PAS Articulating Hedge Clipper Attachment
Operator's Manual
MODEL
99944200595
FOR MODELS:
SRM-2100SB/2400SB
SRM-210SB/211SB
SRM-225SB
SRM-260SB/261SB
PAS-2100/2400
PAS-210/211
PAS-230/231
PAS-260/261
PAS-2601
PAS-265
WARNING
Read rules for safe operation and instructions carefully. ECHO provides an
Operator's Manual and a Safety Manual for Pro Attachment Series power source or
Split Boom Trimmer. Those manuals and this manual must be read and understood
for proper and safe operation, otherwise serious personal injury may result.
X753001923
01/09
X7532095603
Download from Www.Somanuals.com. All Manuals Search And Download.
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
3
SAFETY
MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION
Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages
preceded by symbols or key words. The following is an explanation of those symbols and key words and what they
mean to you.
CIRCLEANDSLASHSYMBOL
DANGER
The safety alert symbol accompanied by the
word “DANGER” calls attention to an act or
condition which WILL lead to serious personal
injury or death if not avoided.
This symbol means the specific action
shown is prohibited. Ignoring these
prohibitions can result in serious or fatal
injury.
NOTE
WARNING
The safety alert symbol accompanied by the
word “WARNING” calls attention to an act or
condition which CAN lead to serious personal
injury or death if not avoided.
This enclosed message provides tips for use, care
and maintenance of the unit.
IMPORTANT
The enclosed message provides information neces-
sary for the protection of the unit.
CAUTION
The safety alert symbol accompanied by the
word “CAUTION” calls attention to an act or
condition which may lead to minor or moderate
personal injury if not avoided.
INTERNATIONAL SYMBOLS
Symbol
description/application
Symbol
description/application
Symbol
description/application
Symbol
description/application
Symbol form/shape
Symbol form/shape
Symbol form/shape
Symbol form/shape
Planretreatpath
from falling
objects.
Readand
understand
Operator'sManual.
Fuel and oil
mixture
Emergencystop
Choke Control
"Cold Start"
Position
FingerSevering
Weareyes,ears
andhead
protection
Wear slip
resistant foot
wear.
(Choke Closed)
Wear hand
protection.Use
twohanded.
Choke Control
"Run"
Position
Hot
Surface
Ignition
ON/OFF
(ChokeOpen)
DO NOT smoke
nearfuel.
Carburetor
adjustment
- High speed
mixture
Safety/Alert
Primerbulb
Avoidallpower
lines. This unit is
not insulated
againstelectrical
current.
DONOTallow
flamesorsparks
nearfuel.
Carburetor
adjustment
-Lowspeed
mixture
Carburetor
adjustment
-Idlespeed
Do not operate
closer than 15 M
(50 ft.) from
electrical
Keepbystanders
atleast15meters
(50feet)away.
hazards.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
PERSONAL CONDITION AND SAFETY EQUIPMENT
WARNING
Users of this product risk injury to themselves and others if the unit is used improperly and/or safety precautions
are not followed. Proper clothing and safety gear must be worn when operating unit.
Physical Condition
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
• if you are taking medication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection
Wear eye protection that meets ANSI Z87.1 or CE requirements whenever you operate the unit.
Hand Protection
Wear no-slip, heavy-duty work gloves to improve your grip on the handle. Gloves also reduce the transmission of
machine vibration to your hands.
Hearing Protection
ECHO recommends wearing hearing protection whenever unit is used.
Proper Clothing
Wear snug fitting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DONOTWEARSHORTS,
• DONOTWEARTIES,SCARFS,JEWELRY.
Wear protective hair covering to contain long hair.
Wear sturdy work shoes with nonskid soles;
• DONOTWEAROPENTOEDSHOES,
• DONOTOPERATEUNITBAREFOOTED.
Keep long hair away from engine and air intake. Retain hair with cap or net.
Hot Humid Weather
Heavy protective clothing can increase operator fatigue which may lead to heat stroke. Schedule heavy work for early
morning or late afternoon hours when temperatures are cooler.
Extended Operation/Extreme Conditions
It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals, may be
brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning
sensations, followed by loss of color and numbness in the fingers. The following precautions are strongly recom-
mended, because the minimum exposure, which might trigger the ailment, is unknown.
