Household Beverage Cooler
Record Serial/Model Numbers ………………....2
Important Safety Instructions ……….………….2
First Steps …………………………….……………3
General Operation ………………………………..6
Helpful Hints ………………………….……………7
Energy Saving Tips ..……………..………………8
Beverage Cooler Features ………………………8
Cleaning and Maintenance ……………….……..8
Warranty …………………………………….….…10
Troubleshooting Guide ………………………...11
P/N 297017400 (Oct 2004)
Download from Www.Somanuals.com. All Manuals Search And Download.
• If voltage varies by 10% or more, performance of your
beverage cooler may be affected. Operating beverage
cooler with insufficient power can damage the
compressor.
• To prevent the beverage cooler from being turned off
accidentally, do not plug unit into an outlet controlled by
a wall switch or pull cord. It is recommended that a
separate circuit serving only your beverage cooler be
provided.
This Use and Care Manual provides specific assembly,
operating and maintenance instructions for your model. Use
the beverage cooler only as instructed in this Use and Care
Manual. Before starting the beverage cooler, follow these
important first steps.
PARTS AND ACCESSORIES
• Do not pinch, knot, or bend the cord in any manner.
Your beverage cooler comes with a box that contains all the
parts and accessories needed for your beverage cooler.
Check to make sure that you have received the box
containing all of the components listed below. You will need
the following tools to assemble the beverage cooler.
• DO NOT use this appliance outside. It is designed for
indoor use only.
• NEVER unplug the beverage cooler by pulling on the
cord. Always grip the plug firmly, and pull straight out
from the receptacle.
• To avoid electrical shock, unplug the beverage cooler
before cleaning.
NOTE: Turning the temperature control to “OFF” turns off
the compressor, but does not disconnect the power to other
electrical components.
PHILLIPS™
SCREWDRIVER
SOCKET
WRENCH
ADJUSTABLE
WRENCH
PLIERS
DRIP TRAY AND MOUNTING HARDWARE BOX
(1) Drip Tray
1 piece
1 piece
1 piece
1 piece
6 pieces
1 piece
1 piece
2 pieces
(2) Drip Tray Cover
(3) Drip Tray Bracket
(4) CO2 Canister Bracket
(5) Mounting Screws
(6) 4” Long Carriage Bolt
(7) Wing Nut
(8) Hose Routing Clips
CO2 CANISTER SAFE HANDLING
• CO2 canisters must be handled with extreme care. They
contain potentially hazardous high pressure compressed
gas.
• ALWAYS connect CO2 gas canisters to a pressure
regulator.
• NEVER drop or throw the CO2 canister.
• NEVER connect gas canister directly to keg.
• ALWAYS keep CO2 canisters in a cool place (70º or
less) and away from heat.
(3) DRIP TRAY
BRACKET
(4) CO2 CANISTER
BRACKET
(1) DRIP TRAY
(2) DRIP TRAY
COVER
• In case of CO2 leakage, ventilate and evacuate the area
immediately.
• ALWAYS keep canister secured in an upright position.
• Check the Department of Transportation (D.O.T.) test
date on the canister neck and do not use if older than 5
years.
(5) MOUNTING
SCREW
(6) 4” LONG
CARRIAGE BOLT
(7) WING NUT
(8) HOSE
ROUTING CLIP
• Return outdated canister to your gas supplier for one that
is within the time window.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEVERAGE DELIVERY KIT BOX
(9) Faucet and Shank Assembly
(10) Plastic Collar
(11) Shank Nut
(12) Faucet Knob
(13) Regulator
1 piece
1 piece
1 piece
1 piece
1 piece
1 piece
1 piece
1 piece
2 pieces
2 pieces
1 piece
(14) Keg Coupler
(15) Clear Hose (Delivery Line)
(16) Red Hose (Gas Line)
(17) Rubber Washer (Black)
(18) Plastic Hose Clamp (White)
(19) CO2 Canister (Empty)
(9) FAUCET &
SHANK ASS’Y.
