Safety Information . . . . . . . . 2, 3
Owner’s Manual
Operating Instructions
GCXRP090
GJSR3140
GJSR4170
GJSRP080
GJXRP080
GKSR2120
GNSR2140
GUSR2150
GWSE5190
Control Panels and Settings . . .4–8
Features . . . . . . . . . . . . . . . . 9, 10
Loading and Using
the Washer . . . . . . . . . . . . . .11–14
Stain Guide . . . . . . . . . . . . .13, 14
Troubleshooting Tips
Before You Call
For Service . . . . . . . . . . . . . 15–18
Consumer Support
Consumer Support . . . . . . . . . .20
Warranty . . . . . . . . . . . . . . . . . . 19
Write the model and serial
numbers here:
Model # ______________
Serial # ______________
You can find them in the
upper right corner on the
back of your washer.
175D1807P480 49-90211 07-04 JR
Download from Www.Somanuals.com. All Manuals Search And Download.
WHEN USING THE WASHER
ꢀ Never reach into washer while it is moving.
Wait until the machine has completely stopped
before opening the lid.
ꢀ The laundry process can reduce the flame
retardancy of fabrics. To avoid such a result,
carefully follow the garment manufacturer’s
wash and care instructions.
Use this
ꢀ Do not mix chlorine bleach with ammonia
or acids such as vinegar and/or rust remover.
Mixing different chemicals can produce a
toxic gas which may cause death.
appliance
only for its
intended
ꢀ To minimize the possibility of electric shock,
unplug this appliance from the power supply
or disconnect the washer at the building’s
distribution panel by removing the fuse or
switching off the circuit breaker before
attempting any maintenance or cleaning.
NOTE: Turning the Cycle Selector Knob to an off position,
or pressing PAUSE does NOT disconnect the appliance
from the power supply.
purpose as
described in
this Owner’s
Manual.
ꢀ Do not wash or dry articles that have been
cleaned in, washed in, soaked in or spotted with
combustible or explosive substances (such as
wax, oil, paint, gasoline, degreasers, dry-cleaning
solvents, kerosene, etc.). These substances give
off vapors that may ignite or explode. Do not add
these substances to the wash water. Do not use or
place these substances around your washer or
dryer during operation.
ꢀ Never attempt to operate this appliance if it is
damaged, malfunctioning, partially disassembled,
or has missing or broken parts, including a
damaged cord or plug.
WHEN NOT IN USE
ꢀ Turn off water faucets to relieve pressure on
hoses and valves and to minimize leakage if
a break or rupture should occur. Check the
condition of the fill hoses; they should be
replaced every 5 years.
ꢀ Do not attempt to repair or replace any part of
this appliance unless specifically recommended
in this Owner’s Manual, or in published user-
repair instructions that you understand and
have the skills to carry out.
ꢀ Before discarding a washer, or removing it
from service, remove the washer lid to prevent
children from hiding inside.
ꢀ Do not tamper with controls.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Find your washer control panel—for models GCXRP090, GJSR3140,
GJSR4170, GJSRP080, GJXRP080, GKSR2120, GNSR2140 and GUSR2150.
You can locate your model number behind the top edge of the control panel.
• Select load size and
other wash options
• Add clothes
• Add detergent
• Select wash cycle
• Close lid
• Pull knob
• Add diluted fabric
softener (on models
with a fabric
softener dispenser)
Quick Start Guide
Models GJSRP080 and GJXRP080
Model GCXRP090
Model GKSR2120
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Model GNSR2140
Model GUSR2150
Model GJSR3140
Model GJSR4170
5
Download from Www.Somanuals.com. All Manuals Search And Download.
About the control settings.
Load Size
Loosely load clothes no higher than the top row of holes in the washer basket. The water
level should just cover the clothes. Adjust the load size accordingly.
Temperature
Select the water temperature for the wash and rinse cycles. Always follow fabric
manufacturer’s care label or instructions when laundering.
Wash Cycle
The wash cycle controls the length of the washing process. The chart below will help you
match the wash cycle setting with your clothing.
COTTONS For heavy to lightly soiled cottons, household linens, work and play clothes.
CASUALS For wrinkle-free and permanent press items, and knits. Provides agitate/pause cycles to
clean your items.
EASY CARE For wrinkle-free and permanent press items, and knits.
PERMA PRESS
DELICATE For lingerie and special-care fabrics with light to normal soil. Provides periods of agitation
and soak during wash and rinse.
