Fisher Marine GPS System 00275 8026 0001 User Manual

MAN 4275A00  
PN: 00275-8026-0001  
English  
July 2000  
HART® Communicator  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
Introduction........................................................................................ 1-1  
Liquid Crystal Display (LCD) ............................................................. 1-5  
The Action Keys ................................................................................ 1-5  
On/Off Key ................................................................................ 1-5  
Up Arrow Key ............................................................................ 1-6  
Down Arrow Key ....................................................................... 1-6  
Hot Key ..................................................................................... 1-6  
Software-Defined Function Keys....................................................... 1-6  
Alphanumeric and Shift Keys ............................................................ 1-8  
Software Icons ........................................................................ 1-10  
Reviewing Installed Devices ................................................... 1-12  
Main Menu....................................................................................... 1-12  
Offline Menu.................................................................................... 1-13  
New Configuration (Offline)..................................................... 1-14  
From Blank Template Menu............................................ 1-15  
Saved Configuration Menu (Offline)........................................ 1-17  
Data Pack Contents Menu .............................................. 1-17  
Saved Configuration Menu (data pack Contents) ........... 1-18  
Online Menu.................................................................................... 1-19  
Frequency Device Menu ................................................................. 1-22  
Utility Menu...................................................................................... 1-22  
Configure Communicator Menu .............................................. 1-22  
Polling Menu ................................................................... 1-23  
Contrast Menu................................................................. 1-24  
Off Time Menu ................................................................ 1-24  
Ignore Diagnostics Menu ................................................ 1-25  
i
Download from Www.Somanuals.com. All Manuals Search And Download.  
System Information Menu ....................................................... 1-26  
Listen for PC Menu ................................................................. 1-26  
Storage Location Menu........................................................... 1-28  
Simulation Menu ..................................................................... 1-28  
Saving a Connected Device Configuration...................................... 1-29  
Using the Hot Key ........................................................................... 1-30  
Customizing the Hot Key Menu............................................... 1-31  
Adding Options to the Hot Key Menu...................................... 1-31  
Deleting Options from the Hot Key Menu................................ 1-33  
Editing the Date....................................................................... 1-34  
Servicing the HART Communicator ................................................ 1-35  
Using a Battery Pack............................................................... 1-35  
Using a Memory Module ......................................................... 1-37  
Installing and Removing the Data Pack 100 ........................... 1-39  
Common Tasks for Fisher-Rosemount HART  
Devices ............................................................................. 2-1  
Introduction........................................................................................ 2-1  
Powering Up Online .......................................................................... 2-1  
Online Menu...................................................................................... 2-2  
Device Setup............................................................................. 2-2  
Primary Variable (PV) ............................................................... 2-3  
Analog Output (AO)................................................................... 2-3  
Lower Range Value (LRV) ........................................................ 2-3  
Upper Range Value (URV)........................................................ 2-3  
Device Setup Menu........................................................................... 2-4  
Process Variables ..................................................................... 2-4  
Diag/Service.............................................................................. 2-4  
Basic Setup ............................................................................... 2-5  
Detailed Setup........................................................................... 2-5  
Review ...................................................................................... 2-6  
Fast Key Sequences ......................................................................... 2-6  
ii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Trees....................................................................... 3-1  
Introduction........................................................................................ 3-1  
Model 54pH/ORP Transmitter ......................................................... 3-2  
Model 333 HART® Tri-Loop Converter............................................ 3-3  
Model 644 Temperature Transmitter................................................ 3-4  
Model 1151 Pressure Transmitter.................................................... 3-5  
Model 2081C Conductivity Transmitter ............................................ 3-6  
Model 2081pH Transmitter............................................................... 3-7  
Model 2088 Pressure Transmitter.................................................... 3-8  
Model 2090 Pressure Transmitter.................................................... 3-9  
Model 3001S Hydrostatic Transmitter............................................ 3-10  
Model 3044C Temperature Transmitter ......................................... 3-11  
Model 3051 Pressure Transmitter.................................................. 3-12  
Model 3051C Pressure Transmitter (Original)................................ 3-13  
Model 3081C Conductivity Transmitter .......................................... 3-14  
Model 3081FG Oxygen Analyzer ................................................... 3-15  
Model 3081pH Transmitter.............................................................. 3-16  
Model 3095C Level Controller........................................................ 3-17  
Model 3095MV Multivariable Transmitter....................................... 3-18  
Model 3144 Temperature Transmitter............................................ 3-19  
Model 3201 Hydrostatic Interface Unit ........................................... 3-20  
Model 3202 Smart Application Module........................................... 3-21  
Model 3244 Temperature Transmitter............................................ 3-22  
Model 3680 Density Transmitter .................................................... 3-23  
Model 3809/3810 Variable Area Meter........................................... 3-24  
Model 4000 Oxygen Analyzer ........................................................ 3-25  
Model 8712C Mag Flow Transmitter .............................................. 3-26  
Model 8712C+ Mag Flow Transmitter............................................ 3-27  
Model 8712U+ Mag Flow Transmitter............................................ 3-28  
Model 8800 Vortex Flowmeter ....................................................... 3-29  
Model 9701 Mass Flowmeter ......................................................... 3-30  
Model 9712 Mass Flowmeter ......................................................... 3-31  
Model 9739 Mass Flowmeter ......................................................... 3-32  
iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model APEX Radar Level Gauge................................................... 3-33  
Model ProBarTM DP Flowmeter .................................................... 3-34  
Model ProBarTM UC Flowmeter .................................................... 3-35  
Model Tri-20/9000 Oval Flowmeter................................................ 3-36  
Model WC3000 Oxygen Analyzer .................................................. 3-37  
Specifications and Ordering Information........................... B-1  
Functional Specifications.................................................................. B-1  
Performance Specifications.............................................................. B-2  
Physical Specifications..................................................................... B-2  
Ordering Information ........................................................................ B-3  
Spare Parts .............................................................................. B-4  
CSA and FM Intrinsic Safety Approvals........................... C-1  
Canadian Standards Association (CSA) .......................................... C-1  
Factory Mutual (FM)......................................................................... C-2  
Troubleshooting Communication Problems ..................... D-1  
If you are still having problems......................................................... D-3  
Index .................................................................................. I-1  
iv  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIST OF ILLUSTRATIONS  
Figure Number  
Title  
1-1. The HART Communicator. .......................................................... 1-1  
1-2. Rear Connection Panel with NiCad Recharger Jack. ................. 1-2  
1-3. Connecting to the Transmitter Comm Terminals. ....................... 1-3  
1-4. Connecting the HART Communicator to the Loop. ..................... 1-3  
1-5. Connecting the HART Communicator with the Load Resistor. ... 1-4  
1-6. HART Communicator Alphanumeric and Shift Keys. .................. 1-8  
1-7. Quickly Accessing Menus. .......................................................... 1-8  
1-8. Powering Up Offline or Online. .................................................. 1-10  
1-9. Menu Icons and Associated Keys. ............................................ 1-10  
1-10. Main Menu. ............................................................................... 1-12  
1-11. Offline Menu Tree. .................................................................... 1-13  
1-12. Offline Menu. ............................................................................. 1-14  
1-13. From Blank Template Menu. ..................................................... 1-15  
1-14. Edit Individually Menu. .............................................................. 1-15  
1-15. Unit Variable Menu. ................................................................... 1-15  
1-16. Save As... Menu. ....................................................................... 1-16  
1-17. Location Menu. ......................................................................... 1-16  
1-18. Saved Configuration Menu (Offline). ......................................... 1-17  
1-19. Data Pack Contents Menu. ....................................................... 1-17  
1-20. Saved Configuration Menu (data pack Contents). .................... 1-18  
1-21. Online Menu. ............................................................................. 1-19  
1-22. Generic Online Menu Tree. ....................................................... 1-21  
1-23. Frequency Device Menu. .......................................................... 1-22  
1-24. Utility Menu. .............................................................................. 1-22  
1-25. Configure Communicator Menu. ............................................... 1-22  
1-26. Polling Menu. ............................................................................ 1-23  
1-27. Contrast Menu. .......................................................................... 1-24  
1-28. Off Time Menu. ......................................................................... 1-24  
1-29. Ignore Diagnostics Menu. ......................................................... 1-25  
ix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-30. Delete Configurations Menu. ..................................................... 1-25  
1-31. System Information Menu. ........................................................ 1-26  
1-32. Listen for PC Menu. .................................................................. 1-26  
1-33. Storage Location Menu. ............................................................ 1-28  
1-34. Sample Hot Key Menu. ............................................................. 1-30  
1-35. Hotkey Configuration Menu. ...................................................... 1-31  
1-36. Adding a Hot Key Option. .......................................................... 1-32  
1-37. Marking a Read-Only Hot Key Option. ...................................... 1-32  
1-38. Hot Key Menu. .......................................................................... 1-32  
1-39. Variable Display Option. ............................................................ 1-33  
1-40. Deleting a Hot Key Option. ........................................................ 1-33  
1-41. Date Menu. ............................................................................... 1-34  
1-42. HART Communicator Exploded View. ...................................... 1-35  
1-43. Battery Pack Removal. .............................................................. 1-36  
1-44. Memory Module Replacement. ................................................. 1-38  
1-45. Data Pack 100 Installation and Removal. ................................. 1-39  
2-1. Online Menu. ............................................................................... 2-2  
2-2. Device Setup Menu. .................................................................... 2-4  
2-3. Diagnostics and Service Menu. ................................................... 2-4  
2-4. Basic Setup Menu. ...................................................................... 2-5  
2-5. Sample Fast Key Sequence. ....................................................... 2-6  
LIST OF TABLES  
Table Number  
Title  
Page  
1-1. Function Key Labels. ................................................................... 1-7  
1-2. Main Options for the PC AMS Interface.......................................1-27  
x
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION 1  
The HART® Communicator  
INTRODUCTION  
The HART (Highway Addressable Remote Transducer) Communicator  
(Figure 1-1) is a hand-held interface that provides a common communication  
link to all HART-compatible, microprocessor-based instruments.  
Section 1 discusses the HART Communicator Connections, Liquid Crystal  
Display, Keypad, Offline and Online menu, Battery Pack, Memory Module,  
data pack 100, Maintenance, and Year 2000 Compatibility. It also includes  
short overviews on some of the Communicator’s functionality.  
Section 2 describes tasks that are common to Fisher-Rosemount’s HART  
devices and includes some of the common screen displays.  
Section 3 displays typical examples of menu trees specific to Fisher-  
Rosemount products.  
Your HART Communicator interfaces with any HART-compatible device from  
any wiring termination point using a 4–20 mA loop, provided a minimum load  
resistance of 250 ohms is present between the Communicator and the power  
supply. Your HART Communicator uses the Bell 202 frequency shift key  
(FSK) technique of high-frequency digital signals superimposed on a  
standard transmitter current loop of 4–20 mA. Because the total high-  
frequency signal voltage added to the loop amounts to zero, communication  
to and from a HART-compatible device does not disturb the 4–20 mA signal.  
LIQUID CRYSTAL DISPLAY (LCD)  
FUNCTION KEYS  
ACTION KEYS  
ALPHANUMERIC KEYS  
SHIFT KEYS  
FIGURE 1-1. The HART Communicator.  
1-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
HART COMMUNICATOR CONNECTIONS  
The HART Communicator can interface with a transmitter from the control  
room, the instrument site, or any wiring termination point in the loop through  
the rear connection panel (Figure 1-2).  
To interface, connect the HART Communicator with the appropriate  
connectors in parallel with the instrument or load resistor. All connections are  
non-polarized. When connecting to a PC, you must use the PC  
Communication Adapter to connect to the Communicator’s serial port. See  
Listen for PC Menu on page 1-26 for more information and Appendix B for  
a complete list of parts.  
For intrinsically safe Canadian Standards Association (CSA) and Factory  
Mutual (FM) wiring connections, see Appendix C.  
!
WARNING  
Explosions can result in death or serious injury. Do not connect to the serial port  
or NiCad recharger jack in an explosive atmosphere.  
Loop Connectors  
Serial Port  
Optional NiCad  
Recharger Jack  
FIGURE 1-2. Rear Connection Panel with NiCad Recharger Jack.  
1-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
NOTE: For the HART Communicator to function properly, a minimum of 250  
ohms resistance must be present in the loop. The HART Communicator  
does not measure loop current directly.  
Figure 1-3 and Figure 1-4 illustrate typical wiring connections between the  
HART Communicator and any compatible device.  
HART-compatible  
Device  
RL250 _  
+
+
+
_
_
+
_
+
mA  
Power  
Supply  
_
_
+
Current  
Meter  
FIGURE 1-3. Connecting to the Transmitter Comm Terminals.  
Device  
+
RL250 Ω  
_
+
+
_
+
_
+
Power  
Supply  
mA  
_
_
_
+
Current  
Meter  
FIGURE 1-4. Connecting the HART Communicator to the Loop.  
1-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
!
WARNING  
Explosions can result in death or serious injury. Before connecting the HART  
Communicator in an explosive atmosphere, make sure the instruments in the  
loop are installed in accordance with intrinsically safe or nonincendive field  
wiring practices. For intrinsically safe CSA and FM wiring connections, see  
Appendix C.  
Figure 1-5 shows how to connect the optional 250 ohm load resistor.  
NOTE: To temporarily install the optional 250 ohm Load Resistor:  
1. Insert the load resistor into the lead set jacks.  
2. Open the loop to allow connection of the resistor in series in the loop.  
3. Close the loop using the lead set connectors.  
+
Power  
Supply  
+
Optional 250 Ohm  
Load Resistor  
HART-compatible Device  
FIGURE 1-5. Connecting the HART Communicator with the Load Resistor.  
1-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
LIQUID CRYSTAL DISPLAY (LCD)  
The LCD is an 8-line by 21-character display that provides communication  
between you and the connected device. When you connect to a HART-  
compatible device, the top line of each Online menu displays the model  
name of the device and its tag. The bottom line of each menu is reserved for  
the dynamic labels for each software-defined function key, F1-F4 (found  
directly below the display).  
These dynamic labels display available functions. For example, the label  
HELP appears above the F1 key when access to online help is available.  
See Software-Defined Function Keys on page 1-6 for more information.  
The Communicator does not store key strokes in its memory. The LCD  
should be fully displayed before you press a key to do the next action.  
THE ACTION KEYS  
The action keys (Figure 1-1) are the six blue, white, and black keys located  
above the alphanumeric keys. The function of each key is described as  
follows:  
On/Off Key  
Use this key to power up and power off the HART Communicator.  
When you power up the Communicator, it automatically searches for  
a HART-compatible device on the 4-20 mA loop. If a device is not found, the  
Communicator displays the message “No Device Found. Press OK....” Press  
the OK ‘F4’ function key and the Main menu displays on the screen. See  
Main Menu on page 1-12.  
If a HART-compatible device is found, the Communicator displays the Online  
menu. See Online Menu on page 1-19.  
Refer to Getting to Know the HART Communicator on page 1-9,  
Section 3, or your device-specific manual for more information about Online  
menu options.  
You can select the Polling option to direct the HART Communicator to look  
for devices at multidrop addresses. See Polling Menu on page 1-23 for  
details.  
During certain operations, the message “OFF KEY DISABLED” indicates  
that you cannot turn the HART Communicator off. This feature helps you  
avoid unintentionally turning off the power to the HART Communicator while  
the output of a device is fixed or when you are editing a device variable.  
1-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Up Arrow Key  
Use this key to move the cursor up through a menu or list of options.  
You can also use it to scroll through lists of available characters  
when editing fields that accept both alpha and numeric data.  
Down Arrow Key  
Use this key to move the cursor down through a menu or list of  
options. You can also use it to scroll through lists of available  
characters when editing fields that accept alpha and numeric data.  
Left Arrow and Previous Menu Key  
Use this dual-function key to move the cursor to the left or back  
to the previous menu.  
Right Arrow and Select Key  
Use this dual-function key to move the cursor to the right or to select  
a menu option.  
Hot Key  
Use this key to quickly access important, user-defined options when  
connected to a HART-compatible device. When the HART  
Communicator is turned off, press the Hot Key to automatically power up and  
display your predefined Hot Key menu. When powered up online, press the  
Hot Key to immediately display the Hot Key menu.  
See Using the Hot Key on page 1-30 for more information.  
SOFTWARE-DEFINED FUNCTION KEYS  
Use the four software-defined function keys located below the LCD, marked  
F1 through F4, to perform software functions as indicated by the dynamic  
labels. On any menu, the label appearing above a function key indicates the  
function of that key for the current menu. As you move among menus,  
different function key labels appear over these four keys. For example, in  
menus providing access to online help, the HELP label appears above the F1  
key.  
1-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                       
In menus providing access to the Home menu, the HOME label appears  
above the F3 key. When the HOME label displays, press F3 to return directly  
to the Online menu. Press BACK (F3) to return to the screen from which  
HOME was pressed.  
Table 1-1 describes the labels that appear above each function key  
throughout the various Communicator menus.  
TABLE 1-1. Function Key Labels.  
F1  
F2  
F3  
F4  
ON/OFF  
Activate or  
deactivate  
a bit-enumerated  
binary variable  
OK  
HELP  
Access online  
help  
ABORT  
Terminate current  
task  
Acknowledge  
information on  
screen  
DEL  
RETRY  
Try to re-establish  
communication  
ESC  
Leave a value  
unchanged  
ENTER  
Accept user-  
entered data  
Delete current  
character or Hot  
Key menu item  
QUIT  
Terminate session  
because of a  
communication  
error  
EXIT  
Leave the current  
menu  
SEND  
Send configuration  
data to device  
EXIT  
Leave the current  
menu  
YES  
Answer yes/no  
question  
PGUP  
Move up one help  
screen  
PGDN  
Move down one  
help screen  
NO  
Answer yes/no  
question  
ALL  
PREV  
NEXT  
Go to next message  
in a list of  
ONE  
Include current  
Hot Key item on  
Hot Key menu for  
all devices  
Go to previous  
message in a list of  
messages  
Include Hot Key  
item for one device  
messages  
NEXT  
Go to the next  
variable in offline  
edit  
SAVE  
HOME  
Go to the top menu  
in the device  
Save information to  
Memory Module or  
data pack  
description  
MARK  
Toggle marked  
configuration  
variables for  
sending to a field  
device  
FILTR  
Open  
customization  
menu to sort  
configurations  
BACK  
Go back to the  
menu from which  
HOME was pressed  
XPAND  
Open detailed  
configuration  
information  
EDIT  
Edit a variable value  
CMPRS  
ADD  
Close detailed  
configuration  
information  
Add current item to  
Hot Key menu  
1-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
ALPHANUMERIC AND SHIFT KEYS  
The 12 alphanumeric keys (Figure 1-6) perform two functions — the fast  
selection of menu options and data entry. Three shift keys enable use of the  
upper row of characters on each alphanumeric key.  
FIGURE 1-6. HART Communicator Alphanumeric and Shift Keys.  
Using the Fast Select Feature  
From within any menu, you can select available options in two ways: 1) you  
can use the up and down arrow keys and the select key to access available  
options, 2) you can use the fast select feature. To fast select the desired  
option, press the corresponding number on the alphanumeric keypad.  
Figure 1-7 shows how to quickly access the Utility menu from the Main  
menu by pressing the indicated fast key.  
J K L  
4
Press this  
key  
To fast select  
this menu  
choice  
FIGURE 1-7. Quickly Accessing Menus.  
1-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Using Shift Keys for Data Entry  
Some menus require data entry. Use the up and down arrow keys when  
available, or use the alphanumeric and shift keys to enter the alphanumeric  
information into the HART Communicator.  
If you press only the alphanumeric key within an edit menu, only the bold  
character in the center of the key will display. These large characters include  
the numbers zero through nine, the decimal point (.), and the dash  
symbol (-). To enter the other characters on the keys, first press and release  
the shift key corresponding to the position of the desired character on the key  
and then press the alphanumeric key. Do not press the keys simultaneously.  
For example, to enter the letter “R” press the following key sequence:  
P Q R  
6
Press the right shift key to activate the shift function; the right shift arrow icon  
appears in the upper right corner of the display. With right shift activated,  
press the 6 key; an “R” appears in the editable field. Press the shift key again  
to deactivate the shift function.  
GETTING TO KNOW THE HART COMMUNICATOR  
The HART Communicator is generally used in two environments — offline  
(not connected to a device) and online (connected to a device). The first  
menu displayed when you power up the Communicator is different for offline  
and online.  
Powering up the Communicator when it is not connected to a device displays  
the message “No Device Found.” Press OK and the Main menu appears.  
Powering up the Communicator when it is connected to a device displays the  
Online menu for the device. From the Online menu, you can access the Main  
menu by pressing the left-arrow key. See Figure 1-8.  
1-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
5ø  
12.øø  
ø
1øø  
Online Menu  
Main Menu  
FIGURE 1-8. Powering Up Offline or Online.  
Software Icons  
The HART Communicator menus display icons that represent specific keys  
on the keypad. Figure 1-9 shows examples of these.  
HART communication:  
Blinking  
indicates ongoing  
communications (HART  
messages are presently being  
transmitted or received).  
Blinking  
indicates the  
device is configured in the  
burst mode.  
Indicates shift is active  
Low battery  
Access  
previous  
menu  
Access additional  
menu items  
HOME  
Access highlighted  
menu item  
FIGURE 1-9. Menu Icons and Associated Keys.  
1-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Learning the Menu Structure  
The following steps show you how to power up the Communicator offline,  
move through the menu structure, and then turn off the Communicator:  
Turn the HART Communicator on.  
Access the Utility menu by  
pressing  
three times  
and then pressing  
Access the Configure  
Communicator menu from  
the Utility menu by pressing  
Access the Contrast menu by  
pressing  
once and  
then pressing  
Press ESC (F3) to return to the  
Configure Communicator menu.  
Press  
two times to return to the Main menu.  
Turn the HART Communicator off.  
1-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Reviewing Installed Devices  
The HART Communicator Memory Module contains device descriptions for  
specific HART-compatible devices. These descriptions enable the  
Communicator to recognize particular devices. The device types can be  
found in the Offline menu under New Configurations.  
If you cannot find a specific HART-compatible device on your Communicator,  
the device revision you are looking for is not programmed into the Memory  
Module. In this instance, you are limited to what is available using the  
generic interface built into your HART Communicator.  
To review the device descriptions programmed into your HART  
Communicator:  
STU  
1
1. From the Main menu, press  
to access Offline menu.  
STU  
1
2. From the Offline menu, press  
to access the list of device  
descriptions programmed into your HART Communicator. The  
Manufacturer menu displays a list of each manufacturer with device  
descriptions currently installed in your Communicator’s Memory Module.  
The standard 12 MB Memory Module is recommended, as it allows for  
more device descriptions.  
3. Select a manufacturer, and the Model menu displays, containing a list of  
currently installed device models provided by the selected manufacturer.  
4. Review the different manufacturers and models to determine the installed  
HART-compatible devices in your Communicator.  
MAIN MENU  
If the HART Communicator is powered up when it is not connected to a  
device, the first menu to appear after the “Device Not Found” message is the  
Main menu (Figure 1-10).  