(10) PLASTIC
COLLAR
(11) SHANK NUT
(12) FAUCET
KNOB
INSTALLATION – GENERAL INSTRUCTIONS
• Choose a place that is near a grounded electrical outlet.
DO NOT use an extension cord or an adapter plug.
• For the most efficient operation, the beverage cooler
should be located where surrounding temperatures will not
drop below 10ºF (-12ºC) or exceed 110ºF (43ºC).
• Allow space around the unit for good air circulation. Leave
a 3 inch (75 mm) space on all sides of the beverage cooler
for adequate air circulation.
(13) REGULATOR
(14) KEG
COUPLER
(15) CLEAR HOSE
(DELIVERY LINE)
(16) RED HOSE
(GAS LINE)
(19) CO2
CANISTER
(17) RUBBER
WASHER
(18) HOSE
CLAMP
LEVELING
The beverage cooler must have all bottom corners resting
firmly on a solid floor. The floor must be strong enough to
support a fully loaded beverage cooler. NOTE: It is Very
Important for your beverage cooler to be level in order to
function properly. If the beverage cooler is not leveled during
installation, the door may be misaligned and not close or seal
properly, causing cooling, frost, or moisture problems.
NOTE: The exterior walls of the beverage cooler may
become quite warm as the compressor works to transfer heat
from the inside. Temperatures as much as 30ºF warmer than
the room temperature can be expected. For this reason it is
particularly important in hotter climates to allow enough
space for air circulation around your beverage cooler.
To Level Your Beverage Cooler:
Carefully tip the unit onto its back. Remove and discard the
wood skid from the bottom using a 3/8” socket wrench. After
discarding crating screws and wood skid, use a carpenter’s
level to level the beverage cooler from front to back. Adjust
the plastic leveling feet in front, ½ bubble higher, so that the
door closes easily when left halfway open.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CO2 CANISTER BRACKET INSTALLATION
REGULATOR INSTALLATION
• Align the two bracket holes with the screw anchor holes
located on the lower left side of the cabinet (the actual
screw anchor holes are centered behind the taped hole).
• Secure the CO2 canister bracket (4) to the cabinet with
the two supplied mounting screws (5) using a PhillipsTM
screwdriver.
• Fasten the CO2 regulator (13) to the CO2 canister (19),
tightening the nut securely. DO NOT over tighten. Over
tightening may damage the gasket in nut of the regulator.
NUT
(4) CO2
CANISTER
BRACKET
(5)
(23)
REGULATOR
MOUNTING
SCREWS
(29) CO2
CANISTER
DRIP TRAY ASSEMBLY INSTALLATION
RED HOSE TO REGULATOR CONNECTION
• Make sure the notched back corners are on top and attach
the Drip Tray Bracket (3) to the door using four supplied
mounting screws (5).
• Drop the Drip Tray (1) onto the bracket.
• Drop the Drip Tray Cover (2) onto the drip tray.
• Attach one end of the red hose (16) to the hose barb of the
CO2 regulator (13). Secure the hose using one of the two
hose clamps (18) provided. Use pliers to snap the hose
clamp tight to assure that there is no gas leak.
(2) DRIP TRAY
COVER
(3) DRIP TRAY
(1) DRIP
TRAY
(13) REGULATOR
(18) HOSE CLAMP
BRACKET
(5) MOUNTING
SCREW
(16) RED HOSE
FAUCET ASSEMBLY INSTALLATION
• Attach Faucet Knob (12) to Faucet & Shank Assembly (9).
• Slip the Faucet & Shank Assembly through the black plastic
Collar (10) and hole in the door.
• Thread on the large Shank Nut (11) and, using an
adjustable wrench, tighten until snug. DO NOT OVER
TIGHTEN.
RED HOSE TO COUPLER CONNECTION
• Fasten the other end of the red hose (16) to the keg
coupler (14) using the remaining hose clamp (18). Use
pliers to snap the clamp tight to assure that there is no gas
leak.
