X7722271404 / X772000164
SHC-266
Shaft Hedge Trimmer
Operator’s Manual
Burn Hazard
The muffler or catalytic muffler and surrounding cover may become extremely hot.
Always keep clear of exhaust and muffler area, otherwise serious personal injury may
occur.
The engine exhaust from this product contains chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
Users of this equipment risk injury to themselves and others if the unit is used
improperly and/or safety precautions are not followed. ECHO provides an operator’s
manual and a safety manual. Both must be read and understood for proper and safe
operation. Failure to do so could result in serious injury.
Specifications, descriptions and illustrative material in this literature are as accurate as known at the time
of publication, but are subject to change without notice. Illustrations may include optional equipment and
accessories, and may not include all standard equipment.
X7502026704
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SHC-266
INTRODUCTION
INTRODUCTION
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and
on-the-job dependability. Read and understand this manual and the SAFETY MANUAL. You will find both
easy to use and full of helpful operating tips and SAFETY messages.
The Operator’s Manual
Keep it in a safe place for future reference. Contains specifications and information for safety, operation,
maintenance, storage and assembly specific to this product.
The Safety Manual
Keep it in a safe place for future reference. Explains possible hazards and the measures you should take to
insure safe operation.
SERVICING INFORMATION
Parts/Serial Number
Genuine ECHO Parts and ECHO REPOWER™ Parts and
Assemblies for your ECHO products are available only from an
Authorized ECHO Dealer. When you do need to buy parts always
have the Model Number and Serial Number of the unit with you. You
can find these numbers on the engine housing. For future
reference, write them in the space provided below.
Model No. _________________ SN. ___________________
Service
Service of this product during the warranty period must be performed by an Authorized ECHO Service
Dealer. For the name and address of the Authorized ECHO Service Dealer nearest you, ask your retailer or
call: 1-800-432-ECHO (3246). Dealer information is also available on our Web Site. When presenting your
unit for Warranty service/repairs, proof of purchase is required.
Echo Consumer Product Support
If you require assistance or have questions concerning the application, operation or maintenance of this
product you may call the ECHO Consumer Product Support Department at 1-800-673-1558 from 8:00 am to
5:00 pm (Central Standard Time) Monday through Friday. Before calling, please know the model and serial
number of your unit.
Product Registration
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at
product confirms your warranty coverage and provides a direct link between you and ECHO if we find it
necessary to contact you.
X7502026704
3
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
SHC-266
Additional or Replacement Manuals
For more information
scan this QR code.
Replacement Operator, Safety Manuals, and Parts Catalogs
or by contacting ECHO Inc., 400 Oakwood Road, Lake Zurich,
IL 60047 (800-673-1558). Always check the ECHO Web Site for
updated information.
Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.
SAFETY
Manual Safety Symbols and Important Information
Throughout this manual and on the product itself, you will find safety alerts and helpful, informational
messages preceded by symbols or key words. The following is an explanation of those symbols and key
words and what they mean to you.
The safety alert symbol accompanied by the word “DANGER” calls attention to an act or condition
which WILL lead to serious personal injury or death if not avoided.
The safety alert symbol accompanied by the word “WARNING” calls attention to an act or condition
which CAN lead to serious personal injury or death if not avoided.
The safety alert symbol accompanied by the word “CAUTION” calls attention to an act or condition
which may lead to minor or moderate personal injury if not avoided.
The enclosed message provides information necessary for the protection of the unit.
Note: This enclosed message provides tips for use, care and maintenance of the unit.
CIRCLE AND SLASH SYMBOL
This symbol means the specific action shown is prohibited. Ignoring these prohibitions can result
in serious or fatal injury.
4
X7502026704
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SHC-266
SAFETY
International Symbols
Symbol
Description
Symbol
Description
Symbol
Description
Symbol
Description
Carburetor
Adjustment - Low
speed mixture
Carburetor
Adjustment - High
speed mixture
Read and
understand
owners manual.
Fuel and oil
mixture
Wear eye, ear
and head
Carburetor
Adjustment - Idle
speed
Finger severing
Hot Surface
Safety/Alert
protection
Avoid all power
lines. This unit is
not insulated
against electrical
current.
Do not operate
closer than 15 M
(50 ft.) from
Emergency Stop
electrical hazard.
Wear hand and
foot protection.
Use two handed
Plan retreat path
from falling
objects
DO NOT smoke
near fuel
Primer Bulb
Choke Control
“COLD START”
Position (Choke
Closed)
DO NOT allow
flames or sparks
near fuel
Ignition
ON / OFF
Wear slip
resistant footwear
Do not operate
closer than 15 M
(50 ft.) from
Keep bystanders
at least
4.5 meters (15 ft.)
away.
Choke Control
“RUN” Position
(Choke Open)
Chain Lubrication.
electricalhazards.
X7502026704
5
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
SHC-266
Personal Condition and Safety Equipment
Users of this product risk injury to themselves and others if the unit is used improperly and/or safety
precautions are not followed. Proper clothing and safety gear must be worn when operating unit.
Physical Condition
Your judgment and physical dexterity may not be good:
• If you are tired or sick.
• If you are taking medication.
• If you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection
• Eye protection that meets ANSI Z87.1 or CE requirements must be worn whenever you operate the
unit.
• For additional safety, a full-face shield may be worn over safety glasses or goggles to provide
protection from sharp branches or flying debris.
Hand Protection
Wear sturdy, no-slip, rubber work gloves to improve your grip on the handles. Gloves also provide protection
against cuts and scratches, cold environments, and reduce the transmission of machine vibration to your
hands.
Hearing/Ear Protection
ECHO recommends wearing hearing protection whenever unit is used.
Breathing Protection
Operators who are sensitive to dust or other common airborne allergens may need to wear a dust mask to
prevent inhaling these materials while operating unit. Dust masks can provide protection against dust, plant
debris, and other plant matter such as pollen. Make sure the mask does not impair your vision, and replace
the mask as needed to prevent air restrictions.
Proper Clothing
Wear snug-fitting, durable clothing:
• Pants should have long legs, shirts should have long sleeves.
• DO NOT WEAR SHORTS.
• DO NOT WEAR TIES, SCARVES, JEWELRY, or clothing with loose or hanging items that could become
entangled in moving parts or surrounding growth.
• Keep clothing buttoned or zipped, and keep shirt tails tucked in.
Wear sturdy work shoes with nonskid rubber soles:
• DO NOT WEAR OPEN TOED SHOES.
6
X7502026704
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SHC-266
SAFETY
• DO NOT OPERATE UNIT BAREFOOTED.
Keep long hair away from engine and air intake. Retain hair with cap or net.
Heavy protective clothing can increase operator fatigue, which may lead to heat stroke. Schedule heavy
work for early morning or late afternoon hours when temperatures are cooler.
The components of this machine generate an electromagnetic field during operation, which may
interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with
pacemakers should consult with their physician and the pacemaker manufacturer before operating
this machine. In the absence of such information, ECHO does not recommend the use of ECHO
products by anyone who has a pacemaker.