SUPER For heavily soiled and heavy-duty fabrics. This cycle provides a longer agitation.
PREWASH For heavily soiled clothes or for clothes with a care label that recommends prewashing
before wearing.
15 MIN/30 MIN For heavily soiled clothes. Begins with a brief agitation, soaks for a specified period of
AUTO SOAK time, then moves through the rest of the cycle automatically.
2ND RINSE Provides a second deep cold rinse.
OPTION
POWER WASH For heavily soiled and heavy-duty fabrics. This cycle provides a longer agitation.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
About the control panel—for model GWSE5190.
• Select load size and
other wash options
• Add clothes
• Add detergent
• Select wash cycle
• Close lid
• Push START button
• Add diluted fabric
softener (on models
with a fabric
Quick Start Guide
softener dispenser)
NOTE: When making a selection with any knob, simply point the knob anywhere within the shaded range for that setting.
Model GWSE5190
About the control settings.
Color Logic
Select the correct TEMPERATURE setting. Match the particular color below the words with the same color
on the Cycle Selector knob.
Example: Washing a load of medium soiled cotton towels and sheets.
Choose the LOAD SIZE.
1
Choose the TEMPERATURE setting—for this load it would be the HOT-COLD (which is a particular color).
2
Turn the Cycle Selector knob to the area that has the same color as the TEMPERATURE setting you have
chosen—for this load it would be the COTTONS area. Turn the knob to the MEDIUM setting.
3
Load Size
Loosely load clothes no higher than the top row of holes in the washer basket. The water level should just
cover the clothes. Adjust the load size accordingly.
Temperature
Select the water temperature for the wash and rinse cycles. Always follow fabric manufacturer’s care label
or instructions when laundering.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
About the control settings.
Wash Cycle
The wash cycle controls the length of the washing process. The knob can be turned in either
direction. Turning the Cycle Selector knob after starting a cycle will stop the washer and reset
the cycle to the new selection. Press START to begin the new cycle selection.
REMEMBER: When choosing
the cycle, the Cycle Selector
knob can be pointed anywhere
within the shaded range for
the cycle setting.
The Cycle Indicator Lights show what stage the washer is in. The wash time is the length of the
wash agitation. The 6 MIN light will remain lit during drain and spin. When the Selector knob is
set to a new cycle, the Indicator Lights will flash momentarily, showing what stages the cycle will
go through. On models without an AUTO SOAK option, the SOAK light will not light up.
The chart below will help you match the wash cycle setting with your clothing.
(some cycles not available on all models)
COTTONS For heavy to lightly soiled cottons, household linens, work and play clothes.
NORMAL/FAST
EASY CARE For wrinkle-free and permanent press items, and knits.
GENTLE/FAST
CASUALS For wrinkle-free and permanent press items, and knits. The HEAVY cycle has 3 agitate/pause
PULSED/SLOW cycles to clean your heavily soiled items. The MEDIUM cycle has 2 agitate/pause cycles.
Stain Assist For adding a short agitation and a soaking period to the beginning of the CASUALS cycle.
DELICATES For lingerie and special-care fabrics with light to normal soil.
GENTLE/SLOW
PREWASH For removing surface dirt from heavily soiled clothes. Make sure to follow with a regular
NORMAL/SLOW wash cycle.
Stain Wash For heavily soiled or stained items. A heavy duty wash cycle with extra agitation and
soak periods.
QUICK RINSE For quickly rinsing chlorine, perspiration, stains, etc., out of clothes.
15 MIN/30 MIN For very soiled clothes. Begins with a brief agitation, soaks for a specified period of time,
AUTO SOAK then moves through the rest of the cycle automatically.
START
Press START to begin the cycle. Pressing START again or raising the lid will PAUSE the cycle
and the Cycle indicator light will blink.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
About washer features.
Autosoak Option (on some models)
This option begins with a brief agitation, soaks for a specified period of time, then moves
through the rest of the cycle automatically. On some models, this option is located on the
Cycle Selector knob.
2nd Rinse Option (on some models)
When you use extra detergent or bleach to clean heavily soiled clothes, you may want to
use the 2nd Rinse option. It provides a second deep cold rinse.
(Appearance and features may vary)
Extended Spin Option (on some models)
Use this option to extract more water from your clothes. Clothes will be drier when this
option is selected, and will dry more quickly in your dryer.