(12) FAUCET KNOB
(14) KEG COUPLER
(18) HOSE CLAMP
(9) FAUCET &
SHANK ASSEMBLY
(16) RED HOSE
(11) SHANK
NUT
(10) PLASTIC
COLLAR
CLEAR HOSE TO COUPLER CONNECTION
CLIP ATTACHMENT TO DOOR PANEL
• Attach the end of the clear hose (15) (beverage delivery
line) with the large wing nut to keg coupler (14). Be sure to
place the supplied rubber washer (17) inside the nut to
prevent leakage.
• Attach the two supplied hose routing clips (8) to the door
panel approximately 1~2 in (25~50mm) from the left door
edge. See delivery hose arrangement on page 6.
(14) KEG
COUPLER
(8) HOSE
ROUTING CLIP
(15) CLEAR
HOSE
DOOR PANEL
5
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEAR HOSE TO DOOR PANEL CONNECTION
DELIVERY HOSE ARRANGEMENT
• Place the supplied rubber washer (17) inside the hex nut
on the other end of the clear hose (15) (beverage delivery
line) and attach to shank protruding from the door panel
• Insert the clear hose (15) (delivery hose) into the hose
routing clips (8) attached to the door panel. Once the
hoses are properly secured, the CO2 canister valve can
now be opened.
(15) CLEAR HOSE
(8) HOSE
(15) CLEAR HOSE
ROUTING CLIPS
DOOR PANEL
DOOR PANEL
COUPLER TO KEG INSTALLATION
• Align lug locks on tap head with lug housing on top of keg
and insert the tap head.
• Turn the tap head handle ¼ turn clockwise. The tap head
is now secured to the keg.
• Pull the tap handle out and push down to open the port in
the keg.
CONNECTIONS
CO2 CANISTER TO CABINET INSTALLATION
GENERAL OPERATION
• Place the CO2 canister (19) with the regulator (13) inside
the CO2 Canister Bracket (4) in the cabinet. It is important
that the canister be kept in an upright position to operate
efficiently. Fasten the canister securely in place using the
4” long carriage bolt (6) and wing nut (7) supplied with this
unit.
SETTING THE TEMPERATURE CONTROL
The temperature control is located on the back side of the
beverage cooler. The temperature is factory preset for
satisfactory
storage
temperature.
However,
the
(19) CO2
temperature control is adjustable to provide a range of
temperatures for your personal satisfaction. If a colder
temperature is desired, turn the control shaft of the cold
control clockwise using the tip of the screwdriver as shown
in the diagram below. To set the cold control to “OFF”
position, turn the control shaft counter-clockwise until it
stops. Allow several hours for the temperature to stabilize
between adjustments.
CANISTER
(6) 4” LONG
CARRIAGE BOLT
(13)
REGULATOR
(4) CO2
CANISTER
BRACKET
(7) WING NUT
KEG TO CABINET INSTALLATION
• Place the keg next to the CO2 canister (19) inside the
cabinet as shown.
(19) CO2
CANISTER
KEG
6
Download from Www.Somanuals.com. All Manuals Search And Download.
• With the canister valve still in closed position, reattach the
regulator to the new canister using an adjustable wrench.
Tighten nut until it feels snug but be careful not to over
tighten as you will damage the gasket inside the stem nut.
• Check to make sure that the red gas line hose is still
securely attached to the regulator.
• Open the canister valve all the way by turning counter
clockwise until it stops. This valve seals at both the fully
open and fully closed positions. Failure to completely open
or close the valve could result in premature loss of CO2
pressure.
• Open the regulator shut-off valve by moving it down to the
6 o’clock position.
• Check gauge pressure. Adjust the regulator shut-off valve
as necessary until the pressure reads between 12 to 14
psi.
OPERATING YOUR BEVERAGE COOLER
• Make sure that the beverage cooler is plugged in
properly to a 115V, 60Hz AC only electrical outlet. Refer
to Electrical Information on page 2.
• Make sure that the drip tray is secured under the faucet.
• Start with a clean beverage glass that has been wetted in
cold water. Place the glass at a 45º angle, one inch
below the faucet. Do not let the glass touch the faucet.
Open the faucet all the way.
