Fisher Price Saw 79638 User Manual

Healthy Care  
High Chair  
Product features and decoration may vary from the photo above.  
Model Number: 79638, 79639, 79640, 79641, B2875  
Please keep this instruction sheet for future reference, as it contains important information.  
Adult assembly is required.  
Tool needed for assembly: Phillips Screwdriver (not included).  
Disc  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts  
Pad  
Food Tray  
Base Tray  
Seat Back  
Seat  
Bottom  
Frame  
#10 x 7/8"  
Black Screw  
Hinge  
Rod  
Storage  
Caddy  
#8 x 3/4" Screws  
2 Seat Bottom Tubes  
4 Screw Retainers  
#8 x 3/4"  
Screws  
#10 x 7/8"  
Black Screw - 4  
#8 x 3/4" Screws  
Frame  
Footrest  
Back Base  
Front Base  
#10 x 7/8"  
Black Screws  
#8 x 3/4" Screw - 8  
SHOWN ACTUAL SIZE  
#10 x 7/8" Black Screw - 7  
SHOWN ACTUAL SIZE  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
IMPORTANT! Before assembly, inspect this product for  
damaged hardware, loose joints, missing parts or sharp  
edges. DO NOT use if any parts are missing or broken.  
Contact Fisher-Price® for replacement parts and instructions  
if needed. Never substitute parts.  
Seat  
Bottom  
Tubes  
Footrest  
Plastic  
Rings  
Seat Bottom  
Plastic  
Rings  
3
• Align the holes in the plastic  
rings and the seat bottom tubes.  
• Insert a #8 x 3/4" screw through  
each plastic ring and into the  
seat bottom tubes, as shown.  
1
#8 x 3/4" Screw - 4  
SHOWN ACTUAL SIZE  
• Place the seat bottom face down on a flat surface.  
• At an angle, fit the footrest on the seat bottom, as shown.  
• Tighten the screws with a Phillips screwdriver.  
Do not over-tighten.  
• Push the seat bottom tubes back and forth to be sure they  
are secured to the seat bottom. If the seat bottom tubes  
move, you have probably not fastened them properly.  
Remove the screws and check to be sure the screw holes in  
the seat bottom tubes and seat bottom plastic rings are  
aligned. Replace and tighten the screws.  
Plastic  
Rings  
Seat Bottom Tubes  
Footrest  
Insert Screws  
Here  
Plastic  
Rings  
2
• Slide a seat bottom tube through each set of plastic rings  
on the seat bottom.  
4
#10 x 7/8" Black Screw - 2  
SHOWN ACTUAL SIZE  
• Insert two #10 x 7/8" black  
screws through the footrest  
and into the seat bottom.  
• Tighten the screws with a Phillips screwdriver.  
Do not over-tighten.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Frame Leg  
Seat Back  
Pin  
Seat Back  
Pin  
Opening  
Opening  
7
Seat  
Bottom  
Assembly  
• Pull the frame leg out on each frame to open. Make sure it  
5
“clicks” into place.  
Short Leg  
Tube  
• Turn the seat bottom assembly upright.  
• Fit the seat back pins into the openings in the top side of  
the seat bottom assembly.  
#10 x 7/8" Black Screw  
SHOWN ACTUAL SIZE  
Back Base  
Hinge  
Long  
Tapered  
Leg Tube  
Hinge Rod  
8
Front Base  
6
• Identify the back and front base. The back base has short leg  
tubes and the front base has long, tapered leg tubes.You will  
use the back base for the next assembly step.  
• Turn the seat assembly face down.  
• Insert the hinge rod through the hinge on the seat back  
and seat bottom, as shown.  
• Insert a #10 x 7/8" black screw into the hinge rod.  
• Tighten the screw with a Phillips screwdriver.  
Do not over-tighten.  
• Set the seat assembly aside for Assembly step 12.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Frame  
Decorated  
Side  
Seat Height  
Adjusters  
Position 4  
Frame  
Back  
Legs  
Press Lever  
Back Base Hole  
10  
Screw  
Retainers  
• While pressing the levers on the seat height adjusters, lift  
them to position 4 on the frame front legs, as shown.  