PerfecTemp (on some models)
PerfecTemp senses the incoming water temperature and adjusts the fill water to obtain a more
precise temperature range for all three wash temperatures. You may select cold, warm or hot.
For example, in a Cold Wash selection, some warm water may be added to reach a
temperature needed to better dissolve detergents. Often, detergents are not completely
dissolved in very cold water, especially in cooler climates.
PerfecTemp
NOTE: PerfecTemp will not adjust the fill on WARM WASH unless the washer lid is closed.
Be sure to start the washer after the lid is closed.
Spot Spray (on some models)
Provides a short spray of water to allow you to dampen clothing when you pretreat stains.
Open the washer lid.
1
SPOT SPRAY
Press the SPOT SPRAY button. (You will see a short stream of water.)
2
Dampen your soiled garment with the SPOT SPRAY option and rub your favorite
pretreatment product into soiled area.
3
NOTE: The SPOT SPRAY option will not work if:
ꢀ the washer lid is down.
ꢀ the washer basket is filling.
ꢀ the water has already reached the level you selected.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
About washer features.
NOTE: Not all features are available on all washer models.
2nd Rinse Option (on some models)
When you use extra detergent or bleach to clean heavily soiled clothes, you may want to
use the 2nd Rinse option. It provides a second deep cold rinse.
Appearance and features may vary.
Liquid Bleach Dispenser (on some models)
The dispenser dilutes liquid chlorine bleach before it reaches your wash load.
Check clothing care labels for special instructions.
1
Measure liquid bleach carefully, following instructions on the bottle.
2
ꢀ Never pour undiluted liquid chlorine bleach directly onto clothes or into the wash basket.
ꢀ Do not pour powdered bleach into bleach dispenser.
Before starting the washer, pour measured amount of bleach directly into bleach
dispenser. Avoid splashing or over-filling dispenser. If you prefer to use powdered
bleach, add it into the wash basket with your detergent.
3
ꢀ Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover. Mixing can
produce a toxic gas which may cause death.
The Agitator Cap or Fabric Softener Dispenser (on some models)
The agitator cap fits into the top of the
agitator. If it accidentally comes off, simply
put it back on.
Never pour fabric softener directly on clothes.
It may stain them.
Add water to dispenser until it reaches
3
The fabric softener dispenser automatically
releases liquid fabric softener at the proper
time during the cycle.
the maximum fill line.
Do not stop the washer during the first spin.
This will cause the dispenser to empty
too soon.
To use, follow these steps:
Make sure dispenser is securely
attached to agitator.
1
Do not pour anything into the agitator if
the agitator cap or dispenser is removed.
Use only liquid fabric softener.
Pour into dispenser, using amount
recommended on package.
2
Cleaning the Fabric Softener Dispenser (on some models)
Remove the dispenser from the top of the agitator.
1
Separate the dispenser cup from the cover by grasping the top and pushing down on
the inside of the cup with your fingers. Dispenser cup will pop free from the cover.
2
To clean the dispenser, soak both the dispenser cup and the dispenser cover in the
following solution:
3
ꢀ 1 US gallon (3.8 liters) warm water
ꢀ 1/4 cup (60 ml) heavy duty liquid detergent
ꢀ 1 cup (240 ml) bleach
Separate for cleaning.
If necessary, loosen buildup with a clean, soft cloth after soaking. Do not use a stiff
brush; you may roughen the surface of the dispenser.
4
Rinse and reassemble dispenser. Place dispenser back on the agitator.
5
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading and using the washer.
Always follow fabric manufacturer’s care label when laundering.
Sorting Wash Loads
Sort by color (whites, lights, colors), soil level,
fabric type (sturdy cottons, easy care, delicates),
and whether the fabric produces lint (terry cloth,
chenille) or collects lint (velveteen, corduroy).
Proper Use of Detergent
Add detergent as the wash basket fills with water,
before you load clothes. Using too much detergent
can be a common cause of laundry problems.
Today’s detergents are formulated to be effective
without highly visible sudsing. Be sure to carefully
read and follow manufacturer’s recommendations
for how much detergent to use in your wash.
You can use less detergent if you have soft water,
a smaller load or a lightly soiled load.
Loading the Washer
Load dry items loosely, no higher than the top row
of holes in the washer basket. When loading wet
items, make sure you set the load/water level high
enough to allow the items to move freely. Water
level should just cover the clothes. To add items
after washer has started, push in Cycle Dial and
submerge additional items next to the agitator.