• After the glass has reached half full, gradually bring the
glass to an upright position.
• Let the remaining beverage run straight down the middle.
This insures proper release of CO2 by producing a ¾” to
a 1” foam head.
• Close the faucet completely and quickly.
CANISTER VALVE
NOTE: It is normal to see condensation forming around the
faucet. This condensation is caused by the temperature
difference between the cold beverage and the inner
surfaces of the faucet when beverage is being drawn
through the line.
NUT
REGULATOR
HELPFUL HINTS
CO2 CANISTER
SHUT-OFF VALVE
PARTS OF A CO2 REGULATOR
(A) Low Pressure Gauge
(B) Regulator Adjustment Screw
(C) Adjustment Lock Nut
(D) Shut-off Valve
TIPS ON INSTALLING THE KEG TO THE CABINET
SAFE KEG HANDLING
(E) CO2 Nut (used to connect to CO2 Canister)
(F) High Pressure Gauge
• Installing the keg to the cabinet is a two-person team
effort. NEVER lift a full ½ keg alone. Doing so may cause
severe injury.
• With the door fully open and the help of another person,
lift the keg vertically on both sides until the keg is above
the bottom of the cabinet interior.
A
E
• Set the edge of the keg on top of the stainless protective
plate located on the bottom of the cabinet interior. Slide
the keg back until it is fully inside the cabinet.
C
F
B
D
• Care must be taken to avoid damage to the evaporator
coils located on the back side of the cabinet interior.
HOW TO REPLACE AN EMPTY CO2 CANISTER
• Close the canister valve of the empty canister by turning
clockwise until it stops.
• Close the regulator shut-off valve by moving it in the 3
o’clock position.
• Carefully remove regulator from the empty CO2 canister by
loosening the nut with an adjustable wrench. Check the
condition of the gasket inside the nut and replace if
necessary.
• Return canister to your local carbonic gas source for filling
(we suggest looking in your yellow pages under “Carbonic
Gas”. Sources of CO2 vary from community to community
but it is often available at welding supply stores and
beverage distributors).
• Remove dust cap from new canister nut, if any.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
BEER STORAGE TEMPERATURE
OPTIONAL CASTER KIT
If you’d like to make your beverage cooler so it can be rolled
from room to room, there is an optional caster kit available
from your authorized Frigidaire dealer or service center. Just
ask for part number 297027300 - Caster, Rail and Hardware
Kit, which includes 2 fixed casters, 2 swivel casters, 2 caster
support rails and mounting hardware.
• Draft beer is not pasteurized, so it must be kept cold,
preferably at 38ºF. Temperatures above 38ºF may cause
the beer to become wild, turn sour and cloudy.
TYPICAL BEER SERVING EQUIVALENTS
½ Keg = 15 ½ Gallons = 1984 Fluid Ounces
½ Keg = 6 ¾ Cases of 12 ounce bottles
Overall weight of full ½ Keg is approximately 165 pounds.
¼ Keg = 7 ¾ Gallons = 992 Fluid Ounces
¼ Keg = 3 3/8 Cases of 12 ounce bottles
Overall weight of full ¼ Keg is approximately 82.5 pounds.
CASTERS
ENERGY SAVING TIPS
• Install the beverage cooler in the
coolest part of the room, out of
direct sunlight and away from
heating ducts or registers. Do not
place the beverage cooler next to
heat-producing appliances such
as a range oven or dishwasher.
• Do not overcrowd the beverage cooler or block cold air
vents. Doing so causes the beverage cooler to run longer
and use more energy. Shelves should not be lined with
aluminum foil, wax paper or paper toweling. Liners
interfere with air circulation, making the beverage cooler
less efficient.
CLEANING AND MAINTENANCE
CLEANING THE INSIDE
• Organize the beverage cooler to reduce door openings.
Remove as many items as needed at one time and close
the door as soon as possible.
• Wash inside surfaces of the beverage cooler with a
solution of two tablespoons of baking soda in one quart
(1.136 liters) warm water. Rinse and dry. Wring excess
water out of the sponge or cloth when cleaning in the area
of the controls, or any electrical parts.