Back Base Hole  
9
Seat Assembly  
#10 x 7/8" Black Screw - 2  
SHOWN ACTUAL SIZE  
Screw Retainer - 2  
• Position a frame so that the decorated side is outward.  
• Insert the back leg of a frame into the back base.  
Sockets  
Sockets  
• Fit a screw retainer over the hole in the back base, as shown.  
• Insert a #10 x 7/8" black screw through the screw retainer  
and back base.  
• Tighten the screw with a Phillips screwdriver. Do not  
over-tighten.  
• Repeat this procedure to attach the other frame back leg to  
the other side of the back base.  
Seat Bottom  
Tubes  
11  
Hint: The #10 x 7/8" black screws may have been assembled to  
the screw retainers.  
• Fit the seat assembly between the two frames.  
• Insert the seat bottom tubes into the sockets in each seat  
height adjuster.  
Hints:  
Be sure the seat height adjusters are in the same position  
(position 4).  
You may need to push the frames apart slightly to fit the seat  
bottom tubes into the seat height adjuster sockets.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Push  
Seat  
Push  
Seat  
Height  
Adjuster  
Height  
Adjuster  
Front Leg Hole  
Seat Bottom  
Tube Ends  
13  
Screw Retainers  
Front Leg Hole  
#8 x 3/4" Screw - 2  
SHOWN ACTUAL SIZE  
• Push each seat height adjuster  
to be sure they are completely  
on the seat bottom tubes.  
• Insert a #8 x 3/4" screw through each seat height adjuster  
and the ends of the seat bottom tube.  
• Tighten the screws with a Phillips screwdriver.  
Do not over-tighten.  
Front Base  
12  
#8 x 3/4" Screw - 2  
SHOWN ACTUAL SIZE  
#10 x 7/8" Black Screw - 2  
SHOWN ACTUAL SIZE  
Seat  
Height  
Screw Retainer - 2  
Seat  
Height  
Adjuster  
Adjuster  
• Fit the frame front legs onto the front base.  
• Fit a screw retainer over a hole in the front leg.  
• Insert a #10 x 7/8" black screw through the screw retainer  
and front leg.  
Seat  
Bottom  
Tube Ends  
• Tighten the screw with a Phillips screwdriver. Do not  
over-tighten.  
• Repeat this procedure to secure the other end of the  
front base with the remaining screw retainer and #10 x 7/8"  
black screw.  
14  
Back and  
Bottom View  
Hint: The #10 x 7/8" black screws may have been assembled to  
the screw retainers.  
• From the back and bottom of the assembly, insert a #8 x 3/4"  
screw through both seat height adjusters and the ends of  
the seat bottom tube.  
• Tighten the screws with a Phillips screwdriver.  
Do not over-tighten.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Pad  
Slot  
Elastic Loops  
Crotch  
Belt  
Hole  
Hole  
16  
• Insert the crotch belt through the slot in the pad. Make  
sure the crotch belt is not twisted.  
Front View  
Tabs  
Elastic Loops  
15  
Back and  
Bottom View  
• Lift the assembly upright.  
• From the front of the assembly, place the pad onto the seat.  
• Lift the bottom of the pad. Insert the two elastic loops on  
the pad through the holes in the seat bottom.  
• From the back and bottom of the seat, hook the elastic  
loops to the tabs on the seat.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Upper Shoulder  
Belt Slots  
Shoulder  
Portion  
Shoulder  
Portion  
17  
Lower Shoulder  
Belt Slots  
• Fold the top of the pad down.  
• Remove the shoulder portion of the waist/shoulder belts  
by feeding them through the slots in the seat back.  
18  
• Lift the top of the pad.  
• Thread the waist/shoulder belts through the bottom slots in  
the back of the seat pad.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Securing Your Child  
IMPORTANT! Before each use, inspect this product for  
damaged hardware, loose joints, missing parts or sharp  
edges. DO NOT use if any parts are missing or broken.  