FIGURE 1-10. Main Menu.  
1-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
If the Communicator is powered up when it is connected to a device, you can  
access the Main menu by pressing the previous menu key. Depending on  
the current online menu, you may need to press the previous menu key  
several times or the HOME key plus  
to return to the Main menu.  
OFFLINE MENU  
From the Main menu, press 1 to access the Offline menu. From the Offline  
menu you can access the options: New Configuration and Saved  
Configuration. Figure 1-11 shows a menu tree for the Offline functions.  
A HART-compatible device does not have to be connected to use the offline  
options, except when sending saved configuration data to a connected  
device.  
Offline Menu  
1. New Config  
2. Saved Config  
Saved Configuration  
1
2
3
Module  
data pack  
PC  
Manufacturer  
Listing  
Name  
Model ID  
Listing  
Saved Configuration  
1
2
3
4
5
6
7
Edit  
Copy to...  
Send  
Print  
Delete  
Rename  
Compare  
Field Device Rev  
Listing  
Edit  
From Blank Template  
Edit  
1
2
3
4
Mark All  
1
2
3
4
Mark All  
Unmark All  
Edit individually  
Save As...  
Unmark All  
Edit individually  
Save As...  
Configuration  
Variables  
Save as...  
1
2
3
Location  
Name  
Data Type  
Data Type  
Location  
1
2
Module  
1
2
3
Standard  
Partial  
Full  
data pack  
FIGURE 1-11. Offline Menu Tree.  
1-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
New Configuration (Offline)  
Use this option to compile a custom set of device configuration data for  
downloading to any HART-compatible device. You can download repeatedly  
to multiple devices so that they store identical configuration data.  
Offline configuration may not be available for all devices. Steps 2 and 3  
below will help you verify if the desired manufacturer and device model are  
programmed into the Communicator’s Memory Module.  
STU  
1
1. Press  
on the Main menu to access the Offline menu. This menu  
allows you to enter a new device configuration or edit a saved device  
configuration.  
To enter a new configuration, go to Step 2.  
To edit a saved configuration, press 2 and go to Saved Configuration  
Menu (Offline) on page 1-17.  
FIGURE 1-12. Offline Menu.  
2. From the Offline menu, press 1. The Manufacturer menu displays a list of  
manufacturers with device descriptions currently installed in your HART  
Communicator.  
3. Select a manufacturer; the Model menu displays. The Model menu  
contains a list of the currently installed device models provided by the  
manufacturer.  
4. Select a device model for configuration; the Field Device Revision (Fld dev  
rev) menu displays. The Fld dev rev menu contains the currently installed  
software revisions for the field device and device descriptions (DD) for the  
model you selected from the previous screen.  
5. Select a device revision; the From Blank Template menu (Figure 1-13)  
displays.  
If you are unsure of the device revision, connect the HART Communicator  
to the device and determine its device revision level. You can access this  
information from the Online menu>Device Setup>Detailed Setup>Device  
Information. See your device manual for more information.  
1-14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
From Blank Template Menu  
To access From Blank Template Menu, see steps 2 through 5 under New  
Configuration (Offline) on page 1-14.  
FIGURE 1-13. From Blank Template Menu.  
The following options are available from the From Blank Template menu:  
Mark all flags all configurable variables to be sent to a HART-compatible  
device. Configuration variables are those that appear when you edit  
variables in the configuration using the Edit Individually option.  
Unmark all removes the flags from all configurable variables in the  
configuration. Unmarked configuration variables are not sent to a connected  
HART-compatible device.  
Edit individually (Figure 1-14) opens the Edit Individually menu containing  
numerous configuration variables.  
FIGURE 1-14. Edit Individually Menu.  
For example, to change the engineering units from inH20 to ftH20, find the  
configuration variable, press the Edit function key, highlight the new unit, and  
press the ENTER function key. The Esc key returns you to the previous  
screen as displayed in Figure 1-15. When you are done, press the EXIT  
function key to return to the From Blank Template menu.  
FIGURE 1-15. Unit Variable Menu.  
1-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Save as... saves your new configuration to either the Memory Module or the  
data pack 100. See Figure 1-16 and Figure 1-17. The Memory Module  
holds up to 10 typical configurations, and contains the operating system  
software, and device application software in nonvolatile memory. The data  
pack stores up to 100 typical configurations in nonvolatile removable  
memory.  
FIGURE 1-16. Save As... Menu.  
FIGURE 1-17. Location Menu.  
You can also use the Save As... menu to enter or edit the configuration name  
and data type. Data Type Standard provides a Data Type menu with editable  
options. Standard is the set of editable variables used when defining a new  
device configuration. Partial is a set of marked variables. Full is the set of all  
device variables.  
NOTE: Configurations created offline in the HART Communicator will not  
transfer to Asset Management Solutions (AMS) software; however, ‘Full’  
configurations saved from a field device to a HART Communicator may be  
uploaded to AMS. Configurations saved as ‘Full’ from an online device may  
also be transferred directly to AMS.  
After you have made all desired changes, save your new configuration to a  
storage location and return to the Offline menu. Refer to Storage Location  
Menu on page 1-28 for more information.  
1-16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Saved Configuration Menu (Offline)  
You can access configuration data already stored in your Communicator  
through the offline Saved Configuration menu.  
To access configuration data stored in your HART Communicator:  
1. Press 1 on the Main menu to access the Offline menu.  
2. Press 2 from the Offline menu, and the Saved Configuration menu screen  
displays (Figure 1-18).  
FIGURE 1-18. Saved Configuration Menu (Offline).  
3. Select either Module Contents or data pack Contents, as appropriate, to  
open your stored configurations. Both storage locations list all saved  
configurations by assigned Tag. See Xpand on page 1-18 for more  
configuration identification details.  
The PC option is not operational with this release. Refer to Listen for PC  
Menu on page 1-26 for details on interfacing with a PC.  
Data Pack Contents Menu  
Figure 1-19 shows the data pack Contents menu, displaying a listing of  
device configurations stored in the data pack. From the Saved Configuration  
menu (Figure 1-18), press 2 to access the data pack Contents menu.  
FIGURE 1-19. Data Pack Contents Menu.  
The following functions keys are available from the data pack Contents  
menu:  
The  
function key opens a menu that provides Sort and Filter options  
FILTR  
for customizing your view of saved device configurations. Sort lets you group  
and display device configurations according to your choice of Tag,  
Descriptor, or Name. Tag Filter lets you view information according to what  
1-17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
you entered with Sort by picking characters from the device Tag, Descriptor,  
or Name.  
When setting up a filter, you can use the period (.) to replace a single  
character of any value or the asterisk (*) to replace zero or more  
alphanumeric characters of any value.  
For example, if you enter A-*-.1, it should match all device tags starting with  
A-, followed by any characters, followed by -, followed by any single  
character, and ending with a 1. That means only devices starting with A-  
and ending in 1, out of your list of saved device configurations, will display as  
a group on the Communicator’s screen.  
XPAND  
The  
function key allows you to view the Tag, Descriptor, and Name  
for the current configuration. Select Compress to return to the previous  
compressed screen with the current Tag or Descriptor or Name.  
Saved Configuration Menu (data pack Contents)  
From the data pack Contents menu (Figure 1-19), press  
Saved Configuration menu (Figure 1-20).  
to open the  
FIGURE 1-20. Saved Configuration Menu (data pack Contents).  
The following functions are available from the Saved configuration menu:  
Edit displays the Edit menu. These edit functions are the same as described  
under Edit individually on page 1-15. If you are editing online, remember  
that only stored data can be edited. A Partial configuration can be edited, but  
you must convert it to a Standard configuration in order to save your edits.  
Copy to... specifies the storage location where you want the copy to be  
stored. You can also change the configuration name when using this option.  
Send sends your saved configuration to a connected device.  
Print requires AMS running in your computer. This option is intended for the  
future. See Listen for PC Menu on page 1-26 for more information.  
Delete removes a saved configuration from the memory storage location. A  
confirmation message will appear. Press Yes or No to complete the function.  
1-18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
Rename accesses the Configuration Name editing menu. After making  
name changes, enter and save the data to return to the previous storage  
location menu.  
Compare compares a selected device configuration from a stored location  
with another device configuration. The HART Communicator compares  
device types, variables, marked lists, etc. Messages will appear indicating  
whether the configurations compared are the same or different. Press OK to  
return to the storage location and your list of device configurations. Find and  
make any necessary changes resulting from your comparisons.  
In order to produce a “Same / Differ” result, the following conditions must be  
met when comparing two configurations:  
1. Device type (including manufacturer), device type number, device revi-  
sion, and DD revision must match exactly.  
2. Configurations can only be compared against other configurations  
containing the same set of variables. The Communicator will notify you if  
this condition is not met.  
3. The format of data storage must match exactly. The Communicator will  
notify you if this condition is not met.  
User assigned configuration names are not considered, as they will differ.  
ONLINE MENU  
VWX  
2
With a HART-compatible device connected, press  
on the Main menu  
to access the Online menu (Figure 1-21).  
5ø  
12.øøø  
FIGURE 1-21. Online Menu.  
The Online menu displays the name of the device on the first line of the LCD.  
You have complete functionality for a specific device only when that device  
description is present in the HART Communicator. If the DD is not present in  
the HART Communicator, contact your nearest service representative.  
The Online menu can be different depending on the connected device. See  
your device-specific manual for Online menu details. Or, see Section 3 for a  
selection of device-specific menu trees.  
1-19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
When the DD for a specific device is not available, your HART  
Communicator provides a generic interface. This generic interface enables  
you to perform functions common to all HART-compatible devices.  
Figure 1-22 shows the Generic Online menu tree.  
The Online (Generic) menu is the first menu in the generic interface. This  
menu displays critical, up-to-date device information such as the process  
variable (PV), analog output (AO), lower range value (LRV), and upper range  
value (URV). Configuration parameters for the connected device are  
accessed using the Device setup option.  
The following functions are available from the Generic Online menu:  
The SAVE function key allows you to save a configuration from a  
transmitted device. See Changing a Saved Configuration on page 1-29 for  
more details.  
Device Setup accesses the Device Setup menu, containing configurable  
device parameters common to all HART-compatible devices.  
PV (Primary Variable) displays the dynamic PV and the related engineering  
units. When the PV contains too many characters to display on the Online  
menu, press 1 to access the PV menu and view the PV and related  
engineering units.  
AO (Analog Output) and related engineering units are displayed on the  
Online menu. The AO is the signal on the 4–20 mA scale that corresponds to  
the PV. When the analog output contains too many characters to display on  
the Online menu, press 3 to access the PV AO menu and view the AO output  
and related engineering units.  
Current LRV (Lower Range Value) and related engineering units are  
displayed on the Online menu. When the LRV contains too many characters  
to display on the Online menu, press 4 to access the PV LRV menu and view  
the LRV and related engineering units.  
Current URV (Upper Range Value) and the related engineering units are  
displayed on the Online menu. When the URV contains too many characters  
to display on the Online menu, press 5 to access the PV URV menu and  
view the URV and related engineering units.  
1-20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
1
Process  
Variables  
1
2
3
Present variable  
Percent Range  
Analog Output  
Self Test  
1. Test Device  
2. Loop Test  
3. Calibration  
4. D/A Trim  
2
Diagnostics  
and Service  
1. Apply Values  
2. Enter Values  
1. Tag  
2. PV Snsr Unit  
3. Range Values  
4. Device Info.  
5. Xfer Fnctn  
6.PV Damp  
1
2
3
4
5
6
7
8
Model  
3
Basic Setup  
Tag  
Date  
Descriptor  
Message  
PV snsr s/n  
Final Asmbly #  
Revision  
1
2
3
Univ Rev.  
Fld Dev Rev  
Softw Rev  
1. Process Variables  
2. PV Snsr Unit  
3. Sensor Info  
1
Sensors  
1
2
3
PV LSL  
PV USL  
Generic  
PV Min Span  
Online Menu  
1
Device Setup  
1
2
3
4
5
PV Damp  
PV URV  
2
3
4
5
PV  
AO  
LRV  
URV  
PV LRV  
2
Signal  
Condition  
Xfer Fnctn  
PV % Range  
1
A/O 1  
2
3
4
5
A/O Alarm Type  
Loop Test  
1. Analog Output  
D/A Trim  
4
Detailed Setup  
Scaled D/A Trim  
3
Output  
Condition  
1
Poll Address  
2. HART Output  
2 Number of Request  
Preambles  
1
2
3
4
5
6
7
8
Model  
Tag  
Date  
Descriptor  
Message  
PV Snsr S/N  
Final Asmbly Num  
Revision  
4
Device  
Information  
1
2
3
Univ Rev.  
Fld Dev Rev  
Softw Rev  
5
Review  
FIGURE 1-22. Generic Online Menu Tree.  
1-21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
FREQUENCY DEVICE MENU  
YZ /  
3
From the Main menu, press  
to access the Frequency Device menu  
(Figure 1-23). This menu displays the frequency output and corresponding  
pressure output for the current-to-pressure devices. The output shown below  
was taken from device Model 3311.  
FIGURE 1-23. Frequency Device Menu.  
UTILITY MENU  
From the Main menu, press  
J K L  
4
to access the Utility menu (Figure 1-24).  
The Utility menu provides access to functions that affect only the operation of  
the HART Communicator.  
FIGURE 1-24. Utility Menu.  
Configure Communicator Menu  
From the Utility menu, press 1 to access the Configure Communicator menu  
(Figure 1-25). Use this menu to set the polling, adjust the LCD contrast, set  
the Communicator off time, or set the number of ignore diagnostics  
messages.  
FIGURE 1-25. Configure Communicator Menu.  
1-22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Polling Menu  
Use the Polling options to configure your HART Communicator to  
automatically search for all or specific connected devices. The HART  
protocol allows you to communicate with multiple HART devices on a single  
twisted pair of wires over leased telephone lines.  
When several devices are connected in the same loop (multidropped), each  
device must be assigned a unique address. To find the individual device  
addresses, use the Digital Poll option to find each connected device in the  
loop and list them by tag number.  
Communication between the Communicator and multidropped transmitters is  
digital, with the analog output fixed. In a multidrop installation, each  
transmitter is identified by a unique polling address of 0 or 1–15 and  
responds to the commands defined in the HART protocol.  
Use the up and down arrow keys to highlight the desired polling option:  
Press ENTER (F4) to enter the highlighted option and return to the Configure  
Communicator menu. Or, press ESC (F3) to return to the Configure  
Communicator menu without changing the Polling.  
STU  
1
From the Configure Communicator menu (Figure 1-25), press  
access the Polling menu (Figure 1-26).  
to  
FIGURE 1-26. Polling Menu.  
The Polling options are:  
Never Poll connects to a device at address 0, and if not found, will not poll  
for devices at address 1–15.  
Ask Before Polling connects to a device at address 0, and if not found, asks  
if you want to poll for devices at address 1–15.  
Always Poll connects to a device at address 0, and if not found, will  
automatically poll for devices at address 1–15.  
Digital Poll automatically polls for devices at address 1–15, regardless.  
Poll Using Tag asks the user for a tag to use to connect to a device.  
Refer to your device-specific manual for more information on changing a  
device polling address.  
1-23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Contrast Menu  
The Contrast menu adjusts the contrast on the LCD. However, the first time  
you reset and save the contrast, it is entered permanently. When you turn the  
Communicator off, then on, the adjusted setting will reappear. If you need  
help, call your service center for assistance.  
Follow these steps to adjust the contrast:  
VWX  
2
1. From the Configure Communicator menu, press  
to access the Con-  
trast menu (Figure 1-27).  
FIGURE 1-27. Contrast Menu.  
2. Follow the on-screen instructions to adjust the display contrast. Press ESC  
(F3) to return to the Configure Communicator menu without adjusting the  
contrast. To save the changes to the contrast, press ENTER (F4) and the  
Configure Communicator menu displays.  
Off Time Menu  
Off Time is the amount of time that elapses before your HART Communicator  
turns off automatically when not in use. Use the following steps to set the  
automatic turn off option:  
YZ /  
3
1. From the Configure Communicator menu, press  
to access the Off  
Time menu (Figure 1-28).  
FIGURE 1-28. Off Time Menu.  
2. Use the numeric keys to select the automatic turnoff time or press ESC  
(F3) to return to the Configure Communicator menu without adjusting the  
off time.  
1-24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
3. To save the off time change, press ENTER (F4) and the Configure  
Communicator menu displays.  
Entering Zero (0) will disable this option. The maximum time allowed is 255  
minutes. However, be aware that no information will be received about the  
improper operation of a field device when the Communicator is turned off.  
Ignore Diagnostics Menu  
The HART Communicator is designed to display diagnostic messages from a  
connected device. The Ignore diagnostics option allows you to specify the  
number of ignored messages, extending the time between displayed  
messages. This count will default to a nominal count of 50 out of a range of  
50–500 each time the Communicator is turned on (Figure 1-29).  
FIGURE 1-29. Ignore Diagnostics Menu.  
Delete Configs Menu  
The HART Communicator is capable of storing configurations in the Memory  
Module or data pack. You can also add items to the Hotkey menu. The Delete  
Configs menu allows you to delete in one step all configurations saved in the  
module or data pack, as well as to delete all menu items added to the Hotkey  
menu.  
FIGURE 1-30. Delete Configurations Menu.  
1-25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
System Information Menu  
VWX  
2
From the Utility menu, press  
to access the System Information menu  
(Figure 1-31).  
FIGURE 1-31. System Information Menu.  
Motherboard system information consists of the Serial Peripheral Interface  
Time (SPI Time) and the firmware revision number.  
Module system information consists of hardware and software data. For  
example, you can find the hardware revision, RAM size, and Flash size; or,  
the different software revisions and binary sizes.  
data pack system information consists of the EEPROM size and revision  
number.  
Listen for PC Menu  
From the Utility menu, press  
Y Z /  
3
to access the Listen for PC menu (Figure  
1-32).  
FIGURE 1-32. Listen for PC Menu.  
The Listen for PC menu allows you to set up your HART Communicator so it  
can accept data transfer and requests from the PC. On the PC side, you  
must be running Asset Management Solutions (AMS) software. If AMS is  
installed, you can upload and download the device configuration information.  
Accessing data stored in the HART Communicator from the connected PC is  
a convenient way to view, compare, copy, and reconfigure field device  
configurations.  
1-26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Follow these steps to connect your HART Communicator to a PC:  
1. Plug the PC Communication Adapter into the 9-pin Serial Port located on  
the back of the Communicator. Refer to Appendix B for an illustration of  
the PC Communication Adapter and the Communicator.  
2. Plug the PC 25-pin Serial Port cable into the other end of the PC  
Communication Adapter.  
3. Connect the PC’s Serial Port cable to the back of the PC. Depending on  
the PC, you must have either a 9-pin or 25-pin plug on the PC end of the  
cable to connect to the PC.  
4. Set the Communicator to Listen for PC.  
5. Move to the PC keyboard. All communication between the two systems is  
initiated at the PC.  
6. Start the AMS application and select the HART Communicator icon to start  
communication. Table 1-2 describes the main interface options selectable  
by right-clicking the Communicator icon in AMS. Refer to the AMS  
application online help system for details.  
NOTE: AMS must also be configured appropriately to communicate with the  
HART Communicator. See the AMS User’s Guide for details.  
TABLE 1-2. Main Options for the PC AMS Interface.  
Main Option  
Description  
Open and close the con-  
nection to the HART  
Communicator.  
Opens or closes the table of contents located in the  
HART Communicator. This TOC is only a list of the con-  
figurations and includes partial configurations. It does  
not contain the configuration parameters. The configu-  
rations are listed by name, tag, or description and are  
grouped according to location: Memory Module or data  
pack.  
Optimize memory in the  
HART Communicator.  
Compresses the memory in the HART Communicator’s  
Memory Module and data pack. It helps avoid “out of  
memory” conditions when loading device configurations  
into the Communicator.  
View and change HART  
Communicator proper-  
ties.  
Displays a property sheet where you can set the PC-to-  
Communicator operation options or check on  
resources, version number, and available memory.  
Move data between the  
HART Communicator,  
connected devices, and  
the AMS database.  
Allows you to copy, cut, paste, and drag/drop icons as  
well as move device configurations from the HART  
Communicator to a connected device or to another  
area in the database.  
Print device configura-  
tion.  
Allows you print out the device configuration parame-  
ters using the File menu Print command.  
1-27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Storage Location Menu  
From the Utility menu, press 4 to access the Storage Location menu  
(Figure 1-33). The Storage Location menu allows you to access the Memory  
Module or data pack memory permanent storage locations.  
FIGURE 1-33. Storage Location Menu.  
The PC option requires AMS software running in your computer. Refer to  
Listen for PC Menu on page 1-26 for more information.  
When either the Memory Module or data pack storage locations are opened,  
you can use the Label submenu to view or edit the assigned name of the  
label given to the selected storage location. Or, with the Space Usage  
submenu, you can view the total memory and amount of free memory for the  
storage location.  
Simulation Menu  
The HART Communicator provides a simulation mode that allows you to  
simulate an online connection to a HART-compatible device without  
connecting the device. The simulation mode is a training tool that enables  
you to become familiar with different devices before configuring them in a  
critical environment. A simulated configuration cannot be saved, however.  
To simulate an online connection from the Main menu:  
MNO  
5
1. From the Utility menu, press  
to access the Simulation menu. See  
Utility Menu on page 1-22. The Manufacturer menu displays a list of  
manufacturers with device descriptions currently installed in your Commu-  
nicator.  
2. Select a manufacturer. The Model menu displays, containing a list of  
currently installed device models provided by the selected manufacturer.  
3. Select the device you want to simulate. The Fld dev rev menu displays,  
containing the current field device revisions for the selected model.  
1-28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
4. To access the main configuration menu, select the applicable device  
revision. The Online menu for the simulated device is displayed. You can  
now use the HART Communicator as if it were connected to the selected  
device, and perform any online task.  
If you are unsure of the device revision, connect the HART Communicator  
to the device and determine its device revision level. This information is  
most commonly accessed from Online menu>Device Setup>Detailed  
Setup>Device Information. For more information, see your device-specific  
manual.  
SAVING A CONNECTED DEVICE CONFIGURATION  
Selecting the  
option from any Online menu allows you to save a  
SAVE  
configuration transmitted from a connected device to a permanent storage  
location.  
To save, change, and send a stored configuration:  
SAVE  
1. Select  
.
2. Enter a storage location (Memory Module or data pack).  
3. Enter a Name and configuration Data Type. Name defaults to the online  
device Tag, and the Data Type defaults to Standard with all editable  
variables marked.  
NOTE: Saved configurations have to be “Full” for storing in your PC in AMS  
software.  
Warnings appear if there is not enough memory to store the transmitted  
configuration or if there is no list of configurable variables with Data Type  
set to standard.  
SAVE  
The  
key disappears until you change any configuration data.  
4. To change the configuration data, go into the Device Setup menu options  
and change the required data. For example, if the Tag needs to be  
changed, start with the Device Setup menu and go into the Basic Setup  
menu options, open Tag, and change the data.  
ENTER  
SEND  
Press  
to load the changed data, then press  
to send your  
changes to the connected device.  