BEVERAGE COOLER FEATURES
• Wash the removable parts with the baking soda solution
mentioned above, or mild detergent and warm water.
Rinse and dry. NEVER use metallic scouring pads,
brushes, abrasive cleaners, or alkaline solutions on any
surface. DO NOT wash removable parts in the dishwasher.
ADJUSTABLE INTERIOR SHELVES
Multi-position adjustable interior shelves can be moved to
any position for larger or smaller packages. The shipping
spacers that stabilize the shelves for shipping should be
removed and discarded.
CLEANING THE OUTSIDE
Wash the cabinet with warm water and mild liquid
detergent. Rinse well and wipe dry with a clean soft cloth.
Replace parts.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
• Remove the coupler from keg by rotating it
counterclockwise.
DOOR REMOVAL
• Remove the red hose (gas line) from the coupler. Make
sure the canister valve and regulator shut-off valve is shut
off before removing the hose.
If door must be removed:
• Gently lay the beverage cooler on its back, on a rug or
blanket.
• Remove the faucet from the shank assembly by turning the
threaded stainless steel collar clockwise using a faucet
wrench.
• Disassemble the faucet parts and place in the cleaning
solution bucket.
• Attach the brass attachment on the end of the cleaning
hose to the faucet shank assembly by turning the stainless
steel collar counterclockwise. Tighten the collar slightly.
• If the coupler has a shutoff, make sure it is in the open
position.
• Remove plastic top hinge cover.
• Remove screws from top hinge.
• Remove top hinge from cabinet.
• Remove bottom hinge screws.
• Remove door and bottom hinge from cabinet.
• To replace door, reverse the above order and securely
tighten all screws to prevent hinge slippage.
• Place the keg coupler in the cleaning solution bucket and
pump the cleaning solution through the beer line.
• Clean the faucet parts and keg coupler thoroughly using
the faucet cleaning brush. Also, use the faucet cleaning
brush to clean around the shank and coupling.
• Rinse all the parts with cool fresh water and reassemble
the faucet.
• Detach the cleaning solution bottle from the faucet shank
by turning the threaded stainless steel collar clockwise.
Rinse the bottle with cool fresh water.
• Fill the bottle with fresh water and re-attach it to the faucet
shank assembly. Pump the water through the beverage
line (clear hose). Make sure the end of the line is in a
bucket to collect rinse water.
• Disconnect the cleaner and reinstall the faucet to the
shank by turning the collar counterclockwise using a faucet
wrench and tightening it slightly. DO NOT over tighten the
collar.
If
leaving
the
beverage cooler door open at any
time, make certain that children
cannot get into the beverage cooler
and become entrapped.
• Reattach the red hose (air line) to the keg coupler and
open both the canister valve and regulator shut-off valve.
• Reattach the keg coupler to the keg. Refer to Coupler –
Keg Installation procedures.
• Remove the drip tray and cover from the door and clean
thoroughly. Refer to Cleaning and Maintenance Guide.
• Reinstall the drip tray and cover to the door. Refer to Drip
Tray Assembly Installation procedures.
PROPER CLEANING OF BEVERAGE COOLER
Your beverage cooler’s beverage dispensing system needs
regular cleaning and sterilization in order to continue serving
draft beer with its pure brewery flavor. It is recommended that
the delivery lines be cleaned weekly and the entire delivery
system cleaned before a new keg is attached. This is a
relatively simple task. You will need the following parts to
clean your unit’s dispensing system. These parts are
available at any draft beer dispensing equipment supplier.
One such supplier is Micro Matic. They can be reached at
NOTE: Read and follow the instructions that come with the
cleaning kit before cleaning your beverage cooler.
VACATION AND MOVING TIPS
(A) 1 quart Plastic Cleaning Bottle
(B) Low Profile Hand Pump
(C) Solid Brass Faucet Cleaning Attachment
(D) 4 oz. Bottle of Cleaning Solution
(E) Faucet Wrench
• If the unit will not be used for several months, unplug the
power cord, clean and dry the interior thoroughly and
leave the door open slightly, blocking it open if
necessary, to prevent odor and mold growth.