Close the lid and pull Cycle Dial out to restart.
ꢀ Do not wrap long items like sheets and pants around
the agitator.
ꢀ Do not wash fabrics containing flammable materials
(waxes, cleaning fluids, etc.).
ꢀ Water will fill and pump out of the washer and the
timer will advance with the lid up, but as a safety
precaution, the washer will not agitate or spin.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading and using the washer.
Always follow fabric manufacturer’s care label when laundering.
Care and Cleaning of the Washer
Wash Basket: Leave the lid open after washing to
Moving and Storage: Ask the service technician to
allow moisture to evaporate. If you want to clean the remove water from drain pump and hoses. Do not
basket, use a clean soft cloth dampened with liquid
detergent, then rinse. (Do not use harsh or gritty
cleaners.)
store the washer where it will be exposed to the
weather. For information on how to keep the tub
stationary when moving the washer, write to:
Manager, Consumer Relations, Camco Inc.,
1 Factory Lane, Suite 310, Moncton, N.B. E1C 9M3.
Fill Hoses: Hoses connecting washer to faucet
should be replaced every 5 years.
Long Vacations: Be sure water supply is shut off at
faucets. Drain all water from hoses if weather will
be below freezing.
Exterior: Immediately wipe off any spills. Wipe
with damp cloth. Try not to hit surface with
sharp objects.
Fabric Care Labels
Below are fabric care label “symbols” that affect the clothing you will be laundering.
WASH LABELS
Machine
wash
cycle
Normal
Permanent Press/
wrinkle resistant
Do not wash
Do not wring
Gentle/
delicate
Hand wash
Water
temperature
Hot
(50°C/120°F)
Warm
(40°C/105°F)
Cold/cool
(30°C/85°F)
DRY LABELS
Tumble
dry
Do not dry
(used with
do not wash)
Dry
Normal
Permanent Press/
wrinkle resistant
Gentle/
delicate
Do not tumble dry
Heat
setting
High
Medium
Low
No heat/air
Special
instructions
Dry flat
Line dry/
hang to dry
In the shade
Drip dry
BLEACH LABELS
Bleach
symbols
Any bleach
(when needed)
Do not bleach
Only non-chlorine bleach
(when needed)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing Specific Stains
Bleach Solution: To remove stains on white or bleachable
fabrics, try soaking the stained area in a container for five
minutes in the following solution and then launder in
the washer:
ꢀ 1 US gallon (3.8 liters) cool water
ꢀ 1/4 cup (60 ml) chlorine bleach
Foods on synthetic clothes may
cause stains which are virtually
invisible when you put the
clothes in the washer. If these
stains are not completely
removed in the wash, they may
pick up dirt from other clothes
in the washer and appear after
the clothes are dried.
The invisible stain
When They Become Visible:
• Rub the stain with undiluted liquid detergent.
• Let stand 30 minutes.
• Rewash using the hottest water that is safe for the fabric.
Preventing These Stains:
• Increase the amount of detergent used.
• Increase water temperature.
• Wash synthetics often.
STAIN
White and Bleachable Fabrics
Other Washable Fabrics
Adhesives
(chewing gum, etc.)
Rub with ice or immerse in
very cold water. Use dull tool
to carefully scrape off as much
adhesive or gum as possible.
Rub the stain with undiluted
liquid detergent. Rinse well,
then wash as usual.
• Same as white and bleachable fabrics.
Antiperspirants,
deodorants
Apply undiluted liquid detergent. • Same as white and bleachable fabrics except use
Rinse. If stain remains, use the
Bleach Solution; launder.
non-chlorine bleach.
Blood
Soak in cold water, then launder • Sponge or soak in cool water, then launder.
in warm water. If stain remains,
use the Bleach Solution; launder.
Chocolate, cream,
ice cream and milk
Soak in cold water. Use the
Bleach Solution; launder.
• Same as white and bleachable fabrics except use
non-chlorine bleach.
Coffee and tea
Without cream: Use the Bleach
Solution; launder.
• Sponge with warm water. If stain remains, apply warm
glycerine (available at drug stores), let stand 30 minutes
and rinse well. Wash as usual.
With cream: Soak in cold water,
then use the Bleach Solution;
launder.
Cosmetics, crayon
Use the Bleach Solution;
launder.
• Rub the stain with undiluted liquid detergent.
Rinse well, then wash as usual.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading and using the washer.
