T6197
Please keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required. Tools required for assembly:
Phillips Screwdriver, Hammer and Scrap Block of Wood (not included).
Requires three "AA" batteries (included).
Age: 2-6 years.
Weight limit: 60 lbs (27 kg).
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Rear Wheel
(Indented Side Up)
Cap Nut
Hubcap
(Peg Side Down)
Cover
Straight Axle
Frame
Hubcap
Rear Wheel
(Indented Side Down)
Hubcap
(Peg Side Up)
Assembled
Rear Wheel
Straight Axle
Scrap Block
of Wood
Cap Nut
Assembly Tool
3
1
• Turn the frame on its side with the exposed end of the
straight axle up.
• Place the cap nut assembly tool under the assembled rear
wheel and onto the cap nut.
• Slide a hubcap (peg side up) onto the straight axle.
• Slide a rear wheel (indented side down) onto the
straight axle.
• Slide a rear wheel (indented side up) onto the end of the
straight axle.
Frame
• Slide a hubcap (peg side down) onto the straight axle.
• Place a cap nut on the end of the straight axle. Tap the
cap nut with a hammer. Gently pull the rear wheel up
to be sure the cap nut is securely attached to the
straight axle.
• Insert one of the tabs on a cover into a slot in the hubcap.
Push to snap the cover into place. Repeat this procedure
to attach the other cover to the other hubcap.
Hole
Hole
Pedal Hub
Tab
Pedal Axle
Tab
Slot
Straight Axle
Pedal Hub
2
4
BOTTOM VIEW
• Fit two pedal hubs onto the pedal axle tabs. Make sure the
tabs fit into the slot in each pedal hub.
• Turn the frame upside down.
• Insert the straight axle through the holes in the rear of
the frame.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Pedal Hubs
Pedal
Pedal Axle
Front Wheel
Pedal Axle
Hole
5
Scrap Block of Wood
• While holding the pedal hubs
on the pedal axle, insert the
pedal axle through the hole in the center of the front wheel.
• Push the pedal hubs into the center of the front wheel until
they are flush with the surface of the front wheel.
7
• Fit the pedal on the pedal axle. Tap the pedal with
a hammer until it is secure.
• Pull the pedal up to be sure it is secure. If you can remove
it, you have not secured it properly. Tap it with the
hammer again.
Pedal Hub
Fork Arms
Fork Cover
Pedal Hub
Groove
8
6
Pedal Axle
• Place the front wheel assembly between the fork arms.
Make sure the pedal axle fits into the groove at the bottom
of each fork arm.
• Place a fork cover over the pedal axle on one fork arm.
• Insert two #8 x 3/4" screws into the fork cover and tighten.
• Turn the front wheel
assembly over.
• Insert the remaining pedal hubs on top of and below the
pedal axle and into the hole in the center of the front wheel.
• Push the pedal hubs into the center of the front wheel until
they are flush with the surface of the front wheel.
• Repeat this procedure to attach the other fork cover to the
other fork arm.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Handlebar
Basket Mount
Frame
Neck
Fork
Post
11
Fork Cover
Rear of Trike
• Fit the basket mount onto the front of the handlebar.
• Insert four #6 x ½" screws into the holes and tighten.
9
• Insert the fork post up through the hole in the neck of the
frame. Make sure the fork is positioned so that the fork
covers face the rear wheels.
• Place the handlebar onto the fork post and push it down
onto the frame. Make sure the handlebar is positioned so
that the screw hole faces the rear wheels and aligns with
the screw hole in the fork post.
Basket
Hint: You may need to rotate the handlebar to align the holes.
• Insert the #8 x 3" screw through the hole in the handlebar
and into the fork post so that part of the screw (about 3/4")
is still visible. Tighten the screw.
Cap
12
• Fit the basket on the tab on the front of the handlebar assembly.
• Insert two #8 x ¾" screws into the top of the basket
and tighten.
Seat Retainer
Seat
10
• Insert and “snap” the cap into the hole in the frame.
Peg
Holes
13
• Position the seat upside down.
• Fit the small pegs on the seat retainer into the holes in
the seat.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Label Decoration
Attaching the Seat
Hint: The seat can be attached to the frame in any of three
positions, depending on the size of your child. Check
your child’s fit on the trike by observing the seat to pedal
distance, as it is being ridden. If the pedals seem too far
away or too close for your child, move the seat up or down.