SAVE  
5. After each data configuration is sent, the  
function key appears. You  
have the option to save the individual variable or continue to change all of  
the variables and save them all at once.  
1-29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
SAVE  
SEND  
key will  
6. If you choose not to  
data but want to continue, the  
reappear after each selection is entered.  
7. Repeat the above process where necessary to modify each device  
configuration.  
When saving a new configuration or changing a saved configuration  
offline, you will not encounter the send key.  
USING THE HOT KEY  
The Hot Key menu is a user-definable menu that can hold up to 20 options of  
your most frequently performed tasks.  
Figure 1-34 shows a typical Hot Key menu with four added options. The first  
option, Range values, is permanent and cannot be changed. It provides  
quick access to review or modify the device range values.  
To use the Hot Key, you must properly connect the HART Communicator to a  
device. You can access the Hot Key menu from any menu, or before  
powering up the Communicator, by simply pressing the Hot Key.  
To use the Hot Key menu:  
1. Connect the HART Communicator to a HART-compatible device.  
2. Press the Hot Key.  
3. Initially, the Hot Key menu displays with only Range values listed. Refer to  
Customizing the Hot Key Menu on page 1-31 for details on how to add  
options. The figure below shows some added options.  
4. Select the desired option from the Hot Key menu.  
FIGURE 1-34. Sample Hot Key Menu.  
5. Follow the online instructions to perform the selected function.  
NOTE: If your HART Communicator does not provide access to the Hot Key  
menu for a particular device, that device does not support Hot Key  
functionality.  
1-30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Customizing the Hot Key Menu  
You can customize the Hot Key menu to provide fast access to  
Range values and your most frequently used tasks. Range values is  
a permanent option providing quick access to rerange. This option cannot be  
deleted from the Hot Key menu.  
Adding Options to the Hot Key Menu  
The Hot Key menu has space for up to 20 online options. For example, if you  
have to change device tags and damping often, you can add these functions  
to the Hot Key menu. The HART Communicator automatically saves them so  
they can be quickly accessed by pressing the Hot Key. If you turn the unit off,  
then later turn it back on using the Hot Key, your customized menu will  
display.  
With the Online menu or any of the submenu options open, use the following  
steps to add customized options to the Hot Key menu:  
1. Using the up or down arrow key, move the menu bar to highlight the option  
you want to add to the Hot Key menu.  
2. Press any one of the three shift keys, release it, and then press the Hot  
Key. This is shown in the following key sequence:  
3. The Hotkey Configuration menu displays (Figure 1-35).  
FIGURE 1-35. Hotkey Configuration Menu.  
The Hotkey Configuration menu displays the new topic you want added to  
the current list of Hot Key options. The figure above indicates that Tag is  
being added to the Hot Key menu in addition to the permanent Range  
values feature. Press ADD (F3) to add the Tag option to the Hot Key  
menu. Press EXIT (F4) to exit the task and display the previous menu.  
1-31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
4. Press ALL(F1) to add the option to the Hot Key menu for all of the HART-  
compatible devices supported in your Communicator; or, press ONE (F4)  
to add the option to the Hot Key menu for the specific device to which you  
are currently connected. See Figure 1-36.  
FIGURE 1-36. Adding a Hot Key Option.  
5. If the message “Mark as read only variable on Hot Key menu?”  
Figure 1-37 displays, press YES (F1) to mark the variable for this option  
as read-only, or press NO (F4) to mark the variable as read/write. For  
example, marking the tag number of a device to be read-only allows you to  
view, but not change, the tag number through the Hot Key menu.  
FIGURE 1-37. Marking a Read-Only Hot Key Option.  
When adding a variable such as tag number, you can choose to display  
the current variable value as part of the menu option. If you choose to  
display the value of the variable in the Hot Key menu, the value appears  
next to the option. Figure 1-38 shows the value of the tag displayed next  
to the tag option on the Hot Key menu.  
FIGURE 1-38. Hot Key Menu.  
1-32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
6. Press YES (F1) to display the variable associated with the option on the  
Hot Key menu, or press NO (F4) to not display it. See Figure 1-39.  
FIGURE 1-39. Variable Display Option.  
7. Press EXIT (F4) on the Hot Key Configuration menu to complete the task.  
The options are now included on the Hot Key menu.  
Deleting Options from the Hot Key Menu  
Use the following steps to delete an online option from the Hot Key menu:  
1. Press any one of the three shift keys, release it, and then press the Hot  
Key. This is shown in the following key sequence:  
2. The Hotkey Configuration menu is displayed (Figure 1-40).  
FIGURE 1-40. Deleting a Hot Key Option.  
Move the menu bar to highlight the option to be deleted and press DEL  
(F2). The menu bar will move to the next menu option. Press DEL (F2) to  
delete the next highlighted option, as desired. The Range values  
functionality cannot be deleted.  
3. When you are through deleting options, press EXIT (F4) to exit the Hotkey  
Configuration menu and return to the menu containing the option you just  
deleted.  
Note: For an easy method to quickly delete all menu items added to the Hot  
Key menu, refer to Delete Configs Menu on page 1-25.  
1-33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
THE HART COMMUNICATOR AND THE YEAR 2000  
The HART Communicator is Year 2000 Compliant if the operating system is  
level 4.6 or greater. To determine the operating system level in your HART  
Communicator, turn it on. The first screen displays the “Module Rev”, which  
is the operating system level. If you need to update your operating system  
software, contact your nearest product representative.  
NOTE: When you power up the Communicator, the Firmware Rev number  
appears first. A few seconds later, the Module Rev number displays one line  
below the Firmware Rev.  
Editing the Date  
When you edit a date, you have three fields to edit: the first field is the month,  
the second field is the day, and the third field is the year.  
If you enter the year using two digits, the HART Communicator will assume  
that the year is 1900 plus the value you enter.  
If you enter four digits, the HART Communicator will use all four digits to  
represent the year. By definition in the HART PROTOCOL, the year must be  
between 1900 and 2155.  
When a date is displayed, the HART Communicator will display two digits in  
the year if the year is between 1900 and 1999. If the year is 2000 or greater,  
the HART Communicator will display all four digits.  
FIGURE 1-41. Date Menu.  
1-34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
SERVICING THE HART COMMUNICATOR  
As shown in Figure 1-42, the modular construction of the HART  
Communicator allows easy disassembly of the battery pack, the Memory  
Module, and the data pack 100. This section discusses how to change  
alkaline batteries, recharge the NiCad battery pack, upgrade the  
Communicator software, and install and remove the data pack 100.  
Replaceable  
(AA)  
or optional  
rechargeable  
(NiCad)  
Memory Module  
battery pack  
data pack 100  
FIGURE 1-42. HART Communicator Exploded View.  
Calibrating the HART Communicator  
It is not necessary or possible to calibrate your HART Communicator. It has  
no measurement circuitry and does not measure analog output from the field  
device. The Communicator is strictly a communication interface that  
communicates digitally with HART-compatible devices. It is not applicable to  
NIST standards, and is not subject to calibration.  
Using a Battery Pack  
The HART Communicator is available with a battery pack that holds five AA  
alkaline cells, or with a rechargeable nickel-cadmium power pack. The  
alkaline cells last approximately 150 hours, and the NiCad cells last  
approximately 60 hours with normal usage. When approximately one hour of  
battery life remains, a low-battery icon appears in the upper right corner of  
the display.  
1-35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Changing Alkaline Batteries  
!
WARNING  
Explosions can result in death or serious injury. Do not remove or  
replace battery pack in an explosive atmosphere.  
Refer to Figure 1-43 and use the following steps to change alkaline  
batteries:  
FIGURE 1-43. Battery Pack Removal.  
1. Completely loosen the three captive screws holding the Communicator  
battery pack.  
2. Grasp the battery pack and pull it away from the Communicator. Make  
sure not to bend the pins connecting the battery pack to the  
Communicator.  
3. Remove and properly dispose of batteries.  
4. Referring to the battery orientation diagram inside the battery pack, insert  
five new AA alkaline batteries.  
5. Carefully align the pins with the Communicator base and replace the  
battery pack.  
6. Tighten the three screws.  
7. Turn on the Communicator to verify operation and ensure the batteries are  
installed properly.  
1-36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Recharging the Battery Pack  
!
WARNING  
Explosions can result in death or serious injury. Do not recharge the NiCad  
battery pack in an explosive atmosphere.  
NiCad battery packs are shipped from the factory discharged. Prior to the  
first use, charge the battery pack while it is disconnected from the  
Communicator. Subsequent charges may be performed while using or  
storing the HART Communicator, without removing the battery pack.  
NOTE: If the HART Communicator is stored for an extended period of time,  
or the battery pack becomes completely discharged, remove the battery  
pack from the Communicator and recharge it separately prior to using.  
To recharge while using the Communicator, plug the recharger into an AC  
outlet or power source. To recharge while storing the Communicator, plug the  
recharger into an AC outlet or power source, make sure the HART  
Communicator is off, and charge for 16 hours. Overcharging will not harm  
the Communicator battery pack.  
NOTE: For optimum performance, periodically discharge (use battery power  
until the low battery icon appears) and then fully recharge the battery pack.  
Using a Memory Module  
The HART Communicator is supplied with a replaceable Memory Module  
(Figure 1-44). A 12 MB Memory Module is the recommended standard.  
The Memory Module is programmed to communicate with specific HART-  
compatible devices. Refer to Reviewing Installed Devices on page 1-12 to  
find the specific HART-compatible devices that are programmed into your  
Communicator’s Memory Module.  
If you find that some specific devices are not listed in your Memory Module,  
contact your nearest service representative. Your Memory Module may be  
reprogrammed or replaced to include support for the required HART devices.  
1-37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Replacing the Memory Module  
!
WARNING  
Explosions can result in death or serious injury. Do not remove or replace  
battery pack in an explosive atmosphere.  
Refer to Figure 1-43 and Figure 1-44, and use the following steps to replace  
the Memory Module:  
FIGURE 1-44. Memory Module Replacement.  
1. Completely loosen the three captive screws holding the Communicator  
battery pack.  
2. Grasp the battery pack and pull it straight up from the Communicator. Do  
not bend the battery pack’s connecting pins during the process.  
3. Loosen the two captive screws holding the Memory Module.  
4. Grasp the Memory Module and pull it away from the Communicator.  
5. Align the new Memory Module with the Communicator, tighten the two  
screws, and replace the battery pack.  
1-38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Installing and Removing the Data Pack 100  
Refer to Figure 1-43, Figure 1-44, and Figure 1-45.  
Use the following steps to install or remove the data pack:  
FIGURE 1-45. Data Pack 100 Installation and Removal.  
To Install the data pack:  
1. Remove the battery pack from the Communicator. Next, either remove the  
Memory Module or leave it assembled to the Communicator.  
2.The data pack is keyed to prevent incorrect installation. When the  
Communicator is facing down, insert the data pack with the part number  
label facing down; the hinge of the handle will be on the left. Press firmly in  
place with your fingers.  
To remove the data pack:  
1. Insert the flat edge of a small screwdriver under the outside edge of the  
handle. Lift the handle to disconnect the data pack from its connector.  
2. Raise the handle and pull the data pack out of the Memory Module.  
1-39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
1-40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION 2  
Common Tasks for Fisher-Rosemount HART  
Devices  
INTRODUCTION  
This section displays HART Communicator menus and describes tasks  
common to Fisher-Rosemount HART products.  
POWERING UP ONLINE  
Powering up online provides direct access to the Online menu. This menu  
provides critical data that is continuously updated. To be powered online, the  
Communicator must be connected to a 4–20 mA loop.  
To power up the Communicator and access a HART compatible device:  
1. Be sure the Communicator is connected to a HART compatible device.  
See HART Communicator Connections on page 1-2 for information  
about proper connections.  
2. Power the Communicator by pressing the On/Off key.  
NOTE: If a device is found, the HART Communicator displays the Online  
menu. If no device is found, the Communicator displays the Main menu. If no  
device is found, check the connections, verify the presence of the 250 ohms  
load resistance in series in the loop, and retry by selecting ‘Online.’ To poll  
multiple devices in the loop, refer to Polling Menu on page 1-23. For help  
on communication problems, see Appendix D.  
2-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
ONLINE MENU  
The Online menu is the first menu to appear when the Communicator is  
connected to a HART compatible device. This menu is structured to provide  
important information about the connected device immediately on powering  
up the Communicator (Figure 2-1). This menu displays critical, up-to-date  
device information including primary variable, analog output, lower range  
value, and upper range value.  
5ø  
12 ø  
FIGURE 2-1. Online Menu.  
Because of the important information provided in the Online menu, some  
other menus provide instant access to it. When access is available, the  
HOME label appears above the F3 key. Press HOME (F3) to return to the  
Online menu. For more information about the Home key, refer to Section 1.  
Move through the menu using  
and  
and press  
to select an  
option, or simply press the corresponding numerical key. The Online menu  
options are described as follows.  
Device Setup  
STU  
1
Press  
to access the Device Setup menu from the Online menu.  
The Device Setup menu accesses every configurable parameter of the  
connected device. Refer to the Device Setup Menu on page 2-4 for more  
information.  
2-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Primary Variable (PV)  
VWX  
2
Press  
to access Primary Variable.  
The Online menu displays critical process information that is continuously  
updated. If the PV and related engineering units are too long, they will not  
appear on the Online menu. Select PV to view primary variable and the  
related engineering units.  
Analog Output (AO)  
YZ /  
3
Press  
to access Analog Output.  
The analog output is the signal on the 4–20 mA scale that corresponds to the  
primary variable. When the AO contains too many characters to display on  
the Online menu, select AO to view the analog output and related  
engineering units.  
Lower Range Value (LRV)  
J K L  
4
Press  
to access Lower Range Value.  
Select LRV to view the lower range value and related engineering units.  
Upper Range Value (URV)  
MNO  
5
Press  
to access Upper Range Value.  
Select URV to view the upper range value and related engineering units.  
2-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
DEVICE SETUP MENU  
As shown in Figure 2-2, the Device Setup menu contains the following five  
options:  
STU  
1
Press  
to access the Device Setup menu from the Online menu. The  
options on this menu (Figure 2-2) are described in the following paragraphs.  
FIGURE 2-2. Device Setup Menu.  
Process Variables  
STU  
Press  
1
to access the Process Variables menu.  
This menu lists all process variables and their values. These process  
variables are continuously updated.  
Diag/Service  
VWX  
2
Press  
to access the Diag/Service menu.  
This menu offers device and loop tests as well as calibration options. Figure  
2-3 illustrates a typical menu.  
FIGURE 2-3. Diagnostics and Service Menu.  
Test device initiates a diagnostic routine at the device and can report an  
electronics failure, as well as other failures that can affect performance.  
2-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Loop test can fix the transmitter output at a specified analog value, and can  
be used to test the integrity of the loop and the operation of indicators,  
recorders, or similar devices in the loop.  
Calibration can include such operations as configuring output related  
parameters, performing a sensor trim, or performing an analog output trim.  
Basic Setup  
YZ /  
3
Press  
to access the Basic Setup menu.  
This menu provides quick access to a number of configurable parameters  
including tag, unit, range values, and damping. Figure 2-4 illustrates a  
typical Basic setup menu.  
FIGURE 2-4. Basic Setup Menu.  
The tag number identifies a specific device. Changing units affects the  
engineering units that are displayed. Reranging changes the analog output  
scaling. Changing damping affects the response time of the transmitter to  
smooth the output when there are rapid input variations.  
The options available in the Basic Setup menu are the most fundamental  
tasks that can be simply performed with a given device. These tasks are a  
subset of the options available under the Detailed Setup menu.  
Detailed Setup  
J K L  
4
Press  
to access the Detailed setup menu.  
This menu provides access to every editable device parameter and all  
device functions. The Detailed Setup menu varies widely from one HART  
compatible device to another. Functions in this menu can include tasks such  
as characterization, configuration, and sensor and output trims.  
2-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Review  
MNO  
Press  
5
to access the Review menu.  
This menu lists all of the parameters stored in the connected device,  
including information about the measuring element, signal condition, and  
output. It also includes stored information about the connected device such  
as tag, materials of construction, and device software revision.  
FAST KEY SEQUENCES  
A fast key sequence is simply a sequence of numerical button presses,  
corresponding to the menu options that lead you to a given task. For  
example, Figure 2-5 displays the fast key sequence for trimming analog  
output on a Model 1151 Pressure Transmitter.  
1
2
3
2
FIGURE 2-5. Sample Fast Key Sequence.  
The first digit represents option number one on the Online menu. Once this  
option is selected, the Device Setup menu appears. The second digit  
represents option number two of the Device Setup menu, which is the  
Diagnostics and Service menu. The Calibration menu is activated by  
pressing the third digit, and the fourth digit accesses the trim analog output  
option of the Calibration menu. This example is illustrated for the Model 1151  
Pressure Transmitter on page 2-7. For more detailed information on fast key  
sequences, consult your product manual.  
2-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Trimming the analog output is a calibration of the output circuitry, by setting  
the 4 and 20 mA points. Once the 4 and 20 mA points are set, all  
intermediate values are automatically adjusted. See Menu Trees in Section  
3 for a corresponding menu tree.  
From the Online menu, select Device setup.  
50  
12 0  
From the Device setup menu, select Diag/  
Service.  
From the Diag/Service menu, select  
Calibration.  
From the Calibration menu, select Trim  
analog output.  
From the Trim Analog Output menu, select  
the desired option and follow the on-line  
instructions.  
2-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION 3  
Menu Trees  
INTRODUCTION  
This section displays typical examples of menu trees for specific Fisher-  
Rosemount products.  
Menu trees show the primary commands and options available when using a  
sequence of menu selections. Text displayed in all bold capital letters in the  
menu trees indicates a progression to the next level. Due to space  
limitations, all levels may not be shown. Also note that your specific device  
could be different from the example shown. Consult your product manual for  
more detailed information.  
The menu trees are identified by product and model number at the top of the  
page and are arranged in numeric-alpha order.  
3-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 54pH/ORP Transmitter  
1 pH  
1 VIEW FLD DEV  
VARS  
2 ORP  
3 Temp  
4 Input  
5 glass  
6 Ref  
1 PROCESS  
VARIABLES  
1 PV is  
2 pH  
3 pH & rnge  
4 AO  
2 VIEW PV-ANALOG 1  
3 VIEW SV-ANALOG 2  
1 SV is  
2 pH  
3 pH & rnge  
4 AO  
5 Convention  
1 Standardize pH  
2 Standardize ORP  
3 pH  
4 ORP  
5 0 offset  
6 0 offset  
7 Slope  
8 Buffer calibration  
9 Buffer calibration  
4 View alarms  
5 View status  
5 Convention  
1 View status  
2 View alarms  
3 Master reset  
1 TEST DEVICE  
2 Fix analog output  
3 CALIBRATION  
2 DIAG/  
SERVICE  
1 CALIBRATE PV  
2 ADJUST  
TEMPERATURE  
4 Trim analog output  
5 Hold mode  
1 Begin procedure  
2 Temp  
3 Temp comp  
4 Man. temp  
1 pH LRV  
2 pH URV  
3 pH  
4 pH % rnge  
5 pH xfer fun  
1 Tag  
2 PV RANGE VALUES  
3 BASIC  
SETUP  
1 pH LRV  
2 pH URV  
3 pH  
4 pH % rnge  
5 pH xfer fun  
3 SV RANGE VALUES  
4 ALARM SETPOINTS  
1 Spt  
2 Spt  
3 Spt  
4 Timer  
5 pH  
1 PV is  
2 Imped comp  
3 Convention  
4 Autocal  
5 SST  
1 Tag  
2 Descriptor  
3 Message  
4 Snsr text  
5 Date  
6 ORP  
6 SSS  
5 DEVICE  
INFORMATION  
7 Oper iso  
8 Snsr iso  
9 TC  
1 SENSORS  
1 MAIN SENSOR  
2 TEMPERATURE  
1 Temp snsr  
2 Temp comp  
3 Man. temp  
2 SIGNAL CONDITION  
1 PV RANGE VALUES  
2 SV RANGE VALUES  
3 ALARM 1  
4 ALARM 2  
5 ALARM 3  
4 DETAILED  
SETUP  
1 ANALOG OUTPUT  
2 Relay deflt  
3 Fix analog output  
4 Trim analog output  
5 HART OUTPUT  
3 OUTPUT CONDTION  
4 DEVICE INFORMATION  
5 DIAGNOSTICS  
6 Type  
1 Diagnostics  
2 GFH  
3 GFL  
4 RFH  
5 0 limit  
6 Cal warn  
1 SENSORS  
2 OUTPUTS  
3 ALARM RELAYS  
4 DIAGNOSTICS  
5 DEVICE  
6 LOCAL DISPLAY  
5 REVIEW  
INFORMATION  
6 LOCAL DISPLAY  
3-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 333 HART® Tri-Loop Converter  
1 Status group 1  
1 STATUS  
2 Status group 2  
1 TEST DEVICE  
2 Loop test  
2 Reset  
1 DIAG/  
SERVICE  
1 CONFIGURE CH1  
2 CONFIGURE CH2  
3 CONFIGURE CH3  
1 CONFIGURE  
CHANNELS  
3 CALIBRATION  
4 D/A trim  
2 Recall fact trim  
1 CH1 Burst Variable  
2 CH1 Units  
1 Tag  
3 CH1 Lower Range  
4 CH1 Upper Range  
5 CH1 Enabled  
1 CONFIGURE CH1  
2 CONFIGURE CH2  
3 CONFIGURE CH3  
1 CH2 Burst Variable  
2 CH2 Units  
3 CH2 Lower Range  
4 CH2 Upper Range  
5 CH2 Enabled  
2 CONFIGURE  
CHANNELS  
2 BASIC  
SETUP  
1 CH3 Burst Variable  
2 CH3 Units  
3 CH3 Lower Range  
4 CH3 Upper Range  
5 CH3 Enabled  
1 DEVICE SETUP  
1 Model  
2 Dev id  
3 Tag  
4 Date  
3 DEVICE  
5 Descriptor  
6 Message  
7 Final asmbly  
num  
INFORMATION  
1 Universal rev  
2 Fld dev rev  
3 Software rev  
8 REVISION #'S  
1 Loop test  
2 D/A trim  
3 Scaled D/A trim  
1 ANALOG  
OUTPUT  
1 OUTPUT  
CONDITION  
1 Poll addr  
2 Num req preams  
3 Num resp preams  
3 DETAILED  
SETUP  
2 HART  
OUTPUT  
1 Model  
2 Dev id  
3 Tag  
2 DEVICE  
INFORMATION  
4 Date  
5 Descriptor  
6 Message  
7 Final asmbly  
num  
4 REVIEW  
1 Universal rev  
2 Fld dev rev  
3 Software rev  
8 REVISION #'S  
3-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 644 Temperature Transmitter  
1
2
3
4
5
Snsr 1  
Snsr 1 % Rnge  
Snsr 1 A/O Output  
Term Temp  
1
PROCESS  
VARIABLES  
1
2
PV  
SV  
VARIABLE MAPPING  
1
2
3
4 ma  
20 ma  
Exit  
1
2
3
Status  
1
TEST DEVICE  
Self Test  
Master Test  
1
2
3
4
4 ma  
20 ma  
Other  
End  
2
3
4
LOOP TEST  
1
2
3
4
5
PV LRV  
2
DIAGNOSTIC  
AND  
PV URV  
PV Eng Units  
Lower Snsr Lmts  
Upper Snsr Lmt  
SERVICE  
1
2
3
4
5
APPLLY VALUES  
RANGE VALUES  
SNRS TRIM  
D/A Trim  
Scaled D/A Trim  
CALIBRATION  
Smart Calibration  
1
2
3
OHM/MV Trim  
SENOR REF  
RE-ENABLE  
TRIM  
1
Differential Temp  
Terminal Temp  
Sensor 1  
1
2
3
4
5
6
Tag  
PV Unit  
2
3
4
1
2
3
Factory Trim  
Sensor 1 Trim  
Sensor Ref  
RANGE VALUES  
CONNECTIONS  
PV Damp  
Sensor 2  
3
BASIC SETUP  
1
Select Sensor  
1
PV Units  
1
# of Wires  
Sensor 1 Snsr s/n  
1
PV Snsr 1  
2
3
4
5
PV Unit  
SENSOR SETUP  
SENSOR INFO  
SENSOR TRIM  
1
2
3
PROCESS  
SENSOR  
1
Term Temperature  
Unit  
TERM TEMP  
SENSOR  
2
3
4
Damping  
1
SENSORS  
Term Temp Limits  
A/D CONVR  
INFO  
1
50/60 Hz filter  
1
2
3
4
5
LRV  
URV  
Snsr % Rnge  
Snsr Damp  
Xfr Funt  
1
2
3
4
5
DEVICE SETUP  
PV  
2
3
SIGNAL  
1
A/O Output  
1
2
3
4
4 ma  
CONDITION  
2
3
4
5
A/O Alrm Type  
4
DETAILED  
SETUP  
20 ma  
Other  
End  
PV AO  
LOOP TEST  
D/A Trim  
Scaled D/A  
Trim  
PV LRV  
PV URV  
1
ANALOG  
OUTPUT  
OUTPUT  
CONDITION  
1
2
3
4
Poll Address  
# Reqst Preams  
Burst Mode  
2
HART  
OUTPUT  
Burst Options  
1
2
3
4
5
6
7
8
9
Snsr Type  
Snsr Connect  
Snsr 1 s/n  
50/60 Hz Filter  
Final Assembly  
Tag  
4
DEVICE INFO  
Descriptor  
message  
1
2
3
Unit Rev  
Fld Dev Rev  
Software rev  
5
REVIEW  
Date,  
Model...etc.  
