-ꢀ
ꢀ
ꢀꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
AꢀSierraꢀMonitorꢀCompanyꢀ
Driver Manual
(Supplement to the FieldServer Instruction Manual)ꢀ
FS-8700-41 Simplex Time Recorder
Company - 4100 Computer Port Protocol
APPLICABILITY & EFFECTIVITY
Effective for all systems manufactured after May 1, 2001
Driver Version:
1.07
Document Revision: 8
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex Driver Manual
Table of Contents
AppendixꢀA.11. AdvancedꢀMapꢀDescriptorꢀExampleꢀ2.ꢀꢁꢀReadꢀPanelꢀTime.........................33
AppendixꢀA.12. AdvancedꢀMapꢀDescriptorꢀExampleꢀ3ꢀꢁꢀWriteꢀPanelꢀTime..........................34
AppendixꢀA.13. AdvancedꢀMapꢀDescriptorꢀExampleꢀ4ꢀꢁꢀPanelꢀRevisionꢀInformation...........34
AppendixꢀA.14. AdvancedꢀMapꢀDescriptorꢀExampleꢀ5ꢀꢁꢀAckAll ...........................................35
AppendixꢀA.15. AdvancedꢀMapꢀDescriptorꢀExampleꢀ6ꢀꢁꢀSilenceꢀ/ꢀReset .............................35
AppendixꢀA.16. AdvancedꢀMapꢀDescriptorꢀExampleꢀ7ꢀꢁꢀAcknowledgeꢀaꢀspecificꢀpoint........36
AppendixꢀA.17. AdvancedꢀMapꢀDescriptorꢀExampleꢀ8ꢀꢁꢀClearAll.........................................37
AppendixꢀA.18. AdvancedꢀMapꢀDescriptorꢀExampleꢀ9ꢀꢁꢀEarths...........................................38
AppendixꢀA.19. AdvancedꢀMapꢀDescriptorꢀExampleꢀ10ꢀꢁꢀShow ..........................................39
AppendixꢀA.20. UsingꢀClistꢀtoꢀWriteꢁThroughꢀandꢀStoreꢀpointꢀstatusꢀfromꢀUnsolicitedꢀ
Messagesꢀ41
Appendix B. Troubleshooting Tips....................................................................................42
AppendixꢀB.1. AddressꢀErrors.............................................................................................42
AppendixꢀB.2. DriverꢀLimitations .........................................................................................42
AppendixꢀB.3. ResolvingꢀNetworkꢀAddressesꢀaboveꢀ255....................................................43
Appendix C. Error Messages .............................................................................................44
Appendix D. Pseudo Points ...............................................................................................49
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 4 of 58
1.
Simplex Time Recorder Company - 4100 Computer Port Protocol
Theꢀ Simplexꢀ Timeꢀ Recorderꢀ Companyꢀ ꢁꢀ 4100ꢀ Computerꢀ Portꢀ Protocolꢀ driverꢀ allowsꢀ theꢀ
FieldServerꢀtoꢀtransferꢀdataꢀtoꢀandꢀfromꢀdevicesꢀoverꢀeitherꢀRSꢁ232ꢀorꢀRSꢁ485ꢀusingꢀSimplexꢀ
TimeꢀRecorderꢀCompanyꢀꢁꢀ4100ꢀComputerꢀPortꢀProtocol.ꢀꢀꢀ
ꢀ
Thisꢀ driverꢀ isꢀ designedꢀ toꢀ connectꢀ toꢀ aꢀ Simplexꢀ 4100ꢀ panelꢀ equippedꢀ toꢀ supportꢀ theꢀ “4100ꢀ
ComputerꢀPortꢀProtocol”ꢀasꢀdefinedꢀinꢀSimplex’sꢀdocumentꢀ950ꢁ004ꢀRevisionꢀEꢀdatedꢀ28ꢀJulyꢀ
2000.ꢀ ꢀ Theꢀ implementationꢀ providesꢀ aꢀ selectedꢀ subsetꢀ ofꢀ protocolꢀ functionsꢀ andꢀ subsetꢀ ofꢀ
functionalityꢀ forꢀ eachꢀ ofꢀ theseꢀ selectedꢀ functions.ꢀ ꢀ Itꢀ isꢀ importantꢀ toꢀ noteꢀ theꢀ exclusionsꢀ andꢀ
limitationsꢀdescribedꢀinꢀthisꢀdocument.ꢀ
ꢀ
Theꢀ driverꢀ isꢀ aꢀ capableꢀ ofꢀ parsingꢀ andꢀ storingꢀ informationꢀ sentꢀ byꢀ aꢀ panelꢀ inꢀ theꢀ formꢀ ofꢀ
unsolicitedꢀmessagesꢀwhichꢀareꢀtypicallyꢀgeneratedꢀwhenꢀthereꢀisꢀaꢀstateꢀchangeꢀinꢀtheꢀpanelꢀorꢀ
oneꢀofꢀtheꢀconnectedꢀdevices.ꢀꢀTheꢀdriverꢀisꢀalsoꢀcapableꢀofꢀpollingꢀforꢀpointꢀandꢀpanelꢀstatusꢀ
dataꢀandꢀsomeꢀadditionalꢀdataꢀsuchꢀasꢀtheꢀpanel’sꢀtimeꢀandꢀrevisionꢀinformation.ꢀꢀInꢀadditionꢀtheꢀ
driverꢀ isꢀ capableꢀ ofꢀ settingꢀ someꢀ controlꢀ pointsꢀ inꢀ theꢀ panelꢀ –ꢀ acknowledgingꢀ andꢀ resettingꢀ
alarmsꢀandꢀwritingꢀdataꢀ(whereꢀpermitted)ꢀtoꢀsomeꢀanalogꢀandꢀdiscreteꢀpoints.ꢀ
ꢀ
ThisꢀisꢀaꢀclientꢀonlyꢀdriverꢀandꢀisꢀnotꢀcapableꢀofꢀemulatingꢀaꢀSimplexꢀPanel.ꢀꢀServerꢀemulationꢀisꢀ
providedꢀforꢀtestꢀpurposesꢀonlyꢀandꢀisꢀnotꢀsupportedꢀorꢀdocumented.ꢀ
ꢀ
1.1.
Supported Panel Types
Theꢀdriverꢀhasꢀbeenꢀtestedꢀagainstꢀ4020,ꢀ4100ꢀandꢀ4100Uꢀpanels.ꢀThereꢀisꢀnoꢀdifferenceꢀinꢀ
theꢀprotocolꢀformatꢀbetweenꢀtheꢀvariousꢀpanels.ꢀWhatꢀchangesꢀisꢀtheꢀpanelꢀfirmwareꢀversionꢀ
andꢀwithꢀtheꢀfirmwareꢀchangesꢀtheꢀsupportedꢀfunctionꢀsetꢀchanges.ꢀ
ꢀ
1.2.
Simplex Panel Firmware Revision vs. Supported Functionality
Thisꢀdriverꢀwasꢀprimarilyꢀtestedꢀagainstꢀaꢀ4020ꢀpanelꢀwithꢀfirmwareꢀrevisionꢀ9.2.ꢀBetaꢀtestingꢀ
againstꢀaꢀ4100ꢀpanelꢀwithꢀaꢀfirmwareꢀrevisionꢀ10.xꢀwasꢀalsoꢀperformed.ꢀ
ꢀ
AꢀgridꢀofꢀfirmwareꢀrevisionꢀnumberꢀandꢀsupportedꢀfunctionsꢀisꢀprovidedꢀbyꢀSimplex.ꢀꢀThisꢀ
gridꢀisꢀavailableꢀfromꢀSimplex.ꢀꢀRequestꢀtheꢀ‘CPPꢀRevisionꢀCompatibility’ꢀTable.ꢀ
ꢀ
Allꢀtheꢀfunctionsꢀdescribedꢀinꢀthisꢀmanualꢀareꢀsupportedꢀforꢀfirmwareꢀrevisionsꢀ10ꢀorꢀhigher.ꢀꢀ
Forꢀrevisionsꢀbetweenꢀ9.2ꢀandꢀ10,ꢀtheꢀ‘Earths’ꢀandꢀ‘Value’ꢀfunctionsꢀdescribedꢀinꢀthisꢀdriverꢀ
areꢀ notꢀ supportedꢀ byꢀ theꢀ Simplexꢀ Panels.ꢀ ꢀ Forꢀ revisionsꢀ lowerꢀ thanꢀ 9.2,ꢀ thenꢀ functionsꢀ
supportedꢀ needꢀ toꢀ beꢀ determinedꢀ byꢀ trialꢀ andꢀ error.ꢀ ꢀ Weꢀ areꢀ fairlyꢀ confidentꢀ thatꢀ allꢀ theꢀ
functionsꢀsupportedꢀbyꢀversionꢀ9xꢀareꢀalsoꢀsupportedꢀbyꢀversionsꢀ8xꢀofꢀtheꢀpanelꢀfirmware.ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 5 of 58
2.
Driver Scope of Supply
2.1. Supplied by FieldServer Technologies for this driver
FieldServer Technologies
PART #
Description
FSꢁ8917ꢁ16ꢀ
EthernetꢀCableꢀwithꢀpigtailꢀ(4020ꢀandꢀ4100ꢀPanels)ꢀ
Ethernetꢀ cableꢀ withꢀ 25ꢀ pinꢀ maleꢀ connector.ꢀ (4100uꢀ
Panels)ꢀ
FSꢁ8917ꢁ07ꢀ
SPA59132ꢀ
RSꢁ485ꢀconnectionꢀadapterꢀ
FSꢁ8700ꢁ41ꢀ
DriverꢀManual.ꢀ
ꢀ
2.2.
Provided by Supplier of 3rd Party Equipment
Toꢀenableꢀtheꢀ4100ꢀProtocol,ꢀtheꢀ4100ꢀsystem,ꢀsuppliedꢀbyꢀtheꢀuser,ꢀmustꢀhaveꢀaꢀfreeꢀRSꢁ
232ꢀportꢀdedicatedꢀforꢀuseꢀwithꢀtheꢀcomputerꢀdevice.ꢀꢀInꢀmostꢀcases,ꢀthisꢀisꢀnotꢀincludedꢀinꢀ
theꢀbaseꢀconfigurationꢀofꢀtheꢀproductꢀprovidedꢀbyꢀTheꢀSimplexꢀTimeꢀRecorderꢀCompany,ꢀ
andꢀmustꢀbeꢀaddedꢀasꢀaꢀsalesꢀoption.ꢀꢀAllꢀ4100ꢀsystemsꢀlimitꢀtheꢀnumberꢀofꢀcomputerꢀportsꢀ
activeꢀatꢀoneꢀtimeꢀinꢀaꢀsystem.ꢀꢀToꢀdetermineꢀtheꢀlimitꢀforꢀtheꢀspecificꢀproductꢀconfiguration,ꢀ
referꢀtoꢀtheꢀspecificꢀproductꢀspecifications,ꢀorꢀcontactꢀaꢀSimplexꢀsalesꢀrepresentative.ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 6 of 58
3.
Hardware Connections
Theꢀ FieldServerꢀ isꢀ connectedꢀ toꢀ theꢀ Simplexꢀ Device’sꢀ RSꢁ232ꢀ portꢀ ofꢀ deviceꢀ typeꢀ
"COMPUTER",ꢀ theꢀ followingꢀ portꢀ attributesꢀ mayꢀ beꢀ configuredꢀ specificallyꢀ forꢀ thatꢀ particularꢀ
port:ꢀꢀ
ꢀ
Ensureꢀthatꢀtheseꢀsettingsꢀcorrespondꢀtoꢀtheꢀsettingsꢀdescribedꢀinꢀsectionꢀ4ꢀofꢀthisꢀdocument.ꢀ
ꢀ
Sim4100 Panel
Setting
BaudꢀRateꢀ 9600ꢀ
Parityꢀ
DataꢀBitsꢀ
StopꢀBitsꢀ
ꢀ
Default Options
75,ꢀ110,ꢀ134.5,ꢀ300,ꢀ600,ꢀ1200,ꢀ1800,ꢀ2000,ꢀ2400,ꢀ4800,ꢀ9600,ꢀ19200ꢀ
EVEN1ꢀ ODD,ꢀEVEN,ꢀMARK,ꢀSPACE,ꢀNONEꢀ
8ꢀ
1ꢀ
7ꢀorꢀ8ꢀ
1ꢀorꢀ2ꢀ
Sim4100U Panel
Setting Default Options
BaudꢀRateꢀ 9600ꢀ 75,ꢀ110,ꢀ134.5,ꢀ300,ꢀ600,ꢀ1200,ꢀ1800,ꢀ2000,ꢀ2400,ꢀ4800,ꢀ9600,ꢀ19200ꢀ
NONE1ꢀ ODD,ꢀEVEN,ꢀMARK,ꢀSPACE,ꢀNONEꢀ
Parityꢀ
DataꢀBitsꢀ
StopꢀBitsꢀ
8ꢀ
1ꢀ
7ꢀorꢀ8ꢀ
1ꢀorꢀ2ꢀ
ꢀ
ꢀ
TheꢀfollowingꢀareꢀtheꢀSimplex,ꢀrecommendedꢀconnectionsꢀtoꢀbeꢀusedꢀinꢀcablingꢀbetweenꢀtheꢀ
4100ꢀandꢀtheꢀFieldServerꢀdevice.ꢀꢀForꢀtheꢀcomputerꢀdevice,ꢀtheꢀstandardꢀEIAꢀsignalꢀdescription,ꢀ
andꢀtheꢀ25ꢀpinꢀ(DB25)ꢀandꢀ9ꢀpinꢀ(DB9)ꢀconnectorꢀassignmentsꢀareꢀshown.ꢀꢀꢀ
ꢀ
4100 Host
4100
Port
Computer
Cable
Signal
Signal
DB25Pin
DB9Pin
2ꢀ
3ꢀ
7ꢀ
8ꢀ
5ꢀ
Port
ATB1
8ꢀ
6ꢀ
7ꢀ
DB25 Pin
BTB2
1ꢀ
3ꢀ
2ꢀ
4ꢀ
2ꢀ
3ꢀ
4ꢀ
5ꢀ
7ꢀ
TXDꢀ
RXDꢀ
RTSꢀ
CTSꢀ
GNDꢀ
→ꢀ
←ꢀ
2ꢀ
RXDꢀ
TXDꢀ
RTSꢀ
CTSꢀ
GNDꢀ
2ꢀ
3ꢀ
4ꢀ
5ꢀ
7ꢀ
5ꢀ
4ꢀ
ꢀ
5ꢀ
──ꢀ
ꢀ
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ ꢀꢀꢀꢀꢀꢀꢀ
1ꢀOddꢀorꢀEvenꢀparityꢀisꢀrecommendedꢀ(byꢀSimplex)ꢀtoꢀprovideꢀadditionalꢀerrorꢀdetectionꢀatꢀtheꢀcharacterꢀ
level.
ꢀ
2ꢀNote,ꢀthatꢀifꢀHSHAKEꢀisꢀnotꢀusedꢀ(SimplexꢀDeviceꢀSetting),ꢀtheꢀconnectionsꢀbetweenꢀRTSꢀandꢀCTSꢀꢀareꢀ
notꢀrequiredꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 7 of 58
3.1.
Connection to a Simplex 4020 Panel
Communication Board
Chipꢀ4100ꢀRS2120ꢀ
ꢀ
Cardꢀ4020/RSꢁ232/2120ꢀmodemꢀreadyꢀ
assembly.ꢀꢀ
Terminal Block Markings
PortꢀAꢀ=1ꢁ5,ꢀPortꢀB=6ꢁ10.ꢀꢀ
ꢀꢀ
1=+com(xmt).ꢀꢀ
2=+com(rts),ꢀ
3=ꢁcom(rcv),ꢀꢀ
4=ꢁcom(cts),ꢀꢀ
5=gnd,ꢀꢀ
6=xmt,ꢀꢀ
7=rts,ꢀ
8=rcv,ꢀ
9=cts,ꢀ
10=gnd,ꢀꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Serial Connection
Page 8 of 58
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 9 of 58
3.2.
Connection to a Simplex 4100 Panel
WIRE LIST
FROM SIMPLEXꢀ4100ꢀ
FSꢁX40ꢀ
FUNCTION
RX
TX
GND
PANEL
XMIT
RCV
RJ45ꢁ01
RJ45ꢁ08
RJ45ꢁ04
GND
SIMPLEXꢀ100ꢀ
PANEL
PORTꢀBꢀ
CONNECTION
GND
CTS
RCV
RTS
XMIT
FSꢁ8917ꢁ16
P1ꢁP8
P1
P2
P3
P4
P5
P6
P7
P8
R1ꢀꢀ
R2
N1ꢀꢀ N2ꢀꢀ
RS485
10ꢀBaseꢀT
ETHERNET
RS232
P1
P2
P3
P4
P5
P6
P7
P8
Rx Tx
R1
Rx Tx
R2
Rx Tx
Netꢀ1
Netꢀ2
Rx Tx Rx Tx Rx Tx Rx Tx Rx Tx Rx Tx Rx Tx
Tx Rx Con Tx Rx Con
(408)ꢁ262ꢁ2299
SIMPLEX 4100
CONNECTION DIAGRAM
BASE NAME:
FILE NAME: FS-T28700-41 .VSD
DATE: 09/26/07
BY: MN
ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 10 of 58
3.3.
Connection to a Simplex 4100U Panel
Frontꢀofꢀ4100UꢀPanelꢀ
PortꢀAꢀ
PortꢀBꢀ
ꢀ
ꢀ
Pinꢀ3ꢀꢁꢀBlueꢀ
Pinꢀ7ꢀꢁꢀGreenꢀ
Pinꢀ2ꢀꢁꢀWhiteꢀ
ꢀ
ꢀ
ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 11 of 58
ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 12 of 58
4.
Configuring the FieldServer as a Simplex Time Recorder Company - 4100
Computer Port Protocol Client
ForꢀaꢀdetailedꢀdiscussionꢀonꢀFieldServerꢀconfiguration,ꢀpleaseꢀreferꢀtoꢀtheꢀrelevantꢀinstructionꢀ
manual.ꢀ ꢀ Theꢀ informationꢀ thatꢀ followsꢀ describesꢀ howꢀ toꢀ expandꢀ uponꢀ theꢀ factoryꢀ defaultsꢀ
providedꢀinꢀtheꢀconfigurationꢀfilesꢀincludedꢀwithꢀtheꢀFieldServerꢀ(Seeꢀ“.csv”ꢀfilesꢀprovidedꢀwithꢀ
theꢀFieldServer).ꢀ
ꢀ
ThisꢀsectionꢀdocumentsꢀandꢀdescribesꢀtheꢀparametersꢀnecessaryꢀforꢀconfiguringꢀtheꢀFieldServerꢀ
toꢀ communicateꢀ withꢀ aꢀ Simplexꢀ Timeꢀ Recorderꢀ Companyꢀ ꢁꢀ 4100ꢀ Computerꢀ Portꢀ Protocolꢀ
Server.ꢀꢀ
ꢀ
TheꢀconfigurationꢀfileꢀtellsꢀtheꢀFieldServerꢀaboutꢀitsꢀinterfaces,ꢀandꢀtheꢀroutingꢀofꢀdataꢀrequired.ꢀ
InꢀorderꢀtoꢀenableꢀtheꢀFieldServerꢀforꢀSimplexꢀTimeꢀRecorderꢀCompanyꢀꢁꢀ4100ꢀComputerꢀPortꢀ
Protocolꢀcommunications,ꢀtheꢀdriverꢀindependentꢀFieldServerꢀbuffersꢀneedꢀtoꢀbeꢀdeclaredꢀinꢀtheꢀ
“DataꢀArrays”ꢀsection,ꢀtheꢀdestinationꢀdeviceꢀaddressesꢀneedꢀtoꢀbeꢀdeclaredꢀinꢀtheꢀ“ClientꢀSideꢀ
Nodes”ꢀsection,ꢀandꢀtheꢀdataꢀrequiredꢀfromꢀtheꢀserversꢀneedsꢀtoꢀbeꢀmappedꢀinꢀtheꢀ“ClientꢀSideꢀ
MapꢀDescriptors”ꢀsection.ꢀꢀDetailsꢀonꢀhowꢀtoꢀdoꢀthisꢀcanꢀbeꢀfoundꢀbelow.ꢀ
ꢀ
Noteꢀthatꢀinꢀtheꢀtables,ꢀ*ꢀindicatesꢀanꢀoptionalꢀparameter,ꢀwithꢀtheꢀboldꢀlegalꢀvalueꢀbeingꢀtheꢀ
default.ꢀ
4.1.
Data Arrays
SectionꢀTitleꢀ
Data_Arraysꢀ
ColumnꢀTitleꢀ
Data_Array_Nameꢀ ProvideꢀnameꢀforꢀDataꢀArrayꢀ
Functionꢀ
LegalꢀValuesꢀ
Upꢀtoꢀ15ꢀalphanumericꢀcharactersꢀ
Provideꢀdataꢀformat.ꢀEachꢀDataꢀ FLOAT,ꢀBIT,ꢀUint16,ꢀSint16,ꢀ
Data_Formatꢀ
Arrayꢀcanꢀonlyꢀtakeꢀonꢀoneꢀ
format.ꢀ
Packed_Bit,ꢀByte,ꢀPacked_Byte,ꢀ
Swapped_Byteꢀ
NumberꢀofꢀDataꢀObjects.ꢀꢀMustꢀ
Data_Array_Lengthꢀ beꢀlargerꢀthanꢀtheꢀrequiredꢀdataꢀ 1ꢁ65535ꢀ
storageꢀarea.ꢀ
ꢀ
Example
ꢀ
//ꢀꢀꢀꢀDataꢀArraysꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Data_Arraysꢀ
Data_Array_Name,ꢀ
DA_AI_01,ꢀ
DA_AO_01,ꢀ
DA_DI_01,ꢀ
DA_DO_01,ꢀ
ꢀ
ꢀ
ꢀ
Data_Format,ꢀ
UInt16,ꢀ
UInt16,ꢀ
Bit,ꢀ
Data_Array_Lengthꢀ
200ꢀ
200ꢀ
200ꢀ
200
Bit,ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 13 of 58
4.2.
Client Side Connection Descriptions
Section Title
Connectionsꢀ
Column Title
Function
Legal Values
P1ꢁP8,ꢀR1ꢁR23ꢀ
Specifyꢀwhichꢀportꢀtheꢀdeviceꢀisꢀconnectedꢀ
toꢀtheꢀFieldServerꢀ
Portꢀ
110ꢀ–ꢀ115200,ꢀstandardꢀbaudꢀ
ratesꢀonly.ꢀꢀꢀ
Even,ꢀOdd,ꢀNone,ꢀMark,ꢀ
Spaceꢀ
Baud*ꢀ
Parity*ꢀ
Specifyꢀbaudꢀrateꢀ
Specifyꢀparityꢀ
Data_Bits*ꢀ
Stop_Bits*ꢀ
Protocolꢀ
Specifyꢀdataꢀbitsꢀ
Specifyꢀstopꢀbitsꢀ
7,ꢀ8ꢀ
1ꢀ
Specifyꢀprotocolꢀusedꢀ
sim4100ꢀꢀ
Handshaking*ꢀ Specifyꢀhardwareꢀhandshakingꢀ
RTS,ꢀRTS/CTS,ꢀNoneꢀ
0ꢁ32000ꢀseconds,ꢀ1 secondꢀ
PollꢀDelay*ꢀ
Timeꢀbetweenꢀinternalꢀpollsꢀ
Example
ꢀ
// ClientꢀSideꢀConnectionsꢀ
ꢀ
Connectionsꢀ
Port,ꢀ
P8,ꢀ
Protocol,ꢀ
Sim4100,ꢀ
Baud,ꢀ Parity,ꢀ
9600,ꢀ Even,ꢀ
Handshaking,ꢀ
None,ꢀ
Poll_Delayꢀ
0.100sꢀ
ꢀ
4.3.
Client Side Node Descriptors
SectionꢀTitleꢀ
Nodesꢀ
ColumnꢀTitleꢀ
Functionꢀ
LegalꢀValuesꢀ
Node_Nameꢀ Provideꢀnameꢀforꢀnodeꢀ
Upꢀtoꢀ32ꢀalphanumericꢀcharactersꢀ
ThisꢀparameterꢀisꢀIGNORED.ꢀSpecialꢀ
keywordsꢀtoꢀdefineꢀtheꢀcardꢁsubꢁpointꢀ
areꢀdescribedꢀinꢀsectionꢀ4.4ꢀ
Sim4100ꢀ
Node_IDꢀ
Adꢀ
Protocolꢀ
Portꢀ
Specifyꢀprotocolꢀusedꢀ
Specifyꢀwhichꢀportꢀtheꢀdeviceꢀisꢀ
connectedꢀtoꢀtheꢀFieldServerꢀ
RequiredꢀforꢀSimplex4100ꢀPanels.ꢀ
IfꢀnotꢀspecifiedꢀthenꢀaꢀSimplexꢀ
4100/4020ꢀpanelꢀisꢀassumed.ꢀ
ꢀ
P1ꢁP8,ꢀR1ꢁR23ꢀ
PLC_Type*ꢀ 4020/4100ꢀꢁꢀpanelsꢀwithꢀfirmwareꢀ
versionꢀ9xꢀorꢀearlier.ꢀ
4100,ꢀ4020,ꢀ4100Uꢀ
ꢀ
4100Uꢀ–ꢀpanelsꢀwithꢀfirmwareꢀ
versionꢀ10xꢀorꢀlater.ꢀ
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ ꢀꢀꢀꢀꢀꢀꢀ
3ꢀNotꢀallꢀportsꢀshownꢀareꢀnecessarilyꢀsupportedꢀbyꢀtheꢀhardware.ꢀConsultꢀtheꢀappropriateꢀInstructionꢀ
manualꢀforꢀdetailsꢀofꢀtheꢀportsꢀavailableꢀonꢀspecificꢀhardware.ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 14 of 58
Example
ꢀ
//ꢀꢀꢀꢀClientꢀSideꢀNodesꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Nodesꢀ
Node_Name,ꢀꢀꢀꢀꢀ
Device1,ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀ
PLC_Type,ꢀ
4100U,ꢀ
Protocol,ꢀ
Sim4100,ꢀ
Connectionꢀ
P8ꢀ
4.4.