Extended Operation / Extreme Conditions
Prolonged exposure to cold and/or vibration may result in injury. Read and follow all safety and
operation instructions to minimize risk of injury. Failure to follow instructions may result in painful
wrist/hand/arm injuries.
It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals,
may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling
and burning sensations, followed by loss of color and numbness in the fingers. The following precautions are
strongly recommended, because the minimum exposure, which might trigger the ailment, is unknown.
• Keep your body warm, especially the head, neck, feet, ankles,
hands, and wrists.
• Maintain good blood circulation by performing vigorous arm
exercises during frequent work breaks, and also by not
smoking.
• Limit the hours of operation. Try to fill each day with jobs
where operating the unit or other hand-held power equipment
is not required.
• If you experience discomfort, redness, and swelling of the
fingers followed by whitening and loss of feeling, consult your physician before further exposing yourself to
cold and vibration.
X7502026704
7
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
SHC-266
Repetitive Stress Injuries (RSI)
It is believed that overusing the muscles and tendons of the fingers,
hands, arms, and shoulders may cause soreness, swelling,
numbness, weakness, and extreme pain in those areas. Certain
repetitive hand activities may put you at a high risk for developing a
Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal
Tunnel Syndrome (CTS), which could occur when your wrist swells
and squeezes a vital nerve that runs through the area. Some believe
that prolonged exposure to vibration may contribute to CTS. CTS
can cause severe pain for months or even years.
To reduce the risk of RSI/CTS, do the following:
• Avoid using your wrist in a bent, extended, or twisted position.
Instead try to maintain a straight wrist position. Also, when
grasping, use your whole hand, not just the thumb and index finger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive movement.
• Do exercise to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if you feel tingling, numbness, or pain in
the fingers, hands, wrists, or arms. The sooner RSI/CTS is diagnosed, the more likely permanent nerve
and muscle damage can be prevented.
All over head electrical conductors and communications wires can have electricity flow with high
voltages. This unit is not insulated against electrical current. Never touch wires directly or indirectly,
otherwise serious injury or death may result.
Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains
poisonous emissions and can cause serious injury or death.
Read the Manuals
• Provide all users of this equipment with the Operator’s Manual and Safety Manual for instructions on Safe
Operation.
Clear the Work Area
• Spectators and fellow workers must be warned, and children and animals prevented from coming nearer
than 15 m (50 ft.) while the unit is in use.
Keep a Firm Grip
• Hold the support handle and throttle handle with thumbs and fingers encircling the grips.
8
X7502026704
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SHC-266
SAFETY
Keep a Solid Stance
• Maintain footing and balance at all times. Do not stand on
slippery, uneven or unstable surfaces. Do not work in odd
positions or on ladders. Do not over reach.
Avoid Hot Surfaces
For more information
scan this QR code.
• During operation, the drive shaft housing and attachment bearing
housing may become very hot, too hot to touch. Avoid contact
during and immediately after operation.
Never perform blade maintenance procedures while engine is running.
Equipment
Use only ECHO attachments. Serious injury may result from the use of a non-approved attachment
combination. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or
accessories which have not been tested and approved by ECHO. Read and comply with all safety
instructions listed in this manual and safety manual.
• Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed.
• Check that the cutting attachment is firmly attached and in safe operating condition. Dull, loose or
damaged blades should not be used.
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings.
• ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a
complete stop before removing obstructions, clearing debris, or servicing unit.
• DO NOT start or operate unit unless all guards and protective covers are properly assembled to
unit.
• NEVER reach into any opening while the engine is running. Moving parts may not be visible
through openings.
Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage or
leaks are found, do not use unit, otherwise serious personal injury or property damage may occur.
Have unit repaired by an authorized servicing dealer before using.
X7502026704
9
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
EMISSION CONTROL (EXHAUST & EVAPORATIVE)
EMISSION CONTROL (EXHAUST & EVAPORATIVE)
EPA 2010 and Later and/or C.A.R.B. TIER III
SHC-266
The emission control system for the engine is EM (engine modification)
and, if the second to last character of the Engine Family on the Emission
Control Information label (sample below) is “C”, “K”, or “T”, the emission
control system is EM and TWC (3-way catalyst). The fuel tank/fuel line
emission control system is EVAP (evaporative emissions). Evaporative
emissions for California models are only applicable to fuel tanks.
An Emission Control Label is located on the engine. (This is an
EXAMPLE ONLY, information on label varies by engine FAMILY).
Product Emission Durability (Emission Compliance Period)
The 50 or 300 hour emission compliance period is the time span
selected by the manufacturer certifying the engine emissions output
meets applicable emissions regulations, provided that approved
maintenance procedures are followed as listed in the Maintenance Section of this manual.
10
X7502026704
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SHC-266
DESCRIPTION
DESCRIPTION
Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow
the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See
PARTS ORDERING instructions for specific information.
12
11
15
19
10
18
13
14
17
16
6
5
7
8
4
3
2
1
9
Shaft Label
Hot Label
X7502026704
11
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION
SHC-266
1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter.
2. THROTTLE HANDLE - FOR RIGHT HAND - Contains Stop Switch, Throttle Lockout, and Throttle
Trigger.
3. THROTTLE TRIGGER LOCKOUT - This lever must be held during starting. Operation of the throttle
trigger is prevented unless throttle trigger lockout lever is engaged.
4. STOP SWITCH - “SLIDE SWITCH” mounted on top of the throttle handle. Move switch FORWARD to
RUN, BACK to STOP.
5. SUPPORT HANDLE - FOR LEFT HAND - Grip for Left Hand.
6. DRIVE SHAFT ASSEMBLY - Includes the flex drive shaft, throttle handle, support handle, and safety
decals.
7. BLADES - Double reciprocating blades mounted to a blade support bar. Double sided blades, are
capable of cutting on either side.
8. GEAR HOUSING ASSEMBLY - Gear housing assembly fixed straight extension.
9. THROTTLE TRIGGER - Spring loaded to return to idle when released. During acceleration, depress
gradually for best operating technique.
10. BLADE COVER - Used to cover blade during transport and storage. Remove blade cover before using
unit.
11. SPARK PLUG - Provides spark to ignite fuel mixture.
12. TOP GUARD - Protects arm from the hot engine.
13. SPARK ARRESTOR MUFFLER OR SPARK ARRESTOR MUFFLER WITH CATALYST - The muffler or
catalytic muffler controls exhaust noise and emission. The spark arrestor screen prevents hot, glowing
particles of carbon from leaving the muffler. Keep exhaust area clear of flammable debris.
14. FUEL TANK - Contains fuel and fuel filter.
15. RECOIL STARTER HANDLE - Pull handle slowly until starter engages, then quickly and firmly. When
engine starts, return handle slowly. DO NOT let handle snap back or damage to unit will occur.
16. FUEL TANK CAP - Covers and seals fuel tank opening.
17. PURGE BULB - Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging
air from the carburetor. Pump purge bulb until fuel is visible and flows freely in the clear fuel tank return
line. Pump purge bulb an additional 4 or 5 times.