Always follow fabric manufacturer’s care label when laundering.
STAIN (cont.)
White and Bleachable Fabrics
Other Washable Fabrics
Grass, mildew, scorch
Apply undiluted liquid detergent; • Sponge with warm water. Apply undiluted liquid
launder. (Treat mildew spots
while they are fresh, before mold
has a chance to weaken fabric.)
If either type stain remains,
use the Bleach Solution; launder.
(Severe scorch stains can seldom
be removed.)
detergent; launder. Bleach with non-chlorine bleach;
launder. Old mildew cannot be removed. Scorch can
seldom be removed.
Ink, ballpoint
Fresh stains: Place stain face
down on an absorbent towel
and use a spray cleaner.
• Same as white and bleachable fabrics except launder
using non-chlorine bleach.
Rinse well, then wash as usual.
Old stains: Use the Bleach
Solution; launder.
Juices, wine,
food coloring
Soak stain in cool water.
If stain remains, use the
Bleach Solution; launder.
• Sponge with warm water. Bleach remaining stain with
non-chlorine bleach.
Perspiration
Apply undiluted liquid detergent • Launder in warm water. Rinse well. Bleach with
and launder in warm water.
If color has changed, you may
be able to restore it by treating
with ammonia or vinegar.
non-chlorine bleach.
WARNING:
Do not mix chlorine bleach with
ammonia or acids such as vinegar
and/or rust remover. Mixing can
produce a toxic gas which may
cause death.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you call for service…
Troubleshooting Tips
Save time and money! Review the charts on the following
pages first and you may not need to call for service.
WATER
Possible Causes
What To Do
Too many suds
Type of detergent
• Switch to a lower sudsing detergent brand and follow
instructions on package.
Soft water
• Try less detergent.
Too much detergent.
• Measure your detergent carefully. Use less soap if you
have soft water, a smaller load or a lightly soiled load.
Water leaks
Fill hoses or drain hose is
improperly connected
• Make sure hose connections are tight at faucets and
rubber washers are installed. Make sure end of drain
hose is correctly inserted in and secured to drain facility.
The drain hose should be inserted into the washer and
the collar or clip should be screwed in. Remove any
kinks in the drain hose and make sure that it is not
pushed too close to the wall.
Household drain may
be clogged
• Check household plumbing. You may need to call a
plumber.
Constant water pressure
to the fill hoses at the
water source
• Tighten hoses at the faucets and turn the water off after
each use.
• Check condition of the fill hoses; they should be
replaced every 5 years.
Using too much detergent
in washer
• Use less detergent. Use less soap if you have soft water,
a smaller load or a lightly soiled load.
Fill hoses, washers and screens
• The washer and screens that come with the inlet hoses
must be installed properly. Over time, these should be
replaced.
Overloading the washer
• Loosely load clothes no higher than the top row of holes
in the washer basket. The water level should just cover
the clothes.
Water temperature
seems incorrect
Cooler water temperatures
provide improved energy
efficiency
• New laundry detergents have been formulated to work
with cooler water temperatures without affecting wash
performance.
Control is not set properly
• Check water temperature control (on some models) or
Cycle knob and adjust.
Water supply is turned off
or improperly connected
• Turn both hot and cold faucets fully on and make sure
hoses are connected to correct faucets.
Water valve screens are
stopped up
•
Turn off the water source and disconnect the water fill
hoses from the upper back of the washer. Use a brush or
toothpick to clean the screens in the machine. Reconnect
the hoses and turn the water back on.
House water heater is
not set properly
• Make sure house water heater is delivering water
at 120°F–140°F (48°C–60°C).
Water won’t drain
Drain hose is kinked or
improperly connected
• Straighten drain hose and make sure washer is not
sitting on it.
• Top of drain outlet should be less than 8 ft. (2.5 m)
above floor.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you call for service…
WATER (cont.)
Possible Causes
What To Do
Water fills and drains
at the same time
Siphoning
• If your standpipe or drain for the washer is less than 3 feet
off the floor, the water will drain from the tub while it is
filling. Lifting the drain hose at least 3 feet off the floor
will allow the water to remain in the tub until the pump
drains it out. The anti-siphon clip will lift the drain hose
high enough to do this. The anti-siphon clip is included
with the installation parts package for your washer.
• Another way siphoning can occur is if the standpipe is
stuffed with rags or other items that prevent air from
escaping with the water. Air flow is needed to break
the suction.
