.
✓ Did you provide appropriate space for the projector to be
ventilated? Check the installing condition to see if ventilation slots
are not blocked.
✓ Is the projector not installed near the ventilation duct of air-
conditioning equipment which may be hot? Install the projector
away from the ventilation duct of air-conditioning equipment.
✓ Are the air filters clean? Clean the air filters periodically.
The projector is shut down and the WARNING indicator lights red
When the projector detects an abnormal condition, it is automatically
shut down to protect the inside and the WARNING indicator lights
red. In this case, disconnect the AC power cord and reconnect it, and
then turn the projector on once again for check. If the projector is still
turned off and the WARNING indicator lights red, disconnect the AC
power cord and contact the service station for check and repair.
Top Control
WARNING
LAMP
REPLACE
POWER
WARNING
lights red
IN
CAUTION
F
DO NOT LEAVE THE PROJECTOR WITH THE AC POWER
CORD CONNECTED UNDER THE ABNORMAL
CONDITION. IT MAY RESULT IN FIRE OR ELECTRIC
SHOCK.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Air Filter
Removable air filters prevent dust from accumulating on the surface of optical elements inside the projector. Should air
filters become clogged with dust particles, it will reduce the cooling fans' effectiveness and may result in internal heat build
up and adversely affect the life of the projector. Clean air filters following the steps below:
Turn off the projector, and disconnect AC power cord from the
AC outlet.
Air filters
1
2
Turn the projector upside down and remove air filters by pulling
the latches upward.
Clean the air filters with a brush or wash out dust and particles.
3
4
Replace each air filter properly. Make sure that the air filters are
fully inserted.
CAUTION
Do not operate the projector with the air filters removed.
Dust may accumulate on optical elements inside the
projector degrading picture quality.
Do not put small parts into Air Intake Vents. It may result in
malfunction of the projector.
RECOMMENDATION
We recommend avoiding dusty/smoky environments when operating
a projector. Usage in these environments may cause poor image
quality.
When using under dusty or smoky conditions, dust may accumulate
on or optical elements inside the projector. This condition may
degrade the quality of a projected image.
When the above symptoms are noticed, contact your authorized
dealer or service station for proper cleaning.
Attaching the Lens Cover
Thread the string through the hole on the lens
1
cover and then tie a knot in the string to secure it
in place.
Thread the other end of the string through the
2
hole at the bottom of the projector. Then pass the
lens cover through the resulting loop of the string.
Tie a knot in the string to secure it in place.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Cleaning the Projection Lens
Follow these steps to clean the projection lens:
Disconnect the AC power cord before cleaning.
1
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning
cloth. Avoid using an excessive amount of cleaner. Abrasive
cleaners, solvents or other harsh chemicals might scratch a
surface.
2
Lightly wipe Projection Lens with a cleaning cloth.
3
4
When the projector is not in use, replace the Lens Cover.
Cleaning the Projector Cabinet
Follow these steps to clean the projector cabinet.
Disconnect the AC power cord before cleaning.
1
Lightly wipe the projector body with a soft, dry cleaning
cloth. When it is heavily soiled, use a small amount of mild
detergent and finish with a soft, dry cleaning cloth. Avoid
using an excessive amount of cleaner. Abrasive cleaners,
solvents, or other harsh chemicals might scratch the surface.
2
When the projector is not in use, put the projector in an
appropriate carrying case to protect it from being exposed to
the dust and being scratched.
3
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Lamp Replacement
When the life of the projection lamp draws to an end, LAMP
REPLACE indicator lights yellow. If this indicator lights yellow,
replace the projection lamp with a new one promptly.
TOP CONTROL
WARNING
POWER
LAMP
REPLACE
This indicator lights yellow when the life
of the projection lamp draws to an end.
INPU
CAUTION
Allow the projector to cool, for at least 45 minutes
before you open the Lamp Cover. The inside of the
projector can become very hot.
For continued safety, replace with the lamp assembly of
the same type.
Do not drop the lamp assembly or touch the glass bulb.
The glass can shatter and may cause injury.
Follow these steps to replace the lamp assembly.
Screw
Turn off the projector and disconnect the AC plug. Allow the
projector to cool at least for 45 minutes.
1
To remove the lamp cover, remove the screw with a screwdriver .
2
3
Lamp Cover
Remove two screws with a screwdriver and pull out the lamp
assembly by grasping the handle.
Replace the lamp assembly with a new one and tighten the two
screws back into the position. Make sure that the lamp
assembly is set properly. Replace the lamp cover and tighten
the screw.