Client Side Driver Tables
Aꢀdriverꢀtableꢀisꢀusedꢀtoꢀextendꢀaꢀtableꢀofꢀvalues/attributesꢀthatꢀhaveꢀbeenꢀhardꢀcodedꢀintoꢀ
theꢀdriver.ꢀꢀItꢀisꢀpossibleꢀtoꢀextendꢀtheꢀtablesꢀusingꢀCSVꢀfileꢀparameters.ꢀ
ꢀ
AdditionalꢀinformationꢀonꢀtheꢀuseꢀofꢀtheseꢀtablesꢀmayꢀbeꢀfoundꢀinꢀAppendixꢀA.8ꢀꢀ
ꢀ
4.4.1. SHOW Response Attributes Driver Table
Column Title
Function
Legal Values
Theꢀprotocolꢀmustꢀbeꢀspecifiedꢀonꢀeachꢀrowꢀ
ofꢀaꢀdriverꢀtable.ꢀ
Protocolꢀ
Sim4100ꢀ
Theꢀexactꢀ
characterꢀ
TheꢀSHOWꢀcommandꢀresponseꢀconsistsꢀofꢀ
aꢀnumberꢀofꢀattributesꢀandꢀtheirꢀcurrentꢀ
state/ꢀvalues.ꢀ
ꢀ
Useꢀthisꢀparameterꢀtoꢀaddꢀaꢀnewꢀattributeꢀtoꢀ
theꢀtable.ꢀ
sequenceꢀthatꢀ
mustꢀbeꢀ
specified.ꢀꢀMayꢀ
includeꢀanꢀequalꢀ
sign.ꢀ
sim4100_Attr_Nameꢀ
sim4100_Attr_Offsetꢀ
Ifꢀtheꢀresponseꢀcontainsꢀtheꢀattributeꢀdefinedꢀ
above,ꢀitsꢀcurrentꢀstate/valueꢀmustꢀbeꢀstoredꢀ
atꢀoffsetꢀxꢀinꢀtheꢀassociatedꢀDataꢀArray.ꢀꢀ
Useꢀthisꢀparameterꢀtoꢀdefineꢀx.ꢀꢀTakeꢀcareꢀtoꢀ
leaveꢀenoughꢀspaceꢀforꢀthoseꢀattributesꢀ
whichꢀhaveꢀmultipleꢀvalues.ꢀ
Mayꢀnotꢀbeꢀzero.ꢀ
Thisꢀparameterꢀtellsꢀtheꢀdriverꢀhowꢀtoꢀ
convertꢀtheꢀcurrentꢀstate/valueꢀforꢀstorageꢀinꢀ
theꢀDataꢀArray.ꢀꢀForꢀexample,ꢀtheꢀdriverꢀ
cannotꢀstoreꢀtheꢀstateꢀ‘Normal’ꢀ.ꢀByꢀ
1,2,3ꢀ
Mayꢀnotꢀbeꢀzero.ꢀ
sim4100_Attr_Methodꢀ specifyingꢀmethodꢀ1,ꢀyouꢀtellꢀtheꢀdriverꢀtoꢀ
useꢀtheꢀstateꢀdescriptorꢀ‘Normal’ꢀinꢀaꢀlookupꢀ
tableꢀofꢀattributeꢀstatesꢀtoꢀfindꢀtheꢀvalueꢀ
associatedꢀtoꢀNormalꢀandꢀtoꢀstoreꢀthatꢀ
value.ꢀ
ꢀ
ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 15 of 58
4.4.2. SHOW Response Attribute States Driver Table
Column Title
Function
Legal Values
Theꢀprotocolꢀmustꢀbeꢀ
Protocolꢀ
specifiedꢀonꢀeachꢀrowꢀofꢀ Sim4100ꢀ
aꢀdriverꢀtable.ꢀ
Useꢀthisꢀparameterꢀtoꢀ
extendꢀthisꢀlistꢀofꢀ
predefinedꢀattributeꢀ
states.ꢀ
Defineꢀaꢀstateꢀwordꢀsuchꢀasꢀ
‘Normal’ꢀandꢀassociateꢀaꢀ
valueꢀusingꢀtheꢀ‘value’ꢀ
parameter.ꢀ
sim4100_Attr_State_Nameꢀ
Thisꢀparameterꢀisꢀtheꢀ
sim4100_Attr_State_Valueꢀ valueꢀtoꢀbeꢀassociatedꢀ
withꢀtheꢀ‘name’ꢀ
Mayꢀnotꢀbeꢀzero.ꢀ
ꢀ
4.5.
Client Side Map Descriptors
4.5.1. FieldServer Specific Map Descriptor Parameters
ColumnꢀTitleꢀ
Functionꢀ
NameꢀofꢀthisꢀMapꢀ
Descriptorꢀ
LegalꢀValuesꢀ
Upꢀtoꢀ32ꢀalphanumericꢀ
charactersꢀ
Map_Descriptor_Nameꢀ
NameꢀofꢀDataꢀArrayꢀwhereꢀ OneꢀofꢀtheꢀDataꢀArrayꢀ
Data_Array_Nameꢀ
dataꢀisꢀtoꢀbeꢀstoredꢀinꢀtheꢀ
FieldServerꢀ
namesꢀfromꢀ“DataꢀArray”ꢀ
sectionꢀaboveꢀ
StartingꢀlocationꢀinꢀDataꢀ
Arrayꢀ
FunctionꢀofꢀClientꢀMapꢀ
Descriptorꢀ
0ꢀtoꢀmaximumꢀspecifiedꢀinꢀ
“DataꢀArray”ꢀsectionꢀaboveꢀ
Data_Array_Locationꢀ
Functionꢀ
RDBC,ꢀWRBC,ꢀWRBXꢀ
4.5.2. Driver Specific Map Descriptor Parameters
ColumnꢀTitleꢀ Functionꢀ
LegalꢀValuesꢀ
Oneꢀofꢀtheꢀnodeꢀ
namesꢀspecifiedꢀinꢀ
“ClientꢀNodeꢀ
Node_Nameꢀ NameꢀofꢀNodeꢀtoꢀfetchꢀdataꢀfromꢀ
Descriptor”ꢀaboveꢀ
LengthꢀofꢀMapꢀDescriptorꢀꢁꢀmustꢀalwaysꢀbeꢀ
specified.ꢀ
Ifꢀtheꢀlengthꢀofꢀtheꢀresponseꢀ(suchꢀasꢀerrorsꢀ/ꢀ
earths,ꢀshow,ꢀrevision)ꢀisꢀnotꢀknownꢀinꢀadvanceꢀitꢀ
shouldꢀbeꢀsetꢀtoꢀaꢀvalueꢀlargeꢀenoughꢀtoꢀstoreꢀtoꢀ
allowꢀsomeꢀcontingency.ꢀIfꢀdataꢀcannotꢀbeꢀstoredꢀ
becauseꢀanꢀarrayꢀisꢀtooꢀshortꢀtheꢀdriverꢀwillꢀ
produceꢀaꢀmessageꢀinꢀtheꢀerrorꢀlog.ꢀ
Lengthꢀ
ꢀꢀ
Notꢀrequired.ꢀꢀTheꢀaddressꢀisꢀspecifiedꢀbyꢀusingꢀtheꢀcardꢁpointꢁsubꢀ
specificationꢀdescribedꢀinꢀsectionꢀ4.4.2ꢀ
Addressꢀ
4.5.3. Timing Parameters
ColumnꢀTitleꢀ
Scan_Intervalꢀ
Functionꢀ
Rateꢀatꢀwhichꢀdataꢀisꢀpolledꢀ
LegalꢀValuesꢀ
>0.1sꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 16 of 58
4.5.4. Protocol (Simplex Device) Specific Parameters
Column Title
Function
Legal Values
Furtherꢀnotesꢀonꢀ
theseꢀkeywordsꢀ
areꢀprovidedꢀinꢀ
AppendixꢀAꢀ
ꢀ
Ackall,ꢀSetd,ꢀ
Disable,ꢀRestart,ꢀ
Clistall,ꢀClist,ꢀ
Time,ꢀCtime,ꢀ
Ack,ꢀ
Aꢀkeywordꢀwhichꢀcontrolsꢀtheꢀfunctionꢀbeingꢀ
performedꢀorꢀtheꢀtypeꢀofꢀdataꢀbeingꢀpolledꢀ/ꢀ
written.ꢀ
sim4100_funcꢀ
Xpoint,ꢀSeta,ꢀ
Super,ꢀShow,ꢀ
Earths,ꢀValue,ꢀ
ClearAllꢀ
TheꢀSimplex Time Recorder Company - 4100 Computer Port Protocolꢀonlyꢀusesꢀtheꢀ
standardꢀ4100ꢀaddressꢀformatꢀofꢀ<Card>ꢁ<Point>ꢁ<Subꢁpoint>.ꢀSymbolicꢀaddressingꢀisꢀ
notꢀsupported.ꢀTheꢀfollowingꢀkeywordsꢀareꢀusedꢀtoꢀaddressꢀdevices.ꢀ
Furtherꢀnotesꢀ
andꢀexamplesꢀ
areꢀprovidedꢀinꢀ
AppendixꢀAꢀ
sim4100_Cardꢀ
sim4100_Pointꢀ
sim4100_Subꢀ
SimplexꢀAddressꢀ<Card>ꢀ
SimplexꢀAddressꢀ<Point>ꢀ
SimplexꢀAddressꢀ<Sub_Type>ꢀ
Onlyꢀappropriateꢀwhenꢀtheꢀ
sim4100_func=clist.ꢀ
Controlsꢀtheꢀwriteꢀthroughꢀbehaviorꢀofꢀtheꢀ
clistꢀfunction.ꢀSeeꢀAppendixꢀA.20ꢀforꢀ
additionalꢀinformation.ꢀ
Whenꢀusingꢀtheꢀdefaultꢀvalueꢀthenꢀtheꢀwriteꢀ
commandsꢀareꢀdoneꢀusingꢀtheꢀformatꢀSETꢀ
cꢁpꢁsꢀON/OFF.ꢀIfꢀtheꢀparameterꢀisꢀsetꢀtoꢀ
valueꢀthenꢀwritesꢀareꢀdoneꢀusingꢀtheꢀformatꢀ
SETꢀcꢁpꢁsꢀvalue.ꢀ
sim4100_WriteThru*ꢀ
Onoff,ꢀvalueꢀ
Controlꢀtheꢀabilityꢀofꢀ‘CLIST’ꢀmapꢀdescriptorsꢀ
toꢀbeꢀusedꢀtoꢀstoreꢀdataꢀfromꢀunsolicitedꢀ
messages.ꢀꢀReferꢀalsoꢀtoꢀAppendixꢀA.20ꢀ
ꢀ
Store_Unsolicited*ꢀ
ꢀ
Yes/Noꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 19 of 58
5.
Configuring the FieldServer as a Simplex Time Recorder Company - 4100
Computer Port Protocol Server
Theꢀ driverꢀ containsꢀ someꢀ serverꢀ sideꢀ functionalityꢀ whichꢀ hasꢀ beenꢀ developedꢀ toꢀ meetꢀ
FieldServer’sꢀcontinuousꢀqualityꢀassuranceꢀefforts.ꢀꢀHowever,ꢀtheꢀserverꢀsideꢀfunctionsꢀareꢀnotꢀ
documentedꢀ orꢀ supportedꢀ forꢀ customerꢀ use.ꢀ Ifꢀ youꢀ haveꢀ aꢀ strongꢀ requirementꢀ forꢀ thisꢀ
functionalityꢀthenꢀpleaseꢀcontactꢀtheꢀSalesꢀandꢀMarketingꢀgroupꢀofꢀFieldServer.ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 20 of 58
Appendix A. Advanced Topics
Appendix A.1. Hardware Handshaking
TheꢀdriverꢀdoesꢀnotꢀsupportꢀtheꢀSimplexꢀRTS/CTSꢀhandshakingꢀmodel.ꢀꢀThereforeꢀdeselectꢀ
theꢀHSHAKEꢀterminalꢀflagꢀorꢀconnectꢀCTSꢀtoꢀRTSꢀwithꢀaꢀjumperꢀonꢀtheꢀ4100ꢀside.ꢀ
ꢀ
Appendix A.2. Simplex Address Formatting – Specific Keywords
Theꢀ Simplexꢀ Timeꢀ Recorderꢀ Companyꢀ ꢁꢀ 4100ꢀ Computerꢀ Portꢀ Protocolꢀ onlyꢀ usesꢀ theꢀ
standardꢀ4100ꢀaddressꢀformatꢀofꢀ<Card>ꢁ<Point>ꢁ<Subꢁpoint>.ꢀꢀSymbolicꢀaddressingꢀisꢀnotꢀ
supported.ꢀꢀTheꢀfollowingꢀtableꢀlistsꢀkeywordsꢀwhichꢀcontrolꢀtheꢀbehaviorꢀofꢀtheꢀFieldServerꢀ
withꢀrespectꢀtoꢀconnectionꢀtoꢀaꢀSimplexꢀdeviceꢀandꢀtheꢀpermissibleꢀvaluesꢀdeterminingꢀtheꢀ
typeꢀofꢀdataꢀbeingꢀread/written.ꢀ
ꢀ
Keyword
Description
Function
Thisꢀcommandꢀacknowledgesꢀallꢀcardꢁpointꢁsubꢀstatesꢀ
basedꢀonꢀtheꢀvaluesꢀfoundꢀinꢀtheꢀassociatedꢀarrays.ꢀ
TheꢀFieldServerꢀwatchesꢀtheꢀDataꢀArrayꢀtoꢀseeꢀifꢀweꢀneedꢀ
toꢀsendꢀanꢀack.ꢀ
DAꢀelementꢀ Acceptedꢀ
1stꢀ–ꢀackꢀallꢀ
ꢀ
2ndꢀꢁꢀackꢀAꢀ primaryꢀabnormalꢀstateꢀ
3rdꢀ–ꢀackꢀFꢀ Fireꢀalarmꢀ
WRBCꢀ
Doꢀnotꢀspecifyꢀcꢁpꢁsꢀinꢀ
theꢀMapꢀDescriptor.ꢀ
Ackallꢀ
4thꢀ–ꢀackꢀPꢀ Priorityꢀ2ꢀ
5thꢀ–ꢀackꢀSꢀ Supervisoryꢀ
6thꢀ–ꢀackꢀTꢀ Troubleꢀ
7thꢀ–ꢀackꢀCꢀ Controlꢀ
Setꢀtheꢀarrayꢀelementꢀtoꢀ1ꢀtoꢀinitiateꢀtheꢀcommand.ꢀTheꢀ
FieldServerꢀclearsꢀtheꢀvalueꢀonꢀcompletion.ꢀ
Thisꢀcommandꢀallowsꢀtheꢀuserꢀtoꢀacknowledgeꢀaꢀsingleꢀ
point.ꢀꢀTheꢀspecifiedꢀDataꢀArrayꢀisꢀinspectedꢀandꢀtheꢀvalueꢀ
ofꢀtheꢀsingleꢀelementꢀisꢀusedꢀtoꢀdetermineꢀwhichꢀdeviceꢀ
state'sꢀareꢀack'd.ꢀReferꢀtoꢀAppendixꢀA.4ꢀꢀ
WRBCꢀ
Specifyꢀcꢁpꢁsꢀinꢀtheꢀ
MapꢀDescriptor.ꢀ
Ackꢀ
RDBCꢀ
Specifyꢀcꢁpꢁsꢀinꢀtheꢀ
MapꢀDescriptor.ꢀ
Thisꢀcommandꢀreturnsꢀtheꢀcurrentꢀpointꢀstatusꢀforꢀoneꢀ
point.ꢀꢀReferꢀtoꢀAppendixꢀA.4ꢀandꢀAppendixꢀA.20ꢀ
Clistꢀ
Thisꢀfunctionꢀobtainsꢀearth/groundꢀstatusꢀinformationꢀfromꢀ
theꢀpanel.ꢀꢀTwoꢀDataꢀArrayꢀelementsꢀareꢀusedꢀtoꢀstoreꢀtheꢀ
normalꢀ(=1)ꢀorꢀabnormalꢀ(=2)ꢀforꢀeachꢀcard.ꢀꢀTheꢀfirstꢀ
elementꢀisꢀforꢀtheꢀpositiveꢀgroundꢀandꢀtheꢀsecondꢀelementꢀ
isꢀtheꢀnegativeꢀground.ꢀꢀWhereꢀcardsꢀdoꢀnotꢀreportꢀboth,ꢀ
theꢀfirstꢀelementꢀofꢀtheꢀpairꢀisꢀused.ꢀ
Theꢀarrayꢀpositionꢀisꢀobtainedꢀbyꢀmultiplyingꢀtheꢀcardꢀ
numberꢀbyꢀtwoꢀandꢀaddingꢀtheꢀoffsetꢀspecifiedꢀinꢀtheꢀMapꢀ
Descriptor.ꢀꢀSetꢀtheꢀlengthꢀofꢀthisꢀMapꢀDescriptorꢀtoꢀtwiceꢀ
theꢀvalueꢀofꢀtheꢀmaximumꢀcardꢀnumber.ꢀ
RDBCꢀ
Doꢀnotꢀspecifyꢀcꢁpꢁsꢀinꢀ
theꢀMapꢀDescriptor.ꢀ
Earths4ꢀ
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ ꢀꢀꢀꢀꢀꢀꢀ
4ꢀThisꢀdriverꢀfunctionꢀusedꢀtheꢀSimplexꢀ‘CSHOWꢀcꢁpꢁsꢀCVAL’ꢀcommand.ꢀꢀItꢀisꢀonlyꢀsupportedꢀbyꢀpanelsꢀ
withꢀfirmwareꢀrevisionꢀnumbersꢀgreaterꢀthanꢀ10ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 21 of 58
Function
Keyword
Description
Storesꢀanalogꢀvalue(s)ꢀreadꢀfromꢀaꢀparticularꢀdevicewithoutꢀ
scalingꢀorꢀunits.ꢀꢀWhenꢀmoreꢀthanꢀoneꢀvalueꢀisꢀreportedꢀtheꢀ RDBCꢀ
Valueꢀ
driverꢀstoresꢀtheꢀvaluesꢀinꢀconsecutiveꢀarrayꢀelements.ꢀꢀ
Specifyꢀcꢁpꢁsꢀinꢀtheꢀ
EnsureꢀthatꢀtheꢀMapꢀDescriptor’sꢀusageꢀofꢀtheꢀDataꢀArraysꢀ MapꢀDescriptor.ꢀ
isꢀspacedꢀappropriately.ꢀ
EachꢀtypeꢀofꢀSimplexꢀdeviceꢀreportsꢀaꢀdifferentꢀsetꢀofꢀ
attributesꢀandꢀattributeꢀstates/values.ꢀꢀReferꢀtoꢀAppendixꢀ
A.8ꢀforꢀmoreꢀinformation.ꢀꢀTheꢀdriverꢀanalysesꢀtheꢀresponseꢀ
fromꢀtheꢀpoll.ꢀꢀWhenꢀanꢀattributeꢀisꢀrecognized,ꢀtheꢀattributeꢀ
stateꢀisꢀevaluated.ꢀꢀIfꢀthisꢀisꢀrecognizedꢀthenꢀtheꢀdriverꢀ
storesꢀaꢀvalue,ꢀcorrespondingꢀtoꢀtheꢀattributeꢀstate,ꢀatꢀanꢀ
arrayꢀlocationꢀcorrespondingꢀtoꢀtheꢀattribute.ꢀ4.4ꢀprovidesꢀ
RDBCꢀ
additionalꢀinformation.ꢀꢀTheꢀdriverꢀcanꢀonlyꢀrecognizeꢀ
Specifyꢀcꢁpꢁsꢀinꢀtheꢀ
Showꢀ
attributesꢀandꢀattributeꢀstatesꢀthatꢀitꢀisꢀprogrammedꢀtoꢀ
MapꢀDescriptor.ꢀ
recognize.ꢀ
UsingꢀtheꢀinformationꢀprovidedꢀinꢀAppendixꢀA.8,ꢀsetꢀtheꢀ
lengthꢀofꢀtheꢀMapꢀDescriptorꢀequalꢀtoꢀarrayꢀpositionꢀofꢀ
highestꢀattribute.ꢀ
EnsureꢀthatꢀMapꢀDescriptorsꢀusingꢀthisꢀfunctionꢀdoꢀnotꢀuseꢀ
overlappingꢀareasꢀofꢀtheꢀDataꢀArrays.ꢀꢀSeeꢀexampleꢀinꢀ
AppendixꢀA.19.ꢀ
Thisꢀ commandꢀ allowsꢀ theꢀ userꢀ toꢀ manipulateꢀ theꢀ statusꢀ
WRBCꢀ
and/orꢀpriorityꢀofꢀaꢀcontrolꢀpointꢀ
Specifyꢀcꢁpꢁsꢀinꢀtheꢀ
Setdꢀ
Setaꢀ
Theꢀportꢀaccessꢀlevelꢀmustꢀbeꢀsetꢀappropriatelyꢀinꢀtheꢀ
MapꢀDescriptor.ꢀ
Simplexꢀdeviceꢀotherwiseꢀtheꢀdeviceꢀreturnsꢀanꢀerror.ꢀ
Thisꢀcommandꢀallowsꢀtheꢀuserꢀto:ꢀ
•ꢀ Manipulateꢀtheꢀstatusꢀand/orꢀpriorityꢀofꢀaꢀcontrolꢀpointꢀ
•ꢀ Modifyꢀtheꢀvalueꢀofꢀanꢀanalogꢀpseudoꢀpoint.ꢀ
•ꢀ SetꢀtheꢀsensitivityꢀofꢀaꢀTrueAlarmꢀsensorꢀ
•ꢀ Setꢀ theꢀ rateꢁofꢁriseꢀ thresholdꢀ ofꢀ aꢀ TrueAlarmꢀ heatꢀ
sensorꢀ
WRBCꢀ
Specifyꢀcꢁpꢁsꢀinꢀtheꢀ
MapꢀDescriptor.ꢀ
•ꢀ Selectꢀtheꢀaudioꢀchannelꢀofꢀaꢀspeakerꢀcircuitꢀ
PointꢀStatusꢀChange.ꢀThisꢀisꢀanꢀunsolicitedꢀmessageꢀsentꢀ
automaticallyꢀbyꢀaꢀSimplexꢀdeviceꢀtoꢀreportꢀaꢀchangeꢀinꢀ
pointꢀstatus.ꢀꢀTheꢀcardꢁpointꢁsubꢀisꢀusedꢀtoꢀcalculateꢀanꢀ
offsetꢀintoꢀtheꢀassociatedꢀDataꢀArray.ꢀReadꢀAppendixꢀA.4ꢀtoꢀ
understandꢀthisꢀbetter.ꢀꢀ
Theꢀstateꢀbeingꢀreportedꢀdeterminesꢀtheꢀvalueꢀbeingꢀwrittenꢀ
intoꢀtheꢀDataꢀArray.ꢀReadꢀAppendixꢀA.5ꢀtoꢀunderstandꢀthisꢀ
better.ꢀ
Passiveꢀ
Specifyꢀcꢁpꢁsꢀinꢀtheꢀ
MapꢀDescriptor.ꢀ
Xpointꢀ
Disableꢀ
Restartꢀ
NotꢀImplementedꢀ
NotꢀImplementedꢀ
ꢀ
ꢀ
Thisꢀ commandꢀ setsꢀ andꢀ displaysꢀ theꢀ timeꢀ andꢀ dateꢀ inꢀ
"user"ꢀformat.ꢀꢀꢀ
Asꢀ aꢀ commandꢀ itꢀ setsꢀ theꢀ hourꢀ minuteꢀ secondꢀ ofꢀ theꢀ
Simplexꢀdeviceꢀbyꢀgettingꢀ theꢀvaluesꢀfromꢀtheꢀDataꢀArrayꢀ
associatedꢀ withꢀ theꢀ Mapꢀ Descriptor.ꢀ Theꢀ firstꢀ elementꢀ
containsꢀ theꢀ hour,ꢀ theꢀ secondꢀ theꢀ minuteꢀ andꢀ theꢀ thirdꢀ
containsꢀtheꢀsecond.ꢀꢀAꢀ24ꢀhourꢀclockꢀisꢀassumed.ꢀ
Asꢀaꢀquery,ꢀtheꢀdataꢀisꢀunpackedꢀintoꢀtheꢀDataꢀArrayꢀinꢀtheꢀ
sameꢀformatꢀasꢀdescribedꢀabove.ꢀ
RDBCꢀ(Query)ꢀorꢀ
WRBCꢀ(Set)ꢀ
Doꢀnotꢀspecifyꢀcꢁpꢁsꢀinꢀ
theꢀMapꢀDescriptor.ꢀ
Timeꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 22 of 58
Function
Keyword
Description
Asꢀaꢀcommandꢀitꢀsetsꢀtheꢀhourꢀminuteꢀsecondꢀofꢀtheꢀ
SimplexꢀdeviceꢀbyꢀgettingꢀtheꢀvaluesꢀfromꢀtheꢀDataꢀArrayꢀ
associatedꢀwithꢀtheꢀMapꢀDescriptor.ꢀTheꢀfirstꢀelementꢀ
containsꢀtheꢀhour,ꢀtheꢀsecondꢀtheꢀminute,ꢀtheꢀthirdꢀelementꢀ RDBCꢀ(Query)ꢀorꢀ
containsꢀtheꢀsecond,ꢀtheꢀ4thꢀcontainsꢀtheꢀdayꢀofꢀtheꢀweek,ꢀ
theꢀ5thꢀcontainsꢀtheꢀmonth,ꢀtheꢀ6thꢀcontainsꢀtheꢀdayꢀofꢀtheꢀ
monthꢀandꢀtheꢀ7thꢀelementꢀofꢀtheꢀarrayꢀcontainsꢀtheꢀyearꢀ
(valueꢀ01ꢀindicatesꢀ2001).ꢀꢀAꢀ24ꢀhourꢀclockꢀisꢀassumed.ꢀ
Asꢀaꢀquery,ꢀtheꢀdataꢀisꢀunpackedꢀintoꢀtheꢀDataꢀArrayꢀinꢀtheꢀ
sameꢀformatꢀasꢀdescribedꢀabove.ꢀ
WRBCꢀ(Set)ꢀ
Doꢀnotꢀspecifyꢀcꢁpꢁsꢀinꢀ
theꢀMapꢀDescriptor.ꢀ
Ctimeꢀ
UsedꢀtoꢀsendꢀaꢀsilenceꢀsignalꢀtoꢀtheꢀSimplexꢀdevice.ꢀꢀThisꢀ
isꢀaꢀtriggeredꢀcommand.ꢀꢀWhenꢀtheꢀelementꢀinꢀtheꢀDataꢀ
ArrayꢀassociatedꢀwithꢀtheꢀMapꢀDescriptorꢀisꢀsetꢀtoꢀ1ꢀthenꢀ
theꢀcommandꢀisꢀsentꢀtoꢀtheꢀSimplexꢀdevice.ꢀꢀTheꢀdriverꢀwillꢀ
setꢀtheꢀvalueꢀtoꢀzeroꢀwhenꢀtheꢀcommandꢀhasꢀbeenꢀ
acknowledged.ꢀ
UsedꢀtoꢀsendꢀaꢀresetꢀsignalꢀtoꢀtheꢀSimplexꢀdevice.ꢀ
Thisꢀisꢀaꢀtriggeredꢀcommand.ꢀꢀWhenꢀtheꢀelementꢀinꢀtheꢀ
DataꢀArrayꢀassociatedꢀwithꢀtheꢀMapꢀDescriptorꢀisꢀsetꢀtoꢀ1ꢀ
thenꢀtheꢀcommandꢀisꢀsentꢀtoꢀtheꢀSimplexꢀdevice.ꢀꢀTheꢀ
driverꢀwillꢀsetꢀtheꢀvalueꢀtoꢀzeroꢀwhenꢀtheꢀcommandꢀhasꢀ
beenꢀacknowledged.ꢀ
WRBCꢀ
Doꢀnotꢀspecifyꢀcꢁpꢁsꢀinꢀ
theꢀMapꢀDescriptor.ꢀ
Silenceꢀ
Resetꢀ
WRBCꢀ
Doꢀnotꢀspecifyꢀcꢁpꢁsꢀinꢀ
theꢀMapꢀDescriptor.ꢀ
UsedꢀtoꢀrequestꢀrevisionꢀinformationꢀfromꢀtheꢀSimplexꢀ
panel.ꢀꢀUseꢀofꢀthisꢀMapꢀDescriptorꢀisꢀrecommendedꢀasꢀitꢀ
allowsꢀtheꢀdriverꢀtoꢀgenerateꢀaꢀwarningꢀifꢀanꢀunknownꢀ
Simplexꢀrevisionꢀisꢀencountered.ꢀ
RDBCꢀ
Doꢀnotꢀspecifyꢀcꢁpꢁsꢀinꢀ
Revisionꢀ
MakeꢀsureꢀthatꢀtheꢀlengthꢀofꢀtheꢀMapꢀDescriptorꢀisꢀsufficientꢀ theꢀMapꢀDescriptor.ꢀ
toꢀstoreꢀallꢀtheꢀrevisionꢀinformation.ꢀAꢀLengthꢀofꢀ200ꢀisꢀ
recommended.ꢀ
Passiveꢀ
Doꢀnotꢀspecifyꢀcꢁpꢁsꢀinꢀ
theꢀMapꢀDescriptor.ꢀ
IfꢀusingꢀRUINETꢀtoꢀ
monitorꢀtheꢀ
FieldServer,ꢀdisplayꢀ
UseꢀthisꢀkeywordꢀtoꢀdefineꢀaꢀMapꢀDescriptorꢀwhichꢀtellsꢀtheꢀ theꢀDataꢀArrayꢀ
driverꢀwhereꢀtoꢀstoreꢀerrorꢀmessagesꢀreceivedꢀfromꢀtheꢀ
Simplexꢀdevice.ꢀTheꢀmostꢀrecentꢀmessageꢀisꢀstoredꢀinꢀtheꢀ
DataꢀArrayꢀspecified.ꢀMakeꢀsureꢀthatꢀtheꢀDataꢀArrayꢀlengthꢀ ‘String’ꢀformatꢀsoꢀthatꢀ
associatedꢀwithꢀthisꢀ
MapꢀDescriptorꢀinꢀ
Errorsꢀ
isꢀlongꢀenoughꢀtoꢀstoreꢀenoughꢀmeaningfulꢀinformation.ꢀꢀAꢀ
lengthꢀofꢀ200ꢀisꢀrecommended.ꢀ
youꢀcanꢀreadꢀtheꢀerrorꢀ
messageꢀeasily.ꢀꢀTheꢀ
driverꢀappendsꢀ
informationꢀaboutꢀtheꢀ
MapꢀDescriptorꢀwhichꢀ
generatedꢀtheꢀerrorꢀtoꢀ
makeꢀtheꢀerrorꢀmoreꢀ
easilyꢀunderstandable.ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 23 of 58
Function
Keyword
Description
MapꢀDescriptor’sꢀwhichꢀuseꢀthisꢀfunctionꢀdoꢀtwoꢀthings;ꢀ
Firstly,ꢀtheyꢀregisterꢀaꢀcꢁpꢁsꢀwithꢀtheꢀdriver.ꢀꢀ
SecondlyꢀtheyꢀdefineꢀaꢀDataꢀArrayꢀnameꢀandꢀelementꢀ
rangeꢀthatꢀmustꢀbeꢀsetꢀtoꢀzeroꢀwhenꢀtheꢀClearAllꢀfunctionꢀisꢀ
activated.ꢀ
Upꢀtoꢀ4ꢀcꢁpꢁs’sꢀmayꢀbeꢀregisteredꢀperꢀFieldServer.ꢀTheseꢀ
registeredꢀpointsꢀareꢀmonitoredꢀeachꢀtimeꢀaꢀClistꢀresponseꢀ
isꢀobtainedꢀasꢀwellꢀasꢀeachꢀtimeꢀtheꢀpanelꢀsendsꢀanꢀ
unsolicitedꢀXpointꢀmessageꢀwithꢀaꢀstateꢀchange.ꢀIfꢀoneꢀofꢀ
theseꢀmessagesꢀreportsꢀaꢀ‘U1’ꢀstateꢀforꢀaꢀregisteredꢀpointꢀ
thenꢀtheꢀdriverꢀprocessesꢀallꢀ‘ClearAll’ꢀMapꢀDescriptor’sꢀ
andꢀsetsꢀallꢀtheꢀassociatedꢀarrayꢀvaluesꢀtoꢀzero.ꢀ
AnꢀexampleꢀofꢀtheꢀuseꢀofꢀClearAllꢀisꢀprovidedꢀinꢀsectionꢀ
6.12ꢀexampleꢀ9.ꢀ
Passiveꢀ
Specifyꢀꢀcꢁpꢁsꢀꢀinꢀtheꢀ
MapꢀDescriptorꢀ(butꢀ
readꢀtheꢀnotesꢀonꢀtheꢀ
left)ꢀ
ClearAllꢀ
Generatesꢀaꢀwarmꢀrestartꢀmessage.ꢀ
Usedꢀtoꢀtestꢀtheꢀdriver.ꢀ
Usedꢀforꢀsimulationꢀ
only.ꢀ
Warm_Startꢀ
Usedꢀforꢀsimulationꢀ
only.ꢀ
Cold_Startꢀ Generatesꢀaꢀcoldꢀrestartꢀmessage.ꢀUsedꢀtoꢀtestꢀtheꢀdriver.ꢀ
ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 24 of 58
Appendix A.2.1.