Contact Fisher-Price® for replacement parts and instructions  
if needed. Never substitute parts.  
Pad Strap  
Handle  
Elastic  
Loop  
Elastic  
Loop  
WARNING  
Tab  
Prevent serious injury or death  
from falls or sliding out.  
Belt  
Ends  
Tab  
The child should be secured in  
the high chair at all times by the  
restraining system, either in the  
recline, semi-recline or upright  
position. The restraint belts must  
be adjusted to fit your child snugly.  
The tray is not designed to hold  
the child in the chair.  
19  
Back View  
• From behind the seat, be sure the shoulder portion of the  
waist/shoulder belts are secure in the seat back slots.  
• Hook the elastic loops on each side of the pad onto the tabs  
in the seat back.  
Waist/Shoulder  
Belt  
Waist/Shoulder  
Belt  
Storage  
Caddy  
Frame  
Tab  
Crotch  
Belt  
1
20  
• Place your child in the seat. Position the crotch belt between  
your child’s legs.  
• Fasten both waist/shoulder belts to each side of the crotch  
belt. Make sure you hear a "click" on both sides.  
• Check to be sure the restraint system is securely attached by  
pulling it away from your child. The restraint system should  
remain attached.  
• At an angle, fit the storage caddy onto the tab on  
either frame.  
Assembly is now complete.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Securing Your Child  
Anchored  
End  
Anchored  
End  
A
B
A
B
Free End  
Free End  
Buckle  
2
Tighten  
Loosen  
To tighten the waist belts:  
• Feed the anchored end of the waist belt up through the  
A
buckle to form a loop  
.
B
• Pull the free end of the waist belt  
.
• Repeat this procedure to tighten the other waist belt.  
To loosen the waist belts:  
• Feed the free end of the waist belt up through the buckle to  
4
A
form a loop  
.
• Enlarge the loop by pulling on the end of the loop toward  
the buckle.  
To change shoulder belt slots:  
• From the back of the high chair, push the shoulder portion  
of the waist/shoulder belts through the seat back slots.  
• Pull the anchored end of the waist belt to shorten the free  
B
end of the waist belt  
.
• Repeat this procedure to loosen the other waist belt.  
Shoulder  
Portion  
Hold  
Adjuster  
Slide  
Pull Strap  
Adjuster  
Down  
Down  
3
Tighten  
Loosen  
5
To tighten the shoulder belts: Hold the adjuster and pull the  
front shoulder strap down.  
To loosen the shoulder belts: Slide the adjuster down.  
Note: After adjusting the restraint system to fit your child,  
make sure you pull on it to be sure it is securely fastened.  
• From the front of the high chair, pull the shoulder portion of  
the waist/shoulder belts out and then fit them back through  
the desired shoulder belt slots in the headrest pad, seat pad  
and the seat back. Pull on the belts to be sure they are  
secure in the seat back.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Trays  
WARNING  
Hint: The base tray can be adjusted for your child’s comfort  
two ways (see steps 7 and 8)!  
Prevent serious injury or death  
from falls or sliding out.  
The child should be secured in  
the high chair at all times by the  
restraining system, either in the  
recline, semi-recline or upright  
position. The restraint belts must  
be adjusted to fit your child snugly.  
The tray is not designed to hold  
the child in the chair.  
Base  
Tray  
Release Bar  
Base Tray  
7
• While pushing the release bar on the front of the base tray,  
adjust the base tray forward or backward.  
Armrest  
Armrest  
Base  
Tray  
Squeeze  
Latch  
Squeeze  
Latch  
6
8
• Fit the base tray onto the seat armrests. Push down until  
the base tray "snaps" into place.  
• While squeezing the latches underneath the base tray,  
adjust the base tray forward or backward.  
Hint: Before use, thorougly wash all parts (the trays) that may  
contact food.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Trays  
Hint: The base tray can be removed two ways (see steps  
9 and 10)!  
Food Tray  
Base  
Tray  
Base  
Tray  
Squeeze  
Latch  
Squeeze  
Latch  
11  
9
• Fit the food tray into the base tray, as shown.  