4
Handle
Connect the AC Power Cord to the projector and turn on the
projector.
5
Reset the Lamp Replace Counter.
Refer to “Lamp Replace Counter” on the next page .
Lamp Assembly
6
Screws
Note :
–Do not reset the Lamp Replace Counter when the projection lamp has not
been replaced.
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through your dealer. When ordering a projection lamp, give the following
information to the dealer.
• Model No. of your projector
• Replacement Lamp Type No.
:
:
LC-SD12
POA-LMP57
(Service Parts No. 610 308 3117)
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Lamp Replace Counter
Be sure to reset the lamp replace counter after Lamp Assembly is replaced. When the lamp replace counter is reset, the
LAMP REPLACE Indicator stops lighting.
Setting Menu icon
Turn projector on, press the MENU button to display the
On-Screen Menu. Press the Point 7 8 buttons to move the
red frame pointer to the Setting Menu icon.
1
Press the Point d button to move the red frame pointer to
2
“Lamp counter reset” and then press
the SELECT button.
The message " Lamp replace counter reset? " is displayed.
Move the pointer to [Yes] and then press the SELECT
button.
Move the pointer to Lamp counter reset and then
press the SELECT button. The message “Lamp
replace counter reset?” is displayed.
Another confirmation dialog box appears and select [Yes] to
reset the lamp replace counter.
3
Note :
–Do not reset the Lamp Replace Counter until after the projection lamp is replaced.
LAMP HANDLING PRECAUTIONS
This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may
result in an accidents, injury, or create a fire hazard.
● Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no guarantee of
the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a shorter period of time than
other similar lamps.
● If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE INDICATOR lights up,
replace the lamp with a new one IMMEDIATELY after the projector has cooled down.
( Follow carefully the instructions in the LAMP REPLACEMENT section of this manual. ) Continuous use of the
lamp with the LAMP REPLACE INDICATOR lighted may increase the risk of lamp explosion.
● A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws
to an end. Risk of explosion may differ according to the environment or conditions in which the projector and
lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized
service station for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that
there are no broken shards or pieces of glass around the projector or coming out from the cooling air circulation
holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector
except those who are authorized trained technicians and who are familiar with projector service. Inappropriate
attempts to service the unit by anyone, especially those who are not appropriately trained to do so, may result in an
accident or injury caused by pieces of broken glass.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Troubleshooting
Before calling your dealer or service center for assistance, check the matters below once again.
– Make sure you have properly connected the projector to peripheral equipment as described in the section "Installation" on
P15-16.
– Make sure all equipment is connected to AC outlet and turned on the power.
– When you operate the projector with a computer, and it does not project an image, restart the computer.
– Try These Solutions
Problem:
No power.
– Plug the projector into your AC outlet.
– Make sure if the POWER indicator lights red.
– Wait 90 seconds after a projector is turned off when turning the projector back on.
The projector can be turned on after the Power indicator turns red. ( ☞ "Turning Off the
Projector " P17 )
– Check the WARNING indicator. If the indicator flashes red, the projector cannot be turned
on. ( ☞ "Warning Indicator " P39 )
– Check the projection lamp. ( ☞ P42-43 )
– Unlock Key lock for the projector in the Setting Menu. ( ☞ P38 )
Image is out of focus.
– Adjust focus of the projector. ( ☞ P20 )
– Provide proper distance between the projector and projection screen. ( ☞ P13 )
– Check the projection lens to see if it needs cleaning. ( ☞ P41 )
– Moving the projector from a cool temperature location to a warm temperature location may
result in moisture condensation on the projection lens. In this case, leave the projector off
and wait until condensation evaporates.
Picture is Left/Right
reversed.
– Check Ceiling / Rear item. ( ☞ “Setting” on page 37 )
Picture is Top/Bottom
reversed.
– Check Ceiling item. ( ☞ “Setting” on page 37 )
Some displays are not
seen during the
operation.
– Check Display item. ( ☞ “Setting” on page 36 )
No image.
– Check the connection between your computer or video equipment and the projector.
– Check if the input signal is correctly output from your computer. Some laptop computers
may need to change the setting for monitor output when connected to the projector. See
the computer's owner's manual for its setting.
– Check No Show function. ( ☞ P21 )
– When turning on the projector, it takes about 30 seconds to display an image.
– Check the system that you select is corresponding with your computer or video equipment.
– Select correct input source once again following the menu operation.
– Make sure the temperature is not out of the operating temperature range 41 ˚F – 95 ˚F
(5°C ~ 35°C).