• Check to make sure only the straight part of the drain
hose is inserted into the standpipe; no ribs of the drain
hose should be in the standpipe or drain pipe.
OPERATION
Possible Causes
What To Do
Washer pauses during
wash cycle
The washer normally pauses
between washing steps
Washer pauses during
spin cycle
This is normal
• The washer may pause during the spin cycle to remove
soapy water more efficiently.
Washer won’t operate
Washer is unplugged
• Make sure cord is plugged securely into a working outlet.
• Turn both hot and cold faucets fully on.
Water supply is turned off
Controls are not set
properly
• Check controls and make sure Cycle knob is pulled out
to ON position.
Lid is open—safety feature
prevents agitation and spinning
when lid is up
• Close lid and reset cycle, to the beginning if necessary.
Circuit breaker/fuse is
tripped/blown
• Check house circuit breakers/fuses. Replace fuses or
reset breaker. Washer should have separate outlet.
PERFORMANCE
Colored spots
Possible Causes
What To Do
Incorrect use of fabric
softener
• Check fabric softener package for instructions and
follow directions for using dispenser.
• Pretreat stain and rewash.
Dye transfer
• Sort whites or lightly colored items from dark colors.
Grayed or yellowed
clothes
Not enough detergent
• Use more detergent (especially with larger loads).
Be sure to follow detergent manufacturer’s directions.
Hard water
• Use a water conditioner like Calgon brand or install
a water softener.
Water is not hot enough
• Make sure water heater is delivering water at
120°F–140°F (48°C–60°C).
Washer is overloaded
• Select load size to match clothes load.
Detergent is not dissolving
• Add detergent as wash basket fills with water before
you load clothes.
Dye transfer
• Sort clothes by color. If fabric label states wash separately,
unstable dyes may be indicated.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
PERFORMANCE (cont.)
Possible Causes
What To Do
Lint or residue on
clothes
Clothes are air or line dried
• If you do not dry your clothes with a clothes dryer,
your clothes may retain more lint.
Incorrect sorting
• Separate lint producers from lint collectors.
Washing too long
• Wash small loads for a shorter time than larger loads.
Detergent not dissolving
• Add detergent as wash basket fills with water, before you
load clothes.
• Try a liquid detergent.
• Use warmer water temperature.
Overloading
• Load clothes no higher than the top row of holes in the
washer basket.
• Make sure load size selected matches clothes load size.
Incorrect use of fabric softener
• Check fabric softener package for instructions and
follow directions for using dispenser.
Pilling
Result of normal wear on
poly-cotton blends and
fuzzy fabrics
• While this is not caused by the washer, you can slow the
pilling process by washing garments inside out.
Snags, holes, tears, rips
or excessive wear
Pins, snaps, hooks, sharp
buttons, belt buckles,
zippers, and sharp objects
left in pockets
• Fasten snaps, hooks, buttons, and zippers.
• Remove loose items like pins, objects in pockets
and sharp buttons.
• Turn knits (which snag easily) inside out.
Undiluted chlorine bleach
• Check bleach package instructions for proper amount.
• Never add undiluted bleach to wash or allow clothes
to come in contact with undiluted bleach.
Chemicals like hair bleach
or dye, permanent wave
solution
• Rinse items that may have chemicals on them before
washing.
Wrinkling
Improper sorting
• Avoid mixing heavy items (like work clothes) with
light items (like blouses).
• Try a fabric softener.
Overloading or incorrect
water level
• Load your washer so clothes have enough room
to move freely with water covering all of the clothes.
Incorrect wash and
dry cycles
• Match Cycle selection to the type of fabric you are
washing (especially for easy care loads).
Repeated washing in
water that is too hot
• Wash in warm or cold water.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you call for service…
NOISE
Possible Causes
What To Do
Washer is noisy
Washer is uneven
• To level the front of the washer, adjust the front leveling
legs by rotating the individual leg in the proper direction
for up or down. To level back of washer, lift back of
machine 4″ (11 cm) and set down.
Washer load is unbalanced
• Push the Cycle knob in to stop the washer, open the lid
and redistribute the load evenly. Close the lid and restart.
Shipping rod is still assembled
in unit
• To remove shipping rod from washer, pull yellow tag and
attached rod from the bottom right hand side of washer.
Washer is sitting too close to wall,
causing knocking during cycle
•
•
Pull washer away from the wall; about 4″ (11 cm)
is needed.