Hint: Before use, thorougly wash all parts (the trays) that may  
contact food.  
• Squeeze one or both of the latches underneath the base  
tray and lift.  
Base  
Tray  
Release  
Bar  
10  
• While pushing the release bar on the front of the base tray,  
pull the tray base towards you and remove.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the Seat  
WARNING  
Hint: Adjust the seat angle to any of three positions: Upright,  
Semi-Recline or Recline.  
Prevent serious injury or death  
from falls or sliding out.  
Upright  
Semi-Recline  
It is recommended that the high  
chair be used in the upright position  
only by children capable of sitting  
upright unassisted.  
Recline  
Hint: Adjust the seat height to any of seven positions!  
Seat Height  
Adjuster  
13  
To adjust the seat angle:  
Press Lever  
• Squeeze the seat back  
handle and push the seat  
back forward or, pull it  
backwards to the  
desired position.  
• Push the seat back to be  
sure it is latched in position.  
Squeeze  
12  
Back View  
To adjust the seat height:  
4
• Press the levers on both seat  
height adjusters and lift or lower  
the seat to the desired height.  
• Make sure both sides of the seat  
are adjusted to the same height.  
Push the seat bottom to be sure the seat is locked in place.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Storage  
Pull Frame  
Release Latch  
Base  
Tray  
Hole  
Peg  
15  
14  
• With the legs all the way open, lower the seat to position 1  
(the lowest position).  
• Pull the frame release latches forward and push the rear legs  
toward the front legs.  
• Fit the holes on the base tray latches onto the pegs on the  
back of the high chair frame.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Care  
For other countries, outside the United States:  
• The pad and headrest are machine washable. Wash the pad  
and headrest separately in cold water on the gentle cycle.  
Do not use bleach. Tumble dry separately on low heat and  
remove promptly.  
Canada: call 1-800-567-7724, or write to: Mattel Canada Inc., 6155  
Freemont Blvd. Mississauga, Ontario L5R 3W2.  
Great Britain: telephone 01628 500302.  
• The frame and base tray may be wiped clean using a mild  
cleaning solution and a damp cloth. Do not immerse the  
base tray.  
Australia: Mattel Australia Pty. Ltd., 658 Church Street,  
Locked Bag #870, Richmond, Victoria 3121 Australia.  
Consumer Advisory Service 1300 135 312.  
• The food trays are dishwasher safe. Simply remove the food  
tray from the base tray and place in your dishwasher.  
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.  
To remove the pad:  
• Remove the four elastic loops from the pegs on the  
underside and back of the seat.  
• Unfasten the pad strap and headrest strap from the  
seat back.  
• Feed the shoulder portion of the waist/shoulder belts  
through the slots in the seat back, the pad and the headrest.  
• Feed the waist portion of the waist/shoulder belts and  
crotch belt down through the slots in the seat.  
• Remove the waist/shoulder belts and crotch belt through  
the slots in the pad.  
• Unfasten the pad fasteners from the front edge of the  
seat bottom.  
• Remove the pad.  
To replace the pad and headrest: refer to Assembly  
steps 15-19.  
IMPORTANT! Never use this product without the  
restraint system. Replace the waist/shoulder belts and  
crotch belt.  
Fisher-Price, Inc., a subsidiary of Mattel, Inc.  
East Aurora, New York 14052, U.S.A.  
©2002 Mattel, Inc. All Rights Reserved.  
® and TM designate U.S. trademarks of Mattel, Inc.  
Printed in China  
79638c-0920  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Cisco Systems Network Router 46 User Manual
Cooper Lighting Indoor Furnishings 196 User Manual
Craftsman Lawn Mower 37763 User Manual
Crate Amplifiers Musical Instrument Amplifier MX15R User Manual
Dukane Stereo Amplifier VP 400 User Manual
Electro Voice Portable Speaker EVS 16B User Manual
Everpure Water System 7DM User Manual
Fundex Games Board Games Bagball User Manual
GE Answering Machine 15298530 User Manual
GE Monogram Range ZET2PM User Manual