3-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 1151 Pressure Transmitter  
1
2
3
Pressure  
Percent Range  
Analog Output  
1
2
PROCESS  
VARIABLES  
1
2
3
TEST DEVICE  
Loop Test  
1
2
Self test  
Status  
1
2
Keypad Input  
Apply Values  
DIAGNOSTICS  
AND SERVICE  
1
RERANGE  
1
2
Digital-to-Analog Trim  
Scaled D/A Trim  
2 TRIM ANALOG  
OUTPUT  
CALIBRATION  
1
2
3
4
Zero Trim  
Lower Sensor Trim  
Upper Sensor Trim  
Sensor Trim Points  
3
SENSOR TRIM  
1
2
3
Tag  
Unit  
1
2
Keypad Input  
Apply Values  
RANGE  
VALUES  
3
BASIC SETUP  
4
5
6
DEVICE INFO  
Transfer Function  
Damp  
1
2
3
4
5
Date  
Descriptor  
Message  
Write Protect  
Meter Type  
1
Pressure  
1
2
3
1
2
PROCESS  
2
Percent Range  
VARIABLES  
1
2
3
4
Zero Trim  
1
SENSORS  
Lwr Snsr Trim  
Upr Snsr Trim  
Trim Points  
SENSOR  
SERVICE  
1
2
SENSOR TRIM  
Characterize  
Unit  
1
DEVICE  
SETUP  
PV  
2
3
4
5
PROCESS  
VARIABLES  
1
2
Pressure  
Percent Range  
AO  
LRV  
URV  
2
SIGNAL  
CONDITION  
RANGE  
VALUES  
Unit  
Transfer Function  
Damp  
1
2
Keypad Input  
Apply Values  
3
4
5
1
PROCESS  
VARIABLES  
1
2
3
Pressure  
Percent Range  
Analog Output  
4
DETAILED  
SETUP  
1
2
3
Loop Test  
Digital-to-Analog Trim  
Scaled D/A Trim  
2
ANALOG  
OUTPUT  
3
OUTPUT  
CONDITION  
3
Analog Output  
Alarm  
1
2
3
4
Poll Address  
Number of Request Preambles  
Burst Mode  
4
HART OUTPUT  
Burst Option  
1
2
3
4
Field Device Info  
Sensor Info  
Meter Type  
Self Test  
4
DEVICE  
INFORMATION  
5
REVIEW  
3-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 2081C Conductivity Transmitter  
1
2
3
C
1
PROCESS  
VARIABLE  
1
VIEW FIELD  
DEVICE  
VARIABLES  
Temperature  
AC  
1
PV is  
2
VIEW PV-  
ANAOLOG 1  
2
3
4
PV  
PV % Range  
PV A/O  
3
View Status  
1
2
3
4
Begin Procedure  
C
Cell Const  
Cell Factor  
1
2
STANDARDIZE COND  
1
2
3
View Status  
Loop Test  
1
Cell Const.  
INITIAL SETUP  
2
DIAGNOS  
AND  
SERVICE  
2
Sensor Zero  
3
TEMP SLOPE CAL  
CALIBRATION  
3
ADJUST TEMPERATURE  
1
Begin Procedure  
Temp  
Temp Comp  
Man. Temp  
2
3
4
4
Trim Analog Output  
1
2
3
4
5
6
PV LRV  
PV URV  
PV Damp  
PV pH  
1
2
3
Tag  
1
2
3
4
5
Tag  
PV % Range  
Xfer Fun  
3
BASIC  
SETUP  
PV RANGE VALUES  
Descriptor  
Message  
Snsr Text  
Date  
DEVICE INFORMATION  
1
2
Temp Comp  
Man. Comp  
1
SENSOR  
1
pH LRV  
2
3
4
5
6
pH URV  
pH Damp  
pH  
2
3
SIGNAL  
CONDITION  
pH % Range  
pH xfer fun  
1
2
3
PV A/O  
Loop Test  
1
ANALOG OUTPUT  
HART OUTPUT  
Trim Analog Output  
4
DETAILED  
SETUP  
OUTPUT  
CONDITION  
2
1
Poll Address  
Temp Unit  
Burst Option  
Burst Mode  
2
3
4
1
2
3
4
5
6
7
8
9
Tag  
Descriptor  
Message  
Date  
Snsr Text  
Burst Mode  
Burst Option  
Num Req Preams  
Write Protect  
4
DEVICE INFO  
10 Distributor  
11 Manufacturer  
12 Model  
13 etc.  
1
2
3
SENSORS  
OUTPUTS  
5
REVIEW  
DEVICE INFORM  
3-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 2081pH Transmitter  
1
2
3
pH  
1
PROCESS  
VARIABLE  
1
VIEW FIELD  
DEVICE  
VARIABLES  
Temperature  
Input  
1
2
3
4
PV is  
PV pH  
2
VIEW PV-  
ANAOLOG 1  
PV % Range  
PV A/O  
3
View Status  
1
2
View Status  
1
2
3
4
TEST/STATUS  
Loop Test  
Master Reset  
1
2
3
Begin Procedure  
Slope  
pH  
2
DIAGNOS  
AND  
SERVICE  
1
BUFFER CALIBRATION  
STANDARDIZE ph  
1
2
Begin Procedure  
pH  
2
3
CALIBRATION  
Trim Analog Output  
ADJUST TEMPERATURE  
1
2
3
4
Begin Procedure  
Temp  
Temp Comp  
Man. Temp  
1
2
3
4
5
6
PV LRV  
PV URV  
PV Damp  
PV pH  
1
2
3
Tag  
1
2
3
4
5
Tag  
PV % Range  
Xfer Fun  
3
BASIC  
SETUP  
PV RANGE VALUES  
Descriptor  
Message  
Snsr Text  
Date  
DEVICE INFORMATION  
1
2
Temp Comp  
Man. Comp  
1
SENSOR  
1
pH LRV  
2
3
4
5
6
pH URV  
pH Damp  
pH  
2
3
SIGNAL  
CONDITION  
pH % Range  
pH xfer fun  
1
2
3
PV A/O  
Loop Test  
1
ANALOG OUTPUT  
HART OUTPUT  
Trim Analog Output  
4
DETAILED  
SETUP  
OUTPUT  
CONDITION  
2
1
Poll Address  
Temp Unit  
Burst Option  
Burst Mode  
2
3
4
1
Tag  
2
3
4
5
6
7
8
9
Descriptor  
Message  
Date  
Snsr Text  
Burst Mode  
Burst Option  
Num Req Preams  
Write Protect  
4
DEVICE INFO  
10 Distributor  
11 Manufacturer  
12 Model  
13 etc.  
5
REVIEW  
3-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 2088 Pressure Transmitter  
1 Pres  
2 % rnge  
3 AO  
1 PROCESS  
VARIABLES  
1 Self test  
2 STATUS  
1 TEST DEVICE  
2 Loop test  
3 CALIBRATION  
1 Keypad input  
2 Apply values  
2 DIAG/SERVICE  
1 RE-RANGE  
2 ANALOG  
OUTPUT TRIM  
1 D/A trim  
2 Scaled D/A trim  
1 Tag  
3 SENSOR TRIM  
2 Unit  
1 Zero trim  
2 Lower sensor trim  
3 Upper sensor trim  
4 Snsr trim cal typ  
5 SENSOR TRIM  
POINTS  
1 Keypad input  
2 Apply values  
3 RANGE VALUES  
4 DEVICE  
INFORMATION  
3 BASIC SETUP  
1 Date  
2 Descriptor  
3 Message  
4 Write protect  
5 Damping  
1 Sel dec pt pos  
2 CM Upper Value  
3 CM Lower value  
4 CM Units  
6 METER  
OPTIONS  
1 Meter type  
2 CM SETUP  
1 SENSORS  
1 PRESSURE  
SENSOR  
1 PROCESS  
VARIABLES  
2 SENSOR TRIM  
3 Unit  
1 DEVICE SETUP  
2 PV  
3 AO  
1 PROCESS  
VARIABLES  
2 RANGE  
VALUES  
2 SIGNAL  
CONDTION  
4 LRV  
5 URV  
3 Unit  
4 Damping  
1 PROCESS  
VARIABLES  
1 Pres  
2 % rnge  
3 AO  
4 DETAILED  
SETUP  
3 OUTPUT  
CONDITION  
1 Loop test  
2 D/A trim  
3 Scaled D/A trim  
4 AO Alrm typ  
2 ANALOG  
OUTPUT  
1 Poll addr  
2 Num req preams  
3 Burst mode  
4 Burst option  
3 HART OUTPUT  
1 Meter type  
2 CM SETUP  
3 CMV  
4 METER  
OPTIONS  
1 FIELD DEVICE  
INFO  
4 DEVICE  
INFORMATION  
1 Meas typ  
2 SENSOR  
2 Isoltr matl  
INFORMATION  
3 Fill fluid  
4 Process Connector  
5 Process Conn Matl  
5 REVIEW  
3 Self test  
4 DIAPHRAM  
SEAL INFO  
3-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 2090 Pressure Transmitter  
1 Pres  
2 % rnge  
3 AO  
1 PROCESS  
VARIABLES  
1 Self test  
2 STATUS  
1 Keypad input  
2 Apply values  
1 TEST DEVICE  
2 Loop test  
1 RE-RANGE  
2 DIAG/SERVICE  
3 CALIBRATION  
1 D/A trim  
2 ANALOG  
2 Scaled D/A trim  
OUTPUT TRIM  
1 Zero trim  
3 SENSOR TRIM  
2 Lower sensor trim  
3 Upper sensor trim  
4 Snsr trim cal typ  
5 SENSOR TRIM  
POINTS  
1 Tag  
2 Unit  
3 RANGE VALUES  
1 Keypad input  
2 Apply values  
3 BASIC SETUP  
4 DEVICE  
1 Date  
INFORMATION  
2 Descriptor  
3 Message  
4 Write protect  
5 Damping  
1 Sel dec pt pos  
2 CM Upper Value  
3 CM Lower Value  
4 CM Units  
6 METER  
OPTIONS  
1 Meter type  
3 CM SETUP  
1 PROCESS  
VARIABLES  
2 SENSOR TRIM  
3 Unit  
1 SENSORS  
1 PRESSURE  
SENSOR  
4 DETAILED  
SETUP  
1 DEVICE SETUP  
2 PV  
3 AO  
4 LRV  
5 URV  
1 PROCESS  
VARIABLES  
1 Pres  
2 % rnge  
2 SIGNAL  
CONDITION  
2 RANGE  
VALUES  
1 Keypad input  
2 Apply values  
3 Unit  
4 Damping  
1 Pres  
2 % rnge  
3 AO  
1 PROCESS  
VARIABLES  
3 OUTPUT  
CONDITION  
1 Loop test  
2 ANALOG  
OUTPUT  
2 D/A trim  
3 Scaled D/A trim  
4 AO Alrm typ  
3 HART OUTPUT  
1 Meter type  
2 CM SETUP  
3 CMV  
4 METER  
OPTIONS  
1 FIELD DEVICE INFO  
2 SENSOR INFORMATION  
3 Self test  
4 DEVICE  
INFORMATION  
5 REVIEW  
4 DIAPHRAM SEAL INFO  
3-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 3001S Hydrostatic Transmitter  
1
PROCESS  
VARIABLES  
1
2
3
4
Pres  
% rnge  
A/O  
Snsr temp  
1
Self Test  
1
TEST DEVICE  
Loop Test  
2
Status  
1
2
Keypad Input  
Apply Values  
2
1
2
RE-RANGE  
2
DIAGNOSTICS  
AND SERVICE  
3
CALIBRATION  
TRIM ANALOG  
OUTPUT  
1
2
D/A Trim  
Scaled D/A Trim  
3
SENSOR TRIM  
1
2
3
4
Zero Trim  
Lower Snsr Trim  
Upper Snsr Trim  
Sensor Trim Points  
1
Tag  
1
Date  
2
3
4
5
6
PV Unit  
2
3
4
5
Descriptor  
Message  
Write Protect  
Meter Type  
Range Values  
DEVICE INFO  
Trans Funct  
Damping  
3
BASIC SETUP  
1
2
3
Pres  
% rnge  
Snsr temp  
1
2
PV  
1 PRESSURE  
SENSOR  
1
SENSORS  
SENSOR  
SERV  
1
Sensor Trim  
3
UNIT  
2
TEMP  
SENSOR  
1
2
Sensor Temp  
Snsr Temp Unt  
1
2
3
Pres  
% rnge  
Snsr temp  
1
2
3
4
5
PV  
Range Values  
Unit  
2
3
SIGNAL  
1
2
Keypad Input  
Apply Values  
CONDITION  
Transfer Funtion  
Damping  
1
2
3
4
5
DEVICE SETUP  
PV  
4
DETAILED  
SETUP  
PV AO  
1
2
3
Pres  
PV LRV  
PV URV  
1
2
PV  
% rnge  
Snsr temp  
OUTPUT  
CONDITION  
ANALOG  
OPUTPUT  
1
2
3
Loop Test  
D/A Trim  
Scaled D/A Trim  
3
4
A/O Alrm  
Trim  
1
Poll Address  
Num Req Preams  
Burst Mode  
2
3
4
HART  
OUTPUT  
Burst Option  
4
DEVICE INFO  
1
2
3
4
Field Device Information  
Sensor Information  
Meter Type  
5
REVIEW  
Self Test  
3-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 3044C Temperature Transmitter  
1
2
3
4
5
Sensor 1  
1
PROCESS  
VARIABLES  
Sensor 1 Percent Range  
Sensor 1 Analog Output  
Electronics Temperature  
Variable Mapping  
1
2
3
Status  
1
2
3
TEST DEVICE  
Loop Test  
Self Test  
Master Test  
2
DIAGNOSTICS  
AND SERVICE  
1
2
3
4
5
Apply Values  
Range Values  
1
2
Sensor Input Trim  
Sensor Trim-Factory  
SENSOR TRIM  
Digital-to-Analog Trim  
Scaled D/A Trim  
CALIBRATION  
1
2
3
4
5
6
Tag  
PV Unit  
Range Values  
Connections  
PV Damp  
3
BASIC SETUP  
Sensor 1 Sensor s/n  
1
2
3
Sensor 1  
Snsr 1 Unit  
1
2
Connections  
Snsr 1 snsr s/n  
1
PROCESS  
SENSOR  
SENSOR  
SETUP  
4
Sensor Info  
1
SENSORS  
1
2
Snsr Input Trim  
Snsr Trim-Factory  
5
SENSOR  
TRIM  
1
DEVICE  
SETUP  
PV  
PV AO  
PV LRV  
PV URV  
2
3
4
5
1
2
3
Electronics Temperature  
Unit  
Electronics Temperature Limits  
2
ELECT TEMP  
SENSOR  
1
2
Sensor 1 LRV  
Sensor 1 URV  
Sensor 1 Percent Range  
Sensor 1 Damp  
Transfer Function  
2
SIGNAL  
CONDITION  
3
4
5
4
DETAILED  
SETUP  
1
2
3
4
5
Analog Output  
A/O Alarm Type  
Loop Test  
Digital-to-Analog Trim  
Scaled D/A Trim  
1
ANALOG  
OUTPUT  
3
4
OUTPUT  
2
1
2
3
4
Poll Address  
HART  
CONDITION  
Number of Request Preambles  
Burst Mode  
OUTPUT  
Burst Option  
3
Meter Type  
DEVICE  
INFORMATION  
5
REVIEW  
3-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 3051 Pressure Transmitter  
1 Pres  
2 % rnge  
3 AO  
1 PROCESS  
VARIABLES  
4 Snsr temp  
1 Self test  
2 STATUS  
1 TEST DEVICE  
1 Keypad input  
2 Apply values  
1 RE-RANGE  
2 DIAG/  
SERVICE  
2 Loop Test  
1 D/A trim  
2 Scaled D/A trim  
2 ANALOG  
OUTPUT TRIM  
3 CALIBRATION  
1 Zero trim  
1 Tag  
2 Unit  
3 SENSOR TRIM  
4 Recall fact trim  
2 Lower sensor trim  
3 Upper sensor trim  
4 Snsr trim cal typ  
5 SENSOR TRIM  
POINTS  
3 RANGE  
VALUES  
1 Keypad input  
2 Apply values  
3 BASIC  
SETUP  
4 DEVICE  
INFORMATION  
1 Date  
2 Descriptor  
3 Message  
4 Write protect  
5 Transfer  
function  
1 Sel dec pt pos  
2 CM Upper Value  
3 CM Lower Value  
4 CM Units  
6 Damping  
1 Meter type  
2 CM SETUP  
7 METER  
OPTIONS  
5 CM xf fnct  
1 PROCESS VARIABLES  
2 SENSOR SERVICE  
3 Unit  
1 PRESSURE  
SENSOR  
1 SENSORS  
1 DEVICE  
SETUP  
2 PV  
2 TEMPERATURE  
SENSOR  
1 Snsr temp  
2 Snsr temp unit  
4 DETAILED  
SETUP  
3 AO  
4 LRV  
5 URV  
1 PROCESS  
VARIABLES  
1 Press  
2 % rnge  
3 Snsr temp  
2 SIGNAL  
CONDITION  
1 Keypad input  
2 Apply values  
2 RANGE VALUES  
3 Unit  
4 Transfer function  
5 Damping  
6 Snsr temp unit  
1 High Alarm  
2 Low Alarm  
3 High Sat  
4 Low Sat  
5 AO Alrm typ  
6 Alarm/Sat Type  
7 ALARM/SAT  
LEVELS  
1 PROCESS  
VARIABLES  
3 OUTPUT  
CONDITION  
2 ANALOG  
OUTPUT  
1 FIELD DEVICE INFO  
5 REVIEW  
3 HART OUTPUT  
2 SENSOR  
INFORMATION  
4 METER OPTIONS  
3 Self test  
4 DEVICE  
INFORMATION  
4 DIAPHRAM SEAL  
INFO  
3-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 3051C Pressure Transmitter (Original)  
1
2
3
4
Pressure  
1
PROCESS  
VAR  
Percent Range  
Analog Output  
Sensor Temperature  
1
2
Self test  
Status  
1
2
3
TEST DEVICE  
1
2
RERANGE  
1
Keypad  
Input  
Apply Values  
2
2
DIAGNOS  
AND  
SERVICE  
Loop Test  
1
Digital-to-  
Analog Trim  
Scaled D/A Trim  
TRIM  
ANALOG  
OUTPUT  
2
1
2
3
4
Zero Trim  
CALIBRATION  
Lower Sensor Trim  
Upper Sensor Trim  
Sensor Trim Points  
3
SENSOR  
TRIM  
1
2
3
Tag  
Unit  
1
2
Keypad Input  
Apply Values  
RANGE  
VALUES  
3
BASIC  
SETUP  
1
2
3
Pressure  
% Range  
Snsr temp  
1
2
3
PROCESS  
1
Date  
4
DEVICE INFO  
VARIABLES  
2
3
4
5
Descriptor  
Message  
Write Protect  
Meter Type  
1 DEVICE  
SETUP  
5
Transfer  
Function  
SENSOR  
SERVICE  
1
SNSR  
TRIM  
1
Zero  
Trim  
2
3
4
5
PV  
AO  
2 Lwr Snsr  
Trim  
3 Upr Snsr  
Trim  
4
6
Damp  
Unit  
LRV  
URV  
1
PRESSURE  
SNSR  
TEMP. SENSOR  
1
SENSORS  
2
6
1
2
1
2
3
Snsr Temp  
Snsr Temp Units  
Pressure  
Percent Range  
Snsr Temp  
Snsr  
Trim Pts.  
PROCESS  
VARIABLES  
7
8
9
RANGE VALUES  
1
2
Keypad Input  
Apply Values  
Unit  
2
3
4
SIGNAL  
CONDITION  
Transfer Function  
10 Damp  
1
2
3
4
Pressure  
Percent Range  
Analog Output  
Snsr Temp  
1
2
3
4
PROCESS  
VARIABLES  
ANALOG  
OUTPUT  
1
2
Loop Test  
Digital-to-Analog  
Trim  
Analog Output  
Alarm  
3
Scaled D/A Trim  
4
DETAILED  
SETUP  
OUTPUT  
CONDITION  
1
Poll Address  
HART OUTPUT  
2
3
4
Nmbr of Request Pream  
Burst Mode  
1
2
3
4
5
6
Tag  
Burst Option  
Date  
1
FIELD DEVICE  
INFO  
Descriptor  
Message  
Model  
1
2
Meas. Type  
Isolator  
Mtrl.  