Sim4100_Card Keyword
TheꢀFieldServerꢀwillꢀacceptꢀanyꢀpositiveꢀintegerꢀnumberꢀincludingꢀzero;ꢀhowever,ꢀnotꢀallꢀ
valuesꢀareꢀvalidꢀforꢀSimplexꢀdevices.ꢀꢀReferꢀtoꢀNoteꢀ(1).ꢀ
ꢀ
Manyꢀ commandsꢀ andꢀ outputꢀ messageꢀ containꢀ systemꢀ pointꢀ IDꢀ fields.ꢀ ꢀ Theseꢀ fieldsꢀ
reflectꢀtheꢀwayꢀaꢀ4100ꢀpointꢀ(local,ꢀexternal,ꢀreal,ꢀpseudo),ꢀisꢀreferredꢀto.ꢀꢀꢀ
ꢀ
Thereꢀ areꢀ twoꢀ basicꢀ formatsꢀ allowed,ꢀ addressꢀ formatꢀ <apoint>,ꢀ andꢀ symbolicꢀ formatꢀ
<spoint>.ꢀꢀꢀ
ꢀ
InꢀtheꢀSimplexꢀdeviceꢀtheꢀterminalꢀADDRESSꢀflagꢀisꢀsetꢀ(DEFAULT)ꢀsoꢀthatꢀ<apoint>ꢀisꢀ
alwaysꢀ usedꢀ inꢀ computerꢀ messages;ꢀ otherwise,ꢀ theꢀ symbolicꢀ formꢀ isꢀ used.ꢀ ꢀ Theꢀ
FieldServerꢀcannotꢀworkꢀwithꢀsymbolicꢀ(spoint)ꢀaddresses.ꢀ
ꢀ
Appendix A.2.2.
<apoint>
Formatꢀ<card>ꢁ<point>ꢁ<sub>ꢀ
Legend:ꢀ
<card>ꢀ
<point>ꢀ
<sub>ꢀ
Examples:ꢀ
0ꢁ6ꢁ6ꢀ
ꢀ
4100ꢀcard,ꢀpseudosꢀincluded,ꢀSeeꢀnoteꢀ(1)ꢀ
4100ꢀpointꢀ(sometimesꢀslot),ꢀSeeꢀnoteꢀ(2)ꢀ
4100ꢀsubꢁpointꢀ(sometimeꢀpoint),ꢀSeeꢀnoteꢀ(2)ꢀ
ꢀ
Masterꢀtroubleꢀpointꢀ(LCDꢀtrouble)ꢀ
Typicalꢀcardꢀstatusꢀpoint,ꢀcardꢀatꢀaddressꢀ5ꢀ
Pointꢀ1ꢀforꢀcardꢀatꢀaddressꢀ3ꢀ
5ꢁ0ꢁ1ꢀ
3ꢁ1ꢁ0ꢀ
ꢀ
Notes:ꢀ
(1)ꢀ
ꢀ
TheꢀfollowingꢀrangesꢀareꢀvalidꢀforꢀSimplexꢀDevices:ꢀ
ꢀ
Cardꢀaddressꢀ Cardꢀtypeꢀ
0ꢁ119ꢀ
128ꢁ143ꢀ
144ꢁ159ꢀ
160ꢁ175ꢀ
ꢀ
Physicalꢀ(Hardware)ꢀcardsꢀ
DigitalꢀPseudoꢀcardsꢀ
AnalogꢀPseudoꢀcardsꢀ
ListꢀPseudoꢀcardsꢀ
ꢀ
(2)ꢀ
Theꢀrangeꢀofꢀpointꢀandꢀsubꢁpointꢀfieldsꢀforꢀpointꢀaddressingꢀisꢀveryꢀsparseꢀandꢀ
dependsꢀonꢀtheꢀtypeꢀofꢀcardꢀatꢀthatꢀlocation.ꢀꢀContactꢀSimplexꢀTimeꢀCompanyꢀforꢀdetailsꢀ
onꢀpointꢀaddressꢀrangesꢀforꢀspecificꢀcards.ꢀ
Appendix A.2.3.
Sim4100_Point Keyword
TheꢀFieldServerꢀwillꢀacceptꢀanyꢀpositiveꢀintegerꢀnumberꢀincludingꢀzero;ꢀhowever,ꢀnotꢀallꢀ
theꢀ valuesꢀ areꢀ validꢀ forꢀ Simplexꢀ devicesꢀ ꢁꢀ seeꢀ Sectionsꢀ 6.3ꢀ andꢀ 6.4ꢀ forꢀ furtherꢀ
information.ꢀꢀ
Appendix A.2.4.
Sim4100_sub Keyword
TheꢀFieldServerꢀwillꢀacceptꢀanyꢀpositiveꢀintegerꢀnumberꢀincludingꢀzero;ꢀhowever,ꢀnotꢀallꢀ
theꢀ valuesꢀ areꢀ validꢀ forꢀ Simplexꢀ devicesꢀ ꢁꢀ seeꢀ Sectionsꢀ 6.3ꢀ andꢀ 6.4ꢀ forꢀ furtherꢀ
information.ꢀꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 25 of 58
Appendix A.3. How to use Data Arrays to map to/from Card-Point-Sub
addresses
SomeꢀcommandsꢀderiveꢀaꢀcardꢁpointꢁsubꢀaddressꢀbyꢀinspectingꢀaꢀFieldServerꢀDataꢀArray.ꢀꢀ
Othersꢀreceiveꢀdataꢀfromꢀaꢀdeviceꢀwithꢀaꢀcardꢁpointꢁsubꢀaddressꢀandꢀmodifyꢀtheꢀdataꢀinꢀanꢀ
arrayꢀ basedꢀ onꢀ theꢀ cardꢁpointꢁsubꢀ address.ꢀ ꢀ Thisꢀ sectionꢀ explainsꢀ howꢀ toꢀ makeꢀ theꢀ
connectionꢀbetweenꢀanꢀindexꢀintoꢀaꢀDataꢀArrayꢀandꢀaꢀcardꢁpointꢁsubꢀaddress.ꢀ
ꢀ
InꢀaꢀsimpleꢀworldꢀtheꢀDataꢀArrayꢀindexꢀwouldꢀbeꢀꢀ
ꢀ
ꢀ
Indexꢀ=ꢀcardꢀ*ꢀmaxꢀpointꢀperꢀcardꢀ*ꢀmaxꢀsubꢀpointꢀperꢀpointꢀ+ꢀpointꢀ*ꢀmaxꢀsubꢀpointꢀperꢀpointꢀ
+ꢀsubꢀꢀ
Whereꢀmaxꢀpointꢀperꢀcardꢀandꢀmaxꢀsubꢀpointꢀperꢀpointꢀcouldꢀbeꢀlargeꢀnumbers.ꢀ
ꢀ
AsꢀyouꢀcanꢀimagineꢀthisꢀwouldꢀrequireꢀhugeꢀsparseꢀDataꢀArrays.ꢀꢀToꢀreduceꢀtheꢀDataꢀArrayꢀ
sizeꢀ theꢀ FieldServerꢀ usesꢀ aꢀ mappingꢀ algorithmꢀ whichꢀ canꢀ beꢀ optimizedꢀ basedꢀ onꢀ theꢀ
addressesꢀ ofꢀ theꢀ Simplexꢀ devices.ꢀ Theꢀ mapꢀ isꢀ manipulatedꢀ byꢀ usingꢀ theꢀ
sim4100_card/point/subꢀparameterꢀvalues.ꢀ
ꢀ
Example:ꢀ
ꢀ
ConsiderꢀtheꢀfollowingꢀMapꢀDescriptorꢀfragment.ꢀ
…ꢀ,ꢀ sim4100_func,ꢀ sim4100_card,ꢀ sim4100_point,ꢀ sim4100_sub,ꢀ data_array_offsetꢀ
ꢀ
Xpoint,ꢀ
10,ꢀ
5,ꢀ
10,ꢀ
0ꢀ
ꢀ
Ifꢀdataꢀisꢀreceivedꢀforꢀpointꢀ<c>ꢁ<p>ꢁ<s>ꢀ=ꢀ9ꢁ0ꢁ0ꢀ
ThisꢀdataꢀwillꢀNOTꢀbeꢀprocessedꢀbecauseꢀtheꢀcardꢀnumberꢀdoesꢀnotꢀmatchꢀtheꢀvalueꢀofꢀtheꢀ
sim4100ꢁcardꢀ
ꢀ
Ifꢀdataꢀisꢀreceivedꢀforꢀpointꢀ<c>ꢁ<p>ꢁ<s>ꢀ=ꢀ10ꢁ20ꢁ0,ꢀhowever,ꢀtheꢀdataꢀwillꢀbeꢀprocessed.ꢀ
Theꢀarrayꢀlocationꢀisꢀderivedꢀusingꢀtheꢀfollowingꢀformulaꢀ(sim4100_subꢀisꢀtoꢀbeꢀreadꢀasꢀtheꢀ
“numberꢀofꢀsubꢁpointsꢀperꢀpoint”;ꢀsim4100_card’sꢀvalueꢀwillꢀbeꢀignored.)ꢀ
ꢀ
ꢀ
Locationꢀꢀ
=ꢀdata_array_offsetꢀ+ꢀꢀ<p>ꢀ*ꢀsim4100_subꢀ+ꢀ<s>ꢀ
=ꢀ0ꢀ+ꢀ20ꢀ*ꢀ10ꢀ+ꢀ0ꢀ=ꢀ200ꢀ
ꢀ
ꢀ
ꢀ
Appendix A.4. Simplex Point Status Data Format
WhenꢀaꢀpointꢀstatusꢀisꢀobtainedꢀtheꢀFieldServerꢀwillꢀwriteꢀoneꢀbyteꢀofꢀdataꢀtoꢀaꢀDataꢀArray.ꢀ
Theꢀbyteꢀwillꢀcontainꢀtheꢀfollowingꢀinformation.ꢀꢀBecauseꢀeachꢀpointꢀcanꢀreportꢀaꢀnumberꢀitꢀ
onlyꢀmakesꢀsenseꢀtoꢀuseꢀDataꢀArraysꢀthatꢀareꢀnotꢀbitꢀarrays.ꢀ
ꢀ
Bit
Identifier
Description
0ꢀ(FirstꢀBit)ꢀ
Fꢀ
Pꢀ
Sꢀ
Tꢀ
Uꢀ
Cꢀ
Dꢀ
Aꢀ
FireꢀAlarmꢀ
Priorityꢀ2ꢀ
Supervisoryꢀ
Troubleꢀ
Utilityꢀ
1ꢀ
2ꢀ
3ꢀ
4ꢀ
5ꢀ
6ꢀ
7ꢀ
Controlꢀ
Disableꢀ
Primaryꢀstateꢀ(basedꢀonꢀpointꢀtypeꢀꢁꢀFꢀifꢀsmokeꢀdetector,ꢀCꢀifꢀsignalꢀ
circuit,ꢀetc.)ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 26 of 58
Appendix A.5. Simulation of the Xpoint command
TheꢀfollowingꢀnotesꢀapplyꢀonlyꢀtoꢀFieldServerꢀTechnologiesꢀengineers.ꢀ
Theꢀ sim4100_func=xpointꢀ keywordꢀ isꢀ usedꢀ toꢀ parseꢀ unsolicitedꢀ pointꢀ statusꢀ changeꢀ
messagesꢀ sentꢀ byꢀ Simplexꢀ devices.ꢀ Forꢀ simulationꢀ purposesꢀ itꢀ aꢀ wrbcꢀ versionꢀ ofꢀ thisꢀ
functionꢀhasꢀbeenꢀimplementedꢀtoꢀtestꢀtheꢀresponseꢀparsingꢀabilityꢀofꢀtheꢀslaveꢀportionꢀofꢀtheꢀ
driver.ꢀ
Appendix A.6. Application Supervision Messages
Sectionꢀ7.2ꢀofꢀtheꢀSimplexꢀ4100ꢀprotocolꢀdescribesꢀunsolicitedꢀmessagesꢀfromꢀaꢀSimplexꢀ
device.ꢀꢀThisꢀsim4100_func=superꢀwrbcꢀcommandꢀisꢀusedꢀtoꢀtestꢀtheꢀdriver'sꢀabilityꢀtoꢀparseꢀ
theseꢀmessages.ꢀ
Theꢀ4100ꢀprotocolꢀsupportsꢀaꢀperiodicꢀapplicationꢀsupervisionꢀmessage.ꢀꢀThisꢀsupervisionꢀ
pollꢀisꢀperformedꢀifꢀtheꢀTERMINALꢀflagꢀPOLLꢀisꢀsetꢀ(COMPUTERꢀDEFAULT).ꢀꢀTheꢀobjectiveꢀ
ofꢀtheꢀsupervisionꢀpollꢀisꢀtwoꢁfold:ꢀ
•ꢀ Itꢀ isꢀ theꢀ onlyꢀ periodicꢀ messageꢀ thatꢀ canꢀ beꢀ expectedꢀ toꢀ beꢀ sentꢀ byꢀ theꢀ 4100,ꢀ thusꢀ
establishingꢀtheꢀbasisꢀforꢀsupervisingꢀtheꢀline.ꢀ
•ꢀ Toꢀensureꢀthatꢀallꢀlayersꢀofꢀtheꢀtwoꢀsystemsꢀareꢀoperatingꢀproperlyꢀandꢀableꢀtoꢀrespondꢀ
toꢀmessages.ꢀꢀForꢀexample,ꢀinꢀaꢀPCꢀimplementationꢀthatꢀusesꢀaꢀTerminateꢁandꢁStayꢁ
Residentꢀ(TSR)ꢀdeviceꢀdriverꢀtoꢀimplementꢀtheꢀprotocol,ꢀtheꢀanswerꢀtoꢀtheꢀsupervisionꢀ
pollꢀshouldꢀbeꢀdoneꢀinꢀaꢀwayꢀsuchꢀthatꢀifꢀtheꢀprogramꢀexitsꢀtoꢀDOS,ꢀtheꢀTSRꢀwillꢀnotꢀ
continueꢀtoꢀindicateꢀtoꢀtheꢀ4100ꢀthatꢀeverythingꢀisꢀOK,ꢀwhenꢀinꢀfact,ꢀtheꢀPCꢀwillꢀnotꢀbeꢀ
ableꢀtoꢀannunciateꢀanꢀalarm.ꢀ
Appendix A.7. Driver Stats
Appendix A.7.1.
How the Driver counts bytes and messages
received and transmitted.
"Ack"ꢀ messagesꢀ sent/receivedꢀ byꢀ theꢀ driverꢀ inꢀ responseꢀ toꢀ read/writeꢀ messagesꢀ areꢀ
NOTꢀcountedꢀasꢀmessages.ꢀꢀHowever,ꢀtheꢀsingleꢀbyteꢀproducedꢀbyꢀtheseꢀmessagesꢀisꢀ
includedꢀinꢀtheꢀbyteꢀcount.ꢀ
ꢀ
TheꢀdriverꢀdoesꢀnotꢀcountꢀDLLꢀlayerꢀmessagesꢀasꢀmessages.ꢀꢀ
ꢀ
TheꢀdriverꢀcountsꢀbytesꢀatꢀtheꢀDLLꢀlayer.ꢀTheꢀbyteꢀcountꢀincludesꢀtheꢀbytesꢀthatꢀwrapꢀ
applicationꢀlayerꢀmessages,ꢀacksꢀandꢀtheꢀportꢀsupervisionꢀandꢀresponsesꢀmessages.ꢀ
Theꢀ driverꢀ countsꢀ messagesꢀ atꢀ theꢀ applicationꢀ layer..ꢀ Thisꢀ meansꢀ thatꢀ ifꢀ youꢀ useꢀ
RUINETꢀtoꢀmonitorꢀtheꢀFieldServerꢀandꢀyouꢀviewꢀtheꢀMapꢀDescriptor’sꢀtheꢀbyteꢀcountꢀ
statsꢀwillꢀalwaysꢀbeꢀzero.ꢀ
ꢀ
SomeꢀMapꢀDescriptorsꢀrequireꢀdataꢀinꢀtheꢀDataꢀArraysꢀtoꢀtriggerꢀaꢀwriteꢀcommand.ꢀꢀAnꢀ
exampleꢀisꢀtheꢀ"Ack"ꢀcommand.ꢀꢀTheꢀdriverꢀdoesꢀnotꢀcountꢀoneꢀofꢀtheseꢀmessagesꢀasꢀ
beingꢀsentꢀuntilꢀtheꢀarrayꢀactuallyꢀtriggersꢀaꢀpollꢀtoꢀbeꢀsent.ꢀ
ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 27 of 58
Appendix A.7.2.
