Pro Trashbreaker
Owner’s Manual
March 2014
190-01726-00_0B
Printed in Taiwan
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching the Dog Collar Device to the Collar
Strap
Getting Started
WARNING
With the buckle facing outward, insert the end of the collar
1
À
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
strap through the slot on the collar device.
Á
Setting Up the Pro Trashbreaker System
Before you can use the Pro Trashbreaker system, you must set
up the devices.
Attach the dog collar device to the collar strap (Attaching the
1
Charge the handheld device (Charging the Handheld
Device).
2
3
4
5
Pull most of the collar strap through the two slots on the
dog device.
2
3
Â
If necessary, pair the dog collar device with the handheld
Device).
Insert the end of the collar strap through the slot on the
Ã
opposite side of the device.
Pull the strap until it is tight across the front of the device.
4
5
6
Device Overviews
Wrap the antenna keeper around the collar strap.
Ä
Pro Trashbreaker Handheld Device
NOTE: Do not bend the antenna sharply. You should
lengthen the collar strap on the side with the antenna keeper
to avoid bending the antenna sharply.
Slide the antenna through the antenna keeper.
Å
Charging the Handheld Device
You should fully charge the battery before you use the device
for the first time or whenever the battery is low (Checking the
Battery Level). It is normal for the battery to discharge in
approximately 7 to 10 weeks when the device is not in use.
Charging a fully depleted battery takes about 2 hours.
NOTE: The device will not charge when it is outside the
temperature range of 32° to 104°F (0° to 40°C).
Lift the weather cap
.
1
À
Intensity level and training mode dial
Battery level
À
Á
Â
Ã
Dog collar device toggle switch
Training keys
Pro Trashbreaker Dog Device
Plug the small end of the power cable into the mini-USB port
2
3
on the device.
Á
Plug the other end of the power cable into an appropriate
power source.
The status LED is solid red when the device is charging.
Power key
À
Á
Â
Ã
Ä
After the status LED turns solid green, unplug the power
cable from the device.
4
Status LED
Lights
Contact points
Charging clip contacts
Getting Started
1
Download from Www.Somanuals.com. All Manuals Search And Download.
On the handheld device, move the toggle switch and select a
key to choose the color associated with the dog collar
device.
1
Charging the Collar
NOTICE
To prevent corrosion, thoroughly dry the contacts on the collar
and the surrounding area before connecting the charging clip.
On the handheld device, set the intensity level to a
2
3
4
On the dog collar device, hold the power key for about 5
seconds until the status LED changes to yellow.
You should fully charge the battery before you use the device
for the first time or whenever the battery is low (Checking the
Battery Level). It is normal for the battery to discharge in
approximately 7 to 10 weeks when the device is not in use.
Charging a fully depleted battery takes about 2 hours.
On the handheld device, select a training key.
The dog collar device beeps when the devices have paired
successfully. If the device does not beep, pairing has not been
successful.
NOTE: The device will not charge when outside the
temperature range of 32° to 104°F (0° to 40°C).
TIP: If the devices did not pair successfully, you should verify
the batteries in both devices are fully charged and the intensity
level is set to a numbered position.
Snap the charging clip onto the device
.
Á
1
À
Selecting a Dog Collar Device
Before you can select and control a dog collar device, you must
pair the dog collar device with the handheld device (Pairing a
Select the color associated with a dog collar device:
•
•
•
To select the button color, move the dog collar device
toggle switch up.
To select the inner ring color, move the toggle switch to
the middle position.
To select the outer ring color, move the toggle switch
down.
The training keys control the dog collar device associated with
the selected color.
Plug the power cable into a power source.
2
3
The status LED is solid red when the collar is charging.
After the status LED turns solid green, remove the charging
clip from the collar.
Dog Training
You should research and investigate the training methods best
suited for you, your dog, and your needs.
Turning On the Dog Collar Device
•
•
•
On the dog collar device, hold the power key until the status
LED turns green and the collar beeps to turn it on in training
mode.
When used properly, the Pro Trashbreaker training system is an
effective training tool to aid your dog in reaching its full potential.
The use of the training system should be part of an overall
training program.
On the dog collar device, hold the power key until the status
LED turns blue to turn on the BarkLimiter™ feature
Fitting the Collar on Your Dog
On the dog collar device, hold the power key until the status
LED turns yellow to enter pairing mode (Pairing a Dog Collar
CAUTION
To prevent irritation from the contact points, remove the collar
for at least eight hours out of every 24-hour period.