2
3
4
SENSOR INFO  
METER TYPE  
Self Test  
Write  
Protect  
Local Keys  
Revisions  
#s  
1
2
% Range  
3
4
Fill Type  
Flange  
7
8
DEVICE INFO  
Alt. %  
Range  
Type  
5
Flange Mat.  
5
REVIEW  
6 O-Ring Mat.  
7
8
DV Mat.  
# of Rmt  
Seals  
9
RS Type  
10 RS Mat.  
11 RS Fill  
3-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 3081C Conductivity Transmitter  
1 C  
2 T  
3 L  
1 VIEW FLD DEV  
VARS  
1 PV is  
2 C  
3 T  
4 L  
5 R  
6 NaOH  
7 HCl  
8 H2SO4 low  
9 H2SO4 hi  
10 Cond % rnge  
11 AO  
4 R  
5 NaOH  
6 HCl  
7 H2SO4 low  
8 H2SO4 hi  
9 Temp  
10 A  
1 PROCESS  
VARIABLES  
1 Begin  
procedure  
2 C  
3 T  
4 L  
5 R  
6 NaOH  
7 HCl  
8 H2SO4 low  
9 H2SO4 hi  
10 Cell const  
11 Cal const  
12 Cell factor  
2 VIEW PV-  
ANALOG 1  
3 Vew status  
1 View status  
2 Master reset  
3 View history  
1 TEST DEVICE  
2 Loop test  
3 CALIBRATION  
4 D/A trim  
2 DIAG/  
SERVICE  
1 STANDARDIZE  
PV  
5 Hold mode  
1 Sensor zero  
2 C  
2 INITIAL SETUP  
3 T  
4 L  
5 R  
6 NaOH  
1 Tag  
3 ADJUST  
TEMPERATURE  
1 Begin procedure  
2 Temp  
3 Temp comp  
4 Man. temp  
7 HCl  
3 BASIC  
SETUP  
8 H2SO4 low  
9 H2SO4 hi  
10 Cell const  
11 Cell factor  
12 Cal const  
13 Slope  
14 Temp slope cal  
1 Cond LRV  
2 Cond URV  
3 C  
4 T  
5 L  
2 PV RANGE  
VALUES  
6 R  
7 NaOH  
8 HCl  
9 H2SO4 low  
10 H2SO4 hi  
11 Cond % rnge  
12 Cond xfer fun  
1 Tag  
3 DEVICE  
INFORMATION  
2 Descriptor  
3 Message  
4 Snsr text  
5 Date  
1 PV is  
2 Meas. range  
3 Slope  
4 Cell const  
5 Cal const  
6 Cell factor  
1 SENSORS  
1 MAIN SENSOR  
2 TEMPERATURE  
1 Temp comp  
2 Man. temp  
3 Temp snsr  
4 DETAILED  
SETUP  
1 Cond LRV  
2 Cond URV  
3 C  
2 SIGNAL  
CONDITION  
4 T  
5 L  
6 R  
7 NaOH  
3 OUTPUT  
CONDITION  
1 ANALOG OUTPUT  
2 HART OUTPUT  
4 DEVICE  
INFORMATION  
8 HCl  
9 H2SO4 low  
10 H2SO4 hi  
11 Cond % rnge  
12 Cond xfer fun  
1 SENSORS  
2 OUTPUTS  
3 DEVICE  
5 LOCAL  
DISPLAY  
5 REVIEW  
INFORMATION  
4 LOCAL DISPLAY  
3-14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 3081FG Oxygen Analyzer  
1 O2 value  
1 VIEW FLD DEV  
2 Cell Temp  
1 PV is  
VARS  
2 O2 value  
3 % rnge  
4 O2 output  
1 PROCESS  
VARIABLES  
3 Cell mV  
2 VIEW OUTPUT  
VARS  
1 VIEW PV-AOUT  
2 VIEW SV  
1 SV is  
2 SV  
1 Device Status  
2 Loop test  
1 TV is  
2 TV  
3 VIEW TV  
4 VIEW 4V  
1 4V is  
2 4V  
2 DIAG/SERVICE  
1 Start Calcheck  
2 OPtrakTG?  
3 HighTG  
3 O2 CALCHECK  
4 D/A trim  
4 LowTG  
5 Slope  
6 Constant  
1 Max Temp  
5 MAX CELL TEMP  
1 Tag  
2 Reset Max Temp  
3 BASIC SETUP  
2 SELECT O2  
RANGE  
1 URV  
1 Dev id  
1 DEVICE  
SETUP  
2 PV  
3 PV AO  
3 LRV  
4 URV  
2 Descriptor  
3 Message  
4 Date  
5 Final asmbly num  
6 Snsr s/n  
3 Alarm value  
4 DEVICE  
INFORMATION  
1 Ver  
2 Bld  
3 Bld Date  
5 Device SN  
6 Alarm value  
5 S/W VERSION INFO  
1 O2 value  
2 Snsr unit  
3 USL  
1 O2  
4 LSL  
5 Min span  
1 SENSORS  
1 Cell Temp  
2 Snsr unit  
3 USL  
4 LSL  
5 Min span  
4 DETAILED  
SETUP  
2 CELL TEMP  
3 02 CELL IMP  
1 Cell mV  
2 Snsr unit  
3 USL  
4 LSL  
5 Min span  
1 URL  
2 LRV  
3 % rnge  
2 SIGNAL  
CONDITION  
1 O2 output  
2 AO Alrm typ  
3 Loop test  
3 D/A trim  
3 OUTPUT  
CONDITION  
1 ANALOG  
OUTPUT  
4 Filter  
2 HART  
1 Poll addr  
OUTPUT  
2 Num req preams  
1 DEVICE  
INFORMATION  
2 OUTPUTS  
CONFIG  
5 REVIEW  
3-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 3081pH Transmitter  
1
2
3
4
5
6
Ph  
1
PROCESS  
VARIABLE  
1
VIEW FIELD  
DEVICE  
VARIABLES  
ORP  
Temperature  
Input  
Glass  
Ref  
2
VIEW PV-  
1
PV is  
ANAOLOG 1  
2
3
4
PV  
PV % Range  
PV A/O  
3
View Status  
1
2
3
4
Begin Procedure  
Slope  
0 Offset  
pH  
1
2
3
View Status  
Master Reset  
View History  
1
TEST DEVICE  
1
2
3
BUFFER CALIBRATION  
STANDARDIZE PV  
1
2
3
Begin Procedure  
pH  
2
Loop Test  
2
DIAGNOS  
AND  
0 Offset  
SERVICE  
3
CALIBRATION  
1
2
3
4
Begin Procedure  
Temp  
Temp Comp  
Man. Temp  
ADJUSTMENT  
TEMPERATURE  
4
Trim Analog Output  
5
Hold Mode  
Tag  
1
2
3
4
5
6
pH LRV  
pH URV  
1
2
3
pH ORP  
pH pH  
pH % Range  
pH Xfer Fun  
1
2
3
4
5
Tag  
3
BASIC  
SETUP  
PV RANGE VALUES  
Descriptor  
Message  
Snsr Text  
Date  
DEVICE INFORMATION  
1
2
3
4
5
6
7
8
PV is  
Conventional  
Autocal  
SST  
1
MAIN SNSR  
TEMP  
1
SENSOR  
1
2
3
Temp Comp  
Man Temp  
Temp Snsr  
SSS  
2
Imped Comp  
Oper iso  
TOC  
1
pH LRV  
pH URV  
pH ORP  
pH  
pH % Range  
pH xfer fun  
2
3
4
5
6
2
SIGNAL  
CONDITION  
1
PV A/O  
2
3
4
PV A/O Damp  
PV Hold  
1
2
3
ANALOG OUT  
Loop Test  
Trim A/O  
1
ANALOG OUTPUT  
HART OUTPUT  
PV Fault  
3
4
OUTPUT  
4
DETAILED  
SETUP  
CONDITION  
2
1
Poll Address  
Temp Unit  
Ref Unit  
Burst Option  
Burst Mode  
Num Resp  
2
3
4
5
6
1
2
3
4
5
Tag  
Descriptor  
Message  
Snsr Text  
Date  
DEVICE INFO  
1
Diagnostics  
GFH  
2
3
4
5
6
7
8
9
5
6
DIAGNOSTIC  
LOCAL DISP  
GFL  
Ref Unit  
RFH  
RFL  
GWH  
GWL  
RWH  
1
2
Xmtr  
A/O LOI Units  
10 RWL  
5
REVIEW  
11 0 Limits  
12 Cal Warn  
3-16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 3095C Level Controller  
1 LEVEL (LV)  
1 More Level  
Setup  
2 Level  
3 LV Unit  
4 Range values  
5 LV Damping  
6 LV Trim  
1 DP  
1 PROCESS  
VARIABLES  
2 DP unit  
3 DP Damping  
4 DP Sensor  
Trim  
2 PRESSURE (DP)  
5 Dp USL  
6 DP LSL  
1 RTD  
2 PT  
3 TEMPERATURE (PT)  
1 CONTROL LOOP  
3 PT unit  
4 PT Damping  
5 PT Sensor  
Trim  
1 More Control  
Setup  
2 P: Gain  
2 CONTROLLER  
6 PT USL  
7 PT LSL  
3 I: Reset  
4 D: Rate  
5 Deriv Fltr  
6 Bias  
7 Balance Time  
8 Adapt Bias Ctl  
9 ABC Static Error  
10 ABC Stablty  
Thrsh  
1 Setpoint  
2 SP Active  
3 SP Rate  
4 SP Hi Lim  
5 SP Lo Lim  
6 SP Track  
2 SETPOINT  
OPTIONS  
1 Level  
2 Setpoint  
3 Target Mode  
4 Manual  
5 Ctl Out  
6 Anlg sgnl  
7 DEVICE SETUP  
1 Target Mode  
2 Actual Mode  
3 Shed Act  
4 Shed Out  
5 Shed Ret  
3 MODE  
SUPERVISOR  
1 Tuner  
2 Tuning Status  
3 AUTO-TUNE  
SETUP  
4 Perform  
Auto-Tune  
6 Power-up  
4 AUTO TUNING  
1 Ctl Out  
2 Manual  
3 Man Rate Limit  
5 MANUAL MODE  
SETUP  
5 Accept  
Auto-Tune  
6 Tuning Gain  
7 Tuning Reset  
8 Tuning Rate  
9 Process Gain  
10 Process delay  
11 Tuning Bias  
1 D/A trim  
2 Scaled D/A trim  
3 Factory D/A Trim  
3 SENSOR TRIM  
4 Loop test  
5 View status  
6 Reset  
3 DIAG/SERVICE  
1 LV Trim  
2 DP Sensor Trim  
3 PT Sensor Trim  
1 Isolatr matl  
2 Fill fluid  
1 HART OUTPUT  
3 Flnge matl  
4 Flange type  
5 Drain vent matl  
5 O ring matl  
6 RS type  
7 RS fill fluid  
8 RS isoltr matl  
9 Num remote seal  
2 CONSTRUCTION  
MATLS  
4 GENERAL  
SETUP  
3 DEVICE  
I NFORMATION  
1 Universal rev  
2 Fld dev rev  
3 Software rev  
4 Hardware rev  
5 Snsr Module sw  
rev  
4 REVISION #'S  
6 Snsr Module hw  
rev  
5 LOI  
CONFIGURATION  
5 REVIEW  
3-17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 3095MV Multivariable Transmitter  
1
PROCESS  
VARIABLES  
1
2
3
4
5
Pres  
1
2
3
Diff Pres  
Static Pres  
Process Temp  
% rnge  
1
2
3
4
5
PV  
A/O  
SV  
VIEW FLD DEV VAR  
VIEW OUTPUT VAR  
TV  
4V  
OutPut Var Units  
1
2
3
1
2
Loop Test  
View Status  
Reset  
1
2
TEST STATUS  
CALIBRATION  
1
2
3
DP Sens Trim  
SP Sens Trim  
Temp Sens Trim  
2
DIAGNOSTIC  
AND  
SERVICE  
SENSOR TRIM  
ANALOG TRIM  
1
2
3
D/A Trim  
Scaled D/A Trim  
Factory Trim  
1
2
3
DP Unit  
SP Unit  
1
Tag  
1
2
3
4
5
6
7
8
9
Tag  
2
XMTR VAR ENG  
UNITS  
Temp Unit  
Descriptor  
Message  
Date  
3
4
5
Range Values  
DEVICE INFO  
CONTRUCTION  
MATS  
Final Assbly num  
Manufacture  
Model  
Write Protect  
Revision #’s  
3
BASIC SETUP  
1
DP Snsr Range  
SP Snsr Range  
SP Type  
Isoltr Matrl  
Fill Fluid  
Flnge Matrl  
Flnge Type  
Drain Vent Matrl  
O Ring Matrl  
2
3
4
5
6
7
8
9
10 RS Type  
11 RS Fill Fluid  
12 RS Isoltr Matrl  
13 Num Remt Seal  
1
2
3
A/O Alrm Type  
Loop Test  
1
2
ANALOG OUT  
HART OUTPUT  
1
OUTPUT  
CONDITION  
Analog Trim  
1
2
3
4
5
DEVICE SETUP  
PV  
1
2
3
4
Poll Addr  
PV AO  
Num Req Preams  
Num Resp Preams  
Burst Mode Opr  
4
DETAILED  
SETUP  
PV LRV  
PV URV  
1
Sensor Temp  
Analog Trim  
1
CALIBRATION  
RTD Config  
PVDamp  
2
2
3
4
2
SIGNAL  
CONDITION  
1
2
3
DP Damping  
SP Damping  
Temp Damping  
Xmtr Var  
Damp  
5
Xmtr Var Eng  
Unit  
1
2
3
DP Unit  
SP Unit  
Temp Unit  
5
REVIEW  
3-18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 3144 Temperature Transmitter  
1
2
3
PROCESS  
1
2
3
4
5
6
7
PV Eng Units  
VARIABLES  
PV $% Rnge  
PV A/O Output  
VIEW FLD DEV VAR  
SV  
Variable Mapping  
VARIABLE RE_MAP  
1
2
PV  
SV  
1
2
Terminal Temp  
Sensor 1  
1
Status  
Self Test  
Master Test  
1
TEST DEVICE  
2
3
DIAGNOSTIC  
AND SERVICE  
1
4 ma  
20 ma  
Other  
End  
2
3
4
2
3
4
LOOP TEST  
1
2
3
4
5
PV LRV  
PV URV  
PV Eng Units  
Lower Snsr Unit  
Upper Snsr Unit  
CALIBRATION  
Smart Calibration  
1
Apply Values  
2
3
4
5
6
7
RANGE VALUES  
SENSOR TRIM  
D/A Trim  
1
2
Snsr 1 Input Trim  
Snsr 1 Trim-  
Factory  
Scaled D/A Trim  
CJC Cal. Value  
RTD Current  
BASIC SETUP  
1
Tag  
PV Unit  
2
3
4
5
6
Range Values  
SENSOR 1 CONN  
PV Damp  
1
Number of Wires  
1
Select Snsr Type  
Sensor 1 Snsr s/n  
1
2
3
4
5
PV  
1
2
Snsr  
PV Unit  
1
PROCESS  
SENSOR  
Config  
Misc  
Snsr Setup  
Snsr Info  
Snsr Trim  
1
SENSORS  
Config  
2
TERM TEMP  
SNSR  
1
2
3
4
Term Temp  
Unit  
Damp  
3
A/D Conver  
Info  
1
2
3
4
5
DEVICE SETUP  
PV  
Term Temp Lmts  
PV AO  
2
3
SIGNAL  
1
2
3
4
PV LRV  
PV LRV  
PV URV  
4
DETAILED  
SETUP  
CONDITION  
PV URV  
1
A/O Output  
A/O Alrm Type  
LOOP TEST  
D/A Trim  
Scaled D/A  
Trim  
PV % Rnge  
PV Damp  
1
2
3
4
4 ma  
20 ma  
Other  
End  
2
3
4
5
1
ANALOG  
OUTPUT  
OUTPUT  
CONDITION  
1
Poll Address  
2
3
4
Num Reqst Preams  
Burst Mode  
2
3
HART  
OUTPUT  
Burst Opts  
METER  
OPTIONS  
1
2
3
Meter Type  
Meter Dec. Pt.  
Meter Bar Graph  
1
2
3
4
Date  
4
DEVICE  
INFO  
5
REVIEW  
Descriptor  
Message  
Other Info  
3-19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 3201 Hydrostatic Interface Unit  
1 PRODUCT  
1 CONSTANTS  
CONSTANTS  
1 Level  
2 TANK  
2 T Mass  
3 E Mass  
4 StdVol  
5 GrsVol  
6 StdDen  
7 MeaDen  
8 Prdtmp  
9 TnkAl  
10 StatAl  
11 DiagAl  
12 TstAll  
13 TstBlk  
14 Pb  
1 SET UP  
CONSTANTS  
1 TblSiz  
2 StrTmp  
3 StrDns  
4 Strap Table Edit  
2 STRAPPING  
DATA  
1 ModAdd  
2 BaudRt  
3 MODBUS  
SCALING  
3 COMMUNICATIONS  
1 PtType  
2 PmType  
3 SwType  
4 TmpTyp  
5 WBType  
4 User Reg Map  
4 DEVICE  
TYPES  
15 Pm  
16 Pt  
1 DISPLAY SEL  
PRIM  
5 DISPLAY  
SELECT  
1 RfMass  
2 TnkCap  
3 Ullage  
4 WBVol  
5 MBLev  
6 AvlPrd  
7 Tm2Com  
8 Flow  
9 Spec1  
10 Spec2  
11 Spec3  
12 Spec4  
13 Spec5  
2 DISPLAY SEL  
OTHER  
1 Mass  
6 UNITS SELECT  
7 TRANSFER  
2 MeaDen  
3 StdDen  
4 Volume  
5 Level  
6 Temp  
7 Press  
8 Flow  
1 TnkSta  
2 Flow  
3 XfrDon  
4 SfrLft  
5 Tm2Cmp  
6 XfrSP  
7 XfrDel  
8 FlwPer  
9 HFlwSP  
10 LFlwSP  
11 XfrWrn  
9 XferSP  
1 PV is  
2 URV  
3 LRV  
4 OUTPUT  
TRIM  
8 ANALOG  
OUTPUT  
1 D/A trim  
2 Scaled D/A  
trim  
1 CALCULATED DATA  
2 PROC VARIABLE  
3 ALARMS  
2 MEASURED DATA  
1 TANK ALARMS  
1 ALARM SETPOINTS  
2 ALARM ENABLES  
3 ALARM STATUS  
2 STATUS ALARMS  
3 DIAGNOSTIC  
ALARMS  
1 TEST PROCESS  
ALRM  
4 TEST  
2 Loop test  
1 Tag  
2 Descriptor  
3 Message  
4 Date  
5 DEVICE INFO  
1 ManLev  
2 ManTmp  
3 ManWBL  
4 ManStD  
6 AUTO/MANUAL  
3-20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 3202 Smart Application Module  
1 PRODUCT CONSTANTS  
2 TANK CONSTANTS  
1 CONSTANTS  
1 SET UP  
1 TblSiz  
2 StrTmp  
3 StrDns  
4 STRAPPING TABLE  
1 POINTS 0-4  
2 POINTS 5-9  
3 POINTS 10-14  
4 POINTS 15-19  
2 STRAPPING  
TABLE  
1 ModAdd  
2 BaudRt  
3 MODBUS SCALING  
3 COMMUNICATIONS  
4 DEVICE TYPES  
1 INT ASSIGN 0-9  
2 INT ASSIGN 10-19  
3 INT ASSIGN 20-29  
4 INT ASSIGN 30-39  
5 INT ASSIGN 40-49  
4 USER ASSIGN REG  
1 PtType  
2 PmType  
3 TmpTyp  
1 Mass  
1 DISPLAY SEL PRIM  
2 DISPLAY SEL  
OTHER  
5 DISPLAY  
SELECT  
2 MeaDen  
3 StdDen  
4 Volume  
5 Level  
6 UNITS SELECT  
6 Temp  
7 Press  
1 PV is  
2 URV  
3 LRV  
4 OUTPUT TRIM  
7 ANALOG  
OUTPUT  
1 D/A trim  
2 Scaled D/A trim  
1 E Mass  
1 CALCULATED  
DATA  
2 T Mass  
3 MeaDen  
4 StdDen  
5 Level  
6 GrsVol  
7 StdVol  
8 AlphaT  
9 AvlPrd  
1 Pb  
2 Pm  
3 Pt  
4 RTDres  
5 RTDtmp  
6 Tb  
7 Tm  
8 Tt  
2 PROC VARIABLE  
10 PrdTmp  
11 AmbTmp  
2 MEASURED  
DATA  
9 SAMtmp  
1 TANK  
ALARMS  
1 ALARM  
SETPOINTS  
2 ALARM ENABLES  
3 ALARM STATUS  
3 ALARMS  
4 TEST  
1 TEST PROCESS  
ALRM  
2 Loop test  
1 Pb<Pm  
2 Pb<Pt  
3 Pm<Pt  
4 NoDClc  
5 Strap  
6 RTDNIm  
7 NoCalc  
8 PrdSol  
2 STATUS  
ALARMS  
1 Tag  
2 Descriptor  
3 Message  
4 Date  
5 DEVICE INFO  
1 ManLev  
2 ManTmp  
3 ManStD  
3 DIAGNOSTIC  
ALARMS  
6 AUTO/MANUAL  
3-21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 3244 Temperature Transmitter  
1
2
3
4
PV  
SV  
TV  
QV  
1
2
3
4
5
6
7
8
PV Eng Units  
PV $% Rnge  
PV A/O Output  
SV  
1
PROCESS  
VARIABLES  
1
2
3
4
Differential Temp  
Terminal Temp  
Sensor 1  
TV  
QV  
VARIABLE REMAP  
VARIABLE RE-MAP  
Sensor 2  
1
2
3
Status  
1
TEST DEVICE  
Self Test  
Master Test  
2
DIAGNOSTIC  
AND  
SERVICE  
1
2
3
4
4 ma  
20 ma  
Other  
End  
2
3
4
LOOP TEST  
1
2
3
4
5
PV LRV  
PV URV  
PV Eng Units  
Lower Snsr Lmts  
Upper Snsr Lmt  
1
2
Apply Values  
TERM TEMP SNSR  
CALIBRATION  
Smart Calibration  
1
Snsr 1 Input Trim  
Snsr 2 Input Trim  
Snsr 1 Trim-Fac  
Snsr 2 Trim-Fac  
3
4
5
6
7
SENOR TRIM  
D/A Trim  
Scaled D/A Trim  
CJC Cal. Value  
RTD Current  
2
3
4
1
2
3
4
5
6
7
8
Tag  
PV Unit  
Range Values  
SENSOR 1 CONN  
SENSOR 2 CONN  
PV Damp  
3
BASIC SETUP  
1
Number of Wires  
1
Select Sensor type  
Sensor 1 Snsr s/n  
Sensor 2 Snsr s/n  
1
2
3
4
PV  
PV Unit  
SENSOR SETUP  
sensor Info  
SENSOR TRIM  
1
PROCESS  
SENSOR  
5
1
Term Temperature  
Unit  
2
TERM TEMP  
SENSOR  
1
SENSORS  
2
3
4
Damping  
Term Temp Limits  
3
A/D Conver  
Info  
1
50/60 Hz filter  
1
2
3
4
PV LRV  
1
2
3
4
5
DEVICE SETUP  
PV  
2
3
SIGNAL  
1
4 ma  
20 ma  
Other  
End  
PV URV  
1
2
3
4
5
A/O Output  
A/O Alrm Type  
LOOP TEST  
D/A Trim  
Scaled D/A  
Trim  
CONDITION  
2
3
4
4
DETAILED  
SETUP  
PV % Rnge  
PV Damp  
PV AO  
PV LRV  
PV URV  
1
ANALOG  
OUTPUT  
OUTPUT  
CONDITION  
1
Poll Address  
2
3
4
Numr Reqsat Preams  
Burst Mode  
2
3
HART  
OUTPUT  
Burst Options  
1
2
3
Meter Type  
Meter Dec. Pt  
Meter Bar Graph  
METER  
OPTIONS  
1
2
3
DP Unit  
SP Unit  
Temp Unit  
5
REVIEW  
4
DEVICE INFO  
3-22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 3680 Density Transmitter  
1
2
3
4
5
Process Variable  
PV Percent Range  
PV Output  
1
PROCESS  
VARIABLES  
PV Units  
Temp  
1
2
3
4
Last Reference  
Counts  
Reference Material  
New Reference  
1
REFERENCE  
1
2
3
Test Device  
Loop Test  
CALIBRATE  
2
Calibration Curve  
2 DIAGNOSTICS  
AND SERVICE  
3
PROCESS  
SAMPLE  
1
2
3
Sample  
Sample Duration  
New Sample  
4
Density Offset  
1
2
3
4
5
6
7
PV Units  
1
Tag  
Upper Range Value  
Lower Range Value  
Upper Sensor Limit  
Lower Sensor Limit  
Density of Carrier  
Density of Material  
2
RANGE & UNITS  
3
BASIC SETUP  
1
2
3
Date  
Time – Hours  
Time – Minutes  
3
4
DATE & TIME  
DAMPING  
1
2
3
Adaptive Damp Status  
Adaptive Damp Value  
Damping Threshold  
1
2
PV Damp  
ADAPTIVE DAMPING  
1
Temperature  
Compensation  
Status  
1