(F) Faucet Cleaning Brush
• Mix one gallon of warm water with one ounce of the
cleaning solution in a bucket.
• When moving the unit, disconnect the power cord from
the wall outlet. Thoroughly clean the interior and secure
all loose items by taping them securely in place to
prevent damage. In the moving vehicle, secure the unit in
an upright position to prevent movement. Also, protect
the outside of the unit with a blanket, or similar item.
• Remove the bottle cap and fill the bottle with the solution.
Replace the cap. Do not discard the remaining solution.
• Before removing the beverage hose from the tap or from
the coupler, make sure the remaining beverage in the
delivery line is blown out. This can be done by quickly
opening and closing the regulator outlet valve.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
BEVERAGE COOLER WARRANTY
Your beverage cooler is protected by this warranty
WARRANTY
PERIOD
THROUGH OUR AUTHORIZED SERVICERS,
WE WILL:
THIS CONSUMER WILL BE RESPONSIBLE FOR:
FULL ONE-YEAR
WARRANTY
One year from
original purchase
date
Pay all costs for repairing or replacing any parts of
this appliance which prove to be defective in
materials or workmanship.
Costs of service calls that are listed under NORMAL
RESPONSIBILITIES OF THE CONSUMER.*
LIMITED 2ND~5TH
YEAR WARRANTY
(Cabinet Liner and
Sealed System)
Second through
fifth years from
original purchase
date
Repair or replace any parts in the cabinet liner or
Costs for pick up and delivery of the appliance required
because of service. Costs for labor, parts and transportation
other than with respect to the cabinet liner or Sealed
Refrigeration System.
Sealed
Refrigeration
System
(compressor,
condenser, evaporator, drier and tubing) which
prove to be defective in materials or workmanship.
LIMITED
WARRANTY
(Applicable to the
State of Alaska)
Five years from
original purchase
date
All of the provisions of the warranties above and the
exclusions listed below apply.
Costs of the technician’s travel to the home and any costs for
pick up and delivery of the appliance required because of
service.
In the U.S.A., your appliance is warranted by Electrolux Home Products, Inc. We authorize no person to change or add to any of our
obligations under this warranty. Our obligations for service and parts under this warranty must be performed by us or any authorized Electrolux
Home Products, Inc. servicer. In Canada, your appliance is warranted by Electrolux Canada Corp.
*NORMAL
RESPONSIBILITIES
OF THE CONSUMER
This warranty applies only to products in ordinary household use, and the consumer is responsible for the items
listed below:
1. Proper use of the appliance in accordance with instructions provided with the product.
2. Proper installation by an authorized servicer or in accordance with instructions provided with the appliance and in
accordance with local plumbing, electrical and/or gas codes.
3. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose
connections or defects in house wiring.
4. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc., which
are not a part of the appliance when it was shipped from the factory.
5. Damages to finish after installation.
6. Replacement of light bulbs and/or fluorescent tubes (on models with these features).
This warranty does not cover the following:
EXCLUSIONS
1. CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES
RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY.
NOTE: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation
or exclusion may not apply to you.
2. Service calls which do not involve malfunction or defects in workmanship or material, or for appliances not in ordinary
household use. The consumer shall pay for such service calls.
3. Damages caused by services performed by servicers other than Electrolux Home Products, Inc. or its authorized
servicers; use of parts other than genuine Electrolux Home Products, Inc. parts; obtained from persons other than
such servicers; or external causes such as abuse, misuse, inadequate power supply or acts of God.
4. Products with original serial numbers that have been removed or altered and cannot be readily determined.
Keep your bill of sale, delivery slip, or some other appropriate payment record. The date on the bill establishes the
warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all
receipts. This written warranty gives you specific legal rights. You may also have other rights that vary from state to state.
Service under this warranty must be obtained by contacting Electrolux Home Products, Inc. or Electrolux Canada Corp.