(Place label 9 on
opposite side)
12
8
(Place label 13 on
opposite side)
Seat
Tabs
14
(Place label
15 on opposite
side of seat)
Seat
Retainer
2
6
10
(Place
label
11 on
opposite
side)
Slots
7
(Place label 3 on
opposite side)
1
(Place remaining label 1’s on
opposite side of front wheel)
SIDE VIEW
Middle Position
Lower Position
Upper Position
• At an angle, insert the tabs on the seat into any of the top
three sets of slots for the lower, middle or upper position.
• Lower the seat so that the seat retainer inserts and snaps
into the slots in the frame.
• Pull up on the seat to be sure it is secure.
4
5
DASH VIEW
• Make sure the areas where the labels will be applied are
clean and dry. Wipe your vehicle with a clean, soft, dry
cloth to remove any dust or oils.
• For best results, avoid applying a label more than once.
• Apply the labels as shown in the illustration above.
• After applying the label, rub the label firmly with a cloth to
make sure the label is adhered to your vehicle.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Replacement
For best performance, we recommend replacing the batteries that
came with this trike with three, new alkaline "AA" (LR6) batteries.
Battery Compartment
Basket
3
1,5V x 3
“AA” (LR6)
1
Hint: When sound or lights become faint or stop, it's time
for an adult to replace the batteries. We recommend the
use of alkaline batteries for longer battery life.
• Loosen and remove the two screws in the basket.
Remove the basket.
• Loosen the screw in the battery compartment door. Open
the battery compartment door.
Basket Mount
• Insert three "AA" (LR6) alkaline batteries.
• Close the battery compartment door and tighten the screw.
• Replace the basket mount and basket. Replace the screws
and tighten.
• If this product begins to operate erratically, you may need
to reset the electronics. Slide the power switch off and then
back on.
• Protect the environment by not disposing of this
product with household waste (2002/96/EC).
Check your local authority for recycling advice
and facilities (Europe only).
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can
cause a chemical burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
2
• Then, loosen and remove the four screws from the basket
mount. Remove the basket mount.
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always
remove exhausted batteries from the product. Dispose of
batteries safely. Do not dispose of this product in a fire.
The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type,
as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product
before charging.
• If removable, rechargeable batteries are used, they are
only to be charged under adult supervision.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the Seat
Consumer Information
Seat
TANCE
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Seat Retainer Tab
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
Frame
Care
Seat Retainer Tab
• Check the plastic parts regularly and if broken or cracked,
dispose of them properly.
• Check all fasteners regularly to be sure they are tight. If the
fasteners are not tight, tighten them as necessary.
• To clean, use a mild soap and water solution and a clean
cloth. Rinse clean with water to remove soap residue.
• Turn the frame on its side.
• Squeeze the seat retainer tabs toward one another and lift
the seat from the frame.
FCC Statement (United States Only)
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
Let's Go!
IMPORTANT! It is good practice to start training children very
young regarding the importance of helmet use. When children
are older and riding bicycles and faster vehicles, it is important
that they use a helmet each and every time they ride. For this
reason, even while riding a tricycle, it is a good idea to familiarize
your child with helmet use, so that it becomes a habit for life.
Choose a helmet that complies with requirements of the
applicable certifying agency for bicycle helmets.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user’s
authority to operate the equipment.
Music
Weather
Places
to Go
Ignition
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
ICES-003
Sounds
•
This Class B digital apparatus complies with Canadian ICES-003.
• Operation is subject to the following two conditions: (1) this
device may not cause harmful interference and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
Power Switch
Turn Signal
Turn Signal
NMB-003
Horn
• Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
• L’utilisation de ce dispositif est autorisée seulement aux
conditions suivantes : (1) il ne doit pas produire de brouillage
et (2) l’utilisateur du dispositif doit être prêt à accepter tout
brouillage radioélectrique reçu, même si ce brouillage est
susceptible de compromettre le fonctionnement du dispositif.
• Slide the power switch ON.
• Turn the ignition, “VRROOOM!”
• Press the left or right turn signals for flashing blinkers.
• Press any of the buttons for fun sounds!
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|