TEMPERATURE  
COMPENSATION  
1
2
3
4
5
6
Reference Temperature  
Expansion Coefficient  
Rho 1  
Temperature 1  
Rho 2  
Temperature 2  
1
DEVICE  
SETUP  
PV  
PV Output  
LRV  
URV  
2
Temperature Units  
2
3
4
5
3
COMPENSATION  
PARAMETERS  
4
SENSOR TYPE  
1
2
3
RTD  
4 to 20 mA  
None  
4
DETAILED  
SETUP  
1
2
Digital-to-Analog Trim  
Scaled D/A Trim  
2
OUTPUT TRIM  
1
Source Type  
Last Setup Location  
Sensor s/n  
UNIVERSAL  
VARIABLES  
Pipe Description  
Process Description  
Message  
2
3
4
1
2
3
Manufacturer  
Model  
Poll Address  
5
6
7
8
9
3
FIELD DEVICE  
INFORMATION  
Descriptor  
Final Assembly Number  
Software Revision  
5
REVIEW  
3-23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 3809/3810 Variable Area Meter  
1 PV  
2 % rnge  
1 PROCESS  
VARIABLES  
1 Alrm  
2 Reset alarm  
3 STATUS  
4 Seq no  
2 DIAGS &  
SERVICES  
5 FltPos  
1 Loop Test  
6 Int Temp  
7 TEST DEVICE  
2 Pulse O/P Test  
3 CONTACT O/PS  
4 Warning Level  
1 Tag  
2 Model  
3 Ser No  
4 CONFIGURATION  
1 Cutoff  
2 CalFact  
1 AO  
2 % rnge  
3 URV  
3 BASIC  
SETUP  
5 ANALOG  
OUTPUT  
4 LRV  
5 Damp  
6 AO Alrm typ  
1 Unit  
6 PULSE OUT  
2 Scaler  
3 Width  
1 FlowRate Units  
2 CONFIGURATION  
3 METER  
CALIBRATION  
1 FLOW  
1 DEVICE  
SETUP  
2 PV  
3 AO  
4 URV  
5 LRV  
1 MEASUREMENTS  
2 TEMPERATURE  
3 DENSITY  
4 PRESSURE  
5 VISCOSITY  
1 INVENTORY  
1 TOTALIZERS  
2 COMPUTATIONS  
3 OUTPUTS  
2 RESETTABLE  
4 DETAILED  
SETUP  
1 AO  
2 % rnge  
3 URV  
4 LRV  
5 Damp  
6 AO Alrm typ  
1 ANALOG OUTPUT  
2 CONTACT OUTPUT 1  
3 CONTACT OUTPUT 2  
4 PULSE OUT  
1 Num req preams  
2 Poll addr  
5 HART OUTPUT  
1 Alrm  
1 Alarm Status  
2 Diagnostic Status 1  
2 Reset Alarm  
3 STATUS  
4 ALARM  
CONFIG  
4 ALARMS  
1 Tag  
2 Descriptor  
3 Message  
4 Date  
5 Model  
6 Ser No  
7 Manufacturer  
8 Dev id  
9 REVISION INFO  
10 FLOW METER  
11 ACCESSORIES  
12 W & M  
5 DEVICE INFO  
3-24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 4000 Oxygen Analyzer  
1 O2 value  
2 O2 Cell temp  
3 CJ temp  
1 PV is  
1 VIEW FLD DEV  
VARS  
2 O2 value  
3 % rnge  
4 O2 output  
1 PROCESS  
VARIABLES  
1 VIEW PV-AOUT  
2 VIEW SV  
1 SV is  
2 O2 value  
2 VIEW OUTPUT  
VARS  
1 TV is  
2 O2 value  
3 VIEW TV  
1 4V is  
2 O2 value  
4 VIEW 4V  
1 Cell mV  
2 Cell TC mv  
3 CJ mV  
3 VIEW FLD DEV  
MV  
1 STATUS  
1 PERFORM O2 CAL  
2 O2 CAL STATUS  
2 DIAG/  
SERVICE  
2 Loop test  
3 LAST  
CALCONSTANTS  
3 O2 CALIBRTION  
4 D/A trim  
1 DEVICE SETUP  
2 PV  
3 PV AO  
4 Reset CalConstants  
4 PV LRV  
5 PV URV  
1 Tag  
1 PV is  
2 SV is  
3 TV is  
4 4V is  
2 ASSIGN PV & SV  
3 BASIC  
SETUP  
3 SELECT O2  
RANGE  
1 URV  
2 LRV  
1 Dev id  
2 Descriptor  
3 Message  
4 Date  
5 Final asmbly num  
6 Snsr s/n  
4 DEVICE  
INFORMATION  
1 Ver  
2 Chksum  
3 Bld Num  
4 Bld Date  
5 S/W VERSION  
INFO  
1 O2  
2 O2 CELLTEMP  
3 COLDJUNCTEMP  
4 O2 CELL MV  
5 O2 CELLTCMV  
6 COLDJUNC MV  
1 SENSORS  
4 DETAILED  
SETUP  
1 URV  
2 LRV  
3 % rnge  
2 SIGNAL  
CONDITION  
1 ANALOG OUTPUT  
3 HART OUTPUT  
3 ALARM OUTPUT  
3 OUTPUT  
CONDTION  
1 Slope  
2 Constant  
4 O2  
5 REVIEW  
5 O2 CALIBRATION  
6 O2 ALARMS  
3-25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 8712C Mag Flow Transmitter  
1
2
3
4
5
Process Variable  
Pulse Output  
Measure Gross Total  
Measure Net Total  
Measure Reverse Total  
1
2
PROCESS  
VARIABLES  
1
2
3
4
TEST STATUS  
Auto Zero  
1
2
Status  
1
TEST DEVICE  
Loop Test  
Self Test  
2
3
4
DIAGNOSTIC  
S AND  
SERVICE  
1
2
Digital-to-Analog Trim  
Scaled D/A Trim  
OUTPUT TRIM  
Digital Trim  
Calibration  
Digital-to-Analog Trim  
1
2
3
4
5
6
7
8
9
PV Unit  
Upper Range Value  
Lower Range Value  
Line Size  
Calibration Number  
PV Damp  
Tag  
Message  
Descriptor  
Date  
3
BASIC SETUP  
1
SENSOR  
1
Process  
1
2
3
4
5
Zero Trim  
Variable  
Base Volume Unit  
Conversion Number  
Base Time Unit  
Flow Rate Unit  
1
2
PV Units  
SPECIAL  
2
3
4
FLOW UNITS  
Sensor Info  
Sensor  
Configuration  
1
2
3
4
5
PV % Range  
Upper Range Value  
Lower Range Value  
PV Damp  
2
3
INPUT  
1
2
3
4
Status  
Samples  
Percent Rate  
Time Limit  
SIGNAL PROCESSING  
1
2
3
4
5
DEVICE SETUP  
PV  
AO  
LRV  
URV  
1
2
3
Totalizer Value  
1
2
3
Pulse Scaling  
Pulse Width  
Pulse Output  
Loop Test  
Totalizer Display  
PULSE OUTPUT  
CONFIGURATION  
Totalizer Control  
TOTALIZER  
4
4
DETAILED  
SETUP  
1
2
3
4
5
Analog Output  
AO Alarm Type  
Loop Test  
Digital-to-Analog Trim  
Scaled D/A Trim  
1
2
3
4
Meter Type  
ANALOG  
HART  
4
OUTPUTS  
1
2
3
Poll Address  
Number of Request Preambles  
Burst Mode  
Auxiliary  
1
2
3
4
5
6
7
8
Distributor  
Tag  
Descriptor  
Message  
Date  
Device ID  
Write Protect  
CONSTRUCTION  
MATERIALS  
5
REVIEW  
1
2
3
4
5
Flange Type  
5
DEVICE INFO  
Flange Material  
Electrode Type  
Electrode Material  
Liner Material  
9
Flow Tube Tag  
Revision Number  
Self Test  
3-26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 8712C+ Mag Flow Transmitter  
1
2
3
4
5
Process Variable  
Pulse Output  
Measure Gross Total  
Measure Net Total  
Measure Reverse Total  
1
2
PROCESS  
VARIABLES  
1
2
3
4
TEST STATUS  
Auto Zero  
1
2
Status  
1
TEST DEVICE  
Loop Test  
Self Test  
2
3
4
DIAGNOSTICS  
AND SERVICE  
1
2
Digital-to-Analog Trim  
Scaled D/A Trim  
OUTPUT TRIM  
Digital Trim  
Calibration  
Digital-to-Analog Trim  
1
PV Unit  
2
3
4
5
6
7
8
9
Upper Range Value  
Lower Range Value  
Line Size  
1
2
Vol unit  
Base Volume  
Unit  
Conversion  
Number  
Base Time Unit  
Flow Rate Unit  
Calibration Number  
PV Damp  
1
2
PV Units  
SPECIAL  
3
3
BASIC SETUP  
Tag  
4
5
Descriptor  
Message  
1
2
3
PV LSL  
PV USL  
Lo Flo  
Cutoff  
PV Min  
Span  
10 Date  
1
2
3
4
Process Variable  
FLOW UNITS  
SENSOR INFO  
SNSR CONFIG  
1
SENSOR  
4
5
1
Line Size  
2
Calib Num  
COIL FREQ  
CONFIG  
PV Snsr  
s/n  
3
4
5
Auto Zero  
PV Snsr s/n  
1
PV % Range  
2
3
4
5
Upper Range Value  
Lower Range Value  
PV Damp  
1
2
3
4
Status  
2
3
INPUT  
Samples  
1
DEVICE  
SETUP  
PV  
Percent Rate  
Time Limit  
SIGNAL PROCESSING  
2
3
4
5
AO  
1
2
3
Totalizer Value  
LRV  
URV  
1
2
3
Pulse Scaling  
Pulse Width  
Pulse Output  
Loop Test  
Totalizer Display  
PULSE OUTPUT  
CONFIGURATION  
Totalizer Control  
TOTALIZER  
4
4
DETAILED  
SETUP  
1
2
3
4
5
Analog Output  
AO Alarm Type  
Loop Test  
Digital-to-Analog Trim  
Scaled D/A Trim  
1
Meter Type  
2
3
4
ANALOG  
HART  
1
2
3
4
Poll Address  
4
OUTPUTS  
Number of Request Preams  
Burst Mode  
Auxiliary  
Burst Option  
1
2
3
4
5
6
7
Tag  
Distributor  
Descriptor  
Message  
Date  
1
Flange Type  
2
3
4
5
Flange Material  
Electrode Type  
Electrode Material  
Liner Material  
Device ID  
Write Protect  
5
REVIEW  
8 CONSTRUCTION  
MATERIALS  
5
DEVICE INFO  
9
Flow Tube Tag  
1
Universal Rev  
Fld Dev Rev  
Software Rev  
10 REVISION #s  
2
11 Self Test  
3
3-27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 8712U+ Mag Flow Transmitter  
1
2
3
4
5
Process Variable  
Pulse Output  
Measure Gross Total  
Measure Net Total  
Measure Reverse Total  
1
PROCESS  
VARIABLES  
1
2
3
4
TEST STATUS  
Auto Zero  
1
2
Status  
1
TEST DEVICE  
Loop Test  
Self Test  
2
3
4
Calibration  
2 DIAGNOSTICS  
AND SERVICE  
Digital-to-Analog Trim  
1
2
Digital-to-Analog Trim  
Scaled D/A Trim  
OUTPUT TRIM  
Digital Trim  
1
PV Unit  
2
3
4
5
6
7
8
9
Upper Range Value  
Lower Range Value  
Line Size  
Calibration Number  
Universal Trim  
Coil Current  
Transmitter Gain  
Flowtube Gain  
1
2
Vol unit  
Base Volume  
Unit  
Conversion  
Number  
Base Time Unit  
Flow Rate Unit  
3
BASIC SETUP  
1
2
PV Units  
SPECIAL  
3
10 PV Damp  
11 Tag  
12 Descriptor  
13 Message  
14 Date  
4
5
1
PV LSL  
PV USL  
Lo Flo  
Cutoff  
2
3
1
2
3
4
Process Variable  
FLOW UNITS  
SENSOR INFO  
SNSR CONFIG  
1
SENSOR  
4
5
PV Min  
Span  
1
Line Size  
2
Calib Num  
COIL FREQ  
CONFIG  
PV Snsr  
S/N  
3
4
5
Auto Zero  
PV Snsr S/N  
1
PV % Range  
2
3
4
5
Upper Range Value  
Lower Range Value  
PV Damp  
1
2
3
4
Status  
2
3
INPUT  
Samples  
1
DEVICE  
SETUP  
PV  
Percent Rate  
Time Limit  
SIGNAL PROCESSING  
2
3
4
5
AO  
1
Totalizer Value  
LRV  
URV  
1
2
3
Pulse Scaling  
Pulse Width  
Pulse Output  
Loop Test  
2
Totalizer Display  
PULSE OUTPUT  
CONFIGURATION  
Totalizer Control  
3
TOTALIZER  
4
4
DETAILED  
SETUP  
1
2
3
4
5
Analog Output  
AO Alarm Type  
Loop Test  
1
Meter Type  
Digital-to-Analog Trim  
Scaled D/A Trim  
2
3
ANALOG  
HART  
1
2
3
4
Poll Address  
4
OUTPUTS  
Number of Request Preams  
Burst Mode  
4
Auxiliary  
Burst Option  
1
Tag  
2
3
4
5
6
7
Distributor  
Descriptor  
Message  
Date  
1
2
3
4
5
Flange Type  
5
REVIEW  
Flange Material  
Electrode Type  
Electrode Material  
Liner Material  
Device ID  
Write Protect  
8 CONSTRUCTION  
MATERIALS  
5
DEVICE INFO  
9
Flow Tube Tag  
1
2
3
Universal Rev  
Fld Dev Rev  
Software Rev  
10 REVISION #s  
11 Self Test  
3-28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 8800 Vortex Flowmeter  
1
2
3
4
5
6
Process Variable  
PV Percent Range  
Analog Output  
Vortex Frequency  
Pulse Output  
Total  
1
2
3
PROCESS  
VARIABLES  
1
2
Self Test  
Status  
1
2
3
TEST DEVICE  
Loop Test  
CALIBRATION  
DIAGNOSTIC  
AND  
SERVICE  
1
2
Digital-to-Analog Trim  
Scaled D/A Trim  
1
2
3
4
5
6
7
8
9
Manufacturer  
Tag  
1
2
3
4
Flow Units  
Tag  
Range Values  
DEVICE INFO  
Descriptor  
Message  
1
2
3
4
5
6
Process Variable  
PV Percent Range  
Analog Output  
Vortex Frequency  
Pulse Output  
Total  
Date  
BASIC SETUP  
Device ID  
Write Protect  
CONSTRUCTION MATERIALS  
REVISION NUMBERS  
1
2
3
4
5
Volume Unit  
Base Vol Unit  
Conversion  
Base Time Unit  
Flow Rate Unit  
1
PROCESS  
VARIABLES  
1
Flow Units  
SPECIAL  
UNITS  
2
2
3
FLOW UNITS  
1
MEASURING  
ELEMENTS  
1
2
3
4
5
6
7
Line Size  
K-Factor  
Service Type  
METER  
CONFIGURATION  
Pipe Inside Diameter  
PV Sensor s/n  
Meter Body Serial  
Final Assembly Number  
1
2
3
4
5
6
SENSOR CORRECTION  
Lower Sensor Limit  
Upper Sensor Limit  
Minimum Span  
4
5
SENSOR  
Range Values  
PV Sensor s/n  
1
DEVICE  
SETUP  
PV  
1
2
Digital-to-Analog Trim  
Scaled D/A Trim  
CALIBRATION  
TEST DEVICE  
2
3
4
5
AO  
1
2
Self Test  
Status  
LRV  
URV  
6
1
PROCESS  
VARIABLES  
Range Values  
Flow Units  
CALIBRATION  
SIGNAL  
PROCESSING  
4
DETAILED  
SETUP  
1
Filter  
2
3
4
5
2
SIGNAL  
CONDITIONING  
Restore  
Low Flow  
Cutoff  
2
3
4
5
1
2
3
4
5
6
Process Variable  
PV Percent Range  
Analog Output  
Vortex Frequency  
Pulse Output  
Total  
Lowpass  
Filter  
Trigger  
Level  
Filter  
Tracking  
1
Analog Output  
AO Alarm Type  
Loop Test  
2
3
4
1
2
3
4
5
6
7
8
PROCESS VARIABLES  
Damping Value  
ANALOG OUTPUT  
PULSE OUTPUT  
TOTALIZER  
CALIBRATION  
1
2
3
Pulse Output  
Pulse Output Mode  
Pulse Output Test  
3
4
OUTPUT  
5
REVIEW  
CONDITIONING  
HART OUTPUT  
Local Display  
Loop Test  
1
2
3
Total  
Pulse Output  
Totalizer Control  
DEVICE INFO  
1
2
3
Poll Address  
Num Req Preams  
Burst Mode  
3-29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 9701 Mass Flowmeter  
1
2
VIEW FIELD  
DEVICE  
1
2
3
4
Flow  
1
PROCESS  
VARIABLES  
Temperature  
Total  
VARIABLES  
Density  
1
2
3
4
5
6
7
Flow  
Flow Range  
1
Total Secondary  
Variable  
VIEW OUTPUT  
VARIABLES  
Percent Range  
Analog Value  
VIEW SECONDARY VARIABLE  
VIEW TERTIARY VARIABLE  
VIEW QUATERNARY VARIABLE  
1
2
Total Tertiary Variable  
Pres Freq  
3
View Status  
1
Quaternary Variable  
Dens  
1
2
Total  
Reset Totalizer  
4
TOTALIZER  
CONTROL  
1
2
View Status  
Self Test  
1
2
3
4
TEST/STATUS  
LOOP TEST  
2
DIAGNOSTICS  
AND SERVICE  
1
2
Fix Analog Output  
Fix Frequency Output  
1
2
3
PERFORM CALIBRATION  
Flow  
Zero Value  
PERFOMR AUTO  
ZERO  
Trim Analog Output  
1
2
3
4
5
Tag  
PV Unit  
3
BASIC SETUP  
Analog Range Values  
Frequency Factor  
Rate Factor  
1 CHARACTERIZE  
SENSOR  
1
2
Flow Calibration Number  
Density Calibration Factor  
1
2
3
4
Flow Unit  
1
FLOW  
Flow Cutoff  
Flow Direction  
Flow Damp  
2
CONFIGURE  
FIELD DEVICE  
VARIABLES  
1
2
3
Density Unit  
Slug Low Limit  
Slug High Limit  
2
DENSITY  
3
Temperature Unit  
4
DETAILED  
SETUP  
1
2
3
Range Values  
Fix Analog Output  
Trim Analog Output  
1
ANALOG  
OUTPUT  
1
2
3
Frequency Factor  
Rate Factor  
3
4
CONFIGURE  
OUTPUTS  
2
3
FREQUENCY  
OUTPUT  
Fix Frequency Output  
1
2
Poll Address  
Number of Request Preambles  
HART OUTPUT  
5
REVIEW  
DEVICE  
INFORMATION  
3-30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Micro  
Motion  
Model 9712 Mass Flowmeter  
1
2
3
4
Flow  
1
PROCESS  
VARIABLES  
1
2
VIEW FIELD  
DEVICE  
Temperature  
Total  
VARIABLES  
Density  
1
2
3
4
5
6
7
Primary Variable is  
Primary Variable  
1
2
Secondary Variable is  
Secondary Variable  
PV Percent Range  
VIEW OUTPUT  
VARIABLES  
PV Analog Output  
VIEW SECONDARY VARIABLE  
VIEW TERTIARY VARIABLE  
VIEW QUATERNARY VARIABLE  
1
2
Tertiary Variable is  
Tertiary Variable  
3
View Status  
1
2
Quaternary Variable is  
Quaternary Variable  
1
2
3
4
Total  
Start Totalizer  
Stop Totalizer  
Reset Totalizer  
4
TOTALIZER  
CONTROL  
1
View Status  
Self Test  
1
2
3
4
TEST/STATUS  
LOOP TEST  
2
1
2
Fix Analog Output  
Fix Frequency Output  
2
DIAGNOSTICS  
AND SERVICE  
1
2
Perform Calibration  
Flow  
1
2
3
PERFORM AUTO ZERO  
DENSITY POINT 1 (AIR)  
DENSITY POINT 2 (WATER)  
CALIBRATION  
Trim Analog Output  
1
2
Perform Calibration  
Density  
1
2
Perform Calibration  
Density  
1
2
3
4
5
Tag  
PV Unit  
Analog Range Values  
Frequency Factor  
Rate Factor  
3
BASIC SETUP  
1
CHARACTERIZE  
SENSOR  
1
2
Flow Calibration Number  
Density Calibration Factor  
1
2
3
Flow Unit  
1
2
3
4
5
Base Flow Unit  
Base Time Unit  
Flow Conversion Factor  
Flow Text  
1
FLOW  
Flow Cutoff  
CONFIGURE  
SPECIAL UNITS  
Flow Direction  
Flow Damp  
2
CONFIGURE  
FIELD DEVICE  
VARIABLES  
4
5
Total Text  
1
2
3
Density Unit  
Slug Low Limit  
Slug High Limit  
2
DENSITY  
3
Temperature Unit  
4
DETAILED  
SETUP  
1
2
3
4
5
Primary Variable is  
Range Values  
1
ANALOG  
OUTPUT  
PV Analog Output Cutoff  
Fix Analog Output  
Trim Analog Output  
3
CONFIGURE  
OUTPUTS  
1
Frequency Factor  
Rate Factor  
2
3
FREQUENCY  
OUTPUT  
2
3
Fix Frequency Output  
1
2
3
4
Poll Address  
Number of Request Preambles  
Burst Mode  
HART OUTPUT  
Burst Option  
4
DEVICE  
INFORMATION  
5
REVIEW  
3-31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 9739 Mass Flowmeter  
1
2
3
4
5
Mass Flow  
Temperature  
Mass Total  
Density  
6
7
8
9
Volume Flow  
Volume Total  
Volume Inventory  
Viscosity  
1
PROCESS  
VARIABLES  
1
2
VIEW FIELD  
DEVICE  
VARIABLES  
Mass Inventory  
Pressure  
1
2
3
4
5
6
VIEW PRIMARY VARIABLE  
VIEW SECONDARY VARIABLE  
VIEW TERTIARY VARIABLE  
VIEW QUATERNARY VARIABLE  
VIEW EVENT 1  
VIEW OUTPUT  
VARIABLES  
VIEW EVENT 2  
3
View Status  
1
2
3
4
5
Mass Total  
Volume Total  
Start Totalizer  
Stop Totalizer  
Reset Totalizer  
4
TOTALIZER  
CONTROL  
1
2
View Status  
Self Test  
1
2
3
TEST/STATUS  
LOOP TEST  
1
2
3
4
Perform Auto Zero  
Mass Flow  
Zero Time  
1
2
3
Fix Analog Output 1  
Fix Analog Output 2  
Fix Frequency Output  
Convergence Limit  
2
DIAGNOSTICS  
AND SERVICE  
1
2
3
DENSITY 1 (AIR)  
DENSITY 2 (WATER)  
DENSITY 3 (FLOW)  
CALIBRATION  
1
2
AUTO ZERO  
DENSITY CALIBRATION  
1