Driver Exposed Stats
Theꢀ driverꢀ isꢀ capableꢀ ofꢀ exposingꢀ statisticsꢀ aboutꢀ itsꢀ behaviorꢀ inꢀ aꢀ Dataꢀ Array.ꢀ ꢀ Itꢀ isꢀ
necessaryꢀtoꢀcreateꢀaꢀDataꢀArrayꢀwithꢀnameꢀsim4100ꢁstatsꢀasꢀperꢀtheꢀexampleꢀbelowꢀ
andꢀitꢀwillꢀbeꢀupdatedꢀbyꢀtheꢀdriver.ꢀꢀNoteꢀthatꢀtheꢀstatꢀnumberꢀcorrespondsꢀtoꢀtheꢀoffset.ꢀ
ꢀ
Takeꢀcareꢀnotꢀtoꢀpokeꢀanyꢀvaluesꢀintoꢀtheꢀ1stꢀ10ꢀelementsꢀofꢀthisꢀDataꢀArrayꢀ(offsetsꢀ0ꢀtoꢀ
9).ꢀꢀDoingꢀsoꢀwillꢀtriggerꢀinternalꢀdiagnosticsꢀandꢀmayꢀinterfereꢀwithꢀnormalꢀoperation.ꢀ
ꢀ
Aꢀdifferentꢀsetꢀofꢀstatsꢀisꢀmaintainedꢀforꢀeachꢀconnection.ꢀꢀEachꢀconnectionꢀusesꢀ100ꢀ
elementsꢀofꢀtheꢀdataꢀarray.ꢀꢀEnsureꢀtheꢀarrayꢀlengthꢀisꢀlargeꢀenoughꢀifꢀtheꢀportꢀnumberꢀisꢀ
large.ꢀ
ꢀ
Data_Arraysꢀ
Data_Array_Name,ꢀ
sim4100ꢁstatsꢀꢀꢀꢀꢀꢀꢀ,ꢀ
ꢀ
ꢀ
ꢀ
Data_Format,ꢀ
UINT16ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ,ꢀ
Data_Array_Lengthꢀ
1000ꢀ
Atꢀrevisionꢀ1.07aꢀofꢀtheꢀdriverꢀandꢀbefore,ꢀnoꢀstatsꢀhadꢀbeenꢀexposed.ꢀ
ꢀ
Stat
number
Stats
Description
TheꢀCardꢀinꢀcꢁpꢁsꢀfromꢀmostꢀ
recentꢀxpointꢀstoreꢀ
TheꢀPointꢀinꢀcꢁpꢁsꢀfromꢀmostꢀ
recentꢀxpointꢀstoreꢀ
TheꢀSubPointꢀinꢀcꢁpꢁsꢀfromꢀ
mostꢀrecentꢀxpointꢀstoreꢀ
TheꢀQualifierꢀfromꢀmostꢀrecentꢀ
xpointꢀstoreꢀ
10ꢀ
SIM4100_STAT_XPOINT_CARDꢀ
SIM4100_STAT_XPOINT_POINTꢀ
SIM4100_STAT_XPOINT_SUBꢀ
SIM4100_STAT_XPOINT_QUALIFIERꢀ
11ꢀ
12ꢀ
13ꢀ
TheꢀQualifierꢀfromꢀmostꢀrecentꢀ
xpointꢀstore,ꢀstoredꢀasꢀanꢀ
enumerationꢀ–ꢀSeeꢀNote1ꢀforꢀ
bitꢀstatesꢀ
Theꢀreportedꢀstateꢀfromꢀmostꢀ
recentꢀxpointꢀstore.ꢀStateꢀ
value:ꢀ0ꢀFALSE/Normalꢀ1ꢀ
TRUE/Abnormalꢀ
Theꢀreportedꢀackꢀstateꢀfromꢀ
mostꢀrecentꢀxpointꢀstore.ꢀAckꢀ
state:ꢀ*=needsꢀack,ꢀꢁ=ackedꢀ
(alwaysꢀ"ꢁ"ꢀforꢀUꢀorꢀCꢀstates)ꢀ
TheꢀTimeꢀfromꢀmostꢀrecentꢀ
xpointꢀstoreꢀ
TheꢀTimeꢀfromꢀmostꢀrecentꢀ
xpointꢀstoreꢀ
TheꢀTimeꢀfromꢀmostꢀrecentꢀ
xpointꢀstoreꢀ
TheꢀDateꢀfromꢀmostꢀrecentꢀ
xpointꢀstoreꢀ
TheꢀDateꢀfromꢀmostꢀrecentꢀ
xpointꢀstoreꢀ
14ꢀ
15ꢀ
16ꢀ
SIM4100_STAT_XPOINT_QUALIFIER_AS_ENUMꢀꢀ
SIM4100_STAT_XPOINT_STATEꢀ
SIM4100_STAT_XPOINT_ACK_STATEꢀ
17ꢀ
18ꢀ
19ꢀ
20ꢀ
21ꢀ
22ꢀ
SIM4100_STAT_XPOINT_HOURꢀ
SIM4100_STAT_XPOINT_MINꢀ
SIM4100_STAT_XPOINT_SECꢀ
SIM4100_STAT_XPOINT_DOWꢀ
SIM4100_STAT_XPOINT_DAYꢀ
SIM4100_STAT_XPOINT_MONTHꢀ
TheꢀDateꢀfromꢀmostꢀrecentꢀ
xpointꢀstoreꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 28 of 58
Stat
Stats
number
Description
TheꢀDateꢀfromꢀmostꢀrecentꢀ
xpointꢀstoreꢀ
23ꢀ
SIM4100_STAT_XPOINT_YEARꢀ
Aꢀsingleꢀpointꢀcouldꢀpotentiallyꢀ
beꢀactiveꢀinꢀmoreꢀthanꢀoneꢀ
stateꢀsimultaneously.ꢀTheꢀ
driverꢀtracksꢀtheꢀcombineꢀstateꢀ
byꢀbuildingꢀaꢀUINTꢀwhoseꢀbitsꢀ
indicateꢀtheꢀstate.ꢀThisꢀisꢀtheꢀ
comboꢀstateꢀbeforeꢀtheꢀupdate.ꢀ
SeeꢀNoteꢀ1ꢀforꢀbitꢀstates.ꢀ
Aꢀsingleꢀpointꢀcouldꢀpotentiallyꢀ
beꢀactiveꢀinꢀmoreꢀthanꢀoneꢀ
stateꢀsimultaneously.ꢀTheꢀ
driverꢀtracksꢀtheꢀcombineꢀstateꢀ
byꢀbuildingꢀaꢀUINTꢀwhoseꢀbitsꢀ
indicateꢀtheꢀstate.ꢀThisꢀisꢀtheꢀ
comboꢀstateꢀafterꢀtheꢀupdate.ꢀ
SeeꢀNoteꢀ1ꢀforꢀbitꢀstates.ꢀ
24ꢀ
SIM4100_STAT_XPOINT_COMBO_STATE_OLDꢀ
25ꢀ
SIM4100_STAT_XPOINT_COMBO_STATE_NEWꢀ
ꢀ
Noteꢀ1ꢀ–ꢀBitꢀStates.ꢀ
Qualifier:ꢀ
Enum=0ꢀQual=FꢀFireꢀalarmꢀstateꢀ
Enum=1ꢀQual=PꢀPriorityꢀ2ꢀalarmꢀstateꢀ
Enum=2ꢀQual=TꢀTroubleꢀstateꢀꢀ
Enum=3ꢀQual=SꢀSupervisoryꢀstateꢀ
Enum=4ꢀQual=UꢀUtilityꢀmonitor,ꢀdigital/analogꢀpseudoꢀstateꢀ
Enum=5ꢀQual=CꢀControlꢀstateꢀ(nonꢀpseudo)ꢀ
Enum=6ꢀQual=DꢀDisableꢀTroubleꢀstateꢀꢀ
ꢀ
Appendix A.8. SHOW Function Attributes and Attribute States
TheꢀShowꢀcommandꢀprovidesꢀanꢀASCIIꢀresponseꢀformattedꢀforꢀprinting.ꢀꢀTheꢀdriverꢀparsesꢀ
theseꢀmessagesꢀandꢀconvertsꢀtheꢀdataꢀtoꢀnumbersꢀwhichꢀcanꢀbeꢀsentꢀtoꢀupstreamꢀdevicesꢀ
usingꢀanotherꢀprotocol.ꢀꢀ
ꢀ
Theꢀdriverꢀperformsꢀtheꢀfollowingꢀtasksꢀinꢀanalyzingꢀtheꢀresponse.ꢀ
•ꢀ Onꢀaꢀlineꢀbyꢀlineꢀbasisꢀfromꢀtheꢀleft,ꢀitꢀsearchesꢀforꢀanꢀattributeꢀagainstꢀaꢀtableꢀofꢀattributeꢀ
strings.ꢀꢀIfꢀanꢀattributeꢀstringꢀisꢀfoundꢀinꢀtheꢀlineꢀthenꢀprocessingꢀcontinues.ꢀOtherwiseꢀ
theꢀlineꢀisꢀdiscarded.ꢀ
•ꢀ Theꢀattributeꢀnumberꢀisꢀrecorded.ꢀꢀItꢀwillꢀbeꢀusedꢀtoꢀdetermineꢀtheꢀarrayꢀlocationꢀwhereꢀ
theꢀattributeꢀstate/valueꢀwillꢀbeꢀstored.ꢀꢀ
•ꢀ Theꢀ attributeꢀ alsoꢀ determinesꢀ theꢀ state/valueꢀ extractionꢀ methodꢀ andꢀ attemptsꢀ toꢀ
determineꢀtheꢀattributeꢀstate/valueꢀusingꢀtheꢀappropriateꢀmethod.ꢀ
oꢀ Methodꢀ 1:ꢀ Theꢀ driverꢀ usesꢀ aꢀ tableꢀ ofꢀ attributeꢀ states,ꢀ comparingꢀ themꢀ toꢀ theꢀ
remainderꢀ ofꢀ theꢀ line.ꢀ ꢀ Ifꢀ thereꢀ isꢀ aꢀ matchꢀ theꢀ driverꢀ storesꢀ theꢀ valueꢀ ofꢀ theꢀ
attributeꢀstateꢀinꢀtheꢀarrayꢀlocationꢀdeterminedꢀbyꢀtheꢀattribute,ꢀ
oꢀ Methodꢀ2:ꢀTheꢀdriverꢀlooksꢀforꢀ(upꢀtoꢀthree)ꢀanalogꢀvaluesꢀseparatedꢀbyꢀforwardꢀ
slashes.ꢀ
oꢀ Methodꢀ3:ꢀTheꢀdriverꢀlooksꢀforꢀanalogꢀvaluesꢀprecededꢀbyꢀanꢀequalꢀsign.ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 29 of 58
•ꢀ Theꢀdriverꢀstoresꢀinꢀtheꢀfirstꢀarrayꢀlocationꢀtheꢀnumberꢀofꢀresponseꢀlinesꢀwhichꢀresultedꢀ
inꢀattributeꢀdataꢀbeingꢀstored.ꢀꢀThisꢀinformationꢀcanꢀbeꢀusedꢀforꢀtroubleꢀshooting.ꢀ
ꢀ
Theꢀ followingꢀ tableꢀ reportsꢀ theꢀ attributesꢀ thatꢀ theꢀ driverꢀ recognizes.ꢀ Thisꢀ listꢀ mayꢀ beꢀ
extendedꢀbyꢀchangingꢀtheꢀconfiguration.ꢀꢀIf,ꢀforꢀexample,ꢀtheꢀattributeꢀ‘ENABLEDꢀSTATE’ꢀisꢀ
recognizedꢀthenꢀtheꢀstateꢀofꢀthisꢀattributeꢀwillꢀbeꢀstoredꢀatꢀarrayꢀlocationꢀ6.ꢀ
ꢀ
Attribute
NotꢀDefinedꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
Array Position
0ꢀ
1ꢀ
2ꢀ
3ꢀ
4ꢀ
5ꢀ
6ꢀ
7ꢀ
Method
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ2ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ2ꢀ
ꢀ2ꢀ
ꢀ3ꢀ
ꢀ3ꢀ
ꢀ2ꢀ
ꢀ2ꢀ
ꢀ2ꢀ
ꢀ2ꢀ
ꢀ2ꢀ
ꢀ2ꢀ
ꢀ2ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ2ꢀ
ꢀ1ꢀ
ꢀ2ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ2ꢀ
PRIMARYꢀSTATUSꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
PHYSICALꢀSTATEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
RAWꢀSTATEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ACTIVEꢀSTATEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ARMEDꢀSTATEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ENABLEDꢀSTATEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
UNVERIFIEDꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
CURRENTꢀDEVICEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
DEVICEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
TESTꢀSTATEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
PRESENTꢀSENSITIVITYꢀSELECTED=ꢀꢀꢀꢀꢀ
PRESENTꢀSENSITIVITYꢀSELECTEDꢀ=ꢀꢀꢀꢀ
AVERAGEꢀVALUEꢀ=ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
AVERAGEꢀVALUE=ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
AVERAGEꢀ=ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
8ꢀ
9ꢀ
10ꢀ
11ꢀ
11ꢀ
14ꢀ
14ꢀ
14ꢀ
14ꢀ
14ꢀ
17ꢀ
17ꢀ
20ꢀ
20ꢀ
23ꢀ
24ꢀ
25ꢀ
26ꢀ
27ꢀ
30ꢀ
31ꢀ
32ꢀ
33ꢀ
34ꢀ
35ꢀ
36ꢀ
37ꢀ
38ꢀ
39ꢀ
40ꢀ
41ꢀ
42ꢀ
43ꢀ
44ꢀ
45ꢀ
AVERAGE=ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
AVERAGEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
VALUEꢀ=ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
VALUE=ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
PEAK=ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
PEAKꢀ=ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
TROUBLEꢀTHRESHOLDꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
OUTPUTꢀSTATEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
OUTPUTꢀSTATUSꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
DETECTORꢀSOUNDERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ALARMꢀTEMPERATUREꢀSELECTED=ꢀꢀꢀꢀꢀꢀꢀ
DETECTORꢀRELAYꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
TOTALꢀNUMBERꢀOFꢀTROUBLESꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
NODEꢀMISSINGꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
VERSIONꢀCONTROLꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
NODEꢀINITIALIZATIONꢀINꢀPROGRESSꢀꢀꢀ
SIMPLEXꢀSERVICEꢀMODEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
EARTHꢀGROUNDꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ACꢀPOWERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
BATTERYꢀLOW/DISCHARGEDꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
BATTERYꢀCHARGEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
SYSTEMꢀPSEUDOꢀSTATUSꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
NETWORKꢀCARDꢀSTATUSꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
CARDꢀTROUBLEꢀSTATUSꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
MISCELLANEOUSꢀSTATUSꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
RELAYꢀSTATUSꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
PRIORITYꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 30 of 58
Attribute
Array Position
Method
ꢀ1ꢀ
ꢀ2ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
ꢀ1ꢀ
CONTROLꢀSTATUSꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
CURRENTꢀ(AMPS)ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
CARDꢀMISSING/FAILEDꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
CORRECTꢀCARDꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
RSꢁ232ꢀInterfaceꢀꢀꢀꢀPORTꢀAꢀꢀꢀꢀꢀꢀꢀꢀꢀ
RSꢁ232ꢀInterfaceꢀꢀꢀꢀPORTꢀBꢀꢀꢀꢀꢀꢀꢀꢀꢀ
2120/RSꢁ232ꢀꢀPORTꢀBroadcastꢀFailꢀꢀꢀ
CARDꢀMISSING/FAILEDꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀ
46ꢀ
47ꢀ
48ꢀ
49ꢀ
40ꢀ
41ꢀ
42ꢀ
43ꢀ
Theꢀtableꢀbelowꢀreportsꢀtheꢀattributeꢀstatesꢀrecognizedꢀforꢀattributeꢀmethod=1.ꢀ
ꢀ
Attribute State
AUTOMATICꢀCONTROLꢀ
OUTPUTꢀNORMALꢀ
SELFꢀTESTꢀNORMALꢀ
CORRECTꢀDEVICEꢀ
PRIORITYꢀ15ꢀ
RANGEꢀNORMALꢀ
ALARMꢀ
SHORTꢀ
Value
1ꢀ
Attribute State
ARMEDꢀ
ENABLEDꢀ
ONꢁLINEꢀ
ENABLEDꢀ
NORMALꢀ
TROUBLEꢀ
OFFꢀ
Value
10ꢀ
11ꢀ
12ꢀ
13ꢀ
14ꢀ
15ꢀ
16ꢀ
17ꢀ
0ꢀ
2ꢀ
3ꢀ
4ꢀ
5ꢀ
6ꢀ
7ꢀ
8ꢀ
9ꢀ
ONꢀ
ꢀ
SHORTꢀ
ꢀ
Examples:
PHYSICALꢀSTATEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀSHORTꢀ
Driverꢀrecognizesꢀ‘PhysicalꢀState’ꢀasꢀattributeꢀ2ꢀandꢀusesꢀmethodꢀ1ꢀtoꢀevaluateꢀtheꢀrestꢀofꢀ
theꢀline.ꢀDriverꢀrecognizesꢀ‘Short’ꢀasꢀattributeꢀstateꢀwithꢀvalueꢀ8.ꢀTherefore,ꢀtheꢀdriverꢀstoresꢀ
theꢀnumberꢀ8ꢀatꢀlocationꢀ2ꢀinꢀtheꢀDataꢀArray.ꢀ
ꢀ
VALUE=77ꢀ/ꢀ0%ꢀOFꢀALARMꢀ/ꢀ1.0%ꢀSMOKEꢀ
Driverꢀrecognizesꢀ‘VALUE=’ꢀasꢀattributeꢀ17ꢀandꢀusesꢀmethodꢀ2ꢀtoꢀevaluateꢀtheꢀrestꢀofꢀtheꢀ
line.ꢀ Driverꢀ storesꢀ threeꢀ values;ꢀ 77,ꢀ 0ꢀ andꢀ 1.0ꢀ inꢀ threeꢀ consecutiveꢀ locationsꢀ startingꢀ atꢀ
locationꢀ17.ꢀꢀNoteꢀthatꢀthereꢀisꢀaꢀgapꢀbetweenꢀattributeꢀ17ꢀandꢀtheꢀnextꢀattributeꢀinꢀtheꢀtableꢀ
sufficientꢀforꢀstoringꢀupꢀtoꢀ3ꢀvalues.ꢀNoteꢀthatꢀaꢀslashꢀseparatesꢀtheꢀthreeꢀvalues.ꢀ
ꢀ
AVERAGEꢀVALUE=75ꢀꢀ/ꢀALARMꢀLEVEL=145ꢀ
Driverꢀrecognizesꢀ‘AVERAGEꢀVALUE’ꢀasꢀattributeꢀ14ꢀandꢀusesꢀmethodꢀ3ꢀtoꢀevaluateꢀtheꢀ
restꢀofꢀtheꢀline.ꢀDriverꢀstoresꢀtwoꢀvalues;ꢀ75ꢀandꢀ145ꢀinꢀtwoꢀconsecutiveꢀlocationsꢀstartingꢀatꢀ
locationꢀ14.ꢀNoteꢀthatꢀanꢀequalꢀsignꢀ‘=’ꢀprecedesꢀeachꢀnumericꢀvalue.ꢀꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 31 of 58
Appendix A.8.1.
Extending the List of Show Attributes
Youꢀcanꢀextendꢀtheꢀlistꢀofꢀattributesꢀandꢀattributeꢀstatesꢀthatꢀtheꢀdriverꢀrecognizesꢀbyꢀ
modifyingꢀtheꢀconfigurationꢀCSVꢀfile.ꢀ
Theꢀfollowingꢀexampleꢀaddsꢀthreeꢀattributesꢀandꢀ4ꢀattributeꢀstates.ꢀIfꢀaꢀdeviceꢀreportsꢀanꢀ
attributeꢀofꢀ‘LIGHTꢀSTATE’ꢀasꢀ‘BRIGHT’ꢀthenꢀtheꢀdriverꢀwillꢀloadꢀarrayꢀelementꢀ32ꢀwithꢀ
theꢀvalueꢀ41.ꢀ
ꢀ
Useꢀaꢀdigit.ꢀ
Keywordꢀ
startsꢀaꢀnewꢀ
AttributeꢀDefinitions.ꢀ
Theꢀnameꢀwillꢀbeꢀ
strippedꢀofꢀallꢀ
spacesꢀbetweenꢀtheꢀ
lastꢀcharacterꢀandꢀ
Theꢀthreeꢀ
methodsꢀareꢀ
describedꢀ
above.ꢀ
Whenꢀallocatingꢀ
offsets,ꢀbeꢀmindfulꢀ
ofꢀtheꢀoffsetsꢀ
sectionꢀofꢀtheꢀ
Protocolꢀmustꢀ
beꢀdefinedꢀonꢀ
everyꢀline.ꢀ
CSVꢀfile.ꢀ
alreadyꢀused.ꢀ
ꢀ
ꢀ
Driver_Tableꢀ
sim4100_Attr_Name,ꢀ sim4100_Attr_Offset,ꢀ sim4100_Attr_Method,ꢀ protocolꢀ
BROKENꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ,ꢀ
FIXEDꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ,ꢀ
LIGHTꢀSTATEꢀꢀꢀꢀꢀꢀ,ꢀ
30ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ,ꢀ
31ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ,ꢀ
32ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ,ꢀ
1ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ,ꢀ
1ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ,ꢀ
1ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ,ꢀ
sim4100ꢀ
sim4100ꢀ
sim4100ꢀ
Driver_Tableꢀ
ꢀ
ꢀ
sim4100_Attr_State_Name,ꢀ sim4100_Attr_State_value,ꢀ protocolꢀ
DIMꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ,ꢀ
BRIGHTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ,ꢀ
40ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ,ꢀ
41ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ,ꢀ
sim4100ꢀ
sim4100ꢀ
ꢀ
ꢀ
ꢀ
Useꢀvaluesꢀthatꢀareꢀnotꢀallocatedꢀtoꢀtheꢀ
preꢁdefinedꢀlistꢀofꢀstates.ꢀ
AttributeꢀStates.ꢀ
ꢀ
ꢀ
Appendix A.9. Synchronizing the FieldServer with the Panel
WhenꢀusingꢀtheꢀXpointꢀfunctionꢀtoꢀstoreꢀpointꢀstates,ꢀeachꢀtimeꢀtheꢀpanelꢀdoesꢀaꢀwarmꢁstartꢀ
itꢀsetsꢀallꢀpointꢀstatesꢀtoꢀnormalꢀandꢀthenꢀstartsꢀevaluatingꢀeveryꢀsingleꢀone.ꢀThus,ꢀafterꢀaꢀ
warmꢀstart,ꢀtheꢀFieldServerꢀwillꢀreceiveꢀXpointꢀmessagesꢀfromꢀtheꢀpanelꢀforꢀeveryꢀpointꢀnotꢀ
inꢀaꢀnormalꢀstate.ꢀThisꢀprovidesꢀoneꢀsynchronizationꢀmethod.ꢀTheꢀlimitationꢀofꢀthisꢀmethodꢀisꢀ
thatꢀtheꢀSimplexꢀpanelsꢀdoꢀnotꢀreportꢀwhenꢀaꢀpoint’sꢀstateꢀchangesꢀbackꢀtoꢀnormal.ꢀꢀThusꢀtoꢀ
maintainꢀtheꢀsynchronizationꢀtheꢀupstreamꢀdeviceꢀmustꢀclearꢀtheꢀpointꢀtoꢀzeroꢀonceꢀitꢀhasꢀ