• Keep your body warm, especially the head, neck, feet, ankles,
hands, and wrists.
• Maintain good blood circulation by performing vigorous arm
exercises during frequent work breaks, and also by not smoking.
• Limit the hours of operation. Try to fill each day with jobs where
operating the unit or other hand-held power equipment is not
required.
• If you experience discomfort, redness, and swelling of the fingers
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.
Download from Www.Somanuals.com. All Manuals Search And Download.
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
5
Repetitive Stress Injuries
It is believed that overusing the muscles and tendons of the fingers, hands, arms, and shoulders may cause soreness,
swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high
risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which
could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged
exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years.
To reduce the risk of RSI/CTS, do the following:
• Avoid using your wrist in a bent, extended, or twisted position.
Instead try to maintain a straight wrist position. Also, when
grasping, use your whole hand, not just the thumb and index finger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive
movement.
• Do exercise to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if
you feel tingling, numbness, or pain in the fingers, hands, wrists, or
arms. The sooner RSI/CTS is diagnosed, the more likely permanent
nerve and muscle damage can be prevented.
DANGER
Do not operate this product indoors or in inadequately ventilated
areas. Engine exhaust contains poisonous emissions and can
cause serious injury or death.
Read the Manuals
• Provide all users of this equipment with the Operator’s Manual and
Safety Manual for instructions on Safe Operation.
Clear the Work Area
• Spectators and fellow workers must be warned, and children and
animals prevented from coming nearer than 15 m (50 ft.) while the
unit is in use.
Keep a Firm Grip
• Hold the front and rear handles with both hands, with thumbs and
fingers encircling the handles.
Keep a Solid Stance
• Maintain footing and balance at all times. Do not stand on slippery,
uneven or unstable surfaces. Do not work in odd positions or on
ladders. Do not over reach.
Cutting Angle Adjustments
• Only adjust cutting blade angle with unit flat on the ground, with the
engine stop switch in the “STOP” position. Never adjust cutting
angle with unit standing upright.
Avoid Hot Surfaces
• Keep exhaust area clear of flammable debris. Avoid contact during
and immediately after operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
EQUIPMENT
WARNING
Use only ECHO approved attachments. Serious injury may result from the use of a non approved attachment
combination. Read and comply with all safety instructions listed in this manual and safety manual. ECHO, INC. will
not be responsible for the failure of cutting devices or accessories which have not been tested and approved by
ECHO for use with this unit.
• Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.
• Never adjust blades when the engine is operating.
• Inspect hand guard for damage. Replace if damaged or missing.
• Check that the blade assembly is firmly attached and in safe operating condition. Dull, loose or damaged blades
should not be used.
WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings.
• ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop
before removing obstructions, clearing debris, or servicing unit.
• DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.
• NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings.
DESCRIPTION
Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the
instructions on them. If a decal cannot be read, a new one can be ordered from your ECHO Dealer. See PARTS ORDER-
3
INGinstructionsforspecificinformation.
8
Shaft Decal
P/NX505000531
4
5
2
P/N 89016012360
1
6
7
P/N 89017854331
Download from Www.Somanuals.com. All Manuals Search And Download.
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
7
1. CUTTING BLADES - Double reciprocating blades mounted to a blade support bar. Double sided blades, are capable
of cutting on either side of the blade.
2. LOWERDRIVESHAFTASSEMBLY-IncludestheGearHousingassembly,FlexibleDriveCable,BladeandSafety
Decals.
3. FLEXIBLEDRIVECABLE-Cableendfitsintoupperdriveshaftcoupler. Lubricatedrivecableevery25hourswith
ECHO® LUBETM grease.
4. FRONTDRIVESHAFTGRIP-Cushionedhandgripforgrippingdriveshaftassembly.
5. HAND GUARD / BLADE LOCK - Locks blade in place for travel / storage. Always assure blade cover is installed
when locking blade.
6. BLADEADJUSTMENTHANDLE-Providessecurehandgripforadjustingcuttingbladeangle.
7. BLADE INDEXING RING- Pull ring out and turn 1/4 turn to lockout position when adjusting blade angle.
8. BLADE COVER - Used to cover blades during transport and storage. Remove blade cover before operating unit.
CONTENTS
The ECHO product you have purchased has been factory pre-assembled for your convenience.