Turning Off the Device
This device is not intended for human use. Do not attempt to
use on any person.
On the dog collar device, hold the power key until the red
LED appears.
1
In order to properly correct the dog, the collar and device must
fit the dog properly. If the collar is too loose or positioned
incorrectly, corrections may be inconsistent. This can delay or
prevent successful training.
Release the power key.
2
The dog collar device beeps to confirm powering off.
NOTE: If the device is powered off in BarkLimiter mode, the
LED flashes the number of corrected barks before powering
Place the collar around the middle of the dog's neck.
1
2
Position the device at the front of the dog's neck, with the
status LED facing toward the dog's chin and the contact
points against the throat.
Dog Collar Device
You can use up to 9 dog collar devices with a single handheld
device.
Tighten the strap so that it is very snug around the dog's
neck, and fasten the buckle.
3
Each dog collar device must be paired with the handheld device
before it can be used. During the pairing process, each dog
collar device is associated with a different color on the handheld
device.
NOTE: The collar should fit tightly and should not be able to
rotate or slide on the dog's neck. The dog must be able to
swallow food and water normally. You should observe your
dog's behavior to verify the collar is not too tight.
Pairing a Dog Collar Device with the Handheld Device
NOTE: If your handheld device and dog collar device were
included in the same package, the devices are paired from the
factory.
2
Dog Training
Download from Www.Somanuals.com. All Manuals Search And Download.
Sometimes dogs will vocalize due to the surprise of the
electrical stimulation. If the dog vocalizes more than once,
the intensity level is too high for beginning training.
If there is no reaction, increase the intensity level by one
level until the dog has a slight but recognizable reaction to
the stimulation.
4
The intensity level that causes a slight but recognizable reaction
is your dog's baseline level for beginning collar training. You do
not need to, and should not, apply this intensity selection test
again.
After you begin training, the dog’s performance guides your
intensity selection. As the dog advances in training, you may
need to change the level depending upon the training situation.
Changing the Intensity Level
You can select a different intensity level for each dog collar
device.
1
2
Wiggle the device to work the contact points through the
dog's coat.
4
Adjust the intensity dial to increase or decrease the intensity
level.
NOTE: The contact points must have contact with the dog's
skin to be effective.
BarkLimiter
If the strap is too long, cut off the excess, leaving at least
3 in. (8 cm) to spare.
5
6
When the dog collar device is active and properly fitted on the
dog, it detects and corrects barks automatically. The dog collar
device starts at the lowest intensity level and increases the
intensity level gradually until the dog stops barking. When the
dog is quiet, the intensity decreases over time.
Mark the hole used to fasten the buckle for future reference
(optional).
MURS Radio Interference
If your handheld device experiences interference from another
transmitter, the LED flashes yellow when you press a training
key.
The status LED flashes briefly when the dog collar device
detects motion or corrects a bark.
Green, amber, or red Motion was detected, and no correction was
flash
applied.
Blue flash
A bark was detected, and a correction was
applied.
Selecting and Installing the Contact Points
For best results, select the correct contact points based on your
dog's coat.
NOTE: A green, amber, or red flash denotes how much charge
is left in the dog device battery, ranging from high to low.
Select the correct contact point length for your dog's coat
type:
1
Enabling the BarkLimiter Feature
On the dog collar device, hold the power key until the LED
flashes blue.
•
•
For dogs with thicker coats, use the longer contact points.
For dogs with shorter coats, use the shorter contact
points.
If necessary, use the included wrench to remove the contact
points.
2
Bark Odometer™
When you turn off the device, the LED flashes red and green to
report the number of times the device detected a bark since it
was last turned on. This can help you track your dog's barking
behavior.
Twist the contact points into the collar.
3
4
Tighten with the included wrench, but do not overtighten.
When you put the collar on the dog, make sure the contact
points are tight against the neck.
Red flash
10 barks
1 bark
Green flash
Training Intensities and Methods
You can use several methods to train your dog. The Pro
Trashbreaker system provides 6 stimulation intensity levels,
which increase sequentially from 1 to 6.
For example, one red flash followed by four green flashes
indicates the device detected 14 barks.
Zero flashes indicates the device detected zero barks.
Continuous stimulation: Applies stimulation to the dog the
entire time you press the training key, for a maximum of 8
seconds. Your stimulations should typically be much shorter
than 8 seconds.