No sound.
– Check audio cable connection from audio input source. ( ☞ P15-16 )
– Adjust the audio source.
– Press the VOLUME + button. ( ☞ P21 )
– Press the MUTE button. ( ☞ P21 )
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Problem: – Try These Solutions
Remote Control does
not work.
– Check the battery.
– Make sure nothing is between the infrared remote receiver and remote control.
– Make sure you are not too far from the projector when using the remote control.
Maximum operating range is 16.4’ ( 5m ).
– Make sure the code of the remote control is set to conform to the projector.
( ☞ P38 )
– Unlock Key lock for the remote control in the Setting Menu. ( ☞ P38 )
WARNING :
High voltages are used to operate this projector. Do not attempt to open the cabinet.
after following all operating instructions,
If the problem still persists
projector or the service center.
contact the sales dealer where you purchased the
Give the model number and explain the difficulty. We will advise you how to obtain service.
The CE Mark is a Directive conformity
mark of the European Community (EC).
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards
against risk of fire, casualty and electrical hazards.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Indicators and Projector Condition
Check the indicators for projector condition.
Indicators
Projector Condition
LAMP
WARNING
POWER
red/green
REPLACE
red
yellow
The projector is OFF. (The AC power cord is unplugged.)
The projector is preparing for stand-by or the projection lamp is being
cooled down. The projector cannot be turned on until cooling is completed.
✽
✽
✽
✽
The projector is ready to be turned on with the POWER ON-OFF button.
The projector is operating normally.
The projector is in the Power management mode.
The temperature inside the projector is abnormally high. The projector
cannot be turned on. When the projector is cooled down enough and the
temperature returns to normal, the POWER indicator lights red and the
projector can be turned on. (The WARNING indicator keeps flashing.)
Check and clean the air filters.
✽
✽
✽
The projector has been cooled down enough and the temperature returns
to normal. When turning on the projector, the WARNING indicator stops
flashing. Check and clean the air filters.
The projector detects an abnormal condition and cannot be turned on.
Unplug the AC power cord and plug it again to turn on the projector. If the
projector is turned off again, disconnect the AC power cord and contact the
dealer or the service center for service and checkup. Do not leave the pro-
jector on. It may cause an electric shock or a fire hazard.
• • • flashes red.
• • • off
• • • lights green.
• • • flashes green.
• • • lights red.
✽ When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow. When this indicator lights
yellow, replace the projection lamp with a new one promptly. Reset the Lamp replace counter after replacement of the lamp.
( ☞ P42-43 )
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Menu Tree
Main menu
Input
Computer
RGB
Go to System (1)
Go to System (2)
Component
RGB( Scart )
Quit
Video
Auto
Go to System (3)
Go to System (3)
Go to System (3)
Video
S-Video
Quit
Computer Input
Main menu
Image Select
Image Adjust
Standard
Real
Image 1
Image 2
Image 3
Image 4
MODE 1
System (1)
MODE 2
SVGA 1
- - - -
✽Systems displayed in the system menu vary
depending on the using environment.
Contrast
0 - 63
0 - 63
High
Mid
Brightness
Color temp.
PC Adjust
Auto PC Adj.
Fine sync
Total dots
Horizontal
Vertical
0 - 31
Low
XLow
Current mode
H-Sync.freq.
Red
Green
Blue
0 - 63
0 - 63
0 - 63
V-Sync.freq.
Quit
Clamp
Display area
Gamma
Auto grayscale
Reset
0 - 15
640 x 480
720 x 400
800 x 600
1024 x 768
1152 x 864
1280 x 1024
1400 x 1050
Quit
On / Off
Yes / No
Image 1
Image 2
Image 3
Image 4
Quit
Store
Quit
Display area H
Display area V
Full screen
Reset
Screen
Normal
True
Wide
Digital zoom +
Digital zoom –
On / Off
Yes / No
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Quit
Mode free
Store
Quit
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Quit
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Video Input
Settings
Main menu
Main menu
Sound
Auto
1080i
1035i
720p
575p
480p
575i
Volume
Mute
Quit
0 - 63
On / Off
System (2)
Setting
Language
English
German
French
Italian
480i
Spanish
Portuguese
Dutch
Auto
PAL
System (3)
Swedish
Russian
Chinese
Korean
Japanese
Quit
SECAM
NTSC
NTSC4.43
PAL-M
PAL-N
Keystone
Blue back
Display
Store / Reset
On / Off
On / Off
Image Select
Standard
Cinema
Image 1
Image 2
Image 3
Image 4
Logo
Off
User
Image Adjust
Contrast
Brightness
Color
Tint
Color temp.