IF YOU NEED
SERVICE
This warranty only applies in the 50 states of the U.S.A., Puerto Rico, and Canada. Product features or specifications as described or
illustrated are subject to change without notice. All warranties are made by Electrolux Home Products, Inc. In Canada, your appliance is
warranted by Electrolux Canada Corp.
01-U-FR-02 (Rev. 02/2004)
USA
800-944-9044
Canada
800-265-8352
Electrolux Home Products, Inc.
P.O. Box 212378
Augusta, GA 30917
Electrolux Canada Corp.
6150 McLaughlin Road
Mississauga, Ontario
L5R 4C2
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Before calling for service, review this list. It may save you time and expense. This list
includes common occurrences that are not the result of defective workmanship or
materials in this appliance.
TROUBLESHOOTING
GUIDE
PROBLEM
CAUSE
CORRECTION
BEVERAGE COOLER OPERATION
Beverage cooler does not run.
•Beverage cooler is plugged into a circuit that has a
ground fault interrupt.
•Temperature control is in the “OFF” position.
•Use another circuit. If you are unsure about the
outlet, have it checked by a certified technician.
•See SETTING THE TEMPERATURE CONTROL
Section.
•Beverage cooler may not be plugged in, or plug may
be loose.
•Ensure plug is tightly pushed into outlet.
•House fuse blown or tripped circuit breaker.
•Check/replace fuse with a 15 amp time-delay fuse.
Reset circuit breaker.
•Power outage.
•Check house lights. Call local Electric Company.
Beverage cooler runs too
much or too long.
•Room or outside weather is hot.
•It’s normal for the beverage cooler to work harder
under these conditions.
•Beverage cooler has recently been disconnected for
a period of time.
•It takes 4 hours for the beverage cooler to cool
down completely.
•Doors are opened too frequently or too long.
•Beverage cooler door may be slightly open.
•Temperature control is set too low.
•Warm air entering the beverage cooler causes it to
run more. Open door less often.
•See “DOOR PROBLEMS” Section.
•Turn the control shaft to a warmer setting. Allow
several hours for temperature to stabilize.
•Beverage cooler gasket is dirty, worn, cracked, or
poorly fitted.
•Clean or change gasket. Leaks in the door seal will
cause beverage cooler to run longer in order to
maintain desired temperature.
Interior beverage cooler
temperature is too cold.
•Temperature control is set too low.
•Temperature control is set too warm.
•Turn the control shaft to a warmer setting. Allow
several hours for temperature to stabilize.
Interior beverage cooler
temperature is too warm.
•Turn the control shaft to a colder setting. Allow
several hours for temperature to stabilize.
•Door is kept open too long or is opened too
frequently.
•Warm air enters the beverage cooler every time the
door is opened. Open the door less often.
•Door may not be seating properly.
•See “DOOR PROBLEMS” Section.
•Beverage cooler has recently been disconnected for
a period of time.
•Beverage cooler requires 4 hours to cool down
completely.
Beverage cooler external
surface temperature is warm.
•The external walls can be as much as 30ºF warmer
than room temperature.
•This is normal while the compressor works to
transfer heat from inside the beverage cooler
SOUND AND NOISE
Louder sound levels whenever
beverage cooler is on.
•Modern beverage coolers have increased storage
capacity and more stable temperatures. They
require a high efficiency compressor.
•This is normal. When the surrounding noise level is
low, you might hear the compressor running while it
cools the interior.
Longer sound levels when
compressor comes on.
•Beverage cooler operates at higher pressures
during the start of the “ON” cycle.
•This is normal. Sound will level off or disappear as
the beverage cooler continues to run.
Fan runs when room
temperature is below 45ºF.
•Exterior thermostat has activated the heater and
fan.
•This is normal.
Popping or cracking sound
when compressor comes on.
•Metal parts undergo expansion and contraction, as
in hot water pipes.
•This is normal. Sound will level off or disappear as
refrigerator continues to run.
Bubbling or gurgling sound,
like water boiling.
•Refrigerant (used to cool beverage cooler) is
circulating throughout the system.
•This is normal.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SOUND AND NOISE (Cont.)