Checking the Bark Odometer
Remove the device from the dog.
1
2
3
Position the device so that you can see the status LED.
Hold the power key until the status LED turns red, and
release.
Tone: Activates an audible tone instead of stimulation. A tone
can be used as either a positive or negative training cue,
depending on your training program.
Count the red and green flashes.
4
Choosing the Correct Intensity Level
Using the Light
You can use the light feature on your device to verify pairing,
help locate your dog, and provide safety for your dog at night.
Set the intensity to the lowest level (Changing the Intensity
Level).
1
Select a training key.
2
3
Rotate the intensity dial to L.
1
2
3
Observe the dog for a reaction, such as a head shake, neck
movement, or just a change in expression.
Select the training key.
Dog Training
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove the screw securing the VHF antenna to the back
plate.
3
4
5
Á
Device Information
Pull the length of the antenna from the antenna guide to
remove the old antenna.
Pro Trashbreaker Handheld Device
Specifications
Loop the antenna guide around the collar strap, and thread
the new VHF antenna through the guide.
Battery type
Rechargeable, replaceable lithium-ion
Battery life
60 hours typical use
This helps to point the antenna up.
Operating temperature range From -4° to 140°F (from -20° to 60°C)
Charging temperature range From 32° to 104°F (from 0° to 40°C)
Replace the screw securing the VHF antenna to the back
plate.
6
Storage temperature range
Water rating
From -4° to 104°F (from -20° to 40°C)
IEC 60529 IPX7*
Replace the cover over the VHF antenna.
Replace the three screws on the cover.
7
8
Wireless range
4 mi. (6.4 km)
Pro Trashbreaker Battery Replacement
Instructions
*The device withstands incidental exposure to water of up to
1 meter for up to 30 minutes.
WARNING
Pro Trashbreaker Dog Collar Device
Specifications
This product contains a lithium-ion battery. To prevent the
possibility of personal injury or product damage caused by
battery exposure to extreme heat, store the device out of direct
sunlight.
Battery type
Rechargeable, replaceable lithium-ion
Battery life
40 hours typical use
Operating temperature range
Charging temperature range
From -4° to 140°F (from -20° to 60°C)
From 32° to 104°F (from 0° to 40°C)
Do not use a sharp object to remove batteries.
CAUTION
Storage temperature range (up From -4° to 122°F (from -20° to 50°C)
to 1 month)
Contact your local waste disposal department to properly
recycle the batteries.
Storage temperature range (up From -4° to 95°F (from -20° to 35°C)
to 3 months)
Pro Trashbreaker Handheld Device Components
Water rating
Up to 1 ATM*
*The device withstands pressure equivalent to a depth of
10 meters.
Checking the Battery Level
Turn on the dog collar device (Turning On the Dog Collar
Device).
The status LED flashes every few seconds while the device is
on. The color of the status LED indicates the battery charge
level.
Green
Yellow
Red
The battery has a good charge.
The battery should be charged soon.
The battery is very low and should be charged
immediately.
Flashing Red The battery is depleted and must be charged. Training
features are disabled.
Security screws
Back plate
À
Á
Â
Ã
Ä
Å
Replacing the VHF Antenna in the Dog
Collar Device
Battery plate screws
Gasket
Before you replace the VHF antenna, you must remove all dirt,
water, and debris from the device. You also need a small
Phillips screwdriver and a larger Phillips screwdriver.
Battery plate
Battery
Remove the three screws from the cover over the VHF
1
À
antenna.
Replacing the Pro Trashbreaker Handheld Device
Battery
Before you replace the battery, you must remove all dirt, water,
and debris from the device. You also need a small Phillips
screwdriver and the security screwdriver included with the
battery replacement kit.
You can purchase a replacement battery at
http://buy.garmin.com. You should use only an official Garmin
replacement part.
®
Remove the eight security screws from the back of the
device.
1
Lift up the back plate.
2
3
Grip the battery connector wires close to the connector, and
pull the connector perpendicular to the circuit board to
disconnect the battery connector from the device.
Pry off the cover.
2
4
Device Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Grip the rotary switch connector wires close to the connector,
and pull the connector perpendicular to the circuit board to
disconnect the rotary switch connector from the device.
4
Gasket
Å
Æ
Front enclosure
Replacing the Battery Assembly
Remove the two screws from the battery plate.