readꢀitsꢀabnormalꢀstate,ꢀꢀi.e.ꢀTheꢀupstreamꢀdeviceꢀshouldꢀconsiderꢀtheꢀdataꢀreportedꢀbyꢀtheꢀ
Xpointꢀfunctionꢀasꢀlatchedꢀdata.ꢀ
ꢀ
Aꢀ secondꢀ methodꢀ isꢀ toꢀ connect/resetꢀ theꢀ FieldServerꢀ whenꢀ thereꢀ areꢀ noꢀ pointsꢀ inꢀ anꢀ
abnormalꢀstate.ꢀ
ꢀ
AꢀthirdꢀmethodꢀisꢀpollꢀpointꢀstatesꢀusingꢀtheꢀClistꢀfunctionꢀasꢀdescribedꢀinꢀAppendixꢀA.20.ꢀꢀ
ThisꢀwayꢀtheꢀFieldServerꢀstatesꢀwillꢀalwaysꢀbeꢀupdated.ꢀꢀPollingꢀisꢀslowꢀandꢀinꢀaꢀsystemꢀwithꢀ
manyꢀpointsꢀitꢀisꢀpossibleꢀthatꢀitꢀmayꢀtakeꢀseveralꢀminutesꢀtoꢀupdateꢀstatusꢀinformationꢀforꢀallꢀ
points.ꢀꢀThusꢀcombiningꢀthisꢀmethodꢀwithꢀtheꢀuseꢀofꢀXpointꢀMapꢀDescriptorsꢀgivesꢀtheꢀbestꢀ
ofꢀbothꢀworlds.ꢀꢀWhenꢀaꢀpointꢀchangesꢀtoꢀ‘not’ꢀnormal,ꢀthenꢀtheꢀFieldServerꢀgetsꢀtheꢀstateꢀ
changeꢀ fromꢀ theꢀ Xpointꢀ functionꢀ immediatelyꢀ andꢀ atꢀ theꢀ sameꢀ timeꢀ synchronizationꢀ isꢀ
assuredꢀbyꢀtheꢀcontinuousꢀpolling.ꢀ
ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 32 of 58
Aꢀfourthꢀmethodꢀisꢀprovidedꢀtoo.ꢀꢀThisꢀmethodꢀallowsꢀaꢀrangeꢀofꢀaꢀdataꢀarrayꢀtoꢀbeꢀsetꢀtoꢀ
zeroꢀwhenꢀaꢀuserꢀspecifiedꢀpointꢀreportsꢀaꢀnormalꢀstate.ꢀꢀReferꢀtoꢀAppendixꢀA.17ꢀforꢀmoreꢀ
information.ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 40 of 58
Array Position
Attribute
Value
Filled In5 Note
0ꢀ
NotꢀDefinedꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
PRIMARYꢀSTATUSꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
PHYSICALꢀSTATEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
RAWꢀSTATEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ACTIVEꢀSTATEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ARMEDꢀSTATEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ENABLEDꢀSTATEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
UNVERIFIEDꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
CURRENTꢀDEVICEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
DEVICEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
TESTꢀSTATEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
PRESENTꢀSENSITIVITYꢀSELECTEDꢀ
AVERAGEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
VALUEꢀ
10ꢀ
1ꢀ
1ꢀ
ꢀ
!ꢀ
#ꢀ
~ꢀ
ꢀ
1ꢀ
14ꢀ(Normal)ꢀ
2ꢀ
ꢀ
3ꢀ
ꢀ
ꢀ
4ꢀ
ꢀ
ꢀ
ꢀ
5ꢀ
ꢀ
ꢀ
ꢀ
6ꢀ
11ꢀ(Enabled)ꢀ
1ꢀ
1ꢀ
1ꢀ
1ꢀ
1ꢀ
ꢀ
ꢀ
7ꢀ
0ꢀ
ꢀ
8ꢀ
4ꢀ(CorrectꢀDevice)ꢀ
ꢀ
9ꢀ
12ꢀ(On_Line)ꢀ
ꢀ
10ꢀ
11ꢀ
14ꢀ
17ꢀ
18ꢀ
19ꢀ
20ꢀ
21ꢀ
22ꢀ
23ꢀ
24ꢀ
25ꢀ
26ꢀ
27ꢀ
30ꢀ
3ꢀ(Selfꢀtestꢀnormal)ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
0ꢀ
1ꢀ
1ꢀ
ꢀ
ꢀ
ꢀ
ꢁ41ꢀ
ꢀ
ꢀ
ꢀ
*ꢀ
ꢀ
PEAKꢀ
0ꢀ
1ꢀ
1ꢀ
ꢀ
ꢀ
ꢁ41ꢀ
ꢀ
ꢀ
ꢀ
*ꢀ
ꢀ
TROUBLEꢀTHRESHOLDꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
OUTPUTꢀSTATEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
OUTPUTꢀSTATUSꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
DETECTORꢀSOUNDERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ALARMꢀTEMPERATUREꢀSELECTED=ꢀꢀꢀꢀꢀꢀꢀ
DETECTORꢀRELAYꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
6ꢀ(RangeꢀNormal)ꢀ
1ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
135ꢀ
ꢀ
ꢀ
ꢀ
1ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Notes:
!ꢀꢀTheꢀvalueꢀ10ꢀrepresentsꢀtheꢀcountꢀofꢀtheꢀnumberꢀofꢀattributesꢀthatꢀwereꢀextractedꢀfromꢀ
theꢀ response.ꢀ Itꢀ isꢀ notꢀ equalꢀ toꢀ theꢀ numberꢀ ofꢀ arrayꢀ locationsꢀ filledꢀ inꢀ becauseꢀ someꢀ
attributesꢀ(e.g.ꢀValue)ꢀresultꢀinꢀmoreꢀthanꢀoneꢀarrayꢀlocationꢀbeingꢀupdated.ꢀ
~ꢀTheꢀunꢁfilledꢁinꢀlocationsꢀareꢀnotꢀupdatedꢀbyꢀtheꢀdriverꢀwhenꢀthisꢀresponseꢀisꢀanalysedꢀ
becauseꢀ theꢀ attributesꢀ correspondingꢀ toꢀ theseꢀ locationsꢀ wereꢀ notꢀ reportedꢀ inꢀ theꢀ
responseꢀtoꢀtheꢀquery.ꢀ
*ꢀRoomꢀforꢀupꢀtwoꢀthreeꢀnumbersꢀforꢀattributesꢀlikeꢀvalue,ꢀpeakꢀbutꢀinꢀthisꢀcaseꢀonlyꢀtwoꢀ
valuesꢀareꢀrelevantꢀforꢀthisꢀdevice.ꢀ
ꢀ
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ ꢀꢀꢀꢀꢀꢀꢀ
5ꢀLocationsꢀmarkedꢀwithꢀaꢀ1ꢀareꢀupdatedꢀwhenꢀtheꢀdriverꢀanalysesꢀthisꢀresponseꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 41 of 58
Appendix A.20. Using Clist to Write-Through and Store point status from
Unsolicited Messages
Fromꢀversionꢀ1.05ꢀonꢀtheꢀfunctionalityꢀofꢀtheꢀ‘clist’ꢀMapꢀDescriptor’sꢀhasꢀbeenꢀenhanced.ꢀ
ꢀ
ꢀ
Theꢀ‘Clist’ꢀMapꢀDescriptorsꢀcanꢀꢀ
•ꢀ Readꢀaꢀpoint’sꢀstatusꢀꢀ
•ꢀ WriteꢀtoꢀaꢀpointꢀwhenꢀaꢀWriteꢁThroughꢀisꢀactivatedꢀꢀ
•ꢀ Storeꢀtheꢀpointꢀstatusꢀwhenꢀanꢀ‘xpoint’ꢀunsolicitedꢀmessageꢀisꢀreceivedꢀfromꢀtheꢀpanel.ꢀ
ꢀ
AꢀWriteꢁThroughꢀoccursꢀwhenꢀaꢀDataꢀArrayꢀvalueꢀthatꢀisꢀnormallyꢀupdatedꢀbyꢀaꢀreadꢀ(rdbc)ꢀ
MapꢀDescriptorꢀisꢀupdatedꢀbyꢀsomeꢀotherꢀdriverꢀorꢀbyꢀusingꢀtheꢀRuinetꢀapplication.ꢀꢀ
InꢀthisꢀcaseꢀtheꢀupdatedꢀvalueꢀisꢀwrittenꢀthroughꢀtheꢀreadꢀMapꢀDescriptorꢀandꢀtheꢀSimplexꢀ
4100ꢀdriverꢀwritesꢀtheꢀupdatedꢀvalueꢀtoꢀtheꢀpanel.ꢀꢀTheꢀvalueꢀisꢀwrittenꢀonceꢀonlyꢀeachꢀtimeꢀ
thatꢀtheꢀDataꢀArrayꢀelementꢀisꢀupdatedꢀexceptꢀwhenꢀtheꢀvalueꢀisꢀupdatedꢀbyꢀtheꢀresponseꢀtoꢀ
theꢀreadꢀorꢀifꢀtheꢀpointꢀstatusꢀisꢀupdatedꢀwhenꢀanꢀunsolicitedꢀmessageꢀisꢀreceivedꢀfromꢀtheꢀ
panel.ꢀ
Ensureꢀthat:ꢀ
•ꢀ Theꢀpointꢀisꢀnotꢀaꢀreadꢀonlyꢀꢀpointꢀ
•ꢀ TheꢀPanel’sꢀaccessꢀlevelꢀhasꢀbeenꢀsetꢀappropriately.ꢀ
ꢀ
Whenꢀanꢀunsolicitedꢀmessageꢀisꢀreceivedꢀfromꢀtheꢀpanelꢀitꢀwouldꢀnormallyꢀbeꢀstoredꢀusingꢀaꢀ
MapꢀDescriptorꢀwithꢀtheꢀ‘xpoint’ꢀfunction.ꢀ(Seeꢀsectionꢀ4.5.6)ꢀHowever,ꢀifꢀyouꢀareꢀpollingꢀforꢀtheꢀ
statusꢀ ofꢀ thatꢀ pointꢀ usingꢀ aꢀ ‘Clist’ꢀ Mapꢀ Descriptorꢀ andꢀ ifꢀ thatꢀ Mapꢀ Descriptorꢀ hasꢀ
‘Store_Unsolicited’ꢀsetꢀtoꢀyesꢀthenꢀyouꢀmustꢀomitꢀtheꢀ‘xpoint’ꢀMapꢀDescriptorꢀasꢀtheꢀ‘Clist’ꢀMapꢀ
Descriptorꢀcanꢀbeꢀusedꢀtoꢀstoreꢀtheꢀpointꢀstatusꢀwhenꢀitꢀisꢀupdatedꢀwithꢀanꢀunsolicitedꢀmessage.ꢀ
IfꢀyouꢀhaveꢀbothꢀMapꢀDescriptor’sꢀdefinedꢀthenꢀtheꢀresultꢀwillꢀbeꢀunpredictable.ꢀ
ꢀ
AꢀwriteꢀcommandꢀcanꢀbeꢀsentꢀtoꢀaꢀSimplexꢀpanelꢀinꢀoneꢀofꢀtwoꢀformats:ꢀ
1)ꢀ SETꢀcꢁpꢁsꢀON/OFFꢀ(default)ꢀ
2)ꢀ SETꢀcꢁpꢁsꢀvalueꢀ
ꢀ
Useꢀtheꢀsim4100_WriteThruꢀparameterꢀinꢀtheꢀCSVꢀtoꢀchangeꢀtoꢀtheꢀ2ndꢀformat.ꢀ
ꢀ
Evenꢀifꢀyouꢀareꢀwritingꢀtoꢀanꢀanalogꢀpseudoꢀpointꢀusingꢀformatꢀ1ꢀisꢀsuitableꢀbecauseꢀbyꢀenablingꢀ
theꢀpointꢀyouꢀforceꢀitꢀtoꢀtakeꢀitsꢀintrinsicꢀvalue.ꢀByꢀsettingꢀtheꢀpointꢀoffꢀyouꢀareꢀsettingꢀitsꢀvalueꢀtoꢀ
zero.ꢀꢀ
ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Appendix B. Troubleshooting Tips
Page 42 of 58
Appendix B.1. Address Errors
IfꢀtheꢀdriverꢀproducesꢀBAD_ADDRESSꢀstatsꢀthenꢀdoꢀtheꢀfollowingꢀꢀ
•ꢀ Readꢀtheꢀnotesꢀonꢀprocessingꢀerrors.ꢀYouꢀcanꢀseeꢀtheꢀlastꢀerrorꢀresponseꢀandꢀaꢀreportꢀ
ofꢀtheꢀMD'sꢀwhichꢀreceivedꢀtheꢀerrorꢀresponseꢀinꢀtheꢀerrorꢀarray.ꢀꢀ
•ꢀ Alternatively,ꢀtakeꢀaꢀlog,ꢀopenꢀtheꢀASCIIꢀversionꢀofꢀtheꢀlogꢀandꢀlookꢀforꢀerrorꢀmessages.ꢀ
Errorꢀ2ꢀisꢀtheꢀresponseꢀsentꢀbyꢀtheꢀpanelꢀwhenꢀitꢀisꢀpolledꢀforꢀaꢀpointꢀthatꢀdoesn’tꢀexist.ꢀ
FindꢀtheꢀErrorꢀ#2'sꢀnꢀtheꢀlog.ꢀNowꢀlookꢀatꢀtheꢀlineꢀwhichꢀprecedesꢀtheꢀerror.ꢀItꢀisꢀtheꢀpoll.ꢀ
Lookꢀtoꢀseeꢀwhichꢀpointꢀinꢀbeingꢀpolled.ꢀꢀNowꢀyouꢀknowꢀtheꢀcꢁpꢁsꢀofꢀtheꢀinvalidꢀpoint,ꢀeditꢀ
theꢀconfigurationꢀandꢀremoveꢀtheꢀMDꢀwhichꢀpollsꢀforꢀdataꢀatꢀthatꢀpoint.ꢀWhenꢀyouꢀhaveꢀ
finishedꢀ editingꢀtheꢀ configuration,ꢀ downloadꢀ theꢀmodifiedꢀfileꢀ andꢀresetꢀtheꢀ FSꢀforꢀ theꢀ
changesꢀtoꢀtakeꢀeffect.ꢀ
ꢀ
Appendix B.2. Driver Limitations
•ꢀ OtherꢀthanꢀbeingꢀableꢀtoꢀwriteꢀthroughꢀaꢀMapꢀDescriptorꢀwhereꢀtheꢀsim4100_func=’clist’ꢀ,ꢀ
writeꢀthroughsꢀareꢀnotꢀsupportedꢀbyꢀthisꢀdriver.ꢀꢀ
•ꢀ Portꢀexpansionꢀisꢀnotꢀsupported.ꢀ
ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 43 of 58
Appendix B.3. Resolving Network Addresses above 255
TheꢀStandardꢀformatꢀforꢀaddressingꢀaꢀsimplexꢀpointꢀisꢀcꢁpꢁsꢀ(CardꢁPointꢁSubpoint).ꢀꢀEachꢀofꢀ
theseꢀcomponentsꢀinꢀtheꢀaddressꢀsupportsꢀaꢀmaximumꢀvalueꢀofꢀ255.ꢀꢀHowever,ꢀwhenꢀusingꢀ
anꢀ NDUꢀ (Networkꢀ Displayꢀ Unit),ꢀ addressesꢀ mayꢀ beꢀ suppliedꢀ inꢀ aꢀ CardꢁAddressꢀ formatꢀ
whereꢀtheꢀaddressꢀvalueꢀcouldꢀbeꢀsubstantiallyꢀlargerꢀthanꢀ255.ꢀꢀInꢀtheseꢀapplicationsꢀitꢀwillꢀ
beꢀnecessaryꢀtoꢀconvertꢀtheꢀCardꢁAddressꢀformatꢀintoꢀcꢁpꢁsꢀformatꢀbeforeꢀconfiguringꢀtheꢀ
pointsꢀinꢀtheꢀFieldServer.ꢀ
ꢀ
Theꢀformulaꢀusedꢀtoꢀconvertꢀbetweenꢀtheꢀtwoꢀformatsꢀisꢀasꢀfollows:ꢀ
ꢀ
Cardꢀisꢀtheꢀsameꢀforꢀbothꢀformats.ꢀ
NetworkꢀAddressꢀ=ꢀ((Pointꢁ1)*256)ꢀ+ꢀSubꢁPointꢀ+ꢀ1ꢀ
ꢀ
Thisꢀconversionꢀprocedureꢀisꢀbestꢀillustratedꢀbyꢀmeansꢀofꢀanꢀexample:ꢀ
ꢀ
Example:
Card–Addressꢀpointꢀsuppliedꢀ=ꢀ5ꢁ2936ꢀ
ꢀ
Fromꢀthisꢀweꢀdeduceꢀtheꢀcardꢀnumberꢀtoꢀbeꢀ5.ꢀTheꢀnextꢀstepꢀisꢀtoꢀbreakꢀtheꢀaddressꢀintoꢀ
multiplesꢀ ofꢀ 256ꢀ inꢀ orderꢀ toꢀ determineꢀ pointꢀ andꢀ subꢁpoint.ꢀ Sinceꢀ thisꢀ isꢀ alsoꢀ aꢀ hexꢀ
denominatedꢀcalculation,ꢀanꢀeasyꢀwayꢀtoꢀdoꢀthisꢀisꢀtoꢀconvertꢀtheꢀvalueꢀtoꢀHex:ꢀ
ꢀ
2936ꢀ=ꢀ0xB78ꢀ
ꢀ
Now,ꢀbreakꢀoutꢀtheꢀlastꢀtwoꢀhexꢀnumbersꢀforꢀsubꢁpointꢀportion,ꢀandꢀuseꢀtheꢀrestꢀforꢀpointꢀ
address.ꢀSoꢀweꢀget:ꢀ
ꢀ
0xBꢀ=ꢀ11ꢀ=ꢀ(Pointꢁ1)ꢀ
0x78ꢀ=ꢀ120ꢀ=ꢀSubꢁPointꢀ+ꢀ1ꢀ
ꢀ
Solvingꢀthisꢀequation,ꢀweꢀget:ꢀ
ꢀ
Pointꢀ=ꢀ12ꢀ
SubꢁPointꢀ=ꢀ119ꢀ
ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 44 of 58
Appendix C. Error Messages
Error Message
Troubleshooting Tip
Theꢀcardꢁpointꢁsubꢀisꢀbeingꢀusedꢀtoꢀderiveꢀanꢀarrayꢀ
offset.ꢀTheꢀcalculationꢀrequiresꢀdivisionꢀbyꢀtheꢀpointꢀ
&ꢀtheꢀsubꢀandꢀoneꢀorꢀbothꢀofꢀtheseꢀvaluesꢀareꢀzero.ꢀ
Sim4100:#1ꢀ
invalidꢀforꢀack.ꢀReadꢀmanual.ꢀ
<card><point><sub>ꢀ
Sim4100:#2ꢀRTSꢀhasꢀbeenꢀassertedꢀforꢀ IfꢀRTSꢁCTSꢀhandshakingꢀhasꢀbeenꢀusedꢀthenꢀthisꢀ
tooꢀ long.ꢀ Extendꢀ timer,ꢀ checkꢀ cableꢀ messageꢀ isꢀ producedꢀ ifꢀ theꢀ driverꢀ findsꢀ thatꢀ theꢀ
usesꢀRTS/CTSꢀorꢀreconfigꢀ4100ꢀdeviceꢀ RTSꢀhasꢀbeenꢀassertedꢀbyꢀtheꢀslaveꢀdeviceꢀforꢀtooꢀ
toꢀsuppressꢀhardwareꢀhandshakingꢀ
Sim4100:#3ꢀ sim4100_chan_init()ꢀ Initꢀ
withꢀnullꢀchan.ꢀ
long.ꢀTheꢀtimeoutꢀisꢀhardꢀcodedꢀatꢀ2.0s.ꢀ
RequiresꢀsupportꢀfromꢀFieldServerꢀTechnologies.ꢀ
Theꢀ driverꢀ hasꢀ foundꢀ aꢀ valueꢀ forꢀ aꢀ sim4100_funcꢀ
Sim4100:#4ꢀUnknownꢀsim4100_funcꢀinꢀ keywordꢀthatꢀitꢀdoesꢀnotꢀrecognize.ꢀCheckꢀtheꢀCSVꢀ
csvꢀ<nnn>ꢀ
fileꢀandꢀreadꢀAppendixꢀA.2ꢀofꢀthisꢀmanualꢀforꢀaꢀlistꢀ
ofꢀlegalꢀkeywords.ꢀ
Theꢀsim4100_funcꢀkeywordꢀhasꢀbeenꢀassignedꢀtheꢀ
valueꢀ 'ack'ꢀ butꢀ aꢀ cardꢁpointꢁsubꢀ hasꢀ notꢀ beenꢀ
specified.ꢀ Itꢀ wouldꢀ beꢀ betterꢀ toꢀ useꢀ theꢀ ackallꢀ
functionꢀinstead.ꢀ
Sim4100:#5ꢀUseꢀAckallꢀfunction.ꢀ
Sim4100:#6ꢀ ack/ackall/seta/setdꢀ mustꢀ Youꢀ cannotꢀ useꢀ theꢀ rdbcꢀ functionꢀ withꢀ theseꢀ
beꢀaꢀwrite.ꢀ
keywords.ꢀUseꢀaꢀwrbcꢀinstead.ꢀ
Youꢀ cannotꢀ useꢀ theseꢀ keywordsꢀ atꢀ theꢀ presentꢀ
time.ꢀ Ifꢀ youꢀ requireꢀ oneꢀ ofꢀ theseꢀ functionsꢀ
implementedꢀcallꢀFieldServerꢀTechnologies.ꢀ
Sim4100:#7ꢀ disable/restart/listꢀ notꢀ
implementedꢀ
Sim4100:#8ꢀ Func=Clistall/Clist,ꢀ wrbcꢀ
notꢀallowedꢀ
Theseꢀkeywordsꢀmustꢀbeꢀusedꢀwithꢀaꢀrdbcꢀinstead.ꢀ
Sim4100:#9ꢀ Writeꢀ ackꢀ wasꢀ notꢀ Pleaseꢀ reportꢀ thisꢀ errorꢀ toꢀ FieldServerꢀ
expected.ꢀ
Technologies.ꢀ
Sim4100:#10ꢀ Invalidꢀ pointꢀ statusꢀ
<s><v><a>=(Hex)<%x><%x><%x>ꢀ
<%c><%c><%c>ꢀ
Pleaseꢀ reportꢀ hisꢀ messageꢀ toꢀ FieldServerꢀ
Technologiesꢀnotingꢀtheꢀvaluesꢀinꢀbraces.ꢀ
Sim4100:#11.ꢀ Error.ꢀ Arrayꢀ tooꢀ short.ꢀ
rqd=ꢀ %d(ꢀ max=ꢀ %d)ꢀ act=ꢀ %d.ꢀ
MapDesc=ꢀ <%s>ꢀ Dataꢀ Abandoned!ꢀ
Subsequentꢀmsgsꢀsuppressed!ꢀ
Sim4100:#12ꢀError.ꢀ
CheckꢀtheꢀCSVꢀfileꢀDataꢀArrayꢀlengths.ꢀ
Incomingꢀdataꢀisꢀbeingꢀabandoned.ꢀ
Checkꢀ theꢀ CSVꢀ file;ꢀ thereꢀ wasꢀ noꢀ matchingꢀ Mapꢀ
Descriptorꢀforꢀaꢀmessage.ꢀ
Subsequentꢀmessageꢀsupressed!ꢀ
Sim4100:#13ꢀ FYI.ꢀ Loginꢀ Functionꢀ notꢀ Pleaseꢀ contactꢀ FieldServerꢀ Technologiesꢀ ifꢀ youꢀ
Implemented.ꢀ wouldꢀlikeꢀthisꢀfeatureꢀimplemented.ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Error Message
Page 45 of 58
Troubleshooting Tip
Aꢀwriteꢀthruꢀisꢀdefinedꢀasꢀfollows.ꢀTheꢀFieldServerꢀ
readsꢀ dataꢀ fromꢀ aꢀ deviceꢀ andꢀ storesꢀ itꢀ inꢀ aꢀ Dataꢀ
Array.ꢀꢀIfꢀaꢀremoteꢀdeviceꢀchangesꢀtheꢀvalueꢀinꢀthatꢀ
DataꢀArray,ꢀtheꢀFieldServerꢀwillꢀwriteꢀtheꢀnewꢀvalueꢀ
toꢀtheꢀdeviceꢀthatꢀisꢀbeingꢀread.ꢀꢀThisꢀdriverꢀdoesꢀ
notꢀ permitꢀ writeꢀ thru'sꢀ exceptꢀ whenꢀ theꢀ dataꢀ isꢀ
beingꢀupdatedꢀusingꢀCLIST.ꢀꢀReferꢀalsoꢀtoꢀSectionsꢀ
4.5.4,ꢀ4.5.6ꢀandꢀAppendixꢀA.20.ꢀꢀInꢀversionsꢀofꢀtheꢀ
driverꢀupꢀtoꢀandꢀincludingꢀ1.07aꢀaꢀpanicꢀisꢀproducedꢀ
whenꢀ thisꢀ messageꢀ isꢀ printed.ꢀ ꢀ Theꢀ messageꢀ isꢀ
printedꢀ toꢀ aꢀ maximumꢀ ofꢀ 10ꢀ timesꢀ andꢀ thenꢀ
suppressed.ꢀ
Sim4100:#14ꢀMD=%sꢀAddr=%dꢀ
SIM4100:#15ꢀ
abandoned.ꢀNoꢀMapꢀDesc.ꢀ
FYI.ꢀ
Incomingꢀ Checkꢀ theꢀ CSVꢀ file;ꢀ thereꢀ wasꢀ noꢀ matchingꢀ Mapꢀ
Descriptorꢀforꢀaꢀmessage.ꢀ
Ifꢀtheꢀserverꢀcan’tꢀfindꢀaꢀmatchingꢀMDꢀ(i.e.ꢀtheꢀpointꢀ
beingꢀ polledꢀ forꢀ doesn’tꢀ exist)ꢀ thenꢀ theꢀ driverꢀ
respondsꢀwithꢀSimplexꢀErrorꢀ#2.ꢀ
SIM4100:#16ꢀ FYI.ꢀ Noꢀ Mapꢀ Desc.ꢀ
RespondꢀwithꢀError.ꢀ
Checkꢀ theꢀ driverꢀ manualꢀ andꢀ Simplexꢀ Userꢀ
Manuals.ꢀ ꢀ Thereꢀ isꢀ noꢀ driverꢀ responseꢀ toꢀ theꢀ
messageꢀreceived.ꢀ
SIM4100:#17ꢀ
Abandoned.ꢀNoꢀData.ꢀ
FYI.ꢀ
Incomingꢀ
SIM4100:#18ꢀ
Abandoned.ꢀ(%d)ꢀ
FYI.ꢀ
Incomingꢀ Pleaseꢀ reportꢀ hisꢀ messageꢀ toꢀ FieldServerꢀ
Technologiesꢀnotingꢀtheꢀvaluesꢀinꢀbraces.ꢀ
Noꢀ correctiveꢀ actionꢀ isꢀ requiredꢀ onꢀ yourꢀ part.ꢀTheꢀ
messageꢀisꢀprintedꢀforꢀyourꢀinformationꢀonly.ꢀ
ꢀ
Messageꢀ‘a’ꢀisꢀprintedꢀwhenꢀ versionꢀ9ꢀfirmwareꢀisꢀ
foundꢀinꢀtheꢀpanel.ꢀ
Messageꢀ‘b’ꢀisꢀprintedꢀwhenꢀversionꢀ10ꢀfirmwareꢀisꢀ
foundꢀinꢀtheꢀpanel.ꢀ
Sim4100:#19aꢀ FYI.ꢀ Sim4100ꢀ Firmwareꢀ
foundꢀ(%.2f)ꢀ
Messageꢀ‘b’ꢀisꢀprintedꢀwhenꢀversionꢀ11ꢀfirmwareꢀisꢀ
foundꢀinꢀtheꢀpanel.ꢀ
Theꢀ firmwareꢀ versionꢀ foundꢀ isꢀ notꢀ oneꢀ thatꢀ theꢀ
driverꢀ explicitlyꢀ supports.ꢀ Thisꢀ doesꢀ notꢀ meanꢀ theꢀ