2
VISCOSITY SLOPE  
CALIBRATION  
VISCOSITY OFFSET  
CALIBRATION  
4
5
Trim Analog Output 1  
Trim Analog Output 2  
3
4
VISCOSITY CALIBRATION  
TEMPERATURE CALIBRATION  
1
2
3
4
Tag  
5
6
7
Analog 2 Range Values  
TV Frequency Factor  
TV Rate Factor  
Primary Variable Unit  
1
2
TEMPERATURE  
Analog 1 Range Values  
Secondary Variable Unit  
3
BASIC SETUP  
OFFSET CALIBRATION  
TEMPERATURE SLOPE  
CALIBRATION  
1 CHARACTERIZE  
SENSOR  
1
2
3
4
5
Flow Calibration Number  
DENSITY  
Temperature Calibration  
VISCOSITY  
PRESSURE COMPENSATION  
1
2
3
Base Mass Unit  
Base Mass Time  
Mass Flow  
Conversion Factor  
Mass Flow Text  
Mass Total Text  
1
2
3
4
5
6
7
8
Mass Flow Unit  
Mass Flow Cutoff  
1
FLOW  
SPECIAL MASS UNITS  
Volume Flow Unit  
Volume Flow Cutoff  
SPECIAL VOLUME UNITS  
Flow Direction  
4
5
1
2
3
Base Volume Unit  
Base Volume Time  
Volume Flow  
Flow Damp  
2
CONFIGURE  
FIELD DEVICE  
VARIABLES  
Conversion Factor  
Volume Flow Text  
Volume Total Text  
1
Density Unit  
4
5
2
DENSITY  
2
3
4
Density Damp  
Slug Low Limit  
Slug High Limit  
4
DETAILED  
SETUP  
1
2
Temperature Unit  
3
4
TEMPERATURE  
Temperature Damp  
VISCOSITY/  
PRESSURE  
1
2
DP Unit  
Viscosity Unit  
1
2
3
4
5
6
ANALOG OUTPUT 1  
ANALOG OUTPUT 2  
FREQUENCY OUTPUT  
Control Output  
3
4
5
CONFIGURE  
OUTPUTS  
FAULT OUTPUT  
DEVICE  
INFORMATION  
HART OUTPUT  
1
2
EVENT 1  
EVENT 2  
CONFIGURE  
EVENTS  
5
REVIEW  
3-32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model APEX Radar Level Gauge  
1 Variable re-map  
2 PV is  
3 SV is  
4 TV is  
5 4V is  
1 VARIABLE  
MAPPING  
2 level  
3 PV % rnge  
4 AO1  
1 PROCESS  
VARIABLES  
5 dist  
6 vol  
7 intTemp  
8 temp  
9 RTD  
10 stVol  
11 loop vlt  
12 SNR  
13 TargStr  
1 STATUS  
1 TEST DEVICE  
2 Loop test  
3 D/A trim  
2 Master reset  
2 DIAG/  
SERVICE  
1 LevUnits  
2 VolUnits  
3 TmpUnits  
1 Distributor  
2 Model  
3 Dev id  
4 Tag  
5 Date  
1 Tag  
2 TRANSMITTER  
UNITS  
3 BASIC  
SETUP  
1 Apply  
values  
2 Range  
values  
3 RERANGING  
4 GaugeHt  
5 RTD usage  
6 EmpTank  
6 Write protect  
7 Descriptor  
8 Message  
9 REVSIONS #'S  
10 CONSTRUCTION  
MATLS  
1 Flange  
Type  
2 Matrl  
3 Meter  
4 Antenna  
5 Barrier  
1 DEVICE  
SETUP  
2 PV  
3 PV AO  
4 PV LRV  
5 PV URV  
3 PV % rnge  
1 DEVICE  
INFORMATION  
1 Line 1  
2 LINE 2  
3 Lang  
1 Current  
2 PctRange  
3 Level  
2 LCD DISPLAY  
4 DETAILED  
SETUP  
4 Distance  
5 Volume  
6 Int Temp  
7 Temp  
8 RTD Ohms  
9 Std Vol  
10 Loop Vlt  
11 SNR  
1 Tnktyp  
2 Diametr  
3 LthOrHt  
4 STRAPPING  
TABLE  
5 VOLUME  
COEFFIC  
3 VOLUME  
GEOMETRY  
1 PV LRV  
2 PV URV  
3 PV % rnge  
4 Damp  
5 UprNlZ  
6 LowNlZ  
4 SIGNAL  
CONDITION  
12 TargStr  
1 ANALOG  
OUTPUT  
2 HART  
5 OUTPUT  
CONDITION  
OUTPUT  
1 LEVEL  
2 DISTANCE  
3 VOLUME  
1 Threshold Units  
2 Threshold Range  
3 Threshold snapshot  
6 THRESHOLD  
SETTING  
4 INTERNAL TEMP  
5 TEMPERATURE  
6 RTD OHMS  
7 STANDARD  
VOLUME  
8 LOOP VOLTAGE  
9 SIGNAL/NOISE  
RATIO  
1 DYNAMIC  
VARIABLES  
5 REVIEW  
MENUS  
2 TRANSMITTER  
VARS  
3 OTHER  
VARIABLES  
10 TARGET  
STRENGTH  
3-33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TM  
Model ProBar DP Flowmeter  
1 Flo Pres  
1 Self test  
2 % rnge  
2 STATUS  
3 AO  
4 Pres  
5 Snsr temp  
1 PROCESS  
VARIABLES  
1 Keypad input  
2 Apply values  
1 RE-RANGE  
2 ANALOG  
OUTPUT TRIM  
1 D/A trim  
2 Scaled D/A trim  
1 TEST DEVICE  
2 Loop test  
3 CALIBRATION  
2 DIAG/  
SERVICE  
3 SENSOR TRIM  
4 Recall fact trim  
1 Zero trim  
2 Lower sensor trim  
3 Upper sensor trim  
4 SENSOR TRIM  
POINTS  
1 Tag  
2 Unit  
1 Keypad input  
2 Apply values  
3 RANGE  
VALUES  
3 BASIC  
SETUP  
1 Sel dec pt pos  
2 CM Upper Value  
3 CM Lower Value  
4 CM Units  
1 Date  
4 DEVICE  
INFORMATION  
5 Transfer  
function  
6 Damping  
7 METER  
2 Descriptor  
3 Message  
4 Write protect  
5 Cm xf fnct  
1 Meter type  
2 CM SETUP  
1 PROCESS  
VARIABLES  
2 SENSOR TRIM  
3 Recall fact trim  
4 Unit  
OPTIONS  
1 DEVICE  
SETUP  
2 PV  
1 PRESSURE  
SENSOR  
3 AO  
1 SENSORS  
4 LRV  
5 URV  
2 TEMPERATURE  
SENSOR  
1 Snsr temp  
2 Snsr temp unit  
4 DETAILED  
SETUP  
1 PROCESS  
VARIABLES  
1 Flo Pres  
2 % rnge  
3 Pres  
2 SIGNAL  
CONDITION  
4 Snsr temp  
1 Keypad input  
2 Apply values  
2 RANGE VALUES  
3 Unit  
4 Transfer  
function  
1 High Alarm  
2 Low Alarm  
3 High Sat  
4 Low Sat  
5 AO Alrm typ  
6 Alarm/Sat type  
5 Damping  
6 Snsr temp unit  
7 ALARM/SAT  
LEVELS  
1 PROCESS  
VARIABLES  
2 ANALOG  
OUTPUT  
3 HART OUTPUT  
4 METER  
1 Flo Pres  
2 % rnge  
3 AO  
4 Pres  
5 Snsr temp  
3 OUTPUT  
CONDITION  
OPTIONS  
1 FIELD DEVICE INFO  
2 SENSOR  
4 DEVICE  
INFORMATION  
INFORMATION  
3 Self test  
4 DIAPHRAM SEAL  
INFO  
5 REVIEW  
3-34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TM  
Model ProBar UC Flowmeter  
1 Flo Pres  
2 % range  
3 AO  
4 Pres  
1 Self test  
2 STATUS  
1 TEST DEVICE  
2 Loop test  
1 PROCESS  
VARIABLES  
1 Keypad input  
2 Apply values  
1 RE-RANGE  
5 Snsr temp  
1 D/A trim  
2 Scaled D/A  
trim  
2 DIAG/  
SERVICE  
2 ANALOG  
OUTPUT TRIM  
3 CALIBRATION  
1 Zero trim  
2 Lower sensor  
trim  
3 Upper sensor  
trim  
1 Tag  
2 Unit  
3 SENSOR  
TRIM  
4 Recall fact  
trim  
1 Keypad input  
2 Apply values  
3 BASIC  
SETUP  
3 RANGE  
VALUES  
4 DEVICE  
INFORMATION  
5 Transfer  
function  
6 Damping  
7 METER  
OPTIONS  
1 Date  
4 SENSOR  
TRIM POINTS  
2 Descriptor  
3 Message  
4 Write protect  
1
2
4
5
6
Sel dec pt pos  
CM Upper Value  
CM lower Value  
CM Units  
1
2
3
4
PROCESS  
VARIABLES  
SENSOR  
TRIM  
Recall fact  
trim  
1 Meter type  
2 CM SETUP  
CM xf fnct  
1 PRESSURE  
SENSOR  
Unit  
1 SENSORS  
1 Snsr temp  
2 Snsr temp  
unit  
2 TEMPERATURE  
SENSOR  
1 DEVICE  
SETUP  
2 PV  
1 PROCESS  
VARIABLES  
2 RANGE  
VALUES  
3 AO  
4 LRV  
5 URV  
1 Flo Pres  
2 % rnge  
3 Pres  
1 Keypad input  
2 Apply values  
4 Snsr temp  
2 SIGNAL  
3 Unit  
CONDITION  
4 Transfer  
function  
1 High Alarm  
2 Low Alarm  
3 High Sat  
4 Low Sat  
5 AO Alrm typ  
6 Alarm/Sat Type  
4 DETAILED  
SETUP  
5 Damping  
6 Snsr temp  
unit  
7 ALARM/SAT  
LEVELS  
1
2
3
4
5
Flo Pres  
% range  
AO  
Pres  
Snsr  
1 PROCESS  
VARIABLES  
1 Loop test  
2 D/A trim  
3 Scaled D/A  
trim  
3 OUTPUT  
CONDITION  
2 ANALOG  
OUTPUT  
temp  
1 Poll addr  
2 Num req  
preams  
3 Burst  
mode  
4 AO Alrm typ  
3 HART  
OUTPUT  
1 Meter type  
2 CM SETUP  
3 CMV  
4 METER  
OPTIONS  
4 Burst  
option  
1 FIELD  
DEVICE INFO  
1 Meas type  
2 Module config type  
3 Isoltr matl  
4 Fill fluid  
2 SENSOR  
INFORMATION  
4 DEVICE  
INFORMATION  
5 Process Connector  
6 Process Conn Matl  
7 O ring matl  
3 Self test  
4 DIAPHRAM  
SEAL INFO  
5 REVIEW  
8 Drain vent matl  
3-35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model Tri-20/9000 Oval Flowmeter  
1 PV  
2 % rnge  
3 SV  
4 TV  
1 PROCESS  
VARIABLES  
5 QV  
6 Variable mapping  
7 Variable Re-Map  
1 Alrm  
1 Alarm Status 1  
2 Alarm Status 2  
3 Diagnostic Status  
2 Reset Alarm  
3 STATUS  
4 Seq No  
2 DIAGS &  
SERVICES  
5 Vcf  
1 Loop Test  
6 Meter Freq  
8 Int Temp  
9 TEST DEVICE  
2 CONTACT O/P  
3 Pulse O/P Test  
4 Warning Level  
1 Tag  
1 K-Fact  
2 Unit  
3 I/P Func  
4 Cutoff  
2 METER  
CONFIG  
1 DEVICE  
SETUP  
2 PV  
1 MFFR unit  
2 METER FACTORS  
3 METER  
CALIBRATION  
3 BASIC  
SETUP  
3 AO  
4 URV  
5 LRV  
1 AO  
2 % rnge  
3 URV  
1 Unit  
2 Refer  
3 Obsvd  
4 DENSITY  
4 LRV  
5 ANALOG  
OUTPUT  
5 Damp  
6 AO Alrm typ  
1 FLOW  
2 TEMPERATURE  
3 DENSITY  
1 MEASUREMENTS  
4 DETAILED  
SETUP  
4 PRESSURE  
1 CORRECTIONS  
2 TOTALIZERS  
2 COMPUTATIONS  
3 OUTPUTS  
1 ANALOG  
OUTPUT  
2 CONTACT  
OUTPUT  
3 PULSE O/P 1  
4 PULSE O/P 2  
5 LOCAL DISPLAY  
6 HART OUTPUT  
1 Tag  
2 Descriptor  
3 Message  
4 Date  
5 Model  
1 Alrm:  
6 Ser No  
2 Reset Alarm  
3 STATUS  
7 Manufacturer  
8 Dev id  
4 ALARMS  
4 ALARM CONFIG  
9 REVISION INFO  
10 FLOW METER  
11 PULSER  
12 TEMP SENSOR  
13 ACCESSORIES  
14 W & M  
5 DEVICE INFO  
3-36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model WC3000 Oxygen Analyzer  
1
2
3
4
5
O2  
1
PROCESS  
VARIABLE  
1
VIEW FIELD  
DEVICE  
Eff Value  
Stack Temp  
02 cell  
VARIABLES  
1
2
3
4
PV is  
CJ Temp  
02  
% Range  
02 Output  
1
VIEW PV-  
AOUT  
2
3
VIEW OUTPUT  
VARIABLES  
1
2
SV is  
SV  
2
VIEW SV  
1
2
3
4
02 Cell  
Cell TC  
Stack TC  
CJ mV  
VIEW FIELD  
DEV MV  
1
2
3
4
Start 02 Cal  
Cal Mode  
OPtrakTG?  
Cal State  
1
2
3
4
Status Grps 1 to 6  
Operate Mode  
A/O Saturated  
A/O fixed  
1
2
3
STATUS  
2
DIAGNOS  
AND  
SERVICE  
Loop Test  
1
2
3
4
Cal State  
TimeRemain  
Present TG  
Present 02  
1
2
3
4
PERFORM 02 CAL  
02 CAL STATUS  
LAST CALCNST  
Rest CAlConstant  
02 CALIBRATION  
1
2
3
Cal Slope  
Cal Const  
Cell Res  
4
Trim Analog Output  
1
2
PV is  
SV is  
1
2
3
4
5
Tag  
1
2
3
4
5
6
7
Norm URV  
Norm LRV  
02 Rnge Mode  
HiRngInCal  
RngSwtSP  
Hi.rng.URV  
Hi.rng.LRV  
ASSIGN PV & SV  
SELECT 02 RANGE  
SEL 02 XFER FN  
3
BASIC  
SETUP  
1
Dev id  
2
3
4
5
6
Descriptor  
Message  
Date  
DEVICE INFORMATION  
Final Assm  
Snsr s/n  
1
SENSORS  
1
2
3
4
5
02  
EFFICIENCY  
STACK TEMP  
02 CELL TEMP  
COLD JUNC  
TEMP  
1
2
3
4
5
Value  
Unit  
USL  
1
2
3
4
URV  
LRV  
Xfer Funct  
% Range  
LSL  
Min Span  
6
7
8
9
02 CELL MV  
02 CELL TC MV  
STACK TC MV  
COLD JUNC MV  
2
SIGNAL  
CONDITION  
1
2
3
4
02 Out Put  
A/O Alrm type  
Loop Test  
1
ANALOG OUTPUT  
HART OUTPUT  
1
2
Poll Addr  
D/A Trim  
2
3
3
4
OUTPUT  
4
DETAILED  
SETUP  
# Req Preams  
RELAYS OUTPUT  
CONDITION  
1
K1  
K2  
2
1
2
3
Slope  
Constant  
Heater SP  
1
2
02  
CALCULATE  
EFFICIENCY  
1
2
3
Eff. Enable  
K1 Eff  
K2 Eff, etc.  
1
High TG  
Low TG  
2
3
4
5
6
7
8
9
Cal Mode  
OPtrakTG  
Cal Intrvl  
NxtCalTime  
TG Time  
Purg Time  
Res AlrSP  
5
6
02 CALIB  
1
2
3
High Alm SP  
Lo Alrm SP  
Deadband  
5
REVIEW  
02 ALARMS  
3-37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX A  
HART Communicator Messages  
The following is a list of messages used by the HART Communicator (HC)  
with their corresponding descriptions.  
• Variable parameters within the text of a message are indicated with  
<variable parameter>.  
• Reference to the name of another message is identified by  
[another message].  
Message  
Description  
Add item for ALL  
device types or only  
for this ONE device  
type.  
Asks the user whether the Hot Key item being added  
should be added for all device types or only for the type of  
device that is connected.  
All variables  
associated with this  
variable must be  
This occurs if you marked one or more earlier variables and  
try to leave the current one unmarked.  
marked or not marked If you answer “Yes”, then earlier variables will be marked or  
the same.  
umarked the same as the current variable.  
Command Not  
Implemented  
The connected device does not support this function.  
Comm error  
HC cannot understand the response from the device.  
associated with host  
comm port  
Comm error  
associated with field  
device comm port  
The device sends back a response indicating the message  
it received was unintelligible.  
Compacting Memory.  
May require up to  
<nbr> minutes to  
complete.  
When electrically erasable (EE) memory becomes  
fragmented, the empty spaces are gathered to form one  
large empty space so that a configuration can be stored.  
This takes time.  
Compare: List of  
marked variables are  
not the same.  
Results of compare function.  
Configuration  
memory not  
The configuration stored in memory is incompatible with the  
device to which a transfer has been requested.  
compatible with  
connected device  
Device Busy  
The connected device is busy performing another task.  
A-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Message  
Description  
Device Disconnected  
Device fails to respond to a command.  
Device write protected Device is in write-protect mode. Data can not be written.  
Device write Device is in write-protect mode. Press YES to turn the HC  
protected. Do you still off and lose the unsent data.  
want to shut off?  
Display value of  
variable on Hotkey  
menu?  
Asks whether the value of the variable should be displayed  
adjacent to its label on the Hotkey menu if the item being  
added to the Hotkey menu is a variable.  
Download data from  
Prompts user to press SEND softkey to initiate a memory to  
configuration memory device transfer.  
to device  
Exceed field width  
Indicates field width for the current arithmetic variable  
exceeds that specified in the device description edit format.  
Exceed precision  
Indicates precision for the current arithmetic variable  
exceeds that specified in the device description edit format.  
Ignore next 50  
occurrences of  
status?  
Asked after displaying device status. Softkey answer  
determines whether next 50 occurrences of device status  
will be ignored or displayed.  
Illegal character  
Illegal date  
An invalid character for the variable type was entered.  
The day portion of the date is invalid.  
Illegal month  
The month portion of the date is invalid.  
The year portion of the date is invalid.  
Illegal year  
Incomplete exponent  
The exponent of a scientific notation floating point variable  
is incomplete.  
Incomplete field  
The value entered is not complete for the variable type.  
Insufficient space to  
store configuration  
The Memory Module or data pack does not have enough  
memory to store the new configuration.  
Looking for a device  
Polling for multidropped devices at addresses 1–15.  
Mark as read only  
variable on Hot key  
menu?  
Asks whether the user should be allowed to edit the  
variable from the Hot key menu if the item being added to  
the Hot key menu is a variable.  
No device  
configuration in  
configuration memory  
There is no configuration saved in memory available to re-  
configure off-line or transfer to a device.  
A-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Message  
Description  
No device description Due to a stored configuration created in the presence of a  
for configuration in  
offline storage  
DD not now available.  
No device description The Communicator has not been programmed with a  
for device at address  
<nbr>.  
device description that it can use to communicate with the  
device it found at the indicated polling address. The device  
information (manufacturer ID, device ID, device revision) is  
also displayed.  
No Device Found  
Poll of address zero fails to find a device, or poll of all  
addresses fails to find a device if auto-poll is enabled.  
No Device found at  
address 0. Poll?  
The polling option is set to ask before polling.  
No Hotkey menu  
available for this  
device.  
There is no menu named “Hotkey” defined in the device  
description for this device.  
No offline devices  
available.  
There are no device descriptions available to be used to  
configure a device offline.  
No online device  
connected. Do you  
still want to turn off?  
Communicator is set up to send configuration to online  
device. The device is not connected and you pressed off  
key before sending. You are being asked if OK to turn off.  
No simulation devices There are no device descriptions available to simulate a  
available.  
device.  