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts.
Use the contents list to check for missing parts.
_____ 1 - Articulating Hedge Clipper Attachment
_____ 1 - Operator's Manual
_____ 1 - Hedge Clipper Safety Manual
_____ 1 - Warranty Registration Card
_____ 1 - Blade Cover
_____ 1 - Storage Hook Assembly
Download from Www.Somanuals.com. All Manuals Search And Download.
8
ASSEMBLY
POWER HEAD SHAFT/LOWER SHAFT ASSEMBLY
Tools Required: None
Parts Required: PAS or SRM-SB Power Head w/Shaft & Coupling.
B
1. Set Power Head/Shaft Assembly on a level surface.
D
2. Pull locator pin (A) out, and turn counter-clockwise 1/4 turn to lock-
out position.
E
3. Remove vinyl cap from attachment drive shaft.
C
4. Carefully fit attachment drive shaft assembly into coupler (B) to
decal assembly line (C), making sure that the inner lower drive shaft
engages into the square upper drive shaft socket.
A
NOTE
Earlier model Power Heads may have shorter couplings. Short
couplings fit flush to decal point (E). New couplings are 4-3/4 in.
long, and fit flush to line (C).
D
C
5. Rotate locator pin (A) 1/4 turn clockwise to engage lower shaft
hole. Insure locator pin is fully engaged by twisting lower drive
shaft. Locator pin should snap flush in coupler. Full engagement
will prevent further shaft rotation.
6. Secure lower shaft assembly to coupler by tightening clamping
knob(D).
A
Download from Www.Somanuals.com. All Manuals Search And Download.
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
9
OPERATION
WARNING
All over head electrical conductors and communications wires can have electricity flow with high voltages. Never
touch wires directly or indirectly when pruning, otherwise serious injury or death may result.
ADJUSTING CUTTING ANGLE
WARNING
Never adjust cutting assembly with engine running.
WARNING
A
Hedge clipper blades are sharp. Always wear gloves when
adjusting cutting assembly, otherwise serious injury may result.
WARNING
DO NOT stand hedge clipper on end when adjusting cutting angle,
otherwise serious injury may result
1. Place unit on a flat clear area. Assure stop switch is in the “STOP”
position.
2. Pull out indexing ring (A), and turn ¼ turn to lockout position.
B
3. Turn hedge clipper ¼ turn so that indexing ring faces downward.
4. Release hand-guard blade lock (B) with right hand, while holding
blade-adjustment handle (C) with left hand.
5. Rotate blades to desired cutting position and hold in place.
6. Turn indexing ring ¼ turn to lock blade in place.
WARNING
B
Gear case assembly becomes HOT during use. Always grip
assembly at blade-adjustment handle when making cutting angle
adjustments, otherwise serious injury may result.
IMPORTANT
C
Always install blade cover, and return cutting assembly to folded/
locked position for travel/storage.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
ROTATE CUTTER ASSEMBLY
Always use the unit from the right-hand side of your body – NEVER
from the left side. Rotate cutter assembly 180 degrees on driveshaft in
order to avoid cutting directly above your head, and to avoid contact
withhotmuffler.
1. Loosen gearcase clamping screw (A), hand guard clamping screw
(B), and remove gearcase locating screw (C).
B
2. Rotate cutter assembly 180-degrees on driveshaft until locating
hole in driveshaft is visible through locating hole in gearcase.
3. Install gearcase locating screw (C), and securely tighten all
hardware.
C
A
WARNING
During operation, the complete unit, especially the drive shaft
housing and gearcase may become too hot to touch. Avoid
contact when rotating cutter assembly.
HEDGE TRIMMING
1. Always grip throttle handle with right hand and support handle
with left hand while trimming.
2. Hold trimmer firmly and squeeze throttle trigger to accelerate
engine.
3. Tilt trimmer so cutting teeth are angled slightly toward the hedge
or shrub and proceed to cut.
WARNING
Never remove hands from unit when blades are moving.
WARNING
The engine continues running even when the blades have stopped
due to an obstruction. If this occurs, stop the engine, disconnect
ignition cable and remove the obstruction.