driverꢀwillꢀnotꢀworkꢀbutꢀifꢀaꢀfeatureꢀofꢀtheꢀdriverꢀisn’tꢀ
workingꢀcorrectlyꢀknowingꢀthatꢀtheꢀfirmwareꢀversionꢀ
isꢀ notꢀ supportedꢀ mayꢀ helpꢀ diagnoseꢀ theꢀ problemꢀ
Sim4100:#19dꢀ FYI.ꢀ Panelꢀ Firmwareꢀ moreꢀeasily.ꢀ
Revꢀ%.2fꢀmayꢀbeꢀincompatible.ꢀ
ꢀ
Noꢀ correctiveꢀ actionꢀ isꢀ requiredꢀ onꢀ yourꢀ part.ꢀ Ifꢀ
however,ꢀ someꢀ youꢀ suspectꢀ thatꢀ theꢀ driverꢀ isꢀ notꢀ
operatingꢀcorrectlyꢀitꢀisꢀimportantꢀthatꢀyouꢀmentionꢀ
seeingꢀ thisꢀ messageꢀ inꢀ theꢀ Errorꢀ Bufferꢀ whenꢀ
reportingꢀtheꢀproblem.ꢀꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Error Message
Page 46 of 58
Troubleshooting Tip
Theꢀ formatꢀ ofꢀ theꢀ firmwareꢀ versionꢀ informationꢀ
couldꢀnotꢀbeꢀinterpretedꢀcorrectly.ꢀThisꢀmayꢀmeanꢀ
thatꢀyourꢀpanelꢀhasꢀaꢀfirmwareꢀversionꢀthatꢀisꢀ notꢀ
oneꢀthatꢀtheꢀdriverꢀexplicitlyꢀsupports.ꢀThisꢀdoesꢀnotꢀ
meanꢀtheꢀdriverꢀwillꢀnotꢀworkꢀbutꢀifꢀaꢀfeatureꢀofꢀtheꢀ
driverꢀ isn’tꢀ workingꢀ correctlyꢀ knowingꢀ thatꢀ theꢀ
Sim4100:#19eꢀ FYI.ꢀ Panelꢀ Firmwareꢀ firmwareꢀ versionꢀ isꢀ notꢀ supportedꢀ mayꢀ helpꢀ
mayꢀbeꢀincompatible.ꢀ
diagnoseꢀtheꢀproblemꢀmoreꢀeasily.ꢀ
ꢀ
Noꢀ correctiveꢀ actionꢀ isꢀ requiredꢀ onꢀ yourꢀ part.ꢀ Ifꢀ
however,ꢀ someꢀ youꢀ suspectꢀ thatꢀ theꢀ driverꢀ isꢀ notꢀ
operatingꢀcorrectlyꢀitꢀisꢀimportantꢀthatꢀyouꢀmentionꢀ
seeingꢀ thisꢀ messageꢀ inꢀ theꢀ Errorꢀ Bufferꢀ whenꢀ
reportingꢀtheꢀproblem.ꢀ
Sim4100:#20ꢀ FYI.ꢀ Dataꢀ abandoned!ꢀ
Arrayꢀtooꢀshort.ꢀMapDesc=ꢀ<%s>ꢀ
Sim4100:#21.ꢀ Error.ꢀ Dataꢀ abandoned!ꢀ
Arrayꢀtooꢀshortꢀcꢁpꢁs=ꢀ%dꢁ%dꢁ%dꢀ
CheckꢀtheꢀCSVꢀfileꢀDataꢀArrayꢀlengths.ꢀ
CheckꢀtheꢀCSVꢀfileꢀDataꢀArrayꢀlengths.ꢀ
Pollingꢀ isꢀ disabledꢀ untilꢀ theꢀ portꢀ supervisionꢀ
messageꢀhasꢀbeenꢀreceived.ꢀThisꢀmessageꢀcanꢀbeꢀ
safelyꢀ ignored.ꢀ Whenꢀ theꢀ panelꢀ sendsꢀ unsolicitedꢀ
messagesꢀ toꢀ theꢀ FieldServerꢀ thisꢀ messageꢀ isꢀ
printed.ꢀ Pollingꢀ remainsꢀ inhibitedꢀ untilꢀ theꢀ
unsolicitedꢀmessageꢀstreamꢀend.ꢀ
Sim4100:#22.ꢀFYI.ꢀPollingꢀInhibited.ꢀ
Whenꢀaꢀstreamꢀofꢀunsolicitedꢀmessagesꢀisꢀreceivedꢀ
fromꢀtheꢀSimplexꢀpanelꢀthenꢀpollingꢀisꢀinhibitedꢀuntilꢀ
theꢀ streamꢀ ends.ꢀ Whenꢀ theꢀ streamꢀ endsꢀ thisꢀ
messageꢀisꢀprinted.ꢀItꢀmayꢀbeꢀsafelyꢀignored.ꢀ
Sim4100:#23.ꢀFYI.ꢀPollingꢀEnabledꢀ
ꢀ
Sim4100:#25.ꢀ Error.ꢀ Dataꢀ abandoned!ꢀ
Arrayꢀtooꢀshortꢀcꢁpꢁs=ꢀ%dꢁ%dꢁ%dꢀ
Sim4100:#26ꢀ FYI.ꢀ Dataꢀ abandoned!ꢀ
Arrayꢀtooꢀshort.(%d)ꢀMapDesc=<%s>ꢀ
Sim4100:#27.ꢀ FYI.ꢀ Sequenceꢀ Numberꢀ
resetꢀrequestedꢀ&ꢀdone.ꢀ
CheckꢀtheꢀCSVꢀfileꢀDataꢀArrayꢀlengths.ꢀ
CheckꢀtheꢀCSVꢀfileꢀDataꢀArrayꢀlengths.ꢀ
ꢀ
Sim4100:#28.ꢀ
Sim4100_Func=%dꢀinꢀMD=<%s>ꢀ
ꢀ
Error.ꢀ
Badꢀ
Checkꢀ theꢀ CSVꢀ fileꢀ andꢀ driverꢀ manualꢀ forꢀ validꢀ
Simplexꢀfunctions.ꢀ
Sim4100:#29.ꢀFYI.ꢀLengthꢀchangedꢀtoꢀ1ꢀ CheckꢀtheꢀCSVꢀfileꢀforꢀtheꢀcorrectꢀMapꢀDescriptorꢀ
inꢀMapDesc=ꢀ<%s>ꢀ functionꢀtype.ꢀ
Sim4100:#30.ꢀFYI.ꢀLengthꢀchangedꢀtoꢀ1ꢀ CheckꢀtheꢀCSVꢀfileꢀforꢀtheꢀcorrectꢀMapꢀDescriptorꢀ
inꢀMapDesc=ꢀ<%s>ꢀ functionꢀtype.ꢀ
Sim4100:#31.ꢀFYI.ꢀLengthꢀchangedꢀtoꢀ1ꢀ CheckꢀtheꢀCSVꢀfileꢀforꢀtheꢀcorrectꢀMapꢀDescriptorꢀ
inꢀMapDesc=ꢀ<%s>ꢀ
functionꢀtype.ꢀ
Sim4100:#32.ꢀ FYI.ꢀ Sequenceꢀ numberꢀ
semiꢁreset.ꢀ
ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Error Message
Page 47 of 58
Troubleshooting Tip
Messageꢀ sequenceꢀ numbersꢀ incorrect.ꢀ ꢀ Checkꢀ
Sim4100:#33.ꢀ Error.ꢀ Invalidꢀ Seqꢀ Simplexꢀ Userꢀ Manuals,ꢀ andꢀ driverꢀ manuals.ꢀꢀ
Number.ꢀ
Contactꢀ FieldServerꢀ Technologiesꢀ forꢀ additionalꢀ
support.ꢀ
Messageꢀ sequenceꢀ numberꢀ incorrect.ꢀ ꢀ Checkꢀ
Sim4100:#34.ꢀ Badꢀ Seq.ꢀ Sequenceꢀ Simplexꢀ Userꢀ Manuals,ꢀ andꢀ driverꢀ manuals.ꢀ
numberꢀreset.ꢀ
Contactꢀ FieldServerꢀ Technologiesꢀ forꢀ additionalꢀ
support.ꢀ
Sim4100:#36.ꢀ
FYI.ꢀ
Badꢀ CheckꢀtheꢀCSVꢀfileꢀforꢀtheꢀcorrectꢀSimplexꢀfunctionꢀ
sim4100_func=%dꢀinꢀMapDesc=<%s>ꢀ
type.ꢀ
Sim4100:#38.ꢀ FYI.ꢀ Badꢀ CheckꢀtheꢀCSVꢀfileꢀforꢀtheꢀcorrectꢀSimplexꢀfunctionꢀ
sim4100_func=%dꢀinꢀMapDesc=<%s>ꢀ
type.ꢀ
Attributeꢀ wasꢀ found,ꢀ butꢀ Stateꢀ notꢀ foundꢀ inꢀ driverꢀ
table.ꢀ ꢀ Contactꢀ FieldServerꢀ Technologiesꢀ forꢀ
additionalꢀsupport.ꢀ
Sim4100:#39ꢀ FYI.ꢀ Dataꢀ abandoned!ꢀ
Stateꢀnotꢀrecognized.ꢀMapdesc=<%s>ꢀ
Sim4100:#40ꢀ FYI.ꢀ Dataꢀ abandoned!ꢀ
Arrayꢀtooꢀshort.(%d)ꢀMapdesc=<%s>ꢀ
Sim4100:#41ꢀ FYI.ꢀ Dataꢀ abandoned!ꢀ
Arrayꢀtooꢀshort.(%d)ꢀMapdesc=<%s>ꢀ
CheckꢀtheꢀCSVꢀfileꢀDataꢀArrayꢀlengthsꢀ
CheckꢀtheꢀCSVꢀfileꢀDataꢀArrayꢀlengthsꢀ
Sim4100:#43.ꢀErr.ꢀCanꢀonlyꢀmonitorꢀ%dꢀ Contactꢀ FieldServerꢀ Technologiesꢀ forꢀ additionalꢀ
point(s)ꢀforꢀClearAllꢀ support.ꢀ
Sim4100:#44ꢀ FYI.ꢀ ClearAllꢀ mapDesc'sꢀ Mapꢀ Descriptorꢀ functionꢀ hasꢀ beenꢀ changedꢀ
mustꢀbeꢀpassiveꢀ
automaticallyꢀ
Sim4100:#45ꢀ FYI.ꢀ Userꢀ addedꢀ SHOWꢀ
attribute=<%s>ꢀoffset=%dꢀmethod=%dꢀ
ꢀ
Sim4100:#46ꢀ Err.ꢀ Noꢀ space.ꢀ Driverꢀ Noꢀ spaceꢀ isꢀ availableꢀ inꢀ internalꢀ driverꢀ table.ꢀꢀ
rejectsꢀ
offset=%dꢀmethod=%dꢀ
SHOWꢀ
attribute=<%s>ꢀ Contactꢀ FieldServerꢀ Technologiesꢀ forꢀ additionalꢀ
support.ꢀ
Sim4100:#47ꢀ Err.ꢀ Duplicate.ꢀ Driverꢀ
Duplicateꢀ foundꢀ inꢀ internalꢀ driverꢀ table.ꢀ ꢀ Contactꢀ
FieldServerꢀTechnologiesꢀforꢀadditionalꢀsupport.ꢀ
rejectsꢀ
SHOWꢀ
attribute=<%s>ꢀ
offset=%dꢀmethod=%dꢀ
Sim4100:#48ꢀ FYI.ꢀ Userꢀ addedꢀ SHOWꢀ
attrꢀstate=<%s>ꢀvalue=%dꢀ
ꢀ
Sim4100:#49ꢀ Err.ꢀ Noꢀ space.ꢀ Driverꢀ Noꢀ spaceꢀ isꢀ availableꢀ inꢀ internalꢀ driverꢀ table.ꢀꢀ
rejectsꢀ SHOWꢀ attrꢀ state=<%s>ꢀ Contactꢀ FieldServerꢀ Technologiesꢀ forꢀ additionalꢀ
value=%dꢀ
support.ꢀ
Sim4100:#50ꢀ Err.ꢀ Duplicate.ꢀ Driverꢀ
rejectsꢀ SHOWꢀ attrꢀ state=<%s>ꢀ
value=%dꢀ
Duplicateꢀ foundꢀ inꢀ internalꢀ driverꢀ table.ꢀ ꢀ Contactꢀ
FieldServerꢀTechnologiesꢀforꢀadditionalꢀsupport.ꢀ
sim4100:#51ꢀ Err.ꢀ Lengthꢀ mustꢀ beꢀ
specifiedꢀandꢀ>ꢀ0.ꢀ
CheckꢀtheꢀCSVꢀfileꢀforꢀtheꢀlengthꢀfields.ꢀ
Checkꢀ theꢀ CSVꢀ fileꢀ forꢀ nodeꢀ definitions,ꢀ Simplexꢀ
SIM4100:#52ꢀ
Abandoned.ꢀNodeꢀofflineꢀ
FYI.ꢀ
Incomingꢀ hardware,ꢀ andꢀ connections.ꢀ ꢀ Aꢀ deviceꢀ nodeꢀ
appearsꢀ toꢀ beꢀ offline.ꢀ ꢀ Contactꢀ FieldServerꢀ
Technologiesꢀforꢀadditionalꢀsupport.ꢀ
Sim4100:#53.ꢀ Md=<%s>ꢀ Abandoned.ꢀ Obsolete.ꢀ ꢀ Contactꢀ FieldServerꢀ Technologiesꢀ forꢀ
Pollingꢀwasꢀinhibited.ꢀ support.ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Error Message
Page 48 of 58
Troubleshooting Tip
Sequenceꢀnumberꢀcheckingꢀwasꢀdisabled.ꢀꢀCheckꢀ
yourꢀpassword.ꢀꢀContactꢀFieldServerꢀTechnologiesꢀ
forꢀsupport.ꢀ
Sim4100:#54.ꢀ Err.ꢀ SeqNumberꢀ checkꢀ
disabled.ꢀ
Sim4100:#55.ꢀ
Error.ꢀ
Badꢀ CheckꢀtheꢀCSVꢀfileꢀforꢀtheꢀcorrectꢀSimplexꢀfunctionꢀ
Sim4100_Func=%dꢀinꢀMD=<%s>ꢀ
type.ꢀ
Sim4100:#56ꢀ
Notꢀused.ꢀ
TheꢀdriverꢀignoredꢀLoginꢀmessages.ꢀNoꢀcorrectiveꢀ
actionꢀisꢀrequired.ꢀThisꢀmessageꢀisꢀprintedꢀforꢀyourꢀ
informationꢀonly.ꢀ
Sim4100:#57*ꢀ Err.ꢀ Cantꢀ parseꢀ Loginꢀ
message.ꢀIgnored.ꢀ
Sim4100:#58ꢀFYI.ꢀYouꢀcouldꢀhaveꢀusedꢀ Thisꢀmessageꢀisꢀprintedꢀforꢀyourꢀinformationꢀonly.ꢀItꢀ
anꢀ Arrayꢀ calledꢀ <%s>ꢀ toꢀ exposeꢀ canꢀ safelyꢀ beꢀ ignored.ꢀ Forꢀ additionalꢀ informationꢀ
diagnosticꢀinfo.ꢀ
readꢀsectionꢀ“AppendixꢀA.7.2ꢀDriverꢀExposedꢀStats”ꢀ
Anꢀ internalꢀ driverꢀ diagnosticꢀ hasꢀ beenꢀ triggered.ꢀ
Youꢀ mustꢀ reportꢀ thisꢀ errorꢀ toꢀ FieldServer’sꢀ
TechnicalꢀSupport.ꢀ
Sim4100:#59ꢀ Err.ꢀ Checkpoint.ꢀ Reportꢀ
thisꢀtoꢀTechꢀSupport.ꢀ
EveryꢀSim4100ꢀMapꢀDescriptorꢀmustꢀbeꢀconnectedꢀ
toꢀaꢀnode.ꢀEnsureꢀthatꢀtheꢀparameterꢀ‘Node_Name’ꢀ
hasꢀbeenꢀspecifiedꢀonꢀtheꢀMapꢀDescriptor.ꢀ
ꢀ
Toꢀ correctꢀ thisꢀ problem,ꢀ editꢀ theꢀ CSV,ꢀ makeꢀ theꢀ
correction,ꢀ downloadꢀ theꢀ correctedꢀ CSVꢀ fileꢀ andꢀ
resetꢀtheꢀFieldServer.ꢀ
Sim4100:#60ꢀ Err.ꢀ MapDesc=%s.ꢀ Noꢀ
Node.ꢀ
IfꢀyouꢀhaveꢀaꢀMapꢀDescritorꢀwhichꢀhasꢀtheꢀ
sim4100_funcꢀparameterꢀsetꢀtoꢀ‘earths’ꢀorꢀtoꢀ
‘values’ꢀthenꢀyouꢀmustꢀsetꢀtheꢀPLC_Typeꢀ
parameterꢀonꢀtheꢀnodeꢀtoꢀ4100U.ꢀ(Seeꢀsectionꢀ0ꢀꢀ
Clientꢀ Sideꢀ Nodeꢀ Descriptorsꢀ ).ꢀ Itꢀ isꢀ onlyꢀ
appropriateꢀtoꢀdoꢀsoꢀifꢀtheꢀfirmwareꢀversionꢀofꢀyourꢀ
Sim4100:#61ꢀ Err.ꢀ PLC_Type=4100uꢀ panelꢀ isꢀ 10.xꢀ orꢀ later.ꢀ Youꢀ canꢀ createꢀ aꢀ mapꢀ
rqdꢀforꢀ'values'/'earths'ꢀ
descriptorꢀtoꢀreadꢀtheꢀversionꢀinformationꢀifꢀyouꢀareꢀ
notꢀsure.ꢀYouꢀcanꢀalsoꢀuseꢀtheꢀmenuꢀsystemꢀonꢀtheꢀ
Panelꢀtoꢀreadꢀtheꢀversionꢀnumber.ꢀ
ꢀ
Toꢀ correctꢀ thisꢀ problem,ꢀ editꢀ theꢀ CSV,ꢀ makeꢀ theꢀ
correction,ꢀ downloadꢀ theꢀ correctedꢀ CSVꢀ fileꢀ andꢀ
resetꢀtheꢀFieldServer.ꢀ
Thisꢀ messageꢀ isꢀ printedꢀ whenꢀ theꢀ inputꢀ bufferꢀ
overflows.ꢀ Thisꢀ usuallyꢀ occursꢀ whenꢀ theꢀ panelꢀ
sendsꢀ lotsꢀ ofꢀ messagesꢀ andꢀ theyꢀ areꢀ notꢀ beingꢀ
processedꢀ byꢀ theꢀ driverꢀ fastꢀ enough.ꢀ ꢀ Aꢀ panicꢀ isꢀ
printedꢀimmediateꢀafterꢀthisꢀmessage.ꢀ
ꢀ
Sim4100:#62ꢀErr.ꢀInputꢀBufferꢀOverflow.ꢀ Theꢀ driverꢀ willꢀ clearꢀ theꢀ bufferꢀ andꢀ startꢀ capturingꢀ
newꢀ bytesꢀ asꢀ theyꢀ arrive.ꢀ Messagesꢀ mayꢀ haveꢀ
beenꢀlost.ꢀWeꢀadviseꢀthatꢀyouꢀreꢁsynchꢀtheꢀpanel.ꢀ
ꢀ
Thisꢀ errorꢀ hasꢀ onlyꢀ beenꢀ seenꢀ once.ꢀ Itꢀ occurredꢀ
whenꢀaꢀpanelꢀwasꢀconnectedꢀtoꢀtheꢀdriverꢀwithꢀtheꢀ
wrongꢀconnectionꢀsettings.ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Appendix D. Pseudo Points
Page 49 of 58
Itꢀ isꢀ beyondꢀ theꢀ scopeꢀ ofꢀ theꢀ driverꢀ manualꢀ toꢀ describeꢀ theꢀ fullꢀ functionalityꢀ ofꢀ theꢀ Simplexꢀ
Panels.ꢀ However,ꢀ weꢀ haveꢀ foundꢀ itꢀ usefulꢀ toꢀ provideꢀ theꢀ followingꢀ dataꢀ toꢀ customers.ꢀ Theꢀ
followingꢀinformationꢀisꢀnotꢀmaintainedꢀandꢀupdatedꢀthereforeꢀyouꢀshouldꢀuseꢀitꢀforꢀreferenceꢀ
onlyꢀandꢀshouldꢀalwaysꢀconsultꢀwithꢀtheꢀvendorꢀofꢀyourꢀSimplexꢀsystemꢀbeforeꢀimplementingꢀ
anyꢀprojectꢀdecisionsꢀorꢀactionsꢀbasedꢀonꢀtheꢀinformationꢀprovidedꢀinꢀthisꢀsection.ꢀ
ꢀ
PseudoꢀpointsꢀareꢀpointsꢀthatꢀreportꢀstatesꢀorꢀattributesꢀbasedꢀonꢀhowꢀtheꢀSimplexꢀsystemꢀhasꢀ
beenꢀinstalled,ꢀconfiguredꢀandꢀprogrammed.ꢀꢀTheyꢀareꢀoftenꢀprogrammedꢀtoꢀgroups,ꢀdevices,ꢀ
zonesꢀorꢀotherꢀlogicꢀgroupings.ꢀꢀForꢀexample,ꢀaꢀpseudoꢀpointꢀmayꢀbeꢀprogrammedꢀtoꢀreportꢀifꢀ
andꢀonlyꢀifꢀmoreꢀthanꢀoneꢀsensorꢀinꢀaꢀparticularꢀareaꢀisꢀreportingꢀsmoke.ꢀ
ꢀ
EveryꢀSimplexꢀsystemꢀhasꢀaꢀnumberꢀofꢀdefaultꢀpseudoꢀpointsꢀprogrammedꢀintoꢀtheꢀfirmwareꢀ
suppliedꢀwithꢀtheꢀpanel.ꢀTheseꢀdefaultꢀpointsꢀdependꢀonlyꢀonꢀtheꢀfirmwareꢀrevisionꢀnumberꢀandꢀ
areꢀgenerallyꢀunaffectedꢀbyꢀtheꢀconfigurationꢀprogrammedꢀforꢀaꢀparticularꢀsite.ꢀ
ꢀ
Althoughꢀtheꢀ4100ꢀcardꢀnumberꢀcanꢀrangeꢀfromꢀ0ꢁ250ꢀinꢀtheory,ꢀonlyꢀtheꢀfollowingꢀrangesꢀareꢀ
presentlyꢀusedꢀinꢀtheꢀsystem:ꢀ
ꢀ
Cardꢀaddressꢀ
0ꢁ119ꢀ
128ꢁ143ꢀ
144ꢁ159ꢀ
160ꢁ175ꢀ
Cardꢀtypeꢀ
Physicalꢀ(Hardware)ꢀcardsꢀ
DigitalꢀPseudoꢀcardsꢀ
AnalogꢀPseudoꢀcardsꢀ
ListꢀPseudoꢀcardsꢀ
ꢀ
Digitalꢀ Pseudo’s:ꢀ Thereꢀ areꢀ 250ꢀ fixedꢀ pseudo'sꢀ inꢀ theꢀ 4020ꢀ panelꢀ andꢀ 511ꢀ inꢀ theꢀ 4100ꢀ andꢀ
4100U.ꢀꢀTheꢀnumberingꢀsequenceꢀisꢀsimple,ꢀ128ꢀstartsꢀtheꢀfirstꢀblockꢀofꢀ256ꢀ(0ꢀtoꢀ255),ꢀsoꢀtheꢀ
firstꢀpointꢀisꢀ128ꢁ0ꢁ0,ꢀtheꢀsecondꢀisꢀ128ꢁ1ꢁ0,ꢀandꢀsoꢀon.ꢀꢀTheꢀnextꢀblockꢀstartsꢀatꢀ129ꢀandꢀfollowsꢀ
theꢀsameꢀsequence,ꢀthenꢀ130ꢀandꢀsoꢀonꢀupꢀtoꢀ143.ꢀꢀInꢀtheꢀ4100ꢀtheꢀfirstꢀuserꢀdefinableꢀpseudoꢀ
isꢀPꢁ256,ꢀinꢀtheꢀ4100Uꢀit'sꢀPꢁ512.ꢀ
ꢀ
P0ꢀ SYSTEMꢀRESETꢀKEYꢀ
P1ꢀ ALARMꢀSILENCEꢀKEYꢀ
UTILITYꢀ 128ꢁ0ꢁ0ꢀ
UTILITYꢀ 128ꢁ1ꢁ0ꢀ
P2ꢀ FRONTꢀPANELꢀLAMPTESTꢀCONTROLꢀ(ANNUNC.ꢀ0)ꢀ UTILITYꢀ 128ꢁ2ꢁ0ꢀ
P3ꢀ FIREꢀALARMꢀDETECTꢀ
UTILITYꢀ 128ꢁ3ꢁ0ꢀ
UTILITYꢀ 128ꢁ4ꢁ0ꢀ
UTILITYꢀ 128ꢁ5ꢁ0ꢀ
UTILITYꢀ 128ꢁ6ꢁ0ꢀ
TROUBLEꢀ128ꢁ7ꢁ0ꢀ
UTILITYꢀ 128ꢁ8ꢁ0ꢀ
TROUBLEꢀ128ꢁ9ꢁ0ꢀ
UTILITYꢀ 128ꢁ10ꢁ0ꢀ
UTILITYꢀ 128ꢁ11ꢁ0ꢀ
UTILITYꢀ 128ꢁ12ꢁ0ꢀ
UTILITYꢀ 128ꢁ13ꢁ0ꢀ
P4ꢀ GLOBALꢀACKNOWLEDGEꢀENABLEꢀ
P5ꢀ SETꢀSERVICEꢀPSEUDOꢀVALUESꢀ
P6ꢀ ALARMꢀSILENCEꢀ
P7ꢀ EXTRAꢀCARDꢀINꢀTHEꢀSYSTEMꢀ
P8ꢀ KEYPADꢀACTIVEꢀ
P9ꢀ SYSTEMꢀOUTꢀOFꢀCQB'Sꢀ
P10ꢀ CODEDꢀINPUTꢀACTIVEꢀ
P11ꢀ UNACKNOWLEDGEDꢀFIREꢀALARMꢀEXISTSꢀ
P12ꢀ UNACKNOWLEDGEDꢀSUPERVISORYꢀEXISTSꢀ
P13ꢀ UNACKNOWLEDGEDꢀTROUBLEꢀEXISTSꢀ
P14ꢀ SYSTEMꢀDISABLEDꢀꢁꢀPROGRAMMERꢀDOWNLOADꢀ TROUBLEꢀ128ꢁ14ꢁ0ꢀ
P15ꢀ CFIGꢀRAMꢀWRITEꢀPROTECTꢀMISSINGꢀ(SW1ꢁ1)ꢀ
P16ꢀ SMPLꢀPROGRAMꢀ0ꢀꢁꢀSYSTEMꢀDEFAULTꢀ
TROUBLEꢀ128ꢁ15ꢁ0ꢀ
UTILITYꢀ 128ꢁ16ꢁ0ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 50 of 58
P17ꢀ SMPLꢀPROGRAMꢀ1ꢀꢁꢀDEFAULTꢀAUDIOꢀ
UTILITYꢀ 128ꢁ17ꢁ0ꢀ
P18ꢀ SMPLꢀPROGRAMꢀ2ꢀꢁꢀSYSTEMꢀOPTIONSꢀ(CODING)ꢀ UTILITYꢀ 128ꢁ18ꢁ0ꢀ
P19ꢀ SMPLꢀPROGRAMꢀ3ꢀꢁꢀUSERꢀCUSTOMꢀCONTROLꢀ
P20ꢀ SMPLꢀPROGRAMꢀ4ꢀꢁꢀUSERꢀCUSTOMꢀCONTROLꢀ
P21ꢀ SMPLꢀPROGRAMꢀ5ꢀꢁꢀUSERꢀCUSTOMꢀCONTROLꢀ
P22ꢀ SMPLꢀPROGRAMꢀ6ꢀꢁꢀUSERꢀCUSTOMꢀCONTROLꢀ
P23ꢀ SMPLꢀPROGRAMꢀ7ꢀꢁꢀUSERꢀCUSTOMꢀCONTROLꢀ
P24ꢀ CODINGꢀGROUPꢀ0ꢀACTIVEꢀ
P25ꢀ CODINGꢀGROUPꢀ1ꢀACTIVEꢀ
P26ꢀ CODINGꢀGROUPꢀ2ꢀACTIVEꢀ
P27ꢀ CODINGꢀGROUPꢀ3ꢀACTIVEꢀ
P28ꢀ CODINGꢀGROUPꢀ4ꢀACTIVEꢀ
P29ꢀ CODINGꢀGROUPꢀ5ꢀACTIVEꢀ
P30ꢀ CODINGꢀGROUPꢀ6ꢀACTIVEꢀ
P31ꢀ CODINGꢀGROUPꢀ7ꢀACTIVEꢀ
P32ꢀ COLDꢀSTARTꢀ
P33ꢀ WARMꢀSTARTꢀ
P34ꢀ CITYꢀDISCONNECTꢀ
P35ꢀ MANUALꢀEVACUATIONꢀSWITCHꢀINPUTꢀ
P36ꢀ ELEVATORꢀBYPASSꢀ
P37ꢀ DOORHOLDERꢀBYPASSꢀ
UTILITYꢀ 128ꢁ19ꢁ0ꢀ
UTILITYꢀ 128ꢁ20ꢁ0ꢀ
UTILITYꢀ 128ꢁ21ꢁ0ꢀ
UTILITYꢀ 128ꢁ22ꢁ0ꢀ
UTILITYꢀ 128ꢁ23ꢁ0ꢀ
UTILITYꢀ 128ꢁ24ꢁ0ꢀ
UTILITYꢀ 128ꢁ25ꢁ0ꢀ
UTILITYꢀ 128ꢁ26ꢁ0ꢀ
UTILITYꢀ 128ꢁ27ꢁ0ꢀ
UTILITYꢀ 128ꢁ28ꢁ0ꢀ
UTILITYꢀ 128ꢁ29ꢁ0ꢀ
UTILITYꢀ 128ꢁ30ꢁ0ꢀ
UTILITYꢀ 128ꢁ31ꢁ0ꢀ
TROUBLEꢀ128ꢁ32ꢁ0ꢀ
TROUBLEꢀ128ꢁ33ꢁ0ꢀ
TROUBLEꢀ128ꢁ34ꢁ0ꢀ
UTILITYꢀ 128ꢁ35ꢁ0ꢀ
TROUBLEꢀ128ꢁ36ꢁ0ꢀ
TROUBLEꢀ128ꢁ37ꢁ0ꢀ
TROUBLEꢀ128ꢁ38ꢁ0ꢀ
TROUBLEꢀ128ꢁ39ꢁ0ꢀ
UTILITYꢀ 128ꢁ40ꢁ0ꢀ
UTILITYꢀ 128ꢁ41ꢁ0ꢀ
UTILITYꢀ 128ꢁ42ꢁ0ꢀ
UTILITYꢀ 128ꢁ43ꢁ0ꢀ
UTILITYꢀ 128ꢁ44ꢁ0ꢀ
UTILITYꢀ 128ꢁ45ꢁ0ꢀ
UTILITYꢀ 128ꢁ46ꢁ0ꢀ
UTILITYꢀ 128ꢁ47ꢁ0ꢀ
P38ꢀ CONTROLꢀPOINTꢀBYPASSꢀ
P39ꢀ SYSTEMꢀEXECUTINGꢀFROMꢀRAMꢀ
P40ꢀ AUTOMATICꢀDETECTORꢀRESETꢀ
P41ꢀ MASTERꢀFIREꢀALARMꢀACKꢀKEYꢀ
P42ꢀ MASTERꢀSUPERVISORYꢀACKꢀKEYꢀ