0 - 63
0 - 63
0 - 63
0 - 63
High
Mid
Default
Yes/No
On / Off
On / Off
Off
Capture
Ceiling
Rear
Power management
Ready
Low
Shutdown
1 - 30 Min
Quit
XLow
Lamp mode
Normal
Auto
Eco
Red
Green
Blue
Sharpness
Gamma
Auto grayscale
Progressive
Reset
0 - 63
0 - 63
0 - 63
0 - 15
0 - 15
On / Off
Remote control
USB
Code 1
Code 2
Mouse
Projector
Off
Projector
Remote Control
Quit
L1 / L2 / Off
On / Off
Image 1
Image 2
Image 3
Image 4
Quit
Key Lock
Store
Lamp counter reset
Factory Default
Yes / No
Yes / No
Quit
Screen
Normal
Wide
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Compatible Computer Specifications
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than
100 MHz of Dot Clock.
ON-SCREEN
DISPLAY
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
H-Freq.
(kHz)
V-Freq.
(Hz)
RESOLUTION
RESOLUTION
VGA 1
VGA 2
VGA 3
VGA 4
VGA 5
VGA 6
VGA 7
MAC LC13
MAC 13
480p
640 x 480
720 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
31.47
31.47
31.47
37.86
37.86
37.50
43.269
34.97
59.88
70.09
70.09
74.38
72.81
75.00
85.00
66.60
66.67
59.88
50.00
XGA 2
XGA 3
XGA 4
XGA 5
XGA 6
XGA 7
XGA 8
XGA 9
XGA 10
XGA 11
XGA 12
XGA 13
XGA 14
XGA 15
MAC 19
MAC 21
SXGA 1
SXGA 11
SXGA 13 1280 x 1024
SXGA 14 1280 x 1024
SXGA 17
SXGA 18 1280 x 1024
720p (HDTV)
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 870
1152 x 864
1152 x 900
68.677
60.023
56.476
60.31
48.50
44.00
63.48
36.00
62.04
61.00
35.522
46.90
47.00
58.03
60.24
68.68
64.20
61.20
50.00
50.00
61.85
46.43
45.00
33.75
33.75
28.125
84.997
75.03
70.07
74.92
60.02
54.58
79.35
87.17
(Interlace)
35.00
640 x 480
––––––––
77.07
75.70
31.47
31.25
15.734
15.625
35.156
37.88
46.875
53.674
48.08
37.90
34.50
38.00
38.60
32.70
38.00
49.72
48.36
86.96
––––––––
––––––––
––––––––
575p
480i
575i
(Interlace)
60
58.20
58.30
72.00
75.08
75.06
70.40
65.20
(Interlace)
50
(Interlace)
SVGA 1
SVGA 2
SVGA 3
SVGA 4
SVGA 5
SVGA 6
SVGA 7
SVGA 8
SVGA 9
SVGA 10
SVGA 11
MAC 16
XGA 1
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
56.25
60.32
75.00
85.06
72.19
61.03
55.38
60.51
60.31
51.09
60.51
74.55
60.00
86.00
(Interlace)
94.00
(Interlace)
1152 x 900
66.00
86.70
(Interlace)
––––––––
60.00
60.00
––––––––
1035i (HDTV)
(Interlace)
60.00
(Interlace)
50.00
(Interlace)
––––––––
1080i (HDTV)
––––––––
1080i (HDTV)
Note:
–Specifications are subject to change without notice.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Technical Specifications
Multi-media Projector
Projector Type
10.63" x 3.07" x 7.48" (270mm x 78.0mm x 190mm) (not including Adjustable Feet)
4.6lbs (2.1 kg)
(W x H x D)
Dimensions
Net Weight
0.5" TFT Active Matrix type, 3 panels
800 x 600 dots
LCD Panel System
Panel Resolution
Number of Pixels
Color System
High Definition TV Signal
Scanning Frequency
Projection Image size
Projection Lens
Throw Distance
1,440,000 (800 x 600 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
480i, 480p, 575i, 575p, 720p, 1035i, and 1080i
H-sync. 15 ~ 80 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 34” to 200”
F 1.6 ~ 1.8 lens with f 18.3 mm ~ 21.9 mm with manual zoom and focus
4.3’ ~ 21.2’ (1.3 m ~ 6.5 m)
(Diagonal)
160 W
Projection Lamp
RCA Type x 1 (Video) and Mini DIN 4 pin x 1 (S-Video)
Mini Jack (stereo) x 1
Video Input Jack