No  
There is no menu named “upload_variables” defined in the  
UPLOAD_VARIABLES device description for this device. This menu is required for  
in ddl for this device  
offline configuration.  
No Valid Items  
The selected menu or edit display contains no valid items.  
NOTICE: There are  
dependent variables  
for this unit variable.  
When marking offline variables, there are other variables  
that depend on this variable.  
NOTICE: Unit relation  
variables will also be  
unmarked.  
If the unit variable is marked then unmark the relation  
variable. The unit will be unmarked automatically.  
NOTICE: The unit  
variable for this  
variable is unmarked.  
The variable is marked as part of a relation and the unit is  
not yet marked. That is, the range may be sent to a device  
with units that are not the same as what is stored offline.  
NOTICE: Upgrade 275 You have connected to a device that is a newer revision  
software to access  
new connected device  
functions. Continue  
with old description?  
than what is linked into the HC.  
A-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Message  
Description  
OFF KEY DISABLED  
Appears when the user attempts to turn the HC off before  
sending modified data or before completing a method.  
Online device  
There is unsent data for a previously connected device.  
Press RETRY to send data, or press OK to disconnect and  
lose unsent data.  
disconnected with  
unsent data. RETRY  
or OK to lose data.  
Out of memory for  
There is no more memory available to store additional Hot  
Hotkey configuration. Key items. Unnecessary items should be deleted to make  
Delete unnecessary  
items.  
space available.  
Overwrite existing  
Requests permission to overwrite existing configuration  
configuration memory either by a device-to-memory transfer or by an offline  
configuration. User answers using the softkeys.  
Press OK...  
Press the OK softkey. This message usually appears after  
an error message from the application or as a result of  
HART communications.  
Restore device value? The edited value that was sent to a device was not properly  
implemented. Restoring the device value returns the  
variable to its original value.  
Save data from device Prompts user to press SAVE softkey to initiate a device-to-  
to configuration  
memory  
memory transfer.  
Saving data to  
configuration  
memory.  
Data is being transferred from a device to configuration  
memory.  
Sending data to  
device.  
Data is being transferred from configuration memory to a  
device.  
All variables  
associated with this  
variable must be  
This occurs if you marked one or more earlier associated  
variables and try to leave the current one unmarked, or if  
you unmarked one or more earlier associated variables and  
marked or not marked try to leave the current one marked.  
the same. Change  
others?  
If you answer “Yes” then earlier variables will be marked or  
umarked the same as the current variable.  
Sort allows you to  
group and display  
configurations by  
their Descriptor, Tag,  
or Name.  
Allows you to customize your menu displays with the sort  
option. It is accessed through Saved Configurations and  
operates in conjunction with the Filter option.  
A-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Message  
Description  
Specified filter passes The filter automatically reset to all ‘*’. This is due to being  
no configurations.  
Filter reset to ‘*’  
too restrictive while filtering a table of contents.  
Storage location write The rated life of the EEPROM could be used up. Contact  
protected your service representative.  
Some variables in this This configuration contains write-only variables which  
saved configuration  
were not marked  
because they were  
not read.  
cannot be read. The user must mark and edit these  
variables before they will be sent down to a device.  
There is unsent data.  
Send it before  
Press YES to send unsent data and turn the HC off. Press  
NO to turn the HC off and lose the unsent data.  
shutting off?  
Too few data bytes  
received.  
Command returns fewer data bytes than expected as  
determined by the device description.  
Field Device Fault.  
Device returns a command response indicating a fault with  
the connected device.  
Units for <variable  
label> has changed.  
Unit must be sent  
before editing, or  
invalid data will be  
sent.  
The engineering units for this variable have been edited.  
Send engineering units to the device before editing this  
variable.  
Unsent data to online  
device. SEND or  
LOSE data.  
There is unsent data for a previously connected device  
which must be sent or thrown away before connecting to  
another device.  
Use up/down arrows  
to change contrast.  
Press DONE when  
done.  
Gives direction to change the contrast of the HC display.  
Value out of range  
The user-entered value is either not within the range for the  
given type and size of variable or not within the min/max  
specified by the device.  
<message> occurred  
reading/writing  
<variable label>  
Either a read/write command indicates too few data bytes  
received, transmitter fault, invalid response code, invalid  
response command, invalid reply data field, or failed pre- or  
post-read method; or a response code of any class other  
than SUCCESS is returned reading a particular variable.  
A-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Message  
Description  
<variable label> has  
an unknown value.  
Unit must be sent  
before editing, or  
invalid data will be  
sent.  
A variable related to this variable has been edited. Send  
related variable to the device before editing this variable.  
A-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX B  
Specifications and Ordering Information  
FUNCTIONAL SPECIFICATIONS  
Memory  
Nonvolatile memory retains contents when the HART Communicator is not  
powered.  
Program and Device Descriptions:  
12 MB (standard)  
4 MB (optional)  
2 KB  
Field Device Data:  
data pack 100 (optional):  
32 KB removable nonvolatile  
memory  
Power Supply  
Five AA 1.5 V batteries (rechargeable NiCad battery pack optional).  
Battery Charger Options  
110/120 V ac, 50/60 Hz, U.S. plug  
220/230 V ac, 50 Hz, European plug  
220/230 V ac, 50 Hz, U.K. plug  
Microprocessors  
32-bit Motorola type 68331  
16-bit Motorola type 68HC705  
Connections  
Battery charger:  
Leadset:  
Memory Module:  
Serial port:  
2.5 mm jack  
Two 4 mm banana plugs  
26 pin, 0.1-in. Berg connector  
PC connected through  
optional PC Communication  
Adapter  
B-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
PERFORMANCE SPECIFICATIONS  
Electromagnetic Compatibility (EMC)  
EMC compliant only when the CE mark appears on both the keypad  
assembly and Memory Module.  
Humidity Limits  
Operates in 0–95% relative humidity under noncondensing conditions  
over the entire operating range of 32 to 122 °F (0 to 50 °C).  
Hazardous Locations Certifications  
CENELEC—Intrinsic Safety Certification  
Factory Mutual (FM)—Intrinsic Safety Approval  
Canadian Standards Association (CSA)—Intrinsic Safety Approval  
ISO 9001 Approval  
The Model 275 HART Communicator is built by an ISO 9001 approved  
system.  
Operating Limits  
32 to 122 °F (0 to 50 °C).  
Storage Limits  
–4 to 158 °F (–20 to 70 °C).  
PHYSICAL SPECIFICATIONS  
Display  
8-line liquid crystal display with 21-character line width (128 by 64 pixels).  
Keypad  
25 large keys including six Action keys, a complete alphanumeric keypad,  
four software-defined function keys, ON/OFF, and cursor control keys;  
membrane design with tactile feedback.  
Weight  
Approximately 3 lb. (1.4 kg) with NiCad battery pack.  
B-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
ORDERING INFORMATION  
The following table lists standard and optional product selections.  
Model  
275  
Product Description  
HART Communicator*  
Battery Pack Option  
Code  
D
R
Battery Holder for Disposable AA Batteries  
Rechargeable NiCad Battery Pack  
Code  
Recharger Service and Plug Type  
1
2
3
9
100/120 V ac, 50/60 Hz, U.S. Plug  
220/230 V ac, European Plug  
220/230 V ac, U.K. Plug  
None  
Code  
Language  
E
F
G
J
English  
French  
German  
Japanese  
Code  
Hazardous Locations Certifications  
I0  
No Approval  
British Approvals Service for Electrical Equipment in Flammable  
Atmospheres (BASEEFA)/CENELEC Intrinsic Safety Certification  
I1  
I5  
I6  
Factory Mutual (FM) Intrinsic Safety Approval  
Canadian Standards Association (CSA) Intrinsic Safety Approval  
Code  
Memory Module Type  
B
D
4 MB Memory Module  
12 MB Memory Module (Standard)  
Code  
00  
Device Description Options  
Standard Factory Loading  
Future Option  
Code  
D1  
D2  
00  
Shipped with one (1) data pack 100 installed  
Shipped with two (2) data pack 100’s  
Shipped without data pack 100  
Typical Model Number: 275 D 9 E I5 D 00 00  
*Typical Model 275 D 9 E I5 D 00 00 includes HART Communicator, AA  
battery pack with batteries, leadset with MINI GRABBERs™ and alligator  
clips, carrying case, FM Intrinsic Safety Approval, and pocket-sized  
instruction manual.  
Options include: NiCad battery pack with recharger, language, certifications,  
and data pack 100. If the NiCad battery pack is selected, one spare battery  
pack per HART Communicator is recommended.  
B-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Spare Parts  
Refer to the following table and exploded view to choose spare parts and  
accessories for the HART Communicator.  
Part Number  
00275-0170-0100  
00275-0170-0101  
00275-0170-0102  
00275-0170-0103  
00275-0171-0100  
00275-0171-0101  
00275-0171-0102  
00275-0171-0103  
00275-0007-0001  
00275-0007-0002  
00275-0007-0003  
00275-0003-0300  
00275-0003-0700  
00275-0006-0100  
00275-0095-0001  
00275-0094-0001  
00275-0013-0001  
00275-0096-0001  
00275-0093-0001  
00275-0100-0001  
00275-8026-0002  
00275-8072-0001  
Description  
AA Alkaline Battery Pack for Code I0  
AA Alkaline Battery Pack for Code I1  
AA Alkaline Battery Pack for Code I5  
AA Alkaline Battery Pack for Code I6  
NiCad Battery Pack for Code I0  
NiCad Battery Pack for Code I1  
NiCad Battery Pack for Code I5  
NiCad Battery Pack for Code I6  
Recharger 220/230 V ac (U.K. plug)  
Recharger 220/230 V ac (European plug)  
Recharger 100/120 V ac, 50/60 Hz (U.S. plug)  
Memory Module 4 MB  
Memory Module 12 MB (Standard)  
Fisher-Rosemount data pack 100  
Belt Clip with Screws  
Hanger (mounts on belt clip option)  
PC Communication Adapter(1)  
Ruggedized 250 Ohm Load Resistor  
Lead Set with Connectors  
Carrying Case  
Pocket-size Manual  
PC Cable (DB9 to DB25)(1)  
(1) Requires Asset Management Solutions (AMS) software with 275 Interface  
Kit option.  
B-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
MAN 4275A00  
English  
October 1994  
HART® Communicator  
NOW YOU CAN:  
• Create configurations  
offline  
• Store data safely  
data pack 100:  
Stores up to 100 typical  
device configurations in  
• Transfer data easily  
removable, nonvolatile memory.  
B-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX C  
CSA and FM Intrinsic Safety Approvals  
CANADIAN STANDARDS ASSOCIATION (CSA)  
The 275 is intrinsically safe for use in Class 1, Division 1, Groups A, B, C,  
and D hazardous locations when connected to CSA certified intrinsic safety  
barriers as indicated in the recreated connection diagram drawing displayed  
below.  
Non-Hazardous Area  
Hazardous Area  
I.S.  
Power  
Barrier  
Supply  
_
+
Load  
CSA Certified  
Intrinsically Safe  
Device  
“Ex1a”  
INTRINSICALLY SAFE / SECURITE INTRINSEQUE  
Certified  
intrinsic safety barriers are listed below  
30V Max, 330 Ohms Min  
28V Max, 300 Ohms Min  
22V max, 180 Ohms Min  
DWG No.  
00275-0082  
Rev. A. Sheet 1 of 1  
TITLE: 275 CSA INTRINSICALLY SAFE CONFIGURATION  
C-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
FACTORY MUTUAL (FM)  
The FM entity parameters listed in Table 1 only apply to associated  
apparatus with linear output.  
.
DWG No.  
00275-0081  
Rev. D. Sheet 1 of 2  
Table 1: FM Entity Parameters  
Input Parameters  
Vmax = 30 Vdc  
Imax = 300 mA  
Ci = 0.07 µF  
Class I, Div. 1, Groups A, B, C, D  
VT or Voc of barrier must be < 30 Vdc  
IT or Isc of barrier must be < 300 mA  
CA of barrier must be > 0.07 µF  
LA of barrier must be > 0 mH  
Li = 0 mH  
Output Parameters  
Voc = 1.7 Vdc  
Isc = 32 mA  
N/A  
N/A  
Before connecting the model 275 into the loop, determine the connected  
inductance of the system by adding the Li of the transmitter and cable.  
The sum must be less than the La, as determined from Table 2, before the  
275 can be connected into the loop.  
If the connected inductance is greater than the value determined from the  
table, a barrier with a lower Isc must be chosen.  
Table 2: Maximum Allowable Connected Inductance  
Im  
La (mH)  
Group  
C
Groups  
A & B  
0.20  
Group  
D
(mA)  
300  
280  
270  
260  
250  
240  
220  
200  
180  
1.80  
2.00  
2.20  
2.50  
2.70  
3.00  
3.20  
4.00  
5.00  
3.20  
3.70  
3.90  
4.30  
4.60  
5.00  
5.90  
7.20  
8.80  
0.21  
0.23  
0.25  
0.27  
0.30  
0.40  
0.50  
0.60  
C-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Table 2: Maximum Allowable Connected Inductance  
Im  
La (mH)  
GROUP  
C
GROUPS  
A & B  
0.80  
GROUP  
D
(mA)  
170  
160  
150  
140  
130  
120  
110  
100  
90  
5.50  
9.90  
11.20  
1.00  
6.20  
1.30  
7.00  
12.70  
14.60  
16.90  
19.80  
23.60  
28.50  
35.10  
39.30  
44.40  
50.50  
57.90  
67.10  
73.70  
78.70  
87.10  
93.50  
113.10  
139.40  
176.30  
229.90  
274.80  
312.40  
358.40  
449.00  
530.10  
635.30  
700.00  
1.60  
8.00  
2.00  
9.00  
2.50  
10.00  
12.00  
15.00  
18.00  
20.00  
22.00  
25.00  
28.00  
34.00  
37.00  
40.00  
43.00  
48.00  
56.00  
70.00  
87.00  
110.00  
135.00  
150.00  
170.00  
210.00  
250.00  
300.00  
330.00  
3.00  
4.00  
5.00  
85  
5.50  
80  
6.00  
75  
6.70  
70  
7.50  
65  
8.80  
62  
9.50  
60  
10.00  
11.00  
12.00  
15.00  
19.00  
23.00  
31.00  
36.00  
40.00  
46.00  
58.00  
68.00  
82.00  
90.00  
57  
55  
50  
45  
40  
35  
32  
30  
28  
25  
23  
21  
20  
NOTE: Im = IscBarrier + Isc275 = IscBarrier + 32mA  
DWG No.  
00275-0081  
Rev. D.  
Sheet 1 of 2  
C-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Non-Hazardous Area  
Hazardous Area  
Barrier  
Power  
or  
Supply  
Converter  
_
+
SMART  
Transmitter  
Non-Hazardous Area  
Hazardous Area  
+
Barrier  
or  
_
Power  
Supply  
+
Converter  
System  
V
V
_
SMART  
Transmitter  
DWG No.  
00275-0081  
Rev. D. Sheet 2 of 2  
TITLE: Model 275 FM IS Installation Drawings  
C-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX D  
Troubleshooting Communication Problems  
This section contains troubleshooting steps you can take if you are  
experiencing communications problems between a field device and your  
HART Communicator.  
Problem  
Possible Cause  
Possible Solution  
Intermittent  
communication  
Insufficient loop resistance  
at the HART frequencies.  
Add an additional 250 ohm  
resistor in series in the loop.  
Place the HART Communicator  
leads across the resistor and  
verify if communication has  
been restored.  
Noise on the field loop  
Verify field wiring shield is  
grounded at one end only.  
Normally, the shield is grounded  
at the control system and  
floating at the field device. See  
diagram following this table.  
Noise or signal distortion  
from the control system  
(i.e., noise from power  
supply powering field  
Remove field wiring and power  
loop with external power supply  
and a 250 resistor in the loop.  
Verify if communication is  
devices or front end analog restored with this configuration.  
circuitry inside of control  
system may be distorting  
the HART signal).  
If yes, an oscilloscope may be  
used to inspect possible noise  
or signal distortion from the  
control system. Noise of interest  
would be in the 800 Hz to  
10 KHz range with an amplitude  
of 0.5Vpp or larger. Larger  
amplitudes below 800 Hz or  
above 10 KHz may also affect  
communication.  
Place a 0.1 microfarad (µf) to a  
0.22µf (Capacitor parameters:  
working voltage: 50V DC and no  
polarity) across the control  
system terminals. Verify if  
communication is restored. If  
not, place a 250 ohm resistor in  
series and verify if  
communication is restored. See  
diagram following this table.  
D-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Problem  
Possible Cause  
Possible Solution  
No  
Insufficient loop resistance  
at the HART frequencies.  
Add an additional 250 ohm  
resistor in series in the loop.  
Place the HART Communicator  
leads across the resistor and  
verify if communication has  
been restored.  
communication  
with field device  
Insufficient loop current and Verify that there is at least 4mA  
voltage at the field device  
terminals.  
and 12V DC at the field device  
terminals.  
Field device may be set to  
HART address other than  
zero (multi-drop mode).  
Change 275 mode to digital  
polling.  
Control system is HART communication with  
Stop HART communications on  
communicating  
HART, but the  
275 is not  
the HART Communicator is the control system and verify if  
being prevented by the  
control system  
communication between the  
field devices and HART  
communicating  
properly  
Communicator is restored.  
Battery pack  
Battery pack has been  
Remove battery pack and  
does not accept a discharged past the normal recharge while it is  
charge  
range.  
disconnected from the  
Communicator.  
!
WARNING  
250 ohm  
external  
loop resistor  
Explosions can result in death or  
serious injury. Do not exceed the  
allowed loop capacitance.  
Control System field  
Terminal blocks  
Field  
Device  
+24V DC  
Power  
Shield terminal.  
Floating at  
transmitter end  
0.1uF to  
0.22uF  
External  
Capacitor  
24V DC  
Return  
Field device must  
have 4mA and 12V  
DC at terminals  
250 ohm resistor  
Field  
Control  
System Side  
Device side  
D-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IF YOU ARE STILL HAVING PROBLEMS  
If you have already gone through the Troubleshooting table on the previous  
pages and are still having problems, contact Fisher-Rosemount technical  
support at 1-800-833-8314 or 1-512-832-3774. Please complete the  
following check list and have the following information available.  
Information  
Notes  
Manufacturer and model of the control  
system.  
Manufacturer and model of the field device.  
Loop diagram of the problem loop.  
Plant layout and proximity to other equipment.  
Do HART communications occur when other  
devices or processes are not running?  
Total cable length from the termination panel  
to the field device.  
Message on the Communicator screen when  
attempting to communicate with the field  
device (e.g., device not found).  
Task performed when a specific error  
message was displayed.  
Number of HART loops in the facility.  
Number of HART loops that are failing (i.e., no  
communication).  
For further information on the HART Communicator, contact our web  
address at www.hartcommunicator.com.  
D-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
D-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INDEX  
data pack 100 1-1, B-4  
Device Descriptions 1-12  
Device Setup 1-20, 2-2  
A
Accessories B-4  
Action Keys  
Arrow Keys 1-5, 1-6  
Cursor Keys 1-6  
Hot Key 1-6  
Left Arrow Key 1-6  
On/Off Key 1-5  
Previous Menu Key 1-6  
Right Arrow Key 1-6  
Select Key 1-6  
Up Arrow Key 1-6  
Alphanumeric Keys 1-8  
Always Poll 1-23  
E
EMC Compliance B-2  
AMS Software 1-18, 1-26, 1-27, 1-28, 1-29  
Analog Output (AO) 1-20, 2-3  
Ask before Polling 1-23  
Asset Management Solutions (AMS) 1-26  
Automatic Turn Off 1-24  
F
B
Basic Setup 2-5  
Function Key Lables 1-7  
Function Keys 1-6  
Battery Pack 1-35  
Changing Alkaline Batteries 1-36  
Recharging NiCad Battery Pack 1-37  
C
Calibration 1-35  
CE Approval B-2  
Changing Stored Configurations 1-29  
Communication Adaptor 1-2, 1-27, B-1  
Communication Problems D-1  
Communicator Messages A-1  
Communicator, HART 1-10  
Compare 1-19  
Configuration Parameters 1-20  
Connections  
Connection Diagram 1-2  
G
Generic Online Menu Tree 1-20  
Graphic Symbols 1-10  
H
Hazardous Locations Certifications B-2  
HOME Key 1-7  
Hot Key 1-6  
Customizing the Hot Key Menu 1-31  
Deleting Options 1-33  
Load Resistance 1-4  
Rear Connection Panel 1-2  
Wiring Connections 1-2  
Contrast 1-24  
I
Copy To 1-18  
Icons  
CSA Intrinisc Safety Connection 1-4  
CSA Intrinsic Safety Approvals C-1  
Sofware 1-10  
Ignore Diagnostics 1-25  
Intrinsic Safety Approvals B-3, C-1  
ISO 9001 Approved B-2  
D
Data Entry 1-9  
I-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
K
Keypad  
Action Keys 1-5  
Alphanumeric keys 1-8  
Function Keys 1-6  
Hot Key 1-6  
R
Recharging Batteries 1-37  
Rename 1-19  
Shift Keys 1-9  
L
Language Options B-3  
Liquid Crystal Display 1-4  
Listen for PC 1-17, 1-26  
Load Resistor 1-4, B-4  
S
Lower Range Value (LRV) 1-20, 2-3  
Certifications B-2  
M
Main Menu 1-9, 1-12  
Memory Module 1-37  
Replacing the Memory Module 1-38  
Menu Icons 1-10  
Menu Structure 1-11  
Messages A-1  
Microprocessors B-1  
Model Number B-3  
Model-Specific Routine Tasks 3-1  
N
Never Poll 1-23  
NIST 1-35  
O
Off Key Disabled 1-5  
Offline Configure  
Field Device Revision Menu 1-14  
Manufacturer Menu 1-14, 1-28  
Model Menu 1-14  
Offline Connections 1-9  
Offline Menu  
New and Saved Configurations 1-13  
Offline Menu Tree 1-13  
ON/OFF Key 1-5  
T
Tag 1-5  
Troubleshooting D-1  
U
Unmark All 1-15  
Upgrading Software 1-35  
Upper Range Value (URV) 1-20, 2-3  
Utility Menu 1-22  
Auto Poll 1-22  
Contrast Adjustment 1-24  
Online Connections 1-9  
Online Help 1-6  
Online Menu 1-9  
Ordering Information B-3  
W
Wiring  
Load Resistance 1-4  
P
PC Interface 1-26  
Poll Using Tag 1-23  
Polling 1-23  
Y
Year 2000 Compliance 1-34  
I-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Coleman Indoor Furnishings 2794 490 User Manual
Compaq Stereo System DL580 User Manual
Craftsman Air Compressor 919195411 User Manual
Crate Amplifiers Musical Instrument Amplifier GX 25M User Manual
Crest Audio DJ Equipment X 18R User Manual
Cuisinart Blender 09CE13231 User Manual
Curtis Portable Radio RT111 User Manual
Dell Server 35XX User Manual
Fisher Price Baby Toy 77493 User Manual
Gitzo Camcorder Accessories GT2531 User Manual