P43ꢀ MASTERꢀTROUBLEꢀACKꢀKEYꢀ
P44ꢀ CODINGꢀBUSꢀDISABLEꢀSWITCHꢀ
P45ꢀ DRILLꢀSWITCHꢀINPUTꢀ
P46ꢀ DOORꢀHOLDERꢀTRIGGERꢀ
P47ꢀ SIGNALS/VISUALSꢀACTIVEꢀ
P48ꢀ MANUALꢀEVACUATIONꢀ
FIREꢀ
128ꢁ48ꢁ0ꢀ
P49ꢀ SYSTEMꢀATꢀACCESSꢀLEVELꢀ1ꢀORꢀGREATERꢀ
P50ꢀ SYSTEMꢀATꢀACCESSꢀLEVELꢀ2ꢀORꢀGREATERꢀ
P51ꢀ SYSTEMꢀATꢀACCESSꢀLEVELꢀ3ꢀORꢀGREATERꢀ
P52ꢀ SYSTEMꢀATꢀACCESSꢀLEVELꢀ4ꢀ
UTILITYꢀ 128ꢁ49ꢁ0ꢀ
UTILITYꢀ 128ꢁ50ꢁ0ꢀ
UTILITYꢀ 128ꢁ51ꢁ0ꢀ
UTILITYꢀ 128ꢁ52ꢁ0ꢀ
P53ꢀ SYSTEMꢀLISTꢀOVERFLOWꢀꢁꢀWARMꢀSTARTꢀNEEDEDꢀ TROUBLEꢀ128ꢁ53ꢁ0ꢀ
P54ꢀ NETWORKꢀMIKEꢀKEYEDꢀ
P55ꢀ CRTꢀKEYPADꢀINACTIVITYꢀTIMERꢀDISABLEꢀ
UTILITYꢀ 128ꢁ54ꢁ0ꢀ
UTILITYꢀ 128ꢁ55ꢁ0ꢀ
P56ꢀ CITYꢀCIRCUITꢀSTDꢀTROUBLEꢀRELAYꢀOPERATIONꢀ UTILITYꢀ 128ꢁ56ꢁ0ꢀ
P57ꢀ KEYPADꢀINACTIVITYꢀTIMERꢀDISABLEꢀ
P58ꢀ SYSTEMꢀTIME/DATEꢀINVALIDꢀORꢀNOTꢀSETꢀ
P59ꢀ ALARMꢀVERIFICATIONꢀTALLYꢀLIMITꢀEXCEEDEDꢀ
P60ꢀ ALARMꢀVERIFICATIONꢀGROUPꢀ0ꢀACTIVEꢀ
P61ꢀ ALARMꢀVERIFICATIONꢀGROUPꢀ1ꢀACTIVEꢀ
P62ꢀ ALARMꢀVERIFICATIONꢀGROUPꢀ2ꢀACTIVEꢀ
P63ꢀ ALARMꢀVERIFICATIONꢀGROUPꢀ3ꢀACTIVEꢀ
UTILITYꢀ 128ꢁ57ꢁ0ꢀ
TROUBLEꢀ128ꢁ58ꢁ0ꢀ
TROUBLEꢀ128ꢁ59ꢁ0ꢀ
UTILITYꢀ 128ꢁ60ꢁ0ꢀ
UTILITYꢀ 128ꢁ61ꢁ0ꢀ
UTILITYꢀ 128ꢁ62ꢁ0ꢀ
UTILITYꢀ 128ꢁ63ꢁ0ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 51 of 58
P64ꢀ ALARMꢀVERIFICATIONꢀGROUPꢀ4ꢀACTIVEꢀ
P65ꢀ ALARMꢀVERIFICATIONꢀGROUPꢀ5ꢀACTIVEꢀ
P66ꢀ ALARMꢀVERIFICATIONꢀGROUPꢀ6ꢀACTIVEꢀ
P67ꢀ ALARMꢀVERIFICATIONꢀGROUPꢀ7ꢀACTIVEꢀ
P68ꢀ FIRSTꢀSTAGEꢀTIMERꢀEXPIREDꢀ
P69ꢀ THEꢀEVACꢀMESSAGEꢀHASꢀPLAYEDꢀ
P70ꢀ WALKꢀTESTꢀGROUPꢀ0ꢀENABLEDꢀ
P71ꢀ WALKꢀTESTꢀGROUPꢀ1ꢀENABLEDꢀ
P72ꢀ WALKꢀTESTꢀGROUPꢀ2ꢀENABLEDꢀ
P73ꢀ WALKꢀTESTꢀGROUPꢀ3ꢀENABLEDꢀ
P74ꢀ WALKꢀTESTꢀGROUPꢀ4ꢀENABLEDꢀ
P75ꢀ WALKꢀTESTꢀGROUPꢀ5ꢀENABLEDꢀ
P76ꢀ WALKꢀTESTꢀGROUPꢀ6ꢀENABLEDꢀ
P77ꢀ WALKꢀTESTꢀGROUPꢀ7ꢀENABLEDꢀ
P78ꢀ ALARMꢀSILENCE/ALARMꢀCUTOUTꢀPSEUDOꢀ
UTILITYꢀ 128ꢁ64ꢁ0ꢀ
UTILITYꢀ 128ꢁ65ꢁ0ꢀ
UTILITYꢀ 128ꢁ66ꢁ0ꢀ
UTILITYꢀ 128ꢁ67ꢁ0ꢀ
UTILITYꢀ 128ꢁ68ꢁ0ꢀ
UTILITYꢀ 128ꢁ69ꢁ0ꢀ
TROUBLEꢀ128ꢁ70ꢁ0ꢀ
TROUBLEꢀ128ꢁ71ꢁ0ꢀ
TROUBLEꢀ128ꢁ72ꢁ0ꢀ
TROUBLEꢀ128ꢁ73ꢁ0ꢀ
TROUBLEꢀ128ꢁ74ꢁ0ꢀ
TROUBLEꢀ128ꢁ75ꢁ0ꢀ
TROUBLEꢀ128ꢁ76ꢁ0ꢀ
TROUBLEꢀ128ꢁ77ꢁ0ꢀ
UTILITYꢀ 128ꢁ78ꢁ0ꢀ
P79ꢀ RESETꢀSPKRSꢀWHENꢀAUDIOꢀCODINGꢀCOMPLETEꢀ UTILITYꢀ 128ꢁ79ꢁ0ꢀ
P80ꢀ MASTERꢀMICROPHONEꢀKEYEDꢀ
P81ꢀ REMOTEꢀMICROPHONEꢀ1ꢀKEYEDꢀ
P82ꢀ REMOTEꢀMICROPHONEꢀ2ꢀKEYEDꢀ
P83ꢀ REMOTEꢀMICROPHONEꢀ1ꢀREADYꢀTOꢀTALKꢀ
P84ꢀ REMOTEꢀMICROPHONEꢀ2ꢀREADYꢀTOꢀTALKꢀ
P85ꢀ VTGꢀ1ꢀꢁꢀACTIVEꢀ
UTILITYꢀ 128ꢁ80ꢁ0ꢀ
UTILITYꢀ 128ꢁ81ꢁ0ꢀ
UTILITYꢀ 128ꢁ82ꢁ0ꢀ
UTILITYꢀ 128ꢁ83ꢁ0ꢀ
UTILITYꢀ 128ꢁ84ꢁ0ꢀ
UTILITYꢀ 128ꢁ85ꢁ0ꢀ
UTILITYꢀ 128ꢁ86ꢁ0ꢀ
UTILITYꢀ 128ꢁ87ꢁ0ꢀ
UTILITYꢀ 128ꢁ88ꢁ0ꢀ
UTILITYꢀ 128ꢁ89ꢁ0ꢀ
UTILITYꢀ 128ꢁ90ꢁ0ꢀ
UTILITYꢀ 128ꢁ91ꢁ0ꢀ
UTILITYꢀ 128ꢁ92ꢁ0ꢀ
UTILITYꢀ 128ꢁ93ꢁ0ꢀ
UTILITYꢀ 128ꢁ94ꢁ0ꢀ
UTILITYꢀ 128ꢁ95ꢁ0ꢀ
UTILITYꢀ 128ꢁ96ꢁ0ꢀ
UTILITYꢀ 128ꢁ97ꢁ0ꢀ
UTILITYꢀ 128ꢁ98ꢁ0ꢀ
UTILITYꢀ 128ꢁ99ꢁ0ꢀ
UTILITYꢀ 128ꢁ100ꢁ0ꢀ
UTILITYꢀ 128ꢁ101ꢁ0ꢀ
UTILITYꢀ 128ꢁ102ꢁ0ꢀ
UTILITYꢀ 128ꢁ103ꢁ0ꢀ
UTILITYꢀ 128ꢁ104ꢁ0ꢀ
UTILITYꢀ 128ꢁ105ꢁ0ꢀ
UTILITYꢀ 128ꢁ106ꢁ0ꢀ
UTILITYꢀ 128ꢁ107ꢁ0ꢀ
UTILITYꢀ 128ꢁ108ꢁ0ꢀ
UTILITYꢀ 128ꢁ109ꢁ0ꢀ
TROUBLEꢀ128ꢁ110ꢁ0ꢀ
P86ꢀ VTGꢀ2ꢀꢁꢀACTIVEꢀ
P87ꢀ EVACUATIONꢀMESSAGEꢀONꢀ
P88ꢀ EVACUATIONꢀMESSAGEꢀOFFꢀ
P89ꢀ EVACUATIONꢀMESSAGEꢀLEDꢀ
P90ꢀ ALERTꢀMESSAGEꢀONꢀ
P91ꢀ ALERTꢀMESSAGEꢀOFFꢀ
P92ꢀ ALERTꢀMESSAGEꢀLEDꢀ
P93ꢀ DRILLꢀMESSAGEꢀONꢀ
P94ꢀ DRILLꢀMESSAGEꢀOFFꢀ
P95ꢀ DRILLꢀMESSAGEꢀLEDꢀ
P96ꢀ ALLꢀCLEARꢀMESSAGEꢀONꢀ
P97ꢀ ALLꢀCLEARꢀMESSAGEꢀOFFꢀ
P98ꢀ ALLꢀCLEARꢀMESSAGEꢀLEDꢀ
P99ꢀ AUXꢀMSGꢀ1ꢀONꢀ
P100ꢀAUXꢀMSGꢀ1ꢀOFFꢀ
P101ꢀAUXꢀMSGꢀ1ꢀLEDꢀ
P102ꢀAUXꢀMSGꢀ2ꢀONꢀ
P103ꢀAUXꢀMSGꢀ2ꢀOFFꢀ
P104ꢀAUXꢀMSGꢀ2ꢀLEDꢀ
P105ꢀPHONEꢀPAGINGꢀONꢀ
P106ꢀPHONEꢀPAGINGꢀOFFꢀ
P107ꢀPHONEꢀPAGINGꢀLEDꢀ
P108ꢀAUDIOꢀOVERRIDEꢀONꢀ
P109ꢀAUDIOꢀOVERRIDEꢀOFFꢀ
P110ꢀAUDIOꢀOVERRIDEꢀTROUBLEꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 52 of 58
P111ꢀALLꢀSPEAKERSꢀMINUSꢀONꢀ
UTILITYꢀ 128ꢁ111ꢁ0ꢀ
P112ꢀALLꢀSPEAKERSꢀMINUSꢀOFFꢀ
P113ꢀALLꢀSPEAKERSꢀMINUSꢀLEDꢀ
UTILITYꢀ 128ꢁ112ꢁ0ꢀ
UTILITYꢀ 128ꢁ113ꢁ0ꢀ
UTILITYꢀ 128ꢁ114ꢁ0ꢀ
UTILITYꢀ 128ꢁ115ꢁ0ꢀ
UTILITYꢀ 128ꢁ116ꢁ0ꢀ
UTILITYꢀ 128ꢁ117ꢁ0ꢀ
UTILITYꢀ 128ꢁ118ꢁ0ꢀ
UTILITYꢀ 128ꢁ119ꢁ0ꢀ
UTILITYꢀ 128ꢁ120ꢁ0ꢀ
UTILITYꢀ 128ꢁ121ꢁ0ꢀ
UTILITYꢀ 128ꢁ122ꢁ0ꢀ
UTILITYꢀ 128ꢁ123ꢁ0ꢀ
UTILITYꢀ 128ꢁ124ꢁ0ꢀ
UTILITYꢀ 128ꢁ125ꢁ0ꢀ
UTILITYꢀ 128ꢁ126ꢁ0ꢀ
UTILITYꢀ 128ꢁ127ꢁ0ꢀ
UTILITYꢀ 128ꢁ128ꢁ0ꢀ
UTILITYꢀ 128ꢁ129ꢁ0ꢀ
UTILITYꢀ 128ꢁ130ꢁ0ꢀ
UTILITYꢀ 128ꢁ131ꢁ0ꢀ
TROUBLEꢀ128ꢁ132ꢁ0ꢀ
UTILITYꢀ 128ꢁ133ꢁ0ꢀ
TROUBLEꢀ128ꢁ134ꢁ0ꢀ
UTILITYꢀ 128ꢁ135ꢁ0ꢀ
UTILITYꢀ 128ꢁ136ꢁ0ꢀ
UTILITYꢀ 128ꢁ137ꢁ0ꢀ
UTILITYꢀ 128ꢁ138ꢁ0ꢀ
UTILITYꢀ 128ꢁ139ꢁ0ꢀ
UTILITYꢀ 128ꢁ140ꢁ0ꢀ
UTILITYꢀ 128ꢁ141ꢁ0ꢀ
UTILITYꢀ 128ꢁ142ꢁ0ꢀ
UTILITYꢀ 128ꢁ143ꢁ0ꢀ
UTILITYꢀ 128ꢁ144ꢁ0ꢀ
UTILITYꢀ 128ꢁ145ꢁ0ꢀ
UTILITYꢀ 128ꢁ146ꢁ0ꢀ
P114ꢀALLꢀSPEAKERSꢀCHANNELꢀ1ꢀONꢀ
P115ꢀALLꢀSPEAKERSꢀCHANNELꢀ1ꢀOFFꢀ
P116ꢀALLꢀSPEAKERSꢀCHANNELꢀ1ꢀLEDꢀ
P117ꢀALLꢀSPEAKERSꢀCHANNELꢀ2ꢀONꢀ
P118ꢀALLꢀSPEAKERSꢀCHANNELꢀ2ꢀOFFꢀ
P119ꢀALLꢀSPEAKERSꢀCHANNELꢀ2ꢀLEDꢀ
P120ꢀALLꢀSPEAKERSꢀCHANNELꢀ3ꢀONꢀ
P121ꢀALLꢀSPEAKERSꢀCHANNELꢀ3ꢀOFFꢀ
P122ꢀALLꢀSPEAKERSꢀCHANNELꢀ3ꢀLEDꢀ
P123ꢀLOCALꢀSPEAKERꢀEVACꢀONꢀ
P124ꢀLOCALꢀSPEAKERꢀEVACꢀOFFꢀ
P125ꢀLOCALꢀSPEAKERꢀEVACꢀLEDꢀ
P126ꢀLOCALꢀSPEAKERꢀALERTꢀONꢀ
P127ꢀLOCALꢀSPEAKERꢀALERTꢀOFFꢀ
P128ꢀLOCALꢀSPEAKERꢀALERTꢀLEDꢀ
P129ꢀALLꢀSPEAKERSꢀTALKꢀONꢀ
P130ꢀALLꢀSPEAKERSꢀTALKꢀOFFꢀ
P131ꢀALLꢀSPEAKERSꢀTALKꢀLEDꢀ
P132ꢀANALOGꢀSENSORꢀALMOSTꢀDIRTYꢀLOGꢀENABLEꢀ
P133ꢀLOGꢀANALOGꢀSENSORꢀPEAKꢀVALUEꢀENABLEꢀ
P134ꢀCLEARꢀANALOGꢀSENSORꢀPEAKꢀVALUEꢀ
P135ꢀALLꢀALERTꢀ
P136ꢀALLꢀEVACꢀ
P137ꢀALLꢀALERTꢀLEDꢀ
P138ꢀMASTERꢀMIKEꢀPRETONEꢀPLAYINGꢀONꢀVTG2ꢀ
P139ꢀREMOTEꢀMIKEꢀ1ꢀPRETONEꢀPLAYINGꢀONꢀVTG2ꢀ
P140ꢀREMOTEꢀMIKEꢀ2ꢀPRETONEꢀPLAYINGꢀONꢀVTG2ꢀ
P141ꢀMANUALꢀAUDIOꢀEVACꢀONꢀ
P142ꢀMANUALꢀAUDIOꢀEVACꢀOFFꢀ
P143ꢀMANUALꢀAUDIOꢀEVACꢀLEDꢀ
P144ꢀDISABLEꢀSUPERVISIONꢀONꢀVTGꢀ1ꢀ(2120ꢀAPPL)ꢀ
P145ꢀDISABLEꢀSUPERVISIONꢀONꢀVTGꢀ2ꢀ(2120ꢀAPPL)ꢀ
P146ꢀEMPTYꢀAUDIOꢀSERVICEꢀQUEUEꢀ
P147ꢀEVACꢀMSGꢀPLAYINGꢀWHENꢀMICROPHONEꢀKEYEDꢀ UTILITYꢀ 128ꢁ147ꢁ0ꢀ
P148ꢀSYSTEMꢀOUTꢀOFꢀAQB'Sꢀ
P149ꢀSPEAKERꢀSWITCHꢀOFFꢀAUTOꢀ
TROUBLEꢀ128ꢁ148ꢁ0ꢀ
TROUBLEꢀ128ꢁ149ꢁ0ꢀ
UTILITYꢀ 128ꢁ150ꢁ0ꢀ
UTILITYꢀ 128ꢁ151ꢁ0ꢀ
UTILITYꢀ 128ꢁ152ꢁ0ꢀ
UTILITYꢀ 128ꢁ153ꢁ0ꢀ
UTILITYꢀ 128ꢁ154ꢁ0ꢀ
UTILITYꢀ 128ꢁ155ꢁ0ꢀ
UTILITYꢀ 128ꢁ156ꢁ0ꢀ
UTILITYꢀ 128ꢁ157ꢁ0ꢀ
P150ꢀAUDIOꢀCODINGꢀGROUPꢀ1ꢀACTIVEꢀ
P151ꢀAUDIOꢀCODINGꢀGROUPꢀ2ꢀACTIVEꢀ
P152ꢀVTGꢀ1ꢀꢁꢀAUDIOꢀSUPERVISIONꢀACTIVEꢀ
P153ꢀVTGꢀ2ꢀꢁꢀAUDIOꢀSUPERVISIONꢀACTIVEꢀ
P154ꢀPHONEꢀTALKꢀLINEꢀRELAYꢀFEEDBACKꢀ
P155ꢀPHONEꢀNETWORKꢀRELAYꢀFEEDBACKꢀ
P156ꢀLOCALꢀMASTERꢀPHONEꢀHANDSETꢀOFFꢀHOOKꢀ
P157ꢀPHONEꢀTALKꢀLINEꢀRELAYꢀCONTROLꢀINPUTꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 53 of 58
P158ꢀPHONEꢀNETWORKꢀRELAYꢀCONTROLꢀINPUTꢀ
P159ꢀPHONEꢀTALKꢀLINEꢀRELAYꢀCONTROLꢀ
UTILITYꢀ 128ꢁ158ꢁ0ꢀ
UTILITYꢀ 128ꢁ159ꢁ0ꢀ
UTILITYꢀ 128ꢁ160ꢁ0ꢀ
TROUBLEꢀ128ꢁ161ꢁ0ꢀ
UTILITYꢀ 128ꢁ162ꢁ0ꢀ
UTILITYꢀ 128ꢁ163ꢁ0ꢀ
UTILITYꢀ 128ꢁ164ꢁ0ꢀ
UTILITYꢀ 128ꢁ165ꢁ0ꢀ
P160ꢀPHONEꢀNETWORKꢀRELAYꢀCONTROLꢀ
P161ꢀMASTERꢀPHONEꢀOFFHOOKꢀSUPERVISIONꢀ
P162ꢀMASTERꢀMIKEꢀPRETONEꢀPLAYINGꢀONꢀVTG1ꢀ
P163ꢀREMOTEꢀMIKEꢀ1ꢀPRETONEꢀPLAYINGꢀONꢀVTG1ꢀ
P164ꢀREMOTEꢀMIKEꢀ2ꢀPRETONEꢀPLAYINGꢀONꢀVTG1ꢀ
P165ꢀAMPSꢀSWITCHEDꢀTOꢀBATTERYꢀ
P166ꢀENABLEꢀRMꢀPHONEꢀTOꢀRMꢀPHONEꢀCONVERSATIONꢀUTILITYꢀ 128ꢁ166ꢁ0ꢀ
P167ꢀALERTꢀMSGꢀPLAYINGꢀWHENꢀMICROPHONEꢀKEYEDꢀ UTILITYꢀ 128ꢁ167ꢁ0ꢀ
P168ꢀMICROPHONEꢀTOꢀEVACꢀINꢀEFFECTꢀ
P169ꢀMICROPHONEꢀTOꢀALERTꢀINꢀEFFECTꢀ
P170ꢀMICROPHONEꢀTOꢀTALKꢀ(CHANNELꢀ3)ꢀINꢀEFFECTꢀ
P171ꢀBACKGROUNDꢀMUSICꢀRELAYꢀCHANNELꢀ1ꢀ
P172ꢀBACKGROUNDꢀMUSICꢀRELAYꢀCHANNELꢀ2ꢀ
P173ꢀBACKGROUNDꢀMUSICꢀRELAYꢀCHANNELꢀ3ꢀ
P174ꢀVTGꢀ1ꢀCODE'SꢀPRECODEꢀPLAYINGꢀ
P175ꢀVTGꢀ1ꢀCODE'SꢀAFTERꢀCODEꢀPLAYINGꢀ
P176ꢀAFTERꢀCODEꢀSTARTꢀꢁꢀVTGꢀ1ꢀ
P177ꢀVTGꢀ1ꢀ'QUIET'ꢀMESSAGEꢀPLAYINGꢀ
P178ꢀVTGꢀ2ꢀCODE'SꢀPRECODEꢀPLAYINGꢀ
P179ꢀVTGꢀ2ꢀCODE'SꢀAFTERꢀCODEꢀPLAYINGꢀ
P180ꢀAFTERꢀCODEꢀSTARTꢀꢁꢀVTGꢀ2ꢀ
P181ꢀVTGꢀ2ꢀ'QUIET'ꢀMESSAGEꢀPLAYINGꢀ
P182ꢀ(2120ꢀAPPL)ꢀVTG1ꢀCODEꢀSTARTꢀ
P183ꢀ(2120ꢀAPPL)ꢀSTOPꢀVTG1ꢀQUEUEꢀ
P184ꢀ(2120ꢀAPPL)ꢀVTG2ꢀCODEꢀSTARTꢀ
P185ꢀ(2120ꢀAPPL)ꢀSTOPꢀVTG2ꢀQUEUEꢀ
P186ꢀMIKEꢀDISABLEꢀ
P187ꢀVTGꢀ&ꢀAMPLIFIERꢀTROUBLEꢀDISABLEꢀ
P188ꢀVTGꢀSUPERVISIONꢀTONEꢀNOTꢀACTIVEꢀ
P189ꢀSATELLITEꢀPHONEꢀTIMEOUTꢀDISABLEꢀ
P190ꢀNETWORKꢀMIKEꢀPRETONEꢀPLAYINGꢀ
P191ꢀMASTERꢀMIKEꢀKEYEDꢀ
P192ꢀREMOTEꢀMIKEꢀ1ꢀKEYEDꢀ
P193ꢀREMOTEꢀMIKEꢀ2ꢀKEYEDꢀ
P194ꢀMIKESꢀAREꢀREADYꢀTOꢀPAGEꢀ
P195ꢀS21ꢀSWITCHꢀACTIVATEDꢀ
P196ꢀRAMꢀBATTERYꢀMISSING/FAILEDꢀ
P197ꢀ2120ꢀ1ꢀCOMMꢀLOSSꢀ
UTILITYꢀ 128ꢁ168ꢁ0ꢀ
UTILITYꢀ 128ꢁ169ꢁ0ꢀ
UTILITYꢀ 128ꢁ170ꢁ0ꢀ
UTILITYꢀ 128ꢁ171ꢁ0ꢀ
UTILITYꢀ 128ꢁ172ꢁ0ꢀ
UTILITYꢀ 128ꢁ173ꢁ0ꢀ
UTILITYꢀ 128ꢁ174ꢁ0ꢀ
UTILITYꢀ 128ꢁ175ꢁ0ꢀ
UTILITYꢀ 128ꢁ176ꢁ0ꢀ
UTILITYꢀ 128ꢁ177ꢁ0ꢀ
UTILITYꢀ 128ꢁ178ꢁ0ꢀ
UTILITYꢀ 128ꢁ179ꢁ0ꢀ
UTILITYꢀ 128ꢁ180ꢁ0ꢀ
UTILITYꢀ 128ꢁ181ꢁ0ꢀ
UTILITYꢀ 128ꢁ182ꢁ0ꢀ
UTILITYꢀ 128ꢁ183ꢁ0ꢀ
UTILITYꢀ 128ꢁ184ꢁ0ꢀ
UTILITYꢀ 128ꢁ185ꢁ0ꢀ
UTILITYꢀ 128ꢁ186ꢁ0ꢀ
UTILITYꢀ 128ꢁ187ꢁ0ꢀ
TROUBLEꢀ128ꢁ188ꢁ0ꢀ
UTILITYꢀ 128ꢁ189ꢁ0ꢀ
UTILITYꢀ 128ꢁ190ꢁ0ꢀ
UTILITYꢀ 128ꢁ191ꢁ0ꢀ
UTILITYꢀ 128ꢁ192ꢁ0ꢀ
UTILITYꢀ 128ꢁ193ꢁ0ꢀ
UTILITYꢀ 128ꢁ194ꢁ0ꢀ
UTILITYꢀ 128ꢁ195ꢁ0ꢀ
TROUBLEꢀ128ꢁ196ꢁ0ꢀ
UTILITYꢀ 128ꢁ197ꢁ0ꢀ
UTILITYꢀ 128ꢁ198ꢁ0ꢀ
UTILITYꢀ 128ꢁ199ꢁ0ꢀ
UTILITYꢀ 128ꢁ200ꢁ0ꢀ
UTILITYꢀ 128ꢁ201ꢁ0ꢀ
UTILITYꢀ 128ꢁ202ꢁ0ꢀ
UTILITYꢀ 128ꢁ203ꢁ0ꢀ
UTILITYꢀ 128ꢁ204ꢁ0ꢀ
P198ꢀINHIBITꢀSONALERTꢀ
P199ꢀINHIBITꢀALARMꢀDEFAULTꢀ
P200ꢀFORCEꢀCOLDꢀSTARTꢀ
P201ꢀACꢀVOLTAGEꢀFAILURE/BROWNOUTꢀ
P202ꢀDETECTORꢀRESETꢀ
P203ꢀLCDꢀANNUNCIATORSꢀOVERRIDEꢀKEYSWITCHꢀ
P204ꢀSIGNALSꢀSILENCEDꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 54 of 58
P205ꢀTRUEALARMꢀSENSITIVITYꢀMODIFIEDꢀ
P206ꢀPRINTꢀQUEUEꢀOVERFLOWꢀ
P207ꢀNETWORKꢀDIAGNOSTICꢀMODEꢀ
P208ꢀOUTꢀOFꢀNQB'Sꢀ
P209ꢀCOMMUNICATIONSꢀSHORTꢀCIRCUITꢀTROUBLEꢀ
P210ꢀNETWORKꢀDETECTORꢀRESETꢀ
P211ꢀNETWORKꢀSYSTEMꢀRESETꢀ
TROUBLEꢀ128ꢁ205ꢁ0ꢀ
TROUBLEꢀ128ꢁ206ꢁ0ꢀ
TROUBLEꢀ128ꢁ207ꢁ0ꢀ
TROUBLEꢀ128ꢁ208ꢁ0ꢀ
TROUBLEꢀ128ꢁ209ꢁ0ꢀ
UTILITYꢀ 128ꢁ210ꢁ0ꢀ
UTILITYꢀ 128ꢁ211ꢁ0ꢀ
UTILITYꢀ 128ꢁ212ꢁ0ꢀ
UTILITYꢀ 128ꢁ213ꢁ0ꢀ
TROUBLEꢀ128ꢁ214ꢁ0ꢀ
UTILITYꢀ 128ꢁ215ꢁ0ꢀ
UTILITYꢀ 128ꢁ216ꢁ0ꢀ
UTILITYꢀ 128ꢁ217ꢁ0ꢀ
UTILITYꢀ 128ꢁ218ꢁ0ꢀ
UTILITYꢀ 128ꢁ219ꢁ0ꢀ
UTILITYꢀ 128ꢁ220ꢁ0ꢀ
UTILITYꢀ 128ꢁ221ꢁ0ꢀ
TROUBLEꢀ128ꢁ222ꢁ0ꢀ
UTILITYꢀ 128ꢁ223ꢁ0ꢀ
TROUBLEꢀ128ꢁ224ꢁ0ꢀ
TROUBLEꢀ128ꢁ225ꢁ0ꢀ
TROUBLEꢀ128ꢁ226ꢁ0ꢀ
TROUBLEꢀ128ꢁ227ꢁ0ꢀ
UTILITYꢀ 128ꢁ228ꢁ0ꢀ
TROUBLEꢀ128ꢁ229ꢁ0ꢀ
TROUBLEꢀ128ꢁ230ꢁ0ꢀ
TROUBLEꢀ128ꢁ231ꢁ0ꢀ
TROUBLEꢀ128ꢁ232ꢁ0ꢀ
UTILITYꢀ 128ꢁ250ꢁ0ꢀ
P212ꢀDETECTOR/SYSTEMꢀRESETꢀ
P213ꢀ4120ꢀNETWORKꢀCARDꢀCONFIGUREDꢀ
P214ꢀCLEARꢀVERIFICATIONꢀTALLIESꢀ
P215ꢀPRIORITYꢀ2ꢀALARMꢀDETECTꢀ
P216ꢀPRIORITYꢀ2ꢀALARMꢀRESETꢀREQUESTꢀ
P217ꢀNETWORKꢀSIGNALꢀSILENCEꢀ
P218ꢀUNACKNOWLEDGEDꢀPRIORITYꢀ2ꢀALARMꢀEXISTSꢀ
P219ꢀMASTERꢀPRIORITYꢀ2ꢀALARMꢀACKꢀKEYꢀ
P220ꢀNETWORKꢀPRIORITYꢀ2ꢀRESETꢀ
P221ꢀSIGNALSꢀACTIVEꢀꢁꢀOFFꢀONꢀSILENCEꢀ
P222ꢀREMOTEꢀDOWNLOADꢀENABLEDꢀ
P223ꢀMASTERꢀMICROPHONEꢀREADYꢀTOꢀTALKꢀ
P224ꢀNETWORKꢀINITIALIZATIONꢀINCOMPLETEꢀ
P225ꢀNETWORKꢀOPERATINGꢀINꢀDEGRADEDꢀSTYLEꢁ7ꢀ
P226ꢀNETWORKꢀINITIALIZATIONꢀINꢀPROGRESSꢀ
P227ꢀSDACTꢀDATABASEꢀVERSIONꢀMISMATCHꢀ
P228ꢀPREVENTꢀTIME/DATEꢀLOGGINGꢀ
P229ꢀTRUEALERTꢀSILENTꢀTESTꢀACTIVEꢀ
P230ꢀTRUEALERTꢀDEVICEꢀTESTꢀMODEꢀACTIVEꢀ
P231ꢀEXTRAꢀNODEꢀONꢀNETWORKꢀ
P232ꢀNETWORKꢀPOINTꢀLABELꢀUPDATINGꢀINHIBITEDꢀ
P250ꢀENABLEꢀENDꢀPAIRꢀANDꢀMONITORꢀLOGGINGꢀ
ꢀ
AnalogꢀPseudo'sꢀdoꢀnotꢀhaveꢀalarmꢀstates,ꢀtheyꢀhaveꢀphysicalꢀvaluesꢀsuchꢀasꢀtheꢀday,ꢀdate,ꢀ
time,ꢀnumberꢀofꢀfireꢀevents,ꢀnumberꢀofꢀtroublesꢀandꢀsoꢀon.ꢀ
ꢀ
ꢀA0ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ NUMBERꢀOFꢀSYSTEMꢀFIREꢀALARMSꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA1ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ NUMBERꢀOFꢀSYSTEMꢀSUPERVISORIESꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA2ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ NUMBERꢀOFꢀSYSTEMꢀTROUBLESꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA3ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ NUMBERꢀOFꢀOLDꢀ(UNCLEARED)ꢀFIREꢀALARMSꢀꢀꢀꢀꢀꢀꢀꢀ
ANALOGꢀ 144ꢁ0ꢁ0ꢀ
ANALOGꢀ 144ꢁ1ꢁ0ꢀ
ANALOGꢀ 144ꢁ2ꢁ0ꢀ
ANALOGꢀ 144ꢁ3ꢁ0ꢀ
ꢀA4ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ NUMBERꢀOFꢀOLDꢀ(UNCLEARED)ꢀSUPERVISORIESꢀꢀꢀꢀꢀꢀ ANALOGꢀ 144ꢁ4ꢁ0ꢀ
ꢀA5ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ NUMBERꢀOFꢀOLDꢀ(UNCLEARED)ꢀTROUBLESꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA6ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ CURRENTꢀHOURꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA7ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ CURRENTꢀMINUTEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA8ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ CURRENTꢀSECONDꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA9ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ CURRENTꢀDAYꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA10ꢀꢀꢀꢀꢀꢀꢀꢀꢀ CURRENTꢀMONTHꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA11ꢀꢀꢀꢀꢀꢀꢀꢀꢀ CURRENTꢀYEARꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA12ꢀꢀꢀꢀꢀꢀꢀꢀꢀ CURRENTꢀACCESSꢀLEVELꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA13ꢀꢀꢀꢀꢀꢀꢀꢀꢀ ACCESSꢀLEVELꢀTIMEOUTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ANALOGꢀ 144ꢁ5ꢁ0ꢀ
ANALOGꢀ 144ꢁ6ꢁ0ꢀ
ANALOGꢀ 144ꢁ7ꢁ0ꢀ
ANALOGꢀ 144ꢁ8ꢁ0ꢀ
ANALOGꢀ 144ꢁ9ꢁ0ꢀ
ANALOGꢀ 144ꢁ10ꢁ0ꢀ
ANALOGꢀ 144ꢁ11ꢁ0ꢀ
ANALOGꢀ 144ꢁ12ꢁ0ꢀ
TIMERꢀ
144ꢁ13ꢁ0ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 55 of 58