Audio Input Jack
Analog RGB (Mini D-sub 15 pin) x 1
Mini Jack (stereo) x 1
Computer Input Terminal
Computer Audio Input Jack
Control Port Connector
USB Connector
Mini DIN 8 pin x 1
USB Series B receptacle x 1
0.8 W RMS
Internal Audio Amp
Built-in Speaker
1 speaker, ø1.3" (32mm)
0˚ to 8.0˚
Feet Adjustment
Voltage and
Power Consumption
AC 100 ~ 120 V (2.4 A Max. Ampere), 50 / 60 Hz (The U.S.A and Canada)
AC 200 ~ 240 V (1.2 A Max. Ampere), 50 / 60 Hz (Continental Europe)
41 ˚F – 95 ˚F (5 ˚C – 35 ˚C)
Operating Temperature
14 ˚F – 140 ˚F (-10 ˚C – 60 ˚C)
Storage Temperature
Remote Control
Power Source
Operating Range
Dimensions
:
:
:
:
AAA, SUM-04 or LR03 type x 2
16.4’ (5m) / 30˚
2.0”(W) x 0.91”(H) x 4.8”(D) (51.5mm x 23.2mm x 123mm)
2.11oz (60 g) (including battery)
Net Weight
Owner’s Manual
AC Power Cord
Accessories
Remote Control and Battery
VGA Cable
Carrying Bag
Lens Cover
String for Lens Cover
– The specifications are subject to change without notice.
– LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a tiny
fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Configuration of Terminals
COMPUTER INPUT TERMINAL (ANALOG)
Terminal : Analog RGB (Mini D-sub 15-PIN)
1
2
3
4
5
6
7
8
R / Cr, Pr Input
G / Y Input
B / Cb, Pb Input
No Connect
9
No Connect
Pin Configuration
10 Ground (Vert.sync.)
11 Ground
12 No Connect
2
1
5
4
3
10
9
8
7
6
15
14
13
12
11
Ground (Horiz.sync.) 13 Horiz. sync.
Ground (Red)
Ground (Green)
Ground (Blue)
14 Vert. sync.
15 No Connect
SERVICE PORT CONNECTOR
Terminal : Mini DIN 8-PIN
Pin Configuration
PS/2
-----
-----
-----
GND
-----
-----
-----
-----
Serial
R X D
-----
-----
GND
-----
T X D
-----
ADB
-----
-----
-----
GND
-----
-----
-----
-----
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
-----
USB CONNECTOR (Series B)
Pin Configuration
1
2
3
4
Vcc
- Data
+ Data
Ground
2
3
1
4
Optional Parts
The parts listed below are optionally supplied. When ordering those parts, give name and Type No. of it to the sales dealer.
• COMPONENT-VGA Cable
• SCART-VGA Cable
Type No. : POA-CA-COMPVGA
Type No. : AH-98881 (POA-CA-SCART)
51
Download from Www.Somanuals.com. All Manuals Search And Download.
A-key to better communications
Canada
U.S.A.
EIKI International, Inc.
30251 Esperanza
EIKI CANADA - Eiki International, Inc.
P.O. Box 156, 310 First St. - Unit 2,
Midland, ON, L4R 4K8, Canada
Tel : 800-563-3454 (705)-527-4084
Fax : 800-567-4069 (705)-527-4087
E-Mail : [email protected]
Rancho Santa Margarita
CA 92688-2132
U.S.A.
Tel : 800-24-3454 (949)-457-0200
Fax : 800-457-3454 (949)-457-7878
E-Mail : [email protected]
Eastern Europe
EIKIˆ CZECH spol. s.r.o.
Umelecká 15
170 00 Praha 7
Czech Republic
Tel : +42 02 20570024
+42 02 20571413
Fax : +42 02 20571411
E-Mail : [email protected]
Deutschland & Österreich
EIKI Deutschland GmbH
Am Frauwald 12
65510 Idstein
Deutschland
Tel : 06126-9371-0
Fax : 06126-9371-14
E-Mail : [email protected]
Japan & Worldwide
EIKI Industrial Company Limited.
4-12 Banzai-Cho, Kita-Ku, Osaka,
530-0028 Japan
Tel : +81-6-6311-9479
Fax : +81-6-6311-8486
E-Mail : [email protected]
Printed in China
Part No. 610 321 9899 (1AA6P1P4799-A MP3BD-A)
© 2004 Eiki International, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|