Whistle or knock during fill
Clanking or clunking
Normal sounds during fill include the water filling
in through the house plumbing. As the water pressure
goes up and down, a knock or hammer can develop.
Make sure the water faucets are fully turned on.
•
Many washers have features such as pulse agitation and
pauses during rinse and spin for reduced clothes wear
and to reduce likelihood of soap residue. These short
pauses of less than 1 minute are normal and will reduce
clothing wear and increase water extraction. Sounds such
as a metallic knock, double knock or metallic clunk occur
when the washer transitions from a stop or paused state
to running or spinning. They occur several times per cycle
after speed changes or pauses.
OTHER
Possible Causes
What To Do
Labels on the exterior
of the washer will not
peel off cleanly
Occasionally the adhesive
used on the labels does
not release cleanly
• Use a hair dryer set at the lowest heat setting, directing
the air at the label for a short amount of time. This will
release the adhesive easily, without damaging the surface
of the washer.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Washer Warranty.
All warranty service provided by our Factory Service Centers or an authorized technician.
For service, call 1.800.361.3400.
In-home service will be provided in areas deemed reasonable by Camco.
For The Period Of: We Will Replace:
One Year
From the date of the
original purchase
Any part of the washer which fails due to a defect in materials or workmanship. During this
full one-year warranty, we will also provide, free of charge, all labor and in-home service to replace
the defective part.
Five Years
From the date of the
original purchase
The washer lid and cover, if they should rust under normal operating conditions. During this
additional four-year limited warranty, you will be responsible for any labor or in-home service costs.
Ten Years
From the date of the
original purchase
The transmission, washer basket and washer tub, if any of these parts should fail due to a defect in
materials or workmanship. During this additional nine-year limited warranty, you will be responsible
for any labor or in-home service costs.
What Is Not Covered:
ꢀ Service trips to your home to teach you how to use
ꢀ Improper installation.
the product.
If you have an installation problem, contact your
dealer or installer. You are responsible for providing
adequate electrical, exhausting and other connecting
facilities.
Read your Owner’s Manual. If you then have any questions
about operating the product, please contact your dealer
or our Consumer Affairs office at the address below.
Manager, Consumer Relations
Camco Inc.
ꢀ
Replacement of house fuses or resetting of circuit
breakers.
1 Factory Lane, Suite 310
Moncton, N.B.
E1C 9M3
ꢀ Failure of the product if it is misused, or used for
other than the intended purpose or used
commercially.
ꢀ
Damage to product caused by accident, fire, floods
or acts of God.
ꢀ
Damage to finish not reported within 48 hours
following the delivery of the appliance.
WARRANTOR IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES.
Warrantor: CAMCO INC.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Support.
GE Appliances Website
Have a question or need assistance with your appliance? Visit our Website, www.geappliances.ca, 24 hours a day,
any day of the year!
Schedule Service
1.800.361.3400
GE repair service is close to you.
To arrange service for your GE appliance, all you have to do is call.
In-home service will be provided in areas deemed reasonable by Camco.
Real Life Design Studio
Upon request, GE can provide a brochure on designing a kitchen for persons with limited mobility.
Contact: Manager, Consumer Relations, Camco, Inc.
Suite 310, 1 Factory Lane
Moncton, N.B. E1C 9M3
Extended Warranties
Purchase a GE service contract before your warranty expires and benefit from a substantial rebate. That way
GE service will always be there after your warranty expires.
Visit our Website or call 1.800.461.3636.
Parts and Accessories
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes
(VISA, MasterCard and Discover cards are accepted).
Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally should be
referred to qualified service personnel. Caution must be exercised, since improper servicing may cause unsafe operation.
You will find the nearest Camco Service Center number in the yellow pages of your phone book. Or, call us at
1.888.261.3055.
Contact Us
If you are not satisfied with the service you have received:
First of all, communicate with the people who repaired your appliance.
Then, if you are still not satisfied, send all information including telephone number to:
Director, Consumer Relations, Camco, Inc.
Suite 310, 1 Factory Lane
Moncton, N.B. E1C 9M3
Register Your Appliance
Register your new appliance on-line—at your convenience! Timely product registration will allow for
enhanced communication and prompt service under the terms of your warranty, should the need arise.
You may also mail in the pre-printed registration card included in the packing material.
Printed in the United States
20
Download from Www.Somanuals.com. All Manuals Search And Download.
|