Lift up the battery plate.
5
6
7
Before you replace the battery, you must remove all dirt, water,
and debris from the device. You also need a small Phillips
screwdriver and the security screwdriver included with the
battery replacement kit.
Remove the old battery from the back plate, noting the
orientation of the battery.
The battery fits tightly. It may be necessary to pry the battery
out of the back plate using a non-sharp, non-metal object.
You can purchase a replacement battery at
http://buy.garmin.com. You should use only an official Garmin
replacement part.
Install the new battery into the back plate with the label side
up, using the same orientation as the old battery.
8
Remove the three screws from the cover over the VHF
1
À
Á
The battery orientation is noted graphically inside the back
plate.
antenna
.
Â
Replace the battery plate to its original position.
Replace and tighten the battery plate screws.
9
10
11
With the new battery, connect the battery connector to the
device.
When properly installed, the connector plug snaps into the
port.
Reconnect the rotary switch connector to the device.
12
When properly installed, the connector plug snaps into the
port.
Verify the gasket is not damaged and is completely seated in
the groove on the front half of the device.
13
14
While ensuring the battery and rotary switch wires are not
pinched, hold the back plate and the device firmly together,
and replace all eight security screws without tightening.
Pry off the cover.
2
3
Remove the screw securing the VHF antenna to the back
plate.
Verify the back plate and the device are aligned with no
gaps.
15
Remove the six screws from the top plate, and remove the
top plate.
4
5
6
Tighten the screws evenly.
16
17
Verify the gasket is not sticking out of the device.
Remove the two screws from the battery plate, and remove
the battery plate.
Pro Trashbreaker Dog Collar Device Components
Grip the battery connector wires close to the connector, and
pull the connector perpendicular to the circuit board to
disconnect the battery connector from the device.
Remove the battery.
7
The battery fits tightly. It may be necessary to pry the battery
out of the back plate using a non-sharp, non-metal object.
Install the new battery into the front enclosure with the label
side of the battery facing up, and the lead edge of the battery
placed under the contact ledge of the device.
8
9
Replace the battery plate, and replace and tighten the two
screws.
Security screws
Top plate
À
Á
Â
Ã
Ä
Battery plate screws
Battery plate
Battery
Verify the gasket is not damaged and is completely seated in
the groove.
10
11
With the new battery, connect the battery connector to the
device.
Device Information
5
Download from Www.Somanuals.com. All Manuals Search And Download.
When properly installed, the connector plug snaps into the
port.
Replace the front plate, and replace and tighten the six
screws to secure the front plate.
12
13
Replace the screw securing the VHF antenna to the back
plate.
Replace the cover over the VHF antenna.
Replace the three screws on the cover.
14
15
16
Verify the gasket is not sticking out of the device.
Getting More Information
You can find more information about this product on the Garmin
website.
•
•
•
for information about optional accessories and replacement
parts.
Registering Your Device
Help us better support you by completing our online registration
today.
•
•
Keep the original sales receipt, or a photocopy, in a safe
place.
6
Device Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
913-397-8200
1-800-800-1020
0808 238 0000
+44 (0) 870 8501242
1-866-429-9296
+ 32 2 672 52 54
+43 (0) 820 220230
+385 1 5508 272
+385 1 5508 271
+420 221 985466
+420 221 985465
+ 45 4810 5050
+ 358 9 6937 9758
+ 39 02 36 699699
0800 0233937
+ 331 55 69 33 99
(+52) 001-855-792-7671
+47 815 69 555
00800 4412 454
+44 2380 662 915
(+35) 1214 447 460
0861 GARMIN (427 646)
+27 (0)11 251 9999
+386 4 27 92 500
+34 93 275 44 97
+ 46 7744 52020
+49 (0)180 6 427646
20 ct./Anruf. a. d.
deutschen Festnetz,
Mobilfunk max. 60 ct./Anruf
Garmin International, Inc.
1200 East 151st Street
Olathe, Kansas 66062, USA
Garmin (Europe) Ltd.
Liberty House, Hounsdown Business Park
Southampton, Hampshire, SO40 9LR UK
Garmin Corporation
No. 68, Zhangshu 2nd Road, Xizhi Dist.
New Taipei City, 221, Taiwan (R.O.C.)
© 2014 Garmin Ltd. or its subsidiaries
Download from Www.Somanuals.com. All Manuals Search And Download.
|