ꢀA14ꢀꢀꢀꢀꢀꢀꢀꢀꢀ SYSTEMꢀRESETꢀWINDOWꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA15ꢀꢀꢀꢀꢀꢀꢀꢀꢀ SYSTEMꢀRESETꢀWINDOWꢀTIMERꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA16ꢀꢀꢀꢀꢀꢀꢀꢀꢀ DETECTORꢀRESETꢀPULSEꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA17ꢀꢀꢀꢀꢀꢀꢀꢀꢀ 4ꢁWIREꢀRESETꢀRELAYꢀPULSEꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA18ꢀꢀꢀꢀꢀꢀꢀꢀꢀ FIREꢀALARMꢀCLEARꢀDELAYꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA19ꢀꢀꢀꢀꢀꢀꢀꢀꢀ FIREꢀALARMꢀCLEARꢀDELAYꢀTIMERꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA20ꢀꢀꢀꢀꢀꢀꢀꢀꢀ FIREꢀALARMꢀCLEARꢀPULSEꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA21ꢀꢀꢀꢀꢀꢀꢀꢀꢀ SYSTEMꢀRESETꢀPULSEꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA22ꢀꢀꢀꢀꢀꢀꢀꢀꢀ ALARMꢀSILENCEꢀINHIBITꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA23ꢀꢀꢀꢀꢀꢀꢀꢀꢀ ALARMꢀSILENCEꢀINHIBITꢀTIMERꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA24ꢀꢀꢀꢀꢀꢀꢀꢀꢀ FIREꢀALARMꢀCUTOUTꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA25ꢀꢀꢀꢀꢀꢀꢀꢀꢀ FIREꢀALARMꢀCUTOUTꢀTIMERꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA26ꢀꢀꢀꢀꢀꢀꢀꢀꢀ FIREꢀALARMꢀCUTOUTꢀSILENCEꢀPULSEꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA27ꢀꢀꢀꢀꢀꢀꢀꢀꢀ TROUBLEꢀREMINDERꢀCYCLEꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA28ꢀꢀꢀꢀꢀꢀꢀꢀꢀ TROUBLEꢀREMINDERꢀOFFꢁTIMEꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA29ꢀꢀꢀꢀꢀꢀꢀꢀꢀ TROUBLEꢀREMINDERꢀONꢁTIMEꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA30ꢀꢀꢀꢀꢀꢀꢀꢀꢀ DOORꢀHOLDERꢀALARMꢀDROPꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
TIMERꢀ
ANALOGꢀ 144ꢁ15ꢁ0ꢀ
TIMERꢀ
TIMERꢀ
TIMERꢀ
144ꢁ14ꢁ0ꢀ
144ꢁ16ꢁ0ꢀ
144ꢁ17ꢁ0ꢀ
144ꢁ18ꢁ0ꢀ
ANALOGꢀ 144ꢁ19ꢁ0ꢀ
TIMERꢀ
TIMERꢀ
TIMERꢀ
ANALOGꢀ 144ꢁ23ꢁ0ꢀ
TIMERꢀ 144ꢁ24ꢁ0ꢀ
ANALOGꢀ 144ꢁ25ꢁ0ꢀ
TIMERꢀ
TIMERꢀ
ANALOGꢀ 144ꢁ28ꢁ0ꢀ
ANALOGꢀ 144ꢁ29ꢁ0ꢀ
144ꢁ20ꢁ0ꢀ
144ꢁ21ꢁ0ꢀ
144ꢁ22ꢁ0ꢀ
144ꢁ26ꢁ0ꢀ
144ꢁ27ꢁ0ꢀ
TIMERꢀ
144ꢁ30ꢁ0ꢀ
ꢀA31ꢀꢀꢀꢀꢀꢀꢀꢀꢀ DOORꢀHOLDERꢀALARMꢀDROPꢀTIMERꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀ ANALOGꢀ 144ꢁ31ꢁ0ꢀ
ꢀA32ꢀꢀꢀꢀꢀꢀꢀꢀꢀ DOORꢀHOLDERꢀBROWNOUTꢀDROPꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ TIMERꢀ 144ꢁ32ꢁ0ꢀ
ꢀA33ꢀꢀꢀꢀꢀꢀꢀꢀꢀ DOORꢀHOLDERꢀBROWNOUTꢀDROPꢀTIMERꢀSETPOINTꢀꢀꢀANALOGꢀ 144ꢁ33ꢁ0ꢀ
ꢀA34ꢀꢀꢀꢀꢀꢀꢀꢀꢀ SYSTEMꢀSTARTUPꢀPULSEꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA35ꢀꢀꢀꢀꢀꢀꢀꢀꢀ FIREꢀALARMꢀAUDIBLEꢀSIGNALꢀOPERATIONꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA36ꢀꢀꢀꢀꢀꢀꢀꢀꢀ FIREꢀALARMꢀVISUALꢀSIGNALꢀOPERATIONꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA37ꢀꢀꢀꢀꢀꢀꢀꢀꢀ ALARMꢀVERIFICATIONꢀꢁꢀRETARDꢀTIMEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA38ꢀꢀꢀꢀꢀꢀꢀꢀꢀ ALARMꢀVERIFICATIONꢀꢁꢀRESETꢀTIMEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA39ꢀꢀꢀꢀꢀꢀꢀꢀꢀ ALARMꢀVERIFICATIONꢀꢁꢀCONFIRMATIONꢀTIMEꢀꢀꢀꢀꢀꢀꢀ
ꢀA40ꢀꢀꢀꢀꢀꢀꢀꢀꢀ ALARMꢀVERIFICATIONꢀꢁꢀTALLYꢀLIMITꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA41ꢀꢀꢀꢀꢀꢀꢀꢀꢀ WALKꢀTESTꢀABORTꢀTIMEOUTꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA42ꢀꢀꢀꢀꢀꢀꢀꢀꢀ WALKꢀTESTꢀREACTIVATEꢀDELAYꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA43ꢀꢀꢀꢀꢀꢀꢀꢀꢀ MONITORꢀZONEꢀENABLEꢀDELAYꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA44ꢀꢀꢀꢀꢀꢀꢀꢀꢀ CODEDꢀINPUTꢀTIMEOUTꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA45ꢀꢀꢀꢀꢀꢀꢀꢀꢀ OFFꢀTIMEꢀAFTERꢀPNISꢀ(NONꢁCONT.)ꢀCODESꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA46ꢀꢀꢀꢀꢀꢀꢀꢀꢀ CITYꢀCIRCUITꢀCONFIGURATIONꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
TIMERꢀ
144ꢁ34ꢁ0ꢀ
ANALOGꢀ 144ꢁ35ꢁ0ꢀ
ANALOGꢀ 144ꢁ36ꢁ0ꢀ
ANALOGꢀ 144ꢁ37ꢁ0ꢀ
ANALOGꢀ 144ꢁ38ꢁ0ꢀ
ANALOGꢀ 144ꢁ39ꢁ0ꢀ
ANALOGꢀ 144ꢁ40ꢁ0ꢀ
ANALOGꢀ 144ꢁ41ꢁ0ꢀ
ANALOGꢀ 144ꢁ42ꢁ0ꢀ
ANALOGꢀ 144ꢁ43ꢁ0ꢀ
ANALOGꢀ 144ꢁ44ꢁ0ꢀ
ANALOGꢀ 144ꢁ45ꢁ0ꢀ
ANALOGꢀ 144ꢁ46ꢁ0ꢀ
ꢀA47ꢀꢀꢀꢀꢀꢀꢀꢀꢀ ALERTꢀTONE/MSGꢀAFTERꢀMICROPHONEꢀUNKEYEDꢀꢀꢀꢀꢀꢀANALOGꢀ 144ꢁ47ꢁ0ꢀ
ꢀA48ꢀꢀꢀꢀꢀꢀꢀꢀꢀ TOTALꢀAUDIOꢀCHANNELSꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA49ꢀꢀꢀꢀꢀꢀꢀꢀꢀ CHANNELꢀ1ꢀROUTINGꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA50ꢀꢀꢀꢀꢀꢀꢀꢀꢀ CHANNELꢀ2ꢀROUTINGꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA51ꢀꢀꢀꢀꢀꢀꢀꢀꢀ CHANNELꢀ3ꢀROUTINGꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA52ꢀꢀꢀꢀꢀꢀꢀꢀꢀ LOCALꢀROUTINGꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ANALOGꢀ 144ꢁ48ꢁ0ꢀ
ANALOGꢀ 144ꢁ49ꢁ0ꢀ
ANALOGꢀ 144ꢁ50ꢁ0ꢀ
ANALOGꢀ 144ꢁ51ꢁ0ꢀ
ANALOGꢀ 144ꢁ52ꢁ0ꢀ
ꢀA53ꢀꢀꢀꢀꢀꢀꢀꢀꢀ EVACꢀTONE/MSGꢀAFTERꢀMICROPHONEꢀUNKEYEDꢀꢀꢀꢀꢀꢀꢀANALOGꢀ 144ꢁ53ꢁ0ꢀ
ꢀA54ꢀꢀꢀꢀꢀꢀꢀꢀꢀ SUPERVISIONꢀMSG#ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA55ꢀꢀꢀꢀꢀꢀꢀꢀꢀ EVACUATIONꢀMSG#ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA56ꢀꢀꢀꢀꢀꢀꢀꢀꢀ ALERTꢀMSG#ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA57ꢀꢀꢀꢀꢀꢀꢀꢀꢀ DRILLꢀMSG#ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA58ꢀꢀꢀꢀꢀꢀꢀꢀꢀ ALLꢀCLEARꢀMSG#ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA59ꢀꢀꢀꢀꢀꢀꢀꢀꢀ AUXꢀ1ꢀMSG#ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA60ꢀꢀꢀꢀꢀꢀꢀꢀꢀ AUXꢀ2ꢀMSG#ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ANALOGꢀ 144ꢁ54ꢁ0ꢀ
ANALOGꢀ 144ꢁ55ꢁ0ꢀ
ANALOGꢀ 144ꢁ56ꢁ0ꢀ
ANALOGꢀ 144ꢁ57ꢁ0ꢀ
ANALOGꢀ 144ꢁ58ꢁ0ꢀ
ANALOGꢀ 144ꢁ59ꢁ0ꢀ
ANALOGꢀ 144ꢁ60ꢁ0ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 56 of 58
ꢀA61ꢀꢀꢀꢀꢀꢀꢀꢀꢀ MICROPHONEꢀPRETONEꢀMSG#ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA62ꢀꢀꢀꢀꢀꢀꢀꢀꢀ PHONEꢀOFFHOOKꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA63ꢀꢀꢀꢀꢀꢀꢀꢀꢀ PHONEꢀCALLBACKꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA64ꢀꢀꢀꢀꢀꢀꢀꢀꢀ PHONEꢀTIMEOUTꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA65ꢀꢀꢀꢀꢀꢀꢀꢀꢀ REMOTEꢀMASTERꢀPHONEꢀTIMEOUTꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA66ꢀꢀꢀꢀꢀꢀꢀꢀꢀ SPEAKERꢀSWITCHꢀOFFꢀAUTOꢀCOUNTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA67ꢀꢀꢀꢀꢀꢀꢀꢀꢀ AUDIOꢀRESETꢀPULSEꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA68ꢀꢀꢀꢀꢀꢀꢀꢀꢀ VTGꢀ1ꢀPRIORITYꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ANALOGꢀ 144ꢁ61ꢁ0ꢀ
TIMERꢀ
TIMERꢀ
TIMERꢀ
TIMERꢀ
144ꢁ62ꢁ0ꢀ
144ꢁ63ꢁ0ꢀ
144ꢁ64ꢁ0ꢀ
144ꢁ65ꢁ0ꢀ
ANALOGꢀ 144ꢁ66ꢁ0ꢀ
TIMERꢀ 144ꢁ67ꢁ0ꢀ
ANALOGꢀ 144ꢁ68ꢁ0ꢀ
ANALOGꢀ 144ꢁ69ꢁ0ꢀ
ANALOGꢀ 144ꢁ70ꢁ0ꢀ
ANALOGꢀ 144ꢁ71ꢁ0ꢀ
ANALOGꢀ 144ꢁ72ꢁ0ꢀ
ANALOGꢀ 144ꢁ73ꢁ0ꢀ
ꢀA69ꢀꢀꢀꢀꢀꢀꢀꢀꢀ VTGꢀ2ꢀPRIORITYꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA70ꢀꢀꢀꢀꢀꢀꢀꢀꢀ CHANNELꢀ1ꢀROUTINGꢀPRIORITYꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA71ꢀꢀꢀꢀꢀꢀꢀꢀꢀ CHANNELꢀ2ꢀROUTINGꢀPRIORITYꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA72ꢀꢀꢀꢀꢀꢀꢀꢀꢀ CHANNELꢀ3ꢀROUTINGꢀPRIORITYꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA73ꢀꢀꢀꢀꢀꢀꢀꢀꢀ LOCALꢀSPEAKERꢀROUTINGꢀPRIORITYꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA74ꢀꢀꢀꢀꢀꢀꢀꢀꢀ AUDIOꢀSUPERVISIONꢀPULSEꢀTIMERꢀVTG1ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA75ꢀꢀꢀꢀꢀꢀꢀꢀꢀ AUDIOꢀSUPERVISIONꢀPULSEꢀTIMERꢀVTG2ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA76ꢀꢀꢀꢀꢀꢀꢀꢀꢀ ENABLE/DISABLEꢀSTATISTICꢀGROUPꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA77ꢀꢀꢀꢀꢀꢀꢀꢀꢀ ENABLE/DISABLEꢀSTATISTICꢀOUTPUTꢀPORTꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA78ꢀꢀꢀꢀꢀꢀꢀꢀꢀ 5ꢀSECꢀTIMERꢀFORꢀREMOTEꢀMASTERꢀPHONESꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA79ꢀꢀꢀꢀꢀꢀꢀꢀꢀ CLEARꢀPEAKꢀPULSEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA80ꢀꢀꢀꢀꢀꢀꢀꢀꢀ PRECODEꢀMESSAGEꢀNUMBERꢀꢁꢀVTGꢀ1ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA81ꢀꢀꢀꢀꢀꢀꢀꢀꢀ AFTERꢀCODEꢀMESSAGEꢀNUMBERꢀꢁꢀVTGꢀ1ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA82ꢀꢀꢀꢀꢀꢀꢀꢀꢀ PRECODEꢀMESSAGEꢀNUMBERꢀꢁꢀVTGꢀ2ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA83ꢀꢀꢀꢀꢀꢀꢀꢀꢀ AFTERꢀCODEꢀMESSAGEꢀNUMBERꢀꢁꢀVTGꢀ2ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA84ꢀꢀꢀꢀꢀꢀꢀꢀ'ꢀQUIET'ꢀMESSAGEꢀNUMBERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA85ꢀꢀꢀꢀꢀꢀꢀꢀꢀ 2ꢀSECONDꢀTIMERꢀꢁꢀVTGꢀ1ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
TIMERꢀ
TIMERꢀ
144ꢁ74ꢁ0ꢀ
144ꢁ75ꢁ0ꢀ
ANALOGꢀ 144ꢁ76ꢁ0ꢀ
ANALOGꢀ 144ꢁ77ꢁ0ꢀ
TIMERꢀ
144ꢁ78ꢁ0ꢀ
ANALOGꢀ 144ꢁ79ꢁ0ꢀ
ANALOGꢀ 144ꢁ80ꢁ0ꢀ
ANALOGꢀ 144ꢁ81ꢁ0ꢀ
ANALOGꢀ 144ꢁ82ꢁ0ꢀ
ANALOGꢀ 144ꢁ83ꢁ0ꢀ
ANALOGꢀ 144ꢁ84ꢁ0ꢀ
TIMERꢀ
TIMERꢀ
TIMERꢀ
144ꢁ85ꢁ0ꢀ
144ꢁ86ꢁ0ꢀ
144ꢁ87ꢁ0ꢀ
ꢀA86ꢀꢀꢀꢀꢀꢀꢀꢀꢀ 2ꢀSECONDꢀTIMERꢀꢁꢀVTGꢀ2ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA87ꢀꢀꢀꢀꢀꢀꢀꢀꢀ MIKEꢀINHIBITꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA88ꢀꢀꢀꢀꢀꢀꢀꢀꢀ MIKEꢀINHIBITꢀTIMERꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA89ꢀꢀꢀꢀꢀꢀꢀꢀꢀ PHONEꢀCALLBACKꢀTIMERꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA90ꢀꢀꢀꢀꢀꢀꢀꢀꢀ PHONEꢀTIMEOUTꢀTIMERꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA91ꢀꢀꢀꢀꢀꢀꢀꢀꢀ VTGꢀ&ꢀAMPLIFIERꢀTROUBLEꢀDISABLEꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA92ꢀꢀꢀꢀꢀꢀꢀꢀꢀ SUPERVISIONꢀNOTꢀACTIVEꢀꢁꢀTBLꢀDELAYꢀTIMERꢀꢀꢀꢀꢀ
ꢀA93ꢀꢀꢀꢀꢀꢀꢀꢀꢀ 4ꢀWIREꢀDETECTORꢀRESETꢀEXTENDꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA94ꢀꢀꢀꢀꢀꢀꢀꢀꢀ ACTIVEꢀMESSAGEꢀNUMBERꢀꢁꢀVTGꢀ1ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA95ꢀꢀꢀꢀꢀꢀꢀꢀꢀ ACTIVEꢀMESSAGEꢀNUMBERꢀꢁꢀVTGꢀ2ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA96ꢀꢀꢀꢀꢀꢀꢀꢀꢀ ACTUALꢀCHIPSETꢀPLUGGEDꢀINTOꢀVTGꢀ1ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA97ꢀꢀꢀꢀꢀꢀꢀꢀꢀ ACTUALꢀCHIPSETꢀPLUGGEDꢀINTOꢀVTGꢀ2ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA98ꢀꢀꢀꢀꢀꢀꢀꢀꢀ BATTERYꢀTROUBLEꢀCOUNTERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA99ꢀꢀꢀꢀꢀꢀꢀꢀꢀ ACꢀPOWERꢀFAILꢀCOUNTERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA100ꢀꢀꢀꢀꢀꢀꢀꢀSYSTEMꢀTYPEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ANALOGꢀ 144ꢁ88ꢁ0ꢀ
ANALOGꢀ 144ꢁ89ꢁ0ꢀ
ANALOGꢀ 144ꢁ90ꢁ0ꢀ
TIMERꢀ
TIMERꢀ
TIMERꢀ
144ꢁ91ꢁ0ꢀ
144ꢁ92ꢁ0ꢀ
144ꢁ93ꢁ0ꢀ
ANALOGꢀ 144ꢁ94ꢁ0ꢀ
ANALOGꢀ 144ꢁ95ꢁ0ꢀ
ANALOGꢀ 144ꢁ96ꢁ0ꢀ
ANALOGꢀ 144ꢁ97ꢁ0ꢀ
COUNTERꢀ144ꢁ98ꢁ0ꢀ
COUNTERꢀ144ꢁ99ꢁ0ꢀ
ANALOGꢀ 144ꢁ100ꢁ0ꢀ
ANALOGꢀ 144ꢁ101ꢁ0ꢀ
ANALOGꢀ 144ꢁ102ꢁ0ꢀ
ANALOGꢀ 144ꢁ103ꢁ0ꢀ
ANALOGꢀ 144ꢁ104ꢁ0ꢀ
ANALOGꢀ 144ꢁ105ꢁ0ꢀ
ANALOGꢀ 144ꢁ106ꢁ0ꢀ
ANALOGꢀ 144ꢁ107ꢁ0ꢀ
ꢀA101ꢀꢀꢀꢀꢀꢀꢀꢀFIRSTꢀSTAGEꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA102ꢀꢀꢀꢀꢀꢀꢀꢀFIRSTꢀSTAGEꢀTIMERꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA103ꢀꢀꢀꢀꢀꢀꢀꢀMASTERꢀMIKEꢀ5ꢀSECONDꢀUNKEYꢀDELAYꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA104ꢀꢀꢀꢀꢀꢀꢀꢀREMOTEꢀMIKEꢀ1ꢀꢀ5ꢀSECONDꢀUNKEYꢀDELAYꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA105ꢀꢀꢀꢀꢀꢀꢀꢀREMOTEꢀMIKEꢀ2ꢀꢀ5ꢀSECONDꢀUNKEYꢀDELAYꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA106ꢀꢀꢀꢀꢀꢀꢀꢀMASTERꢀMIKE'SꢀPRETONEꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA107ꢀꢀꢀꢀꢀꢀꢀꢀMASTERꢀMIKE'SꢀPRETONEꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 57 of 58
ꢀA108ꢀꢀꢀꢀꢀꢀꢀꢀREMOTEꢀMIKEꢀ1'SꢀPRETONEꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA109ꢀꢀꢀꢀꢀꢀꢀꢀREMOTEꢀMIKEꢀ1'SꢀPRETONEꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA110ꢀꢀꢀꢀꢀꢀꢀꢀREMOTEꢀMIKEꢀ2'SꢀPRETONEꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA111ꢀꢀꢀꢀꢀꢀꢀꢀREMOTEꢀMIKEꢀ2'SꢀPRETONEꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA112ꢀꢀꢀꢀꢀꢀꢀꢀGROUNDꢀTROUBLEꢀCOUNTERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA113ꢀꢀꢀꢀꢀꢀꢀꢀPAGINGꢀCHANNELꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA114ꢀꢀꢀꢀꢀꢀꢀꢀTRUEALARMꢀMODIFICATIONꢀCOUNTERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA115ꢀꢀꢀꢀꢀꢀꢀꢀEXCESSIVELYꢀDIRTYꢀꢀꢀꢀ(OUTꢀOFꢀRANGE)ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA116ꢀꢀꢀꢀꢀꢀꢀꢀDIRTYꢀSENSORꢀCOUNTERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA117ꢀꢀꢀꢀꢀꢀꢀꢀALMOSTꢀDIRTYꢀCOUNTERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA118ꢀꢀꢀꢀꢀꢀꢀꢀALARMSꢀSILENCEDꢀDELAYꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ANALOGꢀ 144ꢁ108ꢁ0ꢀ
ANALOGꢀ 144ꢁ109ꢁ0ꢀ
ANALOGꢀ 144ꢁ110ꢁ0ꢀ
ANALOGꢀ 144ꢁ111ꢁ0ꢀ
COUNTERꢀ144ꢁ112ꢁ0ꢀ
ANALOGꢀ 144ꢁ113ꢁ0ꢀ
COUNTERꢀ144ꢁ114ꢁ0ꢀ
ANALOGꢀ 144ꢁ115ꢁ0ꢀ
COUNTERꢀ144ꢁ116ꢁ0ꢀ
COUNTERꢀ144ꢁ117ꢁ0ꢀ
TIMERꢀ
144ꢁ118ꢁ0ꢀ
ꢀA119ꢀꢀꢀꢀꢀꢀꢀꢀNUMBERꢀOFꢀLOCALꢀSYSTEMꢀPOINTS'ꢀTROUBLESꢀꢀꢀꢀꢀꢀ COUNTERꢀ144ꢁ119ꢁ0ꢀ
ꢀA120ꢀꢀꢀꢀꢀꢀꢀꢀSYSTEMꢀPAGINGꢀSTATUSꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA121ꢀꢀꢀꢀꢀꢀꢀꢀKEYPADꢀINACTIVITYꢀTIMEOUTꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA122ꢀꢀꢀꢀꢀꢀꢀꢀNUMBERꢀOFꢀSYSTEMꢀPRIORITYꢀ2ꢀALARMSꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA123ꢀꢀꢀꢀꢀꢀꢀꢀNUMBERꢀOFꢀOLDꢀ(UNCLEARED)ꢀPRI2ꢀALARMSꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA124ꢀꢀꢀꢀꢀꢀꢀꢀPRI2ꢀRESETꢀWINDOWꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA125ꢀꢀꢀꢀꢀꢀꢀꢀPRI2ꢀRESETꢀWINDOWꢀTIMERꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA126ꢀꢀꢀꢀꢀꢀꢀꢀPRI2ꢀALARMꢀCLEARꢀDELAYꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA127ꢀꢀꢀꢀꢀꢀꢀꢀPRI2ꢀALARMꢀCLEARꢀDELAYꢀTIMERꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA128ꢀꢀꢀꢀꢀꢀꢀꢀPRI2ꢀALARMꢀCLEARꢀPULSEꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA129ꢀꢀꢀꢀꢀꢀꢀꢀPRIORITYꢀ2ꢀRESETꢀPULSEꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA130ꢀꢀꢀꢀꢀꢀꢀꢀPRIORITYꢀ2ꢀRESETꢀSTARTꢀTIMERꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA131ꢀꢀꢀꢀꢀꢀꢀꢀSUPERVISIONꢀDELAYꢀSETPOINTꢀCHL1ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA132ꢀꢀꢀꢀꢀꢀꢀꢀSUPERVISIONꢀDELAYꢀSETPOINTꢀCHL2ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀA133ꢀꢀꢀꢀꢀꢀꢀꢀSUPERVISIONꢀNOTꢀACTIVEꢀDELAYꢀSETPOINTꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀ
ANALOGꢀ 144ꢁ120ꢁ0ꢀ
ANALOGꢀ 144ꢁ121ꢁ0ꢀ
ANALOGꢀ 144ꢁ122ꢁ0ꢀ
ANALOGꢀ 144ꢁ123ꢁ0ꢀ
TIMERꢀ
ANALOGꢀ 144ꢁ125ꢁ0ꢀ
TIMERꢀ 144ꢁ126ꢁ0ꢀ
ANALOGꢀ 144ꢁ127ꢁ0ꢀ
144ꢁ124ꢁ0ꢀ
TIMERꢀ
TIMERꢀ
TIMERꢀ
144ꢁ128ꢁ0ꢀ
144ꢁ129ꢁ0ꢀ
144ꢁ130ꢁ0ꢀ
ANALOGꢀ 144ꢁ131ꢁ0ꢀ
ANALOGꢀ 144ꢁ132ꢁ0ꢀ
ANALOGꢀ 144ꢁ133ꢁ0ꢀ
ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-8700-41 Simplex 4100 Driver Manual
Page 58 of 58
THISꢀPAGEꢀINTENTIONALLYꢀLEFTꢀBLANKꢀ
ꢀ
ꢀ
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
|