Vibrating or rattling noise.
•Beverage cooler is touching the wall.
•Move beverage cooler slightly away from the wall.
•This is normal.
Snapping sound.
•Cold control turning beverage cooler on and off.
WATER / MOISTURE / FROST INSIDE BEVERAGE COOLER
Moisture forms on inside of
beverage cooler walls.
•Weather is hot and humid.
•This is normal.
•Door may not be seating properly.
•Door is kept open too long or opened too frequently.
•See “DOOR PROBLEMS” Section.
•Open the door less often.
WATER / MOISTURE / FROST OUTSIDE BEVERAGE COOLER
Moisture forms on outside of
beverage cooler walls.
•Door may not be seating properly, causing the cold
air from inside the beverage cooler to meet warm
moist air from outside.
•See “DOOR PROBLEMS” Section.
ODOR IN BEVERAGE COOLER
Odors in beverage cooler.
•Interior needs to be cleaned.
•Clean interior with sponge, warm water, and baking
soda.
DOOR PROBLEMS
Door will not close.
•Beverage cooler is not level. It rocks on the floor
when it is moved slightly.
•This condition can force the cabinet out of square
and misalign the door. Level the unit.
COMMON DRAFT PROBLEMS
WILD BEER
–
Beer, when
•Beer drawn improperly.
•Make sure faucet is opened all the way. Close
quickly when done.
•Replace regulator.
drawn, is all foam, or too
much foam and not enough
liquid beer.
•Creeping regulator.
•Applied pressure is set too high.
•Readjust regulator to a lower pressure until foam
subsides. When pressure is properly set, you should
be able to pour 10 oz. of beer in about 5 seconds.
•Make sure beer delivery line is not pinched and is
fully inside the interior of the beverage cooler.
•Wait until keg cools down to proper temperature.
•Have beverage cooler serviced to return it to proper
operating condition.
•Hot spots in line.
•Tapped into a warm keg (should be 34ºF ~ 38ºF).
•Cooler malfunctioning.
•Faucets in bad, dirty or worn condition.
•Thoroughly clean faucet with recommended
cleaning kit. Replace any worn seals.
FLAT BEER – Foamy head
disappears quickly; beer lacks
usual zestful brewery fresh
flavor.
•Dirty glasses.
•Applied pressure is set too low.
•Wash glasses using soap-free detergent.
•Increase pressure until beer flows at a rate of 2 oz.
per second.
•Do not turn off CO2 supply line to keg until keg is
empty and ready to be removed.
•Increase temperature of beverage cooler (see
SETTING THE TEMPERATURE CONTROL).
•Check that coupler is properly installed in keg.
•Replace regulator.
•CO2 is turned off.
•Beer too cold.
•Loose tap or vent connections.
•Sluggish regulator.
CLOUDY BEER – When beer
in glass appears hazy, not
clear.
•Frozen or nearly frozen beer.
•Return keg to place of purchase and exchange for
one that has been properly refrigerated.
•Exchange keg for fresh one.
•Wash glasses using soap-free detergent.
•Clean faucet with recommended cleaning kit.
•Unrefrigerated beer for long periods of time.
•Dirty glasses.
•Dirty faucet.
•Unrefrigerated foods placed on top of cold keg.
•Remove items from atop keg and place in
separate refrigerator.
a
12
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Ways To Contact Us!
¡3 formas de contactarnos!
3 façons de nous contacter !
USA, EE.UU., É.-U.
1-800-944-9044
CANADA, CANADÁ
1-866-213-9397 (English)
1-866-294-9911 (Français)
Or, O, Ou
USA, EE.UU., É.-U.
CANADA, CANADÁ
Electrolux Home Products, Inc.
P.O. Box 212378
Augusta, GA 30917
Electrolux Canada Corp.
6150 McLaughlin Road
Mississauga, Ontario
L5R 4C2
Or,O, Ou
Visit Frigidaire’s Web Site At:
Visite la página de Frigidaire en Internet:
Visitez le site Internet de Frigidaire au :
© 2004 Electrolux Home Products, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|