M6711
WARNING
IMPORTANT!
KEEP INSTRUCTIONS FOR FUTURE REFERENCE.
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Assembly
IMPORTANT! Before assembly and each use, inspect this
product for damaged hardware, loose joints, missing parts or
sharp edges. DO NOT use if any parts are missing or bro-
ken. Contact Mattel for replacement parts and instructions if
needed. Never substitute parts.
IMPORTANT! Please remove all parts from the package
and identify them before assembly. Some parts may be
packed in the pad.
Back Leg
Front Leg
2 Swing Frames
Hint: To allow the product
to swing properly, the swing
arm-to-frame (with power
switch) connection is
designed to be loose.
1
•Slide the front and back legs on the swing frame out until
they “click” into place.
Toy Bar
•Repeat this procedure to open the other swing frame.
Seat Pad
Press Buttons
on Front Legs
Seat Frame
2 Toys
Base Tube
2 Base Tubes
2
•While pressing the buttons on each front leg, insert the
front legs into the base tube.
•Push the front legs down into the base tube until the
buttons “click” into place.
#6 x 2,5 cm Screw – 2
Shown Actual Size
Note: Tighten or loosen all screws with a Phillips
screwdriver. Do not over-tighten the screws.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
PULL UP
PULL UP
Base Tube
Base Tube
3
5
•While standing on the base tube, pull the front legs up. The
front legs should remain secured to the base tube. If you
can remove the front legs, you have not assembled them
correctly to the base tube. Re-read and repeat assembly
step 2.
•While standing on the base tube, pull the back legs up.
The back legs should remain secured to the base tube.
If you can remove the back legs, you have not assembled
them correctly to the base tube. Re-read and repeat
assembly step 4.
Seat Hubs
Seat Frame
Press Buttons
on Back Legs
Base Tube
Frame Hubs
4
•While pressing the buttons on each back leg, insert the
back legs into the remaining base tube.
•Push the back legs down into the base tube until the
buttons “click” into place.
6
•Position the seat frame so that the tubes are upright,
as shown.
•While gently pulling the seat hubs out, fit them to the
matching frame hubs.
Hint: If the hubs do not fit together, simply turn the seat
frame around and try again!
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Pad Lower Pocket
Seat Hub
Seat Hub
Seat Bottom Tube
7
•Insert a screw through the outside of each seat hub.
Tighten the screws.
9
•Fit the pad lower pocket onto the seat bottom tube,
as shown.
Pad Upper
Pocket
Toy Bar
Seat Back Tube
Slots
Waist Belt
Socket
10
•Insert and “snap” the peg on the toybar into the socket
on the swing arm. Pull the toy bar up to be sure it is secure.
•Fit the toy strings up through the slots in the toy bar leaf.
Assembly is now complete.
8
•Fit the pad upper pocket over the seat back tube.
•From behind the assembly, insert the waist belts through
the slots in the pad.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Installation
Battery Safety Information
In exceptional circumstances, batteries may leak fluids
that can cause a chemical burn injury or ruin your
product. To avoid battery leakage:
•Do not mix old and new batteries or batteries of different
types alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
Hint: We recommend using alkaline batteries for
longer battery life.
•Insert batteries as indicated inside the battery compartment.
•Remove batteries during long periods of non-use. Always
remove exhausted batteries from the product. Dispose of
batteries safely. Do not dispose of this product in a fire.
The batteries inside may explode or leak.
1,5V x 4
“C” (LR14)
•Never short-circuit the battery terminals.
•Use only batteries of the same or equivalent type
as recommended.
•Do not charge non-rechargeable batteries.
•Remove rechargeable batteries from the product
before charging.
Note: Low battery power may cause product movement
to slow and sound volume to become faint or turn off all
together. If this should happen, please remove and discard
all four batteries and replace with four, new “C” (LR14)
alkaline batteries.
•If removeable, rechargeable batteries are used, they are
only to be charged under adult supervision.
Battery Compartment Door
•Locate the battery compartment door on the frame.
•Loosen the screws in the battery compartment door.
•Remove the battery compartment door.
•Insert four "C" (LR14) alkaline batteries.
•Replace the battery compartment door and tighten
the screws.
• If this product begins to operate erratically, you may need
to reset the electronics. Slide the power switch off and then
back on.
•Protect the environment by not disposing of the product
with household waste (2002/96/EC). Check your local
authority for recycling advice and facilities (Europe only).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Securing Your Child
Waist Belt
WARNING
To prevent serious injury from
falls and being strangled in the
restraint system:
• Always use the restraint system.
• Not recommended for children who
can sit up by themselves (6 months
approximately, until 9 Kg/20 lbs).
• Never leave child unattended.
• It is dangerous to use this product on
an elevated surface.
Buckle
Restraint Pad
• Never use toy bar as a handle.
•Place your child in the seat. Position the restraint pad
between your child’s legs.
•Fasten both waist belts to the buckles on each side of the
restraint pad. Make sure you hear a “click” on both sides.
•Check to be sure the restraint system is securely attached
by pulling it away from your child. The restraint should
remain attached.
•Tighten each waist belt so that the restraint system is snug
against your child. Please refer to the next section for
instructions to tighten the waist belt.
IMPORTANT! The maximum weight limit for this product
is 9 kg (20 lbs). If your child weighs less han 9 kg (20 lbs),
but is really active and appears to be able to climb out of
the swing, immediately discontinue its use.
Anchored End
Anchored End
Free End
Free End
TIGHTEN
LOOSEN
To tighten the belts: Feed the anchored end of the belt up
through the buckle to form a loop . Pull the free end of
the belt . Repeat this procedure to tighten the other belt.
To loosen the belts: Feed the free end of the belt up
through the buckle to form a loop . Enlarge the loop by
pulling on the end of the loop toward the buckle. Pull the
anchored end of the belt to shorten the free end of the belt
. Repeat this procedure to loosen the other belt.
Please Note: After adjusting the belts to fit your child, make
sure you pull on them to be sure they are securely fastened.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Swinging and Music
Storage
Music Switch
Power Switch
•Place your child in the seat and secure properly.
Hint: After turning on power, this product may not swing
unless there is a child in the seat.
•Slide the power switch to any of five speed settings.
•Give the seat a light push to start the swinging motion.
Adjust the power switch to the desired swing motion setting.
Hint: As with most battery-powered swings, a heavier child
will reduce the amount of swinging motion on all settings.
In most cases, the low setting works best for a smaller child
while the high setting works best for a larger child.
•If swinging stops while using a lower setting, try a higher
setting. Give the seat a light push to start the swinging
motion again.
•Slide the music switch to on with low volume ; on with
high volume
•Be sure to turn this product off when not in use. Slide
the power switch to the off setting
or off
.
.
•Make sure your child is properly secured in the swing seat.
•Grasp both handles, as shown, and lift.
•Carefully carry the swing to another room. Be sure to set
the swing down on a non-elevated, flat surface.
•Lift the seat bottom.
•Press the frame release buttons on the inside of the frames
and push the front legs inward.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|