18. AIR CLEANER - Contains replaceable filter element.
19. CHOKE CONTROL - Located on the air cleaner housing. Move choke lever to COLD START (
close choke for cold start. Move choke lever to “RUN” ( ) position to open choke.
) to
12
X7502026704
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SHC-266
CONTENTS
CONTENTS
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or
missing parts. Use the contents list to check for missing parts.
____ Power Head/Drive Shaft Assembly
____ Gear Case Assembly
____ Operator's Manual
____ Emission Control Warranty Statement
____ Safety Manual
____ Blade Cover
____ Assembly Tool(s)
X7502026704
13
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
SHC-266
ASSEMBLY
Gear Housing Assembly / Drive Shaft
Note: Hedge Trimmer Blades are very sharp. Wear gloves to
protect hands.
A
1. Remove locating bolt (A) and loosen clamping bolt (B).
2. Remove vinyl cap from drive shaft.
B
3. Slide Gear Housing Assembly onto Drive Shaft. Be certain
the Flex Drive Shaft engages the hole in Driver Gear.
C
Flat edge of washer (C) must be against drive shaft.
4. Align locating hole in gear housing with locator hole in drive shaft.
5. Install locating bolt (A). Tighten clamping bolt (B).
OPERATION
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts
have come to a complete stop before removing obstructions, clearing debris, or servicing unit.
Operation of this equipment may create sparks that can start fires. This unit is equipped with a spark
arrestor to prevent discharge of hot particles from the engine. Metal cutters can create sparks if the
cutter strikes rocks, metal, or other hard objects. Contact local fire authorities for laws or
regulations regarding fire prevention requirements.
Fuel
Alternative fuels, such as E-15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO
requirements are NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels
may cause performance problems, loss of power, overheating, fuel vapor lock, and unintended
machine operation, including, but not limited to, improper clutch engagement. Alternative fuels may
also cause premature deterioration of fuel lines, gaskets, carburetors and other engine components.
Fuel Requirements
Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may
contain up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing
methanol (wood alcohol) is NOT approved. ECHO brand Power Fuel™ is 93 octane, ethanol-free fuel
premixed with ECHO Red Armor® engine oil at 50:1 ratio. Use of ECHO Power Fuel™ is recommended to
extend engine life in all air-cooled 2-stroke and 2/4-stroke hybrid engines.
14
X7502026704
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SHC-266
OPERATION
Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FD Standards
must be used. Echo brand premium Power Blend X™ Universal 2-Stroke Oil meets these standards. Engine
problems due to inadequate lubrication caused by failure to use an ISO-L-EGD (ISO/CD 13738) and
J.A.S.O. FD certified oil, such as Echo premium Power Blend X™, will void the two-stroke engine warranty.
Echo premium Power Blend X™ Universal 2-Stroke Oil may be mixed at 50:1 ratio for application in all Echo
engines sold in the past regardless of ratio specified in those manuals.
Handling Fuel
Fuel is VERY flammable. Use extreme care when mixing, storing or handling, or serious personal
injury may result.
• Use an approved fuel container.
• DO NOT smoke near fuel.
• DO NOT allow flames or sparks near fuel.
• Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to
equalize.
• NEVER refuel a unit when the engine is HOT or RUNNING!
• DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground.
• DO NOT overfill fuel tank. Wipe up spills immediately.
• Securely tighten fuel tank cap and close fuel container after refueling.
• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is
repaired.
• Move at least 3m (10 ft.) from refueling location before starting the engine.
Mixing Instructions
1. Fill an approved fuel container with half of the required
amount of gasoline.
2. Add the proper amount of 2-stroke oil to gasoline.
3. Close container and shake to mix oil with gasoline.
4. Add remaining gasoline, close fuel container, and remix.
Spilled fuel is a leading cause of hydrocarbon emissions. Some
states may require the use of automatic fuel shut-off containers
to reduce fuel spillage.
For more information
scan this QR code.
After use
• DO NOT store a unit with fuel in its tank. Leaks can occur.
Return unused fuel to an approved fuel storage container.
X7502026704
15
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
SHC-266
Storage - Fuel storage laws vary by locality. Contact your local government for the laws affecting your area.
As a precaution, store fuel in an approved, airtight container. Store in a well-ventilated, unoccupied building,
away from sparks and flames.
Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a
fuel stabilizer is added.
Stored two-stroke fuel may separate. ALWAYS shake fuel container thoroughly before each use.
Starting Cold Engine
Hedge Trimmer blades are very sharp. Touching them may lead to severe personal injury. Avoid
touching blades whenever possible, and always wear gloves to protect hands.
Note: The blade cover is used for transportation and storage. Remove blade cover before using the unit.
The attachment will operate immediately when the engine starts, and could result in possible
serious injury. Keep movable parts of the attachment away from objects that could become
entangled or thrown, and surfaces that could cause loss of control.
1. Stop Switch
Move stop switch (A) away from the STOP position.
A
2. Choke
Move choke (B) to COLD START (
) (closed) position.
3. Purge Bulb
B
C
Pump purge bulb (C) until fuel is visible and flows freely in the
clear fuel tank return line. Pump bulb an additional 4 or 5
times.
D
16
X7502026704
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SHC-266
OPERATION
4. Recoil Starter
Lay the unit on a flat area and keep movable attachment parts
clear of all obstacles. Firmly grasp throttle handle and throttle
trigger lockout with left hand and fully depress throttle trigger
to wide open position. Rapidly pull recoil starter handle/rope
(D) until engine fires (or maximum five [5] pulls).
5. Choke
After engine fires (or 5 pulls), move choke (B) to the RUN
D
(
)(open)position. Firmlygraspthrottlehandleandthrottle
trigger lockout with left hand and fully depress throttle trigger
to wide open position. Pull starter handle/rope until engine
starts and runs. Release throttle trigger and allow unit to warm up at idle for several minutes.
Note: If engine does not start with choke in “RUN” position after 5 pulls, repeat instructions 2 - 5.
The blades must not move at idle, otherwise serious personal injury may result. Periodic carburetor
adjustment may be necessary to assure blades do not move at idle. If blades move, readjust
carburetor according to “Carburetor Adjustment” instructions in this manual or see your ECHO
Dealer.
6. Throttle Trigger
After engine warm-up, grip throttle handle and support handle. Depress the throttle trigger lockout, and
gradually depress throttle trigger to increase engine RPM to operating speed.
Starting Warm Engine
A
The starting procedure is the same as Cold Start except DO
NOT close the choke, and do not depress throttle trigger to wide
open position.
The blades must not move at idle, otherwise serious
personal injury may result. Periodic carburetor adjustment
may be necessary to assure blades do not move at idle. If
blades move, readjust carburetor according to “Carburetor
Adjustment” instructions in this manual or see your ECHO
Dealer.
1. Stop Switch
Move stop switch (A) away from the STOP position.
2. Purge Bulb
Pump purge bulb (C) until fuel is visible and flows freely in the
clear fuel tank return line. Pump bulb an additional 4 or 5
times.
B
C
D
X7502026704
17
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
SHC-266
3. Recoil Starter
Lay the unit on a flat area and keep movable attachment parts
clear of all obstacles. Firmly grip throttle handle and throttle
trigger lockout with left hand. Rapidly pull recoil starter
handle/rope (D) until engine fires.
Note: If engine does not start after 5 pulls, use Cold Start
Procedure.
D
Stopping Engine
A
1. Throttle
Release throttle trigger and allow engine to return to idle
before shutting off engine.
2. Stop Switch
Move stop switch (A) to STOP position.
If engine does not stop when stop switch is moved to STOP position, close choke - COLD START
position - to stall engine. Have your ECHO dealer repair stop switch before using unit again.
Hedge Trimming
Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause
unconsciousness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position
unit so that exhaust is directed away from your face and body.
Hedge Trimmer blades are very sharp. Touching them may
lead to severe personal injury. Avoid touching blades
whenever possible, and always wear gloves to protect
hands.
1. Always grip throttle handle with right hand and support
handle with left hand.
2. Hold trimmer firmly and squeeze throttle trigger to
accelerate engine.
3. Tilt trimmer so cutting teeth are angled slightly toward the
hedge or shrub and proceed to cut.
18
X7502026704
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SHC-266
OPERATION
Never remove hands from unit when blades are moving.
The engine continues running even when the blades have stopped due to an obstruction. If this
occurs, stop the engine, disconnect ignition cable and remove the obstruction.
X7502026704
19
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
SHC-266
MAINTENANCE
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts
have come to a complete stop before removing obstructions, clearing debris, or servicing unit.
Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and
hot surfaces.
Your ECHO unit is designed to provide many hours of trouble free service. Regular scheduled maintenance
will help your unit achieve that goal. If you are unsure or are not equipped with the necessary tools, you may
want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to
DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is
not listed, see your ECHO Dealer for repairs.
Skill Levels
Level 1 = Easy to do. Common tools may be required.
Level 2 = Moderate difficulty. Some specialized tools may be required.
ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier.
Maintenance Intervals
DAILY
REQ’D
MAINTENANCE
PROCEDURE
OR
EVERY
3
COMPONENT/SYSTEM
SKILL
YEARLY
BEFORE REFUEL MONTHS
USE
LEVEL
Air Filter
Inspect/Clean
1
1
1
1
1
1
2
2
2
2
I / C *
I / C
R *
Choke Shutter
Fuel Filter
Inspect/Clean
Inspect/Replace
Inspect/Replace
Inspect/Replace
Inspect/Clean/Replace
Inspect/Clean
I *
I *
I / R *
R *
Fuel Cap Gasket
Fuel System
I (3) *
I / C
I (3) *
Spark Plug
I / C / R *
Cooling System
Muffler Spark Arrestor
Cylinder Exhaust Port
Inspect/Clean/Replace
Inspect/Clean/Decarbon
Grease
I / C / R *
I / C
Drive Shaft (flex cable
models)
I (1)
Gear Housing
Blades
Grease
2
1
1
1
I (1)
Inspect/Clean
Inspect/Clean
Inspect/Tighten/Replace
I / C (2)
I / C *
I *
Recoil Starter Rope
Screws/Nuts/Bolts
MAINTENANCE PROCEDURE LETTER CODES: I = INSPECT, R = REPLACE, C = CLEAN
IMPORTANT NOTE - Time intervals shown are maximum. Actual use and your experience will determine the
frequency of required maintenance.
MAINTENANCE PROCEDURE NOTES:
1. Apply lithium-based grease every 25 hours of use.
2. Inspect blade, and clean and sharpen as needed. Lubricate blades periodically during use
20
X7502026704
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SHC-266
MAINTENANCE
3. Low evaporative fuel tanks DO NOT require regular maintenance to maintain emission integrity.
* Replacement is recommended based on the finding of damage or wear during inspection.
Air Filter
Level 1
REPOWERTM AIR & FUEL FILTER KIT.
Parts Required:
1. Close choke (COLD START [
] position). This prevents
dirt from entering the carburetor throat when the air filter is
removed. Brush accumulated dirt from air cleaner area.
2. Remove air filter cover and air filter retainer from inside
cover. Brush dirt from inside cover.
3. Replace filter if it is damaged, very dirty, or the rubber sealing edges are deformed.
4. Remove foam pre-filter and air filter and clean as indicated
below:
Foam Pre-filter
• Clean foam filter in water/detergent solution and rinse with
clean water.
• Wrap the filter in a clean, dry cloth and squeeze (do not
wring) dry. Allow to dry completely before reuse. Do not oil.
Dual Layer Air Filter
• Lightly brush debris from filter.
• Soak heavily soiled filters in water/detergent solution to loosen dirt, then brush lightly.
• Rinse with clean water and allow to dry completely before reuse.
5. Place foam pre-filter over raised center and inside outer lip of air filter. Install air filter in air filter case.
6. Install air filter retainer on post in air filter cover, flat side up.
7. Install air filter cover and tighten cover knob securely.
X7502026704
21
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
SHC-266
Fuel Filter
Level 1
REPOWERTM AIR & FUEL FILTER KIT.
Parts Required:
Fuel is VERY flammable. Use extreme care when mixing,
storing or handling, or serious personal injury may result.
1. Use a clean rag to remove loose dirt from around fuel cap
and empty fuel tank.
2. Use a hook to pull the fuel line and filter from the tank.
3. Remove the filter from the line and install the new filter.
Note: Federal EPA regulations require all model year 2012 and later gasoline powered engines produced for
sale in the United States to be equipped with a special low permeation fuel supply hose between the
carburetor and fuel tank. When servicing model year 2012 and later equipment, only fuel supply
hoses certified by EPA can be used to replace the original equipment supply hose. Fines up to
$37,500 may be enforced for using an un-certified replacement part.
Spark Plug
Level 2
REPOWERTM Tune-Up Kit
Parts Required:
Use only NGK BPM-8Y spark plug (BPMR-8Y in Canada)
otherwise severe engine damage may occur.
0.65 mm (0.026 in.)
1. Remove spark plug and check for fouling, worn and rounded
center electrode.
2. Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage
engine.
3. Adjust spark plug gap by bending outer electrode.
4. Tighten spark plug to 150–170 kgf • cm (130–150 in • lbf).
22
X7502026704
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SHC-266
MAINTENANCE
Cooling System
Level 2
Parts Required: None if you are careful.
To maintain proper engine operating temperatures, cooling air must pass freely through the cylinder fin area.
This flow of air carries combustion heat away from the engine.
Overheating and engine seizure can occur when:
• Air intakes are blocked, preventing cooling air from reaching
the cylinder.
• Dust and grass build up on the outside of the cylinder. This
build up insulates the engine and prevents the heat from
leaving.
Removal of cooling passage blockages or cleaning of cooling
fins is considered “Normal Maintenance.” Any failure attributed
to lack of maintenance is not warranted.
1. Remove spark plug lead.
2. Remove air cleaner cover.
3. Remove muffler cover (A).
4. Remove engine cover (B).
A
DO NOT use a metal scraper to remove dirt from the cylinder fins.
B
5. Use brush to remove dirt from the cylinder fins.
6. Remove grass and leaves from the grid between the recoil
starter and fuel tank.
7. Assemble components in reverse order.
X7502026704
23
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Exhaust System
SHC-266
Spark Arrestor Screen
Level 2
A
Parts Required: Spark Arrestor Screen, Gasket
1. Remove spark plug lead.
2. Remove muffler cover (A).
C
3. Place piston at Top Dead Center (TDC) to prevent
carbon/dirt from entering cylinder.
D
B
4. Remove spark arrestor screen (D), gasket (C) and exhaust
guide (B) from muffler body.
5. Clean carbon deposits from muffler components.
Note: When cleaning carbon deposits, be careful not to damage the catalytic element inside muffler.
6. Replace screen if it is cracked, plugged, or has holes burned through.
7. Assemble components in reverse order.
Exhaust Port Cleaning
B
A
Level 2
Parts Required: As needed; Heat Shield
1. Remove spark plug lead from spark plug, and remove
engine cover.
2. Place piston at top dead center. Remove muffler (A) and
heat shield (B).
3. Use a wood or plastic scraping tool to clean deposits from
cylinder exhaust port.
Never use a metal tool to scrape carbon from the exhaust port. Do not scratch the cylinder or piston when
cleaning the exhaust port. Do not allow carbon particles to enter the cylinder.
4. Inspect heat shield, and replace if damaged.
5. Install heat shield and muffler.
6. Tighten muffler mounting bolts (or nuts) to 90–110 kgf • cm
(80–95 in • lbf).
7. Install engine cover and attach spark plug lead.
8. Start engine, and warm to operating temperature.
9. Stop engine, and re-tighten mounting bolts (or nuts) to
specifications.
24
X7502026704
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SHC-266
MAINTENANCE
Carburetor Adjustment
Level 2
Engine Break-In
New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor
adjustments can be made. During the break-in period your engine performance will increase and exhaust
emissions will stabilize. Idle speed can be adjusted as required.
High Altitude Operation
This engine has been factory adjusted to maintain satisfactory starting, emission, and durability
performance up to 1,100 feet above sea level (ASL) (96.0 kPa). To maintain proper engine operation and
emission compliance above 1,100 feet ASL the carburetor may need to be adjusted by an authorized ECHO
service dealer.
If the engine is adjusted for operation above 1,100 feet ASL, the carburetor must be re-adjusted when
operating the engine below 1,100 feet ASL, otherwise severe engine damage may result.
Parts
None
Required:
Note: Every unit is run at the factory and the carburetor is set in compliance with emission regulations.
Carburetor adjustments, other than idle speed, must be performed by an authorized ECHO dealer.
1. Check idle speed and reset if necessary. If a tachometer is
available, idle speed screw (A) should be set to the
specifications found on “Specifications” page of this manual.
Turn idle screw (A) clockwise to increase idle speed;
counterclockwise to decrease idle speed.
A
When carburetor adjustment is completed, the cutting
attachment should not move at idle, otherwise serious
personal injury may result.
Lubrication
Blades
Level 1.
Parts Required: 20W Engine Oil (blade lubrication), 50-50
mixture of kerosene and 20W oil (blade
cleaning)
Hedge Trimmer blades are very sharp. Touching them may
lead to severe personal injury. Avoid touching blades
whenever possible, and always wear gloves to protect
hands.
X7502026704
25
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
SHC-266
1. Brush loose debris from blade and coat both sides of blade with the 50-50 cleaning mixture.
2. Allow cleaning mixture to soften the remaining gummy residue then wipe it from the blade.
3. Apply clean oil to the entire length of the blade. Be certain the blade bolts are lubricated.
4. Wipe excess oil from the blade before putting the unit back in service.
Gear Case
Level 1.
Parts Required: Lithium Based Grease.
1. Clean dirt from the grease fitting (A).
A
2. Carefully pump grease into fitting (A). DO NOT force grease.
Too much pressure will force grease past seals and cause
damage. Apply 1 - 2 pumps of grease every 15 - 25 hours of
operation.
3. Wipe excess grease from around grease fitting.
Drive Shaft Assembly
Level 1.
Parts Required: Lithium Based Grease.
Hedge Trimmer blades are very sharp. Touching them may lead to severe personal injury. Avoid
touching blades whenever possible, and always wear gloves to protect hands.
1. Remove gear housing locating screw (A) and loosen
A
clamping screw (B). Remove the gear housing assembly
from the drive shaft housing.
D
B
26
X7502026704
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SHC-266
MAINTENANCE
2. Pull the drive shaft (C) from the housing, wipe clean and
re-coat with a thin coating [15 ml (1/2 oz.)] of grease.
A
D
B
3. Slide the drive shaft back in the drive housing being careful
not to get dirt on the flex shaft.
4. Install the gear housing assembly.
C
Flat edge of washers (D) must be against drive shaft.
Blades
Blades should only be removed and reinstalled by an Authorized ECHO Servicing Dealer, otherwise
premature wear or internal damage may occur.
Sharpening
Level 2.
Parts Required: none
Hedge Trimmer blades are very sharp. Touching them may lead to severe personal injury. Avoid
touching blades whenever possible, and always wear gloves to protect hands.
1. Move stop switch to STOP position.
2. Disconnect spark plug wire.
A
X7502026704
27
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
SHC-266
3. Remove blade guard, if installed (see “Blade Guard
Remove/Install instructions”).
6 mm (.25 in.) radius
4. Slide blades to allow file clearance using slots (A) on bottom
of blade. Do not pry against cutting edges.
5. File each edge carefully. Follow the original shape of the
blade.
45o
If a power grinder is used DO NOT allow blade to over heat.
6. Install blade guard, if necessary (see “Blade Guard
Remove/Install instructions”).
7. Lubricate blades (see “Lubrication”).
8. Connect spark plug wire.
Adjustment
Level 2.
Parts Required: none
Hedge Trimmer blades are very sharp. Touching them may
lead to severe personal injury. Use long hex wrenches and
sockets with extensions when tightening blade screws and
blade lock nuts to keep hands at a safe distance from sharp
blades.
1. Tighten blade screws (A) securely.
2. Hold blade screws (A) to prevent turning, and tighten lock
nuts (B).
A
Locking ability of Hedge Trimmer blade lock nuts will diminish
each time they are removed. Replace if turning resistance is not
felt when installing lock nuts.
B
28
X7502026704
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SHC-266
TROUBLESHOOTING
TROUBLESHOOTING
ENGINE PROBLEM TROUBLESHOOTING CHART
Problem
Check
Status
Cause
Remedy
Fuel strainer clogged
Fuel line clogged
Carburetor
Clean or replace
Clean or replace
See your Echo dealer
Fuel at carburetor No fuel at carburetor
No fuel at cylinder
Carburetor
See your Echo dealer
Open choke
Fuel at cylinder
Clean/replace air filter
Adjust carburetor
See your Echo dealer
Muffler wet with fuel
Fuel Mixture too rich
Enginecranks-
starts hard/
doesn’t start
Stop switch OFF
Electrical problem
Interlock switch
Turn switch to ON
See your Echo dealer
See your Echo dealer
Spark at end of
No spark
plug wire
Spark gap incorrect
Adjust to 0.65mm
(0.026 in.)
Spark at plug
No spark
Covered with carbon
Fouled with fuel
Plug defective
Clean or replace
Clean or replace
Replace plug
Air filter
Air filter dirty
Normal wear
Clean or replace
Contaminants/residues
in fuel
Fuel filter
Fuel filter dirty
Replace
Contaminants/residues
in fuel
Engine runs,
but dies or
does not
accelerate
properly
Fuel vent
Fuel vent plugged
Clean or replace
Spark Plug
Carburetor
Plug dirty/worn
Normal wear
Vibration
Clean and adjust or replace
Adjust
Improper adjustment
Cooling system
dirty/plugged
Extended operation in
dirty/dusty locations
Cooling System
Clean
Spark Arrestor
Screen
Spark arrestor screen
plugged
Normal wear
Replace
Engine does
not crank
N/A
N/A
Internal engine problem See your Echo dealer
Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition
spark by grounding spark plug near cylinder plug hole, otherwise serious personal injury may
result.
X7502026704
29
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
SHC-266
STORAGE
The muffler and surrounding cover become hot during operation. Always keep exhaust area clear of
flammable debris during transportation or when storing, otherwise serious property damage or
personal injury may result.
Long Term Storage (Over 30 Days)
Do not store your unit for a prolonged period of time (30 days or longer) without performing protective
storage maintenance which includes the following:
1. Store unit in a dry, dust free place, out of the reach of children.
Hedge Trimmer blades are very sharp. Touching them may lead to severe personal injury. Avoid
touching blades whenever possible, and always wear gloves to protect hands.
Do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark,
otherwise serious personal injury may result.
2. Place the stop switch in the “STOP” position.
3. Remove accumulation of grease, oil, dirt and debris from exterior of unit.
4. Perform all periodic lubrication and services that are required.
5. Apply clean oil to the entire length of the blade. Be certain the blade bolts are lubricated.
6. Install blade cover on blades.
7. Tighten all the screws and nuts.
8. Drain fuel tank completely. Press purge bulb 6 -7 times to remove remaining fuel from carburetor then
drain the tank again. Close choke, start and run the engine until it stops due to lack of fuel.
9. Allow the engine to cool, then emove the spark plug and pour 7 cc (1/4 oz.) of fresh, clean, two-stroke
engine oil into the cylinder through the spark plug hole.
a. Place a clean cloth over the spark plug hole.
b. Pull the recoil starter handle 2-3 times to distribute the oil inside the engine.
c. Observe the piston location through the spark plug hole. Pull the recoil handle slowly until the piston
reaches the top of its travel and leave it there.
10. Install the spark plug (do not connect ignition cable).
Always store and transport hedge trimmers in a stable, horizontal position. Support gear case and cutting
blades to prevent excessive flexing, which may cause damage to these components. Always install blade
cover when transporting or storing unit.
30
X7502026704
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SHC-266
SPECIFICATIONS
SPECIFICATIONS
MODEL
Length
SHC-266
2170 mm (85.4 in.)
250 mm (9.85 in.)
254 mm (10.0 in.)
6.58 kg (14.5 lb.)
Width
Height
Weight (dry)
Engine Type
Bore
Air cooled, two-stroke, single cylinder gasoline engine
34.0 mm (1.34 in.)
Stroke
28.0 mm (1.10 in.)
Displacement
Exhaust
25.4 cc (1.55 cu. in.)
Spark arrestor muffler or spark arrestor muffler with catalyst
Diaphragm w/purge pump
Carburetor
Ignition System
Spark Plug
Fuel
Flywheel magneto, capacitor discharge ignition type
NGK BPM-8Y (Gap 0.65 mm (0.026 in.)
Mixed (Gasoline and Two-stroke Oil)
50 : 1 Power Blend XTM or ECHO Red Armor® ISO-L-EGD (ISO/CD 13738) and J.A.S.O.
M345- FD, two-stroke, air-cooled engine oil.
Fuel/Oil Ratio
Gasoline
Use 89 Octane unleaded. Do not use fuel containing methyl alcohol, more than 10% ethyl
alcohol or 15% MTBE. Do not use alternative fuels such as E-15 or E-85.
Oil
Power Blend XTM or ECHO Red Armor® Premium Universal 2-Stroke Oil
Fuel Tank Capacity
Starter System
Clutch
0.48 L (16.4 US fl. oz.)
Automatic Recoil Starter
Centrifugal Type
Gear Case Ratio
Cutter
4.27:1
Double Reciprocating Blade, Double Edge
480 mm (18.9 in.)
Length
Pitch
35 mm (1.38 in.)
Maximum Diameter Cut:
Soft Material
Woody Material
Idle Speed
25.4 mm (1 in.)
13 mm (1/2 in.)
2,900 RPM
Clutch Engagement Speed
3,900 RPM
Wide Open Throttle Speed (W.O.T.) 10,900 RPM
X7502026704
31
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY STATEMENTS
SHC-266
WARRANTY STATEMENTS
ECHO LIMITED WARRANTY STATEMENT FOR
PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010
ECHO'S RESPONSIBILITY
ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship.
Under normal use and maintenance from date of purchase, ECHO agrees to repair or replace at ECHO’s discretion, any defective product
free of charge at any authorized ECHO servicing dealer within listed below application time periods, limitations and exclusions. THIS LIMITED
WARRANTY IS ONLYAPPLICABLE TO ECHO PRODUCTS SOLD BYAUTHORIZED ECHO DEALERS. IT IS EXTENDED TO THE ORIGINAL
PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair
parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period. Any
damage caused by improper installation or improper maintenance is not covered by this warranty. All parts or products replaced under warranty
become the property of ECHO, Inc. This warranty is separate from the Emission control warranty statement supplied with your new product.
Please consult the Emission Control Warranty Statement for details regarding emission related parts. For a list of Authorized ECHO Dealers
refer to WWW.ECHO-USA.COM or call 1-800-432-ECHO.
OWNER’S RESPONSIBILITY
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at WWW.ECHO-USA.COMꢀRUꢀE\ꢀ¿OO-
LQJꢀRXWꢀWKHꢀZDUUDQW\ꢀUHJLVWUDWLRQꢀFDUGꢀVXSSOLHGꢀZLWKꢀ\RXUꢀXQLWꢁꢀ5HJLVWHULQJꢀ\RXUꢀSURGXFWꢀFRQ¿UPVꢀ\RXUꢀZDUUDQW\ꢀFRYHUDJHꢀDQGꢀSURYLGHVꢀDꢀGLUHFWꢀ
OLQNꢀLIꢀZHꢀ¿QGꢀLWꢀQHFHVVDU\ꢀWRꢀFRQWDFWꢀ\RXꢁ
The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in the
RSHUDWRU¶VꢀPDQXDOꢁꢀ6KRXOGꢀDꢀSURGXFWꢀGLI¿FXOW\ꢀRFFXUꢂꢀ\RXꢀPXVWꢂꢀDWꢀ\RXUꢀH[SHQVHꢂꢀGHOLYHUꢀRUꢀVKLSꢀ\RXUꢀ(&+2ꢀXQLWꢀWRꢀDQꢀDXWKRUL]HGꢀ(&+2ꢀVHUYLFLQJꢀ
dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit after the repairs have been
made. For your nearest authorized ECHO servicing dealer, call ECHO’s Dealer Referral Center, at 1-800-432-ECHO or you can locate an ECHO
servicing dealer at WWW.ECHO-USA.COM. Should you require assistance or have questions concerning ECHO’s Warranty Statement, you
can contact our Consumer Product Support Department at 1-800-673-1558 or contact us through the web at WWW.ECHO-USA.COM.