Download from Www.Somanuals.com. All Manuals Search And Download.
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
11
MAINTENANCE
WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete
stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing
service. Wear gloves to protect hands from sharp edges and hot surfaces.
Your ECHO trimmer is designed to provide many hours of trouble free service. Regular scheduled maintenance will
help your trimmer achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to
take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOUR-
SELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed see your ECHO
dealer for repairs.
SKILL LEVEL
Level 1 = Easy to do. Common tools may be required.
Level 2 = Moderate difficulty. Some specialized tools may be required.
MAINTENANCE INTERVALS
Component/System
Maintenance Procedure
Skill Level
Frequency
CuttingBlades
DriveShaft
GearHousing
Screws/Nuts/Bolts
Oil/Clean
Grease
Grease
Inspect/Tighten/Replace
1
1
1
1
Before each use
Every 25 hours of use
Every 15-25 hours of use
Before each use
LUBRICATION
Blades
Level1
Tools Required: Clean rag, brush, oil can
Parts Required: 20WEngineOil(lubrication),50-50mixtureof
kerosene and 20W oil (cleaning).
WARNING
Blades are very sharp. Wear gloves to protect hands, otherwise
serious personal injury may result.
1. Brush loose debris from blade and coat both sides of blade with the
50-50cleaningmixture.
2. Allowcleaningmixturetosoftentheremaininggummyresiduethenwipeit
fromtheblade.
3. Applycleanoiltotheentirelengthoftheblade. Becertainthebladebolts
arelubricated.
4. Wipeexcessoilfromthebladebeforeputtingtheunitbackinservice.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Gear Housing
Level 1.
Tools required: Grease Gun, Rag.
Parts required: POWER BLENDXTM 14 oz. Cartridge P/N 91015
Grease or Lithium-based Grease.
1. Clean dirt from grease fittings (A).
2. Carefully pump grease in each fitting. DO NOT force grease.
Too much pressure will force grease past seals and cause damage.
Apply 1-2 pumps of grease every 15-25 hours of operation.
A
A
Lower Drive Shaft Assembly
Level1
NOTE
Drive shaft should be greased every 25 hours of operation.
Tools required: 4 mm hex wrench, 8mm open end wrench, clean rag,
small brush.
Parts required: POWER BLENDXTM 14 oz. cartridge P/N 91015 or
Lithium-based Grease.
WARNING
Blades are very sharp. Wear gloves to protect hands, otherwise
serious personal injury may result.
D
A
B
1. Carefully remove locating screw (A) and loosen clamping screw (B).
Remove the flex drive shaft assembly from the gear housing.
2. Pull the drive shaft (C) from the drive shaft assembly, and wipe
clean. Re-coat with a thin coating [1/2 oz. (15 ml)] of grease.
3. Slide the flex shaft back into the drive shaft assembly, being careful
not to get dirt on the flex shaft.
C
4. Align the locating screw hole in gear case with the locating hole in
drive shaft assembly, install and tighten locating screw (A), and
tighten clamping screw (B).
IMPORTANT
Flat edge of washer (D) must be against drive shaft.
Download from Www.Somanuals.com. All Manuals Search And Download.
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
13
SHARPENING BLADES
Level3.
Tools required: Flat file,screwdriver
Parts required: None
WARNING
Hedge Clipper Blades are very sharp. Wear gloves to protect
hands.
1. Disconnect spark plug wire from spark plug.
2. Slide blades to allow file clearance using slots (A) on bottom of
blades. Do not pry against cutting edges.
3. Follow the original shape, and file each cutting edge carefully to
avoid damage to adjacent teeth. Maintain 6 mm (.25 in.) radius at
base of each tooth.
A
A
6mm (.25 in.) Radius
IMPORTANT
If a power grinder is used, DO NOT allow blade to over heat.
45º
4. Lubricate blades. See "Lubrication."
5. Connect spark plug wire.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
BLADE ADJUSTMENT
Level 2.
Tools required: (2) 10 mm Sockets & Extensions
Parts required: None
WARNING
Hedge clipper blades are very sharp. Touching them may lead to
severe personal injury. Use a socket and extension when adjust-
ing blade bolts or blade locknuts in order to keep hands at a safe
distance from sharp blades.