PRODUCT WARRANTY PERIOD
HOMEOWNER APPLICATION
•
5 YEAR WARRANTY - All units for homeowner, or non-income producing use will be covered by this limited warranty for ¿YH ꢀꢁꢂꢃ\HDUV from
date of purchase.
EXCEPTIONS:
‡ꢀ )RUꢀWZRꢃVWURNHꢀHQJLQHꢀSRZHUHGꢀSURGXFWVꢂꢀWKHꢀHOHFWURQLFꢀLJQLWLRQꢀPRGXOHꢂꢀÀH[LEOHꢀGULYHꢀFDEOHVꢂꢀ650ꢀVROLGꢀGULYHꢀVKDIWVꢂꢀDQGꢀ7&ꢀWLQHVꢀ
are warranted for the OLIHꢄ of the product on parts only.
•
Cutting attachments such as, but not limited to, bars, chains, sprockets, blades, and nylon trimmer heads for homeowner or non-
income producing use will be covered for failures due to defects in material or workmanship for a period of ꢅꢆꢃGD\V from original
product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty.
ECHO’s Rapid Loader String Head carries a lifetime warranty on the line locking system, parts only; no labor. Refer to your operator’s
manual for string head installation and maintenance instructions.
•
•
All SB-Series and PRO ATTACHMENT SERIES Split Shaft attachments carry the same warranty duration as the units they are
GHVLJQHGꢀWRꢀ¿Wꢁ
COMMERCIAL APPLICATION
•
1 YEAR WARRANTY - All Chain Saws, QuikVent Saws, and Cut-Off Saws for commercial, institutional, agricultural, industrial, or income
producing use will be covered by this limited warranty for one ꢀꢇꢂꢃ\HDU from the date of purchase.
2 YEAR WARRANTY - All other units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this
limited warranty for two ꢀꢈꢂꢃ\HDUV from the date of purchase.
•
EXCEPTIONS:
‡ꢀ )RUꢀWZRꢃVWURNHꢀHQJLQHꢀSRZHUHGꢀSURGXFWVꢂꢀWKHꢀHOHFWURQLFꢀLJQLWLRQꢀPRGXOHꢂꢀÀH[LEOHꢀGULYHꢀFDEOHVꢂꢀ650ꢀVROLGꢀGULYHꢀVKDIWVꢀDQGꢀ7&ꢀWLQHVꢂꢀ
are warranted for the OLIHꢄ of the product on parts only.
•
Cutting attachments such as, but not limited to, bars, chains, sprockets, blades, and nylon trimmer heads for commercial, institutional,
agricultural, industrial, rental, or income producing will be covered for failures due to defects in material or workmanship for a period
of ꢉꢆꢃGD\V from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by
this warranty.
•
•
ECHO’s Rapid Loader String Head carries a lifetime warranty on the line locking system, parts only; no labor. Refer to your operator’s
manual for string head installation and maintenance instructions.
All SB-Series and PRO ATTACHMENT SERIES Split Shaft attachments carry the same warranty duration as the units they are
GHVLJQHGꢀWRꢀ¿Wꢁ
RENTAL APPLICATION - 90 DAYS WARRANTY
• Units for rental use will be covered against defects in material and workmanship for a period of 90 days from the date of purchase.
ꢄꢀꢀ (&+2¶VꢀOLDELOLW\ꢀXQGHUꢀWKHꢀ³/LIHWLPH´ꢀFRYHUDJHꢀLVꢀOLPLWHGꢀWRꢀIXUQLVKLQJꢀSDUWVꢀVSHFL¿HGꢀXQGHUꢀWKHꢀPRODUCT WARRANTY PERIOD section of
this warranty statement for ³/LIH´ꢀIUHHꢀRIꢀFKDUJHꢀIRUꢀDꢀSHULRGꢀRIꢀWHQꢀꢄꢅꢆꢇꢀ\HDUVꢀDIWHUꢀWKHꢀGDWHꢀRIꢀWKHꢀFRPSOHWHꢀXQLW¶Vꢀ¿QDOꢀSURGXFWLRQꢁꢀ
32
X7502026704
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SHC-266
WARRANTY STATEMENTS
ECHO does not offer an over the counter exchange program. Any ECHO product re-built other than by ECHO or sold through an unauthorized
dealer, or an unauthorized outlet store, is sold without ECHO’s limited warranty coverage. The ECHO Limited Warranty coverage is extended
to the original purchaser only, and is not transferable except for emission related parts. Repair parts and accessories replaced under this
warranty are warranted only for the balance of the original unit or accessory warranty period. Any damage caused by improper installation or
improper maintenance is not covered by this warranty. All parts or products replaced under warranty become the property of ECHO.
PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES
• 90-day homeowner, or non-income producing warranty
• 30-day commercial, institutional, agricultural, industrial, income producing, or rental application warranty
ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS
This ECHO two-stroke engine power product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior
performance. To help ensure the performance of the unit, it is required to use two-stroke oil which meets the ISO-L-EGD Standard per ISO/CD
13738 and JASO M345FD Standards. (&+2ꢃ3RZHUꢃ%OHQGŒꢃ7ZRꢊ6WURNHꢃ2LO LVꢀDꢀSUHPLXPꢀWZRꢃVWURNHꢀRLOꢀVSHFL¿FDOO\ꢀIRUPXODWHGꢀWRꢀPHHWꢀ,62ꢃ
L-EGD (ISO/CD 13738) and JASO M345FD Standards. The use of two-stroke oils designed for other applications, such as for outboard motors
or lawnmowers can result in severe engine damage, and will void your two-stroke engine limited warranty.
THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY:
•
Lack of lubrication or engine failure, due to the use of two-stroke oils that do not meet the ISO-L-EGD (ISO/CD 13738) and JASO M345FD
Standards. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD compliant and JASO M345FD registered
oil, will void the two-stroke engine limited warranty. ECHO Power Blend™ Two-Stroke Oil meets the ISO-L-EGD and JASO M345FD
Standard. Emission related parts are covered for 5 years homeowner use or 2 years commercial use regardless of two-stroke oil used, per
the statement listed in the EPA or California Emission Defect Warranty Explanation.
Damage caused by use of gasohol, containing methanol (wood alcohol), or gasoline containing less than 89 octane. Only use gasoline which
contains 89 octane or higher. Gasohol which contains a PD[LPXP 10% ethanol (grain alcohol) or 15% MTBE (methyl/tertiary/butyl/ether)
is also approved. The prescribed mixing ratio of gasoline to oil is listed on the ECHO oil label and covered in your operator’s manual.
(QJLQHꢀGDPDJHꢀFDXVHGꢀE\ꢀXVHꢀRIꢀHWKHUꢀRUꢀDQ\ꢀVWDUWLQJꢀÀXLGVꢁꢀꢀ
'DPDJHꢀFDXVHGꢀE\ꢀWDPSHULQJꢀZLWKꢀHQJLQHꢀVSHHGꢀJRYHUQRUꢀRUꢀHPLVVLRQꢀFRPSRQHQWVꢂꢀRUꢀUXQQLQJꢀHQJLQHVꢀDERYHꢀVSHFL¿HGꢀDQGꢀUHFRPPHQGHGꢀ
engine speeds as listed in your operator’s manual.
•
‡ꢀ
‡ꢀ
‡ꢀ
•
‡ꢀ
2SHUDWLRQꢀRIꢀWKHꢀXQLWꢀZLWKꢀLPSURSHUO\ꢀPDLQWDLQHGꢈUHPRYHGꢀFXWWLQJꢀVKLHOGꢀRUꢀUHPRYHGꢈGDPDJHGꢀDLUꢀ¿OWHUꢁꢀꢀ
Damage caused by dirt, pressure or steam cleaning the unit, salt water, corrosion, rust, varnish, abrasives, and moisture.
'HIHFWVꢂꢀPDOIXQFWLRQVꢀRUꢀIDLOXUHVꢀUHVXOWLQJꢀIURPꢀDEXVHꢂꢀPLVXVHꢂꢀQHJOHFWꢂꢀPRGL¿FDWLRQVꢂꢀDOWHUDWLRQVꢂꢀQRUPDOꢀZHDUꢂꢀLPSURSHUꢀVHUYLFLQJꢂꢀRUꢀXVHꢀ
of unauthorized attachments.
•
•
Incorrect storage procedures, stale fuel, including failure to provide or perform required maintenance services as prescribed in the operator's
manual. Preventative maintenance as outlined in the operators manual is the customer’s responsibility.
Failures due to improper set-up, pre-delivery service or repair service by anyone other than authorized ECHO servicing dealer during the
warranty period.
Certain parts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups.
Use of spark plugs other than those meeting performance and durability requirements of the OEM spark plug listed in the Operator's
Manuals.
Overheating or carbon scoring failures due to restricted, clogged exhaust port or combustion chamber, including damage to spark arrester
screen.
•
•
•
‡ꢀ
•
$GMXVWPHQWVꢀDIWHUꢀWKHꢀ¿UVWꢀꢄꢉꢆꢇꢀWKLUW\ꢀGD\VꢀDQGꢀEH\RQGꢂꢀVXFKꢀDVꢀFDUEXUHWRUꢀDGMXVWPHQWꢀDQGꢀWKURWWOHꢀFDEOHꢀDGMXVWPHQWꢁꢀ
Damage to gears or gear cases caused by contaminated grease or oil, use of incorrect type or viscosity of lubricants, and/or failure to comply
with recommended grease or oil change intervals.
•
‡ꢀ
•
Damage caused by loading SHRED 'N' VAC® beyond recommended capacity.
'DPDJHꢀFDXVHGꢀE\ꢀSXPSꢀRUꢀVSUD\HUꢀUXQQLQJꢀGU\ꢂꢀSXPSLQJꢀRUꢀVSUD\LQJꢀFDXVWLFꢀRUꢀÀDPPDEOHꢀPDWHULDOVꢂꢀRUꢀODFNꢀRIꢀRUꢀEURNHQꢀVWUDLQHUVꢁꢀ
Additional damage to parts or components due to continued use after operational problem or failure occurs. Should operational problem or
failure occur, the product should not be used, but delivered as is to an authorized ECHO servicing dealer.
It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your ECHO product or by visiting
WWW.ECHO-USA.COM. Your receipt of purchase including date, model and serial number must be maintained and presented to an authorized
ECHO servicing dealer for warranty service. Proof of purchase rests solely with the customer. Some states do not allow limitations on how long
an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the exclusion or limitation of incidental or
FRQVHTXHQWLDOꢀGDPDJHVꢂꢀVRꢀ\RXꢀPD\ꢀDOVRꢀKDYHꢀRWKHUꢀVSHFL¿FꢀOHJDOꢀULJKWVꢀZKLFKꢀYDU\ꢀIURPꢀVWDWHꢀWRꢀVWDWHꢁꢀ7KLVꢀOLPLWHGꢀZDUUDQW\ꢀLVꢀJLYHQꢀE\ꢀ(&+2ꢀ
Incorporated, 400 Oakwood Rd., Lake Zurich, IL 60047.
DISCLAIMER OF IMPLIED WARRANTIES
This limited warranty is in lieu of all other expressed or implied warranties, including any warranty of FITNESS FOR A PARTICULAR PURPOSE
OR USE and any implied warranty of MERCHANTABILITYꢀRWKHUZLVHꢀDSSOLFDEOHꢀWRꢀWKLVꢀSURGXFWꢁꢀ(&+2ꢀDQGꢀLWVꢀDI¿OLDWHGꢀFRPSDQLHVꢀVKDOOꢀQRWꢀEHꢀ
OLDEOHꢀIRUꢀDQ\ꢀVSHFLDOꢀLQFLGHQWDOꢀRUꢀFRQVHTXHQWLDOꢀGDPDJHꢂꢀLQFOXGLQJꢀORVWꢀSUR¿WVꢁꢀ7KHUHꢀDUHꢀQRꢀZDUUDQWLHVꢀH[WHQGHGꢀRWKHUꢀWKDQꢀDVꢀSURYLGHGꢀKHUHLQꢁꢀ
7KLVꢀOLPLWHGꢀZDUUDQW\ꢀPD\ꢀEHꢀPRGL¿HGꢀRQO\ꢀE\ꢀ(&+2ꢁ
99922201032
11/18/2011
X7502026704
33
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
SHC-266
NOTES
34
X7502026704
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SHC-266
PRODUCT REGISTRATION
PRODUCT REGISTRATION
Thank you for choosing ECHO Power Equipment
and EASY! NOTE: your information will never be sold or misused by ECHO, Inc. Registering your purchase enables us
to contact you in the unlikely event of a service update or product recall, and verifies your ownership for warranty
consideration.
If you do not have access to the Internet, you can complete the form below and mail to:
ECHO Inc., Product Registration, PO Box 1139, Lake Zurich IL 60047.
X7502026704
35
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
SHC-266
NOTES
36
X7502026704
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SHC-266
NOTES
X7502026704
37
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
SHC-266
38
X7502026704
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SHC-266
NOTES
X7502026704
39
© 10/2014 ECHO Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
T43911001001/T43911999999
T44012001001/T44012999999
40
Download from Www.Somanuals.com. All Manuals Search And Download.
|