1. Tighten blade bolts (A) until snug, then loosen blade bolts 1/2
turn.
2. Hold blade bolts (A) from turning using 10 mm socket & Exten-
sion, and tighten blade lock nuts (B) with other 10 mm Socket &
Extension.
B
NOTE
A
Locking ability of Hedge Clipper blade lock nuts will diminish
each time they are removed. Replace if turning resistance is not
felt when installing locknuts.
Download from Www.Somanuals.com. All Manuals Search And Download.
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
15
STORAGE
IMPORTANT
Always store and transport hedge clippers in a stable position.
Support gear case and cutting blades to prevent excessive flexing
which may cause damage to the cutting attachment. Always
install blade cover when transporting or storing unit.
1. Clean and lubricate cutting blades and gear case.
2. Sharpen cutting blades as required.
3. Apply a light coating of clean 20W engine oil along entire length of
blades and on blade bolts.
4. Install blade cover onto hedge clipper cutting blades.
5. Store hedge clipper attachment in a dry, dust free place out of the
reach of children, using supplied storage hook.
Storage Hook Installation
1. Insert small end of hook into locating hole on attachment shaft.
2. Slide plastic cap onto end of attachment shaft.
SPECIFICATIONS
PAS Articulating Hedge Clipper Attachment
Length ------------------------------------------------------- 1016mm(40.0in.)
Attachment Width ----------------------------------------- 132mm(5.2in.)
Height ------------------------------------------------------- 127mm(5.0in.)
Weight ------------------------------------------------------ 2.76kg.(6.08lb.)
GearCaseRatio -------------------------------------------- 4.072:1
Cutter -------------------------------------------------------- Double Reciprocating Blade - Double Edge
Effective Length ----------------------------------------- 464mm(18.3in.)
Pitch ------------------------------------------------------- 35mm(1.4in.)
MaximumDiameterCut
Soft Material ---------------------------------------------- 25.4mm(1in.)
Woody Material ------------------------------------------ 13mm(1/2in.)
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING INFORMATION
PARTS/SERIAL NUMBER
GenuineECHOPartsandECHOREPOWER™PartsandAssembliesfor
your ECHO products are available only from an Authorized ECHO
Dealer. When you do need to buy parts always have the Model
Number and Serial Number of the unit with you. You can find these
numbers on the engine housing. For future reference, write them in the
space provided below.
Model No. _____________ SN. ____________
SERVICE
Service of this product during the warranty period must be performed
by an Authorized ECHO Service Dealer. For the name and address of
the Authorized ECHO Service Dealer nearest you, ask your retailer or
call:1-800-432-ECHO(3246). Dealerinformationisalsoavailableonour
Web Site. When presenting your unit for Warranty service/repairs,
proof of purchase is required.
DEALER?
Call
1-800-432-ECHO
or
ECHO CONSUMER PRODUCT SUPPORT
If you require assistance or have questions concerning the application,
operation or maintenance of this product you may call the ECHO
ConsumerProductSupportDepartmentat1-800-673-1558from8:30am
to 4:30 pm (Central Standard Time) Monday through Friday. Before
calling, please know the model and serial number of your unit to help
your Consumer Product Support Representative.
CONSUMER PRODUCT
SUPPORT
1-800-673-1558
8:30 - 4:30 Mon - Fri C.S.T.
WARRANTY REGISTRATION
You may register your Echo equipment using the warranty registration
direct link between you and ECHO if we find it necessary to contact
you.
ADDITIONAL OR REPLACEMENT MANUALS
Safety Manuals in English/Spanish or English/French are available, free of charge, from your ECHO dealer or at
Operator'sandPartsManualsareavailableby:
• Downloadingfreefromwww.echo-usa.com
• Purchasing from your Echo Dealer.
• Manuals are available by sending a written request stating the model number and serial number of your Echo unit,
part number of the manual, your name and address, and mail to the address below.
Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.
ECHO, INCORPORATED
400 OAKWOOD ROAD
LAKE ZURICH, IL 60047-1564
S06700001001/S06700999999
Download from Www.Somanuals.com. All Manuals